- Allow host controller driver to probe successfully (as other drivers do)
even if link is currently down (Fabio Estevam)
- Enable i.MX6QP PCIe power management (Richard Zhu)
- Invoke PHY exit function after PHY power off (Richard Zhu)
- Assert i.MX8MM CLKREQ# even if no device present to avoid boot hangs
(Richard Zhu)
* remotes/lorenzo/pci/imx6:
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: imx6: Enable i.MX6QP PCIe power management support
PCI: imx6: Allow to probe when dw_pcie_wait_for_link() fails
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe to workaround enumeration issue on
SiFive Unmatched board (Ben Dooks)
* pci/host/fu740:
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
fu740_pcie_host_init() assigned "ret", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-fu740.c:227 Variable 'ret' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
hi3660_pcie_phy_init() assigned "pdev", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-kirin.c:336 Variable 'pdev' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The fu740 PCIe core does not probe any devices on the SiFive Unmatched
board without this fix (or having U-Boot explicitly start the PCIe via
either boot-script or user command). The fix is to start the link at
2.5GT/s speeds and once the link is up then change the maximum speed back
to the default.
The U-Boot driver claims to set the link-speed to 2.5GT/s to get the probe
to work (and U-Boot does print link up at 2.5GT/s) in the following code:
https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/pci/pcie_dw_sifive.c?id=v2022.01#L271
Link: https://lore.kernel.org/r/20220318152430.526320-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
The CLKREQ# signal is an open drain, active low signal that is driven
low by the remote Endpoint device. But it might not be driven low if no
Endpoint device is connected.
On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no
Endpoint is connected to assert CLKREQ#.
Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the
PHY can be initialized.
Link: https://lore.kernel.org/r/1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
To balance phy->init_count, invoke the phy_exit() after phy_power_off().
Link: https://lore.kernel.org/r/1646289275-17813-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
If a host that uses the IP's integrated MSI Receiver lost power
during suspend, we call dw_pcie_setup_rc() to reinit the RC. But
dw_pcie_setup_rc() always sets pp->irq_mask[ctrl] to ~0, so the mask
register is always set as 0xffffffff incorrectly, thus the MSI can't
work after resume.
Fix this issue by moving pp->irq_mask[ctrl] initialization to
dw_pcie_host_init() so we can correctly set the mask reg during both
boot and resume.
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20211226074019.2556-1-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The calls to devm_gpiod_get_optional() have the -gpios at the end of the
name but the GPIO core code is already adding the suffix during the lookup.
This means the PCIe driver is not finding the necessary reset or power
lines to allow initialisation of the PCIe.
Drop the redundant '-gpios' when we look up GPIOs from the DT.
This bug has not been noticed because if U-Boot has setup the GPIO lines
for the hardware when it does the PCIe initialisation (either by booting
from PCIe or user command to access PCIe) then the PCIe will work in Linux.
The U-Boot as supplied by SiFive does not by default initialise any PCIe
component.
Link: https://lore.kernel.org/r/20220221210347.1335004-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
i.MX6QP PCIe supports the reset logic, thus it can reset itself to the
initialized state when exit from L2 or L3 states.
Enable the i.MX6QP PCIe suspend/resume operations support.
Link: https://lore.kernel.org/r/1645425237-4071-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
On SM8450 platform PCIe hosts do not use all the clocks (and add several
additional clocks), so expand the driver to handle these requirements.
PCIe0 and PCIe1 hosts use different sets of clocks, so separate entries
are required.
Link: https://lore.kernel.org/r/20220223101435.447839-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Qualcomm PCIe driver uses compatible string to check if the ddrss_sf_tbu
clock should be used. Since sc7280 support has added flags, switch to
the new mechanism to check if this clock should be used.
Link: https://lore.kernel.org/r/20220223101435.447839-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
In preparation to adding more flags to configuration data, use pointer
to struct qcom_pcie_cfg directly inside struct qcom_pcie, rather than
duplicating all its fields. This would save us from the boilerplate code
that just copies flag values from one struct to another one.
Link: https://lore.kernel.org/r/20220223101435.447839-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Add these PCI class codes to pci_ids.h:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
Use these defines in all kernel code for describing PCI class codes for
normal and subtractive PCI bridges.
[bhelgaas: similar change in pci-mvebu.c]
Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add basic support for UniPhier NX1 SoC as non-legacy SoC. This includes
a compatible string, SoC-dependent data containing init() and wait()
functions for the controller.
Link: https://lore.kernel.org/r/1644480596-20037-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Define SoC data structure that includes pci_epc_features, SoC-dependent
callback functions and flags to distinguish the behavior of each SoC.
The callback functions define init() to initialize the controller and
wait() to wait until initialization is completed.
Rename uniphier_pcie_init_ep() to uniphier_pcie_pro5_init_ep() for
initializing PCIe controller implemented in Pro5 SoC. And Pro5 SoC
doesn't have wait() function.
Link: https://lore.kernel.org/r/1644480596-20037-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Bean reported that a622435fbe ("PCI: kirin: Prefer
of_device_get_match_data()") broke kirin_pcie_probe() because it assumed
match data of 0 was a failure when in fact, it meant the match data was
"(void *)PCIE_KIRIN_INTERNAL_PHY".
Therefore, probing of "hisilicon,kirin960-pcie" devices failed with -EINVAL
and an "OF data missing" message.
Add a struct kirin_pcie_data to encode the PHY type. Then the result of
of_device_get_match_data() should always be a non-NULL pointer to a struct
kirin_pcie_data that contains the PHY type.
Fixes: a622435fbe ("PCI: kirin: Prefer of_device_get_match_data()")
Link: https://lore.kernel.org/r/20220202162659.GA12603@bhelgaas
Link: https://lore.kernel.org/r/20220201215941.1203155-1-huobean@gmail.com
Reported-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The intention of commit 886a9c1347 ("PCI: dwc: Move link handling into
common code") was to standardize the behavior of link down as explained
in its commit log:
"The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device."
The pci-imx6 still fails to probe when the link is not present, which
causes the following warning:
imx6q-pcie 8ffc000.pcie: Phy link never came up
imx6q-pcie: probe of 8ffc000.pcie failed with error -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 30 at drivers/regulator/core.c:2257 _regulator_put.part.0+0x1b8/0x1dc
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:2 Not tainted 5.15.0-next-20211103 #1
Hardware name: Freescale i.MX6 SoloX (Device Tree)
Workqueue: events_unbound async_run_entry_fn
[<c0111730>] (unwind_backtrace) from [<c010bb74>] (show_stack+0x10/0x14)
[<c010bb74>] (show_stack) from [<c0f90290>] (dump_stack_lvl+0x58/0x70)
[<c0f90290>] (dump_stack_lvl) from [<c012631c>] (__warn+0xd4/0x154)
[<c012631c>] (__warn) from [<c0f87b00>] (warn_slowpath_fmt+0x74/0xa8)
[<c0f87b00>] (warn_slowpath_fmt) from [<c076b4bc>] (_regulator_put.part.0+0x1b8/0x1dc)
[<c076b4bc>] (_regulator_put.part.0) from [<c076b574>] (regulator_put+0x2c/0x3c)
[<c076b574>] (regulator_put) from [<c08c3740>] (release_nodes+0x50/0x178)
Fix this problem by ignoring the dw_pcie_wait_for_link() error like
it is done on the other dwc drivers.
Tested on imx6sx-sdb and imx6q-sabresd boards.
Link: https://lore.kernel.org/r/20220106103645.2790803-1-festevam@gmail.com
Fixes: 886a9c1347 ("PCI: dwc: Move link handling into common code")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: <stable@vger.kernel.org>
-----BEGIN PGP SIGNATURE-----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=RKW4
-----END PGP SIGNATURE-----
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
-----BEGIN PGP SIGNATURE-----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=Vgg4
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups
(Greg Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum
(Rajat Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
Resource management:
- Always write Intel I210 ROM BAR on update to work around device
defect (Bjorn Helgaas)
PCIe native device hotplug:
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas
Wunner)
Power management:
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power
management to generic power management (Vaibhav Gupta)
IOMMU:
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
so it can work with an IOMMU (Yifeng Li)
Error handling:
- Add PCI_ERROR_RESPONSE and related definitions for signaling and
checking for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers,
instead of in host controller drivers, when transactions fail on
PCI (Naveen Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config
reads (Naveen Naidu)
Peer-to-peer DMA:
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
ASPM:
- Calculate link L0s and L1 exit latencies when needed instead of
caching them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed
instead of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
APM X-Gene PCIe controller driver:
- Fix IB window setup, which was broken by the fact that IB resources
are now sorted in address order instead of DT dma-ranges order (Rob
Herring)
Apple PCIe controller driver:
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
Broadcom STB PCIe controller driver:
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors
and not fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding
(Jim Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected
devices (Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is
added or removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup
devices (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Use DWC common ops instead of layerscape-specific link-up functions
(Hou Zhiqiang)
Intel VMD host bridge driver:
- Honor platform ACPI _OSC feature negotiation for Root Ports below
VMD (Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
- Reset everything below VMD before enumerating to work around
failure to enumerate NVMe devices when guest OS reboots (Nirmal
Patel)
Bridge emulation (used by Marvell Aardvark and MVEBU):
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali
Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they
must have at least a PCIe Capability (Pali Rohár)
Marvell Aardvark PCIe controller driver:
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2,
DEVSTA2, LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali
Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
registers (Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali
Rohár)
- Mask all interrupts when unbinding host controller driver (Pali
Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali
Rohár)
- Disable common PHY when unbinding host controller driver (Pali
Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the ARM
implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali
Rohár)
- Disable Root Port windows when base/limit set to invalid values
(Pali Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect
the actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root
Ports (Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports
(Pali Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on
Armada XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module
(Pali Rohár)
- Add support for compiling as a module (Pali Rohár)
MediaTek PCIe controller driver:
- Assert PERST# for 100ms to allow power and clock to stabilize
(qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to
respond to the request causes failure to exit L1 PM Substate
(Jianjun Wang)
MediaTek MT7621 PCIe controller driver:
- Declare mt7621_pci_ops static (Sergio Paracuellos)
- Give pcibios_root_bridge_prepare() access to host bridge windows
(Sergio Paracuellos)
- Move MIPS I/O coherency unit setup from driver to
pcibios_root_bridge_prepare() (Sergio Paracuellos)
- Add missing MODULE_LICENSE() (Sergio Paracuellos)
- Allow COMPILE_TEST for all arches (Sergio Paracuellos)
Microsoft Hyper-V host bridge driver:
- Add hv-internal interfaces to encapsulate arch IRQ dependencies
(Sunil Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
Qualcomm PCIe controller driver:
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16()
(Manivannan Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
Renesas R-Car PCIe controller driver:
- Fix aarch32 abort handler so it doesn't check the wrong bus clock
before accessing the host controller (Marek Vasut)
TI Keystone PCIe controller driver:
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode
DT properties (Kishon Vijay Abraham I)
MicroSemi Switchtec management driver:
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and
initialized for every call (Kelvin Cao)
Host controller driver cleanups:
- Use of_device_get_match_data(), not of_match_device(), when we only
need the device data in altera, artpec6, cadence, designware-plat,
dra7xx, keystone, kirin (Fan Fei)
- Drop pointless of_device_get_match_data() cast in j721e (Bjorn
Helgaas)
- Drop redundant struct device * from j721e since struct cdns_pcie
already has one (Bjorn Helgaas)
- Rename driver structs to *_pcie in intel-gw, iproc, ls-gen4,
mediatek-gen3, microchip, mt7621, rcar-gen2, tegra194, uniphier,
xgene, xilinx, xilinx-cpm for consistency across drivers (Fan Fei)
- Fix invalid address space conversions in hisi, spear13xx (Bjorn
Helgaas)
Miscellaneous:
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming
Wang)"
* tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (151 commits)
PCI: mt7621: Allow COMPILE_TEST for all arches
PCI: mt7621: Add missing MODULE_LICENSE()
PCI: mt7621: Move MIPS setup to pcibios_root_bridge_prepare()
PCI: Let pcibios_root_bridge_prepare() access bridge->windows
PCI: mt7621: Declare mt7621_pci_ops static
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
misc: pci_endpoint_test: Terminate statement with semicolon
...
find_first{,_zero}_bit is a more effective analogue of 'next' version if
start == 0. This patch replaces 'next' with 'first' where things look
trivial.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
- Add PCI_ERROR_RESPONSE and related definitions for signaling and checking
for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers, instead
of in host controller drivers, when transactions fail on PCI (Naveen
Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config reads
(Naveen Naidu)
* pci/errors:
PCI: xgene: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: hv: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: keystone: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: Use PCI_ERROR_RESPONSE to identify config read errors
PCI: cpqphp: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/PME: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/DPC: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: pciehp: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: vmd: Use PCI_POSSIBLE_ERROR() to check config reads
PCI/ERR: Use PCI_POSSIBLE_ERROR() to check config reads
PCI: rockchip-host: Drop error data fabrication when config read fails
PCI: rcar-host: Drop error data fabrication when config read fails
PCI: altera: Drop error data fabrication when config read fails
PCI: mvebu: Drop error data fabrication when config read fails
PCI: aardvark: Drop error data fabrication when config read fails
PCI: kirin: Drop error data fabrication when config read fails
PCI: histb: Drop error data fabrication when config read fails
PCI: exynos: Drop error data fabrication when config read fails
PCI: mediatek: Drop error data fabrication when config read fails
PCI: iproc: Drop error data fabrication when config read fails
PCI: thunder: Drop error data fabrication when config read fails
PCI: Drop error data fabrication when config read fails
PCI: Use PCI_SET_ERROR_RESPONSE() for disconnected devices
PCI: Set error response data when config read fails
PCI: Add PCI_ERROR_RESPONSE and related definitions
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16() (Manivannan
Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
* remotes/lorenzo/pci/qcom:
PCI: qcom-ep: Constify static dw_pcie_ep_ops
PCI: qcom: Use __be16 type to store return value from cpu_to_be16()
PCI: qcom: Fix an error handling path in 'qcom_pcie_probe()'
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode DT
properties (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
PCI: keystone: Use phandle argument from "ti,syscon-pcie-id"/"ti,syscon-pcie-mode"
dt-bindings: PCI: ti,am65: Fix "ti,syscon-pcie-id"/"ti,syscon-pcie-mode" to take argument
Get "syscon" pcie_mode and pcie_id offset from the argument of
"ti,syscon-pcie-id" and "ti,syscon-pcie-mode" phandle respectively.
Previously a subnode to "syscon" node was added which has the
exact memory mapped address of pcie_mode and pcie_id but now the
offset of pcie_mode and pcie_id within "syscon" is now being passed
as argument to "ti,syscon-pcie-id" and "ti,syscon-pcie-mode" phandle.
If the offset is not provided in "ti,syscon-pcie-id"/"ti,syscon-pcie-mode",
the full memory mapped address of pcie_ctrl is used in order to maintain
old DT compatibility.
Similar change for J721E is as discussed in [1]
[1] -> http://lore.kernel.org/r/CAL_JsqKiUcO76bo1GoepWM1TusJWoty_BRy2hFSgtEVMqtrvvQ@mail.gmail.com
Link: https://lore.kernel.org/r/20211126083119.16570-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The current Layerscape PCIe driver directly uses the physical layer
LTSSM code to check the link-up state, which treats the > L0 states
as link-up. This is not correct, since there is not explicit map
between link-up state and LTSSM. So this patch changes to use the
DWC common link-up check function.
Link: https://lore.kernel.org/r/20211224094000.8513-1-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The only usage of pci_ep_ops is to assign its address to the ops field
in the dw_pcie_ep struct which is a pointer to const struct dw_pcie_ep_ops.
Make it const to allow the compiler to put it in read-only memory.
Link: https://lore.kernel.org/r/20211204220316.88655-1-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
The sparse checker complains about converting pointers between address
spaces. We correctly stored an __iomem pointer in struct spear13xx_pcie,
but discarded the __iomem when extracting app_base, causing one warning.
Then we passed the non-__iomem pointer to writel(), which expects an
__iomem pointer, causing another warning.
Add the appropriate annotations.
The sparse warnings look like this:
$ make C=2 drivers/pci/controller/
drivers/pci/controller/dwc/pcie-spear13xx.c:72:54: warning: incorrect type in initializer (different address spaces)
drivers/pci/controller/dwc/pcie-spear13xx.c:72:54: expected struct pcie_app_reg *app_reg
drivers/pci/controller/dwc/pcie-spear13xx.c:72:54: got void [noderef] __iomem *app_base
drivers/pci/controller/dwc/pcie-spear13xx.c:78:26: warning: incorrect type in argument 2 (different address spaces)
drivers/pci/controller/dwc/pcie-spear13xx.c:78:26: expected void volatile [noderef] __iomem *addr
drivers/pci/controller/dwc/pcie-spear13xx.c:78:26: got unsigned int *
Link: https://lore.kernel.org/r/20211223213749.1314142-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
The sparse checker complains about converting pointers between address
spaces. The pci_config_window.priv pointer is a generic void *, but
hisi_pcie_map_bus() needs a void __iomem *.
This isn't a problem in other drivers because they store the __iomem
pointer in a driver struct. Add a trivial struct hisi_pcie to avoid the
warning.
The sparse warning looks like this:
$ make C=2 drivers/pci/controller/
drivers/pci/controller/dwc/pcie-hisi.c:61:37: warning: incorrect type in initializer (different address spaces)
drivers/pci/controller/dwc/pcie-hisi.c:61:37: expected void [noderef] __iomem *reg_base
drivers/pci/controller/dwc/pcie-hisi.c:61:37: got void *priv
Link: https://lore.kernel.org/r/20211223213749.1314142-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Rename struct uniphier_pcie_priv to uniphier_pcie to match the convention
of <driver>_pcie. No functional change intended.
[bhelgaas: drop extraneous uniphier_pcie_irq_ack() from patch]
Link: https://lore.kernel.org/r/20211223011054.1227810-21-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Rename tegra_pcie_dw to tegra194_pcie to match the convention of
<driver>_pcie. No functional change intended.
[bhelgaas: rename functions similarly]
Link: https://lore.kernel.org/r/20211223011054.1227810-20-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Rename struct intel_pcie_port to intel_pcie to match the convention of
<driver>_pcie. No functional change intended.
Link: https://lore.kernel.org/r/20211223011054.1227810-11-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rahul Tanwar <rtanwar@maxlinear.com>
The kirin driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-8-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
The keystone driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-7-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
The dra7xx driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-6-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
The designware-plat driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-5-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The artpec6 driver only needs the device data, not the whole struct
of_device_id. Use of_device_get_match_data() instead of of_match_device().
No functional change intended.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211223011054.1227810-3-helgaas@kernel.org
Signed-off-by: Fan Fei <ffclaire1224@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
i.MX8MM PCIe works mostly like the i.MX8MQ one, but has a different PHY
and allows to output the internal PHY reference clock via the refclk pad.
Add the i.MX8MM PCIe support based on the standalone PHY driver.
Link: https://lore.kernel.org/r/1640312885-31142-2-git-send-email-hongxing.zhu@nxp.com
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
cpu_to_be16() returns __be16 value but the driver uses u16 and that's
incorrect. Fix it by using __be16 as the data type of bdf_be variable.
The issue was spotted by the below sparse warning:
sparse warnings: (new ones prefixed by >>)
>> drivers/pci/controller/dwc/pcie-qcom.c:1305:30: sparse: sparse: incorrect type in initializer (different base types) @@ expected unsigned short [usertype] bdf_be @@ got restricted __be16 [usertype] @@
drivers/pci/controller/dwc/pcie-qcom.c:1305:30: sparse: expected unsigned short [usertype] bdf_be
drivers/pci/controller/dwc/pcie-qcom.c:1305:30: sparse: got restricted __be16 [usertype]
Link: https://lore.kernel.org/r/20211130080924.266116-1-manivannan.sadhasivam@linaro.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
cgroup.h (therefore swap.h, therefore half of the universe)
includes bpf.h which in turn includes module.h and slab.h.
Since we're about to get rid of that dependency we need
to clean things up.
v2: drop the cpu.h include from cacheinfo.h, it's not necessary
and it makes riscv sensitive to ordering of include files.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: SeongJae Park <sj@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/all/20211120035253.72074-1-kuba@kernel.org/ # v1
Link: https://lore.kernel.org/all/20211120165528.197359-1-kuba@kernel.org/ # cacheinfo discussion
Link: https://lore.kernel.org/bpf/20211202203400.1208663-1-kuba@kernel.org
On imx6 and perhaps others when pcie probes you get a:
imx6q-pcie 33800000.pcie: invalid resource
This occurs because the atu is not specified in the DT and as such it
should not be remapped.
Link: https://lore.kernel.org/r/20211101180243.23761-1-tharvey@gateworks.com
Fixes: 281f1f99cf ("PCI: dwc: Detect number of iATU windows")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
If 'of_device_get_match_data()' fails, previous 'pm_runtime_get_sync()/
pm_runtime_enable()' should be undone.
To fix it, the easiest is to move this block of code before the memory
allocations and the pm_runtime_xxx calls.
Link: https://lore.kernel.org/r/4d03c636193f64907c8dacb17fa71ed05fd5f60c.1636220582.git.christophe.jaillet@wanadoo.fr
Fixes: b89ff41025 ("PCI: qcom: Replace ops with struct pcie_cfg in pcie match data")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/f87e22bc09a471d2cf15ad05dfd6432f57739aed.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/7da7ea760abc5f85cad6e9b0d3e59eebd93f50d3.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/765c2f27d85fcee4eb137023dc0a8f864eee9e36.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Reorganize to separate out PHY logic (Mauro Carvalho Chehab)
- Add support for external PHY in addition to the internal PHY (Mauro
Carvalho Chehab)
- Use regmap so both kirin driver and PHY can access APB registers (Mauro
Carvalho Chehab)
- Add support for per-lane PERST# GPIOs on HiKey970 external PEX 8606 PCI
bridge (Mauro Carvalho Chehab)
- Add "hisilicon,kirin970-pcie" compatible string (Mauro Carvalho Chehab)
- Add MODULE_* macros (Mauro Carvalho Chehab)
- Allow building as a module (Mauro Carvalho Chehab)
- Add power_off support for Kirin 960 PHY (Mauro Carvalho Chehab)
- Disable clkreq during poweroff sequence (Mauro Carvalho Chehab)
- De-init the dwc driver during remove (Mauro Carvalho Chehab)
- Allow removal of kirin driver (Mauro Carvalho Chehab)
* pci/host/kirin:
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: kirin: Use regmap for APB registers
PCI: kirin: Add support for a PHY layer
PCI: kirin: Reorganize the PHY logic inside the driver
Now that everything is in place at the poweroff sequence, this driver can
use module_platform_driver(), which allows it to be removed.
Link: https://lore.kernel.org/r/53b40494252444a9b830827922c4e3a301b8f863.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic under .remove ops is missing a call to dw_pcie_host_deinit(). Add
it, in order to allow the DWC core to be properly cleaned up.
Link: https://lore.kernel.org/r/838621e1c84ebaac153ccd9c36ea5e1254c61ead.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic at kirin_pcie_gpio_request() enables some clkreq GPIO lines.
Disable them during power-off.
Link: https://lore.kernel.org/r/f403e590843de1a581cade2d534d34715706f54e.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Instead of having two copies of the same logic, place the power-off logic
in a separate function.
No functional changes.
Link: https://lore.kernel.org/r/64f6e8da3e5fff38b6c8fcb208ace46efe6555bb.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
There's nothing preventing this driver from being loaded as a module.
Change its config from bool to tristate.
Link: https://lore.kernel.org/r/b5e7cfe9df09b492750bd6db0f0c911eaae8c2d4.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The PHY layer need to access APB registers too, for Kirin 970. So place
them into a named regmap.
Link: https://lore.kernel.org/r/daf0e4bda5a69a5ac8484e70f09351a959805c8c.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The pcie-kirin driver contains both PHY and generic PCI driver.
The best would be, instead, to support a PCI PHY driver, making the driver
more generic.
However, it is too late to remove the Kirin 960 PHY, as a change like that
would make the DT schema incompatible with past versions.
So, add support for an external PHY driver without removing the existing
Kirin 960 PHY from it.
Link: https://lore.kernel.org/r/f38361df2e9d0dc5a38ff942b631f7fef64cdc12.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The pcie-kirin PCIe driver contains internally a PHY interface for
Kirin 960.
As the next patches will add support for using an external PHY driver,
reorganize the driver in a way that the PHY part will be self-contained.
This could be moved to a separate PHY driver, but a change like that would
mean a non-backward-compatible DT schema change.
Link: https://lore.kernel.org/r/ad2f4aa6bbb71d5c9af0139704672f75f12644fc.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
On the SC7280, the clock source for gcc_pcie_1_pipe_clk_src must be the
TCXO while gdsc is enabled. After PHY init successful clock source should
switch to pipe clock for gcc_pcie_1_pipe_clk_src.
Link: https://lore.kernel.org/r/1633628923-25047-6-git-send-email-pmaliset@codeaurora.org
Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Add struct qcom_pcie_cfg as match data for all platforms. Assign
appropriate platform ops into struct qcom_pcie_cfg and read using
of_device_get_match_data() in qcom_pcie_probe().
Link: https://lore.kernel.org/r/1633628923-25047-5-git-send-email-pmaliset@codeaurora.org
Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
On the Qualcomm sc8180x platform the bootloader does something related
to PCI that leaves a pending "msi" interrupt, which with the current
ordering often fires before init has a chance to enable the clocks that
are necessary for the interrupt handler to access the hardware.
Move the host_init() call before the registration of the "msi" interrupt
handler to ensure the host driver has a chance to enable the clocks.
The assignment of the bridge's ops and child_ops is moved along, because
at least the TI Keystone driver overwrites these in its host_init
callback.
Link: https://lore.kernel.org/r/20210823154958.305677-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add driver for Qualcomm PCIe Endpoint controller based on the DesignWare
core with added Qualcomm-specific wrapper around the core. The driver
support is very basic such that it supports only enumeration, PCIe
read/write, and MSI. There is no ASPM and PM support for now but these will
be added later.
The driver is capable of using the PERST# and WAKE# side-band GPIOs for
operation and written on top of the DWC PCI framework.
[bhelgaas: wrap a few long lines]
Co-developed-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: restructured the driver and fixed several bugs for upstream]
Link: https://lore.kernel.org/r/20210920065946.15090-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Clean up the users of PCIE_DW_EP and introduce idiom
depends on PCI_ENDPOINT
select PCIE_DW_EP
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Furthermore, there is no need to repeat menu dependencies (PCI).
Clean up the users of PCIE_DW_HOST and introduce idiom
depends on PCI_MSI_IRQ_DOMAIN
select PCIE_DW_HOST
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Previously, the maximum link speed was set following an "fsl,max-link-speed"
property read, and should the read failed, then the PCIe generation was
manually set to PCIe Gen1 and thus limiting the link speed to 2.5 GT/s.
Code refactoring completed in the commit 39bc500650 ("PCI: dwc:
Centralize link gen setting") changed to the logic that was previously
used to limit the maximum link speed leaving behind an unused assignment
to a variable "ret".
Since the value returned from the of_property_read_u32() and stored in
the variable "ret" is never used in any meaningful way, and it's also
immediately reassigned in the code that follows, the assignment can be
removed.
Link: https://lore.kernel.org/r/20211003025439.84783-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
If the clock is provided externally we need to make sure it is enabled
before starting PCI scan.
Link: https://lore.kernel.org/r/20210531085934.2662457-5-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Unused since commit e259c2926c ("PCI: pci-dra7xx: Prepare for deferred
probe with module_platform_driver").
Link: https://lore.kernel.org/r/20210531085934.2662457-4-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable building the driver as a loadable kernel module.
Link: https://lore.kernel.org/r/20210531085934.2662457-3-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
These symbols are used by the pci-dra7xx driver. Export them to allow
building pci-dra7xx as a module.
Link: https://lore.kernel.org/r/20210531085934.2662457-2-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
- Add max-virtual-functions to endpoint binding (Kishon Vijay Abraham I)
- Add pci_epf_add_vepf() API to add virtual function to endpoint (Kishon
Vijay Abraham I)
- Add pci_epf_vepf_link() to link virtual function to endpoint physical
function (Kishon Vijay Abraham I)
- Add virtual function number to pci_epc_ops endpoint ops interfaces
(Kishon Vijay Abraham I)
- Simplify register base address computation for endpoint BAR configuration
(Kishon Vijay Abraham I)
- Add support to configure virtual functions in cadence endpoint driver
(Kishon Vijay Abraham I)
- Add SR-IOV configuration to endpoint test driver (Kishon Vijay Abraham I)
- Document configfs usage to create virtual functions for endpoints (Kishon
Vijay Abraham I)
* remotes/lorenzo/pci/endpoint:
Documentation: PCI: endpoint/pci-endpoint-cfs: Guide to use SR-IOV
misc: pci_endpoint_test: Populate sriov_configure ops to configure SR-IOV device
PCI: cadence: Add support to configure virtual functions
PCI: cadence: Simplify code to get register base address for configuring BAR
PCI: endpoint: Add virtual function number in pci_epc ops
PCI: endpoint: Add support to link a physical function to a virtual function
PCI: endpoint: Add support to add virtual function in endpoint core
dt-bindings: PCI: pci-ep: Add binding to specify virtual function
Add a driver for the DesignWare-based PCIe controller found on
RK356X. The existing pcie-rockchip-host driver is only used for
the Rockchip-designed IP found on RK3399.
Link: https://lore.kernel.org/r/20210625065511.1096935-1-xxm@rock-chips.com
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
dw_plat_add_pcie_ep() was removed and the call to the dw_pcie_ep_init() was
moved into dw_plat_pcie_probe().
This left a break statement behind that is not needed any more as as
dw_plat_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701210252.1638709-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The switch statement in the artpec6_pcie_probe() has a local code block
where "val" is defined and immediately used by the artpec6_pcie_readl().
This extra code block adds brackets at the same indentation level as the
switch statement itself which can hinder readability of the code.
Move the "val" declaration to the top of the function and remove
the extra code block from the switch statement.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701204401.1636562-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
artpec6_add_pcie_ep() was removed and the call to the dw_pcie_ep_init()
was moved into artpec6_pcie_probe().
This left a break statement behind that is not needed any more as
artpec6_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Link: https://lore.kernel.org/r/20210701204401.1636562-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Add support for the PCIe RC controller on Toshiba Visconti ARM SoCs. This
PCIe controller is based on the Synopsys DesignWare PCIe core.
Link: https://lore.kernel.org/r/20210811083830.784065-3-nobuhiro1.iwamatsu@toshiba.co.jp
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add driver for Intel Keem Bay SoC PCIe controller. This controller
is based on DesignWare PCIe core.
In Root Complex mode, only internal reference clock is possible for
Keem Bay A0. For Keem Bay B0, external reference clock can be used
and will be the default configuration. Currently, keembay_pcie_of_data
structure has one member. It will be expanded later to handle this
difference.
Endpoint mode link initialization is handled by the boot firmware.
Link: https://lore.kernel.org/r/20210805211010.29484-3-srikanth.thokala@intel.com
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add virtual function number in pci_epc ops. EPC controller driver
can perform virtual function specific initialization based on the
virtual function number.
Link: https://lore.kernel.org/r/20210819123343.1951-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When Tegra PCIe is in endpoint mode it should be available for root port.
PCIe link up by root port fails if it is in suspend state. So, don't allow
Tegra to suspend when endpoint mode is enabled.
Link: https://lore.kernel.org/r/20210623100525.19944-5-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In suspend_noirq() call if link doesn't goto L2, PERST# is asserted
to bring link to detect state. However, this is causing surprise
link down AER error. Since Kernel is executing noirq suspend calls,
AER interrupt is not processed. PME and AER are shared interrupts
and PCIe subsystem driver enables wake capability of PME irq during
suspend. So this AER will cause suspend failure due to pending
AER interrupt.
After PCIe link is in L2, interrupts are not expected since PCIe
controller will be in reset state. Disable PCIe interrupts before
going to L2 state to avoid pending AER interrupt.
Link: https://lore.kernel.org/r/20210623100525.19944-4-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Lower order MSI-X address is programmed in MSIX_ADDR_MATCH_HIGH_OFF
DBI register instead of higher order address. This patch fixes this
programming mistake.
Link: https://lore.kernel.org/r/20210623100525.19944-3-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
In tegra_pcie_ep_hard_irq(), APPL_INTR_STATUS_L0 is stored in val and again
APPL_INTR_STATUS_L1_0_0 is also stored in val. So when execution reaches
"if (val & APPL_INTR_STATUS_L0_PCI_CMD_EN_INT)", val is not correct.
Link: https://lore.kernel.org/r/20210623100525.19944-2-omp@nvidia.com
Signed-off-by: Om Prakash Singh <omp@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Wherever possible, replace constructs that match either
generic_handle_irq(irq_find_mapping()) or
generic_handle_irq(irq_linear_revmap()) to a single call to
generic_handle_domain_irq().
Link: https://lore.kernel.org/r/20210802162630.2219813-4-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 275e88b06a ("PCI: tegra: Fix host link initialization") broke
host initialization during resume as it misses out calling the API
dw_pcie_setup_rc() which is required for host and MSI initialization.
Link: https://lore.kernel.org/r/20210504172157.29712-1-vidyas@nvidia.com
Fixes: 275e88b06a ("PCI: tegra: Fix host link initialization")
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The i.MX8MQ PCIe PHY needs 1.8V in default but can be supplied by either a
1.8V or a 3.3V regulator.
The "vph-supply" DT property tells us which external regulator supplies the
PHY. If that regulator supplies anything over 3V, enable the PHY's internal
3.3V-to-1.8V regulator.
Link: https://lore.kernel.org/r/1622771269-13844-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Define the length of the DBI registers and limit config space to its
length. This makes sure that the kernel does not access registers beyond
that point that otherwise would lead to an abort on the i.MX 6QuadPlus.
See commit 075af61c19 ("PCI: imx6: Limit DBI register length") that
resolves a similar issue on the i.MX 6Quad PCIe.
Link: https://lore.kernel.org/r/1613789388-2495-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
When devm_ioremap_resource() fails, __devm_ioremap_resource() prints an
error message including the device name, failure cause, and possibly
resource information.
Remove the error message from imx6_pcie_probe() since it's redundant.
Link: https://lore.kernel.org/r/20210511114547.5601-1-thunder.leizhen@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
The legacy PCI interrupt lines need to be enabled using PCIE_APP_IRNEN bits
13 (INTA), 14 (INTB), 15 (INTC) and 16 (INTD). The old code however was
taking (for example) "13" as raw value instead of taking BIT(13). Define
the legacy PCI interrupt bits using the BIT() macro and then use these in
PCIE_APP_IRN_INT.
Link: https://lore.kernel.org/r/20210106135540.48420-1-martin.blumenstingl@googlemail.com
Fixes: ed22aaaede ("PCI: dwc: intel: PCIe RC controller driver")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rahul Tanwar <rtanwar@maxlinear.com>
7f10074474 ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
caused a few build regressions:
- 7f10074474 removed the Makefile rule for CONFIG_PCIE_TEGRA194, so
pcie-tegra.c can no longer be built as a module. Restore that rule.
- 7f10074474 added "#ifdef CONFIG_PCIE_TEGRA194" around the native
driver, but that's only set when the driver is built-in (for a module,
CONFIG_PCIE_TEGRA194_MODULE is defined).
The ACPI quirk is completely independent of the rest of the native
driver, so move the quirk to its own file and remove the #ifdef in the
native driver.
- 7f10074474 added symbols that are always defined but used only when
CONFIG_PCIEASPM, which causes warnings when CONFIG_PCIEASPM is not set:
drivers/pci/controller/dwc/pcie-tegra194.c:259:18: warning: ‘event_cntr_data_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:250:18: warning: ‘event_cntr_ctrl_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:243:27: warning: ‘pcie_gen_freq’ defined but not used [-Wunused-const-variable=]
Fixes: 7f10074474 ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
Link: https://lore.kernel.org/r/20210610064134.336781-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
- Use generic config accessors for TI AM65x (K3) to fix regression (Kishon
Vijay Abraham I)
- Move MSI Receiver init to dw_pcie_host_init() so it is re-initialized
along with the RC in resume (Jisheng Zhang)
- Remove unused pcie_app_rd() (Jiapeng Chong)
- Move iATU detection earlier to fix regression (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Move iATU detection earlier
PCI: dwc/intel-gw: Remove unused function
PCI: dwc: Move dw_pcie_msi_init() to dw_pcie_setup_rc()
PCI: keystone: Let AM65 use the pci_ops defined in pcie-designware-host.c
Add driver for the SiFive FU740 PCIe host controller.
This controller is based on the DesignWare PCIe core.
Co-developed-by: Henry Styles <hes@sifive.com>
Co-developed-by: Erik Danie <erik.danie@sifive.com>
Co-developed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20210504105940.100004-6-greentime.hu@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Henry Styles <hes@sifive.com>
Signed-off-by: Erik Danie <erik.danie@sifive.com>
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
dw_pcie_ep_init() depends on the detected iATU region numbers to allocate
the in/outbound window management bitmap. It fails after 281f1f99cf
("PCI: dwc: Detect number of iATU windows").
Move the iATU region detection into a new function, move the detection to
the very beginning of dw_pcie_host_init() and dw_pcie_ep_init(). Also
remove it from the dw_pcie_setup(), since it's more like a software
initialization step than hardware setup.
Link: https://lore.kernel.org/r/20210125044803.4310-1-Zhiqiang.Hou@nxp.com
Link: https://lore.kernel.org/linux-pci/20210407131255.702054-1-dmitry.baryshkov@linaro.org
Link: https://lore.kernel.org/r/20210413142219.2301430-1-dmitry.baryshkov@linaro.org
Fixes: 281f1f99cf ("PCI: dwc: Detect number of iATU windows")
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[DB: moved dw_pcie_iatu_detect to happen after host_init callback]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org # v5.11+
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
If the host which makes use of IP's integrated MSI Receiver losts
power during suspend, we need to reinit the RC and MSI Receiver in
resume. But after we move dw_pcie_msi_init() into the core, we have no
API to do so. Usually the dwc users need to call dw_pcie_setup_rc() to
reinit the RC, we can solve this problem by moving dw_pcie_msi_init()
to dw_pcie_setup_rc().
Link: https://lore.kernel.org/r/20210325152604.6e79deba@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The PCIe controller in Tegra194 SoC is not ECAM-compliant. With the
current hardware design, ECAM can be enabled only for one controller (the
C5 controller) with bus numbers starting from 160 instead of 0. A different
approach is taken to avoid this abnormal way of enabling ECAM for just one
controller but to enable configuration space access for all the other
controllers. In this approach, ops are added through MCFG quirk mechanism
which access the configuration spaces by dynamically programming iATU
(internal AddressTranslation Unit) to generate respective configuration
accesses just like the way it is done in DesignWare core sub-system.
This issue is specific to Tegra194 and it would be fixed in the future
generations of Tegra SoCs.
Link: https://lore.kernel.org/r/20210416134537.19474-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072700.15791-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
In config PCIE_TEGRA194_EP the mode incorrectly is referred to as
host mode. Fix it.
Link: https://lore.kernel.org/r/20201231032539.22322-1-wesley.sheng@amd.com
Signed-off-by: Wesley Sheng <wesley.sheng@amd.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Both TI's AM65x (K3) and TI's K2 PCIe driver are implemented in
pci-keystone. However Only K2 PCIe driver should use it's own pci_ops
for configuration space accesses. But commit 10a797c6e5
("PCI: dwc: keystone: Use pci_ops for config space accessors") used
custom pci_ops for both AM65x and K2. This breaks configuration space
access for AM65x platform. Fix it here.
Link: https://lore.kernel.org/r/20210317131518.11040-1-kishon@ti.com
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: <stable@vger.kernel.org> # v5.10
The only usage of them is to assign their address to the 'ops' field in
the pcie_port and the dw_pcie_ep structs, both which are pointers to
const. Make them const to allow the compiler to put them in read-only
memory.
Link: https://lore.kernel.org/r/20210207221604.48910-1-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
There are harmless warnings when compile testing the kernel with
CONFIG_TRIM_UNUSED_KSYMS:
drivers/pci/controller/dwc/pcie-al.o: no symbols
drivers/pci/controller/pci-thunder-ecam.o: no symbols
drivers/pci/controller/pci-thunder-pem.o: no symbols
The problem here is that the host drivers get built even when the
configuration symbols are all disabled, as they pretend to not be drivers
but are silently enabled because of the promise that ACPI-based systems
need no drivers.
Add back the normal symbols to have these drivers built, and change the
logic to otherwise only build them when both CONFIG_PCI_QUIRKS and
CONFIG_ACPI are enabled.
As a side-effect, this enables compile-testing the drivers on other
architectures, which in turn needs the acpi_get_rc_resources() function to
be defined.
Link: https://lore.kernel.org/r/20210308152501.2135937-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Compile-testing this driver without ECAM support results in a link failure:
ld.lld: error: undefined symbol: pci_ecam_map_bus
>>> referenced by pcie-al.c
>>> pci/controller/dwc/pcie-al.o:(al_pcie_map_bus) in archive drivers/built-in.a
Select CONFIG_ECAM like the other drivers do.
Link: https://lore.kernel.org/r/20210308152501.2135937-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
After updating pci-dra7xx driver to probe with ti-sysc and genpd, I
noticed that dra7xx_pcie_probe() would not run if a power-domains property
was configured for the interconnect target module.
Turns out that module_platform_driver_probe uses platform_driver_probe(),
while builtin_platform_driver uses platform_driver_register().
Only platform_driver_register() works for deferred probe as noted in the
comments for __platform_driver_probe() in drivers/base/platform.c with a
line saying "Note that this is incompatible with deferred probing".
With module_platform_driver_probe, we have platform_driver_probe() produce
-ENODEV error at device_initcall() level, and no further attempts are done.
Let's fix this by using module_platform_driver instead.
Note this is not an issue currently as we probe devices with simple-bus,
and only is needed as we start probing the device with ti-sysc, or when
probed with simple-pm-bus.
Note that we must now also remove __init for probe related functions to
avoid a section mismatch warning.
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Remove IRQ handler & data together for altera, brcmstb, dwc (Martin
Kaiser)
- Fix xgene race in installing chained IRQ handler (Martin Kaiser)
- Drop PCIE_RCAR config option (replaced by PCIE_RCAR_HOST) (Lad Prabhakar)
- Fix xgene comment about CRS vs CRS SV (Bjorn Helgaas)
* remotes/lorenzo/pci/misc:
PCI: hv: Fix typo
PCI: xgene: Fix CRS SV comment
PCI: brcmstb: Remove chained IRQ handler and data in one go
PCI: Drop PCIE_RCAR config option
PCI: xgene-msi: Fix race in installing chained irq handler
PCI: dwc: Remove IRQ handler and data in one go
PCI: altera-msi: Remove IRQ handler and data in one go
- Add support for SM8250 PCIe SF TBU clock (Dmitry Baryshkov)
- Use PHY_REFCLK_USE_PAD only for qcom ipq8064 (Ansuel Smith)
* pci/qcom:
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
The use of PHY_REFCLK_USE_PAD introduced a regression for apq8064 devices.
It was tested that while apq doesn't require the padding, ipq SoC must use
it or the kernel hangs on boot.
Link: https://lore.kernel.org/r/20201019165555.8269-1-ansuelsmth@gmail.com
Fixes: de3c4bf648 ("PCI: qcom: Add support for tx term offset for rev 2.1.0")
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.19+
We have removed the assumption that dw_pcie_ops always exists in the dwc
core driver, so we can remove the useless dw_pcie_ops now.
Link: https://lore.kernel.org/r/20210128144324.2fa8577c@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jonathan Chocron <jonnyc@amazon.com>
Some dwc-based device drivers, especially host-only drivers, may work well
with the default read_dbi/write_dbi/link_up implementations in
pcie-designware.c, so remove the assumption that every driver implements
them to simplify those drivers.
Link: https://lore.kernel.org/r/20210128144258.10329aa4@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The size parameter is unsigned long type which can accept size > 4GB. In
that case, the upper limit address must be programmed. Add support to
program the upper limit address and set INCREASE_REGION_SIZE in case size >
4GB.
Link: https://lore.kernel.org/r/1612250918-19610-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Since outbound iATU permits size to be greater than 4GB for which the
support is also available, allow EP function to send u64 size instead of
truncating to u32.
Link: https://lore.kernel.org/r/1609929900-19082-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Since commit a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and
"addr_space" resource setup into common code"), the code
setting dbi_base when the config space is defined in 'ranges' property
instead of 'reg' is dead code as dbi_base is never NULL.
Rather than fix this, let's just drop the code. Using ranges has been
deprecated since 2014. The only platforms using this were exynos5440,
i.MX6 and Spear13xx. Exynos5440 is dead and has been removed. i.MX6 and
Spear13xx had PCIe support added just before this was deprecated and
were fixed within a kernel release or 2.
Link: https://lore.kernel.org/r/20201215194149.86831-1-robh@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fw_devlink will defer the probe until all suppliers are ready. We can't
use builtin_platform_driver_probe() because it doesn't retry after probe
deferral. Convert it to builtin_platform_driver().
Link: https://lore.kernel.org/r/20210120105246.23218-1-michael@walle.cc
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The LX2160A rev2 uses the same PCIe IP as LS2088A, but LX2160A rev2 PCIe
controller is integrated with different stride between PFs' register
address.
Link: https://lore.kernel.org/r/20201026051448.1913-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DesignWare core has a TLP digest (TD) override bit in one of the control
registers of ATU. This bit also needs to be programmed for proper ECRC
functionality. This is currently identified as an issue with DesignWare
IP version 4.90a.
[bhelgaas: fix typos/grammar errors]
Link: https://lore.kernel.org/r/20201230165723.673-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115212435.19940-2-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.
Fix this by inverting the condition.
[bhelgaas: join string to make it greppable]
Fixes: 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.me
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:
In non-working case (next-20201211):
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)
In working case (v5.10-rc7):
0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)
The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.
Fixes: b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
- Support multiple ATU memory regions (Rob Herring)
- Warn if non-prefetchable memory aperture is > 32-bit (Vidya Sagar)
- Allow programming ATU for >4GB memory (Vidya Sagar)
- Move ATU offset out of driver match data (Rob Herring)
- Move "dbi", "dbi2", and "addr_space" resource setup to common code (Rob
Herring)
- Remove unneeded function wrappers (Rob Herring)
- Ensure all outbound ATU windows are reset to reduce dependencies on
bootloader (Rob Herring)
- Use the default MSI irq_chip for dra7xx (Rob Herring)
- Drop the .set_num_vectors() host op (Rob Herring)
- Move MSI interrupt setup into DWC common code (Rob Herring)
- Rework and simplify DWC MSI initialization (Rob Herring)
- Move link handling to DWC common code (Rob Herring)
- Move dw_pcie_msi_init() calls to DWC common code (Rob Herring)
- Move dw_pcie_setup_rc() calls to DWC common code (Rob Herring)
- Remove unnecessary wrappers around dw_pcie_host_init() (Rob Herring)
- Revert "keystone: Drop duplicated 'num-viewport'" to prepare for
detecting number of iATU regions without help from DT (Rob Herring)
- Move inbound and outbound windows to common struct (Rob Herring)
- Detect number of DWC iATU windows from device registers (Rob Herring)
- Drop samsung,exynos5440-pcie binding (Marek Szyprowski)
- Add samsung,exynos-pcie and samsung,exynos-pcie-phy bindings for
Exynos5433 variant (Marek Szyprowski)
- Rework phy-exynos-pcie driver to support Exynos5433 PCIe PHY (Jaehoon
Chung)
- Rework pci-exynos.c to support Exynos5433 PCIe host (Jaehoon Chung)
- Move tegra "dbi" accesses to post common DWC initialization (Vidya Sagar)
- Read tegra dbi" base address in application logic (Vidya Sagar)
- Fix tegra ASPM-L1SS advertisement disable code (Vidya Sagar)
- Set Tegra194 DesignWare IP version to 0x490A (Vidya Sagar)
- Continue tegra unconfig sequence even if parts fail (Vidya Sagar)
- Check return value of tegra_pcie_init_controller() (Vidya Sagar)
- Disable tegra LTSSM during L2 entry (Vidya Sagar)
- Add SM8250 SoC PCIe DT bindings and support (Manivannan Sadhasivam)
- Add SM8250 BDF to SID mapping (Manivannan Sadhasivam)
- Set 32-bit DMA mask for DWC MSI target address allocation (Vidya Sagar)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Set 32-bit DMA mask for MSI target address allocation
PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
PCI: qcom: Add SM8250 SoC support
dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC
PCI: tegra: Disable LTSSM during L2 entry
PCI: tegra: Check return value of tegra_pcie_init_controller()
PCI: tegra: Continue unconfig sequence even if parts fail
PCI: tegra: Set DesignWare IP version
PCI: tegra: Fix ASPM-L1SS advertisement disable code
PCI: tegra: Read "dbi" base address to program in application logic
PCI: tegra: Move "dbi" accesses to post common DWC initialization
PCI: dwc: exynos: Rework the driver to support Exynos5433 variant
phy: samsung: phy-exynos-pcie: rework driver to support Exynos5433 PCIe PHY
dt-bindings: phy: exynos: add the samsung,exynos-pcie-phy binding
dt-bindings: PCI: exynos: add the samsung,exynos-pcie binding
dt-bindings: PCI: exynos: drop samsung,exynos5440-pcie binding
PCI: dwc: Detect number of iATU windows
PCI: dwc: Move inbound and outbound windows to common struct
Revert "PCI: dwc/keystone: Drop duplicated 'num-viewport'"
PCI: dwc: Remove unnecessary wrappers around dw_pcie_host_init()
PCI: dwc: Move dw_pcie_setup_rc() to DWC common code
PCI: dwc: Move dw_pcie_msi_init() into core
PCI: dwc: Move link handling into common code
PCI: dwc: Rework MSI initialization
PCI: dwc: Move MSI interrupt setup into DWC common code
PCI: dwc: Drop the .set_num_vectors() host op
PCI: dwc/dra7xx: Use the common MSI irq_chip
PCI: dwc: Ensure all outbound ATU windows are reset
PCI: dwc/intel-gw: Remove some unneeded function wrappers
PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code
PCI: dwc/intel-gw: Move ATU offset out of driver match data
PCI: dwc: Add support to program ATU for >4GB memory
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Support multiple ATU memory regions
Add ECAM-related constants to provide a set of standard constants
defining memory address shift values to the byte-level address that can
be used to access the PCI Express Configuration Space, and then move
native PCI Express controller drivers to use the newly introduced
definitions retiring driver-specific ones.
Refactor pci_ecam_map_bus() function to use newly added constants so
that limits to the bus, device function and offset (now limited to 4K as
per the specification) are in place to prevent the defective or
malicious caller from supplying incorrect configuration offset and thus
targeting the wrong device when accessing extended configuration space.
This refactor also allows for the ".bus_shift" initialisers to be
dropped when the user is not using a custom value as a default value
will be used as per the PCI Express Specification.
Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>,
and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create()
issue with .bus_shift and to Vladimir for proposing the fix.
[bhelgaas: incorporate Vladimir's fix, update commit log]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Set DMA mask to 32-bit while allocating the MSI target address so that
the address is usable for both 32-bit and 64-bit MSI capable devices.
Throw a warning if it fails to set the mask to 32-bit to alert that
devices that are only 32-bit MSI capable may not work properly.
Link: https://lore.kernel.org/r/20201117165312.25847-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
For SM8250, we need to write the BDF to SID mapping in PCIe controller
register space for proper working. This is accomplished by extracting
the BDF and SID values from "iommu-map" property in DT and writing those
in the register address calculated from the hash value of BDF. In case
of collisions, the index of the next entry will also be written.
For the sake of it, let's introduce a "config_sid" callback and do it
conditionally for SM8250.
Link: https://lore.kernel.org/r/20201208121402.178011-4-mani@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The PCIe IP (rev 1.9.0) on SM8250 SoC is similar to the one used on
SDM845. Hence the support is added reusing the members of ops_2_7_0.
The key difference between ops_2_7_0 and ops_1_9_0 is the config_sid
callback, which will be added in successive commit.
Link: https://lore.kernel.org/r/20201208121402.178011-3-mani@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PCIe cards like Marvell SATA controller and some of the Samsung NVMe
drives don't support taking the link to L2 state. When the link doesn't
go to L2 state, Tegra194 requires the LTSSM to be disabled to allow PHY
to start the next link up process cleanly during suspend/resume sequence.
Failing to disable LTSSM results in the PCIe link not coming up in the
next resume cycle.
Link: https://lore.kernel.org/r/20201203133451.17716-6-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The return value of tegra_pcie_init_controller() must be checked before
PCIe link up check and registering debugfs entries subsequently as it
doesn't make sense to do these when the controller initialization itself
has failed.
Link: https://lore.kernel.org/r/20201203133451.17716-5-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Currently the driver checks for error value of different APIs during the
uninitialization sequence. It just returns from there if there is any error
observed for one of those calls. Comparatively it is better to continue the
uninitialization sequence irrespective of whether some of them are
returning error. That way, it is more closer to complete uninitialization.
Link: https://lore.kernel.org/r/20201203133451.17716-4-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Set the DesignWare IP version for Tegra194 to 0x490A. This would be used
by the DesigWare sub-system to do any version specific configuration
(Ex:- TD bit programming for ECRC).
Link: https://lore.kernel.org/r/20201203133451.17716-3-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
If the absence of CLKREQ# signal is indicated by the absence of
"supports-clkreq" in the device-tree node, current driver is disabling
the advertisement of ASPM-L1 Sub-States *before* the ASPM-L1 Sub-States
offset is correctly initialized. Since default value of the ASPM-L1SS
offset is zero, this is causing the Vendor-ID wrongly programmed to 0x10d2
instead of Nvidia's 0x10de thereby the quirks applicable for Tegra194 are
not being applied. This patch fixes this issue by refactoring the
code that disables the ASPM-L1SS advertisement.
Link: https://lore.kernel.org/r/20201203133451.17716-2-vidyas@nvidia.com
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe controller in Tegra194 requires the "dbi" region base address to be
programmed in one of the application logic registers to enable CPU access
to the "dbi" region. But, commit a0fd361db8 ("PCI: dwc: Move "dbi",
"dbi2", and "addr_space" resource setup into common code") moved the code
that reads the whereabouts of "dbi" region to the common code causing the
existing code in pcie-tegra194.c file to program NULL in the application
logic registers. This is causing null pointer dereference when the "dbi"
registers are accessed. This issue is fixed by explicitly reading the
"dbi" base address from DT node.
Link: https://lore.kernel.org/r/20201125192554.5401-1-vidyas@nvidia.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
commit a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space"
resource setup into common code") moved the code that sets up dbi_base
to DWC common code thereby creating a requirement to not access the "dbi"
region before calling common DWC initialization code. But, Tegra194
already had some code that programs some of the "dbi" registers resulting
in system crash. This patch addresses that issue by refactoring the code
to have accesses to the "dbi" region only after common DWC initialization.
Link: https://lore.kernel.org/r/20201125192234.2270-1-vidyas@nvidia.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Exynos5440 SoC support has been dropped since commit 8c83315da1 ("ARM:
dts: exynos: Remove Exynos5440"). Rework this driver to support DWC PCIe
variant found in the Exynos5433 SoCs.
The main difference in Exynos5433 variant is lack of the MSI support
(the MSI interrupt is not even routed to the CPU).
[mszyprow: reworked the driver to support only Exynos5433 variant,
simplified code, rebased onto current kernel code, added
regulator support, converted to the regular platform driver,
removed MSI related code, rewrote commit message, added help]
Link: https://lore.kernel.org/r/20201113170139.29956-6-m.szyprowski@samsung.com
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Currently the number of inbound and outbound iATU windows are determined
from DT properties. Unfortunately, there's 'num-viewport' for RC mode
and 'num-ib-windows' and 'num-ob-windows' for EP mode, yet the number of
windows is not mode dependent. Also, 'num-viewport' is not clear whether
that's inbound, outbound or both. We can probably assume it's outbound
windows as that's all RC mode uses.
However, using DT properties isn't really needed as the number of
regions can be detected at runtime by poking the iATU registers. The
basic algorithm is just writing a target address and reading back what
we wrote. In the unrolled ATU case, we have to take care not to go
past the mapped region.
With this, we can drop num_viewport in favor of num_ob_windows instead.
Link: https://lore.kernel.org/r/20201105211159.1814485-17-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The number of inbound and outbound windows are defined by the h/w and
apply to both RC and EP modes, so move them to the appropriate struct.
Link: https://lore.kernel.org/r/20201105211159.1814485-16-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 421063efaf.
In preparation to detect the number of iATU regions instead of using DT
properties, we need to keep reading 'num-viewport' for the Keystone
driver which doesn't use the iATU in older versions of the IP.
However, note that Keystone has been broken for some time with upstream
dts files which don't set 'num-viewports'. The reverted commit did
make the property optional, but now it's mandatory again.
Link: https://lore.kernel.org/r/20201105211159.1814485-15-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Many calls to dw_pcie_host_init() are in a wrapper function with
nothing else now. Let's remove the pointless extra layer.
Link: https://lore.kernel.org/r/20201105211159.1814485-14-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
All RC complex drivers must call dw_pcie_setup_rc(). The ordering of the
call shouldn't be too important other than being after any RC resets.
There's a few calls of dw_pcie_setup_rc() left as drivers implementing
suspend/resume need it.
Link: https://lore.kernel.org/r/20201105211159.1814485-13-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
All the DWC drivers do link setup and checks at roughly the same time.
Let's use the existing .start_link() hook (currently only used in EP
mode) and move the link handling to the core code.
The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device.
Link: https://lore.kernel.org/r/20201105211159.1814485-11-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
There are 3 possible MSI implementations for the DWC host. The first is
using the built-in DWC MSI controller. The 2nd is a custom MSI
controller as part of the PCI host (keystone only). The 3rd is an
external MSI controller (typically GICv3 ITS). Currently, the last 2
are distinguished with a .msi_host_init() hook with the 3rd option using
an empty function. However we can detect the 3rd case with the presence
of 'msi-parent' or 'msi-map' properties, so let's do that instead and
remove the empty functions.
Link: https://lore.kernel.org/r/20201105211159.1814485-10-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linuxppc-dev@lists.ozlabs.org
Platforms using the built-in DWC MSI controller all have a dedicated
interrupt with "msi" name or at index 0, so let's move setting up the
interrupt to the common DWC code.
spear13xx and dra7xx are the 2 oddballs with muxed interrupts, so
we need to prevent configuring the MSI interrupt by setting msi_irq
to negative.
Link: https://lore.kernel.org/r/20201105211159.1814485-9-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
There's no reason for the .set_num_vectors() host op. Drivers needing a
non-default value can just initialize pcie_port.num_vectors directly.
Link: https://lore.kernel.org/r/20201105211159.1814485-8-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The dra7xx MSI irq_chip implementation is identical to the default DWC one.
The only difference is the interrupt handler as the MSI interrupt is muxed
with other interrupts, but that doesn't affect the irq_chip part of it.
Link: https://lore.kernel.org/r/20201105211159.1814485-7-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-omap@vger.kernel.org
The Layerscape driver clears the ATU registers which may have been
configured by the bootloader. Any driver could have the same issue
and doing it for all drivers doesn't hurt, so let's move it into the
common DWC code.
Link: https://lore.kernel.org/r/20201105211159.1814485-6-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linuxppc-dev@lists.ozlabs.org
Remove some of the pointless levels of functions that just wrap or group
a series of other functions.
Link: https://lore.kernel.org/r/20201105211159.1814485-5-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Most DWC drivers use the common register resource names "dbi", "dbi2", and
"addr_space", so let's move their setup into the DWC common code.
This means 'dbi_base' in particular is setup later, but it looks like no
drivers touch DBI registers before dw_pcie_host_init or dw_pcie_ep_init.
Link: https://lore.kernel.org/r/20201105211159.1814485-4-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
The ATU offset should be a register range in DT called 'atu', not driver
match data. Any future platforms with a different ATU offset should add
it to their DT.
This is also in preparation to do DBI resource setup in the core DWC
code, so let's move setting atu_base later in intel_pcie_rc_setup().
Link: https://lore.kernel.org/r/20201105211159.1814485-3-robh@kernel.org
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Currently the Keystone driver can only be compile-tested on ARM, but
this restriction seems unnecessary. Get rid of it to increase test
coverage.
Build-tested with allyesconfig on x86, ppc, mips and riscv.
Link: https://lore.kernel.org/r/20200906195128.279342-1-alex.dewar90@gmail.com
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Add support to program the ATU to enable translations for >4GB sizes of
the prefetchable memory apertures.
Link: https://lore.kernel.org/r/20201118144626.32189-3-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo <jingoohan1@gmail.com>
The current ATU setup only supports a single memory resource which
isn't sufficient if there are also prefetchable memory regions. In order
to support multiple memory regions, we need to move away from fixed ATU
slots and rework the assignment. As there's always an ATU entry for
config space, let's assign index 0 to config space. Then we assign
memory resources to index 1 and up. Finally, if we have an I/O region
and slots remaining, we assign the I/O region last. If there aren't
remaining slots, we keep the same config and I/O space sharing.
Link: https://lore.kernel.org/r/20201026181652.418729-1-robh@kernel.org
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Prior to commit 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources"),
the DWC driver was setting up the last memory resource rather than the
first memory resource. This doesn't matter for most platforms which only
have 1 memory resource, but it broke Tegra194 which has a 2nd
(prefetchable) memory region that requires an ATU entry. The first region
on Tegra194 relies on the default 1:1 pass-thru of outbound transactions
and doesn't need an ATU entry.
Fixes: 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/r/20201026154852.221483-1-robh@kernel.org
Reported-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
- Drop return value checking for debugfs_create() calls (Greg
Kroah-Hartman)
- Convert debugfs "ports" file to use DEFINE_SEQ_ATTRIBUTE() (Liu Shixin)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Convert to use DEFINE_SEQ_ATTRIBUTE macro
PCI: tegra: No need to check return value of debugfs_create() functions
- Make sure PCIe is reset before init to work around QSDK U-Boot issue
(Ansuel Smith)
- Set iproc affinity mask on MSI interrupts (Mark Tomlinson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Make sure PCIe is reset before init for rev 2.1.0
- Return -EPROBE_DEFER in case the gpio isn't ready (Bean Huo)
* remotes/lorenzo/pci/kirin:
PCI: kirin: Return -EPROBE_DEFER in case the gpio isn't ready
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva)
- Drop redundant error messages after devm_clk_get() (Anson Huang)
* remotes/lorenzo/pci/imx6:
PCI: imx6: Do not output error message when devm_clk_get() failed with -EPROBE_DEFER
PCI: imx6: Use fallthrough pseudo-keyword
NXP Layerscape (ls1028a, ls2088a), dra7xxx and imx6 platforms are either
programmed or statically configured to forward the error triggered by a
link-down state (eg no connected endpoint device) on the system bus for
PCI configuration transactions; these errors are reported as an SError
at system level, which is fatal.
Enumerating a PCI tree when the PCIe link is down is not sensible
either, so even if the link-up check is racy (link can go down after
map_bus() is called) add a link-up check in map_bus() to prevent issuing
configuration transactions when the link is down.
SError report:
SError Interrupt on CPU2, code 0xbf000002 -- SError
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
pstate: 20000085 (nzCv daIf -PAN -UAO BTYPE=--)
pc : pci_generic_config_read+0x3c/0xe0
lr : pci_generic_config_read+0x24/0xe0
sp : ffff80001003b7b0
x29: ffff80001003b7b0 x28: ffff80001003ba74
x27: ffff000971d96800 x26: ffff00096e77e0a8
x25: ffff80001003b874 x24: ffff80001003b924
x23: 0000000000000004 x22: 0000000000000000
x21: 0000000000000000 x20: ffff80001003b874
x19: 0000000000000004 x18: ffffffffffffffff
x17: 00000000000000c0 x16: fffffe0025981840
x15: ffffb94c75b69948 x14: 62203a383634203a
x13: 666e6f635f726568 x12: 202c31203d207265
x11: 626d756e3e2d7375 x10: 656877202c307830
x9 : 203d206e66766564 x8 : 0000000000000908
x7 : 0000000000000908 x6 : ffff800010900000
x5 : ffff00096e77e080 x4 : 0000000000000000
x3 : 0000000000000003 x2 : 84fa3440ff7e7000
x1 : 0000000000000000 x0 : ffff800010034000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x1c0
show_stack+0x18/0x28
dump_stack+0xd8/0x134
panic+0x180/0x398
add_taint+0x0/0xb0
arm64_serror_panic+0x78/0x88
do_serror+0x68/0x180
el1_error+0x84/0x100
pci_generic_config_read+0x3c/0xe0
dw_pcie_rd_other_conf+0x78/0x110
pci_bus_read_config_dword+0x88/0xe8
pci_bus_generic_read_dev_vendor_id+0x30/0x1b0
pci_bus_read_dev_vendor_id+0x4c/0x78
pci_scan_single_device+0x80/0x100
Link: https://lore.kernel.org/r/20200916054130.8685-1-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log, remove Fixes tag]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Currently, dw_pcie_msi_init() allocates and maps page for msi, then
program the PCIE_MSI_ADDR_LO and PCIE_MSI_ADDR_HI. The Root Complex
may lose power during suspend-to-RAM, so when we resume, we want to
redo the latter but not the former. If designware based driver (for
example, pcie-tegra194.c) calls dw_pcie_msi_init() in resume path, the
msi page will be leaked.
As pointed out by Rob and Ard, there's no need to allocate a page for
the MSI address, we could use an address in the driver data.
To avoid map the MSI msg again during resume, we move the map MSI msg
from dw_pcie_msi_init() to dw_pcie_host_init().
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201009155505.5a580ef5@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
If MSI is disabled, there's no need to program PCIE_MSI_INTR0_MASK
and PCIE_MSI_INTR0_ENABLE registers.
Link: https://lore.kernel.org/r/20201009155436.27e67238@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
After applying "PCI: dwc: Add common iATU register support",
there is no need to set own iATU in the Keystone driver itself.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-5-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This gets iATU register area from reg property that has reg-names "atu".
In Synopsys DWC version 4.80 or later, since iATU register area is
separated from core register area, this area is necessary to get from
DT independently.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Enable pci-meson to build as a module whenever ARCH_MESON is enabled.
Link: https://lore.kernel.org/r/20200918181251.32423-1-khilman@baylibre.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Yue Wang <yue.wang@amlogic.com>
PCI host bridge driver can be probed before the gpiochip it requires,
so, of_get_named_gpio() can return -EPROBE_DEFER. Current code lets the
kirin_pcie_probe() directly return -ENODEV, which results in the PCI
host controller driver probe failure; with this error code the PCI host
controller driver will not be probed again when the gpiochip driver is
loaded.
Fix the above issue by letting kirin_pcie_probe() return -EPROBE_DEFER in
such a case.
Link: https://lore.kernel.org/r/20200918123800.19983-1-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIe EP mode support for ls1088a and ls2088a, there are some
difference between LS1 and LS2 platform, so refactor the code of
the EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-10-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
dw_pcie_ep_raise_msix_irq was never called in the exisitng driver
before, because the ls1046a platform don't support the MSIX feature
and msix_capable was always set to false.
Now that add the ls1088a platform with MSIX support, use the doorbell
method to support the MSIX feature.
Link: https://lore.kernel.org/r/20200918080024.13639-9-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The different PCIe controller in one board may be have different
capability of MSI or MSIX, so change the way of getting the MSI
capability, make it more flexible.
Link: https://lore.kernel.org/r/20200918080024.13639-8-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Fix some format issue of the code in EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-7-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Each PF of EP device should have its own MSI or MSIX capabitily
struct, so create a dw_pcie_ep_func struct and move the msi_cap
and msix_cap to this struct from dw_pcie_ep, and manage the PFs
via a list.
Link: https://lore.kernel.org/r/20200918080024.13639-5-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move the function of getting MSI capability to the front of init
function, because the init function of the EP platform driver will use
the return value by the function of getting MSI capability.
Link: https://lore.kernel.org/r/20200918080024.13639-4-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add the doorbell mode of MSI-X in DWC EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-3-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add multiple PFs support for DWC, due to different PF have different
config space, we use func_conf_select callback function to access
the different PF's config space, the different chip company need to
implement this callback function when use the DWC IP core and intend
to support multiple PFs feature.
Link: https://lore.kernel.org/r/20200918080024.13639-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Bjorn Helgaas