Remove excess semicolon after closing parenthesis.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
mv88e6xxx: Allow config of ATU hash algorithm
v2:
Pass a pointer for where the hash should be stored, return a plain
errno, or 0.
Document the parameter.
v3:
Document type of parameter, and valid range
Add break statements to default clause of switch
Directly use ctx->val.vu8
v4:
Consistently use devlink, not a mix of devlink and dl.
Fix allocation of devlink priv
Remove upper case from parameter name
Make mask 16 bit wide.
v5:
Back to using the parameter name ATU_hash
v6:
Rebase net-next/master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the marvell switches have bits controlling the hash algorithm
the ATU uses for MAC addresses. In some industrial settings, where all
the devices are from the same manufacture, and hence use the same OUI,
the default hashing algorithm is not optimal. Allow the other
algorithms to be selected via devlink.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add plumbing to allow DSA drivers to register parameters with devlink.
To keep with the abstraction, the DSA drivers pass the ds structure to
these helpers, and the DSA core then translates that to the devlink
structure associated to the device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
One place in the driver was left where the open-coded functionality
hasn't been replaced with helper rtl_hw_aspm_clkreq_enable yet.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: b53: Add support for MDB
This patch series adds support for programming multicast database
entries on b53 and bcm_sf2. This is extracted from a previously
submitted series that added managed mode support, but these patches are
usable in isolation. The larger series still needs to be reworked.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Leverage the recently add b53_mdb_{add,del,prepare} functions since they
work as-is for bcm_sf2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting IGMP snooping with or without the use of
a bridge, add support within b53_common.c to program the ARL entries for
multicast operations. The key difference is that a multicast ARL entry
is comprised of a bitmask of enabled ports, instead of a port number.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce says:
====================
mvpp2 improvements in rx path
Refactor some code in the RX path to allow prefetching some data from the
packet header. The first patch is only a refactor, the second one
reduces the data synced, while the third one adds the prefetch.
The packet rate improvement with the second patch is very small (1606 => 1620 kpps),
while the prefetch bumps it up by 14%: 1620 => 1853 kpps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving traffic, eth_type_trans() is high up on the perf top list,
because it's the first function which access the packet data.
Move the DMA unmap a bit higher, and put a prefetch just after it, so we
have more time to load the data into the cache.
The packet rate increase is about 14% with a tc drop test: 1620 => 1853 kpps
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the RX path we always sync against the maximum frame size for that pool.
Do the DMA sync and the unmap separately, so we can only sync by the
size of the received frame.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misspellings of "endpoints", "configuration", and "device's".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misspellings of "disconnect", "disconnecting", "connections", and
"disconnected".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix various misspellings of "configuration" and "configure".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 0394a63acf ("net: dsa: enable and disable all ports")
the dsa core disables all unused ports of a switch. In this case
disabling ports with numbers higher than QCA8K_NUM_PORTS causes that
some switch registers are overwritten with incorrect content.
To fix this, initialize the dsa_switch->num_ports with correct number
of ports.
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ds->dev is dereferenced on the assignments of pdata and
np before ds->dev is null checked, hence there is a potential null
pointer dereference on ds->dev. Fix this by assigning pdata and
np after the ds->dev null pointer sanity check.
Addresses-Coverity: ("Dereference before null check")
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-10-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 52 non-merge commits during the last 11 day(s) which contain
a total of 65 files changed, 2604 insertions(+), 1100 deletions(-).
The main changes are:
1) Revolutionize BPF tracing by using in-kernel BTF to type check BPF
assembly code. The work here teaches BPF verifier to recognize
kfree_skb()'s first argument as 'struct sk_buff *' in tracepoints
such that verifier allows direct use of bpf_skb_event_output() helper
used in tc BPF et al (w/o probing memory access) that dumps skb data
into perf ring buffer. Also add direct loads to probe memory in order
to speed up/replace bpf_probe_read() calls, from Alexei Starovoitov.
2) Big batch of changes to improve libbpf and BPF kselftests. Besides
others: generalization of libbpf's CO-RE relocation support to now
also include field existence relocations, revamp the BPF kselftest
Makefile to add test runner concept allowing to exercise various
ways to build BPF programs, and teach bpf_object__open() and friends
to automatically derive BPF program type/expected attach type from
section names to ease their use, from Andrii Nakryiko.
3) Fix deadlock in stackmap's build-id lookup on rq_lock(), from Song Liu.
4) Allow to read BTF as raw data from bpftool. Most notable use case
is to dump /sys/kernel/btf/vmlinux through this, from Jiri Olsa.
5) Use bpf_redirect_map() helper in libbpf's AF_XDP helper prog which
manages to improve "rx_drop" performance by ~4%., from Björn Töpel.
6) Fix to restore the flow dissector after reattach BPF test and also
fix error handling in bpf_helper_defs.h generation, from Jakub Sitnicki.
7) Improve verifier's BTF ctx access for use outside of raw_tp, from
Martin KaFai Lau.
8) Improve documentation for AF_XDP with new sections and to reflect
latest features, from Magnus Karlsson.
9) Add back 'version' section parsing to libbpf for old kernels, from
John Fastabend.
10) Fix strncat bounds error in libbpf's libbpf_prog_type_by_name(),
from KP Singh.
11) Turn on -mattr=+alu32 in LLVM by default for BPF kselftests in order
to improve insn coverage for built BPF progs, from Yonghong Song.
12) Misc minor cleanups and fixes, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated config with required kernel options for conntrac TC action,
so that tdc can run the tests.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
more specifically:
* Updates for ipset:
1) Coding style fix for ipset comment extension, from Jeremy Sowden.
2) De-inline many functions in ipset, from Jeremy Sowden.
3) Move ipset function definition from header to source file.
4) Move ip_set_put_flags() to source, export it as a symbol, remove
inline.
5) Move range_to_mask() to the source file where this is used.
6) Move ip_set_get_ip_port() to the source file where this is used.
* IPVS selftests and netns improvements:
7) Two patches to speedup ipvs netns dismantle, from Haishuang Yan.
8) Three patches to add selftest script for ipvs, also from
Haishuang Yan.
* Conntrack updates and new nf_hook_slow_list() function:
9) Document ct ecache extension, from Florian Westphal.
10) Skip ct extensions from ctnetlink dump, from Florian.
11) Free ct extension immediately, from Florian.
12) Skip access to ecache extension from nf_ct_deliver_cached_events()
this is not correct as reported by Syzbot.
13) Add and use nf_hook_slow_list(), from Florian.
* Flowtable infrastructure updates:
14) Move priority to nf_flowtable definition.
15) Dynamic allocation of per-device hooks in flowtables.
16) Allow to include netdevice only once in flowtable definitions.
17) Rise maximum number of devices per flowtable.
* Netfilter hardware offload infrastructure updates:
18) Add nft_flow_block_chain() helper function.
19) Pass callback list to nft_setup_cb_call().
20) Add nft_flow_cls_offload_setup() helper function.
21) Remove rules for the unregistered device via netdevice event.
22) Support for multiple devices in a basechain definition at the
ingress hook.
22) Add nft_chain_offload_cmd() helper function.
23) Add nft_flow_block_offload_init() helper function.
24) Rewind in case of failing to bind multiple devices to hook.
25) Typo in IPv6 tproxy module description, from Norman Rasmussen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
net: aquantia: ptp followup fixes
Here are two sparse warnings, third patch is a fix for
scaled_ppm_to_ppb missing. Eventually I reworked this
to exclude ptp module from build. Please consider it instead
of this patch: https://patchwork.ozlabs.org/patch/1184171/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We do disable aq_ptp module build using inline
stubs when CONFIG_PTP_1588_CLOCK is not declared.
This reduces module size and removes unnecessary code.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes to remove sparse warnings:
sparse: sparse: cast to restricted __be64
Fixes: 04a1839950 ("net: aquantia: implement data PTP datapath")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
found by sparse, simply useless local initialization with zero.
Fixes: 94ad94558b ("net: aquantia: add PTP rings infrastructure")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nft_flow_block_chain() needs to unbind in case of error when performing
the multi-device binding.
Fixes: d54725cd11 ("netfilter: nf_tables: support for multiple devices per netdev hook")
Reported-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds the nft_flow_block_offload_init() helper function to
initialize the flow_block_offload object.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
syzbot reported following splat:
BUG: KASAN: use-after-free in __nf_ct_ext_exist
include/net/netfilter/nf_conntrack_extend.h:53 [inline]
BUG: KASAN: use-after-free in nf_ct_deliver_cached_events+0x5c3/0x6d0
net/netfilter/nf_conntrack_ecache.c:205
nf_conntrack_confirm include/net/netfilter/nf_conntrack_core.h:65 [inline]
nf_confirm+0x3d8/0x4d0 net/netfilter/nf_conntrack_proto.c:154
[..]
While there is no reproducer yet, the syzbot report contains one
interesting bit of information:
Freed by task 27585:
[..]
kfree+0x10a/0x2c0 mm/slab.c:3757
nf_ct_ext_destroy+0x2ab/0x2e0 net/netfilter/nf_conntrack_extend.c:38
nf_conntrack_free+0x8f/0xe0 net/netfilter/nf_conntrack_core.c:1418
destroy_conntrack+0x1a2/0x270 net/netfilter/nf_conntrack_core.c:626
nf_conntrack_put include/linux/netfilter/nf_conntrack_common.h:31 [inline]
nf_ct_resolve_clash net/netfilter/nf_conntrack_core.c:915 [inline]
^^^^^^^^^^^^^^^^^^^
__nf_conntrack_confirm+0x21ca/0x2830 net/netfilter/nf_conntrack_core.c:1038
nf_conntrack_confirm include/net/netfilter/nf_conntrack_core.h:63 [inline]
nf_confirm+0x3e7/0x4d0 net/netfilter/nf_conntrack_proto.c:154
This is whats happening:
1. a conntrack entry is about to be confirmed (added to hash table).
2. a clash with existing entry is detected.
3. nf_ct_resolve_clash() puts skb->nfct (the "losing" entry).
4. this entry now has a refcount of 0 and is freed to SLAB_TYPESAFE_BY_RCU
kmem cache.
skb->nfct has been replaced by the one found in the hash.
Problem is that nf_conntrack_confirm() uses the old ct:
static inline int nf_conntrack_confirm(struct sk_buff *skb)
{
struct nf_conn *ct = (struct nf_conn *)skb_nfct(skb);
int ret = NF_ACCEPT;
if (ct) {
if (!nf_ct_is_confirmed(ct))
ret = __nf_conntrack_confirm(skb);
if (likely(ret == NF_ACCEPT))
nf_ct_deliver_cached_events(ct); /* This ct has refcount 0! */
}
return ret;
}
As of "netfilter: conntrack: free extension area immediately", we can't
access conntrack extensions in this case.
To fix this, make sure we check the dying bit presence before attempting
to get the eache extension.
Reported-by: syzbot+c7aabc9fe93e7f3637ba@syzkaller.appspotmail.com
Fixes: 2ad9d7747c ("netfilter: conntrack: free extension area immediately")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Shannon Nelson says:
====================
ionic updates
These are a few of the driver updates we've been working on internally.
These clean up a few mismatched struct comments, add checking for dead
firmware, fix an initialization bug, and change the Rx buffer management.
These are based on net-next v5.4-rc3-709-g985fd98ab5cc.
v2: clear napi->skb in the error case in ionic_rx_frags()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Even out Rx performance across MTU sizes by changing from full
skb allocations to page-based frag allocations. The device
supports a form of scatter-gather in the Rx path, so we can
set up a number of pages for each descriptor, all of which are
easier to alloc and pass around than the standard kzalloc'd
buffer. An skb is wrapped around the pages while processing
the received packets, and pages are recycled as needed, or
left alone if they weren't used in the Rx.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a watchdog to periodically monitor the NIC heartbeat.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of our firmware has a heartbeat feature that the driver
can watch for to see if the FW is still alive and likely to
answer a dev_cmd or AdminQ request.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the initial interrupt coalesce usec-to-hw setting
to actually be usec-to-hw.
Fixes: 780eded34c ("ionic: report users coalesce request")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up struct names in the ionic_if.h comments
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have only one user of the error path, so we can inline it.
In addition the call to rtl8169_make_unusable_by_asic() can be removed
because rtl8169_alloc_rx_data() didn't call rtl8169_mark_to_asic() yet
for the respective index if returning NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aligns the fix_features callback with the vendor driver and
also disables IPv6 HW checksumming and TSO if jumbo packets are used
on RTL8101/RTL8168/RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-10-23
Here's the main bluetooth-next pull request for the 5.5 kernel:
- Multiple fixes to hci_qca driver
- Fix for HCI_USER_CHANNEL initialization
- btwlink: drop superseded driver
- Add support for Intel FW download error recovery
- Various other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCPI_OPT_SYN_DATA bit as part of tcpi_options currently reports whether
or not data-in-SYN was ack'd on both the client and server side. We'd like
to gather more information on the client-side in the failure case in order
to indicate the reason for the failure. This can be useful for not only
debugging TFO, but also for creating TFO socket policies. For example, if
a middle box removes the TFO option or drops a data-in-SYN, we can
can detect this case, and turn off TFO for these connections saving the
extra retransmits.
The newly added tcpi_fastopen_client_fail status is 2 bits and has the
following 4 states:
1) TFO_STATUS_UNSPEC
Catch-all state which includes when TFO is disabled via black hole
detection, which is indicated via LINUX_MIB_TCPFASTOPENBLACKHOLE.
2) TFO_COOKIE_UNAVAILABLE
If TFO_CLIENT_NO_COOKIE mode is off, this state indicates that no cookie
is available in the cache.
3) TFO_DATA_NOT_ACKED
Data was sent with SYN, we received a SYN/ACK but it did not cover the data
portion. Cookie is not accepted by server because the cookie may be invalid
or the server may be overloaded.
4) TFO_SYN_RETRANSMITTED
Data was sent with SYN, we received a SYN/ACK which did not cover the data
after at least 1 additional SYN was sent (without data). It may be the case
that a middle-box is dropping data-in-SYN packets. Thus, it would be more
efficient to not use TFO on this connection to avoid extra retransmits
during connection establishment.
These new fields do not cover all the cases where TFO may fail, but other
failures, such as SYN/ACK + data being dropped, will result in the
connection not becoming established. And a connection blackhole after
session establishment shows up as a stalled connection.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko says:
====================
net: phy: dp83867: enable robust auto-mdix
Patch 1 - improves link detection when dp83867 PHY is configured in manual mode
by enabling CFG3[9] Robust Auto-MDIX option.
Patch 2 - is minor optimization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move DT parsing code to probe dp83867_probe() as it's one time operation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link detection timeouts can be observed (or link might not be detected
at all) when dp83867 PHY is configured in manual mode (speed/duplex).
CFG3[9] Robust Auto-MDIX option allows to significantly improve link detection
in case dp83867 is configured in manual mode and reduce link detection
time.
As per DM: "If link partners are configured to operational modes that are
not supported by normal Auto MDI/MDIX mode (like Auto-Neg versus Force
100Base-TX or Force 100Base-TX versus Force 100Base-TX), this Robust Auto
MDI/MDIX mode allows MDI/MDIX resolution and prevents deadlock."
Hence, enable this option by default as there are no known reasons
not to do so.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is networking hardware that isn't based on Ethernet for layers 1 and 2.
For example CAN.
CAN is a multi-master serial bus standard for connecting Electronic Control
Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes
of payload. Frame corruption is detected by a CRC. However frame loss due to
corruption is possible, but a quite unusual phenomenon.
While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of
legacy protocols on top of CAN, which are not build with flow control or high
CAN frame drop rates in mind.
When using fq_codel, as soon as the queue reaches a certain delay based length,
skbs from the head of the queue are silently dropped. Silently meaning that the
user space using a send() or similar syscall doesn't get an error. However
TCP's flow control algorithm will detect dropped packages and adjust the
bandwidth accordingly.
When using fq_codel and sending raw frames over CAN, which is the common use
case, the user space thinks the package has been sent without problems, because
send() returned without an error. pfifo_fast will drop skbs, if the queue
length exceeds the maximum. But with this scheduler the skbs at the tail are
dropped, an error (-ENOBUFS) is propagated to user space. So that the user
space can slow down the package generation.
On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH
during compile time, or set default during runtime with sysctl
net.core.default_qdisc (see [1]), we get a bad user experience. In my test case
with pfifo_fast, I can transfer thousands of million CAN frames without a frame
drop. On the other hand with fq_codel there is more then one lost CAN frame per
thousand frames.
As pointed out fq_codel is not suited for CAN hardware, so this patch changes
attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices.
During transition of a netdev from down to up state the default queuing
discipline is attached by attach_default_qdiscs() with the help of
attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to
attach the pfifo_fast (pfifo_fast_ops) if the network device type is
"ARPHRD_CAN".
[1] https://github.com/systemd/systemd/issues/9194
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the pointer rtl_fw->fw would be used before checking in
rtl8152_apply_firmware() that causes the following kernel oops.
Unable to handle kernel NULL pointer dereference at virtual address 00000002
pgd = (ptrval)
[00000002] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 131 Comm: kworker/0:2 Not tainted
5.4.0-rc1-00539-g9370f2d05a2a #6788
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events_long rtl_hw_phy_work_func_t
PC is at rtl8152_apply_firmware+0x14/0x464
LR is at r8153_hw_phy_cfg+0x24/0x17c
pc : [<c064f4e4>] lr : [<c064fa18>] psr: a0000013
sp : e75c9e60 ip : 60000013 fp : c11b7614
r10: e883b91c r9 : 00000000 r8 : fffffffe
r7 : e883b640 r6 : fffffffe r5 : fffffffe r4 : e883b640
r3 : 736cfe7c r2 : 736cfe7c r1 : 000052f8 r0 : e883b640
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 6640006a DAC: 00000051
Process kworker/0:2 (pid: 131, stack limit = 0x(ptrval))
Stack: (0xe75c9e60 to 0xe75ca000)
...
[<c064f4e4>] (rtl8152_apply_firmware) from [<c064fa18>]
(r8153_hw_phy_cfg+0x24/0x17c)
[<c064fa18>] (r8153_hw_phy_cfg) from [<c064e784>]
(rtl_hw_phy_work_func_t+0x220/0x3e4)
[<c064e784>] (rtl_hw_phy_work_func_t) from [<c0148a74>]
(process_one_work+0x22c/0x7c8)
[<c0148a74>] (process_one_work) from [<c0149054>] (worker_thread+0x44/0x520)
[<c0149054>] (worker_thread) from [<c0150548>] (kthread+0x130/0x164)
[<c0150548>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xe75c9fb0 to 0xe75c9ff8)
...
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching to alu32 by default, no_alu32/ subdirectory wasn't added
to .gitignore. Fix it.
Fixes: e13a2fe642 ("tools/bpf: Turn on llvm alu32 attribute by default")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191025045503.3043427-1-andriin@fb.com
The bpftool interface stays the same, but now it's possible
to run it over BTF raw data, like:
$ bpftool btf dump file /sys/kernel/btf/vmlinux
[1] INT '(anon)' size=4 bits_offset=0 nr_bits=32 encoding=(none)
[2] INT 'long unsigned int' size=8 bits_offset=0 nr_bits=64 encoding=(none)
[3] CONST '(anon)' type_id=2
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Link: https://lore.kernel.org/bpf/20191024133025.10691-1-jolsa@kernel.org
This patch makes a few changes to btf_ctx_access() to prepare
it for non raw_tp use case where the attach_btf_id is not
necessary a BTF_KIND_TYPEDEF.
It moves the "btf_trace_" prefix check and typedef-follow logic to a new
function "check_attach_btf_id()" which is called only once during
bpf_check(). btf_ctx_access() only operates on a BTF_KIND_FUNC_PROTO
type now. That should also be more efficient since it is done only
one instead of every-time check_ctx_access() is called.
"check_attach_btf_id()" needs to find the func_proto type from
the attach_btf_id. It needs to store the result into the
newly added prog->aux->attach_func_proto. func_proto
btf type has no name, so a proper name should be stored into
"attach_func_name" also.
v2:
- Move the "btf_trace_" check to an earlier verifier phase (Alexei)
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191025001811.1718491-1-kafai@fb.com
Madalin Bucur says:
====================
DPAA Ethernet changes
v3: add newline at the end of error messages
v2: resending with From: field matching signed-off-by
Here's a series of changes for the DPAA Ethernet, addressing minor
or unapparent issues in the codebase, adding probe ordering based on
a recently added DPAA QMan API, removing some redundant code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Newline was missing at the end of the error message.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing