Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Use the possessive "its" instead of the contraction "it's"
where appropriate.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The drivers/leds/rgb subdirectory is relatively fresh, so we move this
new PWM multi-color driver into it.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
By allowing to group multiple monochrome PWM LEDs into multicolor LEDs,
all involved LEDs can be controlled in-sync. This enables using effects
using triggers, etc.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The Light Pulse Generator (LPG) is a PWM-block found in a wide range of
PMICs from Qualcomm. These PMICs typically comes with 1-8 LPG instances,
with their output being routed to various other components, such as
current sinks or GPIOs.
Each LPG instance can operate on fixed parameters or based on a shared
lookup-table, altering the duty cycle over time. This provides the means
for hardware assisted transitions of LED brightness.
A typical use case for the fixed parameter mode is to drive a PWM
backlight control signal, the driver therefor allows each LPG instance
to be exposed to the kernel either through the LED framework or the PWM
framework.
A typical use case for the LED configuration is to drive RGB LEDs in
smartphones etc, for which the driver supports multiple channels to be
ganged up to a MULTICOLOR LED. In this configuration the pattern
generators will be synchronized, to allow for multi-color patterns.
The idea of modelling this as a LED driver ontop of a PWM driver was
considered, but setting the properties related to patterns does not fit
in the PWM API. Similarly the idea of just duplicating the lower bits in
a PWM and LED driver separately was considered, but this would not allow
the PWM channels and LEDs to be configured on a per-board basis. The
driver implements the more complex LED interface, and provides a PWM
interface on the side of that, in the same driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
[On the Sony Xperia Nile Discovery, SDM630]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
I had to rebase at last moment to fix wrong author of one
commit. Sorry about that.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYd8hdwAKCRAw5/Bqldv6
8m3sAKC20ddEFW04Mk45Tw72qSyud6vhwQCaAnQy6dcd+zV6LOxosgLZdtXkvx0=
=CU+X
-----END PGP SIGNATURE-----
Merge tag 'leds-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Nothing major is happening here"
* tag 'leds-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lp55xx: initialise output direction from dts
ARM: dts: omap3-n900: Fix lp5523 for multi color
leds: ktd2692: Drop calling dev_of_node() in ktd2692_parse_dt
leds: lgm-sso: Get rid of duplicate of_node assignment
leds: tca6507: Get rid of duplicate of_node assignment
leds: leds-fsg: Drop FSG3 LED driver
leds: lp50xx: remove unused variable
dt-bindings: leds: Replace moonlight with indicator in mt6360 example
leds: led-core: Update fwnode with device_set_node
leds: tca6507: use swap() to make code cleaner
leds: Add mt6360 driver
dt-bindings: leds: Add bindings for MT6360 LED
The board file using this driver has been deleted and the
FSG3 LEDs can be modeled using a system controller and some
register bit LEDs in the device tree so this driver is no
longer needed.
Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Krzysztof Hałasa <khalasa@piap.pl>
Cc: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This driver adds initial support for several devices from Siemens. It is
based on a platform driver introduced in an earlier commit.
One of the supported machines has GPIO connected LEDs, here we poke GPIO
memory directly because pinctrl does not come up.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20211213120502.20661-3-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The 9-channel one is called LP5009, not LP509.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Cc: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
We created a subdirectory for LED drivers that depend on
CONFIG_LEDS_CLASS_FLASH, and this driver does so let's
move it there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the driver to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Regmap APIs should be selected, otherwise link can fail
ERROR: modpost: "__devm_regmap_init_i2c" [drivers/leds/leds-lm3532.ko] undefined!
Fixes: bc1b8492c7 ("leds: lm3532: Introduce the lm3532 LED driver")
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Remove unnecessary Kconfig symbol LEDS_BLINK
Improve Kconfig help text to make it more useful.
Signed-off-by: Rahul Tanwar <rtanwar@maxlinear.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
changing CLASS_FLASH to return success to make it easier to work with
V4L2 stuff disabled, and we are getting rid of enum that should have
been plain integer long time ago. I'm slightly nervous about potential
warnings, but it needed to be fixed at some point.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAmA2ETMACgkQMOfwapXb+vI0MQCgrQMf02DV2hvyJm2Oj4Vx6WKd
5VYAn0J/8OKSj4BHiW82s4H4tuP8e1TD
=GYC4
-----END PGP SIGNATURE-----
Merge tag 'leds-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Besides the usual fixes and new drivers, we are changing CLASS_FLASH
to return success to make it easier to work with V4L2 stuff disabled,
and we are getting rid of enum that should have been plain integer
long time ago. I'm slightly nervous about potential warnings, but it
needed to be fixed at some point"
* tag 'leds-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lp50xx: Get rid of redundant explicit casting
leds: lp50xx: Update headers block to reflect reality
leds: lp50xx: Get rid of redundant check in lp50xx_enable_disable()
leds: lp50xx: Reduce level of dereferences
leds: lp50xx: Switch to new style i2c-driver probe function
leds: lp50xx: Don't spam logs when probe is deferred
leds: apu: extend support for PC Engines APU1 with newer firmware
leds: flash: Fix multicolor no-ops registration by return 0
leds: flash: Add flash registration with undefined CONFIG_LEDS_CLASS_FLASH
leds: lgm: Add LED controller driver for LGM SoC
dt-bindings: leds: Add bindings for Intel LGM SoC
leds: led-core: Get rid of enum led_brightness
leds: gpio: Set max brightness to 1
leds: lm3533: Switch to using the new API kobj_to_dev()
leds: ss4200: simplify the return expression of register_nasgpio_led()
leds: Use DEVICE_ATTR_{RW, RO, WO} macros
Parallel to serial conversion, which is also called SSO controller,
can drive external shift register for LED outputs, reset or
general purpose outputs.
This driver enables LED support for Serial Shift Output Controller (SSO).
Signed-off-by: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This adds a driver for the Richtek RT8515 dual channel
torch/flash white LED driver.
This LED driver is found in some mobile phones from
Samsung such as the GT-S7710 and GT-I8190.
A V4L interface is added.
We do not have a proper datasheet for the RT8515 but
it turns out that RT9387A has a public datasheet and
is essentially the same chip. We designed the driver
in accordance with this datasheet. The day someone
needs to drive a RT9387A this driver can probably
easily be augmented to handle that chip too.
Sakari Ailus, Pavel Machek and Andy Shevchenko helped
significantly in getting this driver right.
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: newbytee@protonmail.com
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: linux-media@vger.kernel.org
Cc: phone-devel@vger.kernel.org
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acer Iconia Tab A500 is an Android tablet device which has two LEDs
embedded into the Power Button. Orange LED indicates "battery charging"
status and white LED indicates "wake-up/charge-done" status. The new LED
driver provides control over both LEDs to userspace.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This driver can be compiled on other platforms with small change if
COMPILE_TEST=y.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
These drivers can be compiled without modification when COMPILE_TEST=y:
cobalt-qube, cobalt-raq, netxbig, ns2 and s3c24xx
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Introduce the LP5036/30/24/18/12/9 RGB LED driver.
The difference in these parts are the number of
LED outputs where the:
LP5036 can control 36 LEDs
LP5030 can control 30 LEDs
LP5024 can control 24 LEDs
LP5018 can control 18 LEDs
LP5012 can control 12 LEDs
LP5009 can control 9 LEDs
The device has the ability to group LED outputs into control banks
so that multiple LED banks can be controlled with the same mixing and
brightness. Or the LED outputs can also be controlled independently.
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
With these kernel configs:
CONFIG_LEDS_CLASS=m
# CONFIG_LEDS_CLASS_MULTICOLOR is not set
CONFIG_LEDS_LP55XX_COMMON=y
CONFIG_LEDS_LP5521=m
CONFIG_LEDS_LP5562=m
leds-lp55xx-common.c has a build error because it is builtin and
calls an interface that is built as a loadable module (due to
LEDS_CLASS=m). By making LEDS_LP55XX_COMMON depend on LEDS_CLASS,
this config combination cannot happen, thus preventing the build error.
ld: drivers/leds/leds-lp55xx-common.o: in function `lp55xx_register_leds':
leds-lp55xx-common.c:(.text+0xc5f): undefined reference to `devm_led_classdev_register_ext'
Fixes: 33b3a561f4 ("leds: support new LP8501 device - another LP55xx common")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Milo Kim <milo.kim@ti.com>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Pavel Machek <pavel@ucw.cz>
leds-lp55xx-common.c:(.text+0x9d): undefined reference to `i2c_smbus_read_byte_data'
leds-lp55xx-common.c:(.text+0x8fc): undefined reference to `i2c_smbus_write_byte_data'
These errors happened when I2C=m and LEDS_LP55XX_COMMON=y, so
prevent that from being possible.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: linux-leds@vger.kernel.org
Cc: Milo Kim <milo.kim@ti.com>
Cc: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This adds basic support for LEDs on the front side of CZ.NIC's Turris
Omnia router.
There are 12 RGB LEDs. The controller supports HW triggering mode for
the LEDs, but this driver does not support it yet, and sets all the LEDs
defined in device-tree into SW mode upon probe.
This driver uses the multicolor LED framework.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add multicolor framework support for the lp55xx family.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Introduce a multicolor class that groups colored LEDs
within a LED node.
The multicolor class groups monochrome LEDs and allows controlling two
aspects of the final combined color: hue and lightness. The former is
controlled via the intensity file and the latter is controlled
via brightness file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[squashed leds: multicolor: Fix camel case in documentation in]
This commit adds support for AWINIC AW2013 3-channel LED driver.
The chip supports 3 PWM channels and is controlled with I2C.
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add a driver for the SGMICRO SGM3140 Buck/Boost Charge Pump LED driver.
This device is controlled by two GPIO pins, one for enabling and the
second one for switching between torch and flash mode.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This adds support for controlling the LEDs attached to the Embedded
Controller on a Dell Wyse 3020 "Ariel" board.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This patch implemenets a driver to support the front panel LEDs of
SGI Octane (IP30) workstations.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This driver adds support for the LED operational mode of the
tps6105x MFD device.
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Update the Kconfig to be consistent in the case of using
"LED" in the Kconfig. LED is an acronym and should be
capitalized.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This patch adds a LED class driver for the LEDs found on
the Crane Merchandising System EL15203000 LEDs board
(aka RED LEDs board).
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Since commit ebc278f157 ("ARM: mvebu: remove static LED setup for
netxbig boards"), no one in upstream passes in the platform data to
this driver.
Squash leds-kirkwood-netxbig.h into the driver, and remove the legacy
board-file support.
Link: https://lkml.org/lkml/2019/7/20/83
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This driver only supports gpio-attached LEDs on apu1/2/3 boards,
but neither gpio's themselves, nor other gpio-attached devices
(eg. front button).
For apu2+ a newer, more complete driver exists, based on a generic
driver for the AMD SOCs gpio-controller, supporting LEDs as well
other devices. Therefore these boards don't need legacy support
from this driver anymore.
Both drivers claim the same device, so only one driver may exist
in a system, putting distros in the position to decide between
either apu2+ keys or apu1 led support.
Therefore drop the apu2+ led support from the old driver, solve
the conflict and reduce unnecessary code.
Signed-off-by: Enrico Weigelt <info@metux.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXRozKAAKCRBiEGxRG/Sl
25okAP9I0Rmscpqjb/+GEeXH4EmL3moGzc9o/BzHRqfeO4wqYAEA+8f7L20xHe8g
tvEGfP7mN/oBmcAfqgH5K9F4eJsBRAw=
=NkCn
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- Add a new LED common module for ti-lmu driver family
- Modify MFD ti-lmu bindings
- add ti,brightness-resolution
- add the ramp up/down property
- Add regulator support for LM36274 driver to lm363x-regulator.c
- New LED class drivers with DT bindings:
- leds-spi-byte
- leds-lm36274
- leds-lm3697 (move the support from MFD to LED subsystem)
- Simplify getting the I2C adapter of a client:
- leds-tca6507
- leds-pca955x
- Convert LED documentation to ReST
* tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
dt: leds-lm36274.txt: fix a broken reference to ti-lmu.txt
docs: leds: convert to ReST
leds: leds-tca6507: simplify getting the adapter of a client
leds: leds-pca955x: simplify getting the adapter of a client
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: max77650: Remove set but not used variable 'parent'
leds: avoid flush_work in atomic context
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
leds: spi-byte: add single byte SPI LED driver
dt-bindings: leds: Add binding for spi-byte LED.
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property
with DT bindings:
- leds-lm3697
- leds-lm36274
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXQAatQAKCRBiEGxRG/Sl
2/2KAQDHnHR0rIITh3hH49YutOCzGK4oaut8sXfy+8PTEdKBlQEApQP1O1RJTTws
/KDS8qpNdwOQOW/KYiYDX5R8GcOeZwg=
=we/t
-----END PGP SIGNATURE-----
Merge tag 'ti-lmu-led-drivers' into for-next
Merge immutable branch between LEDs, MFD and REGULATOR due to
TI LMU LED support rework and introduction of two new drivers
with DT bindings.
* tag 'ti-lmu-led-drivers':
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property
Introduce the LM36274 LED driver. This driver uses the ti-lmu
MFD driver to probe this LED driver. The driver configures only the
LED registers and enables the outputs according to the config file.
The driver utilizes the TI LMU (Lighting Management Unit) LED common
framework to set the brightness bits.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Introduce the lm3697 LED driver for backlighting and display.
Datasheet location:
http://www.ti.com/lit/ds/symlink/lm3697.pdf
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Create a TI LMU common framework for TI LMU devices that share
common features.
Currently the runtime ramp and brightness setting have
been identified as common features with common register settings.
This work is derived from Milo Kims TI LMU MFD code.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This driver adds support for simple SPI based LED controller which use
only one byte for setting the brightness.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Document (kerneldoc) core mfd_add_devices() API
- New Drivers
- Add support for Altera SOCFPGA System Manager
- Add support for Maxim MAX77650/77651 PMIC
- Add support for Maxim MAX77663 PMIC
- Add support for ST Multi-Function eXpander (STMFX)
- New Device Support
- Add support for LEDs to Intel Cherry Trail Whiskey Cove PMIC
- Add support for RTC to SAMSUNG Electronics S2MPA01 PMIC
- Add support for SAM9X60 to Atmel HLCDC (High-end LCD Controller)
- Add support for USB X-Powers AXP 8xx PMICs
- Add support for Integrated Sensor Hub (ISH) to ChromeOS EC
- Add support for USB PD Logger to ChromeOS EC
- Add support for AXP223 to X-Powers AXP series PMICs
- Add support for Power Supply to X-Powers AXP 803 PMICs
- Add support for Comet Lake to Intel Low Power Subsystem
- Add support for Fingerprint MCU to ChromeOS EC
- Add support for Touchpad MCU to ChromeOS EC
- Move TI LM3532 support to LED
- New Functionality
- Add/extend DT support; max77650, max77620
- Add support for power-off; max77620
- Add support for clocking; syscon
- Add support for host sleep event; cros_ec
- Fix-ups
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
- Bug Fixes
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio
-----BEGIN PGP SIGNATURE-----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=dTSD
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
-----BEGIN PGP SIGNATURE-----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=55X1
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-arm-leds-5.2', 'ib-mfd-gpio-input-leds-power-5.2', 'ib-mfd-pinctrl-5.2-2' and 'ib-mfd-regulator-5.2', tag 'ib-mfd-arm-net-5.2' into ibs-for-mfd-merged
Immutable branch between MFD, ARM and Net due for the 5.2 merge window
Andy Shevchenko