The clock driver is registered as platform devices and
it is possible to reloading the driver at runtime.
But actually the clocks should never be removed to make system work,
attempting to bind again would result in a crash, because almost all
devices depends on clock to function well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20211022131513.17381-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Some clocks shouldn't be automatically disabled in clk_disable_unused(),
otherwise kernel hangs. Mark those clocks with:
- CLK_IS_CRITICAL flag, when there won't be any consumers for that
clock, but system can't function when it's gated
- CLK_IGNORE_UNUSED flag, when consumer driver will be probably added
later
That makes it possible to run the kernel without passing the
"clk_ignore_unused" param.
Next clocks were modified:
- "gout_dpu_cmu_dpu_pclk": CLK_IGNORE_UNUSED
Will be enabled later in DSIM driver (Display Serial Interface
Master).
- "gout_gpio_peri_pclk": CLK_IGNORE_UNUSED
"gout_gpio_cmgp_pclk": CLK_IGNORE_UNUSED
"gout_gpio_hsi_pclk": CLK_IGNORE_UNUSED
Should be probably enabled in corresponding GPIO driver later, or
made CLK_IS_CRITICAL. "gout_gpio_peri_clk" is actually used by LEDs
on Exynos850-based dev board, so kernel hangs if this clock is not
running. Other clocks were marked as "ignore unused" to prevent
similar issues for other use cases or boards that might be added
later.
- "gout_cci_aclk": CLK_IS_CRITICAL
CCI (Cache Coherent Interconnect): obviously is critical.
- "gout_gic_clk": CLK_IS_CRITICAL
GIC (Generic Interrupt Controller): obviously is critical.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211121232741.6967-7-semen.protsenko@linaro.org
CMU_CMGP clock domain provides clocks for CMGP IP-core (Common GPIO).
CMGP module encapsulates next blocks:
- 8 GPIO lines
- 1 GPADC
- 2 USI blocks, each can be configured to provide one of
UART/SPI/HSI2C serial interfaces
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211121232741.6967-5-semen.protsenko@linaro.org
CMU_APM clock domain provides clocks for APM IP-core (Active Power
Management). According to Exynos850 TRM, CMU_APM generates I3C, Mailbox,
Speedy, Timer, WDT, RTC and PMU clocks for BLK_ALIVE.
This patch adds next clocks:
- bus clocks in CMU_TOP needed for CMU_APM
- all internal CMU_APM clocks
- leaf clocks for I3C, Speedy and RTC IP-cores
- bus clocks for CMU_CMGP and CMU_CHUB
CMU_APM doesn't belong to Power Domains, but platform driver is used for
its registration to keep its bus clock always running. Otherwise rtc-s3c
driver disables that clock and system freezes.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211121232741.6967-3-semen.protsenko@linaro.org
While it is useful to build all of the CCU drivers at once, only 1-3 of
them will be loaded at a time, or possibly none of them if the kernel is
booted on a non-sunxi platform. These CCU drivers are relatively large;
32-bit drivers have 30-50k of data each, while the 64-bit ones are
50-75k due to the increased pointer overhead. About half of that data
comes from relocations. Let's allow the user to build these drivers as
modules so only the necessary data is loaded.
As a first step, convert the CCUs that are already platform drivers.
When the drivers are built as modules, normally the file name becomes
the module name. However, the current file names are inconsistent with
the <platform>-<peripheral> name used everywhere else: the devicetree
bindings, the platform driver names, and the Kconfig symbols. Use
Makfile logic to rename the modules so they follow the usual pattern.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211119033338.25486-3-samuel@sholland.org
For the individual CCU drivers to be built as modules, the ops structs,
helper functions, and callback registration functions must be exported.
These symbols are intended for use only by the adjacent CCU drivers, so
export them into the SUNXI_CCU namespace.
of_sunxi_ccu_probe is not exported because it is only used by built-in
OF clock providers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211119033338.25486-2-samuel@sholland.org
Convert the remaining exynos clock drivers to use
samsung_clk_register_cpu() or if possible use samsung_cmu_register_one().
With this we can now make exynos_register_cpu_clock() a static function
so that future CPU clock registration changes will use the samsung common
clock driver.
The main benefit of this change is that it standardizes the CPU clock
registration for the samsung clock drivers.
Link: https://lore.kernel.org/r/20211015190515.3760577-1-willmcvicker@google.com
Signed-off-by: Will McVicker <willmcvicker@google.com>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
[snawrocki@kernel.org: Fixed build break in clk-exynos4.c, clk-exynos5250.c]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Remove useless __init atrribute and unneeded extern qualifier in function
declarations in header files.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20211015151425.29743-1-s.nawrocki@samsung.com
__clk_lookup() interface is obsolete, so remove it from the Samsung clock
drivers. This has been achieved by getting rid of custom _get_rate()
helper and replacing it with clk_hw_get_rate().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211018125456.8292-2-m.szyprowski@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
of_genpd_add_provider_simple() might fail, this patch makes sure we check
the return value of of_genpd_add_provider_simple() by propagating the
return value to the caller of cpg_mssr_add_clk_domain().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make sure we check the return value of pm_genpd_init() which might fail.
Also add a devres action to remove the power-domain in-case the probe
callback fails further down in the code flow.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
of_genpd_add_provider_simple() might fail, this patch makes sure we check
the return value of of_genpd_add_provider_simple() by propagating the
return value to the caller of rzg2l_cpg_add_clk_domain().
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Make sure we check the return value of pm_genpd_init() which might fail.
Also add a devres action to remove the power-domain in-case the probe
callback fails further down in the code flow.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211117115101.28281-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV divider as per HW manual
Rev.1.00.
This patch adds clock divider table "dtable_1_8" and switches to
DEF_DIV for "I" clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV which controls CPU
frequency. Define CPG_PL1_DDIV, so that we can register it as a
clock divider in later patch.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The old SD handling code was huge and could not handle all the details
which showed up on R-Car Gen3 SoCs meanwhile. It is time to switch to
another design. Have SDnH a separate clock, use the existing divider
clocks and move the errata handling from the clock driver to the SDHI
driver where it belongs.
This patch removes the old SD handling code and switch to the new one.
This updates the SDHI driver at the same time. Because the SDHI driver
can only communicate with the clock driver via clk_set_rate(), I don't
see an alternative to this flag-day-approach, so we cross subsystems
here.
The patch sadly looks messy for the CPG lib, but it is basically a huge
chunk of code removed and smaller chunks added. It looks much better
when you just view the resulting source file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Link: https://lore.kernel.org/r/20211110191610.5664-6-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently, SDnH is handled together with SDn. This caused lots of
problems, so we want SDnH as a separate clock. Introduce a dummy SDnH
type here which creates a fixed-factor clock with factor 1. That allows
us to convert the per-SoC CPG drivers while keeping the old behaviour
for now. A later patch then will add the proper functionality.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211110191610.5664-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macros CLK_PLL2_DIV16->CLK_PLL2_DIV2_8 and
CLK_PLL2_DIV20->CLK_PLL2_DIV2_10 to match the clock tree mentioned in
the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110082019.28554-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
make W=1:
drivers/clk/renesas/rzg2l-cpg.c:95: warning: Function parameter or member 'num_resets' not described in 'rzg2l_cpg_priv'
Add the missing kerneldoc for fields in struct rzg2l_cpg_priv and struct
rzg2l_cpg_info related to Module Resets.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/39c2c5fd4232b6620a4a56dba4e2b0d61476ee36.1634646869.git.geert+renesas@glider.be
- 2 fixes due to DT node name changes on Arm, Ltd. boards
- Treewide rename of Ingenic CGU headers
- Update ST email addresses
- Remove Netlogic DT bindings
- Dropping few more cases of redundant 'maxItems' in schemas
- Convert toshiba,tc358767 bridge binding to schema
-----BEGIN PGP SIGNATURE-----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=ukBC
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Two fixes due to DT node name changes on Arm, Ltd. boards
- Treewide rename of Ingenic CGU headers
- Update ST email addresses
- Remove Netlogic DT bindings
- Dropping few more cases of redundant 'maxItems' in schemas
- Convert toshiba,tc358767 bridge binding to schema
* tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: watchdog: sunxi: fix error in schema
bindings: media: venus: Drop redundant maxItems for power-domain-names
dt-bindings: Remove Netlogic bindings
clk: versatile: clk-icst: Ensure clock names are unique
of: Support using 'mask' in making device bus id
dt-bindings: treewide: Update @st.com email address to @foss.st.com
dt-bindings: media: Update maintainers for st,stm32-hwspinlock.yaml
dt-bindings: media: Update maintainers for st,stm32-cec.yaml
dt-bindings: mfd: timers: Update maintainers for st,stm32-timers
dt-bindings: timer: Update maintainers for st,stm32-timer
dt-bindings: i2c: imx: hardware do not restrict clock-frequency to only 100 and 400 kHz
dt-bindings: display: bridge: Convert toshiba,tc358767.txt to yaml
dt-bindings: Rename Ingenic CGU headers to ingenic,*.h
a little more time to soak in linux-next.
- Use modern i2c probe in vc5
- Cleanup some includes
- Update links to datasheets
- Add UniPhier NX1 SoC clk support
- Fix DT bindings for SiFive FU740
- Revert the module platform driver support for Rockchip out
because it wasn't actually tested
- Fix the composite clk code again as the previous fix had a
one line bug that broke rate changes for clks that want to use
the same parent still
- Use the right table for a divider in ast2600 driver
- Get rid of gcc_aggre1_pnoc_ahb_clk in qcom clk driver again because
its critical but unused
-----BEGIN PGP SIGNATURE-----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=j1rC
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
"This is the second batch of clk driver updates that needed a little
more time to soak in linux-next.
- Use modern i2c probe in vc5
- Cleanup some includes
- Update links to datasheets
- Add UniPhier NX1 SoC clk support
- Fix DT bindings for SiFive FU740
- Revert the module platform driver support for Rockchip because it
wasn't actually tested
- Fix the composite clk code again as the previous fix had a one line
bug that broke rate changes for clks that want to use the same
parent still
- Use the right table for a divider in ast2600 driver
- Get rid of gcc_aggre1_pnoc_ahb_clk in qcom clk driver again because
its critical but unused"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc-msm8996: Drop (again) gcc_aggre1_pnoc_ahb_clk
clk: imx8m: Do not set IMX_COMPOSITE_CORE for non-regular composites
clk/ast2600: Fix soc revision for AHB
clk: composite: Fix 'switching' to same clock
clk: rockchip: drop module parts from rk3399 and rk3568 drivers
Revert "clk: rockchip: use module_platform_driver_probe"
clk:mediatek: remove duplicate include in clk-mt8195-imp_iic_wrap.c
dt-bindings: clock: fu740-prci: add reset-cells
clk: uniphier: Add SoC-glue clock source selector support for Pro4
dt-bindings: clock: uniphier: Add clock binding for SoC-glue
clk: uniphier: Add NX1 clock support
dt-bindings: clock: uniphier: Add NX1 clock binding
clk: uniphier: Add audio system and video input clock control for PXs3
clk: si5351: Update datasheet references
clk: vc5: Use i2c .probe_new
clk/actions/owl-factor.c: remove superfluous headers
clk: ingenic: Fix bugs with divided dividers
Commit 2d3de197a8 ("ARM: dts: arm: Update ICST clock nodes 'reg' and
node names") moved to using generic node names. That results in trying
to register multiple clocks with the same name. Fix this by including
the unit-address in the clock name.
Fixes: 2d3de197a8 ("ARM: dts: arm: Update ICST clock nodes 'reg' and node names")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211109164650.2233507-3-robh@kernel.org
Tidy up a bit the tree, by prefixing all include/dt-bindings/clock/ files
related to Ingenic SoCs with 'ingenic,'.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211016133322.40771-1-paul@crapouillou.net
- Remove support for TI TPS80031/TPS80032 PMICs
- New Device Support
- Add support for Magnetic Reader to TI AM335x
- Add support for DA9063_EA to Dialog DA9063
- Add support for SC2730 PMIC to Spreadtrum SC27xx
- Add support for MacBookPro16,2 ICL-N UART Intel LPSS PCI
- Add support for lots of new PMICS in QCom SPMI PMIC
- Add support for ADC to Diolan DLN2
- New Functionality
- Add support for Power Off to Rockchip RK817
- Fix-ups
- Simplify Regmap passing to child devices; hi6421-spmi-pmic
- SPDX licensing updates; ti_am335x_tscadc
- Improve error handling; ti_am335x_tscadc
- Expedite clock search; ti_am335x_tscadc
- Generic simplifications; ti_am335x_tscadc
- Use generic macros/defines; ti_am335x_tscadc
- Remove unused code; ti_am335x_tscadc, cros_ec_dev
- Convert to GPIOD; wcd934x
- Add namespacing; ti_am335x_tscadc
- Restrict compilation to relevant arches; intel_pmt
- Provide better description/documentation; exynos_lpass
- Add SPI device ID table; altera-a10sr, motorola-cpcap, sprd-sc27xx-spi
- Change IRQ handling; qcom-pm8xxx
- Split out I2C and SPI code; arizona
- Explicitly include used headers; altera-a10sr
- Convert sysfs show() function to; sysfs_emit
- Standardise *_exit() and *_remove() return values; mc13xxx, stmpe, tps65912
- Trivial (style/spelling/whitespace) fixups; ti_am335x_tscadc, qcom-spmi-pmic,
max77686-private
- Device Tree fix-ups; ti,am3359-tscadc, samsung,s2mps11, samsung,s2mpa01,
samsung,s5m8767, brcm,misc, brcm,cru, syscon, qcom,tcsr,
xylon,logicvc, max77686, x-powers,ac100, x-powers,axp152,
x-powers,axp209-gpio, syscon, qcom,spmi-pmic
- Bug Fixes
- Balance refcounting (get/put); ti_am335x_tscadc, mfd-core
- Fix IRQ trigger type; sec-irq, max77693, max14577
- Repair off-by-one; altera-sysmgr
- Add explicit 'select MFD_CORE' to MFD_SIMPLE_MFD_I2C
-----BEGIN PGP SIGNATURE-----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=SJ7N
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Removed Drivers:
- Remove support for TI TPS80031/TPS80032 PMICs
New Device Support:
- Add support for Magnetic Reader to TI AM335x
- Add support for DA9063_EA to Dialog DA9063
- Add support for SC2730 PMIC to Spreadtrum SC27xx
- Add support for MacBookPro16,2 ICL-N UART Intel LPSS PCI
- Add support for lots of new PMICS in QCom SPMI PMIC
- Add support for ADC to Diolan DLN2
New Functionality:
- Add support for Power Off to Rockchip RK817
Fix-ups:
- Simplify Regmap passing to child devices in hi6421-spmi-pmic
- SPDX licensing updates in ti_am335x_tscadc
- Improve error handling in ti_am335x_tscadc
- Expedite clock search in ti_am335x_tscadc
- Generic simplifications in ti_am335x_tscadc
- Use generic macros/defines in ti_am335x_tscadc
- Remove unused code in ti_am335x_tscadc, cros_ec_dev
- Convert to GPIOD in wcd934x
- Add namespacing in ti_am335x_tscadc
- Restrict compilation to relevant arches in intel_pmt
- Provide better description/documentation in exynos_lpass
- Add SPI device ID table in altera-a10sr, motorola-cpcap,
sprd-sc27xx-spi
- Change IRQ handling in qcom-pm8xxx
- Split out I2C and SPI code in arizona
- Explicitly include used headers in altera-a10sr
- Convert sysfs show() function to in sysfs_emit
- Standardise *_exit() and *_remove() return values in mc13xxx,
stmpe, tps65912
- Trivial (style/spelling/whitespace) fixups in ti_am335x_tscadc,
qcom-spmi-pmic, max77686-private
- Device Tree fix-ups in ti,am3359-tscadc, samsung,s2mps11,
samsung,s2mpa01, samsung,s5m8767, brcm,misc, brcm,cru, syscon,
qcom,tcsr, xylon,logicvc, max77686, x-powers,ac100,
x-powers,axp152, x-powers,axp209-gpio, syscon, qcom,spmi-pmic
Bug Fixes:
- Balance refcounting (get/put) in ti_am335x_tscadc, mfd-core
- Fix IRQ trigger type in sec-irq, max77693, max14577
- Repair off-by-one in altera-sysmgr
- Add explicit 'select MFD_CORE' to MFD_SIMPLE_MFD_I2C"
* tag 'mfd-next-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (95 commits)
mfd: simple-mfd-i2c: Select MFD_CORE to fix build error
mfd: tps80031: Remove driver
mfd: max77686: Correct tab-based alignment of register addresses
mfd: wcd934x: Replace legacy gpio interface for gpiod
dt-bindings: mfd: qcom: pm8xxx: Add pm8018 compatible
mfd: dln2: Add cell for initializing DLN2 ADC
mfd: qcom-spmi-pmic: Add missing PMICs supported by socinfo
mfd: qcom-spmi-pmic: Document ten more PMICs in the binding
mfd: qcom-spmi-pmic: Sort compatibles in the driver
mfd: qcom-spmi-pmic: Sort the compatibles in the binding
mfd: janz-cmoio: Replace snprintf in show functions with sysfs_emit
mfd: altera-a10sr: Include linux/module.h
mfd: tps65912: Make tps65912_device_exit() return void
mfd: stmpe: Make stmpe_remove() return void
mfd: mc13xxx: Make mc13xxx_common_exit() return void
dt-bindings: mfd: syscon: Add samsung,exynosautov9-sysreg compatible
mfd: altera-sysmgr: Fix a mistake caused by resource_size conversion
dt-bindings: gpio: Convert X-Powers AXP209 GPIO binding to a schema
dt-bindings: mfd: syscon: Add rk3368 QoS register compatible
mfd: arizona: Split of_match table into I2C and SPI versions
...
The gcc_aggre1_pnoc_ahb_clk is crucial for the proper MSM8996/APQ8096
functioning. If it gets disabled, several subsytems will stop working
(including eMMC/SDCC and USB). There are no in-kernel users of this
clock, so it is much simpler to remove from the kernel.
The clock was first removed in the commit 9e60de1cf2 ("clk: qcom:
Remove gcc_aggre1_pnoc_ahb_clk from msm8996") by Stephen Boyd, but got
added back in the commit b567752144 ("clk: qcom: Add some missing gcc
clks for msm8996") by Rajendra Nayak.
Let's remove it again in hope that nobody adds it back.
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Fixes: b567752144 ("clk: qcom: Add some missing gcc clks for msm8996")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211104011155.2209654-1-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Only imx8m_clk_hw_composite_core needs to set this flag.
Fixes: a60fe746df ("clk: imx: Rework all imx_clk_hw_composite wrappers")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211103123947.3222443-1-alexander.stein@ew.tq-group.com
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
terms of lines it's mainly Qualcomm and Mediatek code, supporting
various SoCs and their multitude of clk controllers.
New Drivers:
- GCC and RPMcc support for Qualcomm QCM2290 SoCs
- GCC support for Qualcomm MSM8994/MSM8992 SoCs
- LPASSCC and CAMCC support for Qualcomm SC7280 SoCs
- Support for Mediatek MT8195 SoCs
- Initial clock driver for the Exynos850 SoC
- Add i.MX8ULP clock driver and related bindings
Updates:
- Clock power management for new SAMA7G5 SoC
- Updates to the master clock driver and sam9x60-pll to be able to use
cpufreq-dt driver and avoid overclocking of CPU and MCK0 domains while
changing the frequency via DVFS
- Use ARRAY_SIZE in qcom clk drivers
- Remove some impractical fallback parent names in qcom clk drivers
- Make Mediatek clk drivers tristate
- Refactoring of the CPU clock code and conversion of Samsung Exynos5433
CPU clock driver to the platform driver
- A few conversions to devm_platform_ioremap_resource()
- Updates of the Samsung Kconfig help text
- Update video path realted clocks for Amlogic meson8
- Add SPI Multi I/O Bus and SDHI clocks and resets on Renesas RZ/G2L
- Add SPI Multi I/O Bus (RPC) clocks on Renesas R-Car V3U
- Add MediaLB clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Remove unused helpers from i.MX specific clock header
- Rework all i.MX clk based helpers to use clk_hw based ones
- Rework i.MX gate/mux/divider wrappers
- Rework imx_clk_hw_composite and imx_clk_hw_pll14xx wrappers
- Update i.MX pllv4 and composite clocks to support i.MX8ULP
- Disable i.MX7ULP composite clock during initialization
- Add CLK_SET_RATE_NO_REPARENT flag to the i.MX7ULP composite
- Disable the i.MX pfd when set pfdv2 clock rate
- Add support for i.MX8ULP in pfdv2
- Add the pcc reset controller support on i.MX8ULP
- Fix the build break when clk-imx8ulp is built as module
- Move csi_sel mux to correct base register in i.MX6UL clock drivr
- Fix csi clk gate register in i.MX6UL clock driver
- Fix build bug making CLK_IMX8ULP select MXC_CLK
- Add TPU (PWM), and Z (Cortex-A76) clocks on Renesas R-Car V3U
- Add Ethernet clocks on Renesas RZ/G2L
- Move Rockchip to use module_platform_probe
- Enable usage of Coresight related clocks on Rockchip rk3399
-----BEGIN PGP SIGNATURE-----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=Is+O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of clk driver updates and new driver additions.
In terms of lines it's mainly Qualcomm and Mediatek code, supporting
various SoCs and their multitude of clk controllers.
New Drivers:
- GCC and RPMcc support for Qualcomm QCM2290 SoCs
- GCC support for Qualcomm MSM8994/MSM8992 SoCs
- LPASSCC and CAMCC support for Qualcomm SC7280 SoCs
- Support for Mediatek MT8195 SoCs
- Initial clock driver for the Exynos850 SoC
- Add i.MX8ULP clock driver and related bindings
Updates:
- Clock power management for new SAMA7G5 SoC
- Updates to the master clock driver and sam9x60-pll to be able to
use cpufreq-dt driver and avoid overclocking of CPU and MCK0
domains while changing the frequency via DVFS
- Use ARRAY_SIZE in qcom clk drivers
- Remove some impractical fallback parent names in qcom clk drivers
- Make Mediatek clk drivers tristate
- Refactoring of the CPU clock code and conversion of Samsung
Exynos5433 CPU clock driver to the platform driver
- A few conversions to devm_platform_ioremap_resource()
- Updates of the Samsung Kconfig help text
- Update video path realted clocks for Amlogic meson8
- Add SPI Multi I/O Bus and SDHI clocks and resets on Renesas RZ/G2L
- Add SPI Multi I/O Bus (RPC) clocks on Renesas R-Car V3U
- Add MediaLB clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Remove unused helpers from i.MX specific clock header
- Rework all i.MX clk based helpers to use clk_hw based ones
- Rework i.MX gate/mux/divider wrappers
- Rework imx_clk_hw_composite and imx_clk_hw_pll14xx wrappers
- Update i.MX pllv4 and composite clocks to support i.MX8ULP
- Disable i.MX7ULP composite clock during initialization
- Add CLK_SET_RATE_NO_REPARENT flag to the i.MX7ULP composite
- Disable the i.MX pfd when set pfdv2 clock rate
- Add support for i.MX8ULP in pfdv2
- Add the pcc reset controller support on i.MX8ULP
- Fix the build break when clk-imx8ulp is built as module
- Move csi_sel mux to correct base register in i.MX6UL clock drivr
- Fix csi clk gate register in i.MX6UL clock driver
- Fix build bug making CLK_IMX8ULP select MXC_CLK
- Add TPU (PWM), and Z (Cortex-A76) clocks on Renesas R-Car V3U
- Add Ethernet clocks on Renesas RZ/G2L
- Move Rockchip to use module_platform_probe
- Enable usage of Coresight related clocks on Rockchip rk3399"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (170 commits)
clk: use clk_core_get_rate_recalc() in clk_rate_get()
clk: at91: sama7g5: set low limit for mck0 at 32KHz
clk: at91: sama7g5: remove prescaler part of master clock
clk: at91: clk-master: add notifier for divider
clk: at91: clk-sam9x60-pll: add notifier for div part of PLL
clk: at91: clk-master: fix prescaler logic
clk: at91: clk-master: mask mckr against layout->mask
clk: at91: clk-master: check if div or pres is zero
clk: at91: sam9x60-pll: use DIV_ROUND_CLOSEST_ULL
clk: at91: pmc: add sama7g5 to the list of available pmcs
clk: at91: clk-master: improve readability by using local variables
clk: at91: clk-master: add register definition for sama7g5's master clock
clk: at91: sama7g5: add securam's peripheral clock
clk: at91: pmc: execute suspend/resume only for backup mode
clk: at91: re-factor clocks suspend/resume
clk: ux500: Add driver for the reset portions of PRCC
dt-bindings: clock: u8500: Rewrite in YAML and extend
clk: composite: Use rate_ops.determine_rate when also a mux is available
clk: samsung: describe drivers in Kconfig
clk: samsung: exynos5433: update apollo and atlas clock probing
...
Move the soc revision parsing to the initial probe, saving the driver
from parsing the register multiple times.
Use this variable to select the correct divisor table for the AHB clock.
Before this fix the A2 would have used the A0 table.
Fixes: 2d491066cc ("clk: ast2600: Fix AHB clock divider for A1")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210922235449.213631-1-joel@jms.id.au
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
During commit 6594988fd6 ("clk: composite: Use rate_ops.determine_rate
when also a mux is available") setting req->best_parent_hw got lost,
so best_parent_hw stays NULL during switch to the same parent. This
results in the (debug) message:
clk_calc_new_rates: lcdif_pixel not gated but wants to reparent
and the following rate change is dropped.
Fixes: 6594988fd6 ("clk: composite: Use rate_ops.determine_rate when also a mux is available")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211103122441.3208576-1-alexander.stein@ew.tq-group.com
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Both of these drivers were converted to real drivers and got a tristate
build option. But them being builtin_platform_drivers, they only ever
should be build-in - as the name suggests.
So adapt the Kconfig symbol and drop the MODULE_* parts from the drivers.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20211027132616.1039814-3-heiko@sntech.de
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This reverts commit 1da80da028.
Reading recent discussions [0] [1], I realized this change introduces
a number of problems:
- only converting to module_platform_driver creates the issue
with the existing __init and __initdata attributes.
When the driver would've been built as a module, all the missing
clock-definitions (all are initdata) should've turned up as error
in testing suggesting that the change wasn't at all
- a clock driver is a very core component of soc bringup and making
this able to be built as a module solely for enabling the soc vendor
to add out of tree changes for Android implementations is not in our
interest and also everything except a ramdisk won't probe without a
clock controller.
This is especially true when the changes aren't really tested and
are merely added to move the mainline driver "out of the way".
[0] https://lwn.net/Articles/872209/
[1] https://lore.kernel.org/all/163529604399.15791.378104318036812951@swboyd.mtv.corp.google.com/
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20211027132616.1039814-2-heiko@sntech.de
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
'dt-bindings/clock/mt8195-clk.h' included in
'/drivers/clk/mediatek/clk-mt8195-imp_iic_wrap.c' is duplicated.It is
also included on the 13 line.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ran Jianping <ran.jianping@zte.com.cn>
Link: https://lore.kernel.org/r/20211019062939.979660-1-ran.jianping@zte.com.cn
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add basic clock data for UniPhier NX1 SoC.
This includes PLL and clock division data for cpufreq support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1634000035-3114-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Silicon Labs is now part of Skyworks Inc. so update the URLs to the
datasheet and application note.
Signed-off-by: Jens Renner <renner@efe-gmbh.de>
Link: https://lore.kernel.org/r/20210913074823.115212-1-renner@efe-gmbh.de
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
owl-factor.c hasn't use any macro or function declared in linux/slab.h.
Thus, these files can be removed from owl-factor.c safely without
affecting the compilation of the ./drivers/clk module
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Link: https://lore.kernel.org/r/20210929065824.23691-1-liumh1@shanghaitech.edu.cn
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Two fixes in one:
- In the "impose hardware constraints" block, the "logical" divider
value (aka. not translated to the hardware) was clamped to fit in the
register area, but this totally ignored the fact that the divider
value can itself have a fixed divider.
- The code that made sure that the divider value returned by the
function was a multiple of its own fixed divider could result in a
wrong value being calculated, because it was rounded down instead of
rounded up.
Fixes: 4afe2d1a6e ("clk: ingenic: Allow divider value to be divided")
Co-developed-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211001172033.122329-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-composite-determine-fix:
clk: composite: Use rate_ops.determine_rate when also a mux is available
clk: composite: Also consider .determine_rate for rate + mux composites
* clk-allwinner:
clk: sunxi: sun8i-apb0: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi: sun6i-ar100: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi: sun6i-apb0-gates: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi: sun6i-apb0: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi-ng: ccu-sun9i-a80-usb: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi-ng: ccu-sun9i-a80-de: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi-ng: ccu-sun9i-a80: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi-ng: ccu-sun8i-r40: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi-ng: ccu-sun8i-de2: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi-ng: ccu-sun8i-a83t: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi-ng: ccu-sun50i-h6: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi-ng: ccu-sun50i-a64: Make use of the helper function devm_platform_ioremap_resource()
clk: sunxi: clk-mod0: Make use of the helper function devm_platform_ioremap_resource()
dt-bindings: clocks: Fix typo in the H6 compatible
clk: sunxi-ng: Use a separate lock for each CCU instance
clk: sunxi-ng: Prevent unbinding CCUs via sysfs
clk: sunxi-ng: Unregister clocks/resets when unbinding
clk: sunxi-ng: Add machine dependency to A83T CCU
clk: sunxi-ng: mux: Remove unused 'reg' field
* clk-amlogic:
clk: meson: meson8b: Make the video clock trees mutable
clk: meson: meson8b: Initialize the HDMI PLL registers
clk: meson: meson8b: Add the HDMI PLL M/N parameters
clk: meson: meson8b: Add the vid_pll_lvds_en gate clock
clk: meson: meson8b: Use CLK_SET_RATE_NO_REPARENT for vclk{,2}_in_sel
clk: meson: meson8b: Export the video clocks
* clk-samsung:
clk: samsung: describe drivers in Kconfig
clk: samsung: exynos5433: update apollo and atlas clock probing
clk: samsung: add support for CPU clocks
clk: samsung: Introduce Exynos850 clock driver
dt-bindings: clock: Document Exynos850 CMU bindings
dt-bindings: clock: Add bindings definitions for Exynos850 CMU
clk: samsung: clk-pll: Implement pll0831x PLL type
clk: samsung: clk-pll: Implement pll0822x PLL type
clk: samsung: s5pv210-audss: Make use of devm_platform_ioremap_resource()
clk: samsung: exynos5433: Make use of devm_platform_ioremap_resource()
clk: samsung: exynos4412-isp: Make use of devm_platform_ioremap_resource()
clk: samsung: exynos-audss: Make use of devm_platform_ioremap_resource()
* clk-imx: (21 commits)
clk: imx: Make CLK_IMX8ULP select MXC_CLK
clk: imx: imx6ul: Fix csi clk gate register
clk: imx: imx6ul: Move csi_sel mux to correct base register
clk: imx: Fix the build break when clk-imx8ulp build as module
clk: imx: Add the pcc reset controller support on imx8ulp
clk: imx: Add clock driver for imx8ulp
clk: imx: Update the pfdv2 for 8ulp specific support
clk: imx: disable the pfd when set pfdv2 clock rate
clk: imx: Add 'CLK_SET_RATE_NO_REPARENT' for composite-7ulp
clk: imx: disable i.mx7ulp composite clock during initialization
clk: imx: Update the compsite driver to support imx8ulp
clk: imx: Update the pllv4 to support imx8ulp
dt-bindings: clock: Add imx8ulp clock support
clk: imx: Rework imx_clk_hw_pll14xx wrapper
clk: imx: Rework all imx_clk_hw_composite wrappers
clk: imx: Rework all clk_hw_register_divider wrappers
clk: imx: Rework all clk_hw_register_mux wrappers
clk: imx: Rework all clk_hw_register_gate2 wrappers
clk: imx: Rework all clk_hw_register_gate wrappers
clk: imx: Make mux/mux2 clk based helpers use clk_hw based ones
...
* clk-ux500:
clk: ux500: Add driver for the reset portions of PRCC
dt-bindings: clock: u8500: Rewrite in YAML and extend
* clk-debugfs:
clk: use clk_core_get_rate_recalc() in clk_rate_get()
- Clock power management for new SAMA7G5 SoC
- Updates to the master clock driver and sam9x60-pll to be able to use
cpufreq-dt driver and avoid overclocking of CPU and MCK0 domains while
changing the frequency via DVFS
- Power management refinement with the use of save_context()/restore_context()
on each clock driver to specify their use in case of Backup mode only
* clk-leak:
clk: mvebu: ap-cpu-clk: Fix a memory leak in error handling paths
* clk-rockchip:
clk: rockchip: use module_platform_driver_probe
clk: rockchip: rk3399: expose PCLK_COREDBG_{B,L}
clk: rockchip: rk3399: make CPU clocks critical
* clk-renesas:
clk: renesas: r8a779[56]x: Add MLP clocks
clk: renesas: r9a07g044: Add SDHI clock and reset entries
clk: renesas: rzg2l: Add SDHI clk mux support
clk: renesas: r8a779a0: Add RPC support
clk: renesas: cpg-lib: Move RPC clock registration to the library
clk: renesas: r9a07g044: Add clock and reset entries for SPI Multi I/O Bus Controller
clk: renesas: r8a779a0: Add Z0 and Z1 clock support
clk: renesas: r9a07g044: Add GbEthernet clock/reset
clk: renesas: rzg2l: Add support to handle coupled clocks
clk: renesas: r9a07g044: Add ethernet clock sources
clk: renesas: rzg2l: Add support to handle MUX clocks
clk: renesas: r8a779a0: Add TPU clock
clk: renesas: rzg2l: Fix clk status function
clk: renesas: r9a07g044: Mark IA55_CLK and DMAC_ACLK critical
* clk-at91:
clk: at91: sama7g5: set low limit for mck0 at 32KHz
clk: at91: sama7g5: remove prescaler part of master clock
clk: at91: clk-master: add notifier for divider
clk: at91: clk-sam9x60-pll: add notifier for div part of PLL
clk: at91: clk-master: fix prescaler logic
clk: at91: clk-master: mask mckr against layout->mask
clk: at91: clk-master: check if div or pres is zero
clk: at91: sam9x60-pll: use DIV_ROUND_CLOSEST_ULL
clk: at91: pmc: add sama7g5 to the list of available pmcs
clk: at91: clk-master: improve readability by using local variables
clk: at91: clk-master: add register definition for sama7g5's master clock
clk: at91: sama7g5: add securam's peripheral clock
clk: at91: pmc: execute suspend/resume only for backup mode
clk: at91: re-factor clocks suspend/resume
clk: at91: check pmc node status before registering syscore ops
to use the determine_rate instead of round_rate clk op by default. This
caused lots of problems on Rockchip SoCs because they heavily use
the composite clk code to model the clk tree.
-----BEGIN PGP SIGNATURE-----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=5b/O
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for the composite clk that broke when we changed this clk type
to use the determine_rate instead of round_rate clk op by default.
This caused lots of problems on Rockchip SoCs because they heavily use
the composite clk code to model the clk tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: composite: Also consider .determine_rate for rate + mux composites
In case clock flags contains CLK_GET_RATE_NOCACHE the clk_rate_get()
will return the cached rate. Thus, use clk_core_get_rate_recalc() which
takes proper action when clock flags contains CLK_GET_RATE_NOCACHE.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-16-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[sboyd@kernel.org: Grab prepare lock around operation]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On SAMA7G5 the prescaler part of master clock has been implemented as a
changeable one. Everytime the prescaler is changed the PMC_SR.MCKRDY bit
must be polled. Value 1 for PMC_SR.MCKRDY means the prescaler update is
done. Driver polls for this bit until it becomes 1. On SAMA7G5 it has
been discovered that in some conditions the PMC_SR.MCKRDY is not rising
but the rate it provides it's stable. The workaround is to add a timeout
when polling for PMC_SR.MCKRDY. At the moment, for SAMA7G5, the prescaler
will be removed from Linux clock tree as all the frequencies for CPU could
be obtained from PLL and also there will be less overhead when changing
frequency via DVFS.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-14-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAMA7G5 supports DVFS by changing cpuck. On SAMA7G5 mck0 shares the same
parent with cpuck as seen in the following clock tree:
+----------> cpuck
|
FRAC PLL ---> DIV PLL -+-> DIV ---> mck0
mck0 could go b/w 32KHz and 200MHz on SAMA7G5. To avoid mck0 overclocking
while changing FRAC PLL or DIV PLL the commit implements a notifier for
mck0 which applies a safe divider to register (maximum value of the divider
which is 5) on PRE_RATE_CHANGE events (such that changes on PLL to not
overclock mck0) and sets the maximum allowed rate on POST_RATE_CHANGE
events.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-13-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAM9X60's PLL which is also part of SAMA7G5 is composed of 2 parts:
one fractional part and one divider. On SAMA7G5 the CPU PLL could be
changed at run-time to implement DVFS. The hardware clock tree on
SAMA7G5 for CPU PLL is as follows:
+---- div1 ----------------> cpuck
|
FRAC PLL ---> DIV PLL -+-> prescaler ---> div0 ---> mck0
The div1 block is not implemented in Linux; on prescaler block it has
been discovered a bug on some scenarios and will be removed from Linux
in next commits. Thus, the final clock tree that will be used in Linux
will be as follows:
+-----------> cpuck
|
FRAC PLL ---> DIV PLL -+-> div0 ---> mck0
It has been proposed in [1] to not introduce a new CPUFreq driver but
to overload the proper clock drivers with proper operation such that
cpufreq-dt to be used. To accomplish this DIV PLL and div0 implement
clock notifiers which applies safe dividers before FRAC PLL is changed.
The current commit treats only the DIV PLL by adding a notifier that
sets a safe divider on PRE_RATE_CHANGE events. The safe divider is
provided by initialization clock code (sama7g5.c). The div0 is treated
in next commits (to keep the changes as clean as possible).
[1] https://lore.kernel.org/lkml/20210105104426.4tmgc2l3vyicwedd@vireshk-i7/
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-12-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When prescaler value read from register is MASTER_PRES_MAX it means
that the input clock will be divided by 3. Fix the code to reflect
this.
Fixes: 7a110b9107 ("clk: at91: clk-master: re-factor master clock")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-11-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Mask values read/written from/to MCKR against layout->mask as this
mask may be different b/w PMC versions.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-10-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Check if div or pres is zero before using it as argument for ffs().
In case div is zero ffs() will return 0 and thus substracting from
zero will lead to invalid values to be setup in registers.
Fixes: 7a110b9107 ("clk: at91: clk-master: re-factor master clock")
Fixes: 75c88143f3 ("clk: at91: clk-master: add master clock support for SAMA7G5")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-9-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use DIV_ROUND_CLOSEST_ULL() to avoid any inconsistency b/w the rate
computed in sam9x60_frac_pll_recalc_rate() and the one computed in
sam9x60_frac_pll_compute_mul_frac().
Fixes: 43b1bb4a9b ("clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-8-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SAMA7G5 to the list of available PMCs such that the suspend/resume
code for clocks to be used on backup mode.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-7-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Improve readability in clk_sama7g5_master_set() by using local
variables.
Suggested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-6-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAMA7G5 has 4 master clocks (MCK1..4) which are controlled though the
register at offset 0x30 (relative to PMC). In the last/first phase of
suspend/resume procedure (which is architecture specific) the parent
of master clocks are changed (via assembly code) for more power saving
(see file arch/arm/mach-at91/pm_suspend.S, macros at91_mckx_ps_enable
and at91_mckx_ps_restore). Thus the macros corresponding to register
at offset 0x30 need to be shared b/w clk-master.c and pm_suspend.S.
commit ec03f18cc2 ("clk: at91: add register definition for sama7g5's
master clock") introduced the proper macros but didn't adapted the
clk-master.c as well. Thus, this commit adapt the clk-master.c to use
the macros introduced in commit ec03f18cc2 ("clk: at91: add register
definition for sama7g5's master clock").
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-5-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Before going to backup mode architecture specific PM code sets the first
word in securam (file arch/arm/mach-at91/pm.c, function at91_pm_begin()).
Thus take this into account when suspending/resuming clocks. This will
avoid executing unnecessary instructions when suspending to non backup
modes.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-3-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAMA5D2 and SAMA7G5 have a special power saving mode (backup mode) where
most of the SoC's components are powered off (including PMC). Resuming
from this mode is done with the help of bootloader. Peripherals are not
aware of the power saving mode thus most of them are disabling clocks in
proper suspend API and re-enable them in resume API without taking into
account the previously setup rate. Moreover some of the peripherals are
acting as wakeup sources and are not disabling the clocks in this
scenario, when suspending. Since backup mode cuts the power for
peripherals, in resume part these clocks needs to be re-configured.
The initial PMC suspend/resume code was designed only for SAMA5D2's PMC
(as it was the only one supporting backup mode). SAMA7G supports also
backup mode and its PMC is different (few new functionalities, different
registers offsets, different offsets in registers for each
functionalities). To address both SAMA5D2 and SAMA7G5 PMC add
.save_context()/.resume_context() support to each clocks driver and call
this from PMC driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-2-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Ux500 PRCC (peripheral reset and clock controller) can also
control reset of the IP blocks, not just clocks. As the PRCC is probed
as a clock controller and we have other platforms implementing combined
clock and reset controllers, follow this pattern and implement the PRCC
rest controller as part of the clock driver.
The reset controller needs to be selected from the machine as Ux500 has
traditionally selected its mandatory subsystem prerequisites from there.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210921184803.1757916-2-linus.walleij@linaro.org
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
[sboyd@kernel.org: Dropped allocation error message]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The driver, once it found a divider, tries to round it up by increasing
the least significant bit of the fractional part by one when the
round_up argument is set and there's a remainder.
However, since it increases the divider it will actually reduce the
clock rate below what we were asking for, leading to issues with
clk_set_min_rate() that will complain that our rounded clock rate is
below the minimum of the rate.
Since the dividers are fairly precise already, let's remove that part so
that we can have clk_set_min_rate() working.
This is effectively a revert of 9c95b32ca0 ("clk: bcm2835: add a round
up ability to the clock divisor").
Fixes: 9c95b32ca0 ("clk: bcm2835: add a round up ability to the clock divisor")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-3-maxime@cerno.tech
The driver currently tries to pick the closest rate that is lower than
the rate being requested.
This causes an issue with clk_set_min_rate() since it actively checks
for the rounded rate to be above the minimum that was just set.
Let's change the logic a bit to pick the closest rate to the requested
rate, no matter if it's actually higher or lower.
Fixes: 6d18b8adbe ("clk: bcm2835: Support for clock parent selection")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-2-maxime@cerno.tech
Declare ADC1 clkctrl which feeds the magnetic-reader/ADC1 hardware
module.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-2-miquel.raynal@bootlin.com
Update clk_composite_determine_rate() to use rate_ops.determine_rate
when available in combination with a mux. So far clk_divider_ops provide
both, .round_rate and .determine_rate. Removing the former would make
clk-composite fail silently for example on Rockchip platforms (which
heavily use composite clocks).
Add support for using rate_ops.determine_rate when either
rate_ops.round_rate is not available or both (.round_rate and
.determine_rate) are provided.
Suggested-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211016105022.303413-3-martin.blumenstingl@googlemail.com
Tested-by: Alex Bee <knaerzche@gmail.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit 69a00fb3d6 ("clk: divider: Implement and wire up
.determine_rate by default") switches clk_divider_ops to implement
.determine_rate by default. This breaks composite clocks with multiple
parents because clk-composite.c does not use the special handling for
mux + divider combinations anymore (that was restricted to rate clocks
which only implement .round_rate, but not .determine_rate).
Alex reports:
This breaks lot of clocks for Rockchip which intensively uses
composites, i.e. those clocks will always stay at the initial parent,
which in some cases is the XTAL clock and I strongly guess it is the
same for other platforms, which use composite clocks having more than
one parent (e.g. mediatek, ti ...)
Example (RK3399)
clk_sdio is set (initialized) with XTAL (24 MHz) as parent in u-boot.
It will always stay at this parent, even if the mmc driver sets a rate
of 200 MHz (fails, as the nature of things), which should switch it
to any of its possible parent PLLs defined in
mux_pll_src_cpll_gpll_npll_ppll_upll_24m_p (see clk-rk3399.c) - which
never happens.
Restore the original behavior by changing the priority of the conditions
inside clk-composite.c. Now the special rate + mux case (with rate_ops
having a .round_rate - which is still the case for the default
clk_divider_ops) is preferred over rate_ops which have .determine_rate
defined (and not further considering the mux).
Fixes: 69a00fb3d6 ("clk: divider: Implement and wire up .determine_rate by default")
Reported-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211016105022.303413-2-martin.blumenstingl@googlemail.com
Tested-by: Alex Bee <knaerzche@gmail.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20210924133624.112593-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Use the samsung common clk driver to initialize the apollo and atlas
clocks. This removes their custom init functions and uses the
samsung_cmu_register_one() instead.
Signed-off-by: Will McVicker <willmcvicker@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211014195347.3635601-3-willmcvicker@google.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Adds 'struct samsung_cpu_clock' and corresponding CPU clock registration
function to the samsung common clk driver. This allows samsung clock
drivers to register their CPU clocks with the samsung_cmu_register_one()
API.
Currently the exynos5433 apollo and atlas clks have their own custom
init functions to handle registering their CPU clocks. With this patch
we can drop their custom CLK_OF_DECLARE functions and directly call
samsung_cmu_register_one().
Signed-off-by: Will McVicker <willmcvicker@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211014195347.3635601-2-willmcvicker@google.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This is the initial implementation adding only basic clocks like UART,
MMC, I2C and corresponding parent clocks. Design is influenced by
Exynos5433 clock driver.
Bus clock is enabled by default (in probe function) for all CMUs except
CMU_TOP, the reasoning is as follows. By default if bus clock has no
users its "enable count" value is 0. It might be actually running if
it's already enabled in bootloader, but then in some cases it can be
disabled by mistake. For example, such case was observed when
dw_mci_probe() enabled the bus clock, then failed to do something and
disabled that bus clock on error path. After that, even the attempt to
read the 'clk_summary' file in DebugFS freezed forever, as CMU bus clock
ended up being disabled and it wasn't possible to access CMU registers
anymore.
To avoid such cases, CMU driver must increment the ref count for that
bus clock by running clk_prepare_enable(). There is already existing
'.clk_name' field in struct samsung_cmu_info, exactly for that reason.
It was added in commit 523d3de41f ("clk: samsung: exynos5433: Add
support for runtime PM"), with next mentioning in commit message:
> Also for each CMU there is one special parent clock, which has to be
> enabled all the time when any access to CMU registers is being done.
But that clock is actually only enabled in Exynos5433 clock driver right
now. So the same code is added to exynos850_cmu_probe() function,
As was described above, it might be helpful not only for PM reasons, but
also to prevent possible erroneous clock gating on error paths.
Another way to workaround that issue would be to use CLOCK_IS_CRITICAL
flag for corresponding gate clocks. But that might be not very good
design decision, as we might still want to disable that bus clock, e.g.
on PM suspend.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211008154352.19519-6-semen.protsenko@linaro.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Commit 419b3ab698 ("clk: versatile: remove dependency on ARCH_*")
made the whole menu of ARM reference clock drivers visible on all
architectures. I can't see how this is an improvement for non-ARM
users. Unless build-testing, there is no point on presenting
ARM-only clock drivers on other architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20210901180953.5bd2a994@endymion
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For consistency, prefix the ICST config option with CLK as all other
clock source drivers have.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210901180833.4558932d@endymion
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On sm8250 dispcc and videocc registers are powered up by the MMCX power
domain. Currently we use a regulator to enable this domain on demand,
however this has some consequences, as genpd code is not reentrant.
Make gdsc code also use pm_runtime calls to ensure that registers are
accessible during the gdsc_enable/gdsc_disable operations.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829154757.784699-6-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On sm8250 dispcc and videocc registers are powered up by the MMCX power
domain. Use runtime PM calls to make sure that required power domain is
powered on while we access clock controller's registers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829154757.784699-5-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On sm8250 dispcc and videocc registers are powered up by the MMCX power
domain. Use runtime PM calls to make sure that required power domain is
powered on while we access clock controller's registers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210829154757.784699-4-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
After commit 3165d1e3c7 ("clk: qcom: gcc: Remove CPUSS clocks control
for SC7280") this array is unused. Remove it.
Reported-by: kernel test robot <lkp@intel.com>
Cc: Taniya Das <tdas@codeaurora.org>
Fixes: 3165d1e3c7 ("clk: qcom: gcc: Remove CPUSS clocks control for SC7280")
Link: https://lore.kernel.org/r/20211014191259.1689641-1-sboyd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the camera clock controller found on SC7280 based
devices.
This would allow camera drivers to probe and control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1633567425-11953-2-git-send-email-tdas@codeaurora.org
[sboyd@kernel.org: Make some VCOs unsigned long]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the lpass clock controller found on SC7280 based devices.
This would allow lpass peripheral loader drivers to control the clocks to
bring the subsystem out of reset.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1633484416-27852-3-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Don't rely on the programmer to enter the name of array elements, since the
computer can compute it with much less chance of making a mistake.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210923162645.23257-9-konrad.dybcio@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This should be the last "add missing clocks" commit, as to
my knowledge there are no more clocks registered within gcc.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210923162645.23257-5-konrad.dybcio@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for RPM-managed clocks on the QCM2290 platform.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210917030434.19859-4-shawn.guo@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As there is a `rate` field in clk_smd_rpm, clk_smd_rpm_recalc_rate() can
be used by branch clocks to report rate as well, rather than assuming
the rate is always same as parent clock. This assumption doesn't hold
on platforms like QCM2290, where xo_board is 38.4MHz while bi_tcxo is
19.2MHz.
To get this work, XO buffered clocks need the following updates.
- Assign a correct rate rather than the fake one which is being used to
generate binary value for clk_smd_rpm_req interface.
- Explicitly handle the clk_smd_rpm_req interface value for XO buffered
clocks (.rpm_res_type being QCOM_SMD_RPM_CLK_BUF_A).
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210917030434.19859-2-shawn.guo@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sboyd@kernel.org: Do cpu_to_le32() again to keep sparse happy]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add Global Clock Controller (GCC) driver for QCM2290. This is a porting
of gcc-scuba driver from CAF msm-4.19, with GDSC support added on top.
Because the alpha_pll on the platform has a different register
layout (offsets), its own clk_alpha_pll_regs_offset[] is used in the
driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210919023308.24498-3-shawn.guo@linaro.org
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@kernel.org: Drop duplicate includes, clk.h include, module alias]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It looks that the offset 0x7d060 is a copy & paste from above
hlos1_vote_turing_mmu_tbu1_gdsc. Correct it to 0x7d07c as per
downstream kernel.
Fixes: cbe63bfdc5 ("clk: qcom: Add Global Clock controller (GCC) driver for SM6115")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210919022308.24046-1-shawn.guo@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pll0831x PLL is used in Exynos850 SoC for top-level fractional PLLs. The
code was derived from very similar pll36xx type, with next differences:
1. Lock time for pll0831x is 500*P_DIV, when for pll36xx it's 3000*P_DIV
2. It's not suggested in Exynos850 TRM that S_DIV change doesn't require
performing PLL lock procedure (which is done in pll36xx
implementation)
3. The offset from PMS-values register to K-value register is 0x8 for
pll0831x, when for pll36xx it's 0x4
When defining pll0831x type, CON3 register offset should be provided as
a "con" parameter of PLL() macro, like this:
PLL(pll_0831x, 0, "fout_mmc_pll", "oscclk",
PLL_LOCKTIME_PLL_MMC, PLL_CON3_PLL_MMC, pll0831x_26mhz_tbl),
To define PLL rates table, one can use PLL_36XX_RATE() macro, e.g.:
PLL_36XX_RATE(26 * MHZ, 799999877, 31, 1, 0, -15124)
as it's completely appropriate for pl0831x type and there is no sense in
duplicating that.
If bit #1 (MANUAL_PLL_CTRL) is not set in CON1 register, it won't be
possible to set new rate, with next error showing in kernel log:
Could not lock PLL fout_mmc_pll
That can happen for example if bootloader clears that bit beforehand.
PLL driver doesn't account for that, so if MANUAL_PLL_CTRL bit was
cleared, it's assumed it was done for a reason and it shouldn't be
possible to change that PLL's rate at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211008154352.19519-3-semen.protsenko@linaro.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
pll0822x PLL is used in Exynos850 SoC for top-level integer PLLs. The
code was derived from very similar pll35xx type, with next differences:
1. Lock time for pll0822x is 150*P_DIV, when for pll35xx it's 270*P_DIV
2. It's not suggested in Exynos850 TRM that S_DIV change doesn't require
performing PLL lock procedure (which is done in pll35xx
implementation)
When defining pll0822x type, CON3 register offset should be provided as
a "con" parameter of PLL() macro, like this:
PLL(pll_0822x, 0, "fout_shared0_pll", "oscclk",
PLL_LOCKTIME_PLL_SHARED0, PLL_CON3_PLL_SHARED0,
exynos850_shared0_pll_rates),
To define PLL rates table, one can use PLL_35XX_RATE() macro, e.g.:
PLL_35XX_RATE(26 * MHZ, 1600 * MHZ, 800, 13, 0)
as it's completely appropriate for pl0822x type and there is no sense in
duplicating that.
If bit #1 (MANUAL_PLL_CTRL) is not set in CON1 register, it won't be
possible to set new rate, with next error showing in kernel log:
Could not lock PLL fout_shared1_pll
That can happen for example if bootloader clears that bit beforehand.
PLL driver doesn't account for that, so if MANUAL_PLL_CTRL bit was
cleared, it's assumed it was done for a reason and it shouldn't be
possible to change that PLL's rate at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211008154352.19519-2-semen.protsenko@linaro.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add SDHI clk mux support to select SDHI clock from different clock
sources.
As per HW manual, direct clock switching from 533MHz to 400MHz and
vice versa is not recommended. So added support for handling this
in mux.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211007111434.8665-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We want to reuse this code for V3U soon. Because its RPCCKCR register is
at a different offset, the moved functions do not use the base register
as an argument anymore but the RPCCKCR register itself. Verified that an
Eagle board with R-Car V3M still works.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211006085836.42155-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Currently, at91 pmc driver always register the syscore_ops whatever
the status of the pmc node that has been found. When set as secure
and disabled, the pmc should not be accessed or this will generate
abort exceptions.
To avoid this, add a check on node availability before registering
the syscore operations.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20210913082633.110168-1-clement.leger@bootlin.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: b3b02eac33 ("clk: at91: Add sama5d2 suspend/resume")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CPUSS clocks are kept always ON and at a fixed frequency of 100MHZ
from the bootloader and no longer required to be controlled from HLOS.
Fixes: a3cc092196 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7280")
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1633579571-25475-1-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Kai Song <songkai01@inspur.com>
Link: https://lore.kernel.org/r/20211006043627.5125-1-songkai01@inspur.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Building CLK_IMX8ULP without selecting MXC_CLK causes the following
build errors:
ld: drivers/clk/imx/clk-imx8ulp.o: in function `imx8ulp_clk_cgc2_init':
clk-imx8ulp.c:(.text+0xd0): undefined reference to `imx_ccm_lock'
ld: clk-imx8ulp.c:(.text+0x14f): undefined reference to `imx_clk_hw_pllv4'
ld: clk-imx8ulp.c:(.text+0x15a): undefined reference to `imx_ccm_lock'
Avoid this problem by making CLK_IMX8ULP select MXC_CLK.
Fixes: c43a801a57 ("clk: imx: Add clock driver for imx8ulp")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20211006190008.1935051-1-festevam@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
According to the imx6ul Reference Manual the csi clk gate register is
CCM_CCGR3 (offset 0x74) bit 0/1. For the imx6ull on the other hand the
Reference Manual lists register CCM_CCGR2 (offset 0x70) bit 2/3 as the
csi clk gate which is the current setting.
Tests have shown though that the correct csi clk gate register for the
imx6ull is actually CCM_CCGR3 bit 0/1 as well. Thus set the correct
register for both platforms.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210927072857.3940880-2-s.riedmueller@phytec.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
The csi_sel mux register is located in the CCM register base and not the
CCM_ANALOG register base. So move it to the correct position in code.
Otherwise changing the parent of the csi clock can lead to a complete
system failure due to the CCM_ANALOG_PLL_SYS_TOG register being falsely
modified.
Also remove the SET_RATE_PARENT flag since one possible supply for the
csi_sel mux is the system PLL which we don't want to modify.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210927072857.3940880-1-s.riedmueller@phytec.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Export the necessary symbols to fix the build break when clk-imx8ulp
build as module
Fixes: c43a801a57 ("clk: imx: Add clock driver for imx8ulp")
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210917061629.3798360-1-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
On i.MX8ULP, for some of the PCCs, it has a peripheral SW RST bit
resides in the same registers as the clock controller. So add this
SW RST controller support alongs with the pcc clock initialization.
the reset and clock shared the same register, to avoid accessing
the same register by reset control and clock control concurrently,
locking is necessary, so reuse the imx_ccm_lock spinlock to simplify
the code.
Suggested-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-10-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Add clock driver for i.MX8ULP.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-9-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
On i.MX8ULP, the 'CLK_SET_RATE_PARENT' flag should NOT be
set and according to the laest RM, the PFD divider value range
seems will be changed in the future, so update the pfdv2 to
include the specific support for i.MX8ULP.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-8-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
It is possible that a PFD is enabled in HW but not in SW. That
means the enable count & prepare count of the PFD clock is '0',
so the 'CLK_SET_RATE' flag can do nothing when the rate is changed
while the PFD is hw enabled. In order to safely change the pfd
rate, we can disable the PFD directly if it is hw enabled but not
used by SW end user.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-7-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
For the imx_composite-7ulp clock type, The clock parent should
be changed explicitly by end user of this clock, if the the
'CLK_SET_RATE_NO_REPARENT' flag is not set, when user want to
set a clock frequency that can NOT get from HW accurately, then
the clock's parent will be switch to another clock parent sometimes.
This is NOT what we expected and introduced some additional debug
effort, so add the 'CLK_SET_RATE_NO_REPARENT' to avoid such unexpected
result.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-6-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
i.MX7ULP peripheral clock ONLY allow parent/rate to be changed
with clock gated, however, during clock tree initialization, the
peripheral clock could be enabled by bootloader, but the prepare
count in clock tree is still zero, so clock core driver will allow
parent/rate changed even with CLK_SET_RATE_GATE/CLK_SET_PARENT_GATE
set, but the change will fail due to HW NOT allow parent/rate change
with clock enabled. It will cause clock HW status mismatch with
clock tree info and lead to function issue. Below is an example:
usdhc0's pcc clock value is 0xC5000000 during kernel boot up, it
means usdhc0 clock is enabled, its parent is APLL_PFD1. In DT file,
the usdhc0 clock settings are as below:
assigned-clocks = <&pcc2 IMX7ULP_CLK_USDHC0>;
assigned-clock-parents = <&scg1 IMX7ULP_CLK_NIC1_DIV>;
when kernel boot up, the clock tree info is as below, but the usdhc0
PCC register is still 0xC5000000, which means its parent is still
from APLL_PFD1, which is incorrect and cause usdhc0 NOT work.
nic1_clk 2 2 0 176000000 0 0 50000
usdhc0 0 0 0 176000000 0 0 50000
After making sure the peripheral clock is disabled during clock tree
initialization, the usdhc0 is working, and this change is necessary
for all i.MX7ULP peripheral clocks.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-5-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
On i.MX8ULP, some peripherals have a sw_rst control resides
in the per device PCC clock control register, all others are
same as i.MX7ULP, so update the 7ulp clock composite driver to
support i.MX8ULP to maxmimize the code reuse.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-4-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
The PLLs used on i.MX8ULP is mostly the same as on i.MX7ULP,
except the PLL register offset is changed. Change the PLLv4
driver for code reuse on i.MX7ULP and i.MX8ULP.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210914065208.3582128-3-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
It looks much cleaner to just have a macro compared to having
a function that passes NULL as dev to the lower-level
imx_dev_clk_hw_pll14xx.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/1631521490-17171-9-git-send-email-abel.vesa@nxp.com
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Rather than having multiple different macros for each different type
of imx8m_clk_hw_composite, implement them in such a way so we can
take advantage the most of the already defined simpler types. Basically,
we end up having one low-level __imx8m_clk_hw_composite function, a
wrapper to simplify the parents related arguments called
_imx8m_clk_hw_composite and then all the types can use those for each
specific case.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/1631521490-17171-8-git-send-email-abel.vesa@nxp.com
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Instead of having multiple inline functions that were calling
clk_hw_register_divider, implement a generic low-level
__imx_clk_hw_divider and implement the rest as macros that
pass on as arguments whatever is needed in each case.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/1631521490-17171-7-git-send-email-abel.vesa@nxp.com
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Instead of having multiple inline functions that were calling
clk_hw_register_mux, implement a generic low-level __imx_clk_hw_mux
and implement the rest as macros that pass on as arguments whatever
is needed in each case.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/1631521490-17171-6-git-send-email-abel.vesa@nxp.com
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Instead of having multiple inline functions that were calling
clk_hw_register_gate2, implement a generic low-level __imx_clk_hw_gate2
and implement the rest as macros that pass on as arguments whatever
is needed in each case.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/1631521490-17171-5-git-send-email-abel.vesa@nxp.com
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
- Fix inverted logic in RZ/G2L .is_enabled() function.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYVMdswAKCRCKwlD9ZEnx
cOA0AP9wSDo+INCJKIHDqjqB8cuFnnlAp+FwDL+eRCZz1REEjAEAyedXjtgkkVuR
jbtxoWc7CLehZn4sDwaWSydmMOn9uwU=
=czuu
-----END PGP SIGNATURE-----
Merge tag 'renesas-clk-for-v5.15-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-fixes
Pull Renesas clk driver fixes from Geert Uytterhoeven:
- Fix inverted logic in RZ/G2L .is_enabled() function
* tag 'renesas-clk-for-v5.15-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: rzg2l: Fix clk status function
clk: renesas: r9a07g044: Mark IA55_CLK and DMAC_ACLK critical
Add support for the Z0 and Z1 (Cortex-A76 Sub-system 0 and 1) clocks,
based on the existing support for Z clocks on R-Car Gen3.
As the offsets of the CPG_FRQCRB and CPG_FRQCRC registers on R-Car V3U
differ from the offsets on other R-Car Gen3 SoCs, we cannot use the
existing R-Car Gen3 support as-is. For now, just make a copy, and
change the register offsets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/2112e3bc870580c623bdecfeff8c74739699c610.1625219713.git.geert+renesas@glider.be
As per RZ/G2L HW(Rev.0.50) manual, clock monitor register value
0 means clock is not supplied and 1 means clock is supplied.
This patch fixes the issue by removing the inverted logic.
Fixing the above, triggered following 2 issues
1) GIC interrupts don't work if we disable IA55_CLK and DMAC_ACLK.
Fixed this issue by adding these clocks as critical clocks.
2) DMA is not working, since the DMA driver is not turning on DMAC_PCLK.
So will provide a fix in the DMA driver to turn on DMA_PCLK.
Fixes: ef3c613ccd ("clk: renesas: Add CPG core wrapper for RZ/G2L SoC")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IA55_CLK and DMAC_ACLK as critical clocks.
Previously it worked ok, because of a bug in clock status function
and the following patch in this series fixes the original bug.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Fixes: eb829e549b ("clk: renesas: r9a07g044: Add DMAC clocks/resets")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The AXI and CHI clocks use the same register bit for controlling clock
output. Add a new clock type for coupled clocks, which sets the
CPG_CLKON_ETH.CLK[01]_ON bit when at least one clock is enabled, and
clears the bit only when both clocks are disabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_FOUT3 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
This patch also renames the PLL5_DIV2 core clock to PLL5_250 to match
with the register description as mentioned in RZ/G2L HW manual (Rev.1.00).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support to handle mux clocks in order to select a clock source
from multiple sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Switch from the "_ro" clock op variants to the mutable ones for all
video clocks. This will allow the VPU driver to change the clocks as
needed for the different video output modes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-6-martin.blumenstingl@googlemail.com
Add the reg_sequence to initialize the HDMI PLL with the settings for
a video mode that doesn't require PLL internal clock doubling. These
settings are taken from the 3.10 vendor kernel's driver for the 2970MHz
PLL setting used for the 1080P video mode. This puts the PLL into a
defined state and the Linux kernel can take over.
While not all bits for this PLL are implemented using these "defaults"
and then applying M, N and FRAC seems to work fine.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-5-martin.blumenstingl@googlemail.com
The 3.10 vendor kernel uses only specific HDMI PLL M/N parameter
combinations. The PLL won't lock for values smaller than 50 if the
internal doubling (which is yet unknown how to use it) is disabled.
However, when this doubling is enabled then the values smaller than 50
will lock just fine. The only restriction for values greater than 50 is
that the resulting frequency must not exceed the 3.0GHz limit.
These values are taken from the endlessm 3.10 kernel which includes
additional M/N combinations for some VESA and 75Hz display modes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-4-martin.blumenstingl@googlemail.com
HHI_VID_DIVIDER_CNTL[11] must be enabled for the video clock tree to
work. This bit is described as "LVDS_CLK_EN". It is not 100% clear where
this bit has to be placed in the hierarchy. But since the "LVDS_OUT" of
the HDMI PLL uses it's own set of registers it's more likely that this
"LVDS_CLK_EN" bit actually enables the input of the "hdmi_pll_lvds_out"
clock to the "vid_pll_in_sel" tree.
Add a gate definition for this bit (which will not be exported) so that
the kernel can manage all required bits to enable and disable the video
clocks.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-3-martin.blumenstingl@googlemail.com
Use CLK_SET_RATE_NO_REPARENT for the vclk{,2}_in_sel clocks. The only
parent which is actually used is vid_pll_final_div. This should be set
using assigned-clock-parents in the .dts rather than removing some
"unwanted" clock parents from the clock driver.
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-2-martin.blumenstingl@googlemail.com
Setting the video clocks requires fine-tuned adjustments of various
video clocks. Export the required ones to allow changing the video clock
for the CVBS and HDMI outputs at runtime.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-7-martin.blumenstingl@googlemail.com
Replace builtin_platform_driver_probe with module_platform_driver_probe
because that rk3399 and rk3568 can be built as kernel modules.
Fixes: 70d839e276 ("clk: rockchip: rk3399: Support module build")
Fixes: cf911d89c4 ("clk: rockchip: add clock controller for rk3568")
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20210904152856.31946-1-miles.chen@mediatek.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We have DT IDs for PCLK_COREDBG_L and PCLK_COREDBG_B, but we don't
actually expose them.
Note that this requires the previous patch (making "armclkl" and
"armclkb" into "critical" clocks) to prevent these clocks from taking
down the CPU.
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210908111337.v2.2.If29cd838efbcee4450a62b8d84a99b23c86e0a3f@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The CPU clocks don't currently have any owner (e.g., cpufreq-dt doesn't
enable() them -- and even if it did, it's not early enough compared to
other consumers -- nor does arch/arm64/kernel/smp.c), and instead are
simply assumed to be "on" all the time.
They are also parents of a few other clocks which haven't been
previously exposed for other devices to consume. If we want to expose
those clocks, then the common clock framework may eventually choose to
disable their parents (including the CPU PLLs) -- which is no fun for
anyone.
Thus, mark the CPU clocks as critical, to prevent them from being
disabled implicitly.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210908111337.v2.1.I006bb36063555079b1a88f01d20e38d7e4705ae0@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Instead of having multiple inline functions that were calling
clk_hw_register_gate, implement a generic low-level __imx_clk_hw_gate
and implement the rest as macros that pass on as arguments whatever
is needed in each case.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/1631521490-17171-4-git-send-email-abel.vesa@nxp.com
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Implement the clk based helpers as macros rather than as inline
functions. Once all the provider drivers have switch to clk_hw,
all the clk based macros will go away.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/1631521490-17171-3-git-send-email-abel.vesa@nxp.com
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Peng Fan