BSM or Backup Switch Mode is a common feature on RTCs, allowing to select
how the RTC will decide when to switch from its primary power supply to the
backup power supply. It is necessary to be able to set it from userspace as
there are uses cases where it has to be done dynamically.
Supported values are:
RTC_BSM_DISABLED: disabled
RTC_BSM_DIRECT: switching will happen as soon as Vbackup > Vdd
RTC_BSM_LEVEL: switching will happen around a threshold, usually with an
hysteresis
RTC_BSM_STANDBY: switching will not happen until Vdd > Vbackup, this is
useful to ensure the RTC doesn't draw any power until the device is first
powered on.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018151933.76865-6-alexandre.belloni@bootlin.com
I got a null-ptr-deref report when doing fault injection test:
general protection fault, probably for non-canonical address 0xdffffc0000000022: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000110-0x0000000000000117]
RIP: 0010:device_del+0x132/0xdc0
Call Trace:
cdev_device_del+0x1a/0x80
devm_rtc_unregister_device+0x37/0x80
release_nodes+0xc3/0x3b0
If cdev_device_add() fails, 'dev->p' is not set, it causes
null-ptr-deref when calling cdev_device_del(). Registering
character device is optional, we don't return error code
here, so introduce a new flag 'RTC_NO_CDEV' to indicate
if it has character device, cdev_device_del() is called
when this bit is not set.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211011132114.3663509-1-yangyingliang@huawei.com
Introduce a bitfield to allow the drivers to announce the available
features for an RTC.
The main use case would be to better handle alarms, that could be present
or not or have a minute resolution or may need a correct week day to be set.
Use the newly introduced RTC_FEATURE_ALARM bit to then test whether alarms
are available instead of relying on the presence of ops->set_alarm.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210110231752.1418816-2-alexandre.belloni@bootlin.com
Subsystem:
- Remove nvram ABI. There was no complaints about the deprecation for the last
3 years.
- Improve RTC device allocation and registration
- Now available for ARCH=um
Drivers:
- at91rm9200: correction and sam9x60 support
- ds1307: improve ACPI support
- mxc: now DT only
- pcf2127: watchdog support now needs the reset-source property
- pcf8523: set range
- rx6110: i2c support
-----BEGIN PGP SIGNATURE-----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=n8V2
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- Remove nvram ABI. There was no complaints about the deprecation for
the last 3 years.
- Improve RTC device allocation and registration
- Now available for ARCH=um
Drivers:
- at91rm9200: correction and sam9x60 support
- ds1307: improve ACPI support
- mxc: now DT only
- pcf2127: watchdog support now needs the reset-source property
- pcf8523: set range
- rx6110: i2c support"
* tag 'rtc-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (43 commits)
rtc: pcf2127: only use watchdog when explicitly available
dt-bindings: rtc: add reset-source property
rtc: fix RTC removal
rtc: s3c: Remove dead code related to periodic tick handling
rtc: s3c: Disable all enable (RTC, tick) bits in the probe
rtc: ep93xx: Fix NULL pointer dereference in ep93xx_rtc_read_time
rtc: test: remove debug message
rtc: mxc{,_v2}: enable COMPILE_TEST
rtc: enable RTC framework on ARCH=um
rtc: pcf8523: use BIT
rtc: pcf8523: set range
rtc: pcf8523: switch to devm_rtc_allocate_device
rtc: destroy mutex when releasing the device
rtc: shrink devm_rtc_allocate_device()
rtc: rework rtc_register_device() resource management
rtc: nvmem: emit an error message when nvmem registration fails
rtc: add devm_ prefix to rtc_nvmem_register()
rtc: nvmem: remove nvram ABI
Documentation: list RTC devres helpers in devres.rst
rtc: omap: use devm_pinctrl_register()
...
The current RTC set_offset_nsec value is not really intuitive to
understand.
tsched twrite(t2.tv_sec - 1) t2 (seconds increment)
The offset is calculated from twrite based on the assumption that t2 -
twrite == 1s. That means for the MC146818 RTC the offset needs to be
negative so that the write happens 500ms before t2.
It's easier to understand when the whole calculation is based on t2. That
avoids negative offsets and the meaning is obvious:
t2 - twrite: The time defined by the chip when seconds increment
after the write.
twrite - tsched: The time for the transport to the point where the chip
is updated.
==> set_offset_nsec = t2 - tsched
ttransport = twrite - tsched
tRTCinc = t2 - twrite
==> set_offset_nsec = ttransport + tRTCinc
tRTCinc is a chip property and can be obtained from the data sheet.
ttransport depends on how the RTC is connected. It is close to 0 for
directly accessible RTCs. For RTCs behind a slow bus, e.g. i2c, it's the
time required to send the update over the bus. This can be estimated or
even calibrated, but that's a different problem.
Adjust the implementation and update comments accordingly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201206220542.263204937@linutronix.de
rtc_set_ntp_time() is not really RTC functionality as the code is just a
user of RTC. Move it into the NTP code which allows further cleanups.
Requested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201206220542.166871172@linutronix.de
rtc_register_device() is a managed interface but it doesn't use devres
by itself - instead it marks an rtc_device as "registered" and the devres
callback for devm_rtc_allocate_device() takes care of resource release.
This doesn't correspond with the design behind devres where managed
structures should not be aware of being managed. The correct solution
here is to register a separate devres callback for unregistering the
device.
While at it: rename rtc_register_device() to devm_rtc_register_device()
and add it to the list of managed interfaces in devres.rst. This way we
can avoid any potential confusion of driver developers who may expect
there to exist a corresponding unregister function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201109163409.24301-8-brgl@bgdev.pl
rtc_nvmem_register() is a managed interface. It doesn't require any
release function to be called at driver detach. To avoid confusing
driver authors, let's rename it to devm_rtc_nvmem_register() and add it
to the list of managed interfaces in Documentation/.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201109163409.24301-6-brgl@bgdev.pl
The nvram sysfs attributes have been deprecated at least since v4.13, more
than 3 years ago and nobody ever complained about the deprecation warning.
Remove the sysfs attributes now.
[Bartosz: remove the declaration of rtc_nvmem_unregister()]
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201109163409.24301-5-brgl@bgdev.pl
Commit ea369ea6d8 ("rtc: remove .open() and .release()") removes
open/release callback from struct rtc_class_ops.
Also commit 80d4bb515b ("RTC: Cleanup rtc_class_ops->irq_set_state")
and commit 696160fec1 ("RTC: Cleanup rtc_class_ops->irq_set_freq()")
removes irq callbacks.
So, just remove related comments so that readers will not be confused.
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200710080003.7986-1-misono.tomohiro@jp.fujitsu.com
There are no users of set_mms and set_mmss64 as they have all been
converted to set_time and are handling the tm to time conversion on their
own.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DA9062 and DA9063 have a year register that can go up to 0x3F.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The SH RTC is a BCD RTC with some version having 4 digits for the year.
The range for the RTCs with only 2 digits for the year was unfortunately
shifted to handle 1999 to 2098.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since commit 416f0e8056 ("RTC: sa1100: Update the sa1100 RTC driver."),
the last user of .read_callback is gone. It has been 8 years and now new
user appeared. Simply remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
All the remaining users of rtc_timers are passing the rtc_device as private
data. Enforce that and rename private_data to rtc.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using devm_nvmem_register allows to avoid tracking the nvmem pointer in the
rtc_device structure.
This ultimately allows to register multiple nvmem devices from an RTC
driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
devm_rtc_device_unregister is not used by any driver and should not be used
by any new driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move rtc_add_group and rtc_add_groups definition to rtc.h that is available
for all RTC drivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ensure the non managed version of the un/registration functions is not used
anymore. No driver is using it anymore and they should not be necessary.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Avoid reporting an error when RTC_NVMEM is not selected.
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
From our investigation for all RTC drivers, 1 driver will be expired before
year 2017, 7 drivers will be expired before year 2038, 23 drivers will be
expired before year 2069, 72 drivers will be expired before 2100 and 104
drivers will be expired before 2106. Especially for these early expired
drivers, we need to expand the RTC range to make the RTC can still work
after the expired year.
So we can expand the RTC range by adding one offset to the time when reading
from hardware, and subtracting it when writing back. For example, if you have
an RTC that can do 100 years, and currently is configured to be based in
Jan 1 1970, so it can represents times from 1970 to 2069. Then if you change
the start year from 1970 to 2000, which means it can represents times from
2000 to 2099. By adding or subtracting the offset produced by moving the wrap
point, all times between 1970 and 1999 from RTC hardware could get interpreted
as times from 2070 to 2099, but the interpretation of dates between 2000 and
2069 would not change.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a way for drivers to inform the core of the supported date/time range.
The core can then check whether the date/time or alarm is in the range
before calling ->set_time, ->set_mmss or ->set_alarm. It returns -ERANGE
when the time is out of range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since commit 34ce71a96d ("ALSA: timer: remove legacy rtctimer"), the
rtc_register/rtc_control/rtc_unregister API is unused. As it is highly
unlikely to be needed again, remove it.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Because nvmem_config is only used and copied at nvmem registration, remove
it from struct rtc_device.
All the rtc drivers using nvmem are now calling rtc_nvmem_register
directly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Export rtc_nvmem_register() so it can be called from drivers instead of
only the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The last usage was removed in 5c82a6ae0 when rtc_device.name
was removed
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ntp is currently hardwired to try and call the rtc set when wall clock
tv_nsec is 0.5 seconds. This historical behaviour works well with certain
PC RTCs, but is not universal to all rtc hardware.
Change how this works by introducing the driver specific concept of
set_offset_nsec, the delay between current wall clock time and the target
time to set (with a 0 tv_nsecs).
For x86-style CMOS set_offset_nsec should be -0.5 s which causes the last
second to be written 0.5 s after it has started.
For compat with the old rtc_set_ntp_time, the value is defaulted to
+ 0.5 s, which causes the next second to be written 0.5s before it starts,
as things were before this patch.
Testing shows many non-x86 RTCs would like set_offset_nsec ~= 0,
so ultimately each RTC driver should set the set_offset_nsec according
to its needs, and non x86 architectures should stop using
update_persistent_clock64 in order to access this feature.
Future patches will revise the drivers as needed.
Since CMOS and RTC now have very different handling they are split
into two dedicated code paths, sharing the support code, and ifdefs
are replaced with IS_ENABLED.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
There are no driver left using .open and .release. There is no good use
case for them as there is nothing the character device interface does that
should not be done in the sysfs interface or in-kernel interface.
Remove those callbacks now to avoid future confusion.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_time_to_tm and rtc_tm_to_time are not deprecated and make perfect sense
for RTCs that are simple 32bit counters.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Many RTCs have an on board non volatile storage. It can be battery backed
RAM or an EEPROM. Use the nvmem subsystem to export it to both userspace
and in-kernel consumers.
This stays compatible with the previous (non documented) ABI that was using
/sys/class/rtc/rtcx/device/nvram to export that memory. But will warn about
the deprecation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Introduce rtc_register_device() to register an already allocated and
initialized struct rtc_device. It automatically sets up the owner and the
two steps allocation/registration will allow to remove race conditions in
the IRQ handling of some driver. It also allows to properly extend the core
without adding more arguments to rtc_device_register().
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc->name is only used in messages were it is superfluous. Remove it
completely from the structure.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
A number of rtc devices, such as the NXP pcf2123 include a facility
to adjust the clock in order to compensate for temperature or a
crystal, capacitor, etc, that results in the rtc clock not running
at exactly 32.768 kHz.
Data sheets I have seen refer to this as a clock offset, and measure it
in parts per million, however they often reference ppm to 2 digits of
precision, which makes integer ppm less than ideal.
We use parts per billion, which more than covers the precision needed
and works nicely within 32 bits
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now rtc_set_mmss() has no users, just remove it.
We still have rtc_set_time() doing similar things.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There're many sites need comparing the two rtc_time variants for many
rtc drivers, especially in the instances of rtc_class_ops::set_alarm().
So add this common helper function to make things easy.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc_timer_cancel() always returns 0 and cannot fail (calls only
other void-returning functions).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Alexandre Belloni