The entries in the DMA translation tables for our IOMMU must specify
physical addresses of either the next level table or the final page
to be mapped for DMA. Currently however the code simply passes the
virtual addresses of both. On the other hand we still need to walk the
tables via their virtual addresses so we need to do a phys_to_virt()
when setting the entries and a virt_to_phys() when getting them.
Similarly when passing the I/O translation anchor to the hardware we
must also specify its physical address.
As the DMA and IOMMU APIs we are implementing already use the correct
phys_addr_t type for the address to be mapped let's also thread this
through instead of treating it as just an unsigned long.
Note: this currently doesn't fix a real bug, since virtual addresses
are indentical to physical ones.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
When supporting only the .map and .unmap callbacks of iommu_ops,
the IOMMU driver can make assumptions about the size and alignment
used for mappings based on the driver provided pgsize_bitmap. VT-d
previously used essentially PAGE_MASK for this bitmap as any power
of two mapping was acceptably filled by native page sizes.
However, with the .map_pages and .unmap_pages interface we're now
getting page-size and count arguments. If we simply combine these
as (page-size * count) and make use of the previous map/unmap
functions internally, any size and alignment assumptions are very
different.
As an example, a given vfio device assignment VM will often create
a 4MB mapping at IOVA pfn [0x3fe00 - 0x401ff]. On a system that
does not support IOMMU super pages, the unmap_pages interface will
ask to unmap 1024 4KB pages at the base IOVA. dma_pte_clear_level()
will recurse down to level 2 of the page table where the first half
of the pfn range exactly matches the entire pte level. We clear the
pte, increment the pfn by the level size, but (oops) the next pte is
on a new page, so we exit the loop an pop back up a level. When we
then update the pfn based on that higher level, we seem to assume
that the previous pfn value was at the start of the level. In this
case the level size is 256K pfns, which we add to the base pfn and
get a results of 0x7fe00, which is clearly greater than 0x401ff,
so we're done. Meanwhile we never cleared the ptes for the remainder
of the range. When the VM remaps this range, we're overwriting valid
ptes and the VT-d driver complains loudly, as reported by the user
report linked below.
The fix for this seems relatively simple, if each iteration of the
loop in dma_pte_clear_level() is assumed to clear to the end of the
level pte page, then our next pfn should be calculated from level_pfn
rather than our working pfn.
Fixes: 3f34f12597 ("iommu/vt-d: Implement map/unmap_pages() iommu_ops callback")
Reported-by: Ajay Garg <ajaygargnsit@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Link: https://lore.kernel.org/all/20211002124012.18186-1-ajaygargnsit@gmail.com/
Link: https://lore.kernel.org/r/163659074748.1617923.12716161410774184024.stgit@omen
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211126135556.397932-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
With the submission of iommu driver for RK3568 a subtle bug was
introduced: PAGE_DESC_HI_MASK1 and PAGE_DESC_HI_MASK2 have to be
the other way arround - that leads to random errors, especially when
addresses beyond 32 bit are used.
Fix it.
Fixes: c55356c534 ("iommu: rockchip: Add support for iommu v2")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Dan Johansen <strit@manjaro.org>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Link: https://lore.kernel.org/r/20211124021325.858139-1-knaerzche@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
The MSI doorbell on Apple HW can be any address in the low 4GB range.
However, the MSI write is matched by the PCIe block before hitting the
iommu. It must thus be excluded from the IOVA range that is assigned to any
PCIe device.
Link: https://lore.kernel.org/r/20210929163847.2807812-9-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Including:
- Intel IOMMU Updates fro Lu Baolu:
- Dump DMAR translation structure when DMA fault occurs
- An optimization in the page table manipulation code
- Use second level for GPA->HPA translation
- Various cleanups
- Arm SMMU Updates from Will
- Minor optimisations to SMMUv3 command creation and submission
- Numerous new compatible string for Qualcomm SMMUv2 implementations
- Fixes for the SWIOTLB based implemenation of dma-iommu code for
untrusted devices
- Add support for r8a779a0 to the Renesas IOMMU driver and DT matching
code for r8a77980
- A couple of cleanups and fixes for the Apple DART IOMMU driver
- Make use of generic report_iommu_fault() interface in the AMD IOMMU
driver
- Various smaller fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=waUR
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Intel IOMMU Updates fro Lu Baolu:
- Dump DMAR translation structure when DMA fault occurs
- An optimization in the page table manipulation code
- Use second level for GPA->HPA translation
- Various cleanups
- Arm SMMU Updates from Will
- Minor optimisations to SMMUv3 command creation and submission
- Numerous new compatible string for Qualcomm SMMUv2 implementations
- Fixes for the SWIOTLB based implemenation of dma-iommu code for
untrusted devices
- Add support for r8a779a0 to the Renesas IOMMU driver and DT matching
code for r8a77980
- A couple of cleanups and fixes for the Apple DART IOMMU driver
- Make use of generic report_iommu_fault() interface in the AMD IOMMU
driver
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (35 commits)
iommu/dma: Fix incorrect error return on iommu deferred attach
iommu/dart: Initialize DART_STREAMS_ENABLE
iommu/dma: Use kvcalloc() instead of kvzalloc()
iommu/tegra-smmu: Use devm_bitmap_zalloc when applicable
iommu/dart: Use kmemdup instead of kzalloc and memcpy
iommu/vt-d: Avoid duplicate removing in __domain_mapping()
iommu/vt-d: Convert the return type of first_pte_in_page to bool
iommu/vt-d: Clean up unused PASID updating functions
iommu/vt-d: Delete dev_has_feat callback
iommu/vt-d: Use second level for GPA->HPA translation
iommu/vt-d: Check FL and SL capability sanity in scalable mode
iommu/vt-d: Remove duplicate identity domain flag
iommu/vt-d: Dump DMAR translation structure when DMA fault occurs
iommu/vt-d: Do not falsely log intel_iommu is unsupported kernel option
iommu/arm-smmu-qcom: Request direct mapping for modem device
iommu: arm-smmu-qcom: Add compatible for QCM2290
dt-bindings: arm-smmu: Add compatible for QCM2290 SoC
iommu/arm-smmu-qcom: Add SM6350 SMMU compatible
dt-bindings: arm-smmu: Add compatible for SM6350 SoC
iommu/arm-smmu-v3: Properly handle the return value of arm_smmu_cmdq_build_cmd()
...
The end goal of the current buffer overflow detection work[0] is to gain
full compile-time and run-time coverage of all detectable buffer overflows
seen via array indexing or memcpy(), memmove(), and memset(). The str*()
family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this series
contains the foundational elements of several related buffer overflow
detection improvements by providing new common helpers and FORTIFY_SOURCE
changes needed to gain the introspection required for compiler visibility
into array sizes. Also included are a handful of already Acked instances
using the helpers (or related clean-ups), with many more waiting at the
ready to be taken via subsystem-specific trees[2]. The new helpers are:
- struct_group() for gaining struct member range introspection.
- memset_after() and memset_startat() for clearing to the end of structures.
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in structs.
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage under
GCC, and to prepare to fix the currently broken Clang support. Finishing
this work is part of the larger series[0], but depends on all the false
positives and buffer overflow bug fixes to have landed already and those
that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a compile-time
and run-time tests are added for FORTIFY_SOURCE and the mem*()-family
functions respectively. The compile time tests have found a legitimate
(though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage that
result in no known object code differences.
After this series (and the changes that have now landed via netdev
and usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds. However, due corner cases in
GCC[3] and Clang[4], I have not included the last two patches that turn
on these options, as I don't want to introduce any known warnings to
the build. Hopefully these can be solved soon.
[0] https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE
[2] https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/
[3] https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/
[4] https://bugs.llvm.org/show_bug.cgi?id=51682
[5] https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/
[6] https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/
-----BEGIN PGP SIGNATURE-----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=9xbT
-----END PGP SIGNATURE-----
Merge tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"The end goal of the current buffer overflow detection work[0] is to
gain full compile-time and run-time coverage of all detectable buffer
overflows seen via array indexing or memcpy(), memmove(), and
memset(). The str*() family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this
series contains the foundational elements of several related buffer
overflow detection improvements by providing new common helpers and
FORTIFY_SOURCE changes needed to gain the introspection required for
compiler visibility into array sizes. Also included are a handful of
already Acked instances using the helpers (or related clean-ups), with
many more waiting at the ready to be taken via subsystem-specific
trees[2].
The new helpers are:
- struct_group() for gaining struct member range introspection
- memset_after() and memset_startat() for clearing to the end of
structures
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in
structs
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage
under GCC, and to prepare to fix the currently broken Clang support.
Finishing this work is part of the larger series[0], but depends on
all the false positives and buffer overflow bug fixes to have landed
already and those that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a
compile-time and run-time tests are added for FORTIFY_SOURCE and the
mem*()-family functions respectively. The compile time tests have
found a legitimate (though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage
that result in no known object code differences.
After this series (and the changes that have now landed via netdev and
usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds.
However, due corner cases in GCC[3] and Clang[4], I have not included
the last two patches that turn on these options, as I don't want to
introduce any known warnings to the build. Hopefully these can be
solved soon"
Link: https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/ [0]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE [1]
Link: https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/ [2]
Link: https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/ [3]
Link: https://bugs.llvm.org/show_bug.cgi?id=51682 [4]
Link: https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/ [5]
Link: https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/ [6]
* tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits)
fortify: strlen: Avoid shadowing previous locals
compiler-gcc.h: Define __SANITIZE_ADDRESS__ under hwaddress sanitizer
treewide: Replace 0-element memcpy() destinations with flexible arrays
treewide: Replace open-coded flex arrays in unions
stddef: Introduce DECLARE_FLEX_ARRAY() helper
btrfs: Use memset_startat() to clear end of struct
string.h: Introduce memset_startat() for wiping trailing members and padding
xfrm: Use memset_after() to clear padding
string.h: Introduce memset_after() for wiping trailing members/padding
lib: Introduce CONFIG_MEMCPY_KUNIT_TEST
fortify: Add compile-time FORTIFY_SOURCE tests
fortify: Allow strlen() and strnlen() to pass compile-time known lengths
fortify: Prepare to improve strnlen() and strlen() warnings
fortify: Fix dropped strcpy() compile-time write overflow check
fortify: Explicitly disable Clang support
fortify: Move remaining fortify helpers into fortify-string.h
lib/string: Move helper functions out of string.c
compiler_types.h: Remove __compiletime_object_size()
cm4000_cs: Use struct_group() to zero struct cm4000_dev region
can: flexcan: Use struct_group() to zero struct flexcan_regs regions
...
by confidential computing solutions to query different aspects of the
system. The intent behind it is to unify testing of such aspects instead
of having each confidential computing solution add its own set of tests
to code paths in the kernel, leading to an unwieldy mess.
-----BEGIN PGP SIGNATURE-----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=Na0U
-----END PGP SIGNATURE-----
Merge tag 'x86_cc_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull generic confidential computing updates from Borislav Petkov:
"Add an interface called cc_platform_has() which is supposed to be used
by confidential computing solutions to query different aspects of the
system.
The intent behind it is to unify testing of such aspects instead of
having each confidential computing solution add its own set of tests
to code paths in the kernel, leading to an unwieldy mess"
* tag 'x86_cc_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide: Replace the use of mem_encrypt_active() with cc_platform_has()
x86/sev: Replace occurrences of sev_es_active() with cc_platform_has()
x86/sev: Replace occurrences of sev_active() with cc_platform_has()
x86/sme: Replace occurrences of sme_active() with cc_platform_has()
powerpc/pseries/svm: Add a powerpc version of cc_platform_has()
x86/sev: Add an x86 version of cc_platform_has()
arch/cc: Introduce a function to check for confidential computing features
x86/ioremap: Selectively build arch override encryption functions
scsi_dma_map() was reporting a failure during boot on an AMD machine
with the IOMMU enabled.
scsi_dma_map failed: request for 36 bytes!
The issue was tracked down to a mistake in logic: should not return
an error if iommu_deferred_attach() returns zero.
Reported-by: Marshall Midden <marshallmidden@gmail.com>
Fixes: dabb16f672 ("iommu/dma: return error code from iommu_dma_map_sg()")
Link: https://lore.kernel.org/all/CAD2CkAWjS8=kKwEEN4cgVNjyFORUibzEiCUA-X+SMtbo0JoMmA@mail.gmail.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20211027174757.119755-1-logang@deltatee.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
DART has an additional global register to control which streams are
isolated. This register is a bit redundant since DART_TCR can already
be used to control isolation and is usually initialized to DART_STREAM_ALL
by the time we get control. Some DARTs (namely the one used for the audio
controller) however have some streams disabled initially. Make sure those
work by initializing DART_STREAMS_ENABLE during reset.
Reported-by: Martin Povišer <povik@protonmail.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20211019162253.45919-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The __domain_mapping() always removes the pages in the range from
'iov_pfn' to 'end_pfn', but the 'end_pfn' is always the last pfn
of the range that the caller wants to map.
This would introduce too many duplicated removing and leads the
map operation take too long, for example:
Map iova=0x100000,nr_pages=0x7d61800
iov_pfn: 0x100000, end_pfn: 0x7e617ff
iov_pfn: 0x140000, end_pfn: 0x7e617ff
iov_pfn: 0x180000, end_pfn: 0x7e617ff
iov_pfn: 0x1c0000, end_pfn: 0x7e617ff
iov_pfn: 0x200000, end_pfn: 0x7e617ff
...
it takes about 50ms in total.
We can reduce the cost by recalculate the 'end_pfn' and limit it
to the boundary of the end of this pte page.
Map iova=0x100000,nr_pages=0x7d61800
iov_pfn: 0x100000, end_pfn: 0x13ffff
iov_pfn: 0x140000, end_pfn: 0x17ffff
iov_pfn: 0x180000, end_pfn: 0x1bffff
iov_pfn: 0x1c0000, end_pfn: 0x1fffff
iov_pfn: 0x200000, end_pfn: 0x23ffff
...
it only need 9ms now.
This also removes a meaningless BUG_ON() in __domain_mapping().
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Tested-by: Liujunjie <liujunjie23@huawei.com>
Link: https://lore.kernel.org/r/20211008000433.1115-1-longpeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-10-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
update_pasid() and its call chain are currently unused in the tree because
Thomas disabled the ENQCMD feature. The feature will be re-enabled shortly
using a different approach and update_pasid() and its call chain will not
be used in the new approach.
Remove the useless functions.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210920192349.2602141-1-fenghua.yu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The IOMMU VT-d implementation uses the first level for GPA->HPA translation
by default. Although both the first level and the second level could handle
the DMA translation, they're different in some way. For example, the second
level translation has separate controls for the Access/Dirty page tracking.
With the first level translation, there's no such control. On the other
hand, the second level translation has the page-level control for forcing
snoop, but the first level only has global control with pasid granularity.
This uses the second level for GPA->HPA translation so that we can provide
a consistent hardware interface for use cases like dirty page tracking for
live migration.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210926114535.923263-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
An iommu domain could be allocated and mapped before it's attached to any
device. This requires that in scalable mode, when the domain is allocated,
the format (FL or SL) of the page table must be determined. In order to
achieve this, the platform should support consistent SL or FL capabilities
on all IOMMU's. This adds a check for this and aborts IOMMU probing if it
doesn't meet this requirement.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210926114535.923263-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When the dmar translation fault happens, the kernel prints a single line
fault reason with corresponding hexadecimal code defined in the Intel VT-d
specification.
Currently, when user wants to debug the translation fault in detail,
debugfs is used for dumping the dmar_translation_struct, which is not
available when the kernel failed to boot.
Dump the DMAR translation structure, pagewalk the IO page table and print
the page table entry when the fault happens.
This takes effect only when CONFIG_DMAR_DEBUG is enabled.
Signed-off-by: Kyung Min Park <kyung.min.park@intel.com>
Link: https://lore.kernel.org/r/20210815203845.31287-1-kyung.min.park@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Handling of intel_iommu kernel command line option should return "true" to
indicate option is valid and so avoid logging it as unknown by the core
parsing code.
Also log unknown sub-options at the notice level to let user know of
potential typos or similar.
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://lore.kernel.org/r/20210831112947.310080-1-tvrtko.ursulin@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
My previous bugfix ended up making things worse for the QCOM IOMMU
driver when it forgot to add the Kconfig symbol that is getting used to
control the compilation of the SMMU implementation specific code
for Qualcomm.
Fixes: 424953cf3c ("qcom_scm: hide Kconfig symbol")
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/lkml/20211010023350.978638-1-dmitry.baryshkov@linaro.org/
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The
fix we agreed on in the end is to make this symbol selected by any
driver using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in v5.15.
There is a small merge conflict against an earlier partial fix for the
QCOM_SCM dependency problems.
Finally, the branch also includes a small unrelated build fix for NOMMU
architectures.
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=187C
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
The SID configuration requirement for Modem on SC7280 is similar to the
ones found on SC7180/SDM845 SoCs. So, add the SC7280 modem compatible to
the list to defer the programming of the modem SIDs to the kernel.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1631886935-14691-5-git-send-email-sibis@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add compatible for QCM2290 SMMU to use the Qualcomm Technologies, Inc.
specific implementation.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1633096832-7762-1-git-send-email-loic.poulain@linaro.org
[will: Sort by alphabetical order, add commit message]
Signed-off-by: Will Deacon <will@kernel.org>
1. Build command CMD_SYNC cannot fail. So the return value can be ignored.
2. The arm_smmu_cmdq_build_cmd() almost never fails, the addition of
"unlikely()" can optimize the instruction pipeline.
3. Check the return value in arm_smmu_cmdq_batch_add().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210818080452.2079-2-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Pre-zeroing the batched commands structure is inefficient, as individual
commands are zeroed later in arm_smmu_cmdq_build_cmd(). Therefore, only
the member 'num' needs to be initialized to 0.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20210817113411.1962-1-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Replace uses of mem_encrypt_active() with calls to cc_platform_has() with
the CC_ATTR_MEM_ENCRYPT attribute.
Remove the implementation of mem_encrypt_active() across all arches.
For s390, since the default implementation of the cc_platform_has()
matches the s390 implementation of mem_encrypt_active(), cc_platform_has()
does not need to be implemented in s390 (the config option
ARCH_HAS_CC_PLATFORM is not set).
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210928191009.32551-9-bp@alien8.de
Replace uses of sme_active() with the more generic cc_platform_has()
using CC_ATTR_HOST_MEM_ENCRYPT. If future support is added for other
memory encryption technologies, the use of CC_ATTR_HOST_MEM_ENCRYPT
can be updated, as required.
This also replaces two usages of sev_active() that are really geared
towards detecting if SME is active.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210928191009.32551-6-bp@alien8.de
This patch makes iommu/amd call report_iommu_fault() when an I/O page
fault occurs, which has two effects:
1) It allows device drivers to register a callback to be notified of
I/O page faults, via the iommu_set_fault_handler() API.
2) It triggers the io_page_fault tracepoint in report_iommu_fault()
when an I/O page fault occurs.
The latter point is the main aim of this patch, as it allows
rasdaemon-like daemons to be notified of I/O page faults, and to
possibly initiate corrective action in response.
A number of other IOMMU drivers already use report_iommu_fault(), and
I/O page faults on those IOMMUs therefore already trigger this
tracepoint -- but this isn't yet the case for AMD-Vi and Intel DMAR.
The AMD IOMMU specification suggests that the bit in an I/O page fault
event log entry that signals whether an I/O page fault was for a read
request or for a write request is only meaningful when the faulting
access was to a present page, but some testing on a Ryzen 3700X suggests
that this bit encodes the correct value even for I/O page faults to
non-present pages, and therefore, this patch passes the R/W information
up the stack even for I/O page faults to non-present pages.
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Link: https://lore.kernel.org/r/YVLyBW97vZLpOaAp@wantstofly.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pass the non-aligned size to __iommu_dma_map when using swiotlb bounce
buffers in iommu_dma_map_page, to account for min_align_mask.
To deal with granule alignment, __iommu_dma_map maps iova_align(size +
iova_off) bytes starting at phys - iova_off. If iommu_dma_map_page
passes aligned size when using swiotlb, then this becomes
iova_align(iova_align(orig_size) + iova_off). Normally iova_off will be
zero when using swiotlb. However, this is not the case for devices that
set min_align_mask. When iova_off is non-zero, __iommu_dma_map ends up
mapping an extra page at the end of the buffer. Beyond just being a
security issue, the extra page is not cleaned up by __iommu_dma_unmap.
This causes problems when the IOVA is reused, due to collisions in the
iommu driver. Just passing the original size is sufficient, since
__iommu_dma_map will take care of granule alignment.
Fixes: 1f221a0d0d ("swiotlb: respect min_align_mask")
Signed-off-by: David Stevens <stevensd@chromium.org>
Link: https://lore.kernel.org/r/20210929023300.335969-8-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add an argument to swiotlb_tbl_map_single that specifies the desired
alignment of the allocated buffer. This is used by dma-iommu to ensure
the buffer is aligned to the iova granule size when using swiotlb with
untrusted sub-granule mappings. This addresses an issue where adjacent
slots could be exposed to the untrusted device if IO_TLB_SIZE < iova
granule < PAGE_SIZE.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929023300.335969-7-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Introduce a new dev_use_swiotlb function to guard swiotlb code, instead
of overloading dev_is_untrusted. This allows CONFIG_SWIOTLB to be
checked more broadly, so the swiotlb related code can be removed more
aggressively.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929023300.335969-6-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Fold the _swiotlb helper functions into the respective _page functions,
since recent fixes have moved all logic from the _page functions to the
_swiotlb functions.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210929023300.335969-5-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Calling the iommu_dma_sync_*_for_cpu functions during unmap can cause
two copies out of the swiotlb buffer. Do the arch sync directly in
__iommu_dma_unmap_swiotlb instead to avoid this. This makes the call to
iommu_dma_sync_sg_for_cpu for untrusted devices in iommu_dma_unmap_sg no
longer necessary, so move that invocation later in the function.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210929023300.335969-4-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When calling arch_sync_dma, we need to pass it the memory that's
actually being used for dma. When using swiotlb bounce buffers, this is
the bounce buffer. Move arch_sync_dma into the __iommu_dma_map_swiotlb
helper, so it can use the bounce buffer address if necessary.
Now that iommu_dma_map_sg delegates to a function which takes care of
architectural syncing in the untrusted device case, the call to
iommu_dma_sync_sg_for_device can be moved so it only occurs for trusted
devices. Doing the sync for untrusted devices before mapping never
really worked, since it needs to be able to target swiotlb buffers.
This also moves the architectural sync to before the call to
__iommu_dma_map, to guarantee that untrusted devices can't see stale
data they shouldn't see.
Fixes: 82612d66d5 ("iommu: Allow the iommu/dma api to use bounce buffers")
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210929023300.335969-3-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The is_swiotlb_buffer function takes the physical address of the swiotlb
buffer, not the physical address of the original buffer. The sglist
contains the physical addresses of the original buffer, so for the
sync_sg functions to work properly when a bounce buffer might have been
used, we need to use iommu_iova_to_phys to look up the physical address.
This is what sync_single does, so call that function on each sglist
segment.
The previous code mostly worked because swiotlb does the transfer on map
and unmap. However, any callers which use DMA_ATTR_SKIP_CPU_SYNC with
sglists or which call sync_sg would not have had anything copied to the
bounce buffer.
Fixes: 82612d66d5 ("iommu: Allow the iommu/dma api to use bounce buffers")
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929023300.335969-2-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
clang-14 notices that a comparison is never true when
CONFIG_PHYS_ADDR_T_64BIT is disabled:
drivers/iommu/mtk_iommu.c:553:34: error: result of comparison of constant 5368709120 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (dom->data->enable_4GB && pa >= MTK_IOMMU_4GB_MODE_REMAP_BASE)
~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add an explicit check for the type of the variable to skip the check
and the warning in that case.
Fixes: b4dad40e4f ("iommu/mediatek: Adjust the PA for the 4GB Mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210927121857.941160-1-arnd@kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
sid2groups keeps track of which stream id combinations belong to a
iommu_group to assign those correctly to devices.
When a iommu_group is freed a stale pointer will however remain in
sid2groups. This prevents devices with the same stream id combination
to ever be attached again (see below).
Fix that by creating a shadow copy of the stream id configuration
when a group is allocated for the first time and clear the sid2group
entry when that group is freed.
# echo 1 >/sys/bus/pci/devices/0000\:03\:00.0/remove
pci 0000:03:00.0: Removing from iommu group 1
# echo 1 >/sys/bus/pci/rescan
[...]
pci 0000:03:00.0: BAR 0: assigned [mem 0x6a0000000-0x6a000ffff 64bit pref]
pci 0000:03:00.0: BAR 2: assigned [mem 0x6a0010000-0x6a001ffff 64bit pref]
pci 0000:03:00.0: BAR 6: assigned [mem 0x6c0100000-0x6c01007ff pref]
tg3 0000:03:00.0: Failed to add to iommu group 1: -2
[...]
Fixes: 46d1fb072e ("iommu/dart: Add DART iommu driver")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Tested-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210924134502.15589-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add r8a77980 (R-Car V3H) to the list of supported devices. The hardware
is the same as on already-supportred V3M and other R-Car Gen3 chips.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20210923191115.22864-1-nikita.yoush@cogentembedded.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
719a193356 ("iommu/vt-d: Tweak the description of a DMA fault") changed
the DMA fault reason from hex to decimal. It also added "0x" prefixes to
the PCI bus/device, e.g.,
- DMAR: [INTR-REMAP] Request device [00:00.5]
+ DMAR: [INTR-REMAP] Request device [0x00:0x00.5]
These no longer match dev_printk() and other similar messages in
dmar_match_pci_path() and dmar_acpi_insert_dev_scope().
Drop the "0x" prefixes from the bus and device addresses.
Fixes: 719a193356 ("iommu/vt-d: Tweak the description of a DMA fault")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210903193711.483999-1-helgaas@kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210922054726.499110-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
apple_dart_tlb_flush_{all,walk} expect to get a struct apple_dart_domain
but instead get a struct iommu_domain right now. This breaks those two
functions and can lead to kernel panics like the one below.
DART can only invalidate the entire TLB and apple_dart_iotlb_sync will
already flush everything. There's no need to do that again inside those
two functions. Let's just drop them.
pci 0000:03:00.0: Removing from iommu group 1
Unable to handle kernel paging request at virtual address 0000000100000023
[...]
Call trace:
_raw_spin_lock_irqsave+0x54/0xbc
apple_dart_hw_stream_command.constprop.0+0x2c/0x130
apple_dart_tlb_flush_all+0x48/0x90
free_io_pgtable_ops+0x40/0x70
apple_dart_domain_free+0x2c/0x44
iommu_group_release+0x68/0xac
kobject_cleanup+0x4c/0x1fc
kobject_cleanup+0x14c/0x1fc
kobject_put+0x64/0x84
iommu_group_remove_device+0x110/0x180
iommu_release_device+0x50/0xa0
[...]
Fixes: 46d1fb072e ("iommu/dart: Add DART iommu driver")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210921153934.35647-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IOVA cookies are now got and put by core code, so we no longer need to
export these to modular drivers. The export for getting MSI cookies
stays, since VFIO can still be a module, but it was already relying on
someone else putting them, so that aspect is unaffected.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/ef89db54a27df7d8bc0af094c7d7b204fd61774c.1631531973.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The addition of the DART driver crossed over with moving IOVA cookie
management into core code; clean up the now-unnecessary remnants here.
Acked-by: Sven Peter <sven@svenpeter.dev>
Tested-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/edb72b4965baa8999dd70b8294785d6deebd4183.1631531973.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add support for r8a779a0 (R-Car V3U). The IPMMU hardware design
of this SoC differs than others. So, add a new ipmmu_features for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210907083020.907648-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Niklas Schnelle