Add the missing license and copyright information which never made it
into the analog driver when the original driver was split in two as part
of the review process.
Link: https://lkml.kernel.org/r/1465582725-30183-3-git-send-email-srinivas.kandagatla@linaro.org
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As snd_soc_jack_report() can sleep, move handling of mbhc events to a
thread context rather than in interrupt context.
Fixes: de66b34550 ('ASoC: codecs: msm8916-wcd-analog: add MBHC support')
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To setup regmap, ALSA SoC has snd_soc_component_init_regmap() and
.get_regmap. But these are duplicated feature.
Let's use snd_soc_component_init_regmap() and remove .get_regmap
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This codec is configurable for only 16 bit and 32 bit samples, so reflect
this in the supported formats also remove 24bit sample from supported list.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397957
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The macro used to set the microphone bias level causes the
snd_soc_write() call to overwrite other fields in the CDC_A_MICB_1_VAL
register. The macro also does not return the proper level value
to use. This fixes this by preserving all bits from the register
that are not the level while setting the level.
Signed-off-by: Jean-François Têtu <jean-francois.tetu@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The very first time a headset is plugged in, detection is unreliable
because bias hasn't been configured yet, it's done once a mechanical
insertion interrupt has been triggered, so following insertions (and
thus detections) are not affected.
To fix the very first detection, the bias must also be configured in the
function that setup the MBHC. Move pm8916_wcd_setup_mbhc after
pm8916_mbhc_configure_bias to avoid a forward declaration.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo snd_soc_msm8916_analog | grep alias
$
After this patch:
$ modinfo snd_soc_msm8916_analog | grep alias
alias: of:N*T*Cqcom,pm8916-wcd-analog-codecC*
alias: of:N*T*Cqcom,pm8916-wcd-analog-codec
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd-analog uses button0 to differentiate between headphone and
headset. Under some circumstances, button pressed and released
interrupts are not fired as the driver expects it.
For instance, with some connectors, there are spurious button-pressed
interrupts when unplugging a headphone, without the corresponding
button-released interrupt. But the codec always alternates between
button pressed and released interrupts, it cannot fire two interrupts of
the same kind in a row. That means that when the headphone is plugged
back, only a button-released interrupt will be fired instead of pressed
then released. This causes the driver to report headphone as headset.
By changing the logic and relying on button 0 release interrupt, the
driver could be made more robust for connectors that differ from the one
used on the Dragonboard's audio mezzanine.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static checkers complain that unsigned int val is always >= 0. The
context is that snd_soc_read() returns -1U on error. This is harmless
because we're checking that CDC_A_MBHC_RESULT_1_BTN_RESULT_MASK is not
set, and it will always be set for -1U. I could have just removed the
check against -1 but I preserved it because I thought it helped with
readability.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MBHC (MultiButton Headset Control) support is available in pm8921 in two
blocks, one to detect mechanical headset insertion and removal and other
block to support headset type detection and 5 button detection and othe
features like impedance calculation.
This patch adds support to:
1> Support to NC and NO type of headset Jacks.
2> Mechanical insertion and detection of headset jack.
3> Detect a 3 pole Headphone and a 4 pole Headset.
4> Detect 5 buttons.
Tested it on DB410c with Audio Mezz board with 4 pole and 3 pole
headset/headphones.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds bindings in DT to provide required micbias voltage which
could be specific to board. With this new binding, now the mic bias
voltage is left at hardware default value if the device tree does not
specify any mic bias voltage value. Correct micbias value is required
for mbhc buttons to work.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_ops are not supposed to change at runtime. All functions
working with snd_soc_dai_ops provided by <sound/soc-dai.h> work with
const snd_soc_dai_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch move the codec reset code from dai ops to codec probe, so
that the codec is not held in reset when headset detection block is
still active.
Without this patch the codec block will be in reset as long as its not
actively used, which means headset events will not be functional if the
codec dai is not actively used. Point to note is that the headset
detection blocks will work in low power when there is no active audio
usecase and switch to micbias source when audio usecase is active.
Existing dapms should put the codec in low power state anyway when there
is no audio usecase.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_soc_codec_driver structures as const as they are only passed
as an argument to the function snd_soc_register_codec. This argument is
of type const, so declare the structures with this property as const.
In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in
a copy operation along with getting passed to snd_soc_register_codec.
So, it can be made const too.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
position p;
@@
static struct snd_soc_codec_driver s@p={...};
@good1@
identifier match.s;
position p;
@@
snd_soc_register_codec(...,&s@p,...)
@bad@
identifier match.s;
position p!={match.p,good1.p};
@@
s@p
@depends on !bad disable optional_qualifier@
identifier match.s;
@@
static
+const
struct snd_soc_codec_driver s={...};
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wrong bit is assigned to DIG_CLK_CTL_RXD3_CLK_EN, change it for the
correct one.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This structure is only stored in the ops field of a snd_soc_dai_driver
structure. That field is declared const, so snd_soc_dai_ops structures
that have this property can be declared as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A function snd_soc_update_bits() is an application of
regmap_update_bits_base(). This function takes some arguments for bitmask
and new value, thus the arguments should be a type which has width.
However bool is used to variable for the argument. This brings truncation
and results in invalid operation.
This commit fixes this bug by using unsigned int type, instead of bool.
This bug is detected by sparse:
smsm8916-wcd-analog.c:809:43: warning: odd constant _Bool cast (40 becomes 1)
smsm8916-wcd-analog.c:814:43: warning: odd constant _Bool cast (40 becomes 1)
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm8916_wcd_analog_enable_micbias_int1() should set micbias1_cap_mode
rather than micbias2_cap_mode.
Also change the order of pm8916_wcd_analog_enable_micbias_int1/init2
functions for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the code which is not parsing dt from pm8916_wcd_analog_parse_dt()
to make it clear to reader.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts (Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Analog part of the Codec which is integrated
into PMIC PM8916.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Johan Hovold