The RISC-V ISA defines a per-hart real-time clock and timer, which is
present on all systems. The clock is accessed via the 'rdtime'
pseudo-instruction (which reads a CSR), and the timer is set via an SBI
call.
Contains various improvements from Atish Patra <atish.patra@wdc.com>.
Signed-off-by: Dmitriy Cherkasov <dmitriy@oss-tech.org>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
[hch: remove dead code, add SPDX tags, used riscv_of_processor_hart(),
minor cleanups, merged hotplug cpu support and other improvements
from Atish]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
SPRD arch doesn't select SPRD_TIMER, so this config would not
appear even if ARCH_SPRD is set but COMPILE_TEST not.
Fix the dependency of this config with SPRD arch, and set a
default value for it, also leave other choices for EXPERT.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Pull missed timer updates from Thomas Gleixner:
"This is a branch which got forgotten during the merge window, but it
contains only fixes and hardware enablement. No fundamental changes.
- Various fixes for the imx-tpm clocksource driver
- A new timer driver for the NCPM7xx SoC family"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/imx-tpm: Add different counter width support
clocksource/drivers/imx-tpm: Correct some registers operation flow
clocksource/drivers/imx-tpm: Fix typo of clock name
dt-bindings: timer: tpm: fix typo of clock name
clocksource/drivers/npcm: Add NPCM7xx timer driver
dt-binding: timer: document NPCM7xx timer DT bindings
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
driver and timer driver), which has been through 7 rounds of review on mailing
list.
It is able to boot to shell and passes most LTP-2017 testsuites in nds32 AE3XX
platform.
Total Tests: 1901
Total Skipped Tests: 618
Total Failures: 78
Copied below is the ChangeLog that contains the history of this patch set:
Changes in v7:
- Update cpu binding document to add "andestech,nds32v3" as fallback
- Remove unnecessary configs of arch/nds32/Kconfig
- Use GENERIC_CALIBRATE_DELAY
- Add more help texts for minimum CPU type config
- Update defconfig because of Kconfig changed and bug fixed
- Move early_trap_init() declaration to nds32.h
- Refine dma.c
- Remove apply_relocate() in module.c and include <linux/moduleloader.h> to catch it
- Add do_kernel_restart() in machine_restart()
- Clean up setup.c to remove CONFIG_VGA_CONSOLE and some extern declaration functions
- Add negative dependency for VGA_CONSOLE on nds32
- Refine ptrace.c and arch/nds32/include/asm/ptrace.h
- Refine syscall restart flow and arch/nds32/kernel/signal.c
- Fix a bug in VDSO
- Remove the handling for kernel code unaligned accessing
- Add a description for unaligned access handling in git commit message.
- Rebase to v4.16-rc1
- Replace ACCESS_ONCE with READ_ONCE
- Replace atomic_long_dec(&mm->nr_ptes) with mm_dec_nr_ptes(mm)
- Remove print_symbol(%s) with printk(%pS)
- Add bpf_perf_event.h
- Remove init_stack and init_thread_info
Changes in v6:
- Refine naming for atl2c
- Refine ae3xx.dts
- Remove CONFIG_TIMER_ATCPIT100 in defconfig
- Refine elf.h
- Fix a vdso bug
- Separate arch patchset and timer patchset
- To select TIMER_OF in drivers/clocksource/Kconfig instead of arch/nds32/Kconfig
Changes in v5:
- Remove __NR__llseek and sys_mmap()
- Add a comment to explain that we don't have clocksource cycle counter in the CPU
- Add volatile in iounmap()
- Fix typo Featuretures to Features
- Replace CPU_CACHE_NONALIASING with !CPU_CACHE_ALIASING
- Fix a endian bug when we try to get val = of_get_property(cpu,"clock-frequency", NULL)
- Add screen_info to fix the building error when CONFIG_ VGA_CONSOLE is enabled
- Remove unnecessary msync()
- Add depends on !64BIT || BROKEN for faraday Kconfig because the descriptor only supports 32bit
- Add atl2c binding document
- Remove unnecessary include headers
- Fix a vector table bug. It placed wrong vector handlers for 2 exceptions.
- Fix a vdso bug. It may encounter TLB multi-hit exception because we accidently set it as a global page.
- Add proper isb and barrier after some cache operations
- Fix a bug in system call restart flow. $r0 ~ $r5 does not be recovered before restarting system call
- Fix the build errors for OpenRISC and SPARC because io.h changed.
- Update ae3xx.dts to support atl2c.
Changes in v4:
- Add atcpit100 timer driver due to it include vdso implementations and sent
them together with nds32 may help reviewer to review.
- Update ae3xx.dts for atcpit100 clock setting and remove vdso settings.
- To get cycle counter register by timer driver instead of dts.
- Use "depends on NDS32 || COMPILE_TEST" in atcpit100 driver because it is needed for nds32 vdso
- Update defconfig becasue kconfig rename from CONFIG_CLKSRC_ATCPIT100 to CONFIG_TIMER_ATCPIT100
- Remove ag101p.dts because we are not yet ready for ag101p platform.
- Update copyright style to SPDX-License-Identifier
- Include <linux/uaccess.h> instead of <asm/uaccess.h>
- Add local_irq_save()/local_irq_restore() to protect SR_TLB_VPN in update_mmu_cache().
- Update cpu_dcache_inval_all implementation to make sure all level cache are writeback.
Changes in v3:
- Use arch's io.h instead of generic one
- Add andestech-boards binding document
- Update nds32/cpus.txt binding document
- Remove atcpit100 timer drivers
- Select NO_BOOTMEM and delete HAVE_MEMBLOCK_NODE_MAP
- make CPU_BIG_ENDIAN and CPU_LITTLE_ENDIAN are dependent
- Add cpu type to select HWZOL/CPU_CACHE_ALIASING
- Change CPU_CACHE_NONALIASING to CPU_CACHE_ALIASING
- Remove bootarg from device tree script
- Update ag101p.dts and ae3xx.dts for correct board name.
- Clear and simplify defconfig
- Implement L2C_R_REG/ L2C_W_REG with readl/writel instead of __raw_readl/__raw_writel for endian save
- Remove early_init_dt_add_memory_arch/early_init_dt_alloc_memory_arch to use the generic ones
- Refine devicetree.c
- Fix bug https://lkml.kernel.org/r/1499782590-31366-1-git-send-ema...
- Refine irqchip/irq-ativic32.c implementations
- Add COMPILE_TEST in drivers/net/ethernet/faraday/Kconfig
- Refine cache operations
- Add CONFIG_HW_SUPPORT_UNALIGNMENT_ACCESS
- Fix ZERO_PAGE define
- Remove SA_RESTORER
- Remove uapi/asm/signal.h
- Redefine user_pt_regs
- Remove spinlock.h
- Remove __ARCH_WANT_RENAMEAT and __ARCH_WANT_SYSCALL_OFF_T from unistd.h
- Remove set_fs(USER_DS) because flush_old_exec() will do this setting
- Replace in_atomic() with faulthandler_disabled()
- Add barrier.h
- Select COMMON_CLK
- Add clk_pll in dts
- Add of_clk_init() in arch/nds32/kernel/time.c
Changes in v2:
- Set GENERIC_CALIBRATE_DELAY default n
- Add earlycon support
- Remove earlyprintk
- Add CPU_BIG_ENDIAN, CPU_LITTLE_ENDIAN support
- Refine unalignment access exception handler
- Add VMSPLIT support
- Use only one defconfig
- Change interrupt-cells from 2 to 1
- Refine andestech cpu names in bindings/nds32/cpus.txt
- Get clock frequency in dts because fpga bitmap doesn't include this feature
- Update MAINTAINERS for bindings
- Remove unused configs in Kconfig
- Refine device tree scripts
- Refine coding style
- Use generic ioremap_nocache
- Remove L2CC_PA_BASE define and its codes in head.S. It will be moved to bootloader.
- Set PHYS_OFFSET to 0x0 instead of CONFIG_MEMORY_START
- Remove unused macros
- Simplify cpu_cache_* API
- Change __asm__ __volatile__ to asm volatile
- Refine uaccess.h
- Remove unused/deprecated syscall
- Use generic posix_types.h
- Remove arch_trace_hardirqs_on/arch_trace_hardirqs_off
- Fix bug of restart syscall
- Refine syscall implementations
- Use IS_ENABLED to replace ifdef as possible
- Remove device_initcall(nds32_device_probe)
- Refine vdso implementations
- Refine copy_from_user()/copy_to_user()/clear_user()/get_user()/memmove()/memcpy()
- Refine ioremap.c
- Refine irq-ativic32.c
- Fix a bug of earlycon.c
- Export ioremap_nocache/ioremap_uc/ioremap_wc/ioremap_wt
- Add atcpit100 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=J/YF
-----END PGP SIGNATURE-----
Merge tag 'nds32-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux
Pull nds32 architecture support from Greentime Hu:
"This contains the core nds32 Linux port (including interrupt
controller driver and timer driver), which has been through seven
rounds of review on mailing list.
It is able to boot to shell and passes most LTP-2017 testsuites in
nds32 AE3XX platform:
Total Tests: 1901
Total Skipped Tests: 618
Total Failures: 78"
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
* tag 'nds32-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux: (44 commits)
nds32: To use the generic dump_stack()
nds32: fix building failed if using elf toolchain.
nios2: add ioremap_nocache declaration before include asm-generic/io.h.
nds32: fix building failed if using older version gcc.
dt-bindings: timer: Add andestech atcpit100 timer binding doc
clocksource/drivers/atcpit100: VDSO support
clocksource/drivers/atcpit100: Add andestech atcpit100 timer
net: faraday add nds32 support.
irqchip: Andestech Internal Vector Interrupt Controller driver
dt-bindings: interrupt-controller: Andestech Internal Vector Interrupt Controller
dt-bindings: nds32 SoC Bindings
dt-bindings: nds32 L2 cache controller Bindings
dt-bindings: nds32 CPU Bindings
MAINTAINERS: Add nds32
nds32: Build infrastructure
nds32: defconfig
nds32: Miscellaneous header files
nds32: Device tree support
nds32: Generic timers support
nds32: Loadable modules
...
The ATMEL_ST config selects MFD_SYSCON, but does not depend on HAS_IOMEM.
Compile testing on architecture without HAS_IOMEM causes "unmet direct
dependencies" in Kconfig phase. Detected by "make ARCH=score allyesconfig".
Add the proper dependency to the ATMEL_ST config.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1520335233-11277-1-git-send-email-yamada.masahiro@socionext.com
Now that arch/metag/ has been removed, remove the metag generic
per-thread timer driver. It is of no value without the architecture
code.
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-metag@vger.kernel.org
Move the dmtimer driver out of plat-omap to clocksource.
So that non-omap devices also could use this.
No Code changes done to the driver file only renamed to timer-ti-dm.c.
Also removed the config dependencies for OMAP_DM_TIMER.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
[tony@atomide.com: add select omap_dm_timer for omap16xx]
Signed-off-by: Tony Lindgren <tony@atomide.com>
ATCPIT100 is often used on the Andes architecture,
This timer provide 4 PIT channels. Each PIT channel is a
multi-function timer, can be configured as 32,16,8 bit timers
or PWM as well.
For system timer it will set channel 1 32-bit timer0 as clock
source and count downwards until underflow and restart again.
It also set channel 0 32-bit timer0 as clock event and count
downwards until condition match. It will generate an interrupt
for handling periodically.
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add andestech atcpit100 timer
Convert the driver to use the timer_of() helpers. This allows the removal of
a custom private structure, factors out and simplifies the code.
[Daniel Lezcano]: Respin against the critical fix patch and massaged the changelog.
Tested-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-12-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Spreadtrum SC9860 platform will use the architected timers as local
clock events, but we also need a broadcast timer device to wake up the
CPUs when the CPUs are in sleep mode.
The Spreadtrum timer can support 32-bit or 64-bit counters, as well as
supporting period mode or one-shot mode.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1515418139-23276-8-git-send-email-daniel.lezcano@linaro.org
[ Minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We regularly run into build errors when a clocksource driver selects
CONFIG_TIMER_OF while CONFIG_GENERIC_CLOCKEVENTS is disabled:
In file included from drivers/clocksource/timer-of.c:25:0:
drivers/clocksource/timer-of.h:35:28: error: field 'clkevt' has incomplete type
At the moment, three drivers can show this behavior: ARMV7M_SYSTICK,
CLKSRC_ST_LPC and CLKSRC_NPS. We could add further dependencies as we did
many times, but I have looked a little bit more at what architectures
are left that don't use GENERIC_CLOCKEVENTS, and this shows that there
is a better solution.
On arch/frv and arch/ia64, we never select CONFIG_GENERIC_CLOCKEVENTS
and we also don't use ARCH_USES_GETTIMEOFFSET, which would
block the clocksource Kconfig menu. On m68k, some platforms use
CONFIG_GENERIC_CLOCKEVENTS, some use ARCH_USES_GETTIMEOFFSET, and some
use neither of them. The good news is that there is no configuration that
does not set CONFIG_GENERIC_CLOCKEVENTS but that wants to enable any of
the Kconfig symbols in the menu, so we can simply replace the dependency
with the stricter one. While in theory one could have a clocksource
driver without the clockevent infrastructure, this seems unlikely
to be relevant in the future any more.
We can probably drop some of the other dependencies as well now,
e.g. there should generally be no reason to depend on CONFIG_ARM
unless the driver uses architecture specific assembly.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Pull timer fixes from Thomas Gleixner:
"A rather small update for the time(r) subsystem:
- A new clocksource driver IMX-TPM
- Minor fixes to the alarmtimer facility
- Device tree cleanups for Renesas drivers
- A new kselftest and fixes for the timer related tests
- Conversion of the clocksource drivers to use %pOF
- Use the proper helpers to access rlimits in the posix-cpu-timer
code"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Ensure RTC module is not unloaded
clocksource: Convert to using %pOF instead of full_name
clocksource/drivers/bcm2835: Remove message for a memory allocation failure
devicetree: bindings: Remove deprecated properties
devicetree: bindings: Remove unused 32-bit CMT bindings
devicetree: bindings: Deprecate property, update example
devicetree: bindings: r8a73a4 and R-Car Gen2 CMT bindings
devicetree: bindings: R-Car Gen2 CMT0 and CMT1 bindings
devicetree: bindings: Remove sh7372 CMT binding
clocksource/drivers/imx-tpm: Add imx tpm timer support
dt-bindings: timer: Add nxp tpm timer binding doc
posix-cpu-timers: Use dedicated helper to access rlimit values
alarmtimer: Fix unavailable wake-up source in sysfs
timekeeping: Use proper timekeeper for debug code
kselftests: timers: set-timer-lat: Add one-shot timer test cases
kselftests: timers: set-timer-lat: Tweak reporting when timer fires early
kselftests: timers: freq-step: Fix build warning
kselftests: timers: freq-step: Define ADJ_SETOFFSET if device has older kernel headers
IMX Timer/PWM Module (TPM) supports both timer and pwm function while
this patch only adds the timer support. PWM would be added later.
The TPM counter, compare and capture registers are clocked by an
asynchronous clock that can remain enabled in low power modes.
NOTE: We observed in a very small probability, the bus fabric
contention between GPU and A7 may results a few cycles delay
of writing CNT registers which may cause the min_delta event got
missed, so we need add a ETIME check here in case it happened.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In v4.13, CLKSRC_PISTACHIO can select TIMER_OF on architectures without
GENERIC_CLOCKEVENTS, resulting in a struct clock_event_device missing
some required features and build breakage compiling timer_of.c. One of
the symbols selecting TIMER_OF is CLKSRC_PISTACHIO, so add the
dependency on GENERIC_CLOCKEVENTS.
Thanks to kbuild test robot for finding this error
(https://lkml.org/lkml/2017/7/16/249)
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
- New SoC specific drivers
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
- Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini SoCs
- Various subsystem-wide cleanups
- Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA
data path acceleration that has previously been used on PowerPC
chips. I ended up postponing the merge until some API questions
for its unusual MMIO access are resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5L6n
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"New SoC specific drivers:
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini
SoCs
- Various subsystem-wide cleanups
Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA data
path acceleration that has previously been used on PowerPC chips. I
ended up postponing the merge until some API questions for its unusual
MMIO access are resolved"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
clocksource: owl: Add S900 support
clocksource: Add Owl timer
soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON
firmware: tegra: Fix locking bugs in BPMP
soc/tegra: flowctrl: Fix error handling
soc/tegra: bpmp: Implement generic PM domains
soc/tegra: bpmp: Update ABI header
PM / Domains: Allow overriding the ->xlate() callback
soc: brcmstb: enable drivers for ARM64 and BMIPS
soc: renesas: Rework Kconfig and Makefile logic
reset: Add the TI SCI reset driver
dt-bindings: reset: Add TI SCI reset binding
reset: use kref for reference counting
soc: qcom: smsm: Improve error handling, quiesce probe deferral
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
dt-bindings: reset: Add reset manager offsets for Stratix10
memory: omap-gpmc: add error message if bank-width property is absent
memory: omap-gpmc: make dts snippet include semicolon
reset: Add a Gemini reset controller
...
Previously a framework to factor out the drivers init function has been
merged.
Use this common framework in this driver, we get:
Before:
text data bss dec hex filename
1787 384 12 2183 887 drivers/clocksource/sun4i_timer.o
After:
text data bss dec hex filename
1407 512 0 1919 77f drivers/clocksource/sun4i_timer.o
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
The Actions Semi S500 SoC provides four timers, 2Hz0/1 and 32-bit TIMER0/1.
Use TIMER0 as clocksource and TIMER1 as clockevents.
Based on LeMaker linux-actions tree.
An S500 datasheet can be found on the LeMaker Guitar pages:
http://www.lemaker.org/product-guitar-download-29.html
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The different drivers are all using the same pattern when initializing.
1. Get the base address
2. Get the irq number
3. Get the clock
4. Prepare and enable the clock
5. Get the rate
6. Request an interrupt
Instead of repeating again and again these steps in all the drivers, let's
provide a common init routine to give the opportunity to factor all of them
out.
We can expect a significant kernel size improvement when the common routine
will be used in all the drivers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The config option name is now renamed to 'TIMER_ACPI' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The config option name is now renamed to 'TIMER_OF' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
After discussing it, this feature is dropped as it is not considered
adequate:
https://patchwork.kernel.org/patch/9639317/
There is no user of this macro yet, so there is no impact on the drivers.
This reverts commit 376bc27150.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This merges the Moxa Art timer driver into the Faraday FTTMR010
driver and replaces all Kconfig symbols to use the Faraday
driver instead. We are now so similar that the drivers can
be merged by just adding a few lines to the Faraday timer.
Differences:
- The Faraday driver explicitly sets the counter to count
upwards for the clocksource, removing the need for the
clocksource core to invert the value.
- The Faraday driver also handles sched_clock()
On the Aspeed, the counter can only count downwards, so support
the timers in downward-counting mode as well, and flag the
Aspeed to use this mode. This mode was tested on the Gemini so
I have high hopes that it'll work fine on the Aspeed as well.
After this we have one driver for all three SoCs and a generic
Faraday FTTMR010 timer driver, which is nice.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
that will also go via the arm64 tree.
-----BEGIN PGP SIGNATURE-----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=WlYI
-----END PGP SIGNATURE-----
Merge tag 'arch-timer-errata' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into clockevents/4.12
arm64 arch timer workaround series, including the base patches
that will also go via the arm64 tree.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
After some research it turns out that the "Gemini" timer is
actually a generic IP block from Faraday Technology named
FTTMR010, so as to not make things too confusing we need to
rename the driver and its symbols to make sense.
The implementation remains the same in this patch but we fix
the copy-paste error in the timer name "nomadik_mtu" as we're
at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The clock supplying the arm-global-timer on the rk3188 is coming from the
the cpu clock itself and thus changes its rate everytime cpufreq adjusts
the cpu frequency making this timer unsuitable as a stable clocksource
and sched clock.
The rk3188, rk3288 and following socs share a separate timer block already
handled by the rockchip-timer driver. Therefore adapt this driver to also
be able to act as clocksource and sched clock on rk3188.
In order to test clocksource you can run following commands and check
how much time it take in real. On rk3188 it take about ~45 seconds.
cpufreq-set -f 1.6GHZ
date; sleep 60; date
In order to use the patch you need to declare two timers in the dts
file. The first timer will be initialized as clockevent provider
and the second one as clocksource. The clockevent must be from
alive subsystem as it used as backup for the local timers at sleep
time.
The patch does not break compatibility with older device tree files.
The older device tree files contain only one timer. The timer
will be initialized as clockevent, as expected.
rk3288 (and probably anything newer) is irrelevant to this patch,
as it has the arch timer interface. This patch may be useful
for Cortex-A9/A5 based parts.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cortex-A73 (all versions) counter read can return a wrong value
when the counter crosses a 32bit boundary.
The workaround involves performing the read twice, and to return
one or the other depending on whether a transition has taken place.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Erratum Hisilicon-161010101 says that the ARM generic timer counter "has
the potential to contain an erroneous value when the timer value
changes". Accesses to TVAL (both read and write) are also affected due
to the implicit counter read. Accesses to CVAL are not affected.
The workaround is to reread the system count registers until the value
of the second read is larger than the first one by less than 32, the
system counter can be guaranteed not to return wrong value twice by
back-to-back read and the error value is always larger than the correct
one by 32. Writes to TVAL are replaced with an equivalent write to CVAL.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, fix Kconfig, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Currently we have code inline in the arch timer probe path to cater for
Freescale erratum A-008585, complete with ifdeffery. This is a little
ugly, and will get worse as we try to add more errata handling.
This patch refactors the handling of Freescale erratum A-008585. Now the
erratum is described in a generic arch_timer_erratum_workaround
structure, and the probe path can iterate over these to detect errata
and enable workarounds.
This will simplify the addition and maintenance of code handling
Hisilicon erratum 161010101.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
[Mark: split patch, correct Kconfig, reword commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch adds a OSTM driver for the Renesas architecture.
The OS Timer (OSTM) has independent channels that can be
used as a freerun or interval times.
This driver uses the first probed device as a clocksource
and then any additional devices as clock events.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This is a rewrite of the Gemini timer
driver in arch/arm/mach-gemini/timer.c trying to do everything
the device tree way:
- Make every IO-access relative to a base address and dynamic
so we can do a dynamic ioremap and get going.
- Do not poke around directly in the global syscon registers,
access them using the syscon regmap style design pattern for
the one register we need to check.
- Find register range and interrupt from the device tree.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The current code uses the CLOCKSOURCE_OF_DECLARE macro to fill the clksrc
table with a t-uple (name, init_function).
Unfortunately it ends up to the clockevent and the clocksource being
both initialized with this macro. It is not a problem by itself but there
is not a clear distinction between a clockevent and a clocksource in the
code initialization path. Somebody can argue there are the same IP block
and the same DT node. But conceptually from the software side, there are
two distincts entities and as is they should be initialized separetely.
Some drivers which do not have a clocksource end up by using the
CLOCKSOURCE_OF_DECLARE macro to declare a clockevent.
Another result is the fuzzy organization in the clocksource directory,
where the clockevents are implemented in the same file than the
clocksources or file labelled timer-something implementing a clocksource.
This patch provides another macro to specifically declare a clockevent in
the same way than the clocksource and gives the opportunity to write two
separate drivers, one for the clocksource and another for the clockevents.
Hopefully, that can help to do some housework in the directory, perhaps
split the drivers in to entities, for example:
- clksrc-rockchip.c
- clkevt-rockchip.c
Also, it gives the possibility to declare clocksources separately in the
DT and then use a clocksource from IP block while while clockevents are
used from another IP block.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds support for
- CONFIG_ARC_TIMERS : legacy 32-bit TIMER0 and TIMER1 which count UP
from @CNT to @LIMIT, before optionally triggering an interrupt.
These are programmed using ARC auxiliary register interface.
These are present in all ARC cores (ARC700 and ARC HS38)
TIMER0 serves as clockevent for all ARC linux builds.
TIMER1 is used for clocksource in arc700 builds.
- CONFIG_ARC_TIMERS_64BIT: 64-bit counters, RTC and GFRC found in
ARC HS38 cores. These are independnet IP blocks with different
programming model respectively.
Link: http://lkml.kernel.org/r/20161111231132.GA4186@mai
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
At the hardware level, the J-Core PIT is integrated with the interrupt
controller, but it is represented as its own device and has an
independent programming interface. It provides a 12-bit countdown
timer, which is not presently used, and a periodic timer. The interval
length for the latter is programmable via a 32-bit throttle register
whose units are determined by a bus-period register. The periodic
timer is used to implement both periodic and oneshot clock event
modes; in oneshot mode the interrupt handler simply disables the timer
as soon as it fires.
Despite its device tree node representing an interrupt for the PIT,
the actual irq generated is programmable, not hard-wired. The driver
is responsible for programming the PIT to generate the hardware irq
number that the DT assigns to it.
On SMP configurations, J-Core provides cpu-local instances of the PIT;
no broadcast timer is needed. This driver supports the creation of the
necessary per-cpu clock_event_device instances.
A nanosecond-resolution clocksource is provided using the J-Core "RTC"
registers, which give a 64-bit seconds count and 32-bit nanoseconds
that wrap every second. The driver converts these to a full-range
32-bit nanoseconds count.
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/b591ff12cc5ebf63d1edc98da26046f95a233814.1476393790.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Erratum A-008585 says that the ARM generic timer counter "has the
potential to contain an erroneous value for a small number of core
clock cycles every time the timer value changes". Accesses to TVAL
(both read and write) are also affected due to the implicit counter
read. Accesses to CVAL are not affected.
The workaround is to reread TVAL and count registers until successive
reads return the same value. Writes to TVAL are replaced with an
equivalent write to CVAL.
The workaround is to reread TVAL and count registers until successive reads
return the same value, and when writing TVAL to retry until counter
reads before and after the write return the same value.
The workaround is enabled if the fsl,erratum-a008585 property is found in
the timer node in the device tree. This can be overridden with the
clocksource.arm_arch_timer.fsl-a008585 boot parameter, which allows KVM
users to enable the workaround until a mechanism is implemented to
automatically communicate this information.
This erratum can be found on LS1043A and LS2080A.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Scott Wood <oss@buserror.net>
[will: renamed read macro to reflect that it's not usually unstable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch allows building and compile-testing the driver also for
ARM64. The delay_timer is only supported on ARMv7.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[k.kozlowski: Adjusted commit msg]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Disabling the eventstream can be useful for both remotely debugging a
deployed production system and development of code using WFE-based
polling loops. Whilst this can currently be controlled via a Kconfig
option (CONFIG_ARM_ARCH_TIMER_EVTSTREAM), it's often desirable to toggle
the feature on the command line, so this patch adds a new command-line
option ("clocksource.arm_arch_timer.evtstrm") to do just that. The
default behaviour is determined based on CONFIG_ARM_ARCH_TIMER_EVTSTREAM.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach,
allowing the user to compile the driver on different platforms.
The current option let the user to select the clocksource or not.
The Kconfig option policy is to let the platform to select the
timer automatically.
Add the COMPILE_TEST option, so the prompt to select the driver will
be showed only when COMPILE_TEST is set and will let this driver
to compile on different platform, thus increasing the compilation
test coverage.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach,
allowing the user to compile the driver on different platforms.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach,
allowing the user to compile the driver on different platforms.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_INTEGRATOR_AP_TIMER and is selected
by the platform. Then the clocksource's Kconfig is changed to make this
option selectable by the user if the COMPILE_TEST option is set. Otherwise,
it is up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_KEYSTONE_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_NSPIRE_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_U300_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Due on the delay specific code, this driver will compile only on the ARM
architecture.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_PRIMA2_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_MXS_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Change the Kconfig option logic to fullfil with the current approach.
A new Kconfig option is added, CONFIG_MOXART_TIMER and is selected by the
platform. Then the clocksource's Kconfig is changed to make this option
selectable by the user if the COMPILE_TEST option is set. Otherwise, it is
up to the platform's Kconfig to select the timer.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Palmer Dabbelt