For eMMC devices it is valid to only support 1.8V signaling. When
vqmmc is set to a fixed 1.8V regulator the stack tries to set 3.3V
initially and prints the following warning:
mmc1: Switching to 3.3V signalling voltage failed
Clear the MMC_SIGNAL_VOLTAGE_330 flag in case 3.3V is signaling is
not available. This prevents the stack from even trying to use
3.3V signaling and avoids the above warning.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI controller in ls1043a and ls1046a generate 40-bit wide addresses
when doing DMA. Make sure that the corresponding dma mask is correctly
configured.
Context: when enabling smmu on these chips the following problem is
encountered: the smmu input address size is 48 bits so the dma mappings
for sdhci end up 48-bit wide. However, on these chips sdhci only use
40-bits of that address size when doing dma.
So you end up with a 48-bit address translation in smmu but the device
generates transactions with clipped 40-bit addresses, thus smmu context
faults are triggered. Setting up the correct dma mask fixes this
situation.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A recent commit introduced a call to mmc_of_parse() and removed the
explicit assignment of GPIOs in the pdata structure. This will leave
them set to 0, which is a valid GPIO per se, so the code that looks
at these members will try to allocate them and fail.
To fix this properly, make the following changes:
a) Refrain from allocating and assiging a pdata struct from
pxamci_of_init(). It's a hack to do it this way anyway.
Instead, move the only remaining member of interest in
'struct pxamci_host' and assign the value from either
the passed in pdata pointer or with the value read from DT.
b) Let the only user of 'detect_delay_ms' look at the member of
'struct pxamci_host', not the pdata.
c) Make more code in pxamci_probe() dependent on the presence of
actual pdata.
This will also ease the removal of pdata one day.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Strip some code by letting the mmc core handle the regulators. The old
.gpio_power pdata handling is kept around for now.
This also set the voltage on the regulator and handles -EPROBE_DEFER
correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Devicetree-enabled boards should use proper regulators to control the
power of cards, not GPIOs, so let's remove this property. The regulator
properties are supported by the MMC core and are described in the
generic MMC document:
Documentation/devicetree/bindings/mmc/mmc.txt
Note that devicetree support for PXA platforms hasn't fully landed yet,
so this binding does not have any users at this point.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Call into mmc_of_parse() from pxamci_of_init(). As it needs a pointer to a
struct mmc_host, refactor the code a bit.
This allows all generic MMC properties to be set that are described in
Documentation/devicetree/bindings/mmc/mmc.txt. Reword the documentation
a bit to make that clear.
The "cd" and "wp" gpio lookups are removed as the lookup will now be
done by mmc_of_parse().
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
pxamci_of_init() had some weird indenting.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These gpio assignments don't make sense, as they are not used anywhere.
Remove the dead code.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These members are no longer in use, so let's remove them.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This seems to be a left-over from times before the IRQ was handled by devm
functions. Remove it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The field support_vsel is currently only used in the device tree
case. Get rid of it. No change in behavior.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The uSDHC supports DDR modes for eMMC devices running at 3.3V. This
allows to run eMMC with 3.3V signaling voltage at DDR52 mode:
# cat /sys/kernel/debug/mmc1/ios
clock: 52000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 3 (8 bits)
timing spec: 8 (mmc DDR52)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last user of mmc_power_save|restore_host() APIs is gone, hence let's
drop them. Drop also the corresponding bus_ops callback,
->power_save|restore() as those becomes redundant.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Eyal Reizer <eyalreizer@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to use of_match_node method to fix up eSDHC clock for
ls1046a/ls1012a/p1010. Also add eSDHC clock fixup for ls1021a
according to its datasheet. The maxmum speed for ls1021a eSDHC
high speed mode is 46.5MHz.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers immediately report SDHCI_CLOCK_INT_STABLE after
enabling the clock even when the clock is not stable. When used in
conjunction with older/slower cards, this can result in:
mmc0: error -84 whilst initialising SD card
When the stable reporting is known to be broken, we simply wait for the
maximum stabilization period.
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to use the new compatible string "qcom,sdhci-msm-v5".
Based on the msm variant, pick the relevant variant data and
use it for register read/write to msm specific registers.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In addition to offsets of certain registers changing, the registers in
core_mem have been shifted to HC mem as well. To access these
registers, define msm version specific functions. These functions can
be loaded into the function pointers at the time of probe based on
the msm version detected.
Also defind new data structure to hold version specific Ops and
register addresses.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDCC version 5.0.0, MCI registers are removed from SDCC
interface and some registers are moved to HC.
Define a new data structure where we can statically define
the address offsets for the registers in different SDCC versions.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds two new HS400 tuning operations:
* hs400_downgrade
* hs400_complete
These supplement the existing HS400 operation:
* prepare_hs400_tuning
This is motivated by a requirement of Renesas SDHI for the following:
1. Disabling SCC before selecting to HS if selection of HS400 has occurred.
This can be done in an implementation of prepare_hs400_tuning_downgrade
2. Updating registers after switching to HS400
This can be done in an implementation of complete_hs400_tuning
If hs400_downgrade or hs400_complete are not implemented then they are not
called. Thus means there should be no affect for existing drivers as none
implemt these ops.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_exynos_resume_noirq() performs DWMMC register access without
ensuring that respective clocks are enabled. This might cause external
abort on some systems (observed on Exynos5433 based boards). Fix this
by forcing a PM runtime active state before register access. Using
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS allows also to cleanup conditional code
a bit.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci get_max_clock callback is set to sdhci_pltfm_clk_get_max_clock
and tegra_sdhci_get_max_clock is removed. It appears that the
shdci-tegra specific callback was originally introduced due to the
requirement that the host clock has to be twice the bus clock on DDR50
mode. As far as I can tell the only effect the removal has on DDR50 mode
is in cases where the parent clock is unable to supply the requested
clock rate, causing the DDR50 mode to run at a lower frequency.
Currently the DDR50 mode isn't enabled on any of the SoCs and would also
require configuring the SDHCI clock divider register to function
properly.
The problem with tegra_sdhci_get_max_clock is that it divides the clock
rate by two and thus artificially limits the maximum frequency of faster
signaling modes which don't have the host-bus frequency ratio requirement
of DDR50 such as SDR104 and HS200. Furthermore, the call to
clk_round_rate() may return an error which isn't handled by
tegra_sdhci_get_max_clock.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.
As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.
So reusing R1_STATUS for them not only improve the readability but also
slove real problems.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc host controller enters suspend state, the clocks are
disabled, but irqs are not. For some reason the irqchip emits
false interrupts, which causes system lock loop.
Debug log is:
...
sunxi-mmc 1c11000.mmc: setting clk to 52000000, rounded 51200000
sunxi-mmc 1c11000.mmc: enabling the clock
sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
sunxi-mmc 1c11000.mmc: cmd 6(80000146) arg 3210101 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 AGND3R 14.6 GiB
mmcblk1boot0: mmc1:0001 AGND3R partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 AGND3R partition 2 4.00 MiB
sunxi-mmc 1c11000.mmc: cmd 18(80003352) arg 0 ie 0x0000fbc2 len 409
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00004000 idi 00000002
mmcblk1: p1
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
and so on...
This issue apears on eMMC cards, routed on MMC2 slot. The patch is
tested with A20-OLinuXino-MICRO/LIME/LIME2 boards.
Fixes: 9a8e1e8cc2 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Card write threshold control is supposed to be set since controller
version 2.80a for data write in HS400 mode and data read in
HS200/HS400/SDR104 mode. However the current code returns without
configuring it in the case of data writing in HS400 mode.
Meanwhile the patch fixes that the current code goes to
'disable' when doing data reading in HS400 mode.
Fixes: 7e4bf1bc95 ("mmc: dw_mmc: add the card write threshold for HS400 mode")
Signed-off-by: Qing Xia <xiaqing17@hisilicon.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bfd694d5e2 ("mmc: core: Add tunable delay
before detecting card after card is inserted") adds
"u32 cd_debounce_delay_ms" to the last of mmc_gpio
struct and cause "char cd_label[0]" NOT work as string
pointer of card detect label, when "cat /proc/interrupts",
the devname for card detect gpio is incorrect as below:
144: 0 gpio-mxc 22 Edge ▒
161: 0 gpio-mxc 7 Edge ▒
Move the cd_label field down to fix this, and drop the
zero from the array size to prevent future similar bugs,
the result is correct as below:
144: 0 gpio-mxc 22 Edge 2198000.mmc cd
161: 0 gpio-mxc 7 Edge 2190000.mmc cd
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card after card is inserted")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is fixes an issue that the SDHI_INTERNAL_DMAC_RX_IN_USE
flag cannot be cleared because tmio_mmc_core sets the host->data
to NULL before the tmio_mmc_core calls tmio_mmc_abort_dma().
So, this patch clears the SDHI_INTERNAL_DMAC_RX_IN_USE in
the renesas_sdhi_internal_dmac_abort_dma() anyway. This doesn't
cause any side effects.
Fixes: 0cbc94daa5 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes an issue that lacks the dma_unmap_sg() calling in
the error patch of renesas_sdhi_internal_dmac_start_dma().
Fixes: 0cbc94daa5 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching
-----BEGIN PGP SIGNATURE-----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=MwCT
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching"
* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
mmc: renesas_sdhi: really fix WP logic regressions
mmc: mvsdio: Enable MMC_CAP_ERASE
mmc: mvsdio: Respect card busy time out from mmc core
mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
mmc: sunxi: Use ifdef rather than __maybe_unused
mmc: mxmmc: Use ifdef rather than __maybe_unused
mmc: mxmmc: include linux/highmem.h
mmc: sunxi: mark PM functions as __maybe_unused
mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
mmc: au1xmmc: handle highmem pages
mmc: Allow non-sleeping GPIO cd
mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
mmc: sd: Define name for default speed dtr
mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
mmc: sdhci-xenon: use match_string() helper
mmc: wbsd: handle highmem pages
mmc: ushc: handle highmem pages
mmc: mxcmmc: handle highmem pages
mmc: atmel-mci: use sg_copy_{from,to}_buffer
mmc: android-goldfish: use sg_copy_{from,to}_buffer
...
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
This reverts commit e060d376cc ("mmc: renesas_sdhi: fix WP detection")
and adds some code to really fix the regressions.
It was missed so far that Renesas R-Car instantiations of SDHI chose to
disable internal WP and used the existence of "wp-gpios" to en/disable
WP at all.
With the first refactoring by Yamada-san with commit 2ad1db059b ("mmc:
renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of TMIO own flag"),
WP was always disabled even when GPIOs were present. With Wolfram's
first fix which gets now reverted, GPIOs were honored. But when not
available, the fallback was to internal WP and not to disabled WP. This
caused wrong WP status on uSD card slots.
Restore the old behaviour now. By default, WP is disabled. When a GPIO
is found, the GPIO re-enables WP. We will think about possible better
ways to handle this in the future.
Tested on a previously regressing Renesas Lager board (H2) and a still
working Renesas Salvator-X board (M3-W).
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
There is no obvious reasons to why mvsdio shouldn't be able to support
erase/trim/discard operations, hence let's set MMC_CAP_ERASE for it.
Cc: Damien Thebault <damien.thebault@vitec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Damien Thebault <damien.thebault@vitec.com>
Instead of using a hardcoded timeout of 5 * HZ jiffies, let's respect the
command busy timeout provided by the mmc core. This make the used timeout
more reliable.
Cc: Damien Thebault <damien.thebault@vitec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Damien Thebault <damien.thebault@vitec.com>
Now we have a proper implementation for the power irq handling and this
quirk is not needed anymore. In fact, it is causing card detection delays
on apq8096 platforms and the following error is displayed:
sdhci_msm 74a4900.sdhci: mmc0: pwr_irq for req: (4) timed out
The quirk is forcing the controller to retain 1.8V signalling on the slot
even when a new card is inserted, which is not correct. The proper behavior
would be to reset the controller in order to start with 3.3V signaling.
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Suggested-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent with code in other mmc host drivers, convert to check the
correct PM config #ifdef in favor of using __maybe_unused.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent with code in other mmc host drivers, convert to check the
correct PM config #ifdef in favor of using __maybe_unused.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By completing the request entirely in the driver we can remove the
BLK_EH_HANDLED return value and thus the split responsibility between the
driver and the block layer that has been causing trouble.
[While this keeps existing behavior it seems to mismatch the comment,
maintainers please chime in!]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The highmem conversion caused a build error in some configurations:
drivers/mmc/host/mxcmmc.c: In function 'mxcmci_transfer_data':
drivers/mmc/host/mxcmmc.c:622:10: error: implicit declaration of function 'kmap_atomic'; did you mean 'in_atomic'? [-Werror=implicit-function-declaration]
This includes the correct header file.
Fixes: b189e7589f ("mmc: mxcmmc: handle highmem pages")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stefan Agner