commit 34e526cb7d46726b2ae5f83f2892d00ebb088509 upstream.
Even though the boot protocol stipulates otherwise, an exception has
been made for the EFI stub, and entering the core kernel with the MMU
enabled is permitted. This allows a substantial amount of cache
maintenance to be elided, wich is significant when fast boot times are
critical (e.g., for booting micro-VMs)
Once the initial ID map has been populated, the MMU is disabled as part
of the logic sequence that puts all system registers into a known state.
Any code that needs to execute within the window where the MMU is off is
cleaned to the PoC explicitly, which includes all of HYP text when
entering at EL2.
However, the current sequence of initializing the EL2 system registers
is not safe: HCR_EL2 is set to its nVHE initial state before SCTLR_EL2
is reprogrammed, and this means that a VHE-to-nVHE switch may occur
while the MMU is enabled. This switch causes some system registers as
well as page table descriptors to be interpreted in a different way,
potentially resulting in spurious exceptions relating to MMU
translation.
So disable the MMU explicitly first when entering in EL2 with the MMU
and caches enabled.
Fixes: 6178617038 ("efi: arm64: enter with MMU and caches enabled")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: <stable@vger.kernel.org> # 6.3.x
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240415075412.2347624-6-ardb+git@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2673dfb591a359c75080dd5af3da484b89320d22 upstream.
Check kvm_mmu_page_ad_need_write_protect() when deciding whether to
write-protect or clear D-bits on TDP MMU SPTEs, so that the TDP MMU
accounts for any role-specific reasons for disabling D-bit dirty logging.
Specifically, TDP MMU SPTEs must be write-protected when the TDP MMU is
being used to run an L2 (i.e. L1 has disabled EPT) and PML is enabled.
KVM always disables PML when running L2, even when L1 and L2 GPAs are in
the some domain, so failing to write-protect TDP MMU SPTEs will cause
writes made by L2 to not be reflected in the dirty log.
Reported-by: syzbot+900d58a45dcaab9e4821@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=900d58a45dcaab9e4821
Fixes: 5982a53926 ("KVM: x86/mmu: Use kvm_ad_enabled() to determine if TDP MMU SPTEs need wrprot")
Cc: stable@vger.kernel.org
Cc: Vipin Sharma <vipinsh@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Signed-off-by: David Matlack <dmatlack@google.com>
Link: https://lore.kernel.org/r/20240315230541.1635322-2-dmatlack@google.com
[sean: massage shortlog and changelog, tweak ternary op formatting]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49ff3b4aec51e3abfc9369997cc603319b02af9a upstream.
On AMD and Hygon platforms, the local APIC does not automatically set
the mask bit of the LVTPC register when handling a PMI and there is
no need to clear it in the kernel's PMI handler.
For guests, the mask bit is currently set by kvm_apic_local_deliver()
and unless it is cleared by the guest kernel's PMI handler, PMIs stop
arriving and break use-cases like sampling with perf record.
This does not affect non-PerfMonV2 guests because PMIs are handled in
the guest kernel by x86_pmu_handle_irq() which always clears the LVTPC
mask bit irrespective of the vendor.
Before:
$ perf record -e cycles:u true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data (1 samples) ]
After:
$ perf record -e cycles:u true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB perf.data (19 samples) ]
Fixes: a16eb25b09 ("KVM: x86: Mask LVTPC when handling a PMI")
Cc: stable@vger.kernel.org
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
[sean: use is_intel_compatible instead of !is_amd_or_hygon()]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240405235603.1173076-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e985cbf2942a1bb8fcef9adc2a17d90fd7ca8ee upstream.
Drop support for virtualizing adaptive PEBS, as KVM's implementation is
architecturally broken without an obvious/easy path forward, and because
exposing adaptive PEBS can leak host LBRs to the guest, i.e. can leak
host kernel addresses to the guest.
Bug #1 is that KVM doesn't account for the upper 32 bits of
IA32_FIXED_CTR_CTRL when (re)programming fixed counters, e.g
fixed_ctrl_field() drops the upper bits, reprogram_fixed_counters()
stores local variables as u8s and truncates the upper bits too, etc.
Bug #2 is that, because KVM _always_ sets precise_ip to a non-zero value
for PEBS events, perf will _always_ generate an adaptive record, even if
the guest requested a basic record. Note, KVM will also enable adaptive
PEBS in individual *counter*, even if adaptive PEBS isn't exposed to the
guest, but this is benign as MSR_PEBS_DATA_CFG is guaranteed to be zero,
i.e. the guest will only ever see Basic records.
Bug #3 is in perf. intel_pmu_disable_fixed() doesn't clear the upper
bits either, i.e. leaves ICL_FIXED_0_ADAPTIVE set, and
intel_pmu_enable_fixed() effectively doesn't clear ICL_FIXED_0_ADAPTIVE
either. I.e. perf _always_ enables ADAPTIVE counters, regardless of what
KVM requests.
Bug #4 is that adaptive PEBS *might* effectively bypass event filters set
by the host, as "Updated Memory Access Info Group" records information
that might be disallowed by userspace via KVM_SET_PMU_EVENT_FILTER.
Bug #5 is that KVM doesn't ensure LBR MSRs hold guest values (or at least
zeros) when entering a vCPU with adaptive PEBS, which allows the guest
to read host LBRs, i.e. host RIPs/addresses, by enabling "LBR Entries"
records.
Disable adaptive PEBS support as an immediate fix due to the severity of
the LBR leak in particular, and because fixing all of the bugs will be
non-trivial, e.g. not suitable for backporting to stable kernels.
Note! This will break live migration, but trying to make KVM play nice
with live migration would be quite complicated, wouldn't be guaranteed to
work (i.e. KVM might still kill/confuse the guest), and it's not clear
that there are any publicly available VMMs that support adaptive PEBS,
let alone live migrate VMs that support adaptive PEBS, e.g. QEMU doesn't
support PEBS in any capacity.
Link: https://lore.kernel.org/all/20240306230153.786365-1-seanjc@google.com
Link: https://lore.kernel.org/all/ZeepGjHCeSfadANM@google.com
Fixes: c59a1f106f ("KVM: x86/pmu: Add IA32_PEBS_ENABLE MSR emulation for extended PEBS")
Cc: stable@vger.kernel.org
Cc: Like Xu <like.xu.linux@gmail.com>
Cc: Mingwei Zhang <mizhang@google.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhang Xiong <xiong.y.zhang@intel.com>
Cc: Lv Zhiyuan <zhiyuan.lv@intel.com>
Cc: Dapeng Mi <dapeng1.mi@intel.com>
Cc: Jim Mattson <jmattson@google.com>
Acked-by: Like Xu <likexu@tencent.com>
Link: https://lore.kernel.org/r/20240307005833.827147-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd706c9b1674e2858766bfbf7430534c2b26fbef upstream.
Add kvm_vcpu_arch.is_amd_compatible to cache if a vCPU's vendor model is
compatible with AMD, i.e. if the vCPU vendor is AMD or Hygon, along with
helpers to check if a vCPU is compatible AMD vs. Intel. To handle Intel
vs. AMD behavior related to masking the LVTPC entry, KVM will need to
check for vendor compatibility on every PMI injection, i.e. querying for
AMD will soon be a moderately hot path.
Note! This subtly (or maybe not-so-subtly) makes "Intel compatible" KVM's
default behavior, both if userspace omits (or never sets) CPUID 0x0 and if
userspace sets a completely unknown vendor. One could argue that KVM
should treat such vCPUs as not being compatible with Intel *or* AMD, but
that would add useless complexity to KVM.
KVM needs to do *something* in the face of vendor specific behavior, and
so unless KVM conjured up a magic third option, choosing to treat unknown
vendors as neither Intel nor AMD means that checks on AMD compatibility
would yield Intel behavior, and checks for Intel compatibility would yield
AMD behavior. And that's far worse as it would effectively yield random
behavior depending on whether KVM checked for AMD vs. Intel vs. !AMD vs.
!Intel. And practically speaking, all x86 CPUs follow either Intel or AMD
architecture, i.e. "supporting" an unknown third architecture adds no
value.
Deliberately don't convert any of the existing guest_cpuid_is_intel()
checks, as the Intel side of things is messier due to some flows explicitly
checking for exactly vendor==Intel, versus some flows assuming anything
that isn't "AMD compatible" gets Intel behavior. The Intel code will be
cleaned up in the future.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240405235603.1173076-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe90f3967bdb3e13f133e5f44025e15f943a99c5 upstream.
Many architectures' switch_mm() (e.g. arm64) do not have an smp_mb()
which the core scheduler code has depended upon since commit:
commit 223baf9d17 ("sched: Fix performance regression introduced by mm_cid")
If switch_mm() doesn't call smp_mb(), sched_mm_cid_remote_clear() can
unset the actively used cid when it fails to observe active task after it
sets lazy_put.
There *is* a memory barrier between storing to rq->curr and _return to
userspace_ (as required by membarrier), but the rseq mm_cid has stricter
requirements: the barrier needs to be issued between store to rq->curr
and switch_mm_cid(), which happens earlier than:
- spin_unlock(),
- switch_to().
So it's fine when the architecture switch_mm() happens to have that
barrier already, but less so when the architecture only provides the
full barrier in switch_to() or spin_unlock().
It is a bug in the rseq switch_mm_cid() implementation. All architectures
that don't have memory barriers in switch_mm(), but rather have the full
barrier either in finish_lock_switch() or switch_to() have them too late
for the needs of switch_mm_cid().
Introduce a new smp_mb__after_switch_mm(), defined as smp_mb() in the
generic barrier.h header, and use it in switch_mm_cid() for scheduler
transitions where switch_mm() is expected to provide a memory barrier.
Architectures can override smp_mb__after_switch_mm() if their
switch_mm() implementation provides an implicit memory barrier.
Override it with a no-op on x86 which implicitly provide this memory
barrier by writing to CR3.
Fixes: 223baf9d17 ("sched: Fix performance regression introduced by mm_cid")
Reported-by: levi.yun <yeoreum.yun@arm.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> # for arm64
Acked-by: Dave Hansen <dave.hansen@linux.intel.com> # for x86
Cc: <stable@vger.kernel.org> # 6.4.x
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240415152114.59122-2-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a90bca2228c0646fc29a72689d308e5fe03e6d78 upstream.
The sysfs_break_active_protection() routine has an obvious reference
leak in its error path. If the call to kernfs_find_and_get() fails then
kn will be NULL, so the companion sysfs_unbreak_active_protection()
routine won't get called (and would only cause an access violation by
trying to dereference kn->parent if it was called). As a result, the
reference to kobj acquired at the start of the function will never be
released.
Fix the leak by adding an explicit kobject_put() call when kn is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 2afc9166f7 ("scsi: sysfs: Introduce sysfs_{un,}break_active_protection()")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/8a4d3f0f-c5e3-4b70-a188-0ca433f9e6f9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8d2f34ea96ea3bce6ba2535f867f0d4ee3b22e1 upstream.
In case a console is set up really large and contains a really long word
(> 256 characters), we have to stop before the length of the word buffer.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Fixes: c6e3fd22cd ("Staging: add speakup to the staging directory")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240323164843.1426997-1-samuel.thibault@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dc04112bee6fdd6eb847ccb32214703022c0269 upstream.
Extend the quirk to disable MEI interface on Intel PCH Ignition (IGN)
and SPS firmwares for RPL-S devices. These firmwares do not support
the MEI protocol.
Fixes: 3ed8c7d39c ("mei: me: add raptor lake point S DID")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240312051958.118478-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6334b8e4553cc69f51e383c9de545082213d785e upstream.
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240327023550.51214-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d920a2ed8620be04a3301e1a9c2b7cc1de65f19d upstream.
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1607830dadeefc407e4956336d9fcd9e9defd810 upstream.
This reverts commit 339f83612f3a569b194680768b22bf113c26a29d.
It has been found to cause problems in a number of Chromebook devices,
so revert the change until it can be brought back in a safe way.
Link: https://lore.kernel.org/r/385a3519-b45d-48c5-a6fd-a3fdb6bec92f@chromium.org
Reported-by:: Aleksander Morgado <aleksandermj@chromium.org>
Fixes: 339f83612f3a ("usb: cdc-wdm: close race between read and workqueue")
Cc: stable <stable@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1aa4ad4eb695bac1b0a7ba542a16d6833c9c8dd8 upstream.
We are seeing start_tx being called after port shutdown as noted by Jiri.
This happens because we are missing the startup and shutdown related
functions for the serial base port.
Let's fix the issue by adding startup and shutdown functions for the
serial base port to block tx flushing for the serial base port when the
port is not in use.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240411055848.38190-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cf7ea2eeb745213dc2a04103e426b960e807940 upstream.
The circular buffer is NULLified in uart_tty_port_shutdown()
under the spin lock. However, the PM or other timer based callbacks
may still trigger after this event without knowning that buffer pointer
is not valid. Since the serial code is a bit inconsistent in checking
the buffer state (some rely on the head-tail positions, some on the
buffer pointer), it's better to have both aligned, i.e. buffer pointer
to be NULL and head-tail possitions to be the same, meaning it's empty.
This will prevent asynchronous calls to dereference NULL pointer as
reported recently in 8250 case:
BUG: kernel NULL pointer dereference, address: 00000cf5
Workqueue: pm pm_runtime_work
EIP: serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
...
? serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
__start_tx (drivers/tty/serial/8250/8250_port.c:1551)
serial8250_start_tx (drivers/tty/serial/8250/8250_port.c:1654)
serial_port_runtime_suspend (include/linux/serial_core.h:667 drivers/tty/serial/serial_port.c:63)
__rpm_callback (drivers/base/power/runtime.c:393)
? serial_port_remove (drivers/tty/serial/serial_port.c:50)
rpm_suspend (drivers/base/power/runtime.c:447)
The proposed change will prevent ->start_tx() to be called during
suspend on shut down port.
Fixes: 43066e32227e ("serial: port: Don't suspend if the port is still busy")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202404031607.2e92eebe-lkp@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240404150034.41648-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea2624b5b829b8f93c0dce25721d835969b34faf upstream.
When an UART is opened that still has .throttled set from a previous
open, the RX interrupt is enabled but the irq handler doesn't consider
it. This easily results in a stuck irq with the effect to occupy the CPU
in a tight loop.
So reset the throttle state in .startup() to ensure that RX irqs are
handled.
Fixes: d1ec8a2eab ("serial: stm32: update throttle and unthrottle ops for dma mode")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/a784f80d3414f7db723b2ec66efc56e1ad666cbf.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13c785323b36b845300b256d0e5963c3727667d7 upstream.
If there is a stuck irq that the handler doesn't address, returning
IRQ_HANDLED unconditionally makes it impossible for the irq core to
detect the problem and disable the irq. So only return IRQ_HANDLED if
an event was handled.
A stuck irq is still problematic, but with this change at least it only
makes the UART nonfunctional instead of occupying the (usually only) CPU
by 100% and so stall the whole machine.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5f92603d0dfd8a5b8014b2b10a902d91e0bb881f.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1be3226445362bfbf461c92a5bcdb1723f2e4907 upstream.
The mitigation was intended to stop the irq completely. That may be
better than a hard lock-up but it turns out that you get a crash anyway
if you're using pmac_zilog as a serial console:
ttyPZ0: pmz: rx irq flood !
BUG: spinlock recursion on CPU#0, swapper/0
That's because the pr_err() call in pmz_receive_chars() results in
pmz_console_write() attempting to lock a spinlock already locked in
pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal
BUG splat. The spinlock in question is the one in struct uart_port.
Even when it's not fatal, the serial port rx function ceases to work.
Also, the iteration limit doesn't play nicely with QEMU, as can be
seen in the bug report linked below.
A web search for other reports of the error message "pmz: rx irq flood"
didn't produce anything. So I don't think this code is needed any more.
Remove it.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@kernel.org
Cc: linux-m68k@lists.linux-m68k.org
Link: https://github.com/vivier/qemu-m68k/issues/44
Link: https://lore.kernel.org/all/1078874617.9746.36.camel@gaston/
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/e853cf2c762f23101cd2ddec0cc0c2be0e72685f.1712568223.git.fthain@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54c4ec5f8c471b7c1137a1f769648549c423c026 upstream.
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147e ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1718530e3f640b7d5f0050e725216eab57a85d8 upstream.
While vmk80xx does have endpoint checking implemented, some things
can fall through the cracks. Depending on the hardware model,
URBs can have either bulk or interrupt type, and current version
of vmk80xx_find_usb_endpoints() function does not take that fully
into account. While this warning does not seem to be too harmful,
at the very least it will crash systems with 'panic_on_warn' set on
them.
Fix the issue found by Syzkaller [1] by somewhat simplifying the
endpoint checking process with usb_find_common_endpoints() and
ensuring that only expected endpoint types are present.
This patch has not been tested on real hardware.
[1] Syzkaller report:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 781 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
Call Trace:
<TASK>
usb_start_wait_urb+0x113/0x520 drivers/usb/core/message.c:59
vmk80xx_reset_device drivers/comedi/drivers/vmk80xx.c:227 [inline]
vmk80xx_auto_attach+0xa1c/0x1a40 drivers/comedi/drivers/vmk80xx.c:818
comedi_auto_config+0x238/0x380 drivers/comedi/drivers.c:1067
usb_probe_interface+0x5cd/0xb00 drivers/usb/core/driver.c:399
...
Similar issue also found by Syzkaller:
Link: https://syzkaller.appspot.com/bug?extid=5205eb2f17de3e01946e
Reported-and-tested-by: syzbot+5f29dc6a889fc42bd896@syzkaller.appspotmail.com
Cc: stable <stable@kernel.org>
Fixes: 49253d542c ("staging: comedi: vmk80xx: factor out usb endpoint detection")
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20240408171633.31649-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c38fa07dc69f0b9e6f43ecab96dc7861a70c827c upstream.
Currently we don't configure correctly the wake events after unplug of device
router. What can happen is that the downstream ports of host router will be
configured to wake on: USB4-wake and wake-on-disconnect, but not on
wake-on-connect. This may cause the later plugged device not to wake the
domain and fail in enumeration. Fix this by clearing downstream port's "USB4
Port is Configured" bit, after unplug of a device router.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcd12acaf384c30437fa5a9a1f71df06fc9835fd upstream.
Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).
While there add the missing kernel-doc for tb_switch_resume().
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaef73821a3b0194a01bd23ca77774f704a04d40 upstream.
Commit 6d98eb95b4 ("binder: avoid potential data leakage when copying
txn") introduced changes to how binder objects are copied. In doing so,
it unintentionally removed an offset alignment check done through calls
to binder_alloc_copy_from_buffer() -> check_buffer().
These calls were replaced in binder_get_object() with copy_from_user(),
so now an explicit offset alignment check is needed here. This avoids
later complications when unwinding the objects gets harder.
It is worth noting this check existed prior to commit 7a67a39320
("binder: add function to copy binder object from buffer"), likely
removed due to redundancy at the time.
Fixes: 6d98eb95b4 ("binder: avoid potential data leakage when copying txn")
Cc: stable@vger.kernel.org
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20240330190115.1877819-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ee5faad0f8c3ad86c8cfc2f6aac91d2ba29790f upstream.
The Haier Boyue G42 with ALC269VC cannot detect the MIC of headset,
the line out and internal speaker until
ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS quirk applied.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Cc: <stable@vger.kernel.org>
Message-ID: <20240419082159.476879-1-aichao@kylinos.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7caf3daaaf0436fe370834c72c667a97d3671d1a upstream.
The headset mic requires a fixup to be properly detected/used.
As a reference, this specific model from 2021 reports
the following devices:
https://alsa-project.org/db/?f=1a5ddeb0b151db8fe051407f5bb1c075b7dd3e4a
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <stable@vger.kernel.org>
Message-ID: <b92a9e49fb504eec8416bcc6882a52de89450102.1713370457.git.mchehab@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f25f17dc5c6a5e3f2014d44635f0c0db45224efe upstream.
The conversion from MIDI2 to MIDI1 UMP messages had a leftover
artifact (superfluous bit shift), and this resulted in the bogus type
check, leading to empty outputs. Let's fix it.
Fixes: e9e02819a9 ("ALSA: seq: Automatic conversion of UMP events")
Cc: <stable@vger.kernel.org>
Link: https://github.com/alsa-project/alsa-utils/issues/262
Message-ID: <20240419100442.14806-1-tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0553e753ea9ee724acaf6b3dfc7354702af83567 ]
Next patch will move devlink register to be first. Therefore, whenever
mlx5 will register a param, the user will be notified.
In order to notify the user, devlink is using the get() callback of
the param. Hence, resources that are being used by the get() callback
must be set before the devlink param is registered.
Therefore, store eswitch pointer inside mdev before registering the
param.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9543f6e26634537997b6e909c20911b7bf4876de ]
Fix cpuid_deps[] to list the correct dependencies for GFNI, VAES, and
VPCLMULQDQ. These features don't depend on AVX512, and there exist CPUs
that support these features but not AVX512. GFNI actually doesn't even
depend on AVX.
This prevents GFNI from being unnecessarily disabled if AVX is disabled
to mitigate the GDS vulnerability.
This also prevents all three features from being unnecessarily disabled
if AVX512VL (or its dependency AVX512F) were to be disabled, but it
looks like there isn't any case where this happens anyway.
Fixes: c128dbfa0f ("x86/cpufeatures: Enable new SSE/AVX/AVX512 CPU features")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20240417060434.47101-1-ebiggers@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69129794d94c544810e68b2b4eaa7e44063f9bf2 ]
Confusingly, X86_FEATURE_RETPOLINE doesn't mean retpolines are enabled,
as it also includes the original "AMD retpoline" which isn't a retpoline
at all.
Also replace cpu_feature_enabled() with boot_cpu_has() because this is
before alternatives are patched and cpu_feature_enabled()'s fallback
path is slower than plain old boot_cpu_has().
Fixes: ec9404e40e8f ("x86/bhi: Add BHI mitigation knob")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/ad3807424a3953f0323c011a643405619f2a4927.1712944776.git.jpoimboe@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f7b1d8b5505efb0057cd1ab85fca206063ea4c3 ]
mt8183-mfgcfg has a mutual dependency with genpd during the probing
stage, which leads to a deadlock in the following call stack:
CPU0: genpd_lock --> clk_prepare_lock
genpd_power_off_work_fn()
genpd_lock()
generic_pm_domain::power_off()
clk_unprepare()
clk_prepare_lock()
CPU1: clk_prepare_lock --> genpd_lock
clk_register()
__clk_core_init()
clk_prepare_lock()
clk_pm_runtime_get()
genpd_lock()
Do a runtime PM get at the probe function to make sure clk_register()
won't acquire the genpd lock. Instead of only modifying mt8183-mfgcfg,
do this on all mediatek clock controller probings because we don't
believe this would cause any regression.
Verified on MT8183 and MT8192 Chromebooks.
Fixes: acddfc2c26 ("clk: mediatek: Add MT8183 clock support")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240312115249.3341654-1-treapking@chromium.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d1e795f754db1ac3344528b7af0b17b8146f321 ]
Similar to the previous commit, we should make sure that all devices are
runtime resumed before printing the clk_summary through debugfs. Failure
to do so would result in a deadlock if the thread is resuming a device
to print clk state and that device is also runtime resuming in another
thread, e.g the screen is turning on and the display driver is starting
up. We remove the calls to clk_pm_runtime_{get,put}() in this path
because they're superfluous now that we know the devices are runtime
resumed. This also squashes a bug where the return value of
clk_pm_runtime_get() wasn't checked, leading to an RPM count underflow
on error paths.
Fixes: 1bb294a798 ("clk: Enable/Disable runtime PM for clk_summary")
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-6-sboyd@kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e581cf5d216289ef292d1a4036d53ce90e122469 ]
Doug reported [1] the following hung task:
INFO: task swapper/0:1 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00000008
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
rpm_resume+0xe0/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
clk_pm_runtime_get+0x30/0xb0
clk_disable_unused_subtree+0x58/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused_subtree+0x38/0x208
clk_disable_unused+0x4c/0xe4
do_one_initcall+0xcc/0x2d8
do_initcall_level+0xa4/0x148
do_initcalls+0x5c/0x9c
do_basic_setup+0x24/0x30
kernel_init_freeable+0xec/0x164
kernel_init+0x28/0x120
ret_from_fork+0x10/0x20
INFO: task kworker/u16:0:9 blocked for more than 122 seconds.
Not tainted 5.15.149-21875-gf795ebc40eb8 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack: 0 pid: 9 ppid: 2 flags:0x00000008
Workqueue: events_unbound deferred_probe_work_func
Call trace:
__switch_to+0xf4/0x1f4
__schedule+0x418/0xb80
schedule+0x5c/0x10c
schedule_preempt_disabled+0x2c/0x48
__mutex_lock+0x238/0x488
__mutex_lock_slowpath+0x1c/0x28
mutex_lock+0x50/0x74
clk_prepare_lock+0x7c/0x9c
clk_core_prepare_lock+0x20/0x44
clk_prepare+0x24/0x30
clk_bulk_prepare+0x40/0xb0
mdss_runtime_resume+0x54/0x1c8
pm_generic_runtime_resume+0x30/0x44
__genpd_runtime_resume+0x68/0x7c
genpd_runtime_resume+0x108/0x1f4
__rpm_callback+0x84/0x144
rpm_callback+0x30/0x88
rpm_resume+0x1f4/0x52c
rpm_resume+0x178/0x52c
__pm_runtime_resume+0x58/0x98
__device_attach+0xe0/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
device_add+0x644/0x814
mipi_dsi_device_register_full+0xe4/0x170
devm_mipi_dsi_device_register_full+0x28/0x70
ti_sn_bridge_probe+0x1dc/0x2c0
auxiliary_bus_probe+0x4c/0x94
really_probe+0xcc/0x2c8
__driver_probe_device+0xa8/0x130
driver_probe_device+0x48/0x110
__device_attach_driver+0xa4/0xcc
bus_for_each_drv+0x8c/0xd8
__device_attach+0xf8/0x170
device_initial_probe+0x1c/0x28
bus_probe_device+0x3c/0x9c
deferred_probe_work_func+0x9c/0xd8
process_one_work+0x148/0x518
worker_thread+0x138/0x350
kthread+0x138/0x1e0
ret_from_fork+0x10/0x20
The first thread is walking the clk tree and calling
clk_pm_runtime_get() to power on devices required to read the clk
hardware via struct clk_ops::is_enabled(). This thread holds the clk
prepare_lock, and is trying to runtime PM resume a device, when it finds
that the device is in the process of resuming so the thread schedule()s
away waiting for the device to finish resuming before continuing. The
second thread is runtime PM resuming the same device, but the runtime
resume callback is calling clk_prepare(), trying to grab the
prepare_lock waiting on the first thread.
This is a classic ABBA deadlock. To properly fix the deadlock, we must
never runtime PM resume or suspend a device with the clk prepare_lock
held. Actually doing that is near impossible today because the global
prepare_lock would have to be dropped in the middle of the tree, the
device runtime PM resumed/suspended, and then the prepare_lock grabbed
again to ensure consistency of the clk tree topology. If anything
changes with the clk tree in the meantime, we've lost and will need to
start the operation all over again.
Luckily, most of the time we're simply incrementing or decrementing the
runtime PM count on an active device, so we don't have the chance to
schedule away with the prepare_lock held. Let's fix this immediate
problem that can be triggered more easily by simply booting on Qualcomm
sc7180.
Introduce a list of clk_core structures that have been registered, or
are in the process of being registered, that require runtime PM to
operate. Iterate this list and call clk_pm_runtime_get() on each of them
without holding the prepare_lock during clk_disable_unused(). This way
we can be certain that the runtime PM state of the devices will be
active and resumed so we can't schedule away while walking the clk tree
with the prepare_lock held. Similarly, call clk_pm_runtime_put() without
the prepare_lock held to properly drop the runtime PM reference. We
remove the calls to clk_pm_runtime_{get,put}() in this path because
they're superfluous now that we know the devices are runtime resumed.
Reported-by: Douglas Anderson <dianders@chromium.org>
Closes: https://lore.kernel.org/all/20220922084322.RFC.2.I375b6b9e0a0a5348962f004beb3dafee6a12dfbb@changeid/ [1]
Closes: https://issuetracker.google.com/328070191
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9a34b45397 ("clk: Add support for runtime PM")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-5-sboyd@kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d05ae531c2cff20d5d527f04e28d28e04379929 ]
Initialize this kref once we allocate memory for the struct clk_core so
that we can reuse the release function to free any memory associated
with the structure. This mostly consolidates code, but also clarifies
that the kref lifetime exists once the container structure (struct
clk_core) is allocated instead of leaving it in a half-baked state for
most of __clk_core_init().
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-4-sboyd@kernel.org
Stable-dep-of: e581cf5d2162 ("clk: Get runtime PM before walking tree during disable_unused")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8358a76cfb47c9a5af627a0c4e7168aa14fa25f6 ]
Removing this assertion lets us move the kref_put() call outside the
prepare_lock section. We don't need to hold the prepare_lock here to
free memory and destroy the clk_core structure. We've already unlinked
the clk from the clk tree and by the time the release function runs
nothing holds a reference to the clk_core anymore so anything with the
pointer can't access the memory that's being freed anyway. Way back in
commit 496eadf821 ("clk: Use lockdep asserts to find missing hold of
prepare_lock") we didn't need to have this assertion either.
Fixes: 496eadf821 ("clk: Use lockdep asserts to find missing hold of prepare_lock")
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240325184204.745706-2-sboyd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de1bf25b6d771abdb52d43546cf57ad775fb68a1 ]
The icc_lock mutex was split into separate icc_lock and icc_bw_lock
mutexes in [1] to avoid lockdep splats. However, this didn't adequately
protect access to icc_node::req_list.
The icc_set_bw() function will eventually iterate over req_list while
only holding icc_bw_lock, but req_list can be modified while only
holding icc_lock. This causes races between icc_set_bw(), of_icc_get(),
and icc_put().
Example A:
CPU0 CPU1
---- ----
icc_set_bw(path_a)
mutex_lock(&icc_bw_lock);
icc_put(path_b)
mutex_lock(&icc_lock);
aggregate_requests()
hlist_for_each_entry(r, ...
hlist_del(...
<r = invalid pointer>
Example B:
CPU0 CPU1
---- ----
icc_set_bw(path_a)
mutex_lock(&icc_bw_lock);
path_b = of_icc_get()
of_icc_get_by_index()
mutex_lock(&icc_lock);
path_find()
path_init()
aggregate_requests()
hlist_for_each_entry(r, ...
hlist_add_head(...
<r = invalid pointer>
Fix this by ensuring icc_bw_lock is always held before manipulating
icc_node::req_list. The additional places icc_bw_lock is held don't
perform any memory allocations, so we should still be safe from the
original lockdep splats that motivated the separate locks.
[1] commit af42269c35 ("interconnect: Fix locking for runpm vs reclaim")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Fixes: af42269c35 ("interconnect: Fix locking for runpm vs reclaim")
Reviewed-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20240305225652.22872-1-quic_mdtipton@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f609e7b1b49e4d15cf107d2069673ee63860c398 ]
BIOS 03.05 still hasn't fixed the spurious IRQ1 issue. As it's still
being worked on there is still a possibility that it won't need to
apply to future BIOS releases.
Add a quirk for BIOS 03.05 as well.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240410141046.433-1-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a1ccf0c72cf917ff3ccc131d1bb8d19338ffe52 ]
This patch introduces a new USB quirk,
USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value
for the SET_ADDRESS request. The standard timeout for USB request/command
is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1).
However, certain scenarios, such as connecting devices through an APTIV
hub, can lead to timeout errors when the device enumerates as full speed
initially and later switches to high speed during chirp negotiation.
In such cases, USB analyzer logs reveal that the bus suspends for
5 seconds due to incorrect chirp parsing and resumes only after two
consecutive timeout errors trigger a hub driver reset.
Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us)
_______| Time Stamp(28 . 105 910 682)
_______|_____________________________________________________________Ch0
Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us)
_______| Time Stamp(28 . 106 910 632)
_______|_____________________________________________________________Ch0
Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us)
_______| Time Stamp(28 . 107 910 600)
_______|_____________________________________________________________Ch0
Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms)
_______| Time Stamp(28 . 108 532 832)
_______|_____________________________________________________________Ch0
Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us)
_______| Time Stamp(28 . 247 657 600)
_______|_____________________________________________________________Ch0
This 5-second delay in device enumeration is undesirable, particularly
in automotive applications where quick enumeration is crucial
(ideally within 3 seconds).
The newly introduced quirks provide the flexibility to align with a
3-second time limit, as required in specific contexts like automotive
applications.
By reducing the SET_ADDRESS request timeout to 500 ms, the
system can respond more swiftly to errors, initiate rapid recovery, and
ensure efficient device enumeration. This change is vital for scenarios
where rapid smartphone enumeration and screen projection are essential.
To use the quirk, please write "vendor_id:product_id:p" to
/sys/bus/usb/drivers/hub/module/parameter/quirks
For example,
echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks"
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a769154c7cac037914ba375ae88aae55b2c853e0 ]
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 5a1ccf0c72cf ("usb: new quirk to reduce the SET_ADDRESS request timeout")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 430143b0d3611f4a9c8434319e5e504244749e79 ]
The Legion Go has a 2560x1600 portrait screen, with the native "up" facing
the right controller (90° CW from the rest of the device).
Signed-off-by: Brenton Simpson <appsforartists@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231114233859.274189-1-appsforartists@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efc3d7d20361cc59325a9f0525e079333b4459c0 ]
This driver was originally developed for the Focusrite Scarlett Gen 2
series. Since then Focusrite have used a similar protocol for their
Gen 3, Gen 4, Clarett USB, Clarett+, and Vocaster series.
Let's call this common protocol the "Scarlett 2 Protocol" and rename
the driver to scarlett2 to not imply that it is restricted to Gen 2
series devices.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/e1ad7f69a1e20cdb39094164504389160c1a0a0b.1698342632.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ard Biesheuvel