Devices capable of offloading the kernel's datapath and perform
functions such as bridging and routing must also be able to send (trap)
specific packets to the kernel (i.e., the CPU) for processing.
For example, a device acting as a multicast-aware bridge must be able to
trap IGMP membership reports to the kernel for processing by the bridge
module.
In most cases, the underlying device is capable of handling packet rates
that are several orders of magnitude higher compared to those that can
be handled by the CPU.
Therefore, in order to prevent the underlying device from overwhelming
the CPU, devices usually include packet trap policers that are able to
police the trapped packets to rates that can be handled by the CPU.
This patch allows capable device drivers to register their supported
packet trap policers with devlink. User space can then tune the
parameters of these policer (currently, rate and burst size) and read
from the device the number of packets that were dropped by the policer,
if supported.
Subsequent patches in the series will allow device drivers to create
default binding between these policers and packet trap groups and allow
user space to change the binding.
v2:
* Add 'strict_start_type' in devlink policy
* Have device drivers provide max/min rate/burst size for each policer.
Use them to check validity of user provided parameters
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.
Remove this flag from all drivers that called
devlink_health_reporter_create.
All existing health reporters set auto recovery to true if they have a
recover method.
Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition and documentation for the new generic info
"fw.mgmt.api". This macro specifies the version of the software
interfaces between driver and firmware.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for the DEVLINK_CMD_REGION_NEW command for creating
snapshots. This new command parallels the existing
DEVLINK_CMD_REGION_DEL.
In order for DEVLINK_CMD_REGION_NEW to work for a region, the new
".snapshot" operation must be implemented in the region's ops structure.
The desired snapshot id must be provided. This helps avoid confusion on
the purpose of DEVLINK_CMD_REGION_NEW, and keeps the API simpler.
The requested id will be inserted into the xarray tracking the number of
snapshots using each id. If this id is already used by another snapshot
on any region, an error will be returned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each snapshot created for a devlink region must have an id. These ids
are supposed to be unique per "event" that caused the snapshot to be
created. Drivers call devlink_region_snapshot_id_get to obtain a new id
to use for a new event trigger. The id values are tracked per devlink,
so that the same id number can be used if a triggering event creates
multiple snapshots on different regions.
There is no mechanism for snapshot ids to ever be reused. Introduce an
xarray to store the count of how many snapshots are using a given id,
replacing the snapshot_id field previously used for picking the next id.
The devlink_region_snapshot_id_get() function will use xa_alloc to
insert an initial value of 1 value at an available slot between 0 and
U32_MAX.
The new __devlink_snapshot_id_increment() and
__devlink_snapshot_id_decrement() functions will be used to track how
many snapshots currently use an id.
Drivers must now call devlink_snapshot_id_put() in order to release
their reference of the snapshot id after adding region snapshots.
By tracking the total number of snapshots using a given id, it is
possible for the decrement() function to erase the id from the xarray
when it is not in use.
With this method, a snapshot id can become reused again once all
snapshots that referred to it have been deleted via
DEVLINK_CMD_REGION_DEL, and the driver has finished adding snapshots.
This work also paves the way to introduce a mechanism for userspace to
request a snapshot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink_snapshot_id_get() function returns a snapshot id. The
snapshot id is a u32, so there is no way to indicate an error code.
A future change is going to possibly add additional cases where this
function could fail. Refactor the function to return the snapshot id in
an argument, so that it can return zero or an error value.
This ensures that snapshot ids cannot be confused with error values, and
aids in the future refactor of snapshot id allocation management.
Because there is no current way to release previously used snapshot ids,
add a simple check ensuring that an error is reported in case the
snapshot_id would over flow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not makes sense that two snapshots for a given region would use
different destructors. Simplify snapshot creation by adding
a .destructor op for regions.
This operation will replace the data_destructor for the snapshot
creation, and makes snapshot creation easier.
Noticed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the devlink region code in preparation for adding new operations
on regions.
Create a devlink_region_ops structure, and move the name pointer from
within the devlink_region structure into the ops structure (similar to
the devlink_health_reporter_ops).
This prepares the regions to enable support of additional operations in
the future such as requesting snapshots, or accessing the region
directly without a snapshot.
In order to re-use the constant strings in the mlx4 driver their
declaration must be changed to 'const char * const' to ensure the
compiler realizes that both the data and the pointer cannot change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.
Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, packet trap groups are implicitly registered by drivers upon
packet trap registration. When the traps are registered, each is
associated with a group and the group is created by devlink, if it does
not exist already.
This makes it difficult for drivers to pass additional attributes for
the groups.
Therefore, as a preparation for future patches that require passing
additional group attributes, add an API to explicitly register /
unregister these groups.
Next patches will convert existing drivers to use this API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nfp driver uses ``fw.bundle_id`` to represent a unique identifier of the
entire firmware bundle.
A future change is going to introduce a similar notion in the ice
driver, so promote ``fw.bundle_id`` into a generic version now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add cookie argument to devlink_trap_report() allowing driver to pass in
the user cookie. Pass on the cookie down to drop monitor code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow driver to indicate cookie metadata for registered traps.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps that can report packets that were dropped during ACL
processing.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new API for start/end binary array brackets [] to force array
around binary data as required from JSON. With this restriction, re-open
API to set binary fmsg data.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add definition and documentation for the new generic info "fw.roce".
v2: Remove board.nvm_cfg since fw.psid is similar.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet trap that can report NVE packets that the device decided to
drop because their overlay source MAC is multicast.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps that can report packets that were dropped during tunnel
decapsulation.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet trap that can report packets that reached the router, but are
non-routable. For example, IGMP queries can be flooded by the device in
layer 2 and reach the router. Such packets should not be routed and
instead dropped.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function to obtain a unique snapshot id was mistakenly typo'd as
devlink_region_shapshot_id_get. Fix this typo by renaming the function
and all of its users.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine the documentation for devlink into a subfolder, and provide an
index.rst file that can be used to generally describe devlink.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "fw.psid" devlink info version is documented in devlink-info.rst,
and used by one driver. However, there is no associated macro for this
firmware version like there is for others. Add one now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that a reporter recovery completion do not finish
successfully when recovery is triggered via
devlink_health_reporter_recover as recovery could be processed in
different context. In such scenario an error is returned by driver when
recover hook is invoked and successful recovery completion is
intimated later.
Expose devlink recover done API to update recovery stats.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) New generic devlink param "enable_roce", for downstream devlink
reload support
2) Do vport ACL configuration on per vport basis when
enabling/disabling a vport. This enables to have vports enabled/disabled
outside of eswitch config for future
3) Split the code for legacy vs offloads mode and make it clear
4) Tide up vport locking and workqueue usage
5) Fix metadata enablement for ECPF
6) Make explicit use of VF property to publish IB_DEVICE_VIRTUAL_FUNCTION
7) E-Switch and flow steering core low level support and refactoring for
netfilter flowtables offload
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Devlink supports pair output of name and value. When the value is
binary, it must be presented in an array. If the length of the binary
value exceeds fmsg limitation, break the value into chunks internally.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New device parameter to enable/disable handling of RoCE traffic in the
device.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add layer 3 generic packet exception traps that can report trapped
packets and documentation of the traps.
Unlike drop traps, these exception traps also need to inject the packet
to the kernel's receive path. For example, a packet that was trapped due
to unreachable neighbour need to be injected into the kernel so that it
will trigger an ARP request or a neighbour solicitation message.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet traps that can report packets that were dropped during layer
3 forwarding.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During health reporter operations, driver might want to fill-up
the extack message, so propagate extack down to the health reporter ops.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For newly allocated devlink instance allow drivers to set net struct
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All devlink instances are created in init_net and stay there for a
lifetime. Allow user to be able to move devlink instances into
namespaces during devlink reload operation. That ensures proper
re-instantiation of driver objects, including netdevices.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to get net struct for devlink instance.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the fact that devlink reload failed is stored in drivers.
Move this flag into devlink core. Also, expose it to the user.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly implement failure indication during reload,
split the reload op into two ops, one for down phase and one for
up phase.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the 'reset_dev_on_drv_probe' devlink parameter, controlling the
device reset policy on driver probe.
This parameter is useful in conjunction with the existing
'fw_load_policy' parameter.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tag set is still rather small and needs a couple
more tags to help with ASIC identification and to have a
more generic FW version.
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink port index attribute is returned to users as u32 through
netlink response.
Change index data type from 'unsigned' to 'unsigned int' to avoid
below checkpatch.pl warning.
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
81: FILE: include/net/devlink.h:81:
+ unsigned index;
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial documentation of the devlink-trap mechanism, explaining the
background, motivation and the semantics of the interface.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic packet traps and groups that can report dropped packets as
well as exceptions such as TTL error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the basic packet trap infrastructure that allows device drivers to
register their supported packet traps and trap groups with devlink.
Each driver is expected to provide basic information about each
supported trap, such as name and ID, but also the supported metadata
types that will accompany each packet trapped via the trap. The
currently supported metadata type is just the input port, but more will
be added in the future. For example, output port and traffic class.
Trap groups allow users to set the action of all member traps. In
addition, users can retrieve per-group statistics in case per-trap
statistics are too narrow. In the future, the trap group object can be
extended with more attributes, such as policer settings which will limit
the amount of traffic generated by member traps towards the CPU.
Beside registering their packet traps with devlink, drivers are also
expected to report trapped packets to devlink along with relevant
metadata. devlink will maintain packets and bytes statistics for each
packet trap and will potentially report the trapped packet with its
metadata to user space via drop monitor netlink channel.
The interface towards the drivers is simple and allows devlink to set
the action of the trap. Currently, only two actions are supported:
'trap' and 'drop'. When set to 'trap', the device is expected to provide
the sole copy of the packet to the driver which will pass it to devlink.
When set to 'drop', the device is expected to drop the packet and not
send a copy to the driver. In the future, more actions can be added,
such as 'mirror'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the snapshot has to be the same as the size of the region,
therefore no need to pass it again during snapshot creation. Remove the
arg and use region->size instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an eswitch, PCI VF may have port which is normally represented using
a representor netdevice.
To have better visibility of eswitch port, its association with VF,
and its representor netdevice, introduce a PCI VF port flavour.
When devlink port flavour is PCI VF, fill up PCI VF attributes of
the port.
Extend port name creation using PCI PF and VF number scheme on best
effort basis, so that vendor drivers can skip defining their own scheme.
$ devlink port show
pci/0000:05:00.0/0: type eth netdev eth0 flavour pcipf pfnum 0
pci/0000:05:00.0/1: type eth netdev eth1 flavour pcivf pfnum 0 vfnum 0
pci/0000:05:00.0/2: type eth netdev eth2 flavour pcivf pfnum 0 vfnum 1
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an eswitch, PCI PF may have port which is normally represented
using a representor netdevice.
To have better visibility of eswitch port, its association with
PF and a representor netdevice, introduce a PCI PF port
flavour and port attriute.
When devlink port flavour is PCI PF, fill up PCI PF attributes of the
port.
Extend port name creation using PCI PF number on best effort basis.
So that vendor drivers can skip defining their own scheme.
$ devlink port show
pci/0000:05:00.0/0: type eth netdev eth0 flavour pcipf pfnum 0
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support additional devlink port flavours and to support few common
and few different port attributes, move physical port attributes to a
different structure.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Misc updates from mlx5-next branch:
1) E-Switch vport metadata support for source vport matching
2) Convert mkey_table to XArray
3) Shared IRQs and to use single IRQ for all async EQs
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Devlink has UAPI declaration for encap mode, so there is no
need to be loose on the data get/set by drivers.
Update call sites to use enum devlink_eswitch_encap_mode
instead of plain u8.
Suggested-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a function to be called from drivers during flash. It sends
notification to userspace about flash update progress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel