Although on HSW/BDW there is only a single display global power well,
it's programmed the same way as other GEN9+ power wells. This also
means we can get at the HSW/BDW request and status flags the same way
it's done on GEN9+ by assigning the corresponding HSW/BDW power well ID.
This ID was assigned in a recent patch, so we can now switch to using
the same macros everywhere on HSW+.
Updating the HSW power well control register with RMW is not strictly
necessary, but this will allow us to use the same code for GEN9+.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-13-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add an ID for the HSW/BDW global display power well for consistency. The
ID is selected so that it can be used to get at the HW request and
status flags with the corresponding GEN9+ macros. Unifying the HSW/BDW
and GEN9+ versions of these macros and the power well ops using them
will be done in follow-up patches.
v2:
- Rebased on v2 of patch 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-3-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the I830 power well ID assignment explicit for consistency.
v2:
- s/GEN2/I830/ in the comment, since other GEN2s don't have the power
well. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-2-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, the power well IDs are defined in separate platform specific enums,
which isn't ideal for the following reasons:
- the IDs are used by helpers like lookup_power_well() in a platform
independent way
- the always-on power well is used by multiple platforms and so needs
now separate IDs, although these IDs refer to the same thing
To make things more consistent use a single enum instead of the two
separate ones, listing the IDs per platform (or set of very similar
platforms like all GEN9/10). Replace the separate always-on power
well IDs with a single ID.
While at it also add a note clarifying the distinction between regular
power wells that follow a common programming pattern and custom ones
that are programmed in some other way. The IDs for regular power wells
need to stay fixed, since they also define the request and state HW flag
positions in their corresponding power well control register(s).
v2:
- Add comment about id to req,status bit mapping to the enum. (Rodrigo)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power well IDs are used for lookup, so they must be unique on a
given platform; ensure this on CHV. This didn't cause an actual problem
since we didn't need to look up power wells which happened to share an
ID.
Mark this new power well as custom, since its programming pattern
doesn't follow that of the rest of VLV/CHV power wells.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-2-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PLLs are the source clocks for the DDIs so in order
to determine the ddi clock we need to check the PLL
configuration.
v2: Mika pointed out that 24 was hardcoded while it
should consider ref clock that can be either 24KHz
or 19.2KHz on CNL.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499374321-31152-1-git-send-email-rodrigo.vivi@intel.com
The Cursor Coeff is lower 6 bits in the PORT_TX_DW4 register
and hence the CURSOR_COEFF_MASK should be (0x3F << 0)
Fixes: 04416108cc ("drm/i915/cnl: Add registers related to voltage
swing sequences.")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498785241-21138-1-git-send-email-manasi.d.navare@intel.com
Paulo noticed that we were missing few bits clear
before writing values back to the register on
these RMW MMIO operations.
v2: Remove "POST_" from CURSOR_COEFF_MASK. (Paulo).
v3: Remove unnecessary braces. (Jani).
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497897572-22520-1-git-send-email-rodrigo.vivi@intel.com
Enables access to OA unit metrics for BDW, CHV, SKL and BXT which all
share (more-or-less) the same OA unit design.
Of particular note in comparison to Haswell: some OA unit HW config
state has become per-context state and as a consequence it is somewhat
more complicated to manage synchronous state changes from the cpu while
there's no guarantee of what context (if any) is currently actively
running on the gpu.
The periodic sampling frequency which can be particularly useful for
system-wide analysis (as opposed to command stream synchronised
MI_REPORT_PERF_COUNT commands) is perhaps the most surprising state to
have become per-context save and restored (while the OABUFFER
destination is still a shared, system-wide resource).
This support for gen8+ takes care to consider a number of timing
challenges involved in synchronously updating per-context state
primarily by programming all config state from the cpu and updating all
current and saved contexts synchronously while the OA unit is still
disabled.
The driver intentionally avoids depending on command streamer
programming to update OA state considering the lack of synchronization
between the automatic loading of OACTXCONTROL state (that includes the
periodic sampling state and enable state) on context restore and the
parsing of any general purpose BB the driver can control. I.e. this
implementation is careful to avoid the possibility of a context restore
temporarily enabling any out-of-date periodic sampling state. In
addition to the risk of transiently-out-of-date state being loaded
automatically; there are also internal HW latencies involved in the
loading of MUX configurations which would be difficult to account for
from the command streamer (and we only want to enable the unit when once
the MUX configuration is complete).
Since the Gen8+ OA unit design no longer supports clock gating the unit
off for a single given context (which effectively stopped any progress
of counters while any other context was running) and instead supports
tagging OA reports with a context ID for filtering on the CPU, it means
we can no longer hide the system-wide progress of counters from a
non-privileged application only interested in metrics for its own
context. Although we could theoretically try and subtract the progress
of other contexts before forwarding reports via read() we aren't in a
position to filter reports captured via MI_REPORT_PERF_COUNT commands.
As a result, for Gen8+, we always require the
dev.i915.perf_stream_paranoid to be unset for any access to OA metrics
if not root.
v5: Drain submitted requests when enabling metric set to ensure no
lite-restore erases the context image we just updated (Lionel)
v6: In addition to drain, switch to kernel context & update all
context in place (Chris)
v7: Add missing mutex_unlock() if switching to kernel context fails
(Matthew)
v8: Simplify OA period/flex-eu-counters programming by using the
batchbuffer instead of modifying ctx-image (Lionel)
v9: Back to updating the context image (due to erroneous testing,
batchbuffer programming the OA unit doesn't actually work)
(Lionel)
Pin context before updating context image (Chris)
Drop MMIO programming now that we switch to a kernel context with
right values in initial context image (Chris)
v10: Just pin_map the contexts we want to modify or let the
configuration happen on first use (Chris)
v11: Update kernel context OA config through the batchbuffer rather
than on the fly ctx-image update (Lionel)
v12: Rework OA context registers update again by swithing away from
user contexts and reconfiguring the kernel context through the
batchbuffer and updating all the other contexts' context image.
Also take care to lock slice/subslice configuration when OA is
on. (Lionel)
v13: Request rpcs updates on all engine when updating the OA config
(Lionel)
v14: Drop any kind of rpcs management now that we monitor sseu
configuration changes in a later patch (Lionel)
Remove usleep after programming the NOA configs on Gen8+, this
doesn't seem to be needed (Lionel)
v15: Respect coding style for block comments (Chris)
v16: Add missing i915_add_request() in case we fail to emit OA
configuration (Matthew)
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com> \o/
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.
This new sequence for Cannonlake is more like Broxton style
but still with different registers, different table and
different steps.
v2: Do not write to DW4_GRP to avoid overwrite individual loadgen.
Fix PORT_CL_DW5 SUS Clock Config set.
v3: As previous platforms use only eDP table if low voltage was
requested.
v4: fix Werror:maybe uninitialized (Paulo)
v5: Rebase on top of dw2_swing_sel changes
on previous patches.
v6: Using flexible SCALING_MODE_SEL(x).
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-11-git-send-email-rodrigo.vivi@intel.com
This are the registers and bits needed for the voltage swing
sequence on Cannonlake.
v2: Remove CL_DW5 that was wrongly defined.
v3: Use (1 << 1) instead of (1<<1) as Paulo suggested
Change DW2 swing sel upper and lower macros to do the
bit selection instead of definint a table that doesn't
match the spec. It is based on a Manasi version of it.
Credits-to: Manasi.
v4: Let SCALING_MODE_SEL flexible. (Manasi)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-9-git-send-email-rodrigo.vivi@intel.com
Also new registers can have different mmio offsets
per different lane per port.
v2: Use _PICK as PORT3 instead of creating a new
macro with if per port.
v3: Use _PICK directly on MMIO_PORT6. While MMIO_PORT
isn't flexible enough let's continue with MMIO_PORT6
as we have MMIO_PORT3.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-8-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Although CNL follows PLL initialization more like Skylake
than Broxton we have a completely different initialization
sequence and registers used.
One big difference from SKL is that CDCLK PLL is now
exclusive (ADPLL) and for DDIs and MIPI we need to use
DFGPLLs 0, 1 or 2.
v2: Accept all Ander's suggestions and fixes:
- Registers and bits names prefix
- Group pll functions
- bits masks fixes
- remove read and modify on cfgcr1
- fix cfgcr0 setup
v3: Set SSC_ENABLE for DP.
Fix HDMI_MODE cfgcr0.
Avoid touch cfgcr0 on DP.
Add missed else on dpll_mgr definition so we use cnl one, not hsw.
v3: Centra freq should be always set to default and change bits
definitions to (1 << 1) instead of (1<<1). (by Paulo)
v4: Rebased.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-7-git-send-email-rodrigo.vivi@intel.com
One of the steps for PLL (un)initialization is to (un)map
the correspondent DDI that is actually using that PLL.
So, let's do this step following the places already stablished
and used so far, although spec put this as part of PLL
initialization sequences.
v2: Use proper prefix on bits names as suggested by Ander.
v3: Add missed "~". Without that the logic was inverted
so we were disabling interrupts.
Credits-to: Clinton
Credits-to: Art
v4: Spec is getting updated to do DDI -> PLL mapping
and clock on in 2 separated reg writes. (Paulo)
Also update bits definitions to use space
(1 << 1) instead of (1<<1). (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-5-git-send-email-rodrigo.vivi@intel.com
Implement the CNL display init/uninit sequence as outlined in Bspec.
Quite similar to SKL/BXT. The main complicaiton is probably the extra
procmon setup we must do based on the process/voltage information we
can read out from some register.
v2: s/skl_dbuf/gen9_dbuf/ to follow upstream
bxt needed a cdclk sanitize step, so let's add it for cnl too
v3: s/CHICKEN_MISC_1/CHICKEN_MISC_2/ (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework
v5: Removed unecessary Aux IO forced enable/disable, Fix DW10 setup
Fix procpon Mask. (Credits-to Paulo and Clint)
Remove A0 workaround.
v6: Rebased on top of recent code (Rodrigo).
v7: Respect the order of sanitize_ after set_
(Done by Rodrigo, Requested by Ville)
v8: Commit message updated to matvh v5 changes besides
Remove unused DW8 and an extra blank line. (all noticed
by Imre).
v9: Remove __attribute__((unused)) added on latest version
of drm/i915/cnl: Implement .set_cdclk() for CNL.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-3-git-send-email-rodrigo.vivi@intel.com
Add support for reading out the cdclk frequency from the hardware on
CNL. Very similar to BXT, with a few new twists and turns:
* the PLL is now called CDCLK PLL, not DE PLL
* reference clock can be 24 MHz in addition to the 19.2 MHz BXT had
* the ratio now lives in the PLL enable register
* Only 1x and 2x CD2X dividers are supported
v2: Deal with PLL lock bit the same way as BXT/SKL do now
v3: DSSM refclk indicator is bit 31 not 24 (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework.
v5: Set cdclk to the ref clock as previous platforms. (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-1-git-send-email-rodrigo.vivi@intel.com
Let's be picky and just use PICK directly.
So we can extend this later without creating
a new PORT_X por every new number of ports we
have to handle.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496700722-13755-1-git-send-email-rodrigo.vivi@intel.com
CNL power wells are very similar to SKL, with the exception that the
misc IO well has been split into separate AUX IO wells.
Not sure if DMC is supposed to manage the AUX wells for us or not.
Let's assume so for now.
v2: DDI A power well wants DDI A domains, not DDI B domains
v3: s/BIT/BIT_ULL and add proper Aux IO domains. (Rodrigo)
v4: Remove PW_DDI_E. Not supported on Current CNL SKUs. (Rodrigo).
v5: Removed DDI_E_IO_DOMAINS and moved PORT_DDI_E_IO to DDI_A_IO
for the same reasons as v4 when we found out that current CNL
SKUs don't have the full port E split.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-10-git-send-email-rodrigo.vivi@intel.com
The number of compressed segments has been available ever since
FBC2 was introduced in g4x, it just moved from the STATUS register
into STATUS2 on IVB.
For FBC1 if we really wanted the number of compressed segments we'd
have to trawl through the tags, but in this case since the code just
uses the number of compressed segments as an indicator whether
compression has occurred we can just check the state of the
COMPRESSING and COMPRESSED bits. IIRC the hardware will try to
periodically recompress all uncompressed lines even if they haven't
changed and the COMPRESSED bit will be cleared while the compressor
is running, so just checking the COMPRESSED bit might not give us
the right answer. Hence it seems better to check for both
COMPRESSED and COMPRESSING as that should tell us that the
compressor is at least trying to do something.
While at it move the IVB+ register define to the right place, unify
the naming convention of the compressed segment count masks, and
fix up the mask for g4x.
v2: s/ILK_DPFC_STATUS2/IVB_FBC_STATUS2/ (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk> # SNB
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # ilk+
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # pre-ilk
Link: http://patchwork.freedesktop.org/patch/msgid/20170606124318.31755-1-ville.syrjala@linux.intel.com
On CNP PCH based platforms the gmbus is on the south display that
is on PCH. The existing implementation for previous platforms
already covers the need for CNP expect for the pin pair configuration
that follows similar definitions that we had on BXT.
v2: Don't drop "_BXT" as the indicator of the first platform
supporting this pin numbers. Suggested by Daniel.
v3: Add missing else and fix register table since CNP GPIO_CTL
starts on 0xC5014.
v4: Fix pin number and map according to the current available VBT.
Re-add pin 4 for port D. Lost during some rebase.
v5: Use table as spec. If VBT is wrong it should be ignored.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-5-git-send-email-rodrigo.vivi@intel.com
RAWCLK_FREQ register has changed for platforms with CNP+.
[29:26] This field provides the denominator for the fractional
part of the microsecond counter divider. The numerator
is fixed at 1. Program this field to the denominator of
the fractional portion of reference frequency minus one.
If the fraction is 0, program to 0.
0100b = Fraction .2 MHz = Fraction 1/5.
0000b = Fraction .0 MHz.
[25:16] This field provides the integer part of the microsecond
counter divider. Program this field to the integer portion
of the reference frequenct minus one.
Also this register tells us that proper raw clock should be read
from SFUSE_STRAP and programmed to this register. Up to this point
on other platforms we are reading instead of programming it so
probably relying on whatever BIOS had configured here.
Now on let's follow the spec and also program this register
fetching the right value from SFUSE_STRAP as Spec tells us to do.
v2: Read from SFUSE_STRAP and Program RAWCLK_FREQ instead of
reading the value relying someone else will program that
for us.
v3: Add missing else. (Jani)
v4: Addressing all Ville's catches:
Use macro for shift bits instead of defining shift.
Remove shift from the cleaning bits with mask that already
has it.
Add missing I915_WRITE to actually write the reg.
Stop using useless DIV_ROUND_* on divider that is exact
dividion and use DIV_ROUND_CLOSEST for the fraction part.
v5: Remove useless Read-Modify-Write on raclk_freq reg. (Ville).
v6: Change is per PCH instead of per platform.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-3-git-send-email-rodrigo.vivi@intel.com
This is a follow-up patch to the previous patch ([PATCH[1/2] drm/i915:
Disable decoupled MMIO) to remove the dead code for decoupled MMIO
implementation, as it won't be used any longer on GEN9LP.
Therefore, this patch reverts:
commit 85ee17ebee
Author: Praveen Paneri <praveen.paneri@intel.com>
Date: Tue Nov 15 22:49:20 2016 +0530
drm/i915/bxt: Broxton decoupled MMIO
Signed-off-by: Kai Chen <kai.chen@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170523215812.18328-3-kai.chen@intel.com
This commit fixes the following compiler warning:
drivers/gpu/drm/i915/intel_dsi.c: In function ‘intel_dsi_prepare’:
drivers/gpu/drm/i915/intel_dsi.c:1487:23: warning:
?: using integer constants in boolean context [-Wint-in-bool-context]
PORT_A ? PORT_C : PORT_A),
Fixes: f4c3a88e5f ("drm/i915: Tighten mmio arrays for MIPI_PORT")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170518110644.9902-1-hdegoede@redhat.com
IVB introduced the CUR_FBC_CTL register which allows reducing the cursor
height down to 8 lines from the otherwise square cursor dimensions.
Implement support for it. CUR_FBC_CTL can't be used when the cursor
is rotated.
Commandeer the otherwise unused cursor->cursor.size to track the
current value of CUR_FBC_CTL to optimize away redundant CUR_FBC_CTL
writes, and to notice when we need to arm the update via CURBASE if
just CUR_FBC_CTL changes.
v2: Reverse the gen check to make it sane
v3: Only enable CUR_FBC_CTL when cursor is enabled, adapt to
earlier code changes which means we now actually turn off
the cursor when we're supposed to unlike v2
v4: Add a comment about rotation vs. CUR_FBC_CTL,
rebase due to 'dirty' (Chris)
v5: Rebase to the atomic world
Handle 180 degree rotation
Add HAS_CUR_FBC()
v6: Rebase
v7: Rebase due to I915_WRITE_FW/uncore.lock
s/size/fbc_ctl/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Turns out our skills in decoding the CLKCFG register weren't good
enough. On this particular elk the answer we got was 400 MHz when
in reality the clock was running at 266 MHz, which then caused us
to program a bogus AUX clock divider that caused all AUX communication
to fail.
Sadly the docs are now in bit heaven, so the fix will have to be based
on empirical evidence. Using another elk machine I was able to frob
the FSB frequency from the BIOS and see how it affects the CLKCFG
register. The machine seesm to use a frequency of 266 MHz by default,
and fortunately it still boot even with the 50% CPU overclock that
we get when we bump the FSB up to 400 MHz.
It turns out the actual FSB frequency and the register have no real
link whatsoever. The register value is based on some straps or something,
but fortunately those too can be configured from the BIOS on this board,
although it doesn't seem to respect the settings 100%. In the end I was
able to derive the following relationship:
BIOS FSB / strap | CLKCFG
-------------------------
200 | 0x2
266 | 0x0
333 | 0x4
400 | 0x4
So only the 200 and 400 MHz cases actually match how we're currently
decoding that register. But as the comment next to some of the defines
says, we have been just guessing anyway.
So let's fix things up so that at least the 266 MHz case will work
correctly as that is actually the setting used by both the buggy
machine and my test machine.
The fact that 333 and 400 MHz BIOS settings result in the same register
value is a little disappointing, as that means we can't tell them apart.
However, according to the gmch datasheet for both elk and ctg 400 Mhz is
not even a supported FSB frequency, so I'm going to make the assumption
that we should decode it as 333 MHz instead.
Cc: stable@vger.kernel.org
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100926
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504181530.6908-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Pre-calculate engine context size based on engine class and device
generation and store it in the engine instance.
v2:
- Squash and get rid of hw_context_size (Chris)
v3:
- Move after MMIO init for probing on Gen7 and 8 (Chris)
- Retained rounding (Tvrtko)
v4:
- Rebase for deferred legacy context allocation
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: intel-gvt-dev@lists.freedesktop.org
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
In such a way that vcs and vcs2 are just two different instances (0 and 1)
of the same engine class (VIDEO_DECODE_CLASS).
v2: Align the instance types (Tvrtko)
v3: Don't use enums for bspec-defined stuff (Michal)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491834873-9345-2-git-send-email-oscar.mateo@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
We have used cz timestamp register to gain a reference time wrt
to residency calculations. The residency counts are in cz clk ticks
(333Mhz clock) but for some reason the cz timestamp register gives
100us units. Perhaps for some other usage, the base-ten based values
are easier, but in residency calculations raw units would have been
the easiest.
As there is not much advantage of using base-ten clock through
a more costly punit access, take our reference times directly from
kernel clock.
v2: use ktime (Chris, Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The REDIRECT_TO_GUC bit is a strange beast as it is a disable bit -
setting the bit in the pm interrupt generation stops the interrupt going
to the guc (not sending it to the guc as the name implies). To help the
reader rename it to DISABLE_REDIRECT_TO_GUC so that we keep the bspec
greppable name without it being as confusing!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170312132745.9618-1-chris@chris-wilson.co.uk
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Driver needs to ensure that it doesn't mask the PM interrupts, which are
unmasked/needed by GuC firmware. For that, Driver maintains a bitmask of
interrupts to be kept unmasked, pm_intr_keep.
pm_intr_keep was determined across GuC load. GuC gets loaded in different
scenarios and it is not going to change the pm_intr_keep so this patch
moves its setup to intel_irq_init.
This patch fixes incorrect RPS masking leading to UP interrupts triggered
even when at cur_freq=max and inversly for Down interrupts.
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488862355-9768-1-git-send-email-sagar.a.kamble@intel.com
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
Generally we are using macros for any hardware identifiers as these
may change between Gens. Do the same with hardware engine ids.
v2: move hw engine defs to i915_reg.h (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301202615.118632-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drivers/gpu/drm/i915/intel_dsi.c: In function ‘intel_dsi_prepare’:
drivers/gpu/drm/i915/intel_dsi.c:1308:1: error: the frame size of 2488 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
which is caused by the compiling expanding every _MIPI_PORT into an
on-stack array of u32[3] at every callsite. Not sure why only one
machine/compiler appears susceptible, but with a minor tweak to _MIPI_PORT
we can defer the error until later.
This is a partial revert of commit ce64645d86 ("drm/i915: use variadic
macros and arrays to choose port/pipe based registers") for a particular
bad offender.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228145519.18012-1-chris@chris-wilson.co.uk
Acked-by: Jani Nikula <jani.nikula@intel.com>
v2: Addressed Jani's Review comments(renamed bit field macros)
Txesc clock divider is calculated and programmed
for geminilake platform.
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-7-git-send-email-madhav.chauhan@intel.com
PLL divider range for GLK is different than that of
BXT, hence adding the GLK range check in this patch.
v2: Code restructure using min and max ratio variables (Ander)
v3: Code changes to avoid "maybe-uninitialized" warning (Jani)
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-5-git-send-email-madhav.chauhan@intel.com
Program the clk lane and tlpx time count registers
to configure DSI PHY.
v2: Addressed Jani's Review comments(renamed bit field macros)
v3: Program clk lane timing reg same as dphy param reg.
v4: Removed "line over 80 character" warning
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-3-git-send-email-madhav.chauhan@intel.com
-----BEGIN PGP SIGNATURE-----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=Yjfg
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
Following a reset, the context and page directory registers are lost.
However, the queue of requests that we resubmit after the reset may
depend upon them - the registers are restored from a context image, but
that restore may be inhibited and may simply be absent from the request
if it was in the middle of a sequence using the same context. If we
prime the CCID/PD registers with the first request in the queue (even
for the hung request), we prevent invalid memory access for the
following requests (and continually hung engines).
v2: Magic BIT(8), reserved for future use but still appears unused.
v3: Some commentary on handling innocent vs guilty requests
v4: Add a wait for PD_BASE fetch. The reload appears to be instant on my
Ivybridge, but this bit probably exists for a reason.
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207152437.4252-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit c0dcb203fb)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Once the address space has been created (using 3 or 4 levels of page
tables), we should use that to program the appropriate type into the
contexts. This gives us the flexibility to handle different types of
address spaces at runtime.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170209144036.23664-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Following a reset, the context and page directory registers are lost.
However, the queue of requests that we resubmit after the reset may
depend upon them - the registers are restored from a context image, but
that restore may be inhibited and may simply be absent from the request
if it was in the middle of a sequence using the same context. If we
prime the CCID/PD registers with the first request in the queue (even
for the hung request), we prevent invalid memory access for the
following requests (and continually hung engines).
v2: Magic BIT(8), reserved for future use but still appears unused.
v3: Some commentary on handling innocent vs guilty requests
v4: Add a wait for PD_BASE fetch. The reload appears to be instant on my
Ivybridge, but this bit probably exists for a reason.
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207152437.4252-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
The audio chicken bit (register offset 0x62f38) seems required to make
DP audio working on some machines. At least, on Dell Wyse 3040, I
failed to get the audio unless this bit is set once.
Strangely, the bit seems necessary only once, and it persists after
that, even some power-off cycles. The register is supposedly
write-only, so it's no evidence whether the bit keeps effect
persistently. But, judging from the experiment, it looks enough to
set it up once at the device initialization.
The patch is basically a cut from the original patch by Pierre-Louis
Bossart.
v1->v2: drop read since it's a write-only reg.
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable unmute/mute amp notification. This doesn't seem to affect
HDMI support so this is done unconditionally.
An earlier version of this patch set a chicken bit at address 0x62F38
prior to the mute/unmute but this register doesn't seem to do anything
so this phase was removed.
v1->v2: Drop needless pipe A check, avoid temporary reg offset variable.
v2->v3: Add "_" prefix to VLV_AUD_PORT_EN_X_DBG as they are internal.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable MIPI IO WA for BXT DSI as per bspec and
program the DSI regulators.
v2: Moved IO enable to pre-enable as per Mika's
review comments. Also reused the existing register
definition for BXT_P_CR_GT_DISP_PWRON.
v3: Added Programming the DSI regulators as per disable/enable
sequences.
v4: Restricting regulator changes to BXT as suggested by
Jani/Mika
v5: Removed redundant read/modify for regulator register as
per Jani's comment. Maintain enable/disable symmetry as per spec.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Acked-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485353603-11260-1-git-send-email-vidya.srinivas@intel.com
This allows the use of more than 3 ports/pipes/whatever without tricks,
even if the register offsets are not evenly spaced.
There's the risk of out of bounds access if we're not careful; currently
that would "just" lead to the wrong register offset being used. It might
be possible to add build bug ons for build time constant indexing.
We already have ports defined up to E, not sure if we might have bugs
related to them and the current _PORT3() macro.
text data bss dec hex filename
1239868 46199 4096 1290163 13afb3 drivers/gpu/drm/i915/i915.ko
1238828 46199 4096 1289123 13aba3 drivers/gpu/drm/i915/i915.ko
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485532626-20923-1-git-send-email-jani.nikula@intel.com
Move the invariant parts of context desc setup from execlist init
to context creation. This is advantageous when we need to
create different templates based on the context parametrization,
ie. for svm capable contexts.
v2: s/create/default, remove engine->ctx_desc_template
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485522189-31984-1-git-send-email-mika.kuoppala@intel.com
The gamma tables in Geminilake were changed. There is no split-gamma
mode. Instead, there is a dedicated degamma table that is enabled
whenever pipe CSC is enabled.
The dedicated gamma table has 16 bit precision but doesn't support
separate channels. Since that doesn't match the per-channel format of
the degamma LUT property, for now only a linear table is loaded and the
property ignored.
v2: Remove empty line. (Ville)
Reuse broadwell code. (Ville)
v3: Don't write PIPE_CSC_MODE. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127090230.20302-1-ander.conselvan.de.oliveira@intel.com
In Geminilake, the bits for enabling pipe csc, pipe gamma and plane
gamma moved to a new register. So update the plane update functions
to set the right bits.
Pipe CSC is kept disabled though, since enabling that also enables the
dedicated degamma table, and that is not properly programmed yet,
leading to a black screen.
v2: Use plane_id. (Ville)
Remove unnecessary variable. (Ville)
Keep registers in offset order. (Ville)
Don't set plane gamma disable twice. (Ander)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485429865-10687-3-git-send-email-ander.conselvan.de.oliveira@intel.com
Enable support for HDMI LPE audio mode on Baytrail and
Cherrytrail when HDaudio controller is not detected
Setup minimum required resources during i915_driver_load:
1. Create a platform device to share MMIO/IRQ resources
2. Make the platform device child of i915 device for runtime PM.
3. Create IRQ chip to forward HDMI LPE audio irqs.
HDMI LPE audio driver (a standalone sound driver) probes the
LPE audio device and creates a new sound card.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reports live state of PSR2 form PSR2_STATUS register.
bit field 31:28 gives the live state of PSR2.
It can be used to check if system is in deep sleep,
selective update or selective update standby.
During video play back, we can use this to check
if system is entering SU mode or not.
when system is in idle state, DEEP_SLEEP(8) must be entered.
When video playback is happening, system must be in
SLEEP(3 / selective update) or SU_STANDBY( 6 / selective update standby)
v2: (Rodrigo)
- Remove EDP_PSR2_STATUS_TG_ON=a ,instead use ARRAY_SIZE
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483720352-24761-1-git-send-email-vathsala.nagaraju@intel.com
Program EDP_PSR_DEBUG_CTL (PSR_MASK) to enable system
to go to deep sleep while in psr2.PSR2_STATUS bit 31:28
should report value 8 , if system enters deep sleep state.
Also, EDP_FRAMES_BEFORE_SU_ENTRY is set 1 , if not set,
flickering is observed on psr2 panel.
v2: (Ilia Mirkin)
- Remove duplicate bit definition 25:27
v3: rebase
v4: rebase
v5: rebase
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484267484-21843-1-git-send-email-vathsala.nagaraju@intel.com
As per bpsec, CHICKEN_TRANS_EDP bit 12 ,15 must be programmed in
psr2 enable sequence.
bit 12 : Program Transcoder EDP VSC DIP header with a valid setting for
PSR2 and Set CHICKEN_TRANS_EDP(0x420cc) bit 12 for programmable
header packet.
bit 15 : Set CHICKEN_TRANS_EDP(0x420cc) bit 15 if Y coordinate is supported
v2: (Rodrigo)
- move CHICKEN_TRANS_EDP bit set logic right after setup_vsc
v3:(Rodrigo)
- initialize chicken_trans to CHICKEN_TRANS_BIT12 instead of 0
v4:(chris wilson)
- use BIT(12), remove CHICKEN_TRANS_BIT12
- remove unnecessary comments
- update commit message
v5:
- rename bit 12 PSR2_VSC_ENABLE_PROG_HEADER
- rename bit 15 PSR2_ADD_VERTICAL_LINE_COUNT
v6:(Rodrigo)
- remove TRANS_EDP=3, use cpu_transcoder
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: vathsala nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484247691-20930-1-git-send-email-vathsala.nagaraju@intel.com
Psr1 and psr2 are mutually exclusive,ie when psr2 is enabled,
psr1 should be disabled.When psr2 is exited , bit 31 of reg
PSR2_CTL must be set to 0 but currently bit 31 of SRD_CTL
(psr1 control register)is set to 0.
Also ,PSR2_IDLE state is looked up from SRD_STATUS(psr1 register)
instead of PSR2_STATUS register, which has wrong data, resulting
in blankscreen.
hsw_enable_source is split into hsw_enable_source_psr1 and
hsw_enable_source_psr2 for easier code review and maintenance,
as suggested by rodrigo and jim.
v2: (Rodrigo)
- Rename hsw_enable_source_psr* to intel_enable_source_psr*
v3: (Rodrigo)
- In hsw_psr_disable ,
1) for psr active case, handle psr2 followed by psr1.
2) psr inactive case, handle psr2 followed by psr1
v4:(Rodrigo)
- move psr2 restriction(32X20) to match_conditions function
returning false and fully blocking PSR to a new patch before
this one.
v5: in source_psr2, removed val = EDP_PSR_ENABLE
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484244059-9201-1-git-send-email-vathsala.nagaraju@intel.com
BSpec says:
"Overlay Clock Gating Must be Disabled: Overlay & L2 Cache clock gating
must be disabled in order to prevent device hangs when turning off overlay.SW
must turn off Ovrunit clock gating (6200h) and L2 Cache clock gating (C8h)."
We only turned off the overlay clock gating (due to lack of docs I
presume). After a bit of experimentation it looks like the the magic
C8h register lives in the PCI config space of device 0, and the magic
bit appears to be bit 2. Or at the very least this eliminates the GPU
death after MI_OVERLAY_OFF.
L2 clock gating seems to save ~80mW, so let's keep it on unless we need
to actually use the overlay.
Also let's move the OVRUNIT clock gating to the same place since we can,
and 845 supposedly doesn't need it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481131693-27993-11-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Follow the PLL enable sequence updated in bspec, which requires the DCC
delay range 2 bit to be set.
v2: Moved from DDI init sequence to PLL enable.
v3: Don't read value from GRP register. (Rodrido)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-5-git-send-email-ander.conselvan.de.oliveira@intel.com
Geminilake is mostly backwards compatible with broxton, so change most
of the IS_BROXTON() checks to IS_GEN9_LP(). Differences between the
platforms will be implemented in follow-up patches.
v2: Don't reuse broxton's path in intel_update_max_cdclk().
Don't set plane count as in broxton.
v3: Rebase
v4: Include the check intel_bios_is_port_hpd_inverted().
Commit message.
v5: Leave i915_dmc_info() out; glk's csr version != bxt's. (Rodrigo)
v6: Rebase.
v7: Convert a few mode IS_BROXTON() occurances in pps, ddi, dsi and pll
code. (Rodrigo)
v8: Squash a couple of DDI patches with more conversions. (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-2-git-send-email-ander.conselvan.de.oliveira@intel.com
Doing cmd_header >> 29 to extract our 3-bit client value where we know
cmd_header is a u32 shouldn't then also require the use of a mask. So
remove the redundant operation and get rid of INSTR_CLIENT_MASK now that
there are no longer any users.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479163174-29686-1-git-send-email-matthew.auld@intel.com
Use intel_plane->id to derive the VLV/CHV sprite register offsets
instead of abusing plane->plane which is really meant to for
primary planes only.
v2: Convert assert_sprites_disabled() over as well
v3: Rename the reg macro parameter to 'plane_id' as well (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479830524-7882-6-git-send-email-ville.syrjala@linux.intel.com
Gen graphics hardware can be set up to periodically write snapshots of
performance counters into a circular buffer via its Observation
Architecture and this patch exposes that capability to userspace via the
i915 perf interface.
v2:
Make sure to initialize ->specific_ctx_id when opening, without
relying on _pin_notify hook, in case ctx already pinned.
v3:
Revert back to pinning ctx upfront when opening stream, removing
need to hook in to pinning and to update OACONTROL on the fly.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Sourab Gupta <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161107194957.3385-7-robert@sixbynine.org
OACONTROL changes quite a bit for gen8, with some bits split out into a
per-context OACTXCONTROL register. Rename now before adding more gen7 OA
registers
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Sourab Gupta <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161107194957.3385-3-robert@sixbynine.org
Decoupled MMIO is an alternative way to access forcewake domain
registers, which requires less cycles for a single read/write and
avoids frequent software forcewake.
This certainly gives advantage over the forcewake as this new
mechanism “decouples” CPU cycles and allow them to complete even
when GT is in a CPD (frequency change) or C6 state.
This can co-exist with forcewake and we will continue to use forcewake
as appropriate. E.g. 64-bit register writes to avoid writing 2 dwords
separately and land into funny situations.
v2:
- Moved platform check out of the function and got rid of duplicate
functions to find out decoupled power domain (Chris)
- Added a check for forcewake already held and skipped decoupled
access (Chris)
- Skipped writing 64 bit registers through decoupled MMIO (Chris)
v3:
- Improved commit message with more info on decoupled mmio (Tvrtko)
- Changed decoupled operation to enum and used u32 instead of
uint_32 data type for register offset (Tvrtko)
- Moved HAS_DECOUPLED_MMIO to device info (Tvrtko)
- Added lookup table for converting fw_engine to pd_engine (Tvrtko)
- Improved __gen9_decoupled_read and __gen9_decoupled_write
routines (Tvrtko)
v4:
- Fixed alignment and variable names (Chris)
- Write GEN9_DECOUPLED_REG0_DW1 register in just one go (Zhe Wang)
v5:
- Changed HAS_DECOUPLED_MMIO() argument name to dev_priv (Tvrtko)
- Sanitize info->had_decoupled_mmio at init (Chris)
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Praveen Paneri <praveen.paneri@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479230360-22395-1-git-send-email-praveen.paneri@intel.com
The port registers related to the phys in broxton map to different
channels and specific phys. Make that mapping explicit.
v2: Pass enum dpio_phy to macros instead of mmio base. (Imre)
v3: Fix typo in macros. (Imre)
v4: Also change variables from u32 to enum dpio_phy. (Imre)
Remove leftovers from previous version. (Imre)
v5: Actually git add the changes.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476863940-6019-1-git-send-email-ander.conselvan.de.oliveira@intel.com
When modeset occurs and the LS_CLK is set to some special values in DP
mode, the N/M need to be set manually if audio is playing. Otherwise the
first several seconds may be silent in audio playback.
The relationship of Maud and Naud is expressed in the following
equation:
Maud/Naud = 512 * fs / f_LS_Clk
Please refer VESA DisplayPort Standard spec for details.
v2 by Jani:
- organize Maud/Naud table according to DP 1.4 spec
- add 64k and 128k audio rates
- update HSW_AUD_M_CTS_ENABLE register when Maud not found
- remove extra checks for port clock
- simplify Maud/Naud lookup
- reset patch author back to Libin
Cc: "Zhang, Keqiao" <keqiao.zhang@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: "Lin, Mengdong" <mengdong.lin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477407258-30599-3-git-send-email-jani.nikula@intel.com
There are certain types of interrupts which Host can receive from GuC.
GuC ukernel sends an interrupt to Host for certain events, like for
example retrieve/consume the logs generated by ukernel.
This patch adds support to receive interrupts from GuC but currently
enables & partially handles only the interrupt sent by GuC ukernel.
Future patches will add support for handling other interrupt types.
v2:
- Use common low level routines for PM IER/IIR programming (Chris)
- Rename interrupt functions to gen9_xxx from gen8_xxx (Chris)
- Replace disabling of wake ref asserts with rpm get/put (Chris)
v3:
- Update comments for more clarity. (Tvrtko)
- Remove the masking of GuC interrupt, which was kept masked till the
start of bottom half, its not really needed as there is only a
single instance of work item & wq is ordered. (Tvrtko)
v4:
- Rebase.
- Rename guc_events to pm_guc_events so as to be indicative of the
register/control block it is associated with. (Chris)
- Add handling for back to back log buffer flush interrupts.
v5:
- Move the read & clearing of register, containing Guc2Host message
bits, outside the irq spinlock. (Tvrtko)
v6:
- Move the log buffer flush interrupt related stuff to the following
patch so as to do only generic bits in this patch. (Tvrtko)
- Rebase.
v7:
- Remove the interrupts_enabled check from gen9_guc_irq_handler, want to
process that last interrupt also before disabling the interrupt, sync
against the work queued by irq handler will be done by caller disabling
the interrupt.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Remove never used BSM{,_MASK}. BSM_MASK #define also causes a warning.
include/drm/i915_drm.h:96:34: warning: result of ‘65535 << 20’
requires 37 bits to represent, but ‘int’ only has 32 bits
[-Wshiftoverflow=]
#define INTEL_BSM_MASK (0xFFFF << 20)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1476256734-6457-1-git-send-email-joonas.lahtinen@linux.intel.com
Since both legacy and execlists want to populate the RING_CTL register,
share the computation of the right bits for the ring->size. We can then
stop masking errors and explicitly forbid them during creation!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161004201132.21801-1-chris@chris-wilson.co.uk
v2: (Imre)
- Access only subslices that are known to exist.
- Reset explicitly the MCR selector to slice/sub-slice ID 0 after the
readout.
- Use the subslice INSTDONE bits for the hangcheck/subunits-stuck
detection too.
- Take the uncore lock for the MCR-select/subslice-readout sequence.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474379673-28326-2-git-send-email-imre.deak@intel.com
Consolidate the instdone logic so we can get a bit fancier. This patch also
removes the duplicated print of INSTDONE[0].
v2: (Imre)
- Rebased on top of hangcheck INSTDONE changes.
- Move all INSTDONE registers into a single struct, store it within the
engine error struct during error capturing.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474379673-28326-1-git-send-email-imre.deak@intel.com
No functional changes; just renaming a bit, tweaking a datatype,
prettifying layout, and adding comments, in particular in the
GuC setup code that touches this data.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473711577-11454-2-git-send-email-david.s.gordon@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since the watermark calculations for Skylake are still broken, we're apt
to hitting underruns very easily under multi-monitor configurations.
While it would be lovely if this was fixed, it's not. Another problem
that's been coming from this however, is the mysterious issue of
underruns causing full system hangs. An easy way to reproduce this with
a skylake system:
- Get a laptop with a skylake GPU, and hook up two external monitors to
it
- Move the cursor from the built-in LCD to one of the external displays
as quickly as you can
- You'll get a few pipe underruns, and eventually the entire system will
just freeze.
After doing a lot of investigation and reading through the bspec, I
found the existence of the SAGV, which is responsible for adjusting the
system agent voltage and clock frequencies depending on how much power
we need. According to the bspec:
"The display engine access to system memory is blocked during the
adjustment time. SAGV defaults to enabled. Software must use the
GT-driver pcode mailbox to disable SAGV when the display engine is not
able to tolerate the blocking time."
The rest of the bspec goes on to explain that software can simply leave
the SAGV enabled, and disable it when we use interlaced pipes/have more
then one pipe active.
Sure enough, with this patchset the system hangs resulting from pipe
underruns on Skylake have completely vanished on my T460s. Additionally,
the bspec mentions turning off the SAGV with more then one pipe enabled
as a workaround for display underruns. While this patch doesn't entirely
fix that, it looks like it does improve the situation a little bit so
it's likely this is going to be required to make watermarks on Skylake
fully functional.
This will still need additional work in the future: we shouldn't be
enabling the SAGV if any of the currently enabled planes can't enable WM
levels that introduce latencies >= 30 µs.
Changes since v11:
- Add skl_can_enable_sagv()
- Make sure we don't enable SAGV when not all planes can enable
watermarks >= the SAGV engine block time. I was originally going to
save this for later, but I recently managed to run into a machine
that was having problems with a single pipe configuration + SAGV.
- Make comparisons to I915_SKL_SAGV_NOT_CONTROLLED explicit
- Change I915_SAGV_DYNAMIC_FREQ to I915_SAGV_ENABLE
- Move printks outside of mutexes
- Don't print error messages twice
Changes since v10:
- Apparently sandybridge_pcode_read actually writes values and reads
them back, despite it's misleading function name. This means we've
been doing this mostly wrong and have been writing garbage to the
SAGV control. Because of this, we no longer attempt to read the SAGV
status during initialization (since there are no helpers for this).
- mlankhorst noticed that this patch was breaking on some very early
pre-release Skylake machines, which apparently don't allow you to
disable the SAGV. To prevent machines from failing tests due to SAGV
errors, if the first time we try to control the SAGV results in the
mailbox indicating an invalid command, we just disable future attempts
to control the SAGV state by setting dev_priv->skl_sagv_status to
I915_SKL_SAGV_NOT_CONTROLLED and make a note of it in dmesg.
- Move mutex_unlock() a little higher in skl_enable_sagv(). This
doesn't actually fix anything, but lets us release the lock a little
sooner since we're finished with it.
Changes since v9:
- Only enable/disable sagv on Skylake
Changes since v8:
- Add intel_state->modeset guard to the conditional for
skl_enable_sagv()
Changes since v7:
- Remove GEN9_SAGV_LOW_FREQ, replace with GEN9_SAGV_IS_ENABLED (that's
all we use it for anyway)
- Use GEN9_SAGV_IS_ENABLED instead of 0x1 for clarification
- Fix a styling error that snuck past me
Changes since v6:
- Protect skl_enable_sagv() with intel_state->modeset conditional in
intel_atomic_commit_tail()
Changes since v5:
- Don't use is_power_of_2. Makes things confusing
- Don't use the old state to figure out whether or not to
enable/disable the sagv, use the new one
- Split the loop in skl_disable_sagv into it's own function
- Move skl_sagv_enable/disable() calls into intel_atomic_commit_tail()
Changes since v4:
- Use is_power_of_2 against active_crtcs to check whether we have > 1
pipe enabled
- Fix skl_sagv_get_hw_state(): (temp & 0x1) indicates disabled, 0x0
enabled
- Call skl_sagv_enable/disable() from pre/post-plane updates
Changes since v3:
- Use time_before() to compare timeout to jiffies
Changes since v2:
- Really apply minor style nitpicks to patch this time
Changes since v1:
- Added comments about this probably being one of the requirements to
fixing Skylake's watermark issues
- Minor style nitpicks from Matt Roper
- Disable these functions on Broxton, since it doesn't have an SAGV
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-3-git-send-email-cpaul@redhat.com
[mlankhorst: ENOSYS -> ENXIO, whitespace fixes]
In order to add proper support for the SAGV, we need to be able to know
what the cause of a failure to change the SAGV through the pcode mailbox
was. The reasoning for this is that some very early pre-release Skylake
machines don't actually allow you to control the SAGV on them, and
indicate an invalid mailbox command was sent.
This also might come in handy in the future for debugging.
Changes since v1:
- Add functions for interpreting gen6 mailbox error codes along with
gen7+ error codes, and actually interpret those codes properly
- Renamed patch to reflect new behavior
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-2-git-send-email-cpaul@redhat.com
[mlankhorst: -ENOSYS -> -ENXIO for checkpatch]
Atm the LVDS encoder depends on the PPS HW context being saved/restored
from generic suspend/resume code. Since the PPS is specific to the LVDS
and eDP encoders a cleaner way is to reinitialize it during encoder
enabling, so do this here for LVDS. Follow-up patches will init the PPS
for the eDP encoder similarly and remove the suspend/resume time save /
restore.
v2:
- Apply BSpec +1 offset and use DIV_ROUND_UP() when programming the
power cycle delay. (Ville)
v3: (Ville)
- Fix +1 vs. round-up order.
- s/reset_on_powerdown/powerdown_on_reset/
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-3-git-send-email-imre.deak@intel.com
The PPS registers are pretty much the same everywhere, the differences
being:
- Register fields appearing, disappearing from one platform to the
next: panel-reset-on-powerdown, backlight-on, panel-port,
register-unlock
- Different register base addresses
- Different number of PPS instances: 2 on VLV/CHV/BXT, 1 everywhere
else.
We can merge the separate set of PPS definitions by extending the PPS
instance argument to all platforms and using instance 0 on platforms
with a single instance. This means we'll need to calculate the register
addresses dynamically based on the given platform and PPS instance.
v2:
- Simplify if ladder in intel_pps_get_registers(). (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-1-git-send-email-imre.deak@intel.com
Since commit de1add3605 ("drm/i915: Decouple execbuf uAPI from internal
implementation") the index of the engine (its engine->id) in the
internal list no longer matches the hardware id. However, in a couple of
locations we missed fixing up the difference. In this case,
RING_FAULT_REG() refers to engine->id which is now not what the register
offset actually should be. Fortunately, in both case we should be more
or less looping over 0..I915_NUM_ENGINES.
Fixes: de1add3605 ("drm/i915: Decouple execbuf uAPI from internal...")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469643077-2523-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Updated the i915_drpc_info debugfs with coarse power gating & forcewake
info for Gen9.
v2: Change all IS_GEN9() by gen >= 9 (Damien)
v3: Rebase
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1467038401-8283-1-git-send-email-akash.goel@intel.com
Bspec says:
"For DDIA with x4 capability (DDI_BUF_CTL DDIA Lane Capability Control =
DDIA x4), the I_boost value has to be programmed in both
tx_blnclegsctl_0 and tx_blnclegsctl_4."
Currently we only program tx_blnclegsctl_0. Let's do the other one as
well.
Cc: stable@vger.kernel.org
Fixes: f8896f5d58 ("drm/i915/skl: Buffer translation improvements")
Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468328376-6380-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
'ring' is an old deprecated term for a GPU engine. Here we make the
terminology more consistent by renaming the 'ring' parameter of lots of
macros that calculate addresses within the MMIO space of an engine.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469034967-15840-2-git-send-email-david.s.gordon@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add WaDisableGatherAtSetShaderCommonSlice for all gen9 as stated
by bspec. The bspec told to put this workaround to the per ctx bb.
Initial implementation and subsequent review were done based on
bspec. Arun raised a suspicion that this would belong to indirect bb
instead and he conducted more throughout investigation on the matter
and indeed the documentation was wrong.
v2: Move to indirect_ctx wa bb, as it is correct place (Arun)
References: HSD#2135817
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com> (v1)
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469013973-24104-1-git-send-email-mika.kuoppala@intel.com
Add this workaround to prevent hang when in place compression
is used.
References: HSD#2135774
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
BXT BIOS has two options related to GPU power management: "RC6(Render
Standby)" and "GT PM Support". The assumption so far was that disabling
either of these options would leave RC6 uninitialized. According to my
tests this isn't so: for a proper RC6 setup we only need the "GT PM
Support" option to be enabled while the "RC6" option only controls
whether RC6 is left enabled or not by BIOS. OTOH we were missing a few
checks to ensure a proper RC6 setup. Add these now and don't fail the
sanity check if RC6 is disabled. This fixes a problem where RC6 remains
disabled after reloading the driver, since we explicitly disable RC6
during unloading.
v2:
- Print a debug message about the BIOS enabled RC state. (Sagar)
CC: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467216835-1086-2-git-send-email-imre.deak@intel.com
Currently the addressing mode bit in context descriptor is statically
generated from the configuration of system-wide PPGTT usage model.
