I am using a USB keyborad that give me "usb_submit_urb(ctrl) failed: -1" error
when I plugin it. and I need to wait for 10s for this device to be ready.
By adding this quirks, the usb keyborad is usable right after plugin
Signed-off-by: Wangzhao Cai <microcaicai@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver adds support for USB controlled led panels that exists in
MSI GT683R laptop
Signed-off-by: Janne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
These device needs to be added to the quirks list with HID_QUIRK_NOGET,
otherwise they will reset upon receiving the get input report requests.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The quirks_param array is located in the BSS, no need to explicitly
initialize it with NULL.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device which identifies itself as a "USB Keykoard" (no typo) with VID:PID
1a2c:0023 does not seem to be handling the reports initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the kernel
when connected, and a delay before its initialization. This patch adds the
quirk for this device, which causes the delay to disappear.
[jkosina@suse.cz: remove superfluous comment and fix ordering]
Signed-off-by: Daniel Kamil Kozar <dkk089@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This touchpad seriously dislikes init reports, not only timeing out, but
also refusing to work after this.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Vincent Fortier <th0ma7@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Nobody calls hid_output_raw_report anymore, and nobody should.
We can now remove the various implementation in the different
transport drivers and the declarations.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_out_raw_report is going to be obsoleted as it is not part of the
unified HID low level transport documentation
(Documentation/hid/hid-transport.txt)
To do so, we need to introduce two new quirks:
* HID_QUIRK_NO_OUTPUT_REPORTS_ON_INTR_EP: this quirks prevents the
transport driver to use the interrupt channel to send output report
(and thus force to use HID_REQ_SET_REPORT command)
* HID_QUIRK_SKIP_OUTPUT_REPORT_ID: this one forces usbhid to not
include the report ID in the buffer it sends to the device through
HID_REQ_SET_REPORT in case of an output report
This also fixes a regression introduced in commit 3a75b24949
(HID: hidraw: replace hid_output_raw_report() calls by appropriates ones).
The hidraw API was not able to communicate with the PS3 SixAxis
controllers in USB mode.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If there is no urbout when sending a output report, ENOSYS (Function
not implemented) is a better error than EIO (I/O error).
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
dev->hid_get_raw_report(X) and hid_hw_raw_request(X, HID_REQ_GET_REPORT)
are strictly equivalent. Switch the hid subsystem to the hid_hw notation
and remove the field .hid_get_raw_report in struct hid_device.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Well, no use to keep twice the same code.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add raw_request, set_raw_report and output_report transport-driver functions to
the USB HID driver.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Synaptics HD touchscreen(06cb:1ac3) to no init report quirk
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Synaptics HD touchscreen(06cb:0ac3) to no init report quirk.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB_VENDOR_ID_SIS and USB_VENDOR_ID_SIS2_TOUCH are identical,
so refine the code and merge the quirks.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It looks like this typo was introduced by a mistake in a copy-and-paste in
commit ddbe324919.
Signed-off-by: Adam Cozzette <acozzette@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BugLink: http://bugs.launchpad.net/bugs/1180881
This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.
[12431.828467] hid-multitouch 0003:0457:1013.0475: usb_submit_urb(ctrl) failed: -1
[12431.828507] hid-multitouch 0003:0457:1013.0475: timeout initializing reports
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BugLink: http://bugs.launchpad.net/bugs/1180881
Synaptics large touchscreen doesn't support some of the report request
while initializing. The unspoorted request will make the device unreachable,
and will lead to the following usb_submit_urb() function call timeout.
So, add the IDs into HID_QUIRK_NO_INIT_REPORTS quirk.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DuoSense touchscreen device causes a 10 second timeout. This fix
removes the delay.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some multitouch screens do not like to be polled for input reports.
However, the Win8 spec says that all touches should be sent during
each report, making the initialization of reports unnecessary.
The Win7 spec is less precise, so do not use this for those devices.
Add the quirk HID_QUIRK_NO_INIT_INPUT_REPORTS so that we do not have to
introduce a quirk for each problematic device. This quirk makes the driver
behave the same way the Win 8 does. It actually retrieves the features,
but not the inputs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID core provides the same functionality as we do, so drop the custom
hidinput_input_event() handler.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report fields can be updated from HID drivers unlocked via
hid_set_field(). It is protected by input_lock in HID core so only a
single input event is handled at a time. USBHID can thus update the field
unlocked and doesn't conflict with any HID vendor/device drivers. Note,
many HID drivers make heavy use of hid_set_field() in that way.
But usbhid also schedules a work to gather multiple LED changes in a
single report. Hence, we used to lock the LED field update so the work can
read a consistent state. However, hid_set_field() only writes a single
integer field, which is guaranteed to be allocated all the time. So the
worst possible race-condition is a garbage read on the LED field.
Therefore, there is no need to protect the update. In fact, the only thing
that is prevented by locking hid_set_field(), is an LED update while the
scheduled work currently writes an older LED update out. However, this
means, a new work is scheduled directly when the old one is done writing
the new state to the device. So we actually _win_ by not protecting the
write and allowing the write to be combined with the current write. A new
worker is still scheduled, but will not write any new state. So the LED
will not blink unnecessarily on the device.
Assume we have the LED set to 0. Two request come in which enable the LED
and immediately disable it. The current situation with two CPUs would be:
usb_hidinput_input_event() | hid_led()
---------------------------------+----------------------------------
spin_lock(&usbhid->lock);
hid_set_field(1);
spin_unlock(&usbhid->lock);
schedule_work(...);
spin_lock(&usbhid->lock);
__usbhid_submit_report(..1..);
spin_unlock(&usbhid->lock);
spin_lock(&usbhid->lock);
hid_set_field(0);
spin_unlock(&usbhid->lock);
schedule_work(...);
spin_lock(&usbhid->lock);
__usbhid_submit_report(..0..);
spin_unlock(&usbhid->lock);
With the locking removed, we _might_ end up with (look at the changed
__usbhid_submit_report() parameters in the first try!):
usb_hidinput_input_event() | hid_led()
---------------------------------+----------------------------------
hid_set_field(1);
schedule_work(...);
spin_lock(&usbhid->lock);
hid_set_field(0);
schedule_work(...);
__usbhid_submit_report(..0..);
spin_unlock(&usbhid->lock);
... next work ...
spin_lock(&usbhid->lock);
__usbhid_submit_report(..0..);
spin_unlock(&usbhid->lock);
As one can see, we no longer send the "LED ON" signal as it is disabled
immediately afterwards and the following "LED OFF" request overwrites the
pending "LED ON".
It is important to note that hid_set_field() is not atomic, so we might
also end up with any other value. But that doesn't matter either as we
_always_ schedule the next work with a correct value and schedule_work()
acts as memory barrier, anyways. So in the worst case, we run
__usbhid_submit_report(..<garbage>..) in the first case and the following
__usbhid_submit_report() will write the correct value. But LED states are
booleans so any garbage will be converted to either 0 or 1 and the remote
device will never see invalid requests.
Why all this? It avoids any custom locking around hid_set_field() in
usbhid and finally allows us to provide a generic hidinput_input_event()
handler for all HID transport drivers.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
usbhid_set_leds() is only used inside of usbhid/hid-core.c so no need to
export it.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
implement() is setting bytes in LE data stream. In case the data is not
aligned to 64bits, it reads past the allocated buffer. It doesn't really
change any value there (it's properly bitmasked), but in case that this
read past the boundary hits a page boundary, pagefault happens when
accessing 64bits of 'x' in implement(), and kernel oopses.
This happens much more often when numbered reports are in use, as the
initial 8bit skip in the buffer makes the whole process work on values
which are not aligned to 64bits.
This problem dates back to attempts in 2005 and 2006 to make implement()
and extract() as generic as possible, and even back then the problem
was realized by Adam Kroperlin, but falsely assumed to be impossible
to cause any harm:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg47690.html
I have made several attempts at fixing it "on the spot" directly in
implement(), but the results were horrible; the special casing for processing
last 64bit chunk and switching to different math makes it unreadable mess.
I therefore took a path to allocate a few bytes more which will never make
it into final report, but are there as a cushion for all the 64bit math
operations happening in implement() and extract().
All callers of hid_output_report() are converted at the same time to allocate
the buffer by newly introduced hid_alloc_report_buf() helper.
Bruno noticed that the whole raw_size test can be dropped as well, as
hid_alloc_report_buf() makes sure that the buffer is always of a proper
size.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- hid driver transport cleanup, finalizing the long-desired decoupling
of core from transport layers, by Benjamin Tissoires and Henrik
Rydberg
- support for hybrid finger/pen multitouch HID devices, by Benjamin
Tissoires
- fix for long-standing issue in Logitech unifying driver sometimes not
inializing properly due to device specifics, by Andrew de los Reyes
- Wii remote driver updates to support 2nd generation of devices, by
David Herrmann
- support for Apple IR remote
- roccat driver now supports new devices (Roccat Kone Pure, IskuFX), by
Stefan Achatz
- debugfs locking fixes in hid debug interface, by Jiri Kosina
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (43 commits)
HID: protect hid_debug_list
HID: debug: break out hid_dump_report() into hid-debug
HID: Add PID for Japanese version of NE4K keyboard
HID: hid-lg4ff add support for new version of DFGT wheel
HID: icade: u16 which never < 0
HID: clarify Magic Mouse Kconfig description
HID: appleir: add support for Apple ir devices
HID: roccat: added media key support for Kone
HID: hid-lenovo-tpkbd: remove doubled hid_get_drvdata
HID: i2c-hid: fix length for set/get report in i2c hid
HID: wiimote: parse reduced status reports
HID: wiimote: add 2nd generation Wii Remote IDs
HID: wiimote: use unique battery names
HID: hidraw: warn if userspace headers are outdated
HID: multitouch: force BTN_STYLUS for pen devices
HID: multitouch: append " Pen" to the name of the stylus input
HID: multitouch: add handling for pen in dual-sensors device
HID: multitouch: change touch sensor detection in mt_input_configured()
HID: multitouch: do not map usage from non used reports
HID: multitouch: breaks out touch handling in specific functions
...
If suspend callback fails in system sleep context, usb core will
ignore the failure and let the system sleep go ahead further, so this
patch doesn't recover device under this situation, otherwise
may cause resume() confused.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build problem caused by typo introduced by 620ae90ed8
("HID: usbhid: quirk for MSI GX680R led panel").
Reported-by: fengguang.wu@intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This keyboard backlight device causes a 10 second delay to boot. Add it
to the quirk list with HID_QUIRK_NO_INIT_REPORTS.
This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=907221
Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.
This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=806587
Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers send the idle command directly to underlying device,
creating an unwanted dependency on the underlying transport layer.
This patch adds hid_hw_idle() to the interface, thereby removing
usbhid from the lion share of the drivers.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removes most of the dependencies between hid drivers and usbhid.
The patch was constructed by replacing all occurences of
usbhid_wait_io() by its hid_hw_wait() counterpart.
Then, drivers not requiring USB_HID anymore have their USB_HID
dependency cleaned in the Kconfig file.
As of today, few drivers are still requiring an explicit USB layer
dependency:
* ntrig (a patch is on its way)
* multitouch (one patch following and another on its way)
* lenovo tpkbd
* roccat
* sony
The last three are two deeply using direct calls to the usb subsystem
to be able to be cleaned right now.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This allows the hid drivers to be independent from the transport layer.
The patch was constructed by replacing all occurences of
usbhid_submit_report() by its hid_hw_request() counterpart.
Then, drivers not requiring USB_HID anymore have their USB_HID
dependency cleaned in the Kconfig file.
Finally, few drivers still depends on USB_HID. Many of them
are requiring the io wait callback. They are found in the next patch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For the sensor-hub part:
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers need to wait for an io from the underlying device, creating
an unwanted dependency on the underlying transport layer. This patch adds
wait() to the interface, thereby removing usbhid from the lion share of
the drivers.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers send reports directly to underlying device, creating an
unwanted dependency on the underlying transport layer. This patch adds
hid_hw_request() to the interface, thereby removing usbhid from the
lion share of the drivers.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Patch to add the Formosa Industrial Computing, Inc. Infrared Receiver
[IR605A/Q] to hid-ids.h and hid-quirks.c. This IR receiver causes about a 10
second timeout when the usbhid driver attempts to initialze the device. Adding
this device to the quirks list with HID_QUIRK_NO_INIT_REPORTS removes the
delay.
Signed-off-by: Nicholas Santos <nicholas.santos@gmail.com>
[jkosina@suse.cz: fix ordering]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds