The following GigaDevice chips have the QE BIT in the feature flags, I
checked the datasheets, but did not try this.
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
The Quad operations like 0xEB mention that the QE bit has to be set.
Fixes: c93c613214 ("mtd: spinand: add support for GigaDevice GD5FxGQ4xA")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200820165121.3192-3-hauke@hauke-m.de
The datasheet only lists one dummy byte in the 0xEH operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Fixes: c93c613214 ("mtd: spinand: add support for GigaDevice GD5FxGQ4xA")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200820165121.3192-2-hauke@hauke-m.de
vf610_nfc_probe() does not invoke clk_disable_unprepare() on one error
handling path. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 6f0ce4dfc5 ("mtd: rawnand: vf610: Avoid a potential NULL pointer dereference")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200806072634.23528-1-novikov@ispras.ru
The Macronix MX31UF1GE4BC is a 1.8V, 1Gbit (128MB) serial
NAND flash device.
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1595404978-31079-3-git-send-email-ycllin@mxic.com.tw
The Macronix MX31LF1GE4BC is a 3V, 1Gbit (128MB) serial
NAND flash device.
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1595404978-31079-2-git-send-email-ycllin@mxic.com.tw
The sparse tool complains as follows:
drivers/mtd/nand/raw/pasemi_nand.c:71:5: warning:
symbol 'pasemi_device_ready' was not declared. Should it be static?
This function is not used outside of pasemi_nand.c, so this commit
marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200721151657.41027-1-weiyongjun1@huawei.com
Now that exec_op() is implemented, we can get rid of all the legacy
hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-7-tudor.ambarus@microchip.com
Use the nand_{write,read}_data_op() helpers instead of calling the
atmel_nand_{read,write}_buf() functions directly. This will ease the
transition to exec_op().
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-4-tudor.ambarus@microchip.com
No need to enable it everytime select_chip() is called. If we really
care about PM, we should implement runtime PM hooks and disable the
controller and all its clocks when the controller has been unused for
some time.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-2-tudor.ambarus@microchip.com
Many helpers are generic to all NAND chips, they should not be
raw-NAND specific, so use the generic ones.
To avoid moving all the raw NAND core "history" into the generic NAND
layer, we keep a part of this parsing in the raw NAND core to ensure
backward compatibility.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-20-miquel.raynal@bootlin.com
AM654 HyperBus controller provides MMIO interface to read data from
flash. So add DMA memcpy support for reading data over MMIO interface.
This provides 5x improvement in throughput and reduces CPU usage as
well.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-5-vigneshr@ti.com
Recent genpd changes for K3 platform ensure device is ON before driver
probe is called. Therefore, drop redundant pm_runtime_* calls from
driver to simplify the code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-4-vigneshr@ti.com
Setting up of direct mapping should be done with flash node's IO
address space and not with controller's IO region.
Fixes: b6fe8bc67d ("mtd: hyperbus: move direct mapping setup to AM654 HBMC driver")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-3-vigneshr@ti.com
Add support Winbond w25q{64,128,256}jwm which are identical to existing
w25q32jwm except for their sizes.
This was tested with w25q64jwm, basic erase/write/readback and
lock/unlock both lower/upper blocks were okay.
Signed-off-by: ikjn@chromium.org <ikjn@chromium.org>
Signed-off-by: Xingyu Wu <wuxy@bitland.corp-partner.google.com>
Signed-off-by: ST Lin <stlin2@winbond.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200928060631.2090541-1-ikjn@chromium.org
Intel Alder Lake-S has the same SPI serial flash controller as Cannon
Lake. Add Alder Lake-S PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200925095109.51148-1-mika.westerberg@linux.intel.com
On my system the spi_nor_probe() took ~6 ms at bootup. That's not a
lot, but every little bit adds up to a slow bootup. While we can get
this out of the boot path by making it a module, there are times where
it is convenient (or even required) for this to be builtin the kernel.
Let's set that we prefer async probe so that we don't block other
drivers from probing while we are probing.
This is a tiny little change that is almost guaranteed to be safe for
anything that is able to run as a module, which SPI_NOR is.
Specifically modules are already probed asynchronously. Also: since
other things in the system may have enabled asynchronous probe the
system may already be doing other things during our probe.
There is a small possibility that some other driver that was a client
of SPI_NOR didn't handle -EPROBE_DEFER and was relying on probe
ordering and only worked when the SPI_NOR and the SPI bus were
builtin. In that case the other driver has a bug that's waiting to
hit and the other driver should be fixed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200902160002.1.I658d1c0db9adfeb9a59bc55e96a19e192c959e55@changeid
Mechanical switch from the legacy "mode" enumeration to the new
"engine type" enumeration in drivers and board files.
The device tree parsing is also updated to return the new enumeration
from the old strings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-11-miquel.raynal@bootlin.com
The use of "syndrome" placement should not be encoded in the ECC
engine mode/type.
Create a "placement" field in NAND chip and change all occurrences of
the NAND_ECC_HW_SYNDROME enumeration to be just NAND_ECC_HW and
possibly a placement entry like NAND_ECC_PLACEMENT_INTERLEAVED.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-10-miquel.raynal@bootlin.com
Set up a readahead size by default, as very few users have a good
reason to change it. This means code, ecryptfs, and orangefs now
set up the values while they were previously missing it, while ubifs,
mtd and vboxsf manually set it to 0 to avoid readahead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Acked-by: Richard Weinberger <richard@nod.at> [ubifs, mtd]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A detach hung is possible when a race occurs between the detach process
and the ubi background thread. The following sequences outline the race:
ubi thread: if (list_empty(&ubi->works)...
ubi detach: set_bit(KTHREAD_SHOULD_STOP, &kthread->flags)
=> by kthread_stop()
wake_up_process()
=> ubi thread is still running, so 0 is returned
ubi thread: set_current_state(TASK_INTERRUPTIBLE)
schedule()
=> ubi thread will never be scheduled again
ubi detach: wait_for_completion()
=> hung task!
To fix that, we need to check kthread_should_stop() after we set the
task state, so the ubi thread will either see the stop bit and exit or
the task state is reset to runnable such that it isn't scheduled out
indefinitely.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Cc: <stable@vger.kernel.org>
Fixes: 801c135ce7 ("UBI: Unsorted Block Images")
Reported-by: syzbot+853639d0cb16c31c7a14@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
As the only user has been removed in previous patch, let's revert
this one together.
This reverts commit be192209d5.
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-2-git-send-email-yangyicong@hisilicon.com
Previous patch intends to restore the flash's QE bit when removed/shutdown,
but may have some problems and break the flash:
- for those originally in Quad mode, this patch will clear the QE bit
when unloaded the flash, which is incorrect.
- even with above problem solved, it may still break the flash as some
flash's QE bit is non-volatile and lots of set/reset will wear out
the bit.
- the restore method cannot be proved to be valid as if a hard
reset or accident crash happened, the spi_nor_restore() won't be
performed the the QE bit will not be restored as we expected to.
So let's revert it to fix this. The discussion can be found at [1].
This reverts commit cc59e6bb6c.
[1] https://lore.kernel.org/linux-mtd/CAO8h3eFLVLRmw7u+rurKsg7=Nh2q-HVq-HgVXig8gf5Dffk8MA@mail.gmail.com/
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-1-git-send-email-yangyicong@hisilicon.com
Variable 'size' is being assigned the value zero that will never be
read. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200910154451.752569-1-colin.king@canonical.com
If calling mtdoops_write, don't also schedule work to be done later.
Although this appears to not be causing an issue, possibly because the
scheduled work will never get done, it is confusing.
Fixes: 016c1291ce ("mtd: mtdoops: do not use mtd->panic_write directly")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200903034217.23079-1-mark.tomlinson@alliedtelesis.co.nz
Create a generic ECC engine framework. This is a base to instantiate ECC
engine objects.
If we really want to be generic, bindings must evolve, so here is the
new logic. The following three properties are mutually exclusive:
- The nand-no-ecc-engine boolean property is set and there is no
ECC engine to retrieve.
- The nand-use-soft-ecc-engine boolean property is set and the core
will force using the use of software correction.
- There is a nand-ecc-engine property pointing at a node which will
act as ECC engine.
It the later case, the property may reference:
- The NAND chip node itself (for the on-die ECC case).
- The parent node if the NAND controller embeds an ECC engine.
- Any other node being an external ECC controller as well.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-9-miquel.raynal@bootlin.com
Allows a mtdconcat's subdevice->_panic_write to be used for
capturing a mtdoops dump.
Note: The ->_panic_write is mapped through from the first chip
that is part of the concat virtual device.
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
[miquel.raynal@bootlin.com: return err, not void]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200602143403.13465-1-matthew.weber@rockwellcollins.com
Building lpddr2_nvm with clang can result in a giant stack usage
in one function:
drivers/mtd/lpddr/lpddr2_nvm.c:399:12: error: stack frame size of 1144 bytes in function 'lpddr2_nvm_probe' [-Werror,-Wframe-larger-than=]
The problem is that clang decides to build a copy of the mtd_info
structure on the stack and then do a memcpy() into the actual version. It
shouldn't really do it that way, but it's not strictly a bug either.
As a workaround, use a static const version of the structure to assign
most of the members upfront and then only set the few members that
require runtime knowledge at probe time.
Fixes: 96ba9dd657 ("mtd: lpddr: add driver for LPDDR2-NVM PCM memories")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200505140136.263461-1-arnd@arndb.de
In physmap_flash_of_init() the maps[].name can be populated based on the
optional 'linux,mtd-name' property in the dts. Make sure this is
retained when filling in the rest of the map[] data.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200824025744.25992-1-chris.packham@alliedtelesis.co.nz
Function print_drs_error is only used in drivers/mtd/lpddr/lpddr_cmds.c
so, better to move it there.
Also, notice that there's no need for inline as the function is used
once. Lastly, fix the following checkpatch warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
+static void print_drs_error(unsigned dsr)
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/e0063cbd65f3b47be1db34efc494ea3047634d88.1588016644.git.gustavo@embeddedor.com
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
JFFS2:
- Fix for a corner case while mounting
- Fix for an use-after-free issue
UBI:
- Fix for a memory load while attaching
- Don't produce an anchor PEB with fastmap being disabled
UBIFS:
- Fix for orphan inode logic
- Spelling fixes
- New mount option to specify filesystem version
-----BEGIN PGP SIGNATURE-----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=iztS
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fix for a corner case while mounting
- Fix for an use-after-free issue
UBI:
- Fix for a memory load while attaching
- Don't produce an anchor PEB with fastmap being disabled
UBIFS:
- Fix for orphan inode logic
- Spelling fixes
- New mount option to specify filesystem version"
* tag 'for-linus-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: fix UAF problem
jffs2: fix jffs2 mounting failure
ubifs: Fix wrong orphan node deletion in ubifs_jnl_update|rename
ubi: fastmap: Free fastmap next anchor peb during detach
ubi: fastmap: Don't produce the initial next anchor PEB when fastmap is disabled
ubifs: misc.h: delete a duplicated word
ubifs: add option to specify version for new file systems
* Spelling
* http to https updates
NAND core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
* Disable Quad Mode in spi_nor_restore().
* Don't abort BFPT parsing when QER reserved value is used.
* Add support/update capabilities for few flashes.
* Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
* Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
* Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
* intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl8vJtMACgkQJWrqGEe9
VoRdGAf/Y5m5BwmLilkEYpffyxi7dVR6XOKPLU5EJXkS3dPvH9398zchbHOdedCZ
OzJIfh6Iv+qbkgS2g0lAAT+SAfOfG9plubvSdkjrHXl4eZXRnR/49RF5LAEju7sz
Uw1HdRcawyEi5uI9yYS0tCeVMIUJq+5x7VibH+82yOIdSPc60c7FDc5ih/nVKj/a
Pn9LOzGzkdndcE1b3FcF2Uk/T1YOJx3Yt5ngALlPpJxaDZmQSHtYPuuz8DfUbamf
uj3CkpqYRyT18CzuFvtuba6LyF+donXNJgvl6ivW7dlRSPzSMnDQu7J5bpNhUfcd
p/ZdzX1Jxle4theDm0J9ALsSSM5g2w==
=RiY8
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Spelling
- http to https updates
NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4,
TC58NVG0S3E, and TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which is
critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts during
the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was taken
through the SPI tree. Merge it also in spi-nor/next to avoid
conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't support
it.
- Fix performance regression"
* tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (79 commits)
MTD: pfow.h: drop a duplicated word
MTD: mtd-abi.h: drop a duplicated word
mtd: rawnand: omap_elm: Replace HTTP links with HTTPS ones
mtd: Replace HTTP links with HTTPS ones
mtd: hyperbus: Replace HTTP links with HTTPS ones
mtd: revert "spi-nor: intel: provide a range for poll_timout"
mtd: spi-nor: update read capabilities for w25q64 and s25fl064k
mtd: spi-nor: micron: Add SPI_NOR_DUAL_READ flag on mt25qu02g
mtd: spi-nor: macronix: Add support for mx66u2g45g
mtd: spi-nor: intel-spi: Simulate WRDI command
mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
mtd: spi-nor: Add capability to disable flash quad mode
mtd: spi-nor: spansion: Remove s70fl01gs from flash_info
mtd: spi-nor: sfdp: do not make invalid quad enable fatal
dt-bindings: mtd: fsl-upm-nand: Deprecate chip-delay and fsl, upm-wait-flags
mtd: rawnand: stm32_fmc2: get resources from parent node
mtd: rawnand: stm32_fmc2: use regmap APIs
memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver
dt-bindings: memory-controller: add STM32 FMC2 EBI controller documentation
dt-bindings: mtd: update STM32 FMC2 NAND controller documentation
...
Pull misc vfs updates from Al Viro:
"No common topic whatsoever in those, sorry"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: define inode flags using bit numbers
iov_iter: Move unnecessary inclusion of crypto/hash.h
dlmfs: clean up dlmfs_file_{read,write}() a bit
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl8s85cACgkQJWrqGEe9
VoTrdwgAqphDYjtYNaI+1F0YQdIy/l8ddVmc5NwhKpiitKh0APDFDrdV5CwQaENO
9wWHJJPpT7xXPnEaq2+OWlPt2HpnEI4a+IRvySc9lr+MfkdY9ubo3B2wX7jBueKr
WoVDAGe8Ua1FkPOeDy7Qe+H1bQPha8fvyfb7x2h8uCYrrIkDJaMilorzHVnuXfCg
t5QJXRuznmYjUfMKOgLDjX3r79IJ+5mcrJIvMgHOyQIoG4Aao7lHIr2f01O50HWy
JKqQD3QhPR8lJGaEW485s+H+gnnNQW8Y1+8u3bhauEg/6Ddx2oksUIBTME8HUUuK
kAXrQ+KEs37l1a6pyaMBHaWU18T/oQ==
=hn04
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity. This pull
request includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the memory
subsystem doesn't seem to have a fixed maintainer at the minute and this
seemed like the most sensible way to get that hardware supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm GENI,
sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8oBFoTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0P2UB/47NlDsAadOiOB0ZzPKdn4Nr5BLvUza
TP63gAsxD4BErzgf/p/0D8qUTZPzmlfA833gj9hkIavJlTmv3fGrH0XeHg2OuCJb
yhyw9pE7MPpnARVOJHz1MZkAT/dY+sF3TaUXysmymlvs6CLqRnsLTOwK2f92SeGH
ygpC4J1tfD961xWmv2Zt8wNuQXtH+JePLXeZFSx2ZkpToFT56QO6kFpWjVfDquY4
/F8bc7qyXX6FcsBYAG6Ly35OSxbPazVLkTaDWQr5V4TAD0DXw0NOyvxg2OccqE31
y1jjx3hn98sN73m/VLzlEOer4w9313K5BOISaN0z7TQSQ55XRZKe4EQj
=K1PB
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity.
This includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the
memory subsystem doesn't seem to have a fixed maintainer at the minute
and this seemed like the most sensible way to get that hardware
supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm
GENI, sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1"
* tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (119 commits)
dt-bindings: lpspi: New property in document DT bindings for LPSPI
spi: lpspi: fix using CS discontinuously on i.MX8DXLEVK
spi: lpspi: remove unused fsl_lpspi->chipselect
spi: lpspi: Fix kernel warning dump when probe fail after calling spi_register
spi: rockchip: Fix error in SPI slave pio read
spi: rockchip: Support 64-location deep FIFOs
spi: rockchip: Config spi rx dma burst size depend on xfer length
spi: spi-topcliff-pch: drop call to wakeup-disable
spi: spidev: Align buffers for DMA
spi: correct kernel-doc inconsistency
spi: sun4i: update max transfer size reported
spi: imx: enable runtime pm support
spi: update bindings for MT8192 SoC
spi: mediatek: add spi support for mt8192 IC
spi: Add bindings for Lightning Mountain SoC
spi: lantiq: Add support to Lightning Mountain SoC
spi: lantiq: Move interrupt configuration to SoC specific data structure
spi: lantiq: Add fifo size bit mask in SoC specific data structure
spi: lantiq: Add support to acknowledge interrupt
spi: lantiq: Move interrupt control register offesets to SoC specific data structure
...
ubi_wl_entry related with the fm_next_anchor PEB is not freed during
detach, which causes a memory leak.
Don't forget to release fm_next_anchor PEB while detaching ubi from
mtd when CONFIG_MTD_UBI_FASTMAP is enabled.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Fixes: 4b68bf9a69 ("ubi: Select fastmap anchor PEBs considering...")
Signed-off-by: Richard Weinberger <richard@nod.at>
Following process triggers a memleak caused by forgetting to release the
initial next anchor PEB (CONFIG_MTD_UBI_FASTMAP is disabled):
1. attach -> __erase_worker -> produce the initial next anchor PEB
2. detach -> ubi_fastmap_close (Do nothing, it should have released the
initial next anchor PEB)
Don't produce the initial next anchor PEB in __erase_worker() when fastmap
is disabled.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: f9c34bb529 ("ubi: Fix producing anchor PEBs")
Reported-by: syzbot+d9aab50b1154e3d163f5@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl8f/IUACgkQS1VPR6WN
FOk8nQf/ReDFzgrZGPRXK8MbcWdmrNQo5cGwCs2zuKskvWMdgNZC92DTlgrMmx+d
NQ/0PpsOHZJ1bcPjlsxccSQNrFnSzxr91n8NJIQ6DuralCN+x9Zh4dtox0Q0WB1x
d9y+I65EpSyEHRhWRW1y2sq5xRlwiANWVQPfIUN10q/flz9CI5Q8gY8wdUQT4Q5x
/ER7CMSbZSehnxHnJ9kSFDRhJCobDKnOdsFLDVZFPseQZzXYe5zP0J/T5S63wem2
/QFKSCfcI4UqMbeurGpQok9ZywCUp+SUG2mAld/yTig+YCCeY1Dp45IGJZ7eKDky
NPYjVYaRlvWwcTgS1OdCThGd+F29Ug==
=YZOZ
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
Both w25q64 and s25fl064k nor flash support QUAD and DUAL read
command, hence update the same in flash_info table.
This is tested on Broadcom Stingray SoC (bcm958742t).
s25fl064k and w25q64 share the same JEDEC ID. The search alg will
return the first hit, so s25fl064k even for the winbond parts. We
should differentiate between these flashes, but it's not in the
scope of this patch. Related discussion at:
Link: https://lore.kernel.org/patchwork/patch/628090/
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200529071655.739-1-rayagonda.kokatanur@broadcom.com
[tudor.ambarus@microchip.com: Update commit message and indicate that
s25fl064k and w25q64 share the same JEDEC ID]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Micron mt25qu02g supports both x2 and x4 transactions. Add the
SPI_NOR_DUAL_READ flag to its spi_nor_ids[] table entry.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-3-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Macronix mx66u2g45g is a 1.8V, 2Gbit (256MB) device that
supports x1, x2, or x4 operation.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-2-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
After spi_nor_write_disable() return code checks were introduced in the
spi-nor front end intel-spi backend stopped to work because WRDI was never
supported and always failed.
Just pretend it was sucessful and ignore the command itself. HW sequencer
shall do the right thing automatically, while with SW sequencer we cannot
do it anyway, because the only tool we had was preopcode and it makes no
sense for WRDI.
Fixes: bce679e5ae ("mtd: spi-nor: Check for errors after each Register Operation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/282e1305-fd08-e446-1a22-eb4dff78cfb4@nokia.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When doing a "write" ioctl call, properly check that we have permissions
to do so before copying anything from userspace or anything else so we
can "fail fast". This includes also covering the MEMWRITE ioctl which
previously missed checking for this.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[rw: Fixed locking issue]
Signed-off-by: Richard Weinberger <richard@nod.at>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
If the flash's quad mode is enabled, it'll remain in the quad mode when
it's removed. If we drive the flash next time in Standard/Dual SPI mode,
the QE bit is not cleared and the function of flash's WP# and RESET#/HOLD#
have been switched to IO2 and IO3 and are not restored.
Disable the Quad mode in spi_nor_restore(), then the flash's QE bit will
be cleared when removed. This will make sure the flash always enter the
Standard/Dual SPI mode when loaded.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-3-git-send-email-yangyicong@hisilicon.com
Previous we didn't provide a way to disable the flash's quad mode.
Which means we cannot do some cleanup works when to remove or
poweroff the flash, like what set 4-byte address mode does in
spi_nor_restore().
Add the capability to disable the flash quad mode, by introducing
an enable flag in the flash parameters quad_enable() hooks and
related functions.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-2-git-send-email-yangyicong@hisilicon.com
The s70fl01gs is a dual die stack of two s25fl512s die with dedicated chip
select pins to each. Tested with the device and confirmed that is working
as two s25fl512s devices. The current device ID in the flash_info table
matches with s70fs01gs which does not work with current MTD (s70fs01gs
does not support RDSR(05h) which is critical for erase/write).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200626051650.495-1-Takahiro.Kuwano@cypress.com
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing and let flashes set it in
their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-12-p.yadav@ti.com
This MIPS driver does not support COMPILE_TEST yet and failed to build
under my radar.
Replace 'mtd' chich is not defined in the scope of xway_nand_remove()
by nand_to_mtd(chip). The mistake has been added in the long series
dropping nand_release().
Tested with a 7.3.0 MIPS GCC toolchain built with Buildroot.
Fixes: 9fdd78f7bc ("mtd: rawnand: xway: Stop using nand_release()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200626065511.16424-1-miquel.raynal@bootlin.com
FMC2 EBI support has been added. Common resources (registers base
address and clock) can now be shared between the 2 drivers using
"st,stm32mp1-fmc2-nfc" compatible string. It means that the
common resources should now be found in the parent device when EBI
node is available.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591975362-22009-7-git-send-email-christophe.kerello@st.com
A MDMA issue has been solved on Kernel 5.7. The effect of this fix is
that the MDMA driver is now deferred and the FMC2 NFC driver is also
deferred. All is working fine but there is a FMC2 log in the console:
stm32_fmc2_nfc 58002000.nand-controller: failed to request tx DMA
channel: -517
This patch removes the display of this log in the console in case of
this error is -EPROBE_DEFER.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591975362-22009-2-git-send-email-christophe.kerello@st.com
The ARRAY_SIZE() is the number of elements but we want to use sizeof()
here for the number of bytes. Fortunately, they are the same thing
because it's an array of u8 so this has no effect on runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200624132640.GC9972@mwanda
This chip is (nearly) identical to the Winbond w25q64 which is
already supported by Linux. Compared to the w25q64, the 'jvm'
has a different JEDEC ID.
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
[tudor.ambarus@microchip.com: Order entry alphabetically, update
subject, update Sven's email address]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200629195306.1030-1-TheSven73@gmail.com
The MX25R1635F is the smaller sibling of the MX25R3235F that is
already supported. It's only half the size (16Mb).
It was tested on the Kontron Electronics i.MX8MM SoM (N8010)
using raw read and write from and to the mtd device and
the 'flash_erase' command.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[tudor.ambarus@microchip.com: update subject]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200702140523.6811-1-frieder.schrempf@kontron.de
The header file linux/uio.h includes crypto/hash.h which pulls in
most of the Crypto API. Since linux/uio.h is used throughout the
kernel this means that every tiny bit of change to the Crypto API
causes the entire kernel to get rebuilt.
This patch fixes this by moving it into lib/iov_iter.c instead
where it is actually used.
This patch also fixes the ifdef to use CRYPTO_HASH instead of just
CRYPTO which does not guarantee the existence of ahash.
Unfortunately a number of drivers were relying on linux/uio.h to
provide access to linux/slab.h. This patch adds inclusions of
linux/slab.h as detected by build failures.
Also skbuff.h was relying on this to provide a declaration for
ahash_request. This patch adds a forward declaration instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Intel Tiger Lake-H has the same SPI serial flash controller as Cannon
Lake. Add Tiger Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200624192103.78770-1-mika.westerberg@linux.intel.com
Intel Emmitsburg has the same SPI serial flash controller as Lewisburg.
Add Emmitsburg PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200615155748.920-1-mika.westerberg@linux.intel.com
Instead of trying to parse CFE version string, which is customized by some
vendors, let's just check that "CFE1" was passed on argument 3.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200615091740.2958303-1-noltari@gmail.com
Implement ECC correctable and uncorrectable error handling for EDU
reads. If ECC correctable bitflips are encountered on EDU transfer,
read page again using PIO. This is needed due to a NAND controller
limitation where corrected data is not transferred to the DMA buffer
on ECC error. This applies to ECC correctable errors that are reported
by the controller hardware based on set number of bitflips threshold in
the controller threshold register, bitflips below the threshold are
corrected silently and are not reported by the controller hardware.
Fixes: a5d53ad26a ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200612212902.21347-3-kdasu.kdev@gmail.com
When flash-dma is absent do not default to using flash-edu.
Make sure flash-edu is enabled before setting EDU transfer
function.
Fixes: a5d53ad26a ("mtd: rawnand: brcmnand: Add support for flash-edu for dma transfers")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200612212902.21347-2-kdasu.kdev@gmail.com
BAM is DMA controller on QCOM ipq platforms, BAM mode on NAND driver
is set by writing BAM_MODE_EN bit on NAND_CTRL register.
NAND_CTRL is an operational register and in BAM mode operational
registers are read only.
So, before enabling BAM mode by writing the NAND_CTRL register, check
if BAM mode was already enabled by the bootloader, and enable BAM mode
only if it is not enabled already.
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591948696-16015-3-git-send-email-sivaprak@codeaurora.org
SFLASHC_BURST_CFG is only available on older ipq NAND platforms, this
register has been removed when the NAND controller got implemented in
the qpic controller.
Avoid writing this register on devices which are based on qpic NAND
controller.
Fixes: dce84760b0 ("mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller")
Cc: stable@vger.kernel.org
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1591948696-16015-2-git-send-email-sivaprak@codeaurora.org
Explicitly inherit from nand_controller instead of relying on the
nand_chip.legacy.dummy_controller field.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200603134922.1352340-8-boris.brezillon@collabora.com
The integer-based GPIO ids are now deprecated in favor of the GPIO desc
API. The PPC platforms have already been converted to GPIOLIB, so let's
use gpio descs in the NAND driver too.
While at it, we use devm_gpiod_get_index_optional() so we can get rid
of the manual gpio desc release done in the init error path and in the
remove function.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200603134922.1352340-7-boris.brezillon@collabora.com
Replace the of_address_to_resource() + devm_ioremap() calls by
platform_get_resource() + devm_ioremap_resource() ones which allows us
to get rid of one error message since devm_ioremap_resource() already
takes care of that.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200603134922.1352340-6-boris.brezillon@collabora.com
The mtd var in fun_wait_rnb() is now unused, let's get rid of it and
fix the warning resulting from this unused var.
Fixes: 50a487e771 ("mtd: rawnand: Pass a nand_chip object to chip->dev_ready()")
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200603134922.1352340-2-boris.brezillon@collabora.com
Instead of manipulating the statically allocated structure and copy
timings around, allocate one at identification time and save it in the
nand_chip structure once it has been initialized.
All NAND chips using the same interface configuration during reset and
startup, we define a helper to retrieve a single reset interface
configuration object, shared across all NAND chips.
We use a second pointer to always have a reference on the currently
applied interface configuration, which may either point to the "best
interface configuration" or to the "default reset interface
configuration".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200529111322.7184-29-miquel.raynal@bootlin.com
Hauke Mehrtens