Unlike gen11, which always ran at 50MHz when the cdclk PLL was disabled,
TGL runs at refclk/2. The 50MHz croclk/2 is only used by hardware
during some power state transitions.
Bspec: 49201
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190905181337.23727-1-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The bspec was recently updated with these new cdclk values for ICL, EHL,
and TGL.
Bspec: 20598
Bspec: 49201
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826225540.11987-3-matthew.d.roper@intel.com
The bspec has just recently been updated with new cdclk values that
require the use of a /2 CD2X divider rather than a /1 divider. Once we
add the divider selection logic to ICL+ cdclk programming, we have
pretty much the same logic we were already using on CNL, so it's simpler
to drop icl_set_cdclk() completely and reuse cnl_set_cdclk() on gen11+
platforms as well.
v2:
- Using ICL_CDCLK_CD2X_PIPE_NONE + BXT_CDCLK_CD2X_PIPE(pipe) for TGL is
correct, but looks really confusing. Add some TGL_ macros that alias
these to avoid confusion. (Ville)
- Use DIV_ROUND_CLOSEST rather than / when applying the divider. (Ville)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830004828.19359-1-matthew.d.roper@intel.com
We may need to eliminate the crtc->index == pipe assumptions from
the code to support arbitrary pipes being fused off. Start that by
switching some bitmasks over to using pipe instead of the crtc index.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821173033.24123-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
To reduce the number of explicit dev_priv->uncore calls in the display
code ahead of the introduction of dev_priv->de_uncore, this patch
introduces a wrapper for one of the main usages of it, the register
waits. When we transition to the new uncore, we can just update the
wrapper to point to the appropriate structure.
Since the vast majority of waits are on a set or clear of a bit or mask,
add set & clear flavours of the wrapper to simplify the code.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816012343.36433-7-daniele.ceraolospurio@intel.com
Everything about the file is about display, and mostly about types
related to display. Move under display/ as intel_display_types.h to
reflect the facts.
There's still plenty to clean up, but start off with moving the file
where it logically belongs and naming according to contents.
v2: fix the include guard name in the renamed file
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113933.11799-1-jani.nikula@intel.com
On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
Cc: stable@vger.kernel.org
Tested-by: Stefan Gottwald <gottwald@igel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111149
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717114536.22937-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
The PFI credit programming performed during cdclk change on vlv/chv
requires access to a register in the disp2d power well. So far
we've abused pipe-A power domain for this, but now we have the
more appropriate "display core" domain so let's make use of it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190701161534.6671-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
EHL has it own voltage level requirement depending on cd clock.
BSpec: 21809
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626014053.30541-3-jose.souza@intel.com
EHL do not support 648 and 652.8 MHz.
v2:
- Limiting maximum CD clock by max_cdclk_freq instead of remove it
from icl_calc_cdclk()(Ville and Jani)
BSpec: 20598
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626014053.30541-2-jose.souza@intel.com
Now 180, 172.8 and 192 MHz are supported.
180 and 172.8 MHz CD clocks will only be used when audio is not
enabled as state by BSpec and implemented in
intel_crtc_compute_min_cdclk(), CD clock must be at least twice of
Azalia BCLK and BCLK by default is 96 MHz, it could be set to 48 MHz
but we are not reading it.
v3:
- making icl clock arrays static (Ville)
BSpec: 20598
BSpec: 15729
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626014053.30541-1-jose.souza@intel.com
Now that we have a new subdirectory for display code, continue by moving
modesetting core code.
display/intel_frontbuffer.h sticks out like a sore thumb, otherwise this
is, again, a surprisingly clean operation.
v2:
- don't move intel_sideband.[ch] (Ville)
- use tabs for Makefile file lists and sort them
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-3-jani.nikula@intel.com
Matt Roper