The s3c24xx platform was removed and this driver is no longer
needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221021203329.4143397-14-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current kernel DMA with PASID support is based on the SVA with a flag
SVM_FLAG_SUPERVISOR_MODE. The IOMMU driver binds the kernel memory address
space to a PASID of the device. The device driver programs the device with
kernel virtual address (KVA) for DMA access. There have been security and
functional issues with this approach:
- The lack of IOTLB synchronization upon kernel page table updates.
(vmalloc, module/BPF loading, CONFIG_DEBUG_PAGEALLOC etc.)
- Other than slight more protection, using kernel virtual address (KVA)
has little advantage over physical address. There are also no use
cases yet where DMA engines need kernel virtual addresses for in-kernel
DMA.
This removes SVM_FLAG_SUPERVISOR_MODE support from the IOMMU interface.
The device drivers are suggested to handle kernel DMA with PASID through
the kernel DMA APIs.
The drvdata parameter in iommu_sva_bind_device() and all callbacks is not
needed anymore. Cleanup them as well.
Link: https://lore.kernel.org/linux-iommu/20210511194726.GP1002214@nvidia.com/
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Tony Zhu <tony.zhu@intel.com>
Link: https://lore.kernel.org/r/20221031005917.45690-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The iop32x platform was removed, so this driver is no longer
needed.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20221019150410.3851944-10-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There's a previously unknown part of the controller interface: We have
to assign SRAM carveouts to channels to store their in-flight samples
in. So, obtain the size of the SRAM from a read-only register and divide
it into 2K blocks for allocation to channels. The FIFO depths we
configure will always fit into 2K.
(This fixes audio artifacts during simultaneous playback/capture on
multiple channels -- which looking back is fully accounted for by having
had the caches in the DMA controller overlap in memory.)
Fixes: b127315d9a ("dmaengine: apple-admac: Add Apple ADMAC driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221019132324.8585-2-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In current code, dev.max_batch_size and wq.max_batch_size attributes in
sysfs are exposed to user to show or update the values.
>From Intel IAA spec [1], Intel IAA does not support batch processing. So
these sysfs attributes should not be supported on IAA device.
Fix this issue by making the attributes of max_batch_size invisible in
sysfs through is_visible() filter when the device is IAA.
Add description in the ABI documentation to mention that the attributes
are not visible when the device does not support batch.
[1]: https://cdrdv2.intel.com/v1/dl/getContent/721858
Fixes: e7184b159d ("dmaengine: idxd: add support for configurable max wq batch size")
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220930201528.18621-3-xiaochen.shen@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The function idma64_remove() returns zero unconditionally. Make it
return void.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221014161250.468687-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4755 has 4 DMA channels per DMA unit, two idential DMA units.
The JZ4755 has the similar DMA engine to JZ4725b and it has the
same bug as JZ4725b, see commit a40c94be23.
At least the JZ_SOC_DATA_BREAK_LINKS flag make it work much better,
although not ideal.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Siarhei Volkau <lis8215@gmail.com>
Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
Link: https://lore.kernel.org/r/20221019063934.3278444-3-lis8215@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the idxd_user_drv driver is bound to a Work Queue (WQ) device
without IOMMU or with IOMMU Passthrough without Shared Virtual
Addressing (SVA), the application gains direct access to physical
memory via the device by programming physical address to a submitted
descriptor. This allows direct userspace read and write access to
arbitrary physical memory. This is inconsistent with the security
goals of a good kernel API.
Unlike vfio_pci driver, the IDXD char device driver does not provide any
ways to pin user pages and translate the address from user VA to IOVA or
PA without IOMMU SVA. Therefore the application has no way to instruct the
device to perform DMA function. This makes the char device not usable for
normal application usage.
Since user type WQ without SVA cannot be used for normal application usage
and presents the security issue, bind idxd_user_drv driver and enable user
type WQ only when SVA is enabled (i.e. user PASID is enabled).
Fixes: 448c3de8ac ("dmaengine: idxd: create user driver for wq 'device'")
Cc: stable@vger.kernel.org
Suggested-by: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20221014222541.3912195-1-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New bool m2m_hw has been added at the end of stm32_mdma_chan_config struct
to support the STM32 DMA MDMA chaining.
m2m_hw is set true in stm32_mdma_slave_config() if peripheral_size is set,
but m2m_hw is never initialized false.
To ensure this case, and any further new update of the structure, memset it
to 0 before using it.
Fixes: 6968743227 ("dmaengine: stm32-mdma: add support to be triggered by STM32 DMA")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20221017131413.202567-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Combine all the SoC specific files into a single lib that can be
built-in or built as a module.
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220929234820.940048-4-khilman@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently k3-udma driver is built as separate platform drivers with a
shared probe and identical code path, just differnet platform data.
To enable to build as module, convert the separate platform driver
into a single module_platform_driver with the data selection done via
compatible string and of_match. The separate of_match tables are also
combined into a single table to avoid the multiple calls to
of_match_node()
Since all modern TI platforms using this are DT enabled, the removal
of separate platform_drivers should have no functional change.
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220929234820.940048-3-khilman@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Devices with ee offset of 0x10000 should rather bind with SM6350
compatible, so the list will not unnecessarily grow for compatible
devices.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20221018230352.1238479-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The drivers are transitioning from matching against lists of specific
compatible strings to matching against smaller lists of more generic
compatible strings. Add a message that the compatible strings with an
ee_offset of 0 are deprecated except for the SDM845 compatible string.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221018005740.23952-4-mailingradian@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The prandom_bytes() function has been a deprecated inline wrapper around
get_random_bytes() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. This was done as a basic find and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> # powerpc
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
New Support:
- AngeloGioacchino Del Regno added support for MT6795 SoC dma controller
- Christian Marangi updated qcom-adm controller binding to yaml
- Geert Uytterhoeven added yaml binding for Renesas r8a779g0 dma controller
- Luca Weiss added support for Qualcomm SM6350 GPI dma controller
Updates:
- Amelie Delaunay provided STM32 DMA-MDMA chaining support
- Andy Shevchenko updated hsu driver to use managed resources
- Dave Jiang & Jerry Snitselaar provided usual round of idxd driver updates
- Janne Grunau & Martin Povišer updated apple dma driver for iommu and pd
properties and removed use of devres for irqs
- Swati Agarwal added device_synchronize support for Xilinx zynqmp driver
-----BEGIN PGP SIGNATURE-----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=zRon
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New Support:
- MT6795 SoC dma controller (AngeloGioacchino Del Regno)
- qcom-adm controller yaml binding (Christian Marangi)
- Renesas r8a779g0 dma controller yaml binding (Geert Uytterhoeven)
- Qualcomm SM6350 GPI dma controller (Luca Weiss)
Updates:
- STM32 DMA-MDMA chaining support (Amelie Delaunay)
- make hsu driver use managed resources (Andy Shevchenko)
- the usual round of idxd driver updates (Dave Jiang & Jerry
Snitselaar)
- apple dma driver iommu and pd properties and remove use
of devres for irqs (Janne Grunau & Martin Povišer)
- device_synchronize support for Xilinx zynqmp driver (Swati
Agarwal)"
* tag 'dmaengine-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (60 commits)
dmaengine: ioat: remove unused declarations in dma.h
dmaengine: ti: k3-udma: Respond TX done if DMA_PREP_INTERRUPT is not requested
dmaengine: zynqmp_dma: Add device_synchronize support
dt-bindings: dma: add additional pbus reset to qcom,adm
dt-bindings: dma: rework qcom,adm Documentation to yaml schema
dt-bindings: dma: apple,admac: Add iommus and power-domains properties
dmaengine: dw-edma: Remove runtime PM support
dmaengine: idxd: add configuration for concurrent batch descriptor processing
dmaengine: idxd: add configuration for concurrent work descriptor processing
dmaengine: idxd: add WQ operation cap restriction support
dmanegine: idxd: reformat opcap output to match bitmap_parse() input
dmaengine: idxd: convert ats_dis to a wq flag
dmaengine: ioat: stop mod_timer from resurrecting deleted timer in __cleanup()
dmaengine: qcom-adm: fix wrong calling convention for prep_slave_sg
dmaengine: qcom-adm: fix wrong sizeof config in slave_config
dmaengine: ti: k3-psil: add additional TX threads for j721e
dmaengine: ti: k3-psil: add additional TX threads for j7200
dmaengine: apple-admac: Trigger shared reset
dmaengine: apple-admac: Do not use devres for IRQs
dmaengine: ti: edma: Remove some unused functions
...
ioat_ring_alloc_order and ioat_ring_max_alloc_order have
been removed since commit cd60cd9613 ("dmaengine: IOATDMA:
Removing descriptor ring reshape"), so remove them.
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20220911091817.3214271-1-cuigaosheng1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the DMA consumer driver does not expect the callback for TX done, then
we need not perform the channel RT byte counter calculations and estimate
the completion but return complete on first attempt itself.This assumes
that the consumer who did not request DMA_PREP_INTERRUPT has its own
mechanism for understanding TX completion, example: MCSPI EOW interrupt
can be used as TX completion signal for a SPI transaction.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220914110049.5842-1-vaishnav.a@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dmaengine_synchronize implementation is required to synchronize proper
termination of current transfers so that any memory resources are not freed
while still in use.
Implement this callback in the driver so that framework can use the same
(in dmaengine_terminate_sync/ dmaengine_synchronize).
Signed-off-by: Swati Agarwal <swati.agarwal@amd.com>
Link: https://lore.kernel.org/r/20220915090516.5812-1-swati.agarwal@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, the dw-edma driver enables the runtime_pm for parent device
(chip->dev) and increments/decrements the refcount during alloc/free
chan resources callbacks.
This leads to a problem when the eDMA driver has been probed, but the
channels were not used. This scenario can happen when the DW PCIe driver
probes eDMA driver successfully, but the PCI EPF driver decides not to
use eDMA channels and use iATU instead for PCI transfers.
In this case, the underlying device would be runtime suspended due to
pm_runtime_enable() in dw_edma_probe() and the PCI EPF driver would have
no knowledge of it.
Ideally, the eDMA driver should not be the one doing the runtime PM of
the parent device. The responsibility should instead belong to the client
drivers like PCI EPF.
So let's remove the runtime PM support from eDMA driver.
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20220910054700.12205-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add sysfs knob to allow control of the number of batch descriptors that can
be concurrently processed by an engine in the group as a fraction of the
Maximum Work Descriptors in Progress value specfied in ENGCAP register.
This control knob is part of toggle for QoS control.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220917161222.2835172-6-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add sysfs knob to allow control of the number of work descriptors that can
be concurrently processed by an engine in the group as a fraction of the
Maximum Work Descriptors in Progress value specified in ENGCAP register.
This control knob is part of toggle for QoS control.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220917161222.2835172-5-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DSA 2.0 add the capability of configuring DMA ops on a per workqueue basis.
This means that certain ops can be disabled by the system administrator for
certain wq. By default, all ops are available. A bitmap is used to store
the ops due to total op size of 256 bits and it is more convenient to use a
range list to specify which bits are enabled.
One of the usage to support this is for VM migration between different
iteration of devices. The newer ops are disabled in order to allow guest to
migrate to a host that only support older ops. Another usage is to
restrict the WQ to certain operations for QoS of performance.
A sysfs of ops_config attribute is added per wq. It is only usable when the
ops_config bit is set under WQ_CAP register. This means that this attribute
will return -EOPNOTSUPP on DSA 1.x devices. The expected input is a range
list for the bits per operation the WQ supports.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220917161222.2835172-4-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To make input and output consistent and prepping for the per WQ operation
configuration support, change the output of opcap display to match the
input that is expected by bitmap_parse() helper function. The output will
be a bitmap with field width as the number of bits using the %*pb format
specifier for printk() family.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220917161222.2835172-3-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
User reports observing timer event report channel halted but no error
observed in CHANERR register. The driver finished self-test and released
channel resources. Debug shows that __cleanup() can call
mod_timer() after the timer has been deleted and thus resurrect the
timer. While harmless, it causes suprious error message to be emitted.
Use mod_timer_pending() call to prevent deleted timer from being
resurrected.
Fixes: 3372de5813 ("dmaengine: ioatdma: removal of dma_v3.c and relevant ioat3 references")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/166360672197.3851724.17040290563764838369.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The calling convention for pre_slave_sg is to return NULL on error and
provide an error log to the system. Qcom-adm instead provide error
pointer when an error occur. This indirectly cause kernel panic for
example for the nandc driver that checks only if the pointer returned by
device_prep_slave_sg is not NULL. Returning an error pointer makes nandc
think the device_prep_slave_sg function correctly completed and makes
the kernel panics later in the code.
While nandc is the one that makes the kernel crash, it was pointed out
that the real problem is qcom-adm not following calling convention for
that function.
To fix this, drop returning error pointer and return NULL with an error
log.
Fixes: 03de6b2738 ("dmaengine: qcom-adm: stop abusing slave_id config")
Fixes: 5c9f8c2dbd ("dmaengine: qcom: Add ADM driver")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.11+
Link: https://lore.kernel.org/r/20220916041256.7104-1-ansuelsmth@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix broken slave_config function that uncorrectly compare the
peripheral_size with the size of the config pointer instead of the size
of the config struct. This cause the crci value to be ignored and cause
a kernel panic on any slave that use adm driver.
To fix this, compare to the size of the struct and NOT the size of the
pointer.
Fixes: 03de6b2738 ("dmaengine: qcom-adm: stop abusing slave_id config")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org # v5.17+
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220915204844.3838-1-ansuelsmth@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If a reset domain is attached to the device, obtain a shared reference
to it and trigger it. Typically on a chip the ADMAC controller will
share a reset domain with the MCA peripheral.
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220918095845.68860-5-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is in advance of adding support for triggering the reset signal to
the peripheral, since registering the IRQ handler will have to be
sequenced with it.
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220918095845.68860-4-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
These functions are defined in the edma.c file, but not called elsewhere,
so delete these unused functions.
drivers/dma/ti/edma.c:746:31: warning: unused function 'to_edma_cc'.
drivers/dma/ti/edma.c:420:20: warning: unused function 'edma_param_or'.
drivers/dma/ti/edma.c:414:20: warning: unused function 'edma_param_and'.
drivers/dma/ti/edma.c:402:20: warning: unused function 'edma_param_write'.
drivers/dma/ti/edma.c:373:28: warning: unused function 'edma_shadow0_read'.
drivers/dma/ti/edma.c:396:28: warning: unused function 'edma_param_read'.
drivers/dma/ti/edma.c:355:20: warning: unused function 'edma_or_array'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2152
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220914101943.83929-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since fault processing code has been removed, struct idxd_fault is not used any
more and can be removed as well.
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20220928014747.106808-1-yuancan@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that idxd_wq_disable_cleanup() sets the workqueue state to
IDXD_WQ_DISABLED, use a bitmap to track which workqueues have been
enabled. This will then be used to determine which workqueues
should be re-enabled when attempting a software reset to recover
from a device halt state.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20220928154856.623545-3-jsnitsel@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If we are calling idxd_wq_disable_cleanup(), the workqueue should be
in a disabled state. So set the workqueue state to IDXD_WQ_DISABLED so
that the state reflects that. Currently if there is a device failure,
and a software reset is attempted the workqueues will not be
re-enabled due to idxd_wq_enable() seeing that state as already being
IDXD_WQ_ENABLED.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20220928154856.623545-2-jsnitsel@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver registration fails on SOC imx8mn as its supplier, the clock
control module, is probed later than subsys initcall level. This driver
uses platform_driver_probe which is not compatible with deferred probing
and won't be probed again later if probe function fails due to clock not
being available at that time.
This patch replaces the use of platform_driver_probe with
platform_driver_register which will allow probing the driver later again
when the clock control module will be available.
The __init annotation has been dropped because it is not compatible with
deferred probing. The code is not executed once and its memory cannot be
freed.
Fixes: a580b8c542 ("dmaengine: mxs-dma: add dma support for i.MX23/28")
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220921170556.1055962-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220803223448.6f08095b@endymion.delvare
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a cosmetic change and replace two if statements with a single if
statement with two conditions. In case the optional txstate parameter is
NULL, we return the dma_cookie_status, which is fine, no functional change
required.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220802140630.243550-1-tudor.ambarus@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should call of_node_put() for the reference returned by
of_parse_phandle() in fail path or when it is not used anymore.
Here we only need to move the of_node_put() before the check.
Fixes: d702419134 ("dmaengine: ti: k3-udma: Add glue layer for non DMAengine users")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220720073234.1255474-1-windhl@126.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32_DMAMUX_MAX_DMA_REQUESTS is small (i.e. 32) and when the 'dma_inuse'
bitmap is allocated, there is already a check that 'dma_req' is <= this
limit.
So, there is no good reason to dynamically allocate this bitmap. This
just waste some memory and some cycles.
Use DECLARE_BITMAP with the maximum bitmap size instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/2d8c24359b2daa32ce0597a2949b7b2bebaf23de.1659211633.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
>From the coccinelle check:
./drivers/dma/sf-pdma/sf-pdma.c
Error:line 409 is redundant because platform_get_irq() already prints an
error
./drivers/dma/sf-pdma/sf-pdma.c
Error:line 424 is redundant because platform_get_irq() already prints an
error
So,remove the unnecessary print function dev_err()
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220810062532.13425-1-ye.xingchen@zte.com.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
UDMA_CHAN_RT_*BCNT_REG stores the real-time channel bytecount statistics.
These registers are 32-bit hardware counters and the driver uses these
counters to monitor the operational progress status for a channel, when
transferring more than 4GB of data it was observed that these counters
overflow and completion calculation of a operation gets affected and the
transfer hangs indefinitely.
This commit adds changes to decrease the byte count for every complete
transaction so that these registers never overflow and the proper byte
count statistics is maintained for ongoing transaction by the RT counters.
Earlier uc->bcnt used to maintain a count of the completed bytes at driver
side, since the RT counters maintain the statistics of current transaction
now, the maintenance of uc->bcnt is not necessary.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20220802054835.19482-1-vaishnav.a@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver does not handle the failure case while calling
dma_set_mask_and_coherent API.
In case of failure, capture the return value of API and then report an
error.
Addresses-coverity: Unchecked return value (CHECKED_RETURN)
Signed-off-by: Swati Agarwal <swati.agarwal@xilinx.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20220817061125.4720-4-swati.agarwal@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add missing cleanup in devm_platform_ioremap_resource().
When probe fails remove dma channel resources and disable clocks in
accordance with the order of resources allocated .
Signed-off-by: Swati Agarwal <swati.agarwal@xilinx.com>
Link: https://lore.kernel.org/r/20220817061125.4720-2-swati.agarwal@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 MDMA can be triggered by STM32 DMA channels transfer complete.
In case of non-null struct dma_slave_config .peripheral_size, it means the
DMA client wants the DMA to trigger the MDMA.
stm32-mdma driver gets the request id, the mask_addr, and the mask_data in
struct stm32_mdma_dma_config passed by DMA with struct dma_slave_config
.peripheral_config/.peripheral_size.
Then, as DMA is configured in Double-Buffer mode, and MDMA channel will
transfer data from/to SRAM to/from DDR, then bursts are optimized.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-7-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 MDMA can be triggered by STM32 DMA channels transfer complete.
The "request line number" triggering STM32 MDMA is the STM32 DMAMUX channel
id set by stm32-dmamux driver in dma_spec->args[3].
stm32-dma driver fills the struct stm32_dma_mdma_config used to configure
the MDMA with struct dma_slave_config .peripheral_config/.peripheral_size.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-6-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 DMAMUX is used with STM32 DMA1 and DMA2:
- DMAMUX channels 0 to 7 are connected to DMA1 channels 0 to 7
- DMAMUX channels 8 to 15 are connected to DMA2 channels 0 to 7
STM32 MDMA can be triggered by DMA1 and DMA2 channels transfer complete,
and the "request line number" is the DMAMUX channel id (e.g. DMA2 channel 0
triggers MDMA with request line 8).
To well configure MDMA, set DMAMUX channel id in DMA features bitfield,
so that DMA can update struct dma_slave_config peripheral_config properly.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Channels 0 to 3 flags are described in DMA_LISR and DMA_LIFCR (L as Low).
Channels 4 to 7 flags are described in DMA_HISR and DMA_HIFCR (H as High).
Macro STM32_DMA_ISR(n) returns the interrupt status register offset for the
channel id (n).
Macro STM32_DMA_IFCR(n) returns the interrupt flag clear register offset
for the channel id (n).
If chan->id % 4 = 2 or 3, then its flags are left-shifted by 16 bits.
If chan->id % 4 = 1 or 3, then its flags are additionally left-shifted by 6
bits.
If chan->id % 4 = 0, then its flags are not shifted.
Macro STM32_DMA_FLAGS_SHIFT(n) returns the required shift to get or set the
channel flags mask.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds dump of registers with debugfs for HIP08
and HIP09 DMA driver.
Signed-off-by: Jie Hai <haijie1@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20220830062251.52993-7-haijie1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The HiSilicon IP08 and HiSilicon IP09 are DMA iEPs, they
have the same pci device id but different pci revision.
Unfortunately, they have different register layouts, so
the origin driver cannot run on HiSilicon IP09 correctly.
This patch enables the driver to adapt to HiSilicon IP09.
HiSilicon IP09 offers 4 channels, each channel has a send
queue, a complete queue and an interrupt to help to do tasks.
This DMA engine can do memory copy between memory blocks.
Signed-off-by: Jie Hai <haijie1@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20220830062251.52993-6-haijie1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
readl_relaxed_poll_timeout() uses magic numbers 10 and 1000, which
indicate maximum time to sleep between reads in us and timeout in us,
respectively.
Use macros HISI_DMA_POLL_Q_STS_DELAY_US and
HISI_DMA_POLL_Q_STS_TIME_OUT_US instead of these two numbers.
Signed-off-by: Jie Hai <haijie1@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20220830062251.52993-5-haijie1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When we get a DMA channel and try to use it in multiple threads it
will cause oops and hanging the system.
% echo 100 > /sys/module/dmatest/parameters/threads_per_chan
% echo 100 > /sys/module/dmatest/parameters/iterations
% echo 1 > /sys/module/dmatest/parameters/run
[383493.327077] Unable to handle kernel paging request at virtual
address dead000000000108
[383493.335103] Mem abort info:
[383493.335103] ESR = 0x96000044
[383493.335105] EC = 0x25: DABT (current EL), IL = 32 bits
[383493.335107] SET = 0, FnV = 0
[383493.335108] EA = 0, S1PTW = 0
[383493.335109] FSC = 0x04: level 0 translation fault
[383493.335110] Data abort info:
[383493.335111] ISV = 0, ISS = 0x00000044
[383493.364739] CM = 0, WnR = 1
[383493.367793] [dead000000000108] address between user and kernel
address ranges
[383493.375021] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[383493.437574] CPU: 63 PID: 27895 Comm: dma0chan0-copy2 Kdump:
loaded Tainted: GO 5.17.0-rc4+ #2
[383493.457851] pstate: 204000c9 (nzCv daIF +PAN -UAO -TCO -DIT
-SSBS BTYPE=--)
[383493.465331] pc : vchan_tx_submit+0x64/0xa0
[383493.469957] lr : vchan_tx_submit+0x34/0xa0
This occurs because the transmission timed out, and that's due
to data race. Each thread rewrite channels's descriptor as soon as
device_issue_pending is called. It leads to the situation that
the driver thinks that it uses the right descriptor in interrupt
handler while channels's descriptor has been changed by other
thread. The descriptor which in fact reported interrupt will not
be handled any more, as well as its tx->callback.
That's why timeout reports.
With current fixes channels' descriptor changes it's value only
when it has been used. A new descriptor is acquired from
vc->desc_issued queue that is already filled with descriptors
that are ready to be sent. Threads have no direct access to DMA
channel descriptor. In case of channel's descriptor is busy, try
to submit to HW again when a descriptor is completed. In this case,
vc->desc_issued may be empty when hisi_dma_start_transfer is called,
so delete error reporting on this. Now it is just possible to queue
a descriptor for further processing.
Fixes: e9f08b6525 ("dmaengine: hisilicon: Add Kunpeng DMA engine support")
Signed-off-by: Jie Hai <haijie1@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20220830062251.52993-4-haijie1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After completion of data transfer of one or multiple descriptors,
the completion status and the current head pointer to submission
queue are written into the CQ and interrupt can be generated to
inform the software. In interrupt process CQ is read and cq_head
is updated.
hisi_dma_irq updates cq_head only when the completion status is
success. When an abnormal interrupt reports, cq_head will not update
which will cause subsequent interrupt processes read the error CQ
and never report the correct status.
This patch updates cq_head whenever CQ is accessed.
Fixes: e9f08b6525 ("dmaengine: hisilicon: Add Kunpeng DMA engine support")
Signed-off-by: Jie Hai <haijie1@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20220830062251.52993-3-haijie1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When hisi_dma is unloaded or unbinded, all of channels should be
disabled. This patch disables DMA channels when driver is unloaded
or unbinded.
Fixes: e9f08b6525 ("dmaengine: hisilicon: Add Kunpeng DMA engine support")
Signed-off-by: Jie Hai <haijie1@huawei.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20220830062251.52993-2-haijie1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
idxd_device_clear_state() now grabs the idxd->dev_lock
itself, so don't grab the lock prior to calling it.
This was seen in testing after dmar fault occurred on system,
resulting in lockup stack traces.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Fixes: cf4ac3fef3 ("dmaengine: idxd: fix lockdep warning on device driver removal")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20220823163709.2102468-1-jsnitsel@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Qualcomm SM6350 platform does, like the SM8450, provide a set of GPI
controllers with an ee-offset of 0x10000. Add this to the driver.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220812082721.1125759-3-luca.weiss@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9TAR
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Consolidate duplicated 'next function' scanning and extend to allow
'isolated functions' on s390, similar to existing hypervisors
(Niklas Schnelle)
Resource management:
- Implement pci_iobar_pfn() for sparc, which allows us to remove the
sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().
This removes the ability to map the entire PCI I/O space using
/proc/bus/pci, but we believe that's already been broken since
v2.6.28 (Arnd Bergmann)
- Move common PCI definitions to asm-generic/pci.h and rework others
to be be more specific and more encapsulated in arches that need
them (Stafford Horne)
Power management:
- Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)
Virtualization:
- Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
the functions but don't advertise an ACS capability (Pavan Chebbi)
Error handling:
- Clear PCI Status register during enumeration in case firmware left
errors logged (Kai-Heng Feng)
- When we have native control of AER, enable error reporting for all
devices that support AER. Previously only a few drivers enabled
this (Stefan Roese)
- Keep AER error reporting enabled for switches. Previously we
enabled this during enumeration but immediately disabled it (Stefan
Roese)
- Iterate over error counters instead of error strings to avoid
printing junk in AER sysfs counters (Mohamed Khalfella)
ASPM:
- Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
via sysfs, are not lost across power state changes (Kai-Heng Feng)
Endpoint framework:
- Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)
Endpoint embedded DMA controller driver:
- Simplify and clean up support for the DesignWare embedded DMA
(eDMA) controller (Frank Li, Serge Semin)
Broadcom STB PCIe controller driver:
- Avoid config space accesses when link is down because we can't
recover from the CPU aborts these cause (Jim Quinlan)
- Look for power regulators described under Root Ports in DT and
enable them before scanning the secondary bus (Jim Quinlan)
- Disable/enable regulators in suspend/resume (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Simplify and clean up clock and PHY management (Richard Zhu)
- Disable/enable regulators in suspend/resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
- Make link being down a non-fatal error so controller probe doesn't
fail if there are no Endpoints connected (Richard Zhu)
Loongson PCIe controller driver:
- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)
- Avoid config reads to non-existent LS2K/LS7A devices because a
hardware defect causes machine hangs (Huacai Chen)
- Work around LS7A integrated devices that report incorrect Interrupt
Pin values (Jianmin Lv)
Marvell Aardvark PCIe controller driver:
- Add support for AER and Slot capability on emulated bridge (Pali
Rohár)
MediaTek PCIe controller driver:
- Add Airoha EN7532 to DT binding (John Crispin)
- Allow building of driver for ARCH_AIROHA (Felix Fietkau)
MediaTek PCIe Gen3 controller driver:
- Print decoded LTSSM state when the link doesn't come up (Jianjun
Wang)
NVIDIA Tegra194 PCIe controller driver:
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and
Endpoint mode (Vidya Sagar)
- Fix some Root Port interrupt handling issues (Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix Data Link Feature capability programming (Vidya Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya
Sagar)
Qualcomm PCIe controller driver:
- Rework clock, reset, PHY power-on ordering to avoid hangs and
improve consistency (Robert Marko, Christian Marangi)
- Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
- Add support for more than 32 MSI interrupts (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Convert DT binding to json-schema (Herve Codina)
- Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
(Herve Codina)
Samsung Exynos PCIe controller driver:
- Fix phy-exynos-pcie driver so it follows the 'phy_init() before
phy_power_on()' PHY programming model (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Simplify and clean up the DWC core extensively (Serge Semin)
- Fix an issue with programming the ATU for regions that cross a 4GB
boundary (Serge Semin)
- Enable the CDM check if 'snps,enable-cdm-check' exists; previously
we skipped it if 'num-lanes' was absent (Serge Semin)
- Allocate a 32-bit DMA-able page to be MSI target instead of using a
driver data structure that may not be addressable with 32-bit
address (Will McVicker)
- Add DWC core support for more than 32 MSI interrupts (Dmitry
Baryshkov)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Versal CPM5 Gen5 Root Port
(Bharat Kumar Gogada)"
* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
...
New support/Core
- Remove DMA_MEMCPY_SG for lack of users
- Tegra 234 dmaengine support
- Mediatek MT8365 dma support
- Apple ADMAC driver
Updates:
- Yaml conversion for ST-Ericsson DMA40 binding and Freescale edma
- rz-dmac updates and device_synchronize support
- Bunch of typo in comments fixes in drivers
- multithread support in sf-pdma driver
-----BEGIN PGP SIGNATURE-----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=/IFO
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support / Core:
- Remove DMA_MEMCPY_SG for lack of users
- Tegra 234 dmaengine support
- Mediatek MT8365 dma support
- Apple ADMAC driver
Updates:
- Yaml conversion for ST-Ericsson DMA40 binding and Freescale edma
- rz-dmac updates and device_synchronize support
- Bunch of typo in comments fixes in drivers
- multithread support in sf-pdma driver"
* tag 'dmaengine-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (50 commits)
dmaengine: mediatek: mtk-hsdma: Fix typo 'the the' in comment
dmaengine: axi-dmac: check cache coherency register
dmaengine: sh: rz-dmac: Add device_synchronize callback
dmaengine: sprd: Cleanup in .remove() after pm_runtime_get_sync() failed
dmaengine: tegra: Add terminate() for Tegra234
dt-bindings: dmaengine: Add compatible for Tegra234
dmaengine: xilinx: use strscpy to replace strlcpy
dmaengine: imx-sdma: Add FIFO stride support for multi FIFO script
dmaengine: idxd: Correct IAX operation code names
dmaengine: imx-dma: Cast of_device_get_match_data() with (uintptr_t)
dmaengine: dw-axi-dmac: ignore interrupt if no descriptor
dmaengine: dw-axi-dmac: do not print NULL LLI during error
dmaengine: altera-msgdma: Fixed some inconsistent function name descriptions
dmaengine: imx-sdma: Add missing struct documentation
dmaengine: sf-pdma: Add multithread support for a DMA channel
dt-bindings: dma: dw-axi-dmac: extend the number of interrupts
dmaengine: dmatest: use strscpy to replace strlcpy
dmaengine: ste_dma40: fix typo in comment
dmaengine: jz4780: fix typo in comment
dmaengine: s3c24xx: fix typo in comment
...
Pull AVR32 updates from Hans-Christian Noren Egtvedt:
"Mostly changes to documentation and comments"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
video:backlight: remove reference to AVR32 architecture in ltv350qv
video: remove support for non-existing atmel,at32ap-lcdc in atmel_lcdfb
usb:udc: remove reference to AVR32 architecture in Atmel USBA Kconfig
sound:spi: remove reference to AVR32 in Atmel AT73C213 DAC driver
net: remove cdns,at32ap7000-macb device tree entry
misc: update maintainer email address and description for atmel-ssc
mfd: remove reference to AVR32 architecture in atmel-smc.c
dma:dw: remove reference to AVR32 architecture in core.c
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
The AVR32 architecture does no longer exist in the Linux kernel, hence
remove a reference to it in comments to avoid confusion.
Signed-off-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Marking the DMA as cache coherent (dma-coherent in devicetree) is only
safe with versions of axi_dmac that have this feature enabled.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Vinod Koul <vkoul@kernel.org>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Mathias Tausen <mta@satlab.com>
Link: https://lore.kernel.org/r/20220726140213.786939-1-mta@satlab.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some on-chip peripheral modules(for eg:- rspi) on RZ/G2L SoC
use the same signal for both interrupt and DMA transfer requests.
The signal works as a DMA transfer request signal by setting
DMARS, and subsequent interrupt requests to the interrupt controller
are masked.
We can re-enable the interrupt by clearing the DMARS.
This patch adds device_synchronize callback for clearing
DMARS and thereby allowing DMA consumers to switch to
interrupt mode.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220722084430.969333-1-biju.das.jz@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It's not allowed to quit remove early without cleaning up completely.
Otherwise this results in resource leaks that probably yield graver
problems later. Here for example some tasklets might survive the lifetime
of the sprd-dma device and access sdev which is freed after .remove()
returns.
As none of the device freeing requires an active device, just ignore the
return value of pm_runtime_get_sync().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20220721204054.323602-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In certain cases where the DMA client bus gets corrupted or if the
end device ceases to send/receive data, DMA can wait indefinitely
for the data to be received/sent. Attempting to terminate the transfer
will put the DMA in pause flush mode and it remains there.
The channel is irrecoverable once this pause times out in Tegra194 and
earlier chips. Whereas, from Tegra234, it can be recovered by disabling
the channel and reprograming it.
Hence add a new terminate() function that ignores the outcome of
dma_pause() so that terminate_all() can proceed to disable the channel.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220720104045.16099-3-akhilrajeev@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The strlcpy should not be used because it doesn't limit the source
length. Preferred is strscpy.
Signed-off-by: XueBing Chen <chenxuebing@jari.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/39aa840f.e31.181ed9461c2.Coremail.chenxuebing@jari.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The peripheral may have several FIFOs, but some case just select
some FIFOs from them for data transfer, which means FIFO0 and FIFO2
may be selected. So add FIFO address stride support, 0 means all FIFOs
are continuous, 1 means 1 word stride between FIFOs. All stride between
FIFOs should be same.
Another option words_per_fifo means how many audio channel data copied
to one FIFO one time, 1 means one channel per FIFO, 2 means 2 channels
per FIFO.
If 'n_fifos_src = 4' and 'words_per_fifo = 2', it means the first two
words(channels) fetch from FIFO0 and then jump to FIFO1 for next two words,
and so on after the last FIFO3 fetched, roll back to FIFO0.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1657162829-9273-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the channel has no descriptor and the interrupt is raised then the
kernel will OOPS. Check the result of vchan_next_desc() in the handler
axi_chan_block_xfer_complete() to avoid the error happening.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Link: https://lore.kernel.org/r/20220708170153.269991-4-ben.dooks@sifive.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During debugging we have seen an issue where axi_chan_dump_lli()
is passed a NULL LLI pointer which ends up causing an OOPS due
to trying to get fields from it. Simply print NULL LLI and exit
to avoid this.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Link: https://lore.kernel.org/r/20220708170153.269991-3-ben.dooks@sifive.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Inconsistent function names describing msgdma_chan_remove() and
msgdma_dma_remove are modified to msgdma_dev_remove() and msgdma_remove().
Remove some warnings found by running scripts/kernel-doc, which is caused
by using 'make W=1'.
drivers/dma/altera-msgdma.c:927: warning: expecting prototype for msgdma_dma_remove(). Prototype was for msgdma_remove() instead.
drivers/dma/altera-msgdma.c:758: warning: expecting prototype for msgdma_chan_remove(). Prototype was for msgdma_dev_remove() instead.
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Link: https://lore.kernel.org/r/20220706082605.114907-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix compile warning that 'Function parameter or member not described'
with 'W=1' option:
Add missing description for struct sdma_desc
There is not any description for struct sdma_script_start_addrs,
so use /* instead of /**
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1657086309-7964-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When we get a DMA channel and try to use it in multiple threads it
will cause oops and hanging the system.
% echo 64 > /sys/module/dmatest/parameters/threads_per_chan
% echo 10000 > /sys/module/dmatest/parameters/iterations
% echo 1 > /sys/module/dmatest/parameters/run
[ 89.480664] Unable to handle kernel NULL pointer dereference at virtual
address 00000000000000a0
[ 89.488725] Oops [#1]
[ 89.494708] CPU: 2 PID: 1008 Comm: dma0chan0-copy0 Not tainted
5.17.0-rc5
[ 89.509385] epc : vchan_find_desc+0x32/0x46
[ 89.513553] ra : sf_pdma_tx_status+0xca/0xd6
This happens because of data race. Each thread rewrite channels's
descriptor as soon as device_prep_dma_memcpy() is called. It leads to the
situation when the driver thinks that it uses right descriptor that
actually is freed or substituted for other one.
With current fixes a descriptor changes its value only when it has
been used. A new descriptor is acquired from vc->desc_issued queue that
is already filled with descriptors that are ready to be sent. Threads
have no direct access to DMA channel descriptor. Now it is just possible
to queue a descriptor for further processing.
Fixes: 6973886ad5 ("dmaengine: sf-pdma: add platform DMA support for HiFive Unleashed A00")
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Link: https://lore.kernel.org/r/20220701082942.12835-1-v.v.mitrofanov@yadro.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220521111145.81697-17-Julia.Lawall@inria.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
ldma_clk_disable() calls both:
clk_disable_unprepare(d->core_clk);
reset_control_assert(d->rst);
So, should devm_reset_control_get_optional() fail, core_clk should not
be prepare_enable'd before it, otherwise it will never be
disable_unprepare'd.
Reorder the code to handle the error handling path as expected.
Fixes: 32d31c79a1 ("dmaengine: Add Intel LGM SoC DMA support.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/18504549bc4d2b62a72a02cb22a2e4d8e6a58720.1653241224.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220521111145.81697-20-Julia.Lawall@inria.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220521111145.81697-46-Julia.Lawall@inria.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DEFINE_SPINLOCK() macro shouldn't be used for dynamically allocated
spinlocks. The lockdep warns about this and disables locking validator.
Fix the warning by making lock static.
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
Hardware name: Radxa ROCK Pi 4C (DT)
Call trace:
dump_backtrace.part.0+0xcc/0xe0
show_stack+0x18/0x6c
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
register_lock_class+0x4a8/0x4cc
__lock_acquire+0x78/0x20cc
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x68/0x84
_raw_spin_lock_irqsave+0x84/0xc4
add_desc+0x44/0xc0
pl330_get_desc+0x15c/0x1d0
pl330_prep_dma_cyclic+0x100/0x270
snd_dmaengine_pcm_trigger+0xec/0x1c0
dmaengine_pcm_trigger+0x18/0x24
...
Fixes: e588710311 ("dmaengine: pl330: fix descriptor allocation fail")
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://lore.kernel.org/r/20220520181432.149904-1-dmitry.osipenko@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the function xilinx_dpdma_probe(), when get irq failed,
the function platform_get_irq() logs an error message,
so remove redundant message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20220519130855.7664-1-tangbin@cmss.chinamobile.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sun4i DMA engine supports transfer sizes up to 128k for normal DMA
and 16M for dedicated DMA, as documented in the A10 and A20 manuals.
Since this is larger than the default segment size limit (64k), exposing
the real limit reduces the number of transfers needed for a transaction.
However, because the device can only report one segment size limit, we
have to expose the smaller limit from normal DMA.
One complication is that the driver combines pairs of periodic transfers
to reduce programming overhead. This only works when the period size is
at most half of the maximum transfer size. With the default 64k segment
size limit, this was always the case, but for normal DMA it is no longer
guaranteed. Skip the optimization if the period is too long; even
without it, the overhead is less than before.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220621031350.36187-1-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Radhey Shyam Pandey