Some targets (eg: msm8994) use the pinctrl framework to configure
interface pins. This change adds support for initialization and
pinctrl active/sleep state control for the HDMI driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DRM device's dev (hdmi->dev->dev) points to the mdss_mdp device
handle. Instead, we should get a reference to the mdss_hdmi
handle.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
That will complete the lists of Alpha + RGB formats.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When the .atomic_commit() handler fails, clean up planes previoulsy
prepared by drm_atomic_helper_prepare_planes() with a call to
drm_atomic_helper_cleanup_planes().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI video mode engine can only take active-high sync signals. This
change prevents MDP5 sending active-low sync signals to DSI in any
case.
Signed-off-by: Hai Li <hali@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
I'm not sure where, exactly, but somewhere in here we must be relying on
an implicit include.
drivers/gpu/drm/msm/dsi/dsi_host.c: In function ‘dsi_host_init_panel_gpios’:
drivers/gpu/drm/msm/dsi/dsi_host.c:1356:2: error: implicit declaration of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
msm_host->disp_en_gpio = devm_gpiod_get(panel_device,
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1356:25: warning: assignment makes pointer from integer without a cast [enabled by default]
msm_host->disp_en_gpio = devm_gpiod_get(panel_device,
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1364:3: error: implicit declaration of function ‘gpiod_direction_output’ [-Werror=implicit-function-declaration]
ret = gpiod_direction_output(msm_host->disp_en_gpio, 0);
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1371:20: warning: assignment makes pointer from integer without a cast [enabled by default]
msm_host->te_gpio = devm_gpiod_get(panel_device, "disp-te");
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1378:3: error: implicit declaration of function ‘gpiod_direction_input’ [-Werror=implicit-function-declaration]
ret = gpiod_direction_input(msm_host->te_gpio);
^
drivers/gpu/drm/msm/dsi/dsi_host.c: In function ‘msm_dsi_host_power_on’:
drivers/gpu/drm/msm/dsi/dsi_host.c:1918:3: error: implicit declaration of function ‘gpiod_set_value’ [-Werror=implicit-function-declaration]
gpiod_set_value(msm_host->disp_en_gpio, 1);
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Also there is a variant to find optional gpios that returns NULL if
there is no gpio instead of -ENOENT.
Make use of both features to simplify the driver.
This makes error checking more strict because errors like -ENOSYS ("no
gpio support compiled in") or -EPROBE_DEFER ("gpio not ready yet") are
handled correctly now.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are different types of PHY from one chipset to another, while
the DSI host controller is relatively consistent across platforms.
Also, the PLL inside PHY is providing the source of DSI byte and
pixel clocks, which are used by DSI host controller. Separated devices
for clock provider and clock consumer make DSI driver better fit into
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change activates PLL driver for DSI to work with
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI byte clock and pixel clocks are sourced from DSI PLL.
This change adds the DSI PLL source clock driver under
common clock framework.
This change handles DSI 28nm PLL only.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
regulator_get() never returns NULL. There's no need for IS_ERR_OR_NULL()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
msm_ioremap() never returns NULL. There's no need for IS_ERR_OR_NULL()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
CRTCs in DSI command mode data path should wait for pingpong done,
instead of vblank, to finish atomic commit.
This change is to enable PP_DONE irq on command mode CRTCs and wait for
this irq happens before atomic commit completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP FLUSH registers could indicate if the previous flush updates
has taken effect at vsync boundary. Making use of this H/W feature
can catch the vsync that happened between CRTC atomic_flush and
*_wait_for_vblanks, to avoid unnecessary wait.
This change allows kms CRTCs to use their own *_wait_for_commit_done
functions to wait for FLUSH register cleared at vsync, before commit
completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
wait_for_completion_timeout returns 0 in case of timeout and never
return < 0 so there is no additional information in printing the
value of time_left here as it will always be 0, thus it can be dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
wait_for_completion_timeout returns >= 0 but never
negative - so the error check should be against equality
to 0 not <= 0.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int, this
patch assigns the return value of wait_for_completion_timeout to an
appropriately typed and named variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some DSI peripherals rely on the HS clock on DSI clock lane as their clock
source. If the clock lane transitions between HS and LP states, it
can disrupt the functioning of such peripherals.
The mipi dsi mode flag MIPI_DSI_CLOCK_NON_CONTINUOUS already exists for
such peripheral drivers. Use it to configure the bit CLKLN_HS_FORCE_REQUEST
in DSI_LANE_CTRL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the GEM object is imported, drm_prime_gem_destroy needs to be
called to clean up dma buffer related information.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Fix build warning when building edp/edp_aux.o due to missing
prototype for edp_aux_transfer.
This function is only used in edp_aux.c so just make it static.
Reported-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
wait_for_completion_timeout returns 0 in case of timeout so printing the
return value here will always yield 0 and is therefor redundant - dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The timeout is passed as a constant which makes it HZ dependent because
jiffies are expected so it should be converted to jiffies. The actual
value is not clear from the code - my best guess is that this should be
300 milliseconds given that other timeouts are in milliseconds based on
looking at other drm drivers (e.g. exynos_drm_dsi.c:356 300ms,
tegra/dpaux.c:188 250ms) - this needs to be confirmed by someone who
knows the details of the driver.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
wait_for_completion_timeout return >= 0 but never negative so the check
logic looks inconsistent. Further the return value of
wait_for_completion_timeout was being passed up the call chain but the
x call sites as drm_dp_i2c_do_msg()/drm_dp_dpcd_access() check for < 0
thus timeout was being treated as success case.
<snip> drivers/gpu/drm/drm_dp_helper.c:drm_dp_i2c_do_msg()
mutex_lock(&aux->hw_mutex);
ret = aux->transfer(aux, msg);
mutex_unlock(&aux->hw_mutex);
if (ret < 0) {
<snip>
logic in edp_aux_transfer() seems incorrect as it could return 0 (timeout)
but checks of <= 0 to indicate error so the return probably should be
-ETIMEDOUT in case wait_for_completion_timeout returns 0 (timeout
occurred).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Seems like disable can race with complete_flip() in process of disabling
a crtc, leading to:
[ 49.065364] Call trace:
[ 49.071441] [<ffffffc00041d5a0>] mdp5_ctl_blend+0x20/0x1c0
[ 49.073788] [<ffffffc00041ebcc>] mdp5_crtc_disable+0x3c/0xa8
[ 49.079348] [<ffffffc0003e7854>] disable_outputs.isra.4+0x11c/0x220
[ 49.085164] [<ffffffc0003e7afc>] drm_atomic_helper_commit_modeset_disables+0x14/0x38
[ 49.091155] [<ffffffc000425c80>] complete_commit+0x40/0xb8
[ 49.099136] [<ffffffc0004260ac>] msm_atomic_commit+0x364/0x398
[ 49.104430] [<ffffffc00040a614>] drm_atomic_commit+0x3c/0x70
[ 49.110249] [<ffffffc0003e67b8>] drm_atomic_helper_set_config+0x1b0/0x3e0
[ 49.116065] [<ffffffc0003f99bc>] drm_mode_set_config_internal+0x64/0xf8
[ 49.122746] [<ffffffc0003fa624>] drm_framebuffer_remove+0xe4/0x128
[ 49.129171] [<ffffffc0003feaf8>] drm_mode_rmfb+0xc0/0x100
[ 49.135420] [<ffffffc0003efba8>] drm_ioctl+0x258/0x4d0
[ 49.140889] [<ffffffc0001b0388>] do_vfs_ioctl+0x338/0x5d0
[ 49.145921] [<ffffffc0001b06a8>] SyS_ioctl+0x88/0xa0
It makes no sense to free the ctl without disabling all stages, so lets
just move them together to avoid the crash.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As found in apq8016 (used in DragonBoard 410c) and msm8916.
Note that numerically a306 is actually 307 (since a305c already claimed
306). Nice and confusing.
Signed-off-by: Rob Clark <robdclark@gmail.com>
A few spots in the driver have support for downstream android
CONFIG_MSM_BUS_SCALING. This is mainly to simplify backporting the
driver for various devices which do not have sufficient upstream
kernel support. But the intentionally dead code seems to cause
some confusion. Rename the #define to make this more clear.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Using fb modifier flag, support NV12MT format in MDP4.
v2:
- rework the modifier's description [Daniel Vetter's comment]
- drop .set_mode_config() callback [Rob Clark's comment]
v3:
- change VENDOR's name and restrict usage to NV12 [pointed by Daniel]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Dump a bit more info when the GPU hangs, without having hang_debug
enabled (which dumps a *lot* of registers). Also dump the scratch
registers, as they are useful for determining where in the cmdstream
the GPU hung (and they seem always safe to read when GPU has hung).
Note that the freedreno gallium driver emits increasing counter values
to SCRATCH6 (to identify tile #) and SCRATCH7 (to identify draw #), so
these two in particular can be used to "triangulate" where in the
cmdstream the GPU hung.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The index of ->planes[] array (3rd parameter) cannot be equal to MAX_PLANE.
This looks like a typo that is now fixed.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In error paths, this was being called without struct_mutex held.
Leading to panics like:
msm 1a00000.qcom,mdss_mdp: No memory protection without IOMMU
Kernel panic - not syncing: BUG!
CPU: 0 PID: 1409 Comm: cat Not tainted 4.0.0-dirty #4
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
Call trace:
[<ffffffc000089c78>] dump_backtrace+0x0/0x118
[<ffffffc000089da0>] show_stack+0x10/0x20
[<ffffffc0006686d4>] dump_stack+0x84/0xc4
[<ffffffc0006678b4>] panic+0xd0/0x210
[<ffffffc0003e1ce4>] drm_gem_object_free+0x5c/0x60
[<ffffffc000402870>] adreno_gpu_cleanup+0x60/0x80
[<ffffffc0004035a0>] a3xx_destroy+0x20/0x70
[<ffffffc0004036f4>] a3xx_gpu_init+0x84/0x108
[<ffffffc0004018b8>] adreno_load_gpu+0x58/0x190
[<ffffffc000419dac>] msm_open+0x74/0x88
[<ffffffc0003e0a48>] drm_open+0x168/0x400
[<ffffffc0003e7210>] drm_stub_open+0xa8/0x118
[<ffffffc0001a0e84>] chrdev_open+0x94/0x198
[<ffffffc000199f88>] do_dentry_open+0x208/0x310
[<ffffffc00019a4c4>] vfs_open+0x44/0x50
[<ffffffc0001aa26c>] do_last.isra.14+0x2c4/0xc10
[<ffffffc0001aac38>] path_openat+0x80/0x5e8
[<ffffffc0001ac354>] do_filp_open+0x2c/0x98
[<ffffffc00019b60c>] do_sys_open+0x13c/0x228
[<ffffffc00019b72c>] SyS_openat+0xc/0x18
CPU1: stopping
But there isn't any particularly good reason to hold struct_mutex for
teardown, so just standardize on calling it without the mutex held and
use the _unlocked() versions for GEM obj unref'ing
Signed-off-by: Rob Clark <robdclark@gmail.com>
During cmd rx, only new versions of H/W provide register to read back
the real number of byte returned by panel. For the old versions, reading
this register will not get the right number. In fact, we only need to
assume the returned data is the same size as we expected, because later
we will check the data type to detect error.
Signed-off-by: Hai Li <hali@codeaurora.org>
drm_mode_connector_attach_encoder() function call is missing
during eDP and DSI connector initialization. As a result,
no encoder is returned by DRM_IOCTL_MODE_GETCONNECTOR system
call. This change is to fix this issue.
Signed-off-by: Hai Li <hali@codeaurora.org>
First of all, we don't want -EPROBE_DEFER when trying to bind children
to cause us to forget to free our vram. And second we don't want vram
allocation fail to trigger _unbind_all() before _bind_all().
Signed-off-by: Rob Clark <robdclark@gmail.com>
When msm_framebuffer_init() fails before calling drm_framebuffer_init(),
drm_framebuffer_cleanup() [called in msm_framebuffer_destroy()]
is still being called even though drm_framebuffer_init() was not
called for that buffer. Thus a NULL pointer derefencing:
[ 247.529691] Unable to handle kernel NULL pointer dereference at virtual address 0000027c
...
[ 247.563996] PC is at __mutex_lock_slowpath+0x94/0x3a8
...
[ 247.823025] [<c07c3c78>] (__mutex_lock_slowpath) from [<c07c3fac>] (mutex_lock+0x20/0x3c)
[ 247.831186] [<c07c3fac>] (mutex_lock) from [<c0347cf0>] (drm_framebuffer_cleanup+0x18/0x38)
[ 247.839520] [<c0347cf0>] (drm_framebuffer_cleanup) from [<c036d138>] (msm_framebuffer_destroy+0x48/0x100)
[ 247.849066] [<c036d138>] (msm_framebuffer_destroy) from [<c036d580>] (msm_framebuffer_init+0x1e8/0x228)
[ 247.858439] [<c036d580>] (msm_framebuffer_init) from [<c036d630>] (msm_framebuffer_create+0x70/0x134)
[ 247.867642] [<c036d630>] (msm_framebuffer_create) from [<c03493ec>] (internal_framebuffer_create+0x67c/0x7b4)
[ 247.877537] [<c03493ec>] (internal_framebuffer_create) from [<c034ce34>] (drm_mode_addfb2+0x20/0x98)
[ 247.886650] [<c034ce34>] (drm_mode_addfb2) from [<c034071c>] (drm_ioctl+0x240/0x420)
[ 247.894378] [<c034071c>] (drm_ioctl) from [<c011df7c>] (do_vfs_ioctl+0x4e4/0x5a4)
...
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[plus initialize msm_fb to NULL to -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current iteration in get_dsi_id_from_intf() is wrong:
instead of iterating until hw_cfg->intf.count, we need to iterate
until MDP5_INTF_NUM_MAX here.
Let's take the example of msm8x16:
hw_cfg->intf.count = 1
intfs[0] = INTF_Disabled
intfs[1] = INTF_DSI
If we stop iterating once i reaches hw_cfg->intf.count (== 1),
we will miss the test for intfs[1].
Actually, this hw_cfg->intf.count entry is quite confusing and is not
(or *should not be*) used anywhere else; let's remove it.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
The DRM_KMS_FB_HELPER config is selected only when DRM_MSM_FBDEV config is
selected. The driver accesses drm_fb_helper_* functions even when legacy fbdev
support is disabled in msm. Wrap around these functions with #ifdef checks to
prevent build break.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Avoid such errors at compilation time:
format '%d' expects argument of type 'int', but argument 3 has type 'size_t'
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Avoid casts from pointers to fixed-size integers to prevent the compiler
from warning. Print virtual memory addresses using %p instead. Also turn
a couple of %d/%x specifiers into %zu/%zd/%zx to avoid further warnings
due to mismatched format strings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
The merge is clean, but the arm build fails afterwards,
due to API changes in the regulator tree.
I've included the patch into the merge to fix the build.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This change adds the support in mdp5 kms driver for single
and dual DSI. Dual DSI case depends on the framework API
and sequence change to support dual data path.
v1: Initial change
v2: Address Rob Clark's comment
- Separate command mode encoder to a new file mdp5_cmd_encoder.c
- Rebase to not depend on msm_drm_sub_dev change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the DSI connector support in msm drm driver.
v1: Initial change
v2:
- Address comments from Archit + minor clean-ups
- Rebase to not depend on msm_drm_sub_dev change [Rob's comment]
v3: Fix issues when initialization is failed
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to add an interface to MDP for connector devices
setting split display information.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to make the content in construct_encoder reflect its
name.
Also, DSI connector may be connected to video mode or command mode
encoder, so that 2 different encoders need to be constructed for DSI.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This TODO can now be removed and replaced by the previous patch
"drm/msm/mdp5: Update headers (add CTL flush bits)"
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some upcoming targets have more bits to set in CTL_FLUSH
registers.
Example: msm8x16 needs to set TIMING1 bit so that some of the
INTF1's interface registers get flushed.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the hw configuration for msm8x16 chipsets in
mdp5_cfg module.
Note that only one external display interface is present in this
configuration (DSI) but has not been enabled yet. It will be enabled
once drm/msm driver supports DSI connectors.
v2: add CTL flush register's hardware mask [pointed by Archit]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SMP blocks are configured for specific client IDs (ports).
These client IDs can be different from one chip to another for a
given pipe.
e.g.: DMA0 pipe fetch Y component is connected to:
- port #10 for MDP5 v1.3
- port #4 for MDP5 v1.6
In order to be compatible for upcoming versions of MDP5, the
client ID list is passed through the MDP5 config module rather
than using a list of hard-coded enum values.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch contains the generated header file of the following
change "drm/msm/mdp5: Get SMP client list from mdp5_cfg".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP block is actually contained inside the MDSS block. For some
chipsets, the base address of the MDP registers is different from the
current (assumed) 0x100 offset.
Like CTL and LM blocks, this changes introduce a dynamic offset
for the MDP instance, which can be found out at runtime, once the
MDSS HW version is read.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change contains the generated header file for the following
change "drm/msm/mdp5: Separate MDP5 domain from MDSS domain".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The width and height in SSPP_SRC_IMG_SIZE register should be the
size of the entire source framebuffer, not the fetch size.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the registers in mdp5 ping pong blocks
and split display control registers.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pingpong register base addresses are different across platforms.
This change adds this information to config table and initialize
the values for 8x74 and 8084.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Up until now, we assume that eDP is tight to intf_0 and HDMI to
intf_3. This information shall actually come from the mdp5_cfg
module since it can change from one chip to another.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
v3: add sanity check before writing in INTF_TIMING_ENGINE_EN registers
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some interfaces (WB, DSI Command Mode) need to be kicked off
through a START Signal. This signal needs to be sent at the right
time and requests in some cases to keep track of the pipeline
status (eg: whether pipeline registers are flushed AND output WB
buffers are ready, in case of WB interface).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI and WB interfaces need a more complex pipeline configuration
than the current mdp5_ctl_set_intf().
For example, memory output connections need to be selected for
WB. Interface mode (Video vs. Command modes) also need to be
configured for DSI.
This change takes care of configuring the whole pipeline as far
as operation mode goes. DSI and WB interfaces will be added
later.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[Remove temp bisectability hack -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Prepare for pipeline operation mode configuration, in particular
for DSI and WB modes.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[Throw in a #define temporarily to keep things bisectable -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 hardware has some limitation and requires to avoid flushing
registers more than once between two Vblanks.
This change removes all FLUSH operations (except for HW cursor)
beside the one coming from a CRTC's ->atomic_flush().
This avoid this type of behavior (eg: CRTC + 1 plane overlay):
[drm:mdp5_crtc_vblank_irq] vblank
[drm:mdp5_ctl_commit] flush (20048) CTL + LM0 + RGB0
[drm:mdp5_ctl_commit] flush (20040) CTL + LM0
[drm:mdp5_crtc_vblank_irq] blank
[drm:mdp5_ctl_commit] flush (20049) CTL + LM0 + RGB0 + VIG0
[drm:mdp5_crtc_vblank_irq] blank
and replaces it by:
[drm:mdp5_crtc_vblank_irq] vblank
[drm:mdp5_ctl_commit] flush (20048) CTL + LM0 + RGB0
[drm:mdp5_crtc_vblank_irq] blank
[drm:mdp5_ctl_commit] flush (20049) CTL + LM0 + RGB0 + VIG0
[drm:mdp5_crtc_vblank_irq] blank
Only *one* FLUSH is called between Vblanks interrupts.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support to use the VRAM carveout (if specified in dtb) for fbdev
scanout buffer. This allows drm/msm to take over a bootloader splash-
screen, and avoids corruption on screen that results if the kernel uses
memory that is still being scanned out for itself.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We'll want to extend this a bit to handle also a reserved-memory
("stolen") region, so that drm/msm can take-over bootloader splash
screen. First split it out into it's own fxn to reduce noise in
the following patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
Use cases like rotation require these hooks to have some context so they
know how to prepare and cleanup the frame buffer correctly.
For i915 specifically, object backing pages need to be mapped differently
for different rotation modes and the driver needs to know which mapping to
instantiate and which to tear down when transitioning between them.
v2: Made passed in states const. (Daniel Vetter)
[airlied: add mdp5 and atmel fixups]
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In kexec environment, we are more likely to encounter irq's already
enabled from previous environment. At which point we find that writes
to disable/clear pending irq's are slightly less than useless without
first enabling clocks.
TODO: full blown state read-in so kexec'd kernel can inherit the mode
already setup.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Seems like we just want BLEND_EN and not BLEND_TRANSP_EN (setting the
latter results in black pixels in the cursor image treated as
transparent).
Signed-off-by: Rob Clark <robdclark@gmail.com>
If cursor is set near the edge of the screen, it is not valid to use the
new cursor width/height as the ROI dimensions. Split out the ROI calc
and use it both cursor_set and cursor_move.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the atomic commit fails due to completion wait interruption the
atomic commit object is not freed and is thus leaked. Free it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When a CRTC is disabled, no CTL is allocated to it (CRTC->ctl == NULL);
in that case we should not try to FLUSH registers and do nothing instead.
This can happen when we try to move a cursor but the CRTC's CTL
(CONTROL) has not been allocated yet (inactive CRTC).
It can also happens when we .atomic_check()/.atomic_flush() on a
disabled CRTC.
A CTL needs to be kept as long as the CRTC is alive. Releasing it
after the last VBlank is safer than in .atomic_flush().
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some target have up to 6 layer mixers (LM).
Let the header file access the last LM's base address.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Commit 0b776d457b ("drm/msm: fix fallout of atomic dpms
changes") has a typo in both mdp5_encoder_helper_funcs and
mdp5_crtc_helper_funcs definitions:
.dpms entry should be replaced by .disable and .enable
Also fixed a typo in mdp5_encoder_enable().
Note that these typos are only present for MDP5. MDP4 is fine.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These names only make sense because of backwards compatability with
the order used by the crtc helper library. There's not really any real
requirement in the ordering here.
So rename them to something more descriptive and update the kerneldoc
a bit. Motivated in a discussion with Laurent about how to restore
plane state for dpms for drivers with runtime pm.
v2: Squash in fixup from Stephen Rothwell to fix a conflict with
tegra.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Useful to avoid recompiling to disable fbdev. Useful because otherwise
the first modeset happens under console_lock (ie. debugging sadness).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Combining -Werror with all the extra warning flags that W=1 adds doesn't
go so well. Especially because some of the warnings triggered are from
included headers. So just drop -Werror.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case we request a number of SMP blocks which is lower than
the already reserved blocks, we should not try to allocate a
negative number, but 0 blocks instead.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
So after clarification from qcom, it seems mdp4 and mdp5 support
*de*interlacing but not generating an interlaced signal. Which would
explain why interlaced modes never worked properly.
So disable in the one connector which was claiming to support
interlaced.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The gnome-shell wayland compositor triggers a setcrtc with an fb that is
still being rendered, triggering the call to _wait_fence_interruptable().
But a NULL timeout means "don't wait, return -EBUSY if not ready", which
in turn causes the setcrtc to fail.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch implements the hardware accelarated cursor
support for MDP5 platforms.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In the same idea mdp5_cfg was added, this change allows us to quickly
add new instances, such as apq8084's HDMI in this case.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change add the regulator/clock configuration for MDP5 v1.3.
This config is close to the one already existing for 8x74, except
that one more regulator is needed (hpd-5v-en).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of reporting BUG_ON when resources arrays are not
dimensioned correctly, this patch does a dynamic allocation of
these arrays. This is needed for the following patches that add a
regulator for a new target.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_ctl_set_intf()'s second argument should be "int", not "enum mdp5_intf".
The passed in value is "intf", not "intf_id".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Modified the hard-coded hdmi connector/encoder implementations in msm drm
driver to support both edp and hdmi.
V1: Initial change
V2: Address Thierry's change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds a new eDP connector in msm drm driver. With this
change, eDP panel can work with msm platform under drm framework.
v1: Initial change
v2: Address Rob's comments
Use generated header file for register definitions
Change to devm_* APIs
v3: Address Thierry's comments and rebase on top of atomic changes
Remove edp_bridge_mode_fixup
Remove backlight control code and rely on pwm-backlight
Remove continuous splash screen support for now
Change to gpiod_* APIs
v4: Fix kbuild test issue
Signed-off-by: Hai Li <hali@codeaurora.org>
[robclark: v5: rebase on drm_bridge changes in drm-next]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The patch add support for YUV frame format
for MDP4 platform.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the NV12 format support for public planes.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Both MDP4 and MDP5 share some code as far as YUV support is
concerned. This change adds this information and will be followed
by the actual MDP4 and MDP5 YUV support patches.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Resync from rnndb database, to pull in register defines for:
* eDP
* HDMI/HDCP
* mdp4/mdp5 YUV support
* mdp5 hw cursor support
Signed-off-by: Rob Clark <robdclark@gmail.com>
On !SMP systems spinlocks do not exist. Thus checking of they
are active will always fail.
Use
assert_spin_locked(lock);
instead of
BUG_ON(!spin_is_locked(lock));
to not BUG() on all UP systems.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
[robclark: drop stray ')']
Signed-off-by: Rob Clark <robdclark@gmail.com>
3d3f8b1f8b ("drm/bridge: make bridge registration independent of drm
flow") resulted that the hdmi bridge object would be leaked at teardown.
Just switch over to devm_kzalloc() as the easy way to solve this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As a result of atomic DPMS support, the various prepare/commit hooks get
called in a way that msm dislikes. We were expecting prepare/commit to
bracket a modeset, which is no longer the case. This was needed to hold
various extra clk's (such as interface clks) on while we are touching
registers, and in the case of mdp4 holding vblank enabled.
The most straightforward way to deal with this, since we already have
our own atomic_commit(), is to just handle prepare/commit internally to
the driver (with some additional vfuncs for mdp4 vs mdp5), and switch
everything over to instead use the new enable/disable hooks. It doesn't
really change too much, despite the code motion. What used to be in the
encoder/crtc dpms() fxns is split out into enable/disable.
We should be able to drop our own enable-state tracking, as the atomic
helpers should do this for us. But keeping that for the short term for
extra debugging as atomic stablizes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Stephane Viau