There's an issue with how sense requests are handled in IDE. If ide-cd
encounters an error, it queues a sense request. With how IDE request
handling is done, this is the next request we need to handle. But it's
impossible to guarantee this, as another request could come in between
the sense being queued, and ->queue_rq() being run and handling it. If
that request ALSO fails, then we attempt to doubly queue the single
sense request we have.
Since we only support one active request at the time, defer request
processing when a sense request is queued.
Fixes: 600335205b "ide: convert to blk-mq"
Reported-by: He Zhe <zhe.he@windriver.com>
Tested-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can't use RQF_DONTPREP to see if we should clear ->special,
as someone could have set that while inserting the request. Make
sure we clear it in our ->initialize_rq_fn() helper instead.
Fixes: 22ce0a7ccf ("ide: don't use req->special")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ide-disk and ide-cd tested as working just fine, ide-tape and
ide-floppy haven't. But the latter don't require changes, so they
should work without issue.
Add helper function to insert a request from a work queue, since we
cannot invoke the blk-mq request insertion from IRQ context.
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have ways to deal with drainage in the block layer, and libata has
been using it for ages. We also want to get rid of PCI_DMA_BUS_IS_PHYS
now, so just reduce the PCI transfer size for ide - anyone who cares for
performance on PCI controllers should have switched to libata long ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
ide_toggle_bounce did select various strange block bounce limits, including
not bouncing at all as soon as an iommu is present in the system. Given
that the dma_map routines now handle any required bounce buffering except
for ISA DMA, and the ide code already must handle either ISA DMA or highmem
at least for iommu equipped systems we can get rid of the block layer
bounce limit setting entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename get_disk() to get_disk_and_module() to make sure what the
function does. It's not a great name but at least it is now clear that
put_disk() is not it's counterpart.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Since scsi_req_init() works on a struct scsi_request, change the
argument type into struct scsi_request *.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of explicitly calling scsi_req_init() after blk_get_request(),
call that function from inside blk_get_request(). Add an
.initialize_rq_fn() callback function to the block drivers that need
it. Merge the IDE .init_rq_fn() function into .initialize_rq_fn()
because it is too small to keep it as a separate function. Keep the
scsi_req_init() call in ide_prep_sense() because it follows a
blk_rq_init() call.
References: commit 82ed4db499 ("block: split scsi_request out of struct request")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
From the context where a SCSI command is submitted it is not always
possible to figure out whether or not the queue the command is
submitted to has struct scsi_request as the first member of its
private data. Hence introduce the flag QUEUE_FLAG_SCSI_PASSTHROUGH.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Don Brace <don.brace@microsemi.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On m68k, host->get_lock is used to both lock and register the interrupt
that the IDE host shares with other device drivers. Registering the
IDE interrupt handler in ide-probe.c results in duplicating the
interrupt registered (once via host->get lock, and also via init_irq()),
and may result in IDE accepting interrupts even when another driver has
locked the interrupt hardware. This opens the whole locking scheme up
to races.
host->get_lock is set on m68k only, so other drivers' behaviour is not
changed.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-ide@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling dev_set_name with a single paramter causes it to be handled as a
format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents,
including wrappers like device_create*() and bdi_register().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We must ensure that ide_proc_port_register_devices() occurs on an
interface before ide_proc_register_driver() executes for that
interfaces drives.
Therefore defer the registry of the driver device objects backed by
ide_bus_type until after ide_proc_port_register_devices() has run
and thus all of the drive->proc procfs directory pointers have been
setup.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a20b2a44ec.
As requested by David Fries. This makes CDROMs which are slave drives
on a ribbon without a master disappear and causes other similar kinds
of badness.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6: (49 commits)
drivers/ide: Fix continuation line formats
ide: fixed section mismatch warning in cmd640.c
ide: ide_timing_compute() fixup
ide: make ide_get_best_pio_mode() static
via82cxxx: use ->pio_mode value to determine pair device speed
tx493xide: use ->pio_mode value to determine pair device speed
siimage: use ->pio_mode value to determine pair device speed
palm_bk3710: use ->pio_mode value to determine pair device speed
it821x: use ->pio_mode value to determine pair device speed
cs5536: use ->pio_mode value to determine pair device speed
cs5535: use ->pio_mode value to determine pair device speed
cmd64x: fix handling of address setup timings
amd74xx: use ->pio_mode value to determine pair device speed
alim15x3: fix handling of UDMA enable bit
alim15x3: fix handling of DMA timings
alim15x3: fix handling of command timings
alim15x3: fix handling of address setup timings
ide-timings: use ->pio_mode value to determine fastest PIO speed
ide: change ->set_dma_mode method parameters
ide: change ->set_pio_mode method parameters
...
Except for SCSI no device drivers distinguish between physical and
hardware segment limits. Consolidate the two into a single segment
limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add pio_mode field to ide_drive_t matching pio_mode field used in
struct ata_device.
The validity of the field is restricted to ->set_pio_mode method
only currently in IDE subsystem.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6029336426.
Ok, we really do need to revert this, even with Bart's sis5513.c
fix in there.
The problem is that several driver's ->set_pio_mode() method
depends upon the drive->media type being set properly. Most
of them use this to enable prefetching, which can only be done
for disk media.
But the commit being reverted here calls ->set_pio_mode() before
it's setup. Actually it considers everything disk because that
is the default media type set by ide_port_init_devices_data().
The set of drivers that depend upon the media type in their
->set_pio_method() are:
drivers/ide/alim15x3.c
drivers/ide/it8172.c
drivers/ide/it8213.c
drivers/ide/pdc202xx_old.c
drivers/ide/piix.c
drivers/ide/qd65xx.c
drivers/ide/sis5513.c
drivers/ide/slc90e66.c
And it is possible that we could fix this by guarding the prefetching
and other media dependent setting changes with a test on
IDE_PFLAG_PROBING in hwif->port_flags, that's simply too risky for
2.6.32-rcX and -stable.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 24df31acaf.
The root cause of reported system hangs was (now fixed) sis5513 bug
and not "ide: try to use PIO Mode 0 during probe if possible" change
(commit 6029336426) so the revert was
incorrect (it simply replaced one regression with the other one).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6029336426.
Based upon a report by David Fries, wherein his system hangs
on bootup with sis5513 controller, right after the CDROM
is registered by ide-cd.c and the TOC is first read.
Signed-off-by: David S. Miller <davem@davemloft.net>
* Un-static __ide_wait_stat().
* Allow ide_dev_read_id() helper to be called from the IRQ context by
adding irq_ctx flag and using mdelay()/__ide_wait_stat() when needed.
* Switch ide_driveid_update() to set irq_ctx flag.
This change is needed for the consecutive patch which fixes races in
handling of user-space SET XFER commands but for improved bisectability
and clarity it is better to do it in a separate patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ide_host_enable_irqs() helper and use it in ide_host_register()
before registering ports. Then remove no longer needed IRQ unmasking
from in init_irq().
This should fix the problem with "screaming" shared IRQ on the first
port (after request_irq() call while we have the unexpected IRQ pending
on the second port) which was uncovered by my rework of the serialized
interfaces support.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: linux-ide@vger.kernel.org
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the ack_intr() method into 'struct ide_port_ops', also renaming it to
test_irq() while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'unsigned long port_flags' field to ide_hwif_t.
* Add IDE_PFLAG_PROBING port flag and keep it set during probing.
* Fix ide_pio_need_iordy() to not enable IORDY at a probe time
(IORDY may lead to controller lock up on certain controllers
if the port is not occupied).
Loosely based on the recent libata's fix by Tejun, thanks to Alan
for the hint that IDE may also need it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
PowerMac bootup with CONFIG_IDE=y oopses in ide_pio_cycle_time():
because "ide: try to use PIO Mode 0 during probe if possible" causes
pmac_ide_set_pio_mode() to be called before drive->id has been set.
Bart points out other places which now need drive->id set earlier,
so follow his advice to allocate it in ide_port_alloc_devices()
(using kzalloc_node, without error message, as when allocating drive)
and memset it for reuse in ide_port_init_devices_data().
Fixed in passing: ide_host_alloc() was missing ide_port_free_devices()
from an error path.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Joao Ramos <joao.ramos@inov.pt>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In ide_probe_port() skip probe if ide_port_wait_ready() returns -ENODEV
and print error message instead of debug one if it returns -EBUSY.
v2:
Fix the default 'rc' value.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_check_nien_quirk_list() helper to the core code
and then use it in ide_port_tune_devices().
* Remove no longer needed ->quirkproc methods from hpt366.c
and pdc202xx_{new,old}.c.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove hw_regs_t typedef and rename struct hw_regs_s to struct ide_hw.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Pass number of ports to ide_host_{alloc,add}() and then update
all users accordingly.
v2:
- drop no longer needed NULL initializers in buddha.c, cmd640.c and gayle.c
(noticed by Sergei)
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert host drivers that still use hw_regs_t's chipset field to use
the one in struct ide_port_info instead.
* Move special handling of ide_pci chipset type from ide_hw_configure()
to ide_init_port().
* Remove chipset field from hw_regs_t.
While at it:
- remove stale comment in delkin_cb.c
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace:
- special_t typedef by IDE_SFLAG_* flags
- 'special_t special' ide_drive_t's field by 'u8 special_flags' one
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Initially set PIO Mode 0 for all host drivers that have a 'set_pio_mode'
method before the IDE core figures out the most suited PIO mode for the
attached device.
Signed-off-by: Joao Ramos <joao.ramos@inov.pt>
Cc: Sergei Shtylyov <sshtylyov@ru.montavista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_read() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and factoring out the code that
deals with the high order bytes into ide_tf_readback() to be called from the
only two functions interested, ide_complete_cmd() and ide_dump_sector().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for
the method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_load() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and moving the code that deals
with the high order bytes into the only function interested, do_rw_taskfile().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for the
method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Jens Axboe