Some Root Ports on Intel Tiger Lake and Alder Lake systems support the RP
Extensions for DPC and the RP PIO Log registers but incorrectly advertise
an RP PIO Log Size of zero. This means the kernel complains that:
DPC: RP PIO log size 0 is invalid
and if DPC is triggered, the DPC driver will not dump the RP PIO Log
registers when it should.
This is caused by a BIOS bug and should be fixed the BIOS for future CPUs.
Add a quirk to set the correct RP PIO Log size for the affected Root Ports.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209943
Link: https://lore.kernel.org/r/20220816102042.69125-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
- Remove pci_get_legacy_ide_irq(); use ATA_PRIMARY_IRQ() and
ATA_SECONDARY_IRQ() instead (Stafford Horne)
- Remove isa_dma_bridge_buggy, except for x86_32, the only place it's used
(Stafford Horne)
- Define ARCH_GENERIC_PCI_MMAP_RESOURCE for csky (Stafford Horne)
- Move common PCI definitions that arches sometimes override to
asm-generic/pci.h (Stafford Horne)
- Include <linux/isa-dma.h> for 'isa_dma_bridge_buggy' when needed
(bisection hole here) (Randy Dunlap)
* pci/header-cleanup-immutable:
PCI: Stub __pci_ioport_map() for arches that don't support it at all
x86/cyrix: include header linux/isa-dma.h
asm-generic: Add new pci.h and use it
csky: PCI: Define ARCH_GENERIC_PCI_MMAP_RESOURCE
PCI: Move isa_dma_bridge_buggy out of asm/dma.h
PCI: Remove pci_get_legacy_ide_irq() and asm-generic/pci.h
- Fix tegra_pcie_config_ep() power management in error path (Miaoqian Lin)
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and Endpoint
mode (Vidya Sagar)
- Disable MSI for Tegra234 Root Ports so they use INTx for all events (PCIe
doesn't allow mixing INTx and MSI/MSI-X) (Vidya Sagar)
- Search for Vendor-Specific RAS-DEC capability instead of hard-coding
offset (Vidya Sagar)
- Fix unintentional APPL_INTR_STATUS_L0 value overwrite in Root Port
interrupt handling (Vidya Sagar)
- Clear Bandwidth Management interrupt status bit to avoid interrupt storm
(Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix offset when clearing bit in Data Link Feature capability (Vidya
Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya Sagar)
* pci/ctrl/tegra194:
PCI: tegra194: Add Tegra234 PCIe support
PCI: tegra194: Extend Endpoint mode support
PCI: tegra194: Fix link up retry sequence
PCI: tegra194: Clean up the exit path for Endpoint mode
PCI: tegra194: Enable support for 256 Byte payload
PCI: tegra194: Clear bandwidth management status
PCI: tegra194: Fix Root Port interrupt handling
PCI: tegra194: Find RAS DES PCIe capability offset
Revert "PCI: tegra194: Rename tegra_pcie_dw to tegra194_pcie"
PCI: Disable MSI for Tegra234 Root Ports
dt-bindings: PCI: tegra234: Add schema for tegra234 Endpoint mode
dt-bindings: PCI: tegra234: Add schema for tegra234 Root Port mode
dt-bindings: PCI: tegra194: Convert to json-schema
PCI: tegra194: Fix PM error handling in tegra_pcie_config_ep()
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
# drivers/pci/controller/dwc/pcie-tegra194.c
The isa_dma_bridge_buggy symbol is only used for x86_32, and only x86_32
platforms or quirks ever set it.
Add a new linux/isa-dma.h header that #defines isa_dma_bridge_buggy to 0
except on x86_32, where we keep it as a variable, and remove all the arch-
specific definitions.
[bhelgaas: commit log]
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Link: https://lore.kernel.org/r/20220722214944.831438-3-shorne@gmail.com
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tegra234 PCIe Root Ports don't generate MSI interrupts for PME and AER
events. Since PCIe spec (r6.0 sec 6.1.4.3) doesn't support using a mix of
INTx and MSI/MSI-X, MSI needs to be disabled to avoid Root Port service
drivers registering their respective ISRs with MSI interrupt and to let
only INTx be used for all events.
Link: https://lore.kernel.org/r/20220721142052.25971-8-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Broadcom BCM5750x NICs may be multi-function devices. They do not
advertise ACS capability. Peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for these devices so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
Link: https://lore.kernel.org/r/1654796507-28610-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel DG2 discrete graphics PCIe endpoints advertise L1 acceptable exit
latency to be < 1us even though they can actually tolerate unlimited exit
latencies just fine. Quirk the L1 acceptable exit latency for these
endpoints to be unlimited so ASPM L1 can be enabled.
[bhelgaas: use FIELD_GET/FIELD_PREP, wordsmith comment & commit log]
Link: https://lore.kernel.org/r/20220405093810.76613-1-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
-----BEGIN PGP SIGNATURE-----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=5Q9H
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Move the VGA arbiter from drivers/gpu to drivers/pci because it's
PCI-specific, not GPU-specific (Bjorn Helgaas)
- Select the default VGA device consistently whether it's enumerated
before or after VGA arbiter init, which fixes arches that enumerate
PCI devices late (Huacai Chen)
Resource management:
- Support BAR sizes up to 8TB (Dongdong Liu)
PCIe native device hotplug:
- Fix "Command Completed" tracking to avoid spurious timouts when
powering off empty slots (Liguang Zhang)
- Quirk Qualcomm devices that don't implement Command Completed
correctly, again to avoid spurious timeouts (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Add Intel 3rd Gen Intel Xeon Scalable Processors to whitelist
(Michael J. Ruhl)
APM X-Gene PCIe controller driver:
- Revert generic DT parsing changes that broke some machines in the
field (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Allow controller probe to succeed even when no devices currently
present to allow hot-add later (Fabio Estevam)
- Enable power management on i.MX6QP (Richard Zhu)
- Assert CLKREQ# on i.MX8MM so enumeration doesn't hang when no
device is connected (Richard Zhu)
Marvell Aardvark PCIe controller driver:
- Fix MSI and MSI-X support (Marek Behún, Pali Rohár)
- Add support for ERR and PME interrupts (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Add DT binding and support for "num-lanes" (Pali Rohár)
- Add support for INTx interrupts (Pali Rohár)
Microsoft Hyper-V host bridge driver:
- Avoid unnecessary hypercalls when unmasking IRQs on ARM64 (Boqun
Feng)
Qualcomm PCIe controller driver:
- Add SM8450 DT binding and driver support (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Help the controller get to the L1 state since the hardware can't do
it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE (~0) for reads that fail on PCIe (Marek
Vasut)
SiFive FU740 PCIe controller driver:
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe (Ben Dooks)
Socionext UniPhier Pro5 controller driver:
- Add NX1 DT binding and driver support (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Restore MSI configuration so MSI works after resume (Jisheng
Zhang)"
* tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
x86/PCI: Add #includes to asm/pci_x86.h
PCI: ibmphp: Remove unused assignments
PCI: cpqphp: Remove unused assignments
PCI: fu740: Remove unused assignments
PCI: kirin: Remove unused assignments
PCI: Remove unused assignments
PCI: Declare pci_filp_private only when HAVE_PCI_MMAP
PCI: Avoid broken MSI on SB600 USB devices
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
PCI: dwc: Restore MSI Receiver mask during resume
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
PCI/VGA: Replace full MIT license text with SPDX identifier
PCI/VGA: Use unsigned format string to print lock counts
PCI/VGA: Log bridge control messages when adding devices
...
There are enough VBIOS escapes without the proper workaround that some
users still hit this. Microsoft never productized ATS on Windows so OEM
platforms that were Windows-only didn't always validate ATS.
The advantages of ATS are not worth it compared to the potential
instabilities on harvested boards. Disable ATS on all Navi10 and Navi14
boards.
Symptoms include:
amdgpu 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0007 address=0xffffc02000 flags=0x0000]
AMD-Vi: Event logged [IO_PAGE_FAULT device=07:00.0 domain=0x0007 address=0xffffc02000 flags=0x0000]
[drm:amdgpu_job_timedout [amdgpu]] *ERROR* ring sdma0 timeout, signaled seq=6047, emitted seq=6049
amdgpu 0000:07:00.0: amdgpu: GPU reset begin!
amdgpu 0000:07:00.0: amdgpu: GPU reset succeeded, trying to resume
amdgpu 0000:07:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring sdma0 test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block <sdma_v4_0> failed -110
amdgpu 0000:07:00.0: amdgpu: GPU reset(1) failed
Related commits:
e8946a53e2 ("PCI: Mark AMD Navi14 GPU ATS as broken")
a2da5d8cc0 ("PCI: Mark AMD Raven iGPU ATS as broken in some platforms")
45beb31d3a ("PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken")
5e89cd303e ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")
d28ca864c4 ("PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken")
9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
[bhelgaas: add symptoms and related commits]
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1760
Link: https://lore.kernel.org/r/20220222160801.841643-1-alexander.deucher@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Guchun Chen <guchun.chen@amd.com>
-----BEGIN PGP SIGNATURE-----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=Vgg4
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups
(Greg Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum
(Rajat Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
Resource management:
- Always write Intel I210 ROM BAR on update to work around device
defect (Bjorn Helgaas)
PCIe native device hotplug:
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas
Wunner)
Power management:
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power
management to generic power management (Vaibhav Gupta)
IOMMU:
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
so it can work with an IOMMU (Yifeng Li)
Error handling:
- Add PCI_ERROR_RESPONSE and related definitions for signaling and
checking for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers,
instead of in host controller drivers, when transactions fail on
PCI (Naveen Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config
reads (Naveen Naidu)
Peer-to-peer DMA:
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
ASPM:
- Calculate link L0s and L1 exit latencies when needed instead of
caching them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed
instead of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
APM X-Gene PCIe controller driver:
- Fix IB window setup, which was broken by the fact that IB resources
are now sorted in address order instead of DT dma-ranges order (Rob
Herring)
Apple PCIe controller driver:
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
Broadcom STB PCIe controller driver:
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors
and not fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding
(Jim Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected
devices (Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is
added or removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup
devices (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Use DWC common ops instead of layerscape-specific link-up functions
(Hou Zhiqiang)
Intel VMD host bridge driver:
- Honor platform ACPI _OSC feature negotiation for Root Ports below
VMD (Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
- Reset everything below VMD before enumerating to work around
failure to enumerate NVMe devices when guest OS reboots (Nirmal
Patel)
Bridge emulation (used by Marvell Aardvark and MVEBU):
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali
Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they
must have at least a PCIe Capability (Pali Rohár)
Marvell Aardvark PCIe controller driver:
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2,
DEVSTA2, LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali
Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
registers (Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali
Rohár)
- Mask all interrupts when unbinding host controller driver (Pali
Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali
Rohár)
- Disable common PHY when unbinding host controller driver (Pali
Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the ARM
implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali
Rohár)
- Disable Root Port windows when base/limit set to invalid values
(Pali Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect
the actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root
Ports (Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports
(Pali Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on
Armada XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module
(Pali Rohár)
- Add support for compiling as a module (Pali Rohár)
MediaTek PCIe controller driver:
- Assert PERST# for 100ms to allow power and clock to stabilize
(qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to
respond to the request causes failure to exit L1 PM Substate
(Jianjun Wang)
MediaTek MT7621 PCIe controller driver:
- Declare mt7621_pci_ops static (Sergio Paracuellos)
- Give pcibios_root_bridge_prepare() access to host bridge windows
(Sergio Paracuellos)
- Move MIPS I/O coherency unit setup from driver to
pcibios_root_bridge_prepare() (Sergio Paracuellos)
- Add missing MODULE_LICENSE() (Sergio Paracuellos)
- Allow COMPILE_TEST for all arches (Sergio Paracuellos)
Microsoft Hyper-V host bridge driver:
- Add hv-internal interfaces to encapsulate arch IRQ dependencies
(Sunil Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
Qualcomm PCIe controller driver:
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16()
(Manivannan Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
Renesas R-Car PCIe controller driver:
- Fix aarch32 abort handler so it doesn't check the wrong bus clock
before accessing the host controller (Marek Vasut)
TI Keystone PCIe controller driver:
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode
DT properties (Kishon Vijay Abraham I)
MicroSemi Switchtec management driver:
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and
initialized for every call (Kelvin Cao)
Host controller driver cleanups:
- Use of_device_get_match_data(), not of_match_device(), when we only
need the device data in altera, artpec6, cadence, designware-plat,
dra7xx, keystone, kirin (Fan Fei)
- Drop pointless of_device_get_match_data() cast in j721e (Bjorn
Helgaas)
- Drop redundant struct device * from j721e since struct cdns_pcie
already has one (Bjorn Helgaas)
- Rename driver structs to *_pcie in intel-gw, iproc, ls-gen4,
mediatek-gen3, microchip, mt7621, rcar-gen2, tegra194, uniphier,
xgene, xilinx, xilinx-cpm for consistency across drivers (Fan Fei)
- Fix invalid address space conversions in hisi, spear13xx (Bjorn
Helgaas)
Miscellaneous:
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming
Wang)"
* tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (151 commits)
PCI: mt7621: Allow COMPILE_TEST for all arches
PCI: mt7621: Add missing MODULE_LICENSE()
PCI: mt7621: Move MIPS setup to pcibios_root_bridge_prepare()
PCI: Let pcibios_root_bridge_prepare() access bridge->windows
PCI: mt7621: Declare mt7621_pci_ops static
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
misc: pci_endpoint_test: Terminate statement with semicolon
...
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming Wang)
* pci/misc:
misc: pci_endpoint_test: Terminate statement with semicolon
PCI: Correct misspelled words
PCI: Change capability register offsets to hex
PCI: Sort Intel Device IDs by value
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller so it
can work with an IOMMU (Yifeng Li)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and initialized for
every call (Kelvin Cao)
* pci/switchtec:
PCI/switchtec: Declare local state_names[] as static
PCI/switchtec: Add Gen4 automotive device IDs
Per PCIe r5, sec 7.5.1.2.4, a device must not claim accesses to its
Expansion ROM unless both the Memory Space Enable and the Expansion ROM
Enable bit are set. But apparently some Intel I210 NICs don't work
correctly if the ROM BAR overlaps another BAR, even if the Expansion ROM is
disabled.
Michael reported that on a Kontron SMARC-sAL28 ARM64 system with U-Boot
v2021.01-rc3, the ROM BAR overlaps BAR 3, and networking doesn't work at
all:
BAR 0: 0x40000000 (32-bit, non-prefetchable) [size=1M]
BAR 3: 0x40200000 (32-bit, non-prefetchable) [size=16K]
ROM: 0x40200000 (disabled) [size=1M]
NETDEV WATCHDOG: enP2p1s0 (igb): transmit queue 0 timed out
Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT)
igb 0002:01:00.0 enP2p1s0: Reset adapter
Previously, pci_std_update_resource() wrote the assigned ROM address to the
BAR only when the ROM was enabled. This meant that the I210 ROM BAR could
be left with an address assigned by firmware, which might overlap with
other BARs.
Quirk these I210 devices so pci_std_update_resource() always writes the
assigned address to the ROM BAR, whether or not the ROM is enabled.
Link: https://lore.kernel.org/r/20211223163754.GA1267351@bhelgaas
Link: https://lore.kernel.org/r/20201230185317.30915-1-michael@walle.cc
Link: https://bugzilla.kernel.org/show_bug.cgi?id=211105
Reported-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix a number of misspelled words, and while at it, correct two phrases used
to indicate a status of an operation where words used have been cleverly
truncated and thus always trigger a spellchecking error while performing a
static code analysis over the PCI tree.
[bhelgaas: reverse sense of quirk ternary]
Link: https://lore.kernel.org/r/20220107225942.121484-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU. Add it to the list of devices that need the
quirk.
Without this patch, device initialization fails with DMA errors:
ata8: softreset failed (1st FIS failed)
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
After applying the patch, the controller can be successfully initialized:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
ata8.00: ATAPI: PIONEER BD-RW BDR-207M, 1.21, max UDMA/100
ata8.00: configured for UDMA/100
scsi 7:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.21 PQ: 0 ANSI: 5
Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work
Reported-by: Sam Bingner <sam@bingner.com>
Tested-by: Sam Bingner <sam@bingner.com>
Tested-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
In quirk_huawei_pcie_sva(), device_add_properties() is used to
inject additional device properties, but there is no
device_remove_properties() call anywhere to remove those
properties. The assumption is most likely that the device is
never removed, and the properties therefore do not also never
need to be removed.
Even though it is unlikely that the device is ever removed in
this case, it is safer to make sure that the properties are
also removed if the device ever does get unregistered.
To achieve this, instead of adding a separate quirk for the
case of device removal where device_remove_properties() is
called, using device_create_managed_software_node() instead of
device_add_properties(). Both functions create a software node
(a type of fwnode) that holds the device properties, which is
then assigned to the device very much the same way.
The difference between the two functions is, that
device_create_managed_software_node() guarantees that the
software node (together with the properties) is removed when
the device is removed. The function device_add_property() does
not guarantee that, so the properties added with it should
always be removed with device_remove_properties().
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Advertise support of the Gen4 automotive variants in module's device ID
table and add the same IDs to the list of switchtec quirks.
Link: https://lore.kernel.org/r/20211119003803.2333-2-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
- Tidy setup-irq.c comments (Pranay Sanghai)
- Fix misspellings (Krzysztof Wilczyński)
- Fix sprintf(), sscanf() format mismatches (Krzysztof Wilczyński)
- Tidy cpqphp code formatting (Krzysztof Wilczyński)
- Remove unused pci_pool wrappers, which have been replaced by dma_pool
(Cai Huoqing)
- Remove a redundant initialization in __pci_reset_function_locked() (Colin
Ian King)
- Use 'unsigned int' instead of 'unsigned' (Krzysztof Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński)
- Include generic <linux/> headers instead of <asm/> for cpqphp and vmd
(Krzysztof Wilczyński)
* pci/misc:
PCI: vmd: Drop redundant includes of <asm/device.h>, <asm/msi.h>
PCI: cpqphp: Use <linux/io.h> instead of <asm/io.h>
MAINTAINERS: Update PCI subsystem information
PCI: Prefer 'unsigned int' over bare 'unsigned'
PCI: Remove redundant 'rc' initialization
PCI: Remove unused pci_pool wrappers
PCI: cpqphp: Format if-statement code block correctly
PCI: Use unsigned to match sscanf("%x") in pci_dev_str_match_path()
PCI: hv: Remove unnecessary use of %hx
PCI: Correct misspelled and remove duplicated words
PCI: Tidy comments
The Pericom PI7C9X2G404/PI7C9X2G304/PI7C9X2G303 PCIe switches have an
erratum for ACS P2P Request Redirect behaviour when used in the cut-through
forwarding mode. The recommended work around for this issue is to use the
switch in store and forward mode. The erratum results in packets being
queued and not being delivered upstream, which can be observed as very poor
downstream device performance and/or dropped device-generated
data/interrupts.
Add a fixup so that when enabling or resuming the downstream port we check
if it has enabled ACS P2P Request Redirect, and if so, change the device
(via the upstream port) to use the store and forward operating mode.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177471
Link: https://lore.kernel.org/r/20210910025823.196508-1-nathan@nathanrossi.com
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The bare "unsigned" type implicitly means "unsigned int", but the preferred
coding style is to use the complete type name.
Update the bare use of "unsigned" to the preferred "unsigned int".
No change to functionality intended.
See a1ce18e4f9 ("checkpatch: warn on bare unsigned or signed declarations
without int").
Link: https://lore.kernel.org/r/20211013014136.1117543-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Correct a number of misspelled words and remove any words that were
duplicated in the PCI tree. No change to functionality intended.
Link: https://lore.kernel.org/r/20211006233827.147328-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When passing the Atheros QCA6174 through to a virtual machine, the VM hangs
at the point where the ath10k driver loads.
Add a quirk to avoid bus resets on this device, which avoids the hang.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/08982e05-b6e8-5a8d-24ab-da1488ee50a8@web.de
Signed-off-by: Ingmar Klein <ingmar_klein@web.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Some AMD GPUs have built-in USB xHCI and USB Type-C UCSI controllers with
power dependencies between the GPU and the other functions as in
6d2e369f0d ("PCI: Add NVIDIA GPU multi-function power dependencies").
Add device link support for the AMD integrated USB xHCI and USB Type-C UCSI
controllers.
Without this, runtime power management, including GPU resume and temp and
fan sensors don't work correctly.
Reported-at: https://gitlab.freedesktop.org/drm/amd/-/issues/1704
Link: https://lore.kernel.org/r/20210903063311.3606226-1-evan.quan@amd.com
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
- Cache PCIe Device Capabilities register (Amey Narkhede)
- Add pcie_reset_flr() with 'probe' argument (Amey Narkhede)
- Add pdev->reset_methods[] array to track reset method ordering (Amey
Narkhede)
- Remove reset_fn field from pci_dev (Amey Narkhede)
- Add sysfs interface to query and set device reset mechanism (Amey
Narkhede)
- Add pci_set_acpi_fwnode() to set ACPI_COMPANION (Shanker Donthineni)
- Use acpi_pci_power_manageable() instead of duplicating logic (Shanker
Donthineni)
- Set ACPI fwnode early and at the same time with OF (Shanker Donthineni)
- Add support for ACPI _RST reset method (Shanker Donthineni)
- Change reset function 'probe' argument to bool (Amey Narkhede)
* pci/reset:
PCI: Change the type of probe argument in reset functions
PCI: Add support for ACPI _RST reset method
PCI: Setup ACPI fwnode early and at the same time with OF
PCI: Use acpi_pci_power_manageable()
PCI: Add pci_set_acpi_fwnode() to set ACPI_COMPANION
PCI: Allow userspace to query and set device reset mechanism
PCI: Remove reset_fn field from pci_dev
PCI: Add array to track reset method ordering
PCI: Add pcie_reset_flr() with 'probe' argument
PCI: Cache PCIe Device Capabilities register
HiSilicon KunPeng920 and KunPeng930 have devices that appear as PCI but are
actually on the AMBA bus. These fake PCI devices can support SVA via the
SMMU stall feature.
DT systems can indicate this in the device tree, but ACPI systems don't
have that mechanism, so add a "dma-can-stall" property manually for them.
[bhelgaas: add text from Robin as comment near quirk]
Link: https://lore.kernel.org/r/1626144876-11352-4-git-send-email-zhangfei.gao@linaro.org
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Some systems, e.g., HiSilicon KunPeng920 and KunPeng930, have devices that
appear as PCI but are actually on the AMBA bus. Some of these fake PCI
devices support a PASID-like feature and they do have a working PASID
capability even though they do not use the PCIe Transport Layer Protocol
and do not support TLP prefixes.
Add a pasid_no_tlp bit for this "PASID works without TLP prefixes" case and
update pci_enable_pasid() so it can enable PASID on these devices.
Set this bit for HiSilicon KunPeng920 and KunPeng930.
[bhelgaas: squashed, commit log]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/1626144876-11352-2-git-send-email-zhangfei.gao@linaro.org
Link: https://lore.kernel.org/r/1626144876-11352-3-git-send-email-zhangfei.gao@linaro.org
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe Address Translation Services (ATS) provides a mechanism for a device
to provide an on-device caching translation agent (device IOTLB). We
already have a means to disable support for this feature via the pci=noats
option. For untrusted and externally facing devices, we not only disable
ATS support for the device, but we use Access Control Services (ACS)
Transaction Blocking to actively prevent devices from sending TLPs with
non-default AT field values.
Extend pci=noats to also make use of PCI_ACS_TB so that not only is ATS
disabled at the device, but blocked at the downstream ports. This provides
a means to further lock-down ATS for cases such as device assignment, where
it may not be the hardware configuration of the device that makes it
untrusted, but the driver running on the device.
Link: https://lore.kernel.org/r/162404966325.2362347.12176138291577486015.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Some Cavium endpoints are implemented as multi-function devices without ACS
capability, but they actually don't support peer-to-peer transactions.
Add ACS quirks to declare DMA isolation for the following devices:
- BGX device found on Octeon-TX (8xxx)
- CGX device found on Octeon-TX2 (9xxx)
- RPM device found on Octeon-TX3 (10xxx)
Link: https://lore.kernel.org/r/20210810122425.1115156-1-george.cherian@marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com
Signed-off-by: Marcin Bachry <hegel666@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Prike Liang <prike.liang@amd.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Change the type of probe argument in functions which implement reset
methods from int to bool to make the context and intent clear.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-10-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"reset_fn" indicates whether the device supports any reset mechanism.
Remove the use of reset_fn in favor of the reset_methods array that tracks
supported reset mechanisms of a device and their ordering.
The octeon driver incorrectly used reset_fn to detect whether the device
supports FLR or not. Use pcie_reset_flr() to probe whether it supports FLR.
Co-developed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-5-ameynarkhede03@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Most reset methods are of the form "pci_*_reset(dev, probe)". pcie_flr()
was an exception because it relied on a separate pcie_has_flr() function
instead of taking a "probe" argument.
Add "pcie_reset_flr(dev, probe)" to follow the convention. Remove
pcie_has_flr().
Some pcie_flr() callers that did not use pcie_has_flr() remain.
[bhelgaas: commit log, rework pcie_reset_flr() to use dev->devcap directly]
Link: https://lore.kernel.org/r/20210817180500.1253-3-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
The ASMedia ASM1062 SATA controller advertises Max_Payload_Size_Supported
of 512, but in fact it cannot handle incoming TLPs with payload size of
512.
We discovered this issue on PCIe controllers capable of MPS = 512 (Aardvark
and DesignWare), where the issue presents itself as an External Abort.
Bjorn Helgaas says:
Probably ASM1062 reports a Malformed TLP error when it receives a data
payload of 512 bytes, and Aardvark, DesignWare, etc convert this to an
arm64 External Abort. [1]
To avoid this problem, limit the ASM1062 Max Payload Size Supported to 256
bytes, so we set the Max Payload Size of devices that may send TLPs to the
ASM1062 to 256 or less.
[1] https://lore.kernel.org/linux-pci/20210601170907.GA1949035@bjorn-Precision-5520/
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212695
Link: https://lore.kernel.org/r/20210624171418.27194-2-kabel@kernel.org
Reported-by: Rötti <espressobinboardarmbiantempmailaddress@posteo.de>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
pci_device_add() calls HEADER fixups after pci_configure_device(), which
configures Max Payload Size.
Convert MPS-related fixups to EARLY fixups so pci_configure_mps() takes
them into account.
Fixes: 27d868b5e6 ("PCI: Set MPS to match upstream bridge")
Link: https://lore.kernel.org/r/20210624171418.27194-1-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
- Add pci_reset_bus_function() Secondary Bus Reset interface (Raphael
Norwitz)
- Work around Huawei Intelligent NIC VF FLR erratum (Chiqijun)
* pci/reset:
PCI: Work around Huawei Intelligent NIC VF FLR erratum
PCI: Add pci_reset_bus_function() Secondary Bus Reset interface
The Broadcom BCM57414 NIC may be a multi-function device. While it does
not advertise an ACS capability, peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for this device so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1621645997-16251-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Observed unexpected GPU hang during runpm stress test on 0x7341 rev 0x00.
Further debugging shows broken ATS is related.
Disable ATS on this part. Similar issues on other devices:
a2da5d8cc0 ("PCI: Mark AMD Raven iGPU ATS as broken in some platforms")
45beb31d3a ("PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken")
5e89cd303e ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20210602021255.939090-1-evan.quan@amd.com
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum
time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the
FLR to complete. It assumes the FLR is complete when a config read returns
valid data.
When we do an FLR on several Huawei Intelligent NIC VFs at the same time,
firmware on the NIC processes them serially. The VF may respond to config
reads before the firmware has completed its reset processing. If we bind a
driver to the VF (e.g., by assigning the VF to a virtual machine) in the
interval between the successful config read and completion of the firmware
reset processing, the NIC VF driver may fail to load.
Prevent this driver failure by waiting for the NIC firmware to complete its
reset processing. Not all NIC firmware supports this feature.
[bhelgaas: commit log]
Link: https://support.huawei.com/enterprise/en/doc/EDOC1100063073/87950645/vm-oss-occasionally-fail-to-load-the-in200-driver-when-the-vf-performs-flr
Link: https://lore.kernel.org/r/20210414132301.1793-1-chiqijun@huawei.com
Signed-off-by: Chiqijun <chiqijun@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org
Some NVIDIA GPU devices do not work with SBR. Triggering SBR leaves the
device inoperable for the current system boot. It requires a system
hard-reboot to get the GPU device back to normal operating condition
post-SBR. For the affected devices, enable NO_BUS_RESET quirk to avoid the
issue.
This issue will be fixed in the next generation of hardware.
Link: https://lore.kernel.org/r/20210608054857.18963-8-ameynarkhede03@gmail.com
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Cc: stable@vger.kernel.org
Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS
automatically disables LTSSM when Secondary Bus Reset is received and
device stops working. Prevent bus reset for these devices. With this
change, the device can be assigned to VMs with VFIO, but it will leak state
between VMs.
Reference: https://e2e.ti.com/support/processors/f/791/t/954382
Link: https://lore.kernel.org/r/20210315102606.17153-1-antti.jarvinen@gmail.com
Signed-off-by: Antti Järvinen <antti.jarvinen@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable@vger.kernel.org
On Macbook 2013, resuming from suspend-to-idle or standby resulted in the
external monitor no longer being detected, a stacktrace, and errors like
this in dmesg:
pcieport 0000:06:00.0: can't change power state from D3hot to D0 (config space inaccessible)
The reason is that we know how to turn power to the Thunderbolt controller
*off* via the SXIO/SXFP/SXLF methods, but we don't know how to turn power
back on. We have to rely on firmware to turn the power back on.
When going to the "suspend-to-idle" or "standby" system sleep states,
firmware is not involved either on the suspend side or the resume side, so
we can't use SXIO/SXFP/SXLF to turn the power off.
Skip SXIO/SXFP/SXLF when firmware isn't involved in suspend, e.g., when
we're going to the "suspend-to-idle" or "standby" system sleep states.
Fixes: 1df5172c5c ("PCI: Suspend/resume quirks for Apple thunderbolt")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212767
Link: https://lore.kernel.org/r/20210520235501.917397-1-Hi-Angel@yandex.ru
Signed-off-by: Konstantin Kharlamov <Hi-Angel@yandex.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum
time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the
FLR to complete. It assumes the FLR is complete when a config read returns
valid data.
When we do an FLR on several Huawei Intelligent NIC VFs at the same time,
firmware on the NIC processes them serially. The VF may respond to config
reads before the firmware has completed its reset processing. If we bind a
driver to the VF (e.g., by assigning the VF to a virtual machine) in the
interval between the successful config read and completion of the firmware
reset processing, the NIC VF driver may fail to load.
Prevent this driver failure by waiting for the NIC firmware to complete its
reset processing. Not all NIC firmware supports this feature.
[bhelgaas: commit log]
Link: https://support.huawei.com/enterprise/en/doc/EDOC1100063073/87950645/vm-oss-occasionally-fail-to-load-the-in200-driver-when-the-vf-performs-flr
Link: https://lore.kernel.org/r/20210414132301.1793-1-chiqijun@huawei.com
Signed-off-by: Chiqijun <chiqijun@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Mika Westerberg