Since the op_mode defines the queue mapping, let it do it
completely through the API functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently when mac80211 asks to change the interface
type, we will accept it for both the BSS and PAN
contexts. This is not terribly complicated today,
but with the addition of the P2P Device abstraction
the PAN context handling will get more complex, so
restrict mac_change_interface to the BSS context.
Also fix a small locking issue and use is_active
instead of the vif pointer to check if the other
context is activated, guarding exclusive interface
types on the BSS context (IBSS) against the PAN
context being used for something else.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the first interface is active, then scanning
on it or the second interface can take a little
longer than 7s (I observed around 8s.) Bump the
timeout to 15s to avoid aborting a scan that is
still running, just taking more time.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My previous commit to shorten the radio reset time
caused issues as the firmware checks the active
dwell time against the quiet time, asserting that
the dwell is >= quiet time. This isn't really
needed in case of passive scanning like here, but
of course we need to pass that check.
To fix this, override the quiet time to be the
same as the radio reset dwell time.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that the eeprom parsing code overrides the sku
field directly with 11n_disable parameters, there's
no longer a need to keep a copy of this field.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The effect of using a short single-channel scan
to reset the radio is that scanning a channel
that isn't in use needs to re-tune the radio.
This means that the dwell time is irrelevant,
so use a shorter time.
While at it, clean up the code for this a bit.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the device is doing an internal radio reset
scan, ROC can be rejected to the supplicant with
busy status which confuses it.
One option would be to queue the ROC and handle
it later, but since the radio reset scan is very
quick we can just wait for it to finish instead.
Also add a warning since we shouldn't run into
the case of having a scan active when requesting
a ROC in any other case since mac80211 will not
scan while ROC or ROC while scanning.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This feature needs to be disabled for all NICs.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This flow can actually happen due to a corner case in
mac80211: the station is deleted before we get a chance
to reclaim all the packets in flight in AGG queue.
The tid_data for this station is zeroed, and we lose
the match with the Tx queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CMD_SYNC is zero so the if (cmd->flags & CMD_SYNC) is never true and we
never check the assertion.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the driver_data area in ieee80211_tx_info which
resides in the CB overrides the info->control field.
Add a comment to prevent mistakes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change its name to better reflect this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This macro gets the bufsize in bytes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwl-test flows were based on the cfg80211 testmode APIs.
To remove this coupling, the op mode (during the initialization
of the iwl_test object) is responsible to set the callbacks that
should be used by iwl-test to allocate skbs for events and replies
and to send events and replies.
The current op modes implement these callbacks based on the cfg80211
testmode APIs.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Create an object that will enacpsulate the testmode functionality
that is common to all op modes.
* Copy definitions from dvm/dev.h
* Copy the testmode logic from dvm/testmode.c
* Link iwl-test object into the iwlwifi module
* Modify DVM to use iwl-test object
Reviewed-by: Amit Beka <amit.beka@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to declare the opmode ops
as extern since they're now dynamically
registered.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the RF config is done for all devices,
there's no need to keep a separate function
that is called for all devices, move it into
the general NIC config function.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should also configure the PHY version in the
CSR_HW_IF_CONFIG_REG register for 1000 series
devices, not just for the other devices.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7c5ba4a830 ("iwlwifi: move queue
watchdog into transport") introduced the named constant
'IWL_WATCHHDOG_DISABLED'. Rename it to 'IWL_WATCHDOG_DISABLED'.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The EEPROM reading/parsing code is all mixed in
the driver today, and the EEPROM is parsed only
when we access data from it. This is problematic
because the NVM needs to be parsed and that is
independent of reading it. Also, the NVM format
for new devices will be different and probably
require a new parser.
Therefore refactor the reading and parsing and
create two independent components. Reading the
EEPROM requires direct hardware accesses and
therefore access to the transport, but parsing
is independent and can be done on an NVM blob.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was missing. Fix the mask of the REV_TYPE on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes noticed this was completely messed up.
We got confused between masks and bit position.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Different transports will have different needs: New tranports
need headroom for their own use before the Tx cmd. So allocate
the Tx cmd pool in the transport and give it a unique name
based on dev_name.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to enable / disable Tx queues in HW
dynamically. So this function is no longer related to AGG
only. It can do the job for any queue, even AC ones. Change
the name to better reflect its role.
Also use the new function to configure the AC / CMD queues
in tx_start.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to enable / disable Tx queues in HW
dynamically. So this function is no longer related to AGG
only. It can do the job for any queue, even AC ones. Change
the name to better reflect its role.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to dynamically fill the HT40
band bitmap as it's a device parameter, just
put it into the HT configuration.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to copy the same code for all
devices since none of the 5000 series devices
(that don't have the RX SISO override) don't
set the rx_with_siso_diversity variable.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we're working on another mode/driver
inside iwlwifi, move the current one into a
subdirectory to more cleanly separate the
code. While at it, rename all the files.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach