On Qcom SD Card controller POWER, CLKCTRL, DATACTRL and COMMAND registers
should be updated in MCLK domain, and writes to these registers must be
separated by three MCLK cycles. This resitriction is not applicable for
other registers. Any subsequent writes to these register will be ignored
until 3 MCLK have passed.
One usec delay between two CMD register writes is not sufficient in the
card identification phase where the CCLK is very low. This patch replaces
a static 1 usec delay to use mmci_reg_delay function which can provide
correct delay depending on the cclk frequency.
Without this patch the card is not detected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch replaces a constant used in calculating timeout with a proper
macro. This is make code more readable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core:
- support HS400 mode of eMMC 5.0, via DT bindings mmc-hs400-1_{2,8}v
- if card init at 3.3v doesn't work, try 1.8v and 1.2v too
Drivers:
- moxart: New driver for MOXA ART SoCs
- rtsx_usb_sdmmc: New driver for Realtek USB card readers
- sdhci: Large rework around IRQ/regulator handling, remove card_tasklet
- sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
- sunxi: New driver for Allwinner sunxi SoCs
- usdhi6rol0: New driver for Renesas SD/SDIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OZao
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.16:
Core:
- support HS400 mode of eMMC 5.0, via DT bindings mmc-hs400-1_{2,8}v
- if card init at 3.3v doesn't work, try 1.8v and 1.2v too
Drivers:
- moxart: New driver for MOXA ART SoCs
- rtsx_usb_sdmmc: New driver for Realtek USB card readers
- sdhci: Large rework around IRQ/regulator handling, remove card_tasklet
- sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
- sunxi: New driver for Allwinner sunxi SoCs
- usdhi6rol0: New driver for Renesas SD/SDIO controller"
* tag 'mmc-updates-for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (95 commits)
mmc: sdhci-s3c: use mmc_of_parse and remove the card_tasklet
mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller
mmc: sdhci-of-esdhc: Fixup compile error
mmc: tegra: fix reporting of base clock frequency
mmc: tegra: disable UHS modes
mmc: sdhci-dove: use mmc_of_parse() and remove card_tasklet CD handler
MAINTAINERS: mmc: Add path to git tree
mmc: dove: fix missing MACH_DOVE dependency
mmc: sdhci: SD tuning is broken for some controllers
mmc: sdhci-esdhc-imx: fix mmc ddr mode regression issue
mmc: sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
mmc: omap_hsmmc: split omap-dma header file
mmc: omap_hsmmc: fix cmd23 multiblock read/write
mmc: omap_hsmmc: use devm_ioremap_resource
mmc: omap_hsmmc: use devm_request_threaded_irq
mmc: omap_hsmmc: use devm_request_irq
mmc: omap_hsmmc: use devm_clk_get
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
mmc: wmt-sdmmc: Use GFP_KERNEL instead of hard-coded value
mmc: omap: Use DIV_ROUND_UP instead of open coded
...
Remove the option to provide DMA configuration as platform data,
enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Remove the option to provide the flags for mmc capabilities as platform
data, enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the option to provide signal direction configuration and
feeback clock as platform data, enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is pure software configuration, which mmci has been supporting for
a while. Let's enable it as default so we can take benefit from it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let mmci DT parser only handle the specific bindings related to mmci
and extend the DT support by converting to the common mmc DT parser.
While both DT and platform data exist, DT takes precedence. If there
are supplied DT data, the card detect and write protect GPIOS are
enforced to be provided through it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ST Micro variant supports the option of using a feedback clock signal in
favor of the clockout pin when latching incoming signals on the data bus.
Since this is matter of how pins are being routed we need to provide a new DT
binding to be able to configure this through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Some variants have support for indicating the bus signal directions,
which currently are configured through platform data.
Add corresponding DT bindings to enable us to move away from using the
platform data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
To avoid duplication of code while handling card detect and write
protect GPIO pins/irqs, let's convert to use the mmc gpio API.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For CONFIG_PM_SLEEP, the device were always left in full power state
after system suspend.
We solely relied on a power domain to put it into low power state,
which is an unreasonable requirement to put on SOCs to implement.
Especially for those SOCs not supporting power domains at all.
Use pm_runtime_force_suspend|resume() as the system suspend callbacks,
to resolve the issue.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In runtime suspended state, we are not expecting IRQs and thus we can
safely mask them, not only for pwrreg_nopower variants but for all.
