The local loopback should only be enabled for VSIs that are supporting
cascaded VEBs or VEPA setups. This is not the case here, and we need
to stop the VEB from echoing the VMDQ VSI packets back at the VSI.
Change-ID: I9dfb6ac79db24d04360d7efde62d81e20abc5090
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vf_id needs to be offset by the vf_base_id from hw function capabilities
for the case of multiple PFs.
Change-ID: I20ca8621f98e9cdf98649380b8eeaa35db52677c
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the HW registers are no longer in debug mode and many are
locked down for writes, we need to expose the Firmware API request
used to do writes on the driver's behalf.
Change-ID: I09a05c4dc9ea0b24c00193faac34d7799eaa8496
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds newly added FCoE files to the build but only if FCoE module is configured.
Also, updates i40e document for added FCoE support.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds FCoE specific code to existing i40e core driver to:-
1. have separate FCoE VSI with additional FCoE queues pairs.
2. have FCoE related hash defines.
3. have additional FCoE related stats code.
4. export and then re-use existing functions required by FCoE build.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds FCoE ( Fibre Channel Over Ethernet ) code for
Intel XL710 adapters. This patch is limited to only new FCoE
offloads code in newly added files by this patch and then
following patches in the series modifies rest of the existing
driver to enable FCoE with i40e driver.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the spinlocks around the ethtool get and set settings
functions and within the link adjustment callback routine.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of managed interfaces like
devm_ioremap_resource and does away with the calls to free the
allocated memory in the probe and remove functions. Also, some
labels and variable are done away with. This fixes a bug as there
was a missing release_mem_region in the remove function.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of devm_ioremap_resource, devm_kmalloc and
does away with the functions to free the allocated memory in the probe
and remove functions. Also, some labels are done away with. A bug is
fixed as two regions are allocated in the probe function, but only one
is freed in the remove function.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of managed interfaces like
devm_ioremap_resource and does away with the functions to free the
allocated memory in the probe and remove functions. Also, many labels
are done away with. The field size in no longer needed and is hence
removed from the struct net_local.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to delete an existing FW-dump in Lancer via ethtool.
Initiating a new dump is not allowed if a FW dump is already present in the
adapter. The existing dump has to be first explicitly deleted.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_set_vf_mac() call may be issued for a mac-addr that is already
active on a VF. If so, silently ignore the request.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old versions of BE3 FW may not support cmds to re-provision (and hence
optimize) resources/queues in SR-IOV config. Do not treat this FW cmd
failure as fatal and fail the function initialization. Instead, just
enable SR-IOV with the resources provided by the FW.
Prior to the "create optimal number of queues on SR-IOV config" patch
such failures were ignored.
Fixes: bec84e6b2 ("create optimal number of queues on SR-IOV config")
Reported-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dm9000_release_board() function is called with NULL ->data_req and
->addr_req pointers if dm9000_probe() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add few helper functions to support a mechanism of getting an MPT,
modifying it and updating the HCA with the modified object.
The code takes 2 paths, one for directly changing the MPT (and
sometimes its related MTTs) and another one which queries the MPT and
updates the HCA via fw command SW2HW_MPT. The first path is used in
native mode; the second path is slower and is used only in SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In the shutdown path, when be2net calls pci_disable_msix(), it
complains (BUG_ON) that irqs requested by ocrdma driver are still in
use. This patch fixes this problem by issuing shutdown event to
ocrdma from be2net shutdown path. As part of shutdown event
processing, ocrdma driver will free up all the resources and free
irqs. Once this completes be2net completes pci_disable_msix
successfully.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds and modifies code to support multiple Multicast and Unicast
Synopsys MAC filter configurations. The default configuration is defined to
support legacy driver behavior, which is 64 Multicast bins. The Unicast
filter code previously assumed all controllers support 32 or 16 Unicast
addresses based on controller version number, but this has been corrected
to support a default of 1 Unicast address. The filter configuration may
be specified through the devicetree using a Synopsys specific device tree
entry. This information was verified with Synopsys through
Synopsys Support Case #8000684337 and shared with the maintainer.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the check for the number of mulitcast addresses
when using hash based filtering since it's not necessary. If the number
of multicast addresses in the list exceeds the number of multicast hash
bins, the bins will "fold" over into one of the bins configured and
enabled for the particular component instance.
The default number of maximum unicast addresses was changed from 32 to 1
since this number is not dependent on the component revision. The maximum
number of multicast and unicast addresses is dependent on the configuration
of the Synopsys EMAC configured by the SOC architect at the time the
features were selected and configured for a particular component. Sadly,
Synopsys does not provide a way to query the precise number supported
by a particular component, so we must fall back on a devicetree entry.
This configuration could vary from vendor to vendor (such as STMicro,
Altera, etc).
The multicast bins are set for every possible filtering case (including
no entries) - previously the bits were set only if multicast filter entries
were present.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synopsys EMAC can be configured for different numbers of multicast hash
bins and perfect filter entries at device creation time and there's no way
to query this configuration information at runtime. As a result, a devicetree
parameter is required in order for the driver to program these filters
correctly for a particular device instance. This patch modifies the
10/100/1000 MAC software interface such that these configuration parameters
can be set at initialization time.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix one misspelled word reported by codespell.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit "e29aa33 bna: Enable Multi Buffer RX" is causing
a performance regression. It does not properly update 'cmpl' pointer
at the end of the loop in NAPI handler bnad_cq_process(). The result is
only one packet / per NAPI-schedule is processed.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for traffic classes as well as support
for Data Center Bridging interfaces related to traffic classes
and priority flow control.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the fifo sizes for the queues and enabling the queues
use the number of active Tx and Rx queues that have been enabled
not the maximum number available.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Tx and Rx hardware timestamping.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the event flow, we currently pass only a port number in the
void *data argument. Rather than pass a pointer to the event handlers,
we should use an "unsigned long" parameter, and pass the port number
value directly.
In the future, if necessary for some events, we can use the unsigned long
parameter to pass a pointer.
Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places where parameters which should be u8/u16 were
integer type.
Additionally, in 2 places, a check for a non-null pointer was added
before dereferencing the pointer (this is actually a bug fix).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for a new mlx5 device which is VPI (i.e., ports can be
either IB or ETH), move the pci device functionality from mlx5_ib
to mlx5_core.
This involves the following changes:
1. Move mlx5_core_dev struct out of mlx5_ib_dev. mlx5_core_dev
is now an independent structure maintained by mlx5_core.
mlx5_ib_dev now has a pointer to that struct.
This requires changing a lot of places where the core_dev
struct was accessed via mlx5_ib_dev (now, this needs to
be a pointer dereference).
2. All PCI initializations are now done in mlx5_core. Thus,
it is now mlx5_core which does pci_register_device (and not
mlx5_ib, as was previously).
3. mlx5_ib now registers itself with mlx5_core as an "interface"
driver. This is very similar to the mechanism employed for
the mlx4 (ConnectX) driver. Once the HCA is initialized
(by mlx5_core), it invokes the interface drivers to do
their initializations.
4. There is a new event handler which the core registers:
mlx5_core_event(). This event handler invokes the
event handlers registered by the interfaces.
Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver should fill magic field of ethtool_eeprom struct in .get_eeprom
and validate it in .set_eeprom. The bna incorrectly validates it in both
and this makes its .get_eeprom interface unusable.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the register offsets and bit descriptions from the au1000.h header
to their only user, the au1000_eth.c driver.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: netdev@vger.kernel.org
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is similar to commit 4d12bc63ab ("net: mvneta: fix
operation in 10 Mbit/s mode"), but this time for the mvpp2 driver. The
driver was properly taking into account the 1 Gbit/s and 100 Mbit/s
speeds, but not the 10 Mbit/s, which was handled as 100
Mbit/s. However, the MVPP2_GMAC_CONFIG_MII_SPEED bit in the
MVPP2_GMAC_AUTONEG_CONFIG register must remain cleared to allow 10
Mbit/s operation. This commit therefore fixes 10 Mbit/s operation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__iowrite64_copy() isn't quite the same as efx_memcpy_64(), but
it looks close enough:
- The length is in units of qwords not bytes
- It never byte-swaps, but that doesn't make a difference now as PIO
is only enabled for x86_64
- It doesn't include any memory barriers, but that's OK as there is a
barrier just before pushing the doorbell
- mlx4_en uses it for the same purpose
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver explicitly clears a field that is unused and about to be
removed. Remove the initialization.
All fields in skb_shared_info before dataref are cleared in
__alloc_skb, so the removal is safe even while syststamp exists.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware timestamps can be exposed to userspace in raw hardware format
(hwtstamp) as well as converted to system time (syststamp). The second
variant is deprecated and only implemented by this driver.
The preferred method of hardware timestamp generation is to combine
hwtstamp with a device PTP clock. Octeon has its own PTP library
that relies on a shared memory interface to the PTP clock device.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sunvnet driver doesn't check whether or not a port is connected when
transmitting packets, which results in failures if a port fails to connect
(e.g., due to a version mismatch). The original code also assumes
unnecessarily that the first port is up and a switch, even though there is
a flag for switch ports.
This patch only matches a port if it is connected, and otherwise uses the
switch_port flag to send the packet to a switch port that is up.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a function, and associated calls, to flush writes to (read) the LPIC
MAC register before entering the shutdown flow. This fixes the problem
of the PHY never negotiating a 100M link (if both sides of the link support
EEE and 100M link) when Runtime PM is enabled.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The process of shutting down the system causes a call to the close PM
callback. The reset in close causes a loss of link, and the resultant
LSC interrupt causes the Runtime PM idle callback to be called. The
check for link (while link is down) in the idle callback is wiping the
information about the EEE ability of the link partner. The information is
still gone when the PHY is powered back up in the shutdown flow. This
causes EEE in S5 to fail when Runtime PM is active.
Save the link partner's EEE ability in the idle callback so that a Runtime
PM event will not cause a loss of this information.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On I217 and newer hardware, EEE is enabled in the PHY by the software
when link is up and disabled by the hardware when link is lost.
To enable EEE in Sx (When both ends of the link support, and are enabled
for, EEE and 100Mbps), we need to disable LPLU and configure the PHY to
automatically enable EEE when link is up, since there will be no software
to complete the task.
To configure this in the PHY, the Auto Enable LPI bit in the Low Power
Idle GPIO Control register must be set. For normal operation in S0, this
bit must be cleared.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding code to check and respond to previously ignored return values
from NVM access functions.
Issue discovered through static analysis.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modifying the jumbo frame workaround for 82579, i217 and i218 client parts
to increase the gap between the read and write pointers in the Tx FIFO.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make return values more direct, eliminating some gotos and
otherwise unneeded conditionals. This also eliminates some
local variables. Also a few minor cleanups in affected code
so checkpatch won't complain.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All of the code involved with returning the supported physical
layer is actually unused, so delete it.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ixgbe_write_mbx is called and no mbx->ops.write method
exists, no error code is returned. The corresponding read
function explicitly returns an error in such a case as do
other functions, so this appears to be a minor bug. Fix
it for consistency, and generate return values directly
to make things clearer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the function ixgbe_get_swfw_sync_semaphore, an incorrect
check was treating success as failure and vice-versa. This led
to manipulating the IXGBE_SWFW_SYNC register without holding
the software semaphore first, which is an error. In addition,
if getting the REGSMP bit in the IXGBE_SW_FW_SYNC register
timed out, no error code would be returned, making the caller
think that it had successfully acquired the lock. Fix both of
those issues and clean up the function a bit, such as make the
name in the comment match the function.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Failure to acquire the semaphore would lead to a spurious release
of the semaphore in several functions. Do not release a semaphore
that you did not get.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert some udelay calls to the preferred usleep_range.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When RX checksum offload is enabled at GEM level (bit 24 set in the Network
Control Register), frames with invalid IP, TCP or UDP checksums are
discarted even if promiscuous mode is enabled (bit 4 set in the Network Control
Register).
This was verified with a simple userspace program, which corrupts UDP checksum
using libnetfilter_queue.
Then both IFF_PROMISC bit must be clear in dev->flags and NETIF_F_RXCSUM bit
must be set in dev->features to enable RX checksum offload at GEM level. This
way tcpdump is still able to capture corrupted frames.
Also skb->ip_summed is set to CHECKSUM_UNNECESSARY only when both TCP/IP or
UDP/IP checksums were verified by the GEM. Indeed the GEM may verify only IP
checksum but not the one for ICMP (or other protocol than TCP or UDP).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scatter-gather feature will allow to enable the Generic Segmentation Offload.
Generic Segmentation Offload can be enabled/disabled using ethtool -K DEVNAME gso on|off.
e.g:
ethtool -K eth0 gso off
When enabled, the driver may be provided with socket buffers splitted into many fragments.
These fragments need to be queued into the TX ring in reverse order, starting from to the
last one down to the first one, to avoid a race condition with the MAC.
Especially the 'TX_USED' bit in word 1 of the transmit buffer descriptor of the
first fragment should be cleared at the very final step of the queueing algorithm.
This will tell the hardware that fragments are ready to be sent.
Also since the MAC only update the status word of the first buffer descriptor of the
ethernet frame, the queueing algorithm can no longer expect a 'TX_USED' bit to be set by
the MAC into the buffer descriptor following the one for last fragment of the skb.
This is why the driver sets the 'TX_USED' bit before queueing any fragment, so the end of
queue position is well defined for the MAC.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This addition will also allow to configure DMA burst length.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removing unused function as part of driver cleanup.`
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes sparse warning intrduced by commit 0fef9d0 ("net/mlx4_en: Disable
blueflame using ethtool private flags")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet RX DMA buffers are polled in NAPI work queue other than received
directly in DMA RX interrupt handler.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect check introduced in commit fc5ab020 ("cxgb4: Replaced the
backdoor mechanism to access the HW memory with PCIe Window method"). We where
checking for write operation and doing a read, changed it accordingly.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the CONFIG_PM_SLEEP ifdef by annotating the suspend/resume functions
with '__maybe_unused' in order to keep the code simpler and shorter.
While at it, declare the suspend/resume functions in a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow set_settings() to complete succesfully even if link is
not estabilished and port type isn't known yet.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the AQTX answer comes back with no data, but we still want to print
the descriptor that got written back.
Change-ID: I5f734d99b4c95510987413893f0a34626571d474
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Give link a little more time to come back up after setting flow control
before resetting. In the new NVMs it is taking longer for link to come back.
This causes the driver to attempt to reset the link, which then errors
because the firmware was already in the middle of a reset. Also, initialize
err to 0.
Change-ID: I1cc987a944e389d8909c262da5796f50722b4d6b
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jmyoungx@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reword the error messages. Also add a major version check because
We only want to warn on nvm_minor > expected_minor if
nvm_major == expected_major. Lastly, change an if to an else if
because the two statements will never evaluate to true at the same time.
Change-ID: I6ddf9986f26b35f6879cbeac4fcef04a8497a383
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Copy desc and buffer data even for ARQ events which return error status.
Previously, a check for NVM related AQ commands which is done later in this
function would not recognize that such a command was received and would
not clear nvm_busy flag. This would block access to NVM until a driver reset.
This will fix that.
Change-ID: If69ad74e165b56081c0686b97402511d2e2880c0
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We really don't need to delay an entire millisecond just to get into our
critical section. A microsecond will be sufficient, thank you.
Change-ID: I2d02ece6610007d98cabcb3f42df9a774bb54e59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware design requires that the driver avoid indicating
checksum offload success on some ipv6 frames with extension
headers.
The code needs to just check for the IPV6EXADD bit and if
it is set punt the checksum to the stack. I don't know why
the code was checking TCP on inner protocol, as that code
doesn't make any sense to me but seems wrong, so remove it.
Change-ID: I10d3aacdbb1819fb60b4b0eb80e6cc67ef2c9599
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This implements a state machine intended to support the userland tool for
updating the device eeprom. The state machine implements one-shot reads,
writes, multi-step write sessions, and checksum requests. If we're in the middle
of a multi-step write session, no one should fire off other writes, however, one
shot reads are valid. The userland tool is expected to keep track of its session
status, arrange the placement and ordering of the writes, and deal with the
checksum requirement.
This patch also adds nvmupdate support to ethtool callbacks.
The get_eeprom() and set_eeprom() services in ethtool are used here to
facilitate the userland NVMUpdate tool. The 'magic' value in the get and
set commands is used to pass additional control information for managing
the read and write steps.
The read operation works both as normally expected in the standard ethtool
method, as well as with the extra NVM controls. The write operation
works only for the expanded NVM functions - the normal ethtool method is
not allowed because of the NVM semaphore management needed for multipart
writes, as well as the checksum requirement.
Change-ID: I1d84a170153a9f437906744e2e350fd68fe7563d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
spotted by cppcheck
Signed-off-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version number.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a check and prints the error cause register value when
the hardware detects a malformed packet. This is a very unlikely
scenario but has been seen occasionally, so printing the message to
assist the user.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the display of the minimum link qualification check
if we might be in a virtual machine. This check is incorrect and
misleading in this case, since we actually don't really know what the
available bandwidth is. To do so, we simply check whether each function
on the bus matches our device id. If it doesn't the most likely scenario
is that we're directly assigned to a virtual machine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug in the misuse of the list_for_each macro to loop over every
entry in the bus_list. Instead of attempting to loop over the list from
a random entry point, go up to the bus and use the real list_head entry
point. This prevents the possible read or write of unallocated or
incorrectly addressed memory.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change some uses of strncpy to use the more appropriate strlcpy
when clearing is not needed to prevent information leakage. Also
change some length arguments to use the preferred sizeof form.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_probe, the code at label err_dma can dereference adapter
when it has a NULL value. The check is there to avoid disabling a
disabled device. When adapter is NULL, treat it as if the device
is enabled, because it is enabled in that case.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were two places that used kzalloc() with a multiplied sizeof(),
replace these with kcalloc as recommended by checkpatch.pl.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged two locations that did not comply to "CHECK:
braces {} should be used on all arms of this statement", fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged two blank lines which are not needed, and one that
was missing, fix them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged a lot of "CHECK: Alignment should match open
parenthesis" checks, fix all of them to make the driver neater. While
at it fix some obvious typos and re-arrange some of the lines to avoid
going over 80 columns.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a smaller GPLv2 header and remove all the boilerplate code as well
as the FSF mail address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is beyond silly:
struct timespec ts = ktime_get_ts();
ktime_t ktime = timespec_to_ktime(ts);
Further down the code builds the delta of two ktime_t values and
converts the result to nanoseconds.
Use ktime_get_ns() and replace all the nonsense.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch use the struct pci_device_id instead of using macro
DEFINE_PCI_DEVICE_TABLE which is deprecated and should not be used.
And also moves these ids after probe and remove functionalities.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts to use the macro module_pci_driver, which makes
the code smaller and simpler.
Previously in this driver we are having driver version info will be
printed log buffer based on whether the driver selected as module
or statically into image itself. By using the module_pci_driver that
part of the code removed. For the first time of the device init,
we are making the version info to be printed once.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the setting real tx queue
count error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets shorter than ETH_ZLEN were not padded with zeroes, hence leaking
potentially sensitive information. This bug has been present since the
driver got accepted in commit 1c1008c793
("net: bcmgenet: add main driver file").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to view addresses added by the driver and learnt by the
hardware from ALE table via ethtool register dump interface.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the sfc driver code for implementing busy polling.
It adds ndo_busy_poll method and locking between it and napi poll.
It also adds each napi to the napi_hash right after netif_napi_add().
Uses efx_start_eventq and efx_stop_eventq in the self tests.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory is limited, reduce number of rx and tx rings.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in kdump kernel, reduce number of resources allocated for
the hardware. This will enable the NIC to operate in this low memory
environment at the expense of performance and some features not related
to the basic NIC functionality.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the user to turn off the hardware feature called BlueFlame.
Since it is something specific to mlx4_en hardware, we control
the feature via ethtool private flags.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is down dev_addr is changed (e.g. by bonding) but current_mac
is not touched. When port is up again, hash_mac is updated to dev_addr,
but current_mac isn't. This leads to inconsistency between current_mac
and mac_hash. Because of that, mlx4_en_replace_mac() fails to find
current_mac in mac_hash.
Fix is to reset current_mac to dev_addr when port is up - as we do for
mac_hash.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the users of mvpp2_bm_bufs_free() have been fixed, we can safely
clean the function prototype.
The function is always called to release all the buffers in a BM pool, and
the number of buffers freed is not needed. Therefore, we change the return
to a void, and remove the "num" parameter. This is a cosmetic change, to
make the code slightly cleaner.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a call to mvpp2_bm_bufs_free(), the caller usually wants to know
if the function successfully freed the requested number. However, this
cannot be done by looking into the BM pool count, because the current
buffer count was updated by mvpp2_bm_bufs_free().
In fact, the current callers of mvpp2_bm_bufs_free() use it to release
all the buffers in the pool, so we can fix this by simply checking
if the pool is not empty.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the network interfaces that are not configured by the bootloader
(using e.g. tftp or ping) can detect the link status but are unable to
transmit data.
The network controller has a functionality that allows the hardware to
continuously poll the PHY and directly update the MAC configuration accordingly
(speed, duplex, etc.). However, this doesn't work well with phylib's
software-based polling and updating MAC configuration in the driver's callback.
This commit fixes this issue by:
1. Setting MVPP2_PHY_AN_STOP_SMI0_MASK in MVPP2_PHY_AN_CFG0_REG in
mvpp2_init(), which disables the harware polling feature.
2. Disabling MVPP2_GMAC_PCS_ENABLE_MASK bit in MVPP2_GMAC_CTRL_2_REG in
mvpp2_port_mii_set() for port types other than SGMII.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit was originally wrong, the correct value is BIT(1), so fix it.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Null termination fix in dns_resolver got the pointer dereferncing
wrong, fix from Ben Hutchings.
2) ip_options_compile() has a benign but real buffer overflow when
parsing options. From Eric Dumazet.
3) Table updates can crash in netfilter's nftables if none of the state
flags indicate an actual change, from Pablo Neira Ayuso.
4) Fix race in nf_tables dumping, also from Pablo.
5) GRE-GRO support broke the forwarding path because the segmentation
state was not fully initialized in these paths, from Jerry Chu.
6) sunvnet driver leaks objects and potentially crashes on module
unload, from Sowmini Varadhan.
7) We can accidently generate the same handle for several u32
classifier filters, fix from Cong Wang.
8) Several edge case bug fixes in fragment handling in xen-netback,
from Zoltan Kiss.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
ipv4: fix buffer overflow in ip_options_compile()
batman-adv: fix TT VLAN inconsistency on VLAN re-add
batman-adv: drop QinQ claim frames in bridge loop avoidance
dns_resolver: Null-terminate the right string
xen-netback: Fix pointer incrementation to avoid incorrect logging
xen-netback: Fix releasing header slot on error path
xen-netback: Fix releasing frag_list skbs in error path
xen-netback: Fix handling frag_list on grant op error path
net_sched: avoid generating same handle for u32 filters
net: huawei_cdc_ncm: add "subclass 3" devices
net: qmi_wwan: add two Sierra Wireless/Netgear devices
wan/x25_asy: integer overflow in x25_asy_change_mtu()
net: ppp: fix creating PPP pass and active filters
net/mlx4_en: cq->irq_desc wasn't set in legacy EQ's
sunvnet: clean up objects created in vnet_new() on vnet_exit()
r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_40
net-gre-gro: Fix a bug that breaks the forwarding path
netfilter: nf_tables: 64bit stats need some extra synchronization
netfilter: nf_tables: set NLM_F_DUMP_INTR if netlink dumping is stale
netfilter: nf_tables: safe RCU iteration on list when dumping
...
This patch impliments ethtool_ops->get_rxnfc() to display the classifier
filter added by the driver.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the #ifdef CONFIG_RFS_ACCEL around the classifier filter
structures. This makes the filter structures available when CONFIG_RFS_ACCEL = n.
Introduce enic_rfs_timer_start() & enic_rfs_timer_stop() to start/stop the
timer. These two functions are nop when CONFIG_RFS_ACCEL = n.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link adjustment callback can be called as frequently as desired
by the PHY library, as such, let's avoid doing a Read/Modify/Write
sequence if nothing changed, since these register accesses can be
expensive.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that Wake-on-LAN support mode is fully integrated into the driver,
allow an user to query and configure Wake-on-LAN in the driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bcmgenet_suspend() to prepare the hardware for being put into
Wake-on-LAN mode if the device can wakeup the system, and Wake-on-LAN is
enabled. Whether we resume from Wake-on-LAN or not, make sure that
bcmgenet_resume() disables the UniMAC MagicPacket matching mode and puts
the hardware in a state where it can receive all incoming packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_wol_resume() will create an unbalanced clock state for the
wol_clk clock pointer since everywhere else in the code, we always call
clk_prepare_enable() and clk_disable_unprepare(). This function also
calls init_umac() which is neither correct nor necessary since
bcmgenet_resume() and bcmgenet_open() already does that.
Finally calling bcmgenet_wol_resume() in bcmgenet_open() is not correct,
since the interface would not have been able to put us in Wake-on-LAN
mode if it was not UP before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle UMAC_IRQ_MPD_R interrupt bit in our workqueue to make sure that
we properly re-configure the GENET adapter from Wake-on-LAN.
bcmgenet_power_up() makes sure that we will not leave the UniMAC
hardware in MagicPacket matching mode, since that would prevent any
other packet from being received.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bcmgenet_power_{up,down} to handle the case where the adapter has
been suspend respectively resumed from Wake-on-LAN using MagicPackets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add all the required code to program the GENET hardware to enter
Wake-on-LAN mode and wake using MagicPackets with or without SecureOn
password.
This code is hooked to the build system, but is not yet referenced from
ethtool or the main bcmgenet driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to the request the Wake-on-LAN interrupt bit, and if successful,
advertise wakeup capability instead of doing this unconditionnally.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement suspend/resume callbacks in the GENET driver. This makes sure
that we de-initialize and re-initialize the hardware correctly before
entering suspend and when resuming.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bunch of helper functions: bcmgenet_netif_start,
bcmgenet_netif_stop and bcmgenet_intr_disable to help reuse code that is
going to be necessary for suspend/resume.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the code touching the UniMAC RX/TX enable bits since we are going
to re-use it for implementing suspend/resume.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking for wol_enabled in bcmgenet_close() is bogus, since no other
code places set priv->wol_enabled. Remove that as it will conflict with
the upcoming and functional Wake-on-LAN implementation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENODEV from the no ports enabled error handling
case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement per channel software TX and RX packet counters
accessed as ethtool statistics.
This allows confirmation with MAC statistics.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver so far used adapter->num_vfs value to check if SR-IOV is enabled
or not. But, the patch bec84e6("create optimal number of queues on SR-IOV
config") changed this logic. The adapter->num_vfs value is validated and set
much before SR-IOV is enabled. So, we now use an explicit flag to track
SR-IOV enabled state.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As SRIOV is not supported on BE2 chip, avoid calling be_get/set_sriov_config()
for BE2 chip.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
max-vfs value must be accessed via the macro be_max_vfs(adapter).
The earlier patch "create optimal number of queues on SR-IOV config"
by mistake, did not use this macro. This patch fixes it.
fixes: bec84e6b ("be2net: create optimal number of queues on SR-IOV config")
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "if (foo == NULL)" statements with "if (!foo)" to be consistent
across the driver.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to adapter struct is passed anyway to all of the FW-cmd routines
in be_cmds.c. For routines which query data from FW, the adapter pointer
is enough to return the queried fields.
There is no need to separately pass pointers to individual members of
the adapter structure. This patch fixes this for be_cmd_get_fw_ver()
and be_cmd_get_fw_cfg() routines.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates some description strings for BEx/Skyhawk-R
UE (unrecoverable error) status register bits. The appropriate strings
are logged when a UE is detected in the adapter.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink layer expects a -ve status value to be returned when a driver
ndo method encounters an error. The driver was directly passing the
error status returned by FW (a positive value) to the stack.
This patch fixes this by returning -EIO status when a FW-cmd reports an error.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool expects a -ve status value to be returned when a driver method
encounters an error. The driver was directly passing the
error status returned by FW (a positive value) to ethtool.
This patch fixes this by returning -EIO status in cases where FW returns
an error.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FW stops responding with completions, return -ETIMEDOUT error
(instead of -1) to the stack.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For FW download ethtool cmd, if the user provides an FW-image incompatible
with the chip, return -EINVAL instead of -1.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating VF's tx-rate and FW-download are not allowed when the interface is
down. In such cases return -ENETDOWN to the stack.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This define is used by cxgb4i and iw_cxgb4, moving to avoid code duplication
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: fixed issue with checking return of dcbnl_rtnl_ops->getapp()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-07-16
This series contains updates to i40e only.
Neerav adds support to get the port MAC address from firmware and adds
support to the ndo_get_phys_port_id() callback to provide port specific
unique ids to the netdev layer.
Jakub Kicinski provides 2 fixes, first fixes i40e to never generate a software
time stamp if the hardware time stamp is provided. Second fixes a race
condition on queueing skb for hardware time by using a simple bit lock to
avoid race conditions and leaking skbs when multiple transmit rings try
to claim time stamping.
Paul does some general cleanup of the driver to remove unneeded spaces,
comments that are no longer valid, and break that will never get touched.
Jacob Keller adds a verbose warning message when the incorrect PF attempts
to control timestamping for a port to which it was not assigned. The primary
intent of this message is to help debugging the reason why the SIOCSHWSTAMP
ioctl has failed and to help narrow the cause of the issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to create PHYs from DT in case
if they are explicitly defined. The of_mdiobus_register() is
used for such purposes.
For backward compatibility, call of_mdiobus_register() only in case
if at least one PHY's child is defined in DT, otherwise rollback to
mdiobus_register().
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The similar MDIO HW blocks is used by keystone 2 SoCs as
in Davinci SoCs:
- one in Gigabit Ethernet (GbE) Switch Subsystem
See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
- one in 10 Gigabit Ethernet Subsystem
See http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
Hence, reuse Davinci MDIO driver for Keystone 2 and
enable TI networking for Keystone 2 devices
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a regression introduced by commit 35f6f45 ("net/mlx4_en: Don't use
irq_affinity_notifier to track changes in IRQ affinity map").
When core is started in legacy EQ's (number of IRQ's < rx rings), cq->irq_desc
was NULL. This caused a kernel crash under heavy traffic - when having more
than rx NAPI budget completions.
Fixed to have it set for both EQ modes.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In B0 steering mode if promiscuous QP asks to be detached from MCG entry,
and it is the only one in this entry then the entry will never be deleted.
This is a wrong behavior since we don't want to keep those entries after
the promiscuous QP becomes non-promiscuous. Therefore remove steering
entry containing only promiscuous QP.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current situation host is adding the promiscuous QP to all steering
entries and the default entry as well. In this case when having PV
and SR-IOV on the same setup bridge will receive all traffic that is
targeted to the other VMs. This is bad.
Solution: In SR-IOV mode host can add promiscuous QP to default entry only.
The above problem and fix are relevant for B0 steering mode only.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In B0 steering mode when adding QPs to the default MCG entry need
to check that maximal number of QPs per MCG entry was not exceeded.
Signed-off-by: Alexander Guller <alexg@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make sure that the array index isn't used in the code with
negative value, we stop using the for loop integer iterator
outside of it.
>From now on use members count to swap the last QP with removed one.
Fix also the second occurrence of this flow in mlx4_qp_detach_common().
In mlx4_qp_detach_common() use members_count instead of
loop iterator outside of the for loop.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing multicast address in B0 steering mode there is
a bug in cases where there is a single QP registered for the address,
and this QP is also promiscuous. In such cases the entry wouldn't be
deleted from the SW structure representing all Ethernet MCG entries,
but would be removed in HW. This way when driver goes to remove it
from SW and HW structures the HW deletion fails.
Moreover the same index could later be used for registering
different address, which can be Infiniband.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing cleans up the objects created by
vnet_new(), they are completely leaked.
vnet_exit(), after doing the vio_unregister_driver() to clean
up ports, should call a helper function that iterates over vnet_list
and cleans up those objects. This includes unregister_netdevice()
as well as free_netdev().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Reviewed-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet port on my ASUS A88X Pro mainboard stopped working
several times a day, with messages like these in dmesg:
AMD-Vi: Event logged [IO_PAGE_FAULT device=05:00.0 domain=0x001e address=0x0000000000003000 flags=0x0050]
Searching the web for these messages led me to similar reports about
different hardware supported by r8169, and eventually to commits
3ced8c955e ('r8169: enforce RX_MULTI_EN
for the 8168f.') and eb2dc35d99 ('r8169:
RxConfig hack for the 8168evl'). So I tried this change, and it fixes
the problem for me.
Signed-off-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display a verbose warning message when the incorrect PF attempts to
control timestamping for a port to which it was not assigned. This
shouldn't display except in the case of multiple PFs per port. The
primary intent of this message is to help debugging the reason why the
SIOCSHWTSTAMP ioctl has failed, and to help narrow the cause of the
issue.
Change-ID: Ic98798e0c844d98389d4c20e7160ba256f2bc7e8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove some break statements that will never get touched.
2. Remove an extra space.
3. Remove a comment for a parameter that doesn't exist
4. Move the assignment of a variable up to get rid of an else case.
Change-ID: I308a4b5ec070b1f0601f13b041ba4375aaad4b06
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.
Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new API to get the port mac address from firmware.
It also adds support to the ndo_get_phys_port_id() callback to provide
port specific unique id to the netdev layer.
If the adapter has a valid per-port mac address then that
would be used for this purpose and is expected to be unique
on a per-port basis.
The information can be viewed by reading the phys_port_id
attribute in sysfs for each netdev or via IF netlink
interface.
Change-ID: I341fa6fff9c112f1f6d987189309e730e0b50e8b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
instead of return error on zero rx_coalesce_usecs, disable coalesce
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a counter rx_noskb_drop for failure to allocate an skb.
Summed the per-channel rx_nodesc_trunc counters earlier so that they can
be included in rx_dropped.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of entries in the phy speed/duplex settings
array to support KR and KX mode, the work-around to add/remove
baseT settings to run at a fixed speed is no longer needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit enhances the iwarp driver to optionally keep a log of rdma
work request timining data for kernel mode QPs. If iw_cxgb4 module option
c4iw_wr_log is set to non-zero, each work request is tracked and timing
data maintained in a rolling log that is 4096 entries deep by default.
Module option c4iw_wr_log_size_order allows specifing a log2 size to use
instead of the default order of 12 (4096 entries). Both module options
are read-only and must be passed in at module load time to set them. IE:
modprobe iw_cxgb4 c4iw_wr_log=1 c4iw_wr_log_size_order=10
The timing data is viewable via the iw_cxgb4 debugfs file "wr_log".
Writing anything to this file will clear all the timing data.
Data tracked includes:
- The host time when the work request was posted, just before ringing
the doorbell. The host time when the completion was polled by the
application. This is also the time the log entry is created. The delta
of these two times is the amount of time took processing the work request.
- The qid of the EQ used to post the work request.
- The work request opcode.
- The cqe wr_id field. For sq completions requests this is the swsqe
index. For recv completions this is the MSN of the ingress SEND.
This value can be used to match log entries from this log with firmware
flowc event entries.
- The sge timestamp value just before ringing the doorbell when
posting, the sge timestamp value just after polling the completion,
and CQE.timestamp field from the completion itself. With these three
timestamps we can track the latency from post to poll, and the amount
of time the completion resided in the CQ before being reaped by the
application. With debug firmware, the sge timestamp is also logged by
firmware in its flowc history so that we can compute the latency from
posting the work request until the firmware sees it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ingress WRITE or READ RESPONSE errors, HW provides the offending
stag from the packet. This patch adds logic to log the parsed TPTE
in this case. cxgb4 now exports a function to read a TPTE entry
from adapter memory.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise a larger max read queue depth for qps, and gather the resource limits
from fw and use them to avoid exhaustinq all the resources.
Design:
cxgb4:
Obtain the max_ordird_qp and max_ird_adapter device params from FW
at init time and pass them up to the ULDs when they attach. If these
parameters are not available, due to older firmware, then hard-code
the values based on the known values for older firmware.
iw_cxgb4:
Fix the c4iw_query_device() to report these correct values based on
adapter parameters. ibv_query_device() will always return:
max_qp_rd_atom = max_qp_init_rd_atom = min(module_max, max_ordird_qp)
max_res_rd_atom = max_ird_adapter
Bump up the per qp max module option to 32, allowing it to be increased
by the user up to the device max of max_ordird_qp. 32 seems to be
sufficient to maximize throughput for streaming read benchmarks.
Fail connection setup if the negotiated IRD exhausts the available
adapter ird resources. So the driver will track the amount of ird
resource in use and not send an RI_WR/INIT to FW that would reduce the
available ird resources below zero.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates iw_cxgb4 to determine the Ingress Padding Boundary from
cxgb4_lld_info, and take subsequent actions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proper string for this license is "GPL v2", instead of "GPLv2".
This commit fixes that.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the 'foo*' bar with 'foo *bar' and (foo*) with (foo *).
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally any device ids will be above the corresponding device driver
structure. This patch moves the pci device ids and MODULE_DEVICE_TABLE()
above the pci driver structure.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert printk() to netdev_dbg/info/err or dev_info/err/dbg
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace ioremap() with the devm_ioremap() so that
the resource will be freed automatically with the probe failed.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the remove functionalities after the probe
so that we can see the registered and released resources properly.
Every driver follows the same concept.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to select 40G mode on a 10G/40G capable card.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi id was not marked for gro_skb, this will lead rx busy loop won't
work correctly since they stack never try to call low latency receive
method because of a zero socket napi id. Fix this by marking napi id
for gro_skb.
The transaction rate of 1 byte netperf tcp_rr gets about 50% increased
(from 20531.68 to 30610.88).
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_MODE_EN bit was defined to 0, while it is actually 6. It was not
much of a problem on older designs where this was a no-op, and the RGMII
data-path would always be enabled, but newer GENET controllers need to
explicitely enable their RGMII data-pad using this bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the IPv6 hw checksum for RTL8111C and later chips. Note
that the hw has the limitation for the transport offset. The
checksum must be calculated by sw, when the transport offset is
out of the range which the hw accepts.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace large send with giant send for TSO for RTL8111C and later ICs.
The large send setting of the RTL8111DP is different from the other
chips. However, the giant send setting is the same for all the chips
which support it. Use the giant send to synchronize the settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the txd_version, split rtl8169_tso_csum() into
rtl8169_tso_csum_v1() and rtl8169_tso_csum_v2().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a new network driver for the network controller in Marvell
Armada 375 SoC.
Given the controller is very different from the ones in the other Marvell
SoCs that use the mv643xx_eth (Kirkwood, Orion, Discovery) and mvneta
(Armada 370/38x/XP) drivers, a new driver is needed.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
[Ezequiel: coding style cleanup]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the debug message format. This patch changes to the
commit f160a2d0b524eeebd97a68e2fbb59fad4cdd3fee: net: cpmac: dynamic debug fixes
When we use pr_debug()/netdev_dbg() new lines are inserting in b/w
the values. The format when i use the printk()
These formats used in skb dump and reg dump. This functions
called from the entire code. So this will be enabled all the lines.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson