The variant init function may need to add a mmc_host_ops, for example to
add the execute_tuning support if this feature is available. This patch
adds mmc_host_ops pointer in mmci struct.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-4-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sg_dma_xxx should be used after a dma_map_sg call has been done to get bus
addresses of each of the SG entries and their lengths. But mmci_host_ops
validate_data can be called before dma_map_sg. This patch replaces theses
macros by sg->offset and sg->length which are always defined.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200128090636.13689-2-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case the host specify a max_busy_timeout, we need to validate that the
needed timeout for the HPI command conforms to that requirement. If that's
not the case, let's convert from a R1B response to a R1 response, as to
instruct the host to avoid HW busy detection.
Additionally, when R1B is used we must also inform the host about the busy
timeout for the command, so let's do that via updating cmd.busy_timeout.
Finally, when R1B is used and in case the host supports HW busy detection,
there should be no need for doing polling, so then skip that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-12-ulf.hansson@linaro.org
Rather than open coding the polling loop in mmc_interrupt_hpi(), let's
convert to use mmc_poll_for_busy().
Note that, moving to mmc_poll_for_busy() for HPI also improves the
behaviour according to below.
- Adds support for polling via the optional ->card_busy() host ops.
- Require R1_READY_FOR_DATA to be set in the CMD13 response before exiting
the polling loop.
- Adds a throttling mechanism to avoid CPU hogging when polling.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-11-ulf.hansson@linaro.org
The 'u32 *status' is unused by the caller, so let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-10-ulf.hansson@linaro.org
Rather than open coding the polling loop in mmc_do_erase(), let's convert
to use mmc_poll_for_busy().
To allow a slightly different error parsing during polling, compared to the
__mmc_switch() case, a new in-parameter to mmc_poll_for_busy() is needed,
but other than that the conversion is straight forward.
Besides addressing the open coding issue, moving to mmc_poll_for_busy() for
erase/trim/discard improves the behaviour according to below.
- Adds support for polling via the optional ->card_busy() host ops.
- Returns zero to indicate success when the final polling attempt finds the
card non-busy, even if the timeout expired.
- Exits the polling loop when state moves to R1_STATE_TRAN, rather than
when leaving R1_STATE_PRG.
- Decreases the starting range for throttling to 32-64us.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-9-ulf.hansson@linaro.org
Through mmc_poll_for_busy() a CMD13 may be sent to get the status of the
(e)MMC card. If the state of the card is R1_STATE_PRG, the card is
considered as being busy, which means we continue to poll with CMD13. This
seems to be sufficient, but it's also unnecessary fragile, as it means a
new command/request could potentially be sent to the card when it's in an
unknown state.
To try to improve the situation, but also to move towards a more consistent
CMD13 polling behaviour in the mmc core, let's deploy the same policy we
use for regular I/O write requests. In other words, let's check that card
returns to the R1_STATE_TRAN and that the R1_READY_FOR_DATA bit is set in
the CMD13 response, before exiting the polling loop.
Note that, potentially this changed behaviour could lead to unnecessary
waiting for the timeout to expire, if the card for some reason, moves to an
unexpected error state. However, as we bail out from the polling loop when
R1_SWITCH_ERROR bit is set or when the CMD13 fails, this shouldn't be an
issue.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-8-ulf.hansson@linaro.org
To allow subsequent changes to re-use the code from the static function
mmc_blk_in_tran_state(), let's move it to a public header. While at it,
let's also rename it to mmc_ready_for_data(), as to try to better describe
its purpose.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-7-ulf.hansson@linaro.org
To make the code more readable, move the part that gets the busy status of
the card out into a separate function, mmc_busy_status(). Then call it from
mmc_poll_for_busy().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-6-ulf.hansson@linaro.org
The use_busy_signal in-parameter is set true by all callers of
__mmc_switch(), hence it's redundant so drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-5-ulf.hansson@linaro.org
To simplify code, let's extend mmc_switch_status() to cope with needs
addressed in __mmc_switch_status(). Then move all users to the updated
mmc_switch_status() API and drop __mmc_switch_status() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-4-ulf.hansson@linaro.org
The last user of MMC_OPS_TIMEOUT_MS was recently removed, however the
define stayed around. Let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-3-ulf.hansson@linaro.org
In mmc_poll_for_busy() we loop continuously, either by sending a CMD13 or
by invoking the ->card_busy() host ops, as to detect when the card stops
signaling busy. This behaviour is problematic as it may cause CPU hogging,
especially when the busy signal time reaches beyond a few ms.
Let's fix the issue by adding a throttling mechanism, that inserts a
usleep_range() in between the polling attempts. The sleep range starts at
32-64us, but increases for each loop by a factor of 2, up until the range
reaches ~32-64ms. In this way, we are able to keep the loop fine-grained
enough for short busy signaling times, while also not hogging the CPU for
longer times.
Note that, this change is inspired by the similar throttling mechanism that
we already use for mmc_do_erase().
Reported-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200204085449.32585-2-ulf.hansson@linaro.org
When using the host software queue, it will trigger the next request in
irq handler without a context switch. But the sdhci_request() can not be
called in interrupt context when using host software queue for some host
drivers, due to the get_cd() ops can be sleepable.
But for some host drivers, such as Spreadtrum host driver, the card is
nonremovable, so the get_cd() ops is not sleepable, which means we can
complete the data request and trigger the next request in irq handler
to remove the context switch for the Spreadtrum host driver.
As suggested by Adrian, we should introduce a request_atomic() API to
indicate that a request can be called in interrupt context to remove
the context switch when using mmc host software queue. But this should
be done in another thread to convert the users of mmc host software queue.
Thus we can introduce a variable in struct sdhci_host to indicate that
we will always to defer to complete requests when using the host software
queue.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/e693e7a29beb3c1922b333f4603ea81f43d5c5b1.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add request_done ops for struct sdhci_ops as a preparation in case some
host controllers have different method to complete one request, such as
supporting request completion of MMC software queue.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/1539c801c8bbdbcd1d86f8c2dab375f5803c765a.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable the MMC host software queue for the SD card if the host controller
supports the MMC host software queue.
On my Spreadtrum platform, I did not see any obvious performance changes
in 4K block size when changing to use hsq for the SD cards, I think the
reason is the SD card works at a low speed on my platform, and most of
time is spent in the hardware. But we can see some obvious improvements
when enabling the packed request based on hsq, that's why we still add hsq
support for the SD cards.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/0065b4631fef2d61c3b89d14a4ea4f2b7499ea56.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now the MMC read/write stack will always wait for previous request is
completed by mmc_blk_rw_wait(), before sending a new request to hardware,
or queue a work to complete request, that will bring context switching
overhead and spend some extra time to poll the card for busy completion
for I/O writes via sending CMD13, especially for high I/O per second
rates, to affect the IO performance.
Thus this patch introduces MMC software queue interface based on the
hardware command queue engine's interfaces, which is similar with the
hardware command queue engine's idea, that can remove the context
switching. Moreover we set the default queue depth as 64 for software
queue, which allows more requests to be prepared, merged and inserted
into IO scheduler to improve performance, but we only allow 2 requests
in flight, that is enough to let the irq handler always trigger the
next request without a context switch, as well as avoiding a long latency.
Moreover the host controller should support HW busy detection for I/O
operations when enabling the host software queue. That means, the host
controller must not complete a data transfer request, until after the
card stops signals busy.
From the fio testing data in cover letter, we can see the software
queue can improve some performance with 4K block size, increasing
about 16% for random read, increasing about 90% for random write,
though no obvious improvement for sequential read and write.
Moreover we can expand the software queue interface to support MMC
packed request or packed command in future.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/4409c1586a9b3ed20d57ad2faf6c262fc3ccb6e2.1581478568.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC core with new 14lpp and later tech DLL should not enable
PWRSAVE_DLL since such controller's internal gating cannot meet
following MCLK requirement:
When MCLK is gated OFF, it is not gated for less than 0.5us and MCLK
must be switched on for at-least 1us before DATA starts coming.
Adding support for this requirement.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1581077075-26011-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes quirk which indicates a broken base clock. This was
making the kernel report wrong base clock of ~187MHz instead of 200MHz
even as the measurement on the hardware was showing 200MHz.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579602095-30060-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DLL resets are required while executing the auto tuning procedure in
ZynqMP. This patch adds code to support the same.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579602095-30060-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After various refactoring, we can populate the mmc_ops callbacks
directly and don't need to have wrappers for them anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-7-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TAPs are Renesas SDHI specific. Now that we moved all handling to the
SDHI core, we can also move the definitions from the TMIO struct to the
SDHI one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, select_tuning() is called after RPM resume. But
select_tuning() needs some additional function calls to work correctly.
Instead of reimplementing the whole postprocessing, just enforce
retuning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
check_scc_error() is too Renesas specific. Let's just call it
check_retune() to make it also easier understandable what it does.
Only a rename, no functional change.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the tap array in the driver is too low, this is not a warning but
an error. Also _once is not helpful, we should make sure it is
prominently in the logs. It is safe to do this because this will only
show up during SoC enablement when we a new SoCs needs more taps (if
that ever will happen).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move Renesas specific code for executing the tuning with a SCC into the
SDHI driver and leave only a generic call in the TMIO driver. Simplify
the code a little by removing init_tuning() and prepare_tuning()
callbacks. The latter is directly folded into the new execute_tuning()
callbacks.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use increasing BIT numbers consistently and remove some superfluous
comments.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191217114034.13290-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
HW engineers say that automatic tap correction cannot be used for HS400
in all R-Car Gen3 SoCs. So, check for that SDHI variant and disable it
when HS400 is about to be enabled.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191217114034.13290-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R-Car Gen3 cannot use correction error status with HS400.
HS200: CMD and DAT signal timing are based on CLK signal.
HS400: CMD signal is based on CLK. DAT signal is based on DS signal.
In HS400, CMD signal is 200MHz(SDR). DAT signal is 200MHz(DDR).
Center position of signal is different between CMD and DAT.
TAP position should be adjusted to the center position of CMD signal.
DAT sampling timing is adjusted by HS400 calibration circuit regardless
of TAP position. Refer to renesas_sdhi_adjust_hs400mode_enable().
However, correction error status contains CMD and DAT status in HS400
(DAT signal is not masked in HS400). Therefore, correction error status
cannot use in HS400. It means that auto correction cannot be uses in
HS400. Manual correction can change to the correct TAP position by
ignoring DAT correction error status and using only CMD correction
status.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: refactored patch from BSP]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191217114034.13290-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a manual correction mechanism for SDHI. Currently, SDHI
uses automatic TAP position correction. However, TAP position can also
be corrected manually via correction error status flags.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191217114034.13290-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
hw_reset() clears the automatic correction bit twice. I couldn't find
anything in the docs recommending that. Removing one of them didn't
cause any regressions here, so keep it simple.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191217114034.13290-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TX/RX register should not be treated the same way to allow for better
support of tuning. Fix this by using a default initial value for TX.
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200316025232.1167-1-ricky_wu@realtek.com
[Ulf: Updated changelog]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SAMA5D2x doesn't drive CMD line if GPIO is used as CD line (at least
SAMA5D27 doesn't). Fix this by forcing card-detect in the module
if module-controlled CD is not used.
Fixed commit addresses the problem only for non-removable cards. This
amends it to also cover gpio-cd case.
Cc: stable@vger.kernel.org
Fixes: 7a1e3f1431 ("mmc: sdhci-of-at91: force card detect value for non removable devices")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/8d10950d9940468577daef4772b82a071b204716.1584290561.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_PRESET_FOR_* registers are not set for the UniPhier platform
integration. (They are all read as zeros).
Set the SDHCI_QUIRK2_PRESET_VALUE_BROKEN quirk flag. Otherwise, the
High Speed DDR mode on the eMMC controller (MMC_TIMING_MMC_DDR52)
would not work.
I split the platform data to give no impact to other platforms,
although the UniPhier platform is currently only the upstream user
of this IP.
The SDHCI_QUIRK2_PRESET_VALUE_BROKEN flag is set if the compatible
string matches to "socionext,uniphier-sd4hc".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200312104257.21017-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On the Acer Aspire Switch 10 (SW5-012) microSD slot always reports the card
being write-protected even though microSD cards do not have a write-protect
switch at all.
Add a new DMI_QUIRK_SD_NO_WRITE_PROTECT quirk which when set sets
the MMC_CAP2_NO_WRITE_PROTECT flag on the controller for the external SD
slot; and add a DMI quirk table entry which selects this quirk for the
Acer SW5-012.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200316184753.393458-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on a sample of 7 DSDTs from Cherry Trail devices using an AXP288
PMIC depending on the design one of 2 possible LDOs on the PMIC is used
for the MMC signalling voltage, either DLDO3 or GPIO1LDO (GPIO1 pin in
low noise LDO mode).
The Lenovo Miix 320-10ICR uses GPIO1LDO in the SHC1 ACPI device's DSM
methods to set 3.3 or 1.8 signalling voltage and this appears to work
as advertised, so presumably the device is actually using GPIO1LDO for
the external microSD signalling voltage.
But this device has a bug in the _PS0 method of the SHC1 ACPI device,
the DSM remembers the last set signalling voltage and the _PS0 restores
this after a (runtime) suspend-resume cycle, but it "restores" the voltage
on DLDO3 instead of setting it on GPIO1LDO as the DSM method does. DLDO3
is used for the LCD and setting it to 1.8V causes the LCD to go black.
This commit works around this issue by calling the Intel DSM to reset the
signal voltage to 3.3V after the host has been runtime suspended.
This will make the _PS0 method reprogram the DLDO3 voltage to 3.3V, which
leaves it at its original setting fixing the LCD going black.
This commit adds and uses a DMI quirk mechanism to only trigger this
workaround on the Lenovo Miix 320 while leaving the behavior of the
driver unchanged on other devices.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=111294
BugLink: https://gitlab.freedesktop.org/drm/intel/issues/355
Reported-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200316184753.393458-1-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busy timeout for the CMD5 to put the eMMC into sleep state, is specific
to the card. Potentially the timeout may exceed the host->max_busy_timeout.
If that becomes the case, mmc_sleep() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200311092036.16084-1-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out that the sdhci-tegra controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.
Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.
Reported-by: Bitan Biswas <bbiswas@nvidia.com>
Reported-by: Peter Geis <pgwipeout@gmail.com>
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out that the sdhci-omap controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.
Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The busy timeout that is computed for each erase/trim/discard operation,
can become quite long and may thus exceed the host->max_busy_timeout. If
that becomes the case, mmc_do_erase() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has turned out that some host controllers can't use R1B for CMD6 and
other commands that have R1B associated with them. Therefore invent a new
host cap, MMC_CAP_NEED_RSP_BUSY to let them specify this.
In __mmc_switch(), let's check the flag and use it to prevent R1B responses
from being converted into R1. Note that, this also means that the host are
on its own, when it comes to manage the busy timeout.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable MSI interrupt for GL9750/GL9755. Some platforms
do not support PCI INTx and devices can not work without
interrupt. Like messages below:
[ 4.487132] sdhci-pci 0000:01:00.0: SDHCI controller found [17a0:9755] (rev 0)
[ 4.487198] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.PBR2._PRT.APS2], AE_NOT_FOUND (20190816/psargs-330)
[ 4.487397] ACPI Error: Aborting method \_SB.PCI0.PBR2._PRT due to previous error (AE_NOT_FOUND) (20190816/psparse-529)
[ 4.487707] pcieport 0000:00:01.3: can't derive routing for PCI INT A
[ 4.487709] sdhci-pci 0000:01:00.0: PCI INT A: no GSI
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200219092900.9151-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Call cpu_latency_qos_add/remove_request() instead of
pm_qos_add/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
This function is not exported and only used in this file. Mark it static.
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Cc: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Fixes: 87a8df0dce ("mmc: sdhci-msm: Add CQHCI support for sdhci-msm")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200206162124.201195-1-swboyd@chromium.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
All callers of __mmc_switch() should now be specifying a valid timeout for
the CMD6 command. However, just to be sure, let's print a warning and
default to use the generic_cmd6_time in case the provided timeout_ms
argument is zero.
In this context, let's also simplify some of the corresponding code and
clarify some related comments.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-4-ulf.hansson@linaro.org
The INAND_CMD38_ARG_EXT_CSD is a vendor specific EXT_CSD register, which is
used to prepare an erase/trim operation. However, it doesn't make sense to
use a timeout of 10 minutes while updating the register, which becomes the
case when the timeout_ms argument for mmc_switch() is set to zero.
Instead, let's use the generic_cmd6_time, as that seems like a reasonable
timeout to use for these cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-3-ulf.hansson@linaro.org
The timeout values used while waiting for a CMD6 for BKOPS or a CACHE_FLUSH
to complete, are not defined by the eMMC spec. However, a timeout of 10
minutes as is currently being used, is just silly for both of these cases.
Instead, let's specify more reasonable timeouts, 120s for BKOPS and 30s for
CACHE_FLUSH.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200122142747.5690-2-ulf.hansson@linaro.org
'static inline' in .c files does not make much sense because
functions may or may not be inlined irrespective of the 'inline'
marker. It is just a hint.
This function is quite small, so very likely to be inlined by the
compiler's optimization (-O2 or -Os), but it is up to the compiler
after all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200121105858.13325-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let a vendor driver supply the maximum descriptor size that it
can operate on. ADMA descriptor table would be allocated using this
supplied size.
If any SD Host controller is of version prior to v4.10 spec
but supports 16byte descriptor, this change allows them to supply
correct descriptor size for ADMA table allocation.
Also let a vendor driver update the descriptor size by overriding
sdhc_host->desc_size if it has to operates on a different descriptor
sizes in different conditions.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1579531122-28341-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to fix a serious issue that clock is always disabled
in esdhc_of_set_clock().
Fixes: 1b21a701ae ("mmc: sdhci-of-esdhc: fix clock setting for different controller versions")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200120094835.28050-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The standard SD controller uses two 16-bit registers for
command sending.
0xC: Transfer Mode Register
0xE: Command Register
But the eSDHC controller uses one 32-bit register instead.
0xC: XFERTYPE
For Transfer Mode Register and Command Register writing,
the eSDHC driver will store Transfer Mode Register value in
a variable first. When Command Register writing happens,
driver will directly write a 32-bit value into XFERTYPE
register.
But for Transfer Mode Register reading, driver just returns
a actual value. This may cause issue for some read-modify-write
operations. We should make both reading and write on that variable
for Transfer Mode Register.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200117063858.37296-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
This issue was previously fixed by commit c894e33ddc ("mmc: sdhci:
Fix incorrect switch to HS mode") and later removed by commit
07bcc41156 ("Revert \"mmc: sdhci: Fix incorrect switch to HS mode\"")
because it caused failures with some SD cards on AM65X systems. The
fix will now be done in a platform specific callback instead of
common sdhci code.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200113210706.11972-7-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shutdown controller and disable it's clocks to insure max power
savings in S5 on systems that leave power on.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-5-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The new SCMI clock protocol driver does not get probed that early in
boot. Brcmstb drivers typically have the following code when getting
a clock:
priv->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(priv->clk)) {
dev_err(&pdev->dev, "Clock not found in Device Tree\n");
priv->clk = NULL;
}
This commit changes the driver to do what is below.
priv->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(priv->clk)) {
if (PTR_ERR(priv->clk) == -EPROBE_DEFER)
return -EPROBE_DEFER;
dev_err(&pdev->dev, "Clock not found in Device Tree\n");
priv->clk = NULL;
}
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-4-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The latest eMMC JEDEC specification version 5.1 added a new
transfer mode, HS400 with enhanced strobe (HS400ES). This mode
will be selected if both the host controller and eMMC device
support it. The latest Arasan 5.1 controller in the 7216a0
supports this mode. The "Host Controller Specification" has
not been updated so the controller register bit used to enable
this mode is not specified and varies the with controller vendor.
The Linux SDHCI driver supplies a callback for enabling HS400ES
mode and that callback will be used to supply a routine that
will set the proper bit in the Arasan Vendor register.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20200113210706.11972-3-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116144322.57308-1-yuehaibing@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix an issue reported by sparse, since mixed types of parameters are
used on calling dmaengine_prep_slave_sg().
Fixes: 36e1da441fec (mmc: sdhci: add support for using external DMA devices)
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200120033223.897-1-zhang.chunyan@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDHCIv3+ with programmable clock mode, minimal clock frequency is
still base clock / max(divider). Minimal programmable clock frequency is
always greater than minimal divided clock frequency. Without this patch,
SDHCI uses out-of-spec initial frequency when multiplier is big enough:
mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz
[for 480 MHz source clock divided by 1024]
The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode.
Fixes: c3ed387762 ("mmc: sdhci: add support for programmable clock mode")
Cc: <stable@vger.kernel.org> # 4f6aa3264af4: mmc: tegra: Only advertise UHS modes if IO regulator is present
Cc: <stable@vger.kernel.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some omap controllers need software to monitor a 0->1->0 for software
reset. Add a SDHCI_OMAP_SPECIAL_RESET flag to indicate this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-11-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for new compatible for TI's am335x and am437x devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-10-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disable data timeout interrupt during an erase operation.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-8-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor sdhci_set_timeout() such that platform drivers can do some
functionality in a set_timeout() callback and then call
__sdhci_set_timeout() to complete the operation.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-7-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_set_timeout_irq() so that it is accessible from platform drivers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-omap can support both external dma controller via dmaengine framework
as well as ADMA which standard SD host controller provides.
Fixes by Faiz Abbas <fazi_abbas@ti.com>:
1. Switch to DMA slave mode when using external DMA
2. Add offset to mapbase
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-5-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some standard SD host controllers can support both external dma
controllers as well as ADMA/SDMA in which the SD host controller
acts as DMA master. TI's omap controller is the case as an example.
Currently the generic SDHCI code supports ADMA/SDMA integrated in
the host controller but does not have any support for external DMA
controllers implemented using dmaengine, meaning that custom code is
needed for any systems that use an external DMA controller with SDHCI.
Fixes by Faiz Abbas <faiz_abbas@ti.com>:
1. Map scatterlists before dmaengine_prep_slave_sg()
2. Use dma_async() functions inside of the send_command() path and call
terminate_sync() in non-atomic context in case of an error.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding external dma support, factor out data initialization,
block info and mrq_done to their own functions.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200116105154.7685-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_alloc_host() does its work not using managed infrastructure, so
needs explicit free on error path. Add it where needed.
Cc: <stable@vger.kernel.org>
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/b2a44d5be2e06ff075f32477e466598bb0f07b36.1577961679.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Command Queuing was enabled completely for J721e controllers which lead
to partial enablement even for Am65x. Complete CQ implementation for
AM65x by adding the irq callback.
Fixes: f545702b74 ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The tuning data is leftover in the buffer after tuning. This can cause
issues in future data commands, especially with CQHCI. Reset the command
and data lines after tuning to continue from a clean state.
Fixes: 41fd4caeb0 ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC/SD controllers on am65x and j721e don't in fact detect the write
protect line as inverted. No issues were detected because of this
because the sdwp line is not connected on any of the evms. Fix this by
removing the flag.
Fixes: 1accbced1c ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-2-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to fix clock setting code for different controller
versions. Two of HW changes after vendor version 2.2 are removing
PEREN/HCKEN/IPGEN bits in system control register, and adding SD
clock stable bit in present state register. This patch cleans up
related code too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200108040713.38888-2-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to fix operating in esdhc_reset() for different
controller versions, and to add bus-width restoring after data
reset for eSDHC (verdor version <= 2.2).
Also add annotation for understanding.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108040713.38888-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is an official update for eSDHC tuning erratum A-008171.
This patch is to implement the changes,
- Affect all revisions of SoC.
- Changes for tuning window checking.
- Hardware hits a new condition that tuning succeeds although
the eSDHC might not have tuned properly for type2 SoCs
(soc_tuning_erratum_type2[] array in driver). So check
tuning window after tuning succeeds.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191212075219.48625-2-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to use a new function esdhc_tuning_window_ptr() to
get tuning window start point and end point.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191212075219.48625-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191217122254.7103-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113114.32085-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113031.31847-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113004.31688-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112934.31535-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112847.31351-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112803.31161-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112737.31024-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112656.30860-1-peter.ujfalusi@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The erratum A-009204 workaround patch was reverted because of
incorrect implementation.
8b6dc6b mmc: sdhci-of-esdhc: Revert "mmc: sdhci-of-esdhc: add
erratum A-009204 support"
This patch is to re-implement the workaround (add a 5 ms delay
before setting SYSCTL[RSTD] to make sure all the DMA transfers
are finished).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20191219032335.26528-1-yangbo.lu@nxp.com
Fixes: 5dd1955225 ("mmc: sdhci-of-esdhc: add erratum A-009204 support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the ux500v2 variant of the PL18x block, any block sizes
are supported. This is necessary to support some SDIO
transfers. This also affects the QCOM MMCI variant and the
ST micro variant.
For Ux500 an additional quirk only allowing DMA on blocks
that are a power of two is needed. This might be a bug in
the DMA engine (DMA40) or the MMCI or in the interconnect,
but the most likely is the MMCI, as transfers of these
sizes work fine for other devices using the same DMA
engine. DMA works fine also with SDIO as long as the
blocksize is a power of 2.
This patch has proven necessary for enabling SDIO for WLAN on
PostmarketOS-based Ux500 platforms.
What we managed to test in practice is Broadcom WiFi over
SDIO on the Ux500 based Samsung GT-I8190 and GT-S7710.
This WiFi chip, BCM4334 works fine after the patch.
Before this patch:
brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4334-sdio
for chip BCM4334/3
mmci-pl18x 80118000.sdi1_per2: unsupported block size (60 bytes)
brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
brcmfmac: brcmf_sdio_download_code_file: error -22 on writing
434236 membytes at 0x00000000
brcmfmac: brcmf_sdio_download_firmware: dongle image file download
failed
After this patch:
brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4334/3 wl0:
Nov 21 2012 00:21:28 version 6.10.58.813 (B2) FWID 01-0
Bringing up networks, discovering networks with "iw dev wlan0 scan"
and connecting works fine from this point.
This patch is inspired by Ulf Hansson's patch
http://www.spinics.net/lists/linux-mmc/msg12160.html
As the DMA engines on these platforms may now get block sizes
they were not used to before, make sure to also respect if
the DMA engine says "no" to a transfer.
Make a drive-by fix for datactrl_blocksz, misspelled.
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191217143952.2885-1-linus.walleij@linaro.org
platform_get_resource(pdev, IORESOURCE_IRQ) is not recommended for
requesting IRQ's resources, as they can be not ready yet. Using
platform_get_irq() instead is preferred for getting IRQ even if it
was not retrieved earlier.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-13-tiny.windzz@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ludovic Barre