Obviously we then also need to make sure we restore the IRQ mask while
becoming runtime resumed.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Added MMC_DDR52 as eMMC's DDR mode distinguished from SD-UHS.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The ux500 variants have HW busy detection support, which is indicated
by the busy_detect flag. For these variants let's enable the
MMC_CAP_WAIT_WHILE_BUSY flag and add the support for it.
The mmc core will provide the RSP_BUSY command flag for those requests
we should care about busy detection. Regarding the max_busy_timeout,
the HW don't support busy detection timeouts so at this initial step
let's make it simple and set it to zero to indicate we are able to
support any timeout.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
In case of a read operation both MCI_CMDRESPEND and MCI_DATAEND can be
set in the status register when entering the interrupt handler. This is
due to that the card start sending data before the host has
acknowledged the command response.
To resolve the issue for this scenario, we must start by handling the
CMD irq instead of the DATA irq. The reason is beacuse the completion
of the DATA irq will not respect the current command and then causing
it to be garbled.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=JDGc
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If a corresponding power domain exists for the device and it manages
to cut the domain regulator while the device is runtime suspended,
the IP loses it's registers context. We restore the context in the
.runtime_resume callback from the existing register caches to adapt
to this situation.
We also want to make sure the registers are in a known state while
restoring context in the case when the power domain did not drop the
power, since there are restrictions for the order of writing to these
registers. To handle this, we clear the registers in the
.runtime_suspend callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After a write to the MMCICLOCK register data cannot be written to this
register for three feedback clock cycles. Writes to the MMCIPOWER
register must be separated by three MCLK cycles. Previously no issues
has been observered, but using higher ARM clock frequencies on STE-
platforms has triggered this problem.
The MMCICLOCK register is written to in .set_ios and for some data
transmissions for SDIO. We do not need a delay at the data transmission
path, because sending and receiving data will require more than three
clock cycles. Then we use a simple logic to only delay in .set_ios and
thus we don't affect throughput performance.
Signed-off-by: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By optionally putting the pins into sleep state in the .runtime_suspend
callback we can accomplish two things. One is to minimize current leakage
from pins and thus save power, second we can prevent the IP from driving
pins output in an uncontrolled manner, which may happen if the power domain
drops the domain regulator.
When returning from idle, entering .runtime_resume callback, the pins
are restored to default state.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no need for every driver to fetch a pinctrl handle and to
select the default state. Instead this is handled by the device driver
core, thus we can remove this piece of code from mmci.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To verify a signal voltage switch at initialization of UHS cards the
.card_busy callback is used. For some of the ST-variants, card busy
detection on the DAT0 pin is supported.
We extend the variant struct with a busy_detect flag to indicate
support for it. A corresponding busy detect function, which polls the
busy status bit, is then set to the .card_busy callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a cache variable in the host struct that reflects the current data in
the MMCIDATACTRL register. This patch will not introduce any functional
change but instead provide an easy option to keep specific bits in the
register between each data transfer.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add .start_signal_voltage_switch callback to be able to support UHS cards.
The voltage switch requires the optional vqmmc regulator to exist since
the actual voltage switch will be performed directly on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We can not rely on regulator_is_enabled to decide whether to
enable|disable the regulator. It would mean that the reference
counter for it is not balanced properly.
Instead keep track of our internal state by using a new flag in
the host struct, so we can take correct decisions.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, if DMA information isn't passed from platform data, then DMA
will not be used. This patch allows DMA information obtained though Device
Tree to be used as well.
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support added for transmission of CMD23 during multi block read or
write. In order to activate this feature, MMC_CAP_CMD23 flag needs
to be enabled in the capabilities field. Note that CMD23 support is
mandatory to support features like reliable write, data tag, context
ID, packed command.
This patch is based upon a patch from Saugata Das.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update cclk to the acutal used value and copy it to the actual_clock
variable in the mmc host for debug purpose.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converting to devm_clk_get simplifies error handling in probe
and we can remove other corresponding calls to clk_put.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch suppresses the warning below:
drivers/mmc/host/mmci.c: In function ‘mmci_set_ios’:
drivers/mmc/host/mmci.c:1165:20: warning: ignoring return value of
‘regulator_enable’, declared with attribute warn_unused_result
[-Wunused-result]
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are currently two instances of the ios_handler being used.
Both of which mearly toy with some regulator settings. Now there
is a GPIO regulator API, we can use that instead, and lessen the
per platform burden. By doing this, we also become more Device
Tree compatible.
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The cookie is now used to indicate if dma_unmap_sg shall be
done in post_request. At DMA errors, the DMA job is immediately
not only terminated but also unmapped. To indicate that this
has been done the cookie is reset to zero. post_request will
thus only do dma_umap_sg for requests which has a cookie not set
to zero.
Some corresponding duplicated code could then be removed and
moreover some corrections at DMA errors for terminating the same
DMA job twice has also been fixed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Versatile Express IOFPGA as shipped on VECD 5.0 (bitfiles v108/208
and v116/216) contains a modified version of the PL180 MMCI, with
PeriphID Configuration value changed to 0x2.
This version adds an optional "hardware flow control" feature. When
enabled MMC card clock will be automatically disabled when FIFO is
about to over/underflow and re-enabled once the host retrieved some
data. This makes the controller immune to over/underrun errors caused
by big interrupt handling latencies.
This patch adds relevant device variant in the driver.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the ST Micro variant, the MMCICLOCK register must not be used to
gate the clock. Instead use MMCIPOWER register and by clearing the
PWR_ON bit to do this.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The amba bus is already performing same actions but for the apb_pclk.
So here we just make sure the clock to card is gated as well to save
more power. At runtime resume we will thus restore the clock again.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By using the mmc_regulator_get_supply API we are able to do some
cleanups of the regulator code. Additionally let the regulator
API handle the error printing.
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add MMC_PM_KEEP_POWER to pm_caps so SDIO clients are able
to use this option to prevent power off in suspend.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for DDR mode which may be used for the ux500v2 variant.
Corresponding capabilities to enable the DDR support must be set in
the platform struct to enable the functionality.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM updates from Russell King:
"Here's the updates for ARM for this merge window, which cover quite a
variety of areas.
There's a bunch of patch series from Will tackling various bugs like
the PROT_NONE handling, ASID allocation, cluster boot protocol and
ASID TLB tagging updates.
We move to a build-time sorted exception table rather than doing the
sorting at run-time, add support for the secure computing filter, and
some updates to the perf code. We also have sorted out the placement
of some headers, fixed some build warnings, fixed some hotplug
problems with the per-cpu TWD code."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (73 commits)
ARM: 7594/1: Add .smp entry for REALVIEW_EB
ARM: 7599/1: head: Remove boot-time HYP mode check for v5 and below
ARM: 7598/1: net: bpf_jit_32: fix sp-relative load/stores offsets.
ARM: 7595/1: syscall: rework ordering in syscall_trace_exit
ARM: 7596/1: mmci: replace readsl/writesl with ioread32_rep/iowrite32_rep
ARM: 7597/1: net: bpf_jit_32: fix kzalloc gfp/size mismatch.
ARM: 7593/1: nommu: do not enable DCACHE_WORD_ACCESS when !CONFIG_MMU
ARM: 7592/1: nommu: prevent generation of kernel unaligned memory accesses
ARM: 7591/1: nommu: Enable the strict alignment (CR_A) bit only if ARCH < v6
ARM: 7590/1: /proc/interrupts: limit the display of IPIs to online CPUs only
ARM: 7587/1: implement optimized percpu variable access
ARM: 7589/1: integrator: pass the lm resource to amba
ARM: 7588/1: amba: create a resource parent registrator
ARM: 7582/2: rename kvm_seq to vmalloc_seq so to avoid confusion with KVM
ARM: 7585/1: kernel: fix nr_cpu_ids check in DT logical map init
ARM: 7584/1: perf: fix link error when CONFIG_HW_PERF_EVENTS is not selected
ARM: gic: use a private mapping for CPU target interfaces
ARM: kernel: add logical mappings look-up
ARM: kernel: add cpu logical map DT init in setup_arch
ARM: kernel: add device tree init map function
...
Not all the architectures have readsl/writesl,
use the more portable ioread32_rep/iowrite32_rep functions instead.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fetches the pinctrl resource for the MMCI driver, and if
a "default" state is found, it is activated.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For writes, HWFC shall be switched off when transfer size <= 8
bytes and when MCLK rate is above 50 MHz. For 50MHz and below
it shall be switched off when transfer size < 8 bytes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For data writes <= 8 bytes, HW flow control was disabled but
never re-enabled when the transfer was completed. This meant
that a following read request would give buffer overrun errors.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clk_prepare_enable and clk_disable_unprepare combine clk_prepare and
clk_enable, and clk_disable and clk_unprepare. They make the code more
concise, and ensure that clk_unprepare is called when clk_enable fails.
A simplified version of the semantic patch that introduces calls to these
functions is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- clk_prepare(e);
- clk_enable(e);
+ clk_prepare_enable(e);
@@
expression e;
@@
- clk_disable(e);
- clk_unprepare(e);
+ clk_disable_unprepare(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the GPIOs used by the MMCI driver are not registered yet when the driver is
probe()d, they can't be used. This happens if the mmci driver is probed before
the respective GPIO controller (e.g. on the LPC32xx EA3250 board, the PCA9532
GPIO controller would be initialized via DT after mmci). Therefore, we defer
mmci in this case.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Zero is a valid GPIO and shouldn't be handled as an error return code from
of_get_named_gpio(). It was a leftover from old code before getting
pdata->gpio_*() was modified.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When booting with Device Tree enabled, platform specific information
is gathered by parsing the DT binary. Platform data is subsequently
populated with the result. The memory required for this is not
automatically allocated during Device Tree boot, so we'll do it here
instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Drivers:
- at91-mci: This driver will be replaced by atmel-mci in 3.7.
- atmel-mci: Add support for old at91-mci hardware.
- dw_mmc: Allow multiple controllers; this previously caused corruption.
- imxmmc: Remove this driver, replaced by mxcmmc.
- mmci: Add device tree support.
- omap: Allow multiple controllers.
- omap_hsmmc: Auto CMD12, DDR support.
- tegra: Support SD 3.0 spec.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPvtlQAAoJEHNBYZ7TNxYMxr8P/0oKBszCCpvYQVH9F7WxWdcs
haXcfvQBshKLTw8GxnJhNOuoMpDO565pLCxtL1NigFzA/nnvDrsGu03Rjy8vmeGT
vtuda+T+OVOmHwGx868fHMMtp3OeV0cyE2I9WQe0R1M0IW5YFpOCS3zzuaXofMlA
dYK6KJC0RlZnc/Usn4esQhXCBS3dH80ynMfORjNtHl2wDnuvp+k2DD2kB2SFmw0H
raieXeqcfGTqK9UYWqYYDvFM1D1FZcaokyYIs4Ut8WQtnKWSCWyMEqy5JjC1xbIr
YZs+08uIUEcGBnYAuuB6XDcmWfPInqTiStQ6lX6iO6msY8DNh9n2wjt5V30X9GWx
fVT8a27qB7gCf7D/ACRbGq+sgRjCL/2de4UcuH/wZyFu585lohinUqpZM6ODz7wA
7AyfPYixpegbYLrppESgzdWzDUFY5HFyhogI9JUemtI1etIvy/tH1n6+l0388Qmy
vYYV91U3ommxw4XgyFI2psJrl5y+XveEdv4q0NuqD5nkVrTDQ3cmp/vXXMfIo7fe
YliEQuOwV1DAUsvA+FgNKCTYDtHveKIacHVJtQqJcelUOn6Klxs0xgHvsAXgux8U
ZDLmAPrrg7O+YmDGsHC0lU8joaXQmtfauqVGm+JSSoQv4iSNI+SqwGaSTlzRURd5
12htXRTx0TTINOAs7vLH
=rjPa
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC changes from Chris Ball
- at91-mci: This driver will be replaced by atmel-mci in 3.7.
- atmel-mci: Add support for old at91-mci hardware.
- dw_mmc: Allow multiple controllers; this previously caused
corruption.
- imxmmc: Remove this driver, replaced by mxcmmc.
- mmci: Add device tree support.
- omap: Allow multiple controllers.
- omap_hsmmc: Auto CMD12, DDR support.
- tegra: Support SD 3.0 spec.
Fix up the usual trivial conflicts in feature-removal-schedule.txt
* tag 'mmc-merge-for-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (38 commits)
mmc: at91-mci: this driver is now deprecated
mmc: omap_hsmmc: pass IRQF_ONESHOT to request_threaded_irq
mmc: block: Allow disabling 512B sector size emulation
mmc: atmel-mci: add debug logs
mmc: atmel-mci: add support for version lower than v2xx
mmc: atmel-mci: change the state machine for compatibility with old IP
mmc: atmel-mci: the r/w proof capability lack was not well managed
mmc: dw_mmc: Fixed sdio interrupt mask bit setting bug
mmc: omap: convert to module_platform_driver
mmc: omap: make it behave well as a module
mmc: omap: convert to per instance workqueue
mmc: core: Remove dead code
mmc: card: Avoid null pointer dereference
mmc: core: Prevent eMMC VCC supply to be cut from late init
mmc: dw_mmc: make multiple instances of dw_mci_card_workqueue
mmc: queue: remove redundant memsets
mmc: queue: rename mmc_request function
mmc: core: skip card initialization if power class selection fails
mmc: core: fix the signaling 1.8V for HS200
mmc: core: fix the decision of HS200/DDR card-type
...
error: implicit declaration of function 'mmci_dt_populate_generic_pdata'
This is due to the '#if CONFIG_OF' guards placed around
mmci_dt_populate_generic_pdata(), but not around the call to it. We
repair this by inserting a stub which elegantly returns when CONFIG_OF
is not set.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now there are irqdomains in place for Snowball, we can request GPIO
IRQs directly by their binding. This replaces the previous method
of hard-coding the hwirq using u32 values in the DT.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide a means to collect attributes specific to ST-Ericsson's ux500
variant series. This patch registers itself as the AMBA driver to be
called during the probe process. Once all attributes and ux500 specifics
are are collected the normal mmci core probe is called.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The Nomadik variant is somewhere inbetween the U300 and the Ux500
variant, its actually expose the same primecell ID as the U300
but had different characteristics so it needs a small revision
bump and hard-coding from the board/device tree. After this it
works just fine.
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
Pull #2 ARM updates from Russell King:
"Further ARM AMBA primecell updates which aren't included directly in
the previous commit. I wanted to keep these separate as they're
touching stuff outside arch/arm/."
* 'amba' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7362/1: AMBA: Add module_amba_driver() helper macro for amba_driver
ARM: 7335/1: mach-u300: do away with MMC config files
ARM: 7280/1: mmc: mmci: Cache MMCICLOCK and MMCIPOWER register
ARM: 7309/1: realview: fix unconnected interrupts on EB11MP
ARM: 7230/1: mmc: mmci: Fix PIO read for small SDIO packets
ARM: 7227/1: mmc: mmci: Prepare for SDIO before setting up DMA job
ARM: 7223/1: mmc: mmci: Fixup use of runtime PM and use autosuspend
ARM: 7221/1: mmc: mmci: Change from using legacy suspend
ARM: 7219/1: mmc: mmci: Change vdd_handler to a generic ios_handler
ARM: 7218/1: mmc: mmci: Provide option to configure bus signal direction
ARM: 7217/1: mmc: mmci: Put power register deviations in variant data
ARM: 7216/1: mmc: mmci: Do not release spinlock in request_end
ARM: 7215/1: mmc: mmci: Increase max_segs from 16 to 128
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
For simple modules that contain a single amba_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro, module_amba_driver(),
which replaces the module_init()/module_exit() registrations with
template functions.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a system with large pages (64k in my case), the following BUG is
triggered in MMC core:
[ 2.338023] BUG: failure at drivers/mmc/core/core.c:221/mmc_start_request()!
[ 2.338102] Kernel panic - not syncing: BUG!
[ 2.338155] Call trace:
[ 2.338228] [<ffffffc00008635c>] dump_backtrace+0x0/0x120
[ 2.338317] [<ffffffc0003365ec>] dump_stack+0x14/0x1c
[ 2.338403] [<ffffffc000336990>] panic+0xbc/0x1f0
[ 2.338498] [<ffffffc00027a494>] mmc_start_request+0x154/0x184
[ 2.338600] [<ffffffc00027abdc>] mmc_start_req+0x110/0x140
[ 2.338701] [<ffffffc00028604c>] mmc_blk_issue_rw_rq+0x7c/0x39c
[ 2.338804] [<ffffffc00028652c>] mmc_blk_issue_rq+0x1c0/0x468
[ 2.338905] [<ffffffc000287564>] mmc_queue_thread+0x68/0x118
[ 2.338995] [<ffffffc0000bc308>] kthread+0x84/0x8c
This is because of a 64k request with a max_req_size of 64k-1 bytes.
The following patch fixes the problem by limiting the max_blk_count
such that max_blk_count * max_blk_size == max_req_size. I couldn't
pursuade the compiler to emit a shift instead of a div without encoding
the shift explicitly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Instead of reading a register value everytime we need to
apply a new value for it, maintain a cached copy for it.
This also means we are able to skip writes that are not
needed.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Corrects a bug in MMCI host driver which silently causes
small reads (< 4 bytes as only used in SDIO) from PL-18X to fail.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the SDIO preparation to be done before the DMA job is setup.
This makes it possible to do DMA for SDIO transfers as well as the
earlier supported pio mode.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added use of runtime PM autosuspend feature, with a fixed
timeout of 50 ms. This will prevent adding a latency,
although very minor, for _every_ request.
Moreover the runtime_get_sync is now also used in set_ios and
suspend since the runtime resourses are needed here as well.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch switch from using the legacy suspend/resume
to the new way of registering PM callbacks. No functional
change is done.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The purpose of the vdd_handler does not make sense. We remove it
and use a generic approach instead. A new ios_handler is added, the
purpose of which e.g. can be to control GPIO pins to a levelshifter.
Previously the vdd_handler was also used for making additional
changes to the power register bits. This option is superfluous and is
therefore removed.
Adaptaptions from the old vdd_handler to the new ios_handler is done for
mach-ux500 board, which was the only one using the vdd_handler.
This patch is based upon a patch from Sebastian Rasmussen.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ST Micro variant supports bus signal direction indication. A new
member in the variant struct is added for this.
Moreover the actual signal direction configuration is board specific,
thus the amba mmci platform data is extended with a new member to be
able provide mmci with these specific board configurations.
This patch is based upon a patch from Sebastian Rasmussen.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use variant data to store hardware controller deviations concerning
power registers to improve readability of the code.
Signed-off-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch "mmc: core: move ->request() call from atomic context",
is the reason to why this change is possible. This simplifies the
error handling code execution path quite a lot and potentially also
fixes some error handling hang problems.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LJnN
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
MMC highlights for 3.3:
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
* tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (58 commits)
mmc: fix a deadlock between system suspend and MMC block IO
mmc: sdhci: restore the enabled dma when do reset all
mmc: dw_mmc: miscaculated the fifo-depth with wrong bit operation
mmc: host: Adds support for eMMC 4.5 HS200 mode
mmc: core: HS200 mode support for eMMC 4.5
mmc: dw_mmc: fixed wrong bit operation for SDMMC_GET_FCNT()
mmc: core: Separate the timeout value for cache-ctrl
mmc: sdhci-spear: Fix compilation error
mmc: sdhci: Deal with failure case in sdhci_suspend_host
mmc: dw_mmc: Clear the DDR mode for non-DDR
mmc: sd: Fix SDR12 timing regression
mmc: sdhci: Fix tuning timer incorrect setting when suspending host
mmc: core: Add option to prevent eMMC sleep command
mmc: omap_hsmmc: use threaded irq handler for card-detect.
mmc: sdhci-pci: enable runtime PM for Medfield SDIO
mmc: sdhci: Always pass clock request value zero to set_clock host op
mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION
mmc: sdhci-pci: get gpio numbers from platform data
mmc: sdhci-pci: add platform data
mmc: sdhci: prevent card detection activity for non-removable cards
...
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
When getting a cmd irq during an ongoing data transfer
with dma, the dma job were never terminated. This is now
corrected.
Cc: <stable@vger.kernel.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The interrupt was previously enabled and then correctly cleared.
Now we also handle it correctly.
Cc: <stable@vger.kernel.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves mmc drivers to use new enum
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The error condition indicates that mmci_post_request() should cleanup
after the mmci_pre_request(). In this case the resources allocated by
device_prep_slave_sg() are freed by calling dmaengine_terminate_all().
dma_unmap_sg() should always be performed if the host_cookie is set.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add runtime PM support to the MMCI primecell driver, making use of
the core primecell bus runtime PM support.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
pre_req() runs dma_map_sg() and prepares the dma descriptor for the next
mmc data transfer. post_req() runs dma_unmap_sg. If not calling pre_req()
before mmci_request(), mmci_request() will prepare the cache and dma just
like it did it before. It is optional to use pre_req() and post_req()
for mmci.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The ARM version maximum clock divider is 512 whereas for the ST
variants it's 257. Let's use DIV_ROUND_UP() for both cases so we
can see clearly what's going on here.
[Use DIV_ROUND_UP to clarify elder code]
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stresstesting insert/remove of SD-cards can trigger
a StartBitErr. This made the driver to hang in forever
waiting for a non ocurring data timeout.
This bit and interrupt is documented in the original
PL180 TRM, just never implemented until now.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Right now the card detect IRQ for MMCI is requested without any
flags which will give some default machine-specified IRQ
behaviour. However on the U300 rising+falling edges (such as can
be expected from a simple GPIO to generate when inserting/removing
a card) need to be requested explicitly.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Ulf Hansson <ulf.hansson@stericsson.com>
Cc: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Srinivas Kandagatla