Store the last used mclk configuration for the PLL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
mcp_priv() does unexpected things when passed a void pointer. Make it
a typed inline function, which ensures that it works correctly in
these cases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 5dd7bf59e0.
Conflicts:
scripts/mod/file2alias.c
This change is wrong on many levels. First and foremost, it causes a
regression. On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:
ucb1x00 ID not found: 1005
0x1005 is a valid ID for the UCB1300 device.
Secondly, this patch is way over the top in terms of complexity. The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver. Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
* git://git.infradead.org/battery-2.6: (68 commits)
power_supply: Mark da9052 driver as broken
power_supply: Drop usage of nowarn variant of sysfs_create_link()
s3c_adc_battery: Average over more than one adc sample
power_supply: Add DA9052 battery driver
isp1704_charger: Fix missing check
jz4740-battery: Fix signedness bug
power_supply: Assume mains power by default
sbs-battery: Fix devicetree match table
ARM: rx51: Add bq27200 i2c board info
sbs-battery: Change power supply name
devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
devicetree-bindings: Add vendor entry for Smart Battery Systems
sbs-battery: Rename internals to new name
bq20z75: Rename to sbs-battery
wm97xx_battery: Use DEFINE_MUTEX() for work_lock
max8997_charger: Remove duplicate module.h
lp8727_charger: Some minor fixes for the header
lp8727_charger: Add header file
power_supply: Convert drivers/power/* to use module_platform_driver()
power_supply: Add "unknown" in power supply type
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits)
regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
regulator: max8925: fix enabled/disabled judgement mistake
regulator: add regulator_bulk_force_disable function
regulator: pass regulator_register of_node in fixed voltage driver
regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR
regulator: Enable supply regulator if child rail is enabled.
regulator: mc13892: Convert to devm_kzalloc()
regulator: mc13783: Convert to devm_kzalloc()
regulator: Fix checking return value of create_regulator
regulator: Fix the error handling if create_regulator fails
regulator: Export regulator_is_supported_voltage()
regulator: mc13892: add device tree probe support
regulator: mc13892: remove the unnecessary prefix from regulator name
regulator: Convert wm831x regulator drivers to devm_kzalloc()
regulator: da9052: Staticize non-exported symbols
regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
regulator: Update da9052-regulator for DT changes
regulator: DA9052/53 Regulator support
regulator: pass device_node to of_get_regulator_init_data()
regulator: If a single voltage is set with device tree then set apply_uV
...
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
S5M series are pmic including mutiple functional devices.
It can support PMIC, RTC, Battery charger, codec.
This patch implement core driver for s5m series.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMPE801 is a GPIO expander. Registers for 801 are much different from other
variants. This patch adds support for STMPE801 in stmpe mfd driver.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMPE610 is very much like STMPE811, except the number of gpio pins, which is 8
in 811 and 6 in 610. This patch adds support for variant 610. STMPE610 will
share most of the code with STMPE811.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Few STMPE controller can have register interface over SPI or I2C. Current
implementation only supports I2C and all code is present in a single file
stmpe.c. It would be better to separate out I2C interface specific code from
controller specific code. Later SPI specific code can be added in a separate
file.
This patch separates out I2C and controller specific code into separate files,
making stmpe.c independent of I2C.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8997 device does not support LED control function of it.
To enable MAX8997-LED driver, platform data and devices for LED are updated.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
struct wm8994 includes a mutex so we need to include mutex.h before we
declare it. All current users rely on this being done implicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver has no need to modify the regulator_init_data so declare it
const to allow machine code to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the ADC is being prepared for a single or multiple channel reading,
the adc0 register is reconfigured without taking the lithium cell, charge
current and battery current reading enable bits into account. Which results
in clearing the bits.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, MAX8997 device does not support MUIC function of it.
To add MAX8997 MUIC driver, header file should be updated.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert the 88pm860x normal bank register read/write to
use the register map API.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On many boards, stmpe is present as an separate device (not as part of SoC).
Here gpio lines are mostly used for getting interrupts. This patch adds in
support to handle irq over gpio pin.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It adds device tree probe support for mc13892-regulator driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DA9052/53 is a highly integrated PMIC subsystem with supply domain
flexibility to support wide range of high performance application.
It provides voltage regulators, GPIO controller, Touch Screen, RTC, Battery
control and other functionality.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Factor out the irq_chip implementation, substantially reducing the code
size for the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
For later chip revisions the WM1811 GPIO6 register is always volatile so
store the device revision when initialising the driver and then check at
runtime if we're running on a newer device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
struct wm8994 includes a mutex so we need to include mutex.h before we
declare it. All current users rely on this being done implicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
The driver has no need to modify the regulator_init_data so declare it
const to allow machine code to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
As part of this we provide information about the registers that exist in
the device to the regmap core, drop the small amount of cache that the
core had been using and let regmap do the sync.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add a bunch of definitions for wm8994 registers that are not currently
used by software.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Allow systems to override the default microphone detection rates using
platform data in case the settings are not suitable (eg, due to an
unusually noisy jack).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811A features an advanced low power accessory detection subsystem
which allows the device to be maintained in a very low power state while
the system is idle without sacrificing any accessory detection features.
Implement software support for this, automatically managing the power
configuration of the device depending on the detected accessory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8958 and WM1811 support detecting a range of buttons. Allow the
user to provide platform data enabling more of these levels without
having to write a custom detection handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The power core infrastructure allow external power change
events to be passed to drivers what are listed in the
supplied_to call back field. Enable this feature by
allowing the supplied_to field to be passed to the driver.
This feature will enable drivers named in the supplied_to
field that have a external_power_changed callback to be
notified when power was been turned on or off.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
On brownstone rev 4 ac-insert detect is handled by vbus.
allow the platform code to configure the disabling of insert
by setting no_insert_detect.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Brownstone does not have temperature reading circuit hooked up.
This leads to spurious interrupts.
Allow the platform layer to indicate no temperature circuit
and do not activate interrupts if no temperature control is set
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.
Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain
With above expr, number of voltages that can be selected is
step value count * gain count
constant for gain count will be called VDD1_2_NUM_VOLT_COARSE
existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Create an array of fixed size for the platform to pass regulator
initalization data through.
Passing an array of pointers to init data also allows more flexible
definition of init data as well as prevents reading past the end of the
array should the platform define an incorrectly sized array.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the regulator defintions to the header so that platform board file
can use them to configure specific regulators.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Occasionally we may see an accessory reported before we have a stable
impedance for the accessory. If this happens then reread the status in
order to ensure that the handler can take the appropriate action for the
status change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
I missed to include a patch adding the new silicon revision define
CUT3P3 and remove the retired CUT0 versions of AB8500. Also delete
the reference to the retired AB3550 from the header.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Peter Ujfalusi