GVT-g will load the PPGTT shadow page table by itself and probably one
guest is using a different addressing mode with i915 host. The addressing
mode bits of a LRC context should be configurable under this case.
v10:
- Fix the identation. (Joonas)
v9:
- Rename the data member in struct i915_gem_context. (Chris)
v8:
- Rename the data member in struct i915_gem_context. (Chris)
v7:
- Move context addressing mode bit into i915_reg.h. (Joonas/Chris)
- Add prefix "INTEL_" for related definitions. (Joonas)
v6:
- Directly save the addressing mode bits inside i915_gem_context. (Chris)
- Move the LRC context addressing mode bits into intel_lrc.h. (Chris)
v5:
- Change USES_FULL_48BIT(dev) to USES_FULL_48BIT(dev_priv) (Tvrtko)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v9)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-7-git-send-email-zhi.a.wang@intel.com
Backmerge drm-next to get at the nonblocking atomic helpers, needed to
merge the i915 conversion.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This is a WA affecting pooled eu which is a bxt specific feature.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Winiarski, Michal <michal.winiarski@intel.com>
Cc: Zou, Nanhai <nanhai.zou@intel.com>
Cc: Yang, Rong R <rong.r.yang@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
This mode allows to assign EUs to pools which can process work collectively.
The command to enable this mode should be issued as part of context initialization.
The pooled mode is global, once enabled it has to stay the same across all
contexts until HW reset hence this is sent in auxiliary golden context batch.
Thanks to Mika for the preliminary review and comments.
v2: explain why this is enabled in golden context, use feature flag while
enabling the support (Chris)
v3: Include only kernel support as userspace support is not available yet.
User space clients need to know when the pooled EU feature is present
and enabled on the hardware so that they can adapt work submissions.
Create a new device info flag for this purpose.
Set has_pooled_eu to true in the Broxton static device info - Broxton
supports the feature in hardware and the driver will enable it by
default.
We need to add getparam ioctls to enable userspace to query availability of
this feature and to retrieve min. no of eus in a pool but we will expose
them once userspace support is available. Opensource users for this feature
are mesa, libva and beignet.
Beignet team is currently working on adding userspace support.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Winiarski, Michal <michal.winiarski@intel.com>
Cc: Zou, Nanhai <nanhai.zou@intel.com>
Cc: Yang, Rong R <rong.r.yang@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Tim Gore <tim.gore@intel.com>
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We can check the power state of the PHY data and common lanes as
reported by the PHY. Do this in case we need to debug problems where the
PHY gets stuck in an unexpected state.
Note that I only check these when the lanes are expected to be powered
on purpose, since it's not clear at what point the PHY power/clock gates
things.
v2:
- Don't report the encoder as disabled when the sanity check fails.
(Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465825477-32671-1-git-send-email-imre.deak@intel.com
So far we depended on the HW to dynamically power down unused PHYs and
so we enabled them manually once during driver loading/resuming. There
are indications however that we can achieve better power savings by
manual powering toggling. So make the PHY enabling/disabling to happen
on-demand whenever we need either the corresponding AUX or port
functionality. CHV does this already by enabling the PHY along the
corresponding PHY common lane power wells there, do the same on BXT by
adding virtual power wells for the same purpose.
Also sanity check the common lane power down ack signal from the PHY. Do
this only when the PHY is enabled, since it's not clear at what point
the HW power/clock gates things.
While at it rename broxton_ prefix to bxt_ in related function names to
better align with the SKL code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
This patch enables a workaround for a mid thread preemption
issue where a hardware timing problem can prevent the
context restore from happening, leading to a hang.
v2: move to gen9_init_workarounds (Arun)
v3: move to start of gen9_init_workarounds (Arun)
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465816501-25557-1-git-send-email-tim.gore@intel.com
- some polish for the guc code (Dave Gordon)
- big refactoring of gen9 display clock handling code (Ville)
- refactoring work in the context code (Chris Wilson)
- give encoder/crtc/planes useful names for debug output (Ville)
- improvements to skl/kbl wm computation code (Mahesh Kumar)
- bunch of smaller improvements all over as usual
* tag 'drm-intel-next-2016-06-06' of git://anongit.freedesktop.org/drm-intel: (64 commits)
drm/i915: Update DRIVER_DATE to 20160606
drm/i915: Extract physical display dimensions from VBT
drm/i915: Silence "unexpected child device config size" for VBT on 845g
drm/i915/skl+: Use scaling amount for plane data rate calculation (v4)
drm/i915/skl+: calculate plane pixel rate (v4)
drm/i915/skl+: calculate ddb minimum allocation (v6)
drm/i915: Don't try to calculate relative data rates during hw readout
drm/i915: Only ignore eDP ports that are connected
drm/i915: Update GEN6_PMINTRMSK setup with GuC enabled
drm/i915: kill STANDARD/CURSOR plane screams
drm/i915: Give encoders useful names
drm/i915: Give meaningful names to all the planes
drm/i915: Don't leak primary/cursor planes on crtc init failure
drm/i915: Set crtc->name to "pipe A", "pipe B", etc.
drm/i915: Use plane->name in debug prints
drm/i915: Use crtc->name in debug messages
drm/i915: Reject modeset if the dotclock is too high
drm/i915: Fix NULL pointer deference when out of PLLs in IVB
drm/i915/ilk: Don't disable SSC source if it's in use
drm/i915/bxt: Sanitize CDCLK to fix breakage during S4 resume
...
Bspec states that we need to set nuke on modify all to prevent
screen corruption with fbc on skl and kbl.
v2: proper workaround name
References: HSD#2227109, HSDES#1404569388
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-27-git-send-email-mika.kuoppala@intel.com
Set bit 8 in 0x43224 to prevent screen corruption and system
hangs on high memory bandwidth conditions. The same wa also suggest
setting bit 31 on ARB_CTL. According to another workaround we gain
better idle power savings when FBC is enabled.
v2: use correct workaround name
v3: split out overlapping wa for corruption avoidance (Ville)
References: HSD#2137218, HSD#2227171, HSD#2136579, BSID#883
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-26-git-send-email-mika.kuoppala@intel.com
According to bspec this workaround helps to reduce lag and improve
performance on edp.
Documentation suggests this for bdw and all gen9. However evidence
shows that this register is missing on gen9 and causing unclaimed mmio
access if we access it. So apply to bdw only where the reg
exists and can hold its value.
v2: drop skl
References: HSD#2134579
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-11-git-send-email-mika.kuoppala@intel.com
We need to disable clock gating in this unit to work around
hardware issue causing possible corruption/hang.
v2: name the bit (Ville)
v3: leave the fix enabled for 2227050 and set correct bit (Matthew)
References: HSD#2227156, HSD#2227050
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465309159-30531-2-git-send-email-mika.kuoppala@intel.com
Fix the failure mode where the display appears split, or shifted about
2/3 of the screen, and the color components are cycled. Turns out we
were missing the crucial BXT_DEFEATURE_DPI_FIFO_CTR bit in the
EOT_DISABLE register.
Per bspec, with the bit set, the "mipi_dpf_vblank_start" signal is
asserted only when the complete frame is transferred in the DPHY line
and also the DPI FIFO is flushed out at the end of each frame.
The problem was mitigated by keeping the panel fitter enabled, but that
only limited the issue to a shift of about 0..10 pixels. With the fix
here, the panel fitter workaround does not seem to be needed at all.
While at it, set BXT_DPHY_DEFEATURE_EN in EOT_DISABLE register which is
also needed per the BXT DSI mode set sequence.
Issue: VIZ-7610
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464965825-31035-1-git-send-email-jani.nikula@intel.com
Just fallout from switching from asciidoc to sphinx/rst.
v2: Found more. Also s/\//#/ in the vgpu ascii-art - sphinx treats
those as comments and switch to variable-width, which wreaks the
layout.
v3: Undo some of the hacks, rebasing onto latest version of Jani's
series fixed it.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
On Loading, GuC sets PM interrupts routing (bit 31) and clears ARAT
expired interrupt (bit 9). Host turbo also updates this register
in RPS flows. This patch ensures bit 31 and bit 9 setup by GuC persists.
ARAT timer interrupt is needed in GuC for various features. It also
facilitates halting GuC and hence achieving RC6. PM interrupt routing
will not impact RPS interrupt reception by host as GuC will redirect
them.
This patch fixes igt test pm_rc6_residency that was failing with guc
load/submission enabled. Tested with SKL GuC v6.1 and BXT GuC v5.1 and v8.7.
v2: i915_irq/i915_pm decoupling from intel_guc. (ChrisW)
v3: restructuring the mask update and rebase w.r.t Ville's patch. (ChrisW)
v4: Updating the pm_intr_keep during direct_interrupts_to_guc. (Sagar)
Cc: Chris Harris <chris.harris@intel.com>
Cc: Zhe Wang <zhe1.wang@intel.com>
Cc: Deepak S <deepak.s@intel.com>
Cc: Satyanantha, Rama Gopal M <rama.gopal.m.satyanantha@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Testcase: igt/pm_rc6_residency
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464683307-19475-1-git-send-email-sagar.a.kamble@intel.com
Found this while browsing Bspec. Looks like it applies to both skl and
kbl.
v2: Also for bxt (Art).
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Cc: "Runyan, Arthur J" <arthur.j.runyan@intel.com>
Reviewed-by: Sonika Jindal<sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463642060-30728-1-git-send-email-daniel.vetter@ffwll.ch
BXT could change the CD2X divider synchronized with a single pipe.
So assuming the DE PLL frequency doesn't need to be changed, we could
change cdclk without shutting off the pipe (when only a single pipe is
enabled). In the meantime let's configure CDCLK_CTL for non-double
buffered CD2X update, although it shouldn't really matter as long as
the selected pipe is disabled when reprogramming the divider.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462995892-32416-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
While browsing BSpec I bumped into a note saying we need to tune these
values based on actual measurements done after initial enabling. I've
checked that it indeed improves things on BXT. I haven't checked this on
CHV, but here it is if someone wants to give it a go.
v2:
- Add note about the discrepancy wrt. to the spec in the formula
calculating the credit encodings. (Mika, Ville)
- Move the WA comment to the new function. (Ville)
v3:
- Keep the comment about the SQC WA in the caller. (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462280061-1457-4-git-send-email-imre.deak@intel.com
No need for hard-coding the register value, the corresponding fields are
defined properly in BSpec.
No functional change.
v2:
- Rebased on BXT L3 SQC tuning patch merged meanwhile.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1462280061-1457-3-git-send-email-imre.deak@intel.com
Update CDCLK_FREQ on BDW after changing the cdclk frequency. Not sure
if this is a late addition to the spec, or if I simply overlooked this
step when writing the original code.
This is what Bspec has to say about CDCLK_FREQ:
"Program this field to the CD clock frequency minus one. This is used to
generate a divided down clock for miscellaneous timers in display."
And the "Broadwell Sequences for Changing CD Clock Frequency" section
clarifies this further:
"For CD clock 337.5 MHz, program 337 decimal.
For CD clock 450 MHz, program 449 decimal.
For CD clock 540 MHz, program 539 decimal.
For CD clock 675 MHz, program 674 decimal."
Cc: stable@vger.kernel.org
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: b432e5cfd5 ("drm/i915: BDW clock change support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461689194-6079-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
I just noticed that VLV/CHV have a RAWCLK_FREQ register just like PCH
platforms. It lives in the display power well, so we should update it
when enabling the power well.
Interestingly the BIOS seems to leave it at the reset value (125) which
doesn't match the rawclk frequency on VLV/CHV (200 MHz). As always with
these register, the spec is extremely vague what the register does. All
it says is: "This is used to generate a divided down clock for
miscellaneous timers in display." Based on a quick test, at least AUX
and PWM appear to be unaffected by this.
But since the register is there, let's configure it in accordance with
the spec.
Note that we have to move intel_update_rawclk() to occur before we
touch the power wells, so that the dev_priv->rawclk_freq is already
populated when the disp2 enable hook gets called for the first time.
I think this should be safe to do on other platforms as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461768202-17544-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch applies a performance enhancement workaround
based on analysis of DX and OCL S-Curve workloads. We
increase the General Priority Credits for L3SQ from the
hardware default of 56 to the max value 62, and decrease
the High Priority credits from 8 to 2.
v2: Only apply to B0 onwards
v3: Move w/a to per engine init, ie bxt_init_workarounds
Signed-off-by: Tim Gore <tim.gore@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461314761-36854-1-git-send-email-tim.gore@intel.com
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Added a new GT_PM_INTERVAL_TO_US macro to perform the platform
specific conversion of PM time interval values to microseconds unit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-1-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b12:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.
v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This has been corrected in BSpec quite some time ago, but we missed it
somehow. The wrong field definitions resulted in configuring PHY0 with
an incorrect GRC value.
v2:
- Remove the FIXME comment, we left in the code exactly about this
issue. (Ville)
CC: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459515767-29228-3-git-send-email-imre.deak@intel.com
On CHV GTFIFODBG has some read-only bits to indicate the number
of free FIFO entries. Ignore these when checking to see if any
of the sticky error bits are set.
This gets rid of these during device resume:
[drm:cherryview_enable_rps] GT fifo had a previous error 1080000
While at it, move the assignments out of the if().
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460570970-14073-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With gen9+ the edram capabilities are defined so
that we can calculate the edram (ellc) size accordingly.
Note that there are undefined combinations for some subset of
edram capability bits. Return the closest size for undefined indexes.
Even if we get it wrong with beginning of future gen enabling, the size
information is currently only used for boot message and in debugfs entry.
v2: Use function instead of hard to read macro (Daniel)
v3: s/INTEL_INFO/INTEL_GEN (Matthew)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460557604-7126-2-git-send-email-mika.kuoppala@intel.com
Store the edram capabilities instead of only the size of
edram. This is preparatory patch to allow edram size calculation
based on edram capability bits for gen9+. With gen9 the
edram is behind llc and is a separate entity. With hsw/bdw
it was more of a victim cache for LLC so the name 'eLLC' might
be warranted. Regardless, rename all mentions of eLLC to EDRAM to
clear the confusion.
v2: return bytes for edram size (Chris)
s/eLLC/eDRAM in output if we are gen > 8
v3: rebase, INTEL_GEN (Chris)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
This is to fix a GPU hang seen with mid thread pre-emption
and pooled EUs.
v2. Use IS_BXT_REVID instead of IS_BROXTON and INTEL_REVID
v3. And use correct type for register addresses
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458571049-854-1-git-send-email-tim.gore@intel.com
This patch sets the invert bit for hpd detection for each port
based on VBT configuration. Since each AOB can be designed to
depend on invert bit or not, it is expected if an AOB requires
invert bit, the user will set respective bit in VBT.
v2: Separated VBT parsing from the rest of the logic. (Jani)
v3: Moved setting invert bit logic to bxt_hpd_irq_setup()
and changed its logic to avoid looping twice. (Ville)
v4: Changed the logic to mask out the bits first and then
set them to remove need of temporary variable. (Ville)
v5: Moved defines to existing set of defines for the register
and added required breaks. (Ville)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed some checkpatch noise, added kernel-doc.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459420907-11383-2-git-send-email-shubhangi.shrivastava@intel.com
Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.
Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.
While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.
v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.
As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.
This change implements the following WAs,
WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
DPLL_MD(PIPE_C) is AWOL on CHV. Instead of fixing it someone added
chicken bits to propagate the pixel multiplier from DPLL_MD(PIPE_B)
to either pipe B or C. So do that to make pixel repeat work on pipes
B and C. Pipe A is fine without any tricks.
Fortunately the pixel repeat propagation appears to be a oneshot
operation, so once the value has been written we can clear the
chicken bits. So it is still possible to drive pipe B and C with
different pixel multipliers simultaneosly.
Looks like DPLL_VGA_MODE_DIS must also be set in DPLL(PIPE_B)
for this to work. But since we keep that bit always set in all
DPLLs there's no problem.
This of course means we can't reliably read out the pixel multiplier
for pipes B and C. That would make the state checker unhappy, so I
added shadow copies of those registers in to dev_priv. The other
option would have been to skip pixel multiplier, dpll_md an dotclock
checks entirely on CHV, but that feels like a serious loss of cross
checking, so just pretending that we have working DPLL MD registers
seemed better. Obviously with the shadow copies we can't detect if
the pixel multiplier was properly configured, nor can we take over
its state from the BIOS, but hopefully people won't have displays
that would be limitd to such crappy modes.
There is one strange flicker still remaining. It's visible on
pipe C/HDMID when HDMIB is enabled while driven by pipe B.
It doesn't occur if pipe A drives HDMIB, nor is there any glitch
on pipe B/HDMIB when port C/HDMID starts up. I don't have a board
with HDMIC so not sure if it happens there too. So I'm not sure
if it's somehow tied in with this strange linkage between pipe B
and C. Sadly I was unable to find an enable sequence that would
avoid the glitch, but at least it's not fatal ie. the output
recovers afterwards.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
According to the BSpec update, bit 7 of PORT_CL1CM_DW0 register needs to be
checked to ensure that the register is in accessible state.
Also, based on a BSpec update, changing the timeout value to
check iphypwrgood, from 10ms to wait for up to 100us.
v2: [Ville] use wait_for_us instead of the atomic call.
v3: [Jani/Imre] read register only once
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reported-by: Philippe Lecluse <Philippe.Lecluse@intel.com>
Cc: Deak, Imre <imre.deak@intel.com>
Cc: Nikula, Jani <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459446354-19012-1-git-send-email-vandana.kannan@intel.com
Currently the machine hangs during booting while accessing the
BXT_MIPI_PORT_CTRL register during pipe HW state readout. After some
experimentation I found that the hang is caused by the DSI PLL being
disabled, or it being enabled but with an incorrect divider
configuration. Enabling the PLL got rid of the boot problem, so fix
this by checking the PLL enabled state/configuration before attempting
to read out the HW state.
The DSI_PLL_ENABLE register is in the always-on power well, while the
BXT_DSI_PLL_CTL is in power well 0. This isn't exactly matched by the
transcoder power domain, but what we really need is just a runtime PM
reference, which is provided by any power domain.
Ville also found this dependency specified in BSpec, so I added a
reference to that too.
v2:
- Make sure we hold a power reference while accessing the PLL registers.
v3: (Jani)
- Simplify check in bxt_get_dsi_transcoder_state()
- Add comment explaining why we check for valid dividers in
bxt_dsi_pll_is_enabled()
CC: Shashank Sharma <shashank.sharma@intel.com>
CC: Uma Shankar <uma.shankar@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Fixes: c6c794a2fc ("drm/i915/bxt: Initialize MIPI DSI for BXT")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458816100-31269-1-git-send-email-imre.deak@intel.com
Patch based on a previous series by Shashank Sharma.
v2: Update contributors
v3: Refactor degamma/gamma LUTs load into a single function
v4: Remove unused variable
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-5-git-send-email-lionel.g.landwerlin@intel.com
Patch based on a previous series by Shashank Sharma.
v2: Do not read GAMMA_MODE register to figure what mode we're in
v3: Program PREC_PAL_GC_MAX to clamp pixel values > 1.0
Add documentation on how the Broadcast RGB property is affected by CTM
v4: Update contributors
v5: Refactor degamma/gamma LUTs load into a single function
v6: Fix missing intel_crtc variable (bisect issue)
v7: Fix & simplify limited range matrix multiplication (Matt Roper's
comment)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Acknowledged-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-4-git-send-email-lionel.g.landwerlin@intel.com
This allows writes to EU flow control registers. Together
with SIP code from the user-mode driver this resolves a
hang seen in some pre-emption scenarios. Note that this
patch is just the kernel mode part of this workaround.
v2. Oops, add FLOW_CONTROL_ENABLE macro to i915_reg.h.
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458144826-17269-1-git-send-email-tim.gore@intel.com
In full gpu reset we prime all engines and reset domains corresponding to
each engine. Per engine reset is just a special case of this process
wherein only a single engine is reset. This change is aimed to modify
relevant functions to achieve this. There are some other steps we carry out
in case of engine reset which are addressed in later patches.
Reset func now accepts a mask of all engines that need to be reset. Where
per engine resets are supported, error handler populates the mask
accordingly otherwise all engines are specified.
v2: ALL_ENGINES mask fixup, better for_each_ring_masked (Chris)
v3: Whitespace fixes (Chris)
v4: Rebase due to s/ring/engine
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458143640-20563-1-git-send-email-mika.kuoppala@intel.com
The enum mipi_dsi_pixel_format defines MIPI_DSI_FMT_RGB666 for the
"loose" 24 bpp format and MIPI_DSI_FMT_RGB666_PACKED for the 18 bpp
format. We have this the other way round, defining a loose version for
24 bpp.
Follow suit with what's in enum mipi_dsi_pixel_format to avoid future
confusion. Rename
VID_MODE_FORMAT_RGB666 -> VID_MODE_FORMAT_RGB666_PACKED
VID_MODE_FORMAT_RGB666_LOOSE -> VID_MODE_FORMAT_RGB666
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458123700-16003-1-git-send-email-jani.nikula@intel.com
The MIPI clock calculations for the addtional clock
are revised from B0 stepping onwards, the bit definitions
have changed compared to old stepping.
v2: Fixing compilation warning.
v3: Retained the old Macros (Jani)
Signed-off-by: Deepak M <m.deepak@intel.com>
Tested-by: Ramalingam C <ramalingam.c@intel.com> # BXT-T with Tianma panel
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455556437-29267-1-git-send-email-m.deepak@intel.com
Rather than assume the VGA dotclock is really the FDI based thing,
let's read out the real thing via iclkip, and after readout it'll
get to compare it with the FDI based number to make sure they're
in sync.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cores need to be included into the debug mask. We don't exactly
know what it does but the spec says it must be enabled. So obey.
v2: Cores should be only set for BXT (Imre, Art)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455877564-5128-1-git-send-email-mika.kuoppala@intel.com
Looks like g4x hpd live status bits actually agree with the spec. At
least they do on the machine I have, and apparently on Nick Bowler's
g4x as well.
So gm45 may be the only platform where they don't agree. At least
that seems to be the case based on the (somewhat incomplete)
logs/dumps in [1], and Daniel has also tested this on his gm45
sometime in the past.
So let's change the bits to match the spec on g4x. That actually makes
the g4x bits identical to vlv/chv so we can just share the code
between those platforms, leaving gm45 as the special case.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=52361
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Nick Bowler <nbowler@draconx.ca>
References: https://lists.freedesktop.org/archives/dri-devel/2016-February/100382.html
Reported-by: Nick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455127145-20087-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some Gen7/8 production parts may have the Display Pipe C fused off.
In this case, the display hardware will prevent the enable bit in
PIPE_CONF register (for Pipe C) from being set to 1.
Fixed by adjusting pipe_count to reflect this.
v2: Rename HSW_PIPE_C_DISABLE to IVB_PIPE_C_DISABLE as it already exists
on ivybridge (Ville)
v3: Remove unnecessary MMIO read, correct the description (Damien)
v4: Be more specific in description (Patrick)
Signed-off-by: Gabriel Feceoru <gabriel.feceoru@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453462125-21519-1-git-send-email-gabriel.feceoru@intel.com
We accidentally point both cfgcr registers for the second shared DPLL to
the same location in i915_reg.h. This results in a lot of hw pipe state
mismatches whenever we try to do a modeset that requires allocating the
DPLL to a CRTC:
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x80000168, found 0x000004a5)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 108000, found 49500)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 108000, found 49500)
This usually ends up causing blank monitors, since the DPLL never can
get set to the right clock.
Fixes: 086f8e84a0 ("drm/i915: Prefix raw register defines with underscore")
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1454600601-21900-1-git-send-email-cpaul@redhat.com
RC6 setup is shared between BIOS and Driver. BIOS sets up subset of RC6
setup registers. If those are not setup Driver should not enable RC6.
For implementing this, driver can check RC_CTRL0 and RC_CTRL1 values
to know if BIOS has enabled HW/SW RC6.
This will also enable user to control RC6 using BIOS settings alone.
RC6 related instability can be avoided by disabling via BIOS settings
till driver fixes it.
v2: Had placed logic in gen8 function by mistake. Fixed it.
Ensuring RPM is not enabled in case BIOS disabled RC6.
v3: Need to disable RPM if RC6 is disabled due to BIOS settings. (Daniel)
Runtime PM enabling happens before gen9_enable_rc6.
Moved the updation of enable_rc6 parameter in intel_uncore_sanitize.
v4: Added elaborate check for BIOS RC6 setup. Prepared check_pctx for bxt.
(Imre)
v5: Caching reserved stolen base and size in the driver private data.
Reorganized RC6 setup check. Moved from gen9_enable_rc6 to
intel_uncore_sanitize. (Imre)
v6: Rebasing on the patch submitted by Imre that moves gem_init_stolen
earlier in the load.
v7: Removed PWRCTX_MAXCNT_VCSUNIT1 check as it applies to SKL. (Imre)
v8: Fixed formatting and checkpatch issues. Fixed functional issue where
RC6 ctx size check was missing. (Imre)
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454697809-22113-1-git-send-email-sagar.a.kamble@intel.com
Make the gpio read/write functions more generic iosf sideband read/write
functions, taking the iosf port as argument.
v2: rebase
v3: rebase
v4 by Jani: address Ville's review
v5 by Jani: drop the PCI_DEVFN change (Ville)
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454604915-17142-1-git-send-email-jani.nikula@intel.com
WaIncreaseDefaultTLBEntries increases the number of TLB
entries available for GPGPU workloads and gives significant
( > 10% ) performance gain for some OCL benchmarks.
Put this in a new function that can be a place for
workarounds that are GT related but not required per ring.
This function is called on driver load and also after a
reset and on resume, so it is safe for workarounds that get
clobbered in these situations. This function currently has
just this one workaround.
v2: This was originally split into 3 patches but following
review feedback was squashed into 1.
I have not incorporated some style comments from Chris
Wilson as I felt that after defining and intialising a
temporary variable and then adding an additional if block
to only write the register if the temporary variable had
been set, this didn't really give a net gain.
v3: Resending in the hope that BAT will run
v4: Change subject line to trigger BAT (please!)
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454586574-2343-1-git-send-email-tim.gore@intel.com
On SKL and KBL we can have pipe A/B/C disabled by fuse settings. The
pipes must be fused in descending order (e.g. C, B+C, A+B+C). We simply
decrease info->num_pipes if we find a valid fused out config.
v2: Don't store the pipe disabled mask in device info (Damien)
v3: Don't check FUSE_STRAP register for pipe c disabled
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[Jani: fixed some checkpatch indentation complaints]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453300280-10661-1-git-send-email-patrik.jakobsson@linux.intel.com
Per context preemption granularity control is only available from SKL:E0+
Actual WA is to disable percontext preemption granularity control until D0
which is the default case so this is equivalent to the inverse of
WaDisablePerCtxtPreemptionGranularityControl:skl
v2: add some detail to commit msg (Chris)
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-8-git-send-email-arun.siluvery@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required for,
WaDisableObjectLevelPreemptionForTrifanOrPolygon:bxt
WaDisableObjectLevelPreemptionForInstancedDraw:bxt
WaDisableObjectLevelPreemtionForInstanceId:bxt
According to WA database these are only applicable for BXT:A0 but since
A0 and A1 shares the same GT these are extended for A1 as well.
These are also required for SKL until B0 but not adding them because they
are pre-production steppings.
This register is added to HW whitelist to support WA required for future
enabling of pre-emptive command execution, WA implementation will be in
userspace and it cannot program this register if it is not on HW whitelist.
v2: use lower case in register defines (Nick)
v3: explain purpose of changes (Chris)
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-5-git-send-email-arun.siluvery@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required for WaAllowUMDToModifyHDCChicken1:skl,bxt
This register is added to HW whitelist to support WA required for future
enabling of pre-emptive command execution, WA implementation will be in
userspace and it cannot program this register if it is not on HW whitelist.
v2: explain purpose of changes (Chris)
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-4-git-send-email-arun.siluvery@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required for WaEnablePreemptionGranularityControlByUMD:skl,bxt
This register is added to HW whitelist to support WA required for future
enabling of pre-emptive command execution, WA implementation will be in
userspace and it cannot program this register if it is not on HW whitelist.
v2: explain purpose of WA (Chris)
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-3-git-send-email-arun.siluvery@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some of the HW registers are privileged and cannot be written to from
non-privileged batch buffers coming from userspace unless they are added to
the HW whitelist. This whitelist is maintained by HW and it is different from
SW whitelist. Userspace need write access to them to implement preemption
related WA.
The reason for using this approach is, the register bits that control
preemption granularity at the HW level are not context save/restored; so even
if we set these bits always in kernel they are going to change once the
context is switched out. We can consider making them non-privileged by
default but these registers also contain other chicken bits which should not
be allowed to be modified.
In the later revisions controlling bits are save/restored at context level but
in the existing revisions these are exported via other debug registers and
should be on the whitelist. This patch adds changes to provide HW with a list
of registers to be whitelisted. HW checks this list during execution and
provides access accordingly.
HW imposes a limit on the number of registers on whitelist and it is
per-engine. At this point we are only enabling whitelist for RCS and we don't
foresee any requirement for other engines.
The registers to be whitelisted are added using generic workaround list
mechanism, even these are only enablers for userspace workarounds. But by
sharing this mechanism we get some test assets without additional cost (Mika).
v2: rebase
v3: parameterize RING_FORCE_TO_NONPRIV() as _MMIO() should be limited to
i915_reg.h (Ville), drop inline for wa_ring_whitelist_reg (Mika).
v4: improvements suggested by Chris Wilson.
Clarify that this is HW whitelist and different from the one maintained in
driver. This list is engine specific but it gets initialized along with other
WA which is RCS specific thing, so make it clear that we are not doing any
cross engine setup during initialization.
Make HW whitelist count of each engine available in debugfs.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-2-git-send-email-arun.siluvery@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Dave's drm-next pull request to have a clean base for 4.6.
Also, we need the various atomic state extensions Maarten recently
created.
Conflicts are just adjacent changes that all resolve to nothing in git
diff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Imre mentioned that chv might also have capability to
track unclaimed mmio accesses. Ville added that
both chv and vlv has this capability and he had already
made this way back [1]. Mimic what Ville's patch does
but adapt on top of less frequent mmio accesses by
omitting checking always on reg writes.
This patch is untested as of now.
v2: overflow handling and posting omitted (Ville)
References: [1] http://lists.freedesktop.org/archives/intel-gfx/2013-May/027599.html
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450201542-22918-1-git-send-email-mika.kuoppala@intel.com
- fix atomic watermark recomputation logic (Maarten)
- modeset sequence fixes for LPT (Ville)
- more kbl enabling&prep work (Rodrigo, Wayne)
- first bits for mst audio
- page dirty tracking fixes from Dave Gordon
- new get_eld hook from Takashi, also included in the sound tree
- fixup cursor handling when placed at address 0 (Ville)
- refactor VBT parsing code (Jani)
- rpm wakelock debug infrastructure ( Imre)
- fbdev is pinned again (Chris)
- tune the busywait logic to avoid wasting cpu cycles (Chris)
* tag 'drm-intel-next-2015-12-18' of git://anongit.freedesktop.org/drm-intel: (81 commits)
drm/i915: Update DRIVER_DATE to 20151218
drm/i915/skl: Default to noncoherent access up to F0
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: don't enable autosuspend on platforms without RPM support
drm/i915/backlight: prefer dev_priv over dev pointer
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Pin the ifbdev for the info->system_base GGTT mmapping
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: mdelay(10) considered harmful
drm/i915: check that we are in an RPM atomic section in GGTT PTE updaters
drm/i915: add support for checking RPM atomic sections
drm/i915: check that we hold an RPM wakelock ref before we put it
drm/i915: add support for checking if we hold an RPM reference
drm/i915: use assert_rpm_wakelock_held instead of opencoding it
drm/i915: add assert_rpm_wakelock_held helper
drm/i915: remove HAS_RUNTIME_PM check from RPM get/put/assert helpers
drm/i915: get a permanent RPM reference on platforms w/o RPM support
drm/i915: refactor RPM disabling due to RC6 being disabled
...
DRM Docbook is now Markdown ready. This means its doc is able to
use markdown text on it.
* Documentation/DocBook/drm.tmpl: Contains a table duplicated from
drivers/gpu/drm/i915/i915_reg.h. This is not needed anymore
* drivers/gpu/drm/drm_modeset_lock.c: had a code example that used
to look pretty bad on html. Fixed by using proper code markup.
* drivers/gpu/drm/drm_prime.c: Remove spaces between lines to make
a proper markup list.
* drivers/gpu/drm/i915/i915_reg.h: Altought pandoc supports tables,
it doesn't support table cell spanning. But we can use fixed-width
for those special cases.
* include/drm/drm_vma_manager.h: Another code example that should be
proper indented with four spaces.
v2 (Daniel): Adjust name to gpu.xml due to rename.
v3 (Daniel):
Split out the actual enabling in the Makefile - this way we can merge
the conversion, while just keeping the enabling in a drm-private tree.
Signed-off-by: Danilo Cesar Lemes de Paula <danilo.cesar@collabora.co.uk> (v1)
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448471279-19748-2-git-send-email-daniel.vetter@ffwll.ch
Pipe is assigned based on the port, but it should be
based on current crtc. Correcting the same in this patch.
v2: Use macro BXT_PIPE_SELECT(pipe) (Daniel)
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we want to use SPLL for FDI we want SSC, which means we have to
disable clock bending for the PCH SSC reference (bend and spread are
mutually exclusive). So let's turn off bending when we want spread.
In case the BIOS enabled clock bending for some reason we'll just turn
it off and enable the spread mode instead.
Not sure what happens if the BIOS is actually using the bend source for
HDMI at this time, but I suppose it should be no worse than what already
happens when we simply turn on the spread.
We don't currently use the bend source for anything, and only use the
PCH SSC reference for the SPLL to drive FDI (always with spread).
v2: Fix the %5 vs %10 fumble for SSCDITHPHASE (Paulo)
Add 'WARN_ON(steps % 5 != 0)' sanity check (Paulo)
Fix typos in commit message (Paulo)
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449260379-14093-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
LPT-H has a strap bit for fused off CRT block. Check it to see if
we should register the CRT connector or not. Supposedly this also
forces the ADAP enable bit to 0, so the detection we added in
commit 6c03a6bd0d ("drm/i915: Don't register CRT connector when it's fused off")
should already catch it, but checking the fuse bit should at least
do no harm.
v2: Use HAS_PCH_LPT_H() (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449005335-15192-1-git-send-email-ville.syrjala@linux.intel.com
Per bspec, "Backlight PWM may stop in the asserted state, causing
backlight to stay fully on. WA: Before disabling PWM, set CLKGATE_DIS_0
0x46530 bit 13 PWM1 Gating Dis (for PWM1) or bit 14 PWM2 Gating Dis (for
PWM2). The bits can remain set without harm." (There's no workaround
name for this.)
This fixes some Broxton backlight issues.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: cleanup & commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448958232-26520-3-git-send-email-jani.nikula@intel.com
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
Store the upper dword of the register offset in the whitelist as well.
This would allow it to read register where the two halves aren't sitting
right next to each other, and it'll make it easier to make register
access type safe.
While at it change the register offsets to u32 from u64. Our register
space isn't quite that big, yet :)
v2: Use ldw/udw as the suffixes, and add a note about
64bit wide split regs (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446839021-18599-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Most of our register defines follow the convention that if there's a
need for the raw register offset, that one has an underscore sa a
prefix. The define (possibly parametrized) without the underscore is
the one people should normally use, since it will take into account
all the parameters and other potential offsets that are needed.
Fix up the few stragglers that don't follow this convention.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Handle DC off as a power well where enabling the power well will prevent
the DMC to enter selected DC states (required around modesets and Aux
A). Disabling the power well will allow DC states again. For now the
highest DC state is DC6 for Skylake and DC5 for Broxton but will be
configurable for Skylake in a later patch.
v2: Check both DC5 and DC6 bits in power well enabled function (Ville)
v3:
- Remove unneeded DC_OFF case in skl_set_power_well() (Imre)
- Add PW2 dependency to DC_OFF (Imre)
v4: Put DC_OFF before PW2 in BXT power well array
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[fixed line over 80 and parenthesis alignment checkpatch warns (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447687201-24759-1-git-send-email-patrik.jakobsson@linux.intel.com
lookup_power_well() expects uniq power well IDs, but atm we have
uninitialized IDs which would clash with those power wells with a 0
ID. This wasn't a problem so far since nothing looked up such a power
well, but an upcoming patch will (Misc IO for SKL), so fix this up on
platforms where this matters.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-2-git-send-email-imre.deak@intel.com
Drop the EDP_PSR_BASE() thing, and just stick the PSR register offset
under dev_priv, like we for DSI and GPIO for example.
TODO: could probably move a bunch of this kind of stuff into the device
info instead...
v2: Drop the spurious whitespace change (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-7-git-send-email-ville.syrjala@linux.intel.com
Currently we determine the location of the AUX registers in a confusing
way. First we assume the PCH registers are used always, but then we
override it for everything but HSW/BDW to use DP+0x10. Very confusing.
Let's just make it straightforward and simply add a few functions to
pick the right AUX_CTL based on the DP port.
To deal with VLV/CHV we'll include the display_mmio_offset into the
AUX register defines.
v2: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-5-git-send-email-ville.syrjala@linux.intel.com
v2: Keep some MISSING_CASE() stuff (Jani)
s/-1/-PIPE_B/ in the register macro
Fix typo in patch subject
v3: Use PORT_B registers for invalid ports in g4x_aux_ctl_reg() (Jani)
v4: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-4-git-send-email-ville.syrjala@linux.intel.com
We check these to determine firmware loading status. Include
them to help to debug causes of firmware loading fails.
v2: Move all CSR specific registers to i915_reg.h (Ville)
v3: Rebase
v4: Rebase (RPM ref)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220487-32691-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
For bxt CSR firmware exposes a count of dc5 entries. Expose
it through debugs
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The CSR firmware expose two counters, handy to check if we are indeed
entering DC5/DC6.
v2: Rebase
v3: Take RPM ref before reading (Imre)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446220412-32574-1-git-send-email-mika.kuoppala@intel.com
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
SWF18 is set if the display has been initialized by the pre-os. It also
gives what configuration is enabled on which pipe. In skl_sanitize_cdclk,
the DPLL sanity check can pass even if GOP/VBIOS is not loaded as BIOS
enables DPLL for integrated audio codec related programming.
So fisrt check if SWF18 is set and then follow through with other DPLL
and CDCLK verification. If not set then for sure we need to sanitize the
cdclock.
v2: Update the commit message for clarity (Siva)
v3: Correct the mask to check for bits[23:0] instead of only bits[16:0].
Had missed checking for PIPE C altogether. Remaining are reserved (Siva)
v4: Use ILK_SWF macro for SWF register definitions. Taken from Ville's patch
http://lists.freedesktop.org/archives/intel-gfx/2015-November/079480.html
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446726932-14078-1-git-send-email-shobhit.kumar@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Parametrize the SWF registers. This also fixes the register offsets,
which were mostly garbage in the old defines.
Also save/restore only as many SWF registers that each platform has.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PIPE_FRMCOUNT_GM45 and PIPE_FLIPCOUNT_GM45 names have bothered me
for a long time. The work equally well for ELK and onwards, so let's
s/GM45/G4X/.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few register mask defines were missing the '0x' from hex numbers. Or
at least I assume those were meant to be hex numbers. Put the '0x' in
place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always put parens around macro argument evaluations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Keep using the same registers (PCH_*) instead of accidentally
starting to use the other ones (BXT_*)2) (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that in Bspec you have to dig around in a section called
"Timestamp bases" and Bspec update request is filed.
Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Add note about state of Bspec.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to support glDispatchComputeIndirect for gen7.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BXT DSI clocks are different than previous platforms. So adding a
new function to program following clocks and dividers:
1. Program variable divider to generate input to Tx clock divider
(Output value must be < 39.5Mhz)
2. Select divide by 2 option to get < 20Mhz for Tx clock
3. Program 8by3 divider to generate Rx clock
v2: Fixed Jani's review comments. Adjusted the Macro definition as
per convention. Simplified the logic for bit definitions for
MIPI PORT A and PORT C in same registers.
v3: Refactored the macros for TX, RX Escape and DPHY clocks as per
Jani's suggestion.
v4: Addressed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains following changes:
1. MIPI device ready changes to support dsi_pre_enable. Changes
are specific to BXT device ready sequence. Added check for
ULPS mode(No effects on VLV).
2. Changes in dsi_enable to pick BXT port control register.
3. Changes in dsi_pre_enable to restrict DPIO programming for VLV
v2: Fixed Jani's review comments. Removed the changes in VLV/CHV
code. Fixed the macros to get proper port offsets.
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register was added on GEN4, by the name INSTDONE_1 whereas the GEN6
specification calls it INSTDONE_2. Keep the original name with a
platform prefix to make it clearer which INSTDONE register instance this
is. Also add a comment about the SNB alternative name.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a bunch of INSTDONE registers for different platforms and
purposes and it's not immediately clear which instance they are just by
looking at the register name. This one was added on GEN2, where it was
the only INSTDONE register, so mark it as such.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use 3 different names to refer to the same render ring INSTDONE
register. This can be confusing when comparing two parts of the code
accessing the register via different names. Although the GEN4 version's
layout is different, we treat it the same way as the GEN7+ version, in
that we simply read it out during error capture. So remove the
duplicates and leave a comment about the GEN4 difference.
Note that there is also a GEN2 version of this register, but that's on a
different address so not handled in this patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use SKL_DPLLx symbolic names instead of raw numbers
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added checks for available slices, subslices and EUs for Broadwell. This
information is filled in intel_device_info and is available to user with
GET_PARAM.
Added checks for enabled slices, subslices and EU for Broadwell. This
information is based on available counts but takes power gated slices
into account. It can be read in debugfs.
Introduce new register defines that contain information on slices on
Broadwell.
v2:
- Introduce GT_SLICE_INFO register
- Change Broadwell sseu_device_status function to use GT_SLICE_INFO
register instead of RPCS register
- Undo removal of dev_priv variables in Cherryview and Gen9
sseu_device_satus functions
v3:
- Fix style issues
v4:
- Corrected comment
- Reverted reordering of defines
Cc: Jeff Mcgee <jeff.mcgee@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Łukasz Daniluk <lukasz.daniluk@intel.com>
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As with the cdclk, read out czclk from CCK as well. This gives us the
real current value and avoids having to decode fuses and whatnot.
Also store it in kHz under dev_priv like we do for cdlck since it's not
just an rps related clock, and having it in kHz is more
standard/convenient for some things.
Imre also pointed out that we currently fail to read czclk on VLV, which
means the PFI credit programming isn't working as expected.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the DISPLAY_TRUNK_* and DISPLAY_FREQUENCY_* bits to CCK_... instead
of DISPLAY_... to make it clear they apply to all CCK clock control registers.
Suggested by Ville.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Hide the 945 vs. rest of gen2/3 difference in the macro
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec update tells that we have to enable oscaledcompmethod instead of
ouniqetrangenmethod for enabling scale value during swing programming.
v2: Adding back 'don't care' values to bxt_ddi_translations_dp and add
error message if ouniquetrangemethod was set (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>(v1)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: Should there be a WARN(i != 9) or something, or what does the
entry 9 comment mean?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Finally managed to dig up enough hints as to where the stolen
reserved stuff lives on ctg/elk. So add the code to decode it.
This was a combination of old chipset specs, diggin up an old
elk grits release with an ctg/elk AubLoad etc.
This was only tested on an elk as I don't have a ctg here
unfortunately.
This leaves ilk as the only platform that doesn't have a way
to detect this stuff. Looking at the register contents on my
ilk, it might be that the elk way works there too, but I
can't be sure since I can't affect the amount of reserved
memory on that machine, and if I am to trust the register
contents, by default it would reserve 0 bytes.
v2: s/WARN_ON_ONCE/WARN_ON/ since it's in one time init code
anyway (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch modifies dsi_prepare() function to support the same
modeset prepare sequence for BXT also. Main changes are:
1. BXT port control register is different than VLV.
2. BXT modeset sequence needs vdisplay and hdisplay programmed
for transcoder.
3. BXT can select PIPE for MIPI transcoders.
4. BXT needs to program register MIPI_INIT_COUNT for both the ports,
even if only one is being used.
v2: Fixed Jani's review comments. Rectified the DSI Macros to get
proper register offsets using _MIPI_PORT instead of _TRANSCODER
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds new functions for BXT clock and PLL programming.
They are:
1. configure_dsi_pll for BXT.
This function does the basic math and generates the divider ratio
based on requested pixclock, and program clock registers.
2. enable_dsi_pll function.
This function programs the calculated clock values on the PLL.
3. intel_enable_dsi_pll
Wrapper function to use same code for multiple platforms. It checks the
platform and calls appropriate core pll enable function.
v2: Fixed Jani's review comments. Macros are adjusted as per convention.
v3: Removed a redundant change wrt code comment.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite the BXT hpd setup to match the way we do it on other platforms:
- Throw out BXT_HOTPLUG_CTL since it's the same as PCH_PORT_HOTPLUG
- Enable the HPD bits in the DE port IER in gen8_de_irq_postinstall()
- Update DE port IMR using bdw_update_port_irq()
Also throw out port D from bxt_port_hotplug_long_detect() since BXT only
goes up to C.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL the port A HPD has moved to the PCH. Hook it up.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PORTA HPD defines are not BXT specific. They also exist on SPT,
and partially already on LPT:LP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Indent the PORTx_HOTPLUG_... defines appropriately, and fix some space
vs. tab issues.
v2: Document pre-HSW/LPT bits, and order another tab (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
At various points when changing the DPIO lane/phy power states,
construct an expected value of the DISPLAY_PHY_STATUS register
and compare it with the real thing.
To construct the expected value we look at our shadow PHY_CONTROL
register value (which should match what we've just written to the
hardware), and we also need to look at the actual state of the cmn
power wells as a disabled power well causes the relevant LDO status
to be reported as 'on' in DISPLAY_PHY_STATUS.
When initially powering up the PHY it performs various internal
calibrations for which it fully powers up. That means that if we check
for the expetected power state immediately upon releasing cmnreset we
would get the occasional false positive. But we can of course
poll until the expected value appears. It shouldn't be too long so
this shouldn't make modesets substantially longer.
One extra complication is introduced when we cross the streams, ie.
drive port B with pipe B. In this case we trick CL2 (where the DPLL lives)
into life by temporaily powering up the lanes in the second channel,
and once the pipe is up and runnign we release the lane power override.
At that point the power state of CL2 has somehow gotten entangled with
the power state of the first channel. That means that constructing the
expected DISPLAY_PHY_STATUS value is a bit tricky since based on the
lane power states in the second channel, CL2 should also be powered
down. But we can use the DPLL enable bit to determine when CL2 should
be alive even if the lanes are powered down. However the power state
of CL2 isn't actually tied in with the DPLL state, but to the state
of the lanes in first channel, so we have to avoid checking the
expected state between shutting down the DPLL and powering down
the lanes in the first channel. So no calling assert_chv_phy_status()
before the DISPLAY_PHY_CONTROL write in chv_phy_powergate_lanes(),
but after the write is a safe time to check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add some checks that the state of the DPIO lanes is more or less what we
expect based on the overrides.
The hardware only provides two bits per channel indicating whether all
or some of the lanes are powered down, so we can't do an exact check.
Additionally, CL2 powering down before we can check it adds another
twist. To work around this we simply check for the 0 value of the
CL2 register (which is what we get when it's powered down) and
adjust our expectations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can choose to leave the display PHY CL2 powerdown up to some hardware
signals, or we can force it. The BXT code forces the nonexistent CL2 in
the x1 PHY to power down. Follow suit on CHV. Maybe it can still save
some extra power by disabling some extra logic in CL1, or something.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has supports some form of automagic clock gating for the
DPIO SUS clock. We can simply enable the magic bits and the
hardware should take care of the rest.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: fix one error found by checkpath.pl
v3: Add one ignored break for switch-case. DDI-E hotplug
function doesn't work after updating drm-intel tree,
I checked the code and found this missing which isn't
the root cause for broke DDI-E hp. The broken
DDI-E hp function is fixed by "Adding DDI_E power
well domain".
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Timo Aaltonen <timo.aaltonen@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM instructions are not really
variable length instructions unlike MI_LOAD_REGISTER_IMM where it expects
(reg, addr) pairs so use fixed length for these instructions.
v2: rebase
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Appease checkpatch as Mika spotted in i915_reg.h - it seems
terminally unhappy about i915_cmd_parser.c so that would be a separate
patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turn on interrupt steering to route necessary interrupts to GuC.
v6:
Rebased
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fetches the required firmware image from the filesystem,
then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by
Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilson
v3:
Removed 'wait' parameter to intel_guc_ucode_load() as firmware
prefetch is no longer supported in the common firmware loader,
per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.
v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter]
Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]
v5:
Clarify WOPCM-related #defines [Tom O'Rourke]
Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call to intel_guc_ucode_init() later, so that it can
allocate GEM objects, and have it fetch the firmware; then
intel_guc_ucode_load() doesn't need to fetch it later.
[Daniel Vetter].
v6:
Update comment describing intel_guc_ucode_load() [Tom O'Rourke]
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak