Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the use_single_rw flag to regmap config since the
device does not support bulk transactions over i2c.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Declare snd_soc_codec_driver structures as const as they are only passed
as an argument to the function snd_soc_register_codec. This argument is
of type const, so declare the structures with this property as const.
In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in
a copy operation along with getting passed to snd_soc_register_codec.
So, it can be made const too.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
position p;
@@
static struct snd_soc_codec_driver s@p={...};
@good1@
identifier match.s;
position p;
@@
snd_soc_register_codec(...,&s@p,...)
@bad@
identifier match.s;
position p!={match.p,good1.p};
@@
s@p
@depends on !bad disable optional_qualifier@
identifier match.s;
@@
static
+const
struct snd_soc_codec_driver s={...};
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Very fast systems may violate the minimum constraints for time the reset
line needs to remain low, or communicate with the device too soon after
releasing the reset. Fix this by adding some delays in to allow the chip
to properly reset, also factor out the reset into a function as it is
likely it will be re-used in later additions to the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Zero is a totally valid value to specify for the bst_ipk, as such we
should append CS35L35_VALID_PDATA to ensure that it actually makes it
into the register value.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the Boost Inductor parameters based off the size of the inductor
on the HW setup
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the chip the IMON signal is a full 24-bits however normally only
some of the bits will be sent over the bus. The chip provides a field
to select which bits of the IMON will be sent back, this is the only
feedback signal that has this feature.
Add an additional entry to the cirrus,imon device tree property to
allow the IMON scale parameter to be passed.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct some minor errors in the register defaults.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using an external boost supply the PDN_DONE bit is not set, update
the handling in this case to use to use an appropriate fixed delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shorten the time it takes to power down the amp by disabling the volume
ramp whilst doing the final shutdown. The driver has already muted the
amplifier at this stage so doing the volume ramp serves no purpose.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error path in probe attempts to put the device back into reset.
Should we fail to get the reset_gpio (such as a probe defer) we will
leave the error value in there, which the gpiod_set_value_cansleep on
the error path will attempt to deference.
Fix this issue by clearing reset_gpio before we head into the error
path.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver stashes a CODEC pointer in the cs35l35_private structure,
which is used to obtain a struct device pointer for error messages in the
interrupt handler.
However, doing so is not very safe as the interrupt is registered, as it
should be in bus probe, but the CODEC pointer can't be safely stored until
the ASoC level probe. This leaves a window between the two probes where if
any interrupts are received a NULL pointer will be deferenced in the IRQ
handler.
Fix this issue by saving a pointer to the device directly and passing that
to the error messages in the interrupt handler rather than using the CODEC
pointer to access the device pointer.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If cs35l35->pdata.stereo is false then "ret" isn't initialized.
Fixes: 6387f866a2 ("ASoC: Add support for Cirrus Logic CS35L35 Amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove extraneous tab to correct the nesting level indentation
Detected by CoverityScan, CID#1416584 ("Nesting level does
not match indentation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As it is quite common to use a stereo pair of amps but share the IRQ
line between them both add the IRQF_SHARED flag whilst requesting
cs35l35's IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidy up the code a little by adding a local variable for i2c_client->dev
rather than referring to it explicitly everytime.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for setting how the I2S pins are driven in unused slots,
currently the chip will just use the default of drive 0, however this
causes issues when multiple devices are attached to the same bus.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A return statement is missing just before the error paths at the end of
probe. This causes us to fall straight into the error path and disable
the supplies and re-enable reset, as these are only controlled during
probe this causes the part to no longer function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic
CS35L35 9V Boosted Amplifier
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
David Frey