As recently reported, some platforms provide a list of power
resources for device power state D3hot, through the _PR3 object,
but they do not provide a list of power resources for device power
state D0.
Among other things, this causes acpi_device_get_power() to return
D3hot as the current state of the device in question if all of the
D3hot power resources are "on", because it sees the power_resources
flag set and calls acpi_power_get_inferred_state() which finds that
D3hot is the shallowest power state with all of the associated power
resources turned "on", so that's what it returns. Moreover, that
value takes precedence over the acpi_dev_pm_explicit_get() return
value, because it means a deeper power state. The device may very
well be in D0 physically at that point, however.
Moreover, the presence of _PR3 without _PR0 for a given device
means that only one D3-level power state can be supported by it.
Namely, because there are no power resources to turn "off" when
transitioning the device from D0 into D3cold (which should be
supported since _PR3 is present), the evaluation of _PS3 should
be sufficient to put it straight into D3cold, but this means that
the effect of turning "on" the _PR3 power resources is unclear,
so it is better to avoid doing that altogether. Consequently,
there is no practical way do distinguish D3cold from D3hot for
the device in question and the power states of it can be labeled
so that D3hot is the deepest supported one (and Linux assumes
that putting a device into D3hot via ACPI may cause power to be
removed from it anyway, for legacy reasons).
To work around the problem described above modify the ACPI
enumeration of devices so that power resources are only used
for device power management if the list of D0 power resources
is not empty and make it mart D3cold as supported only if that
is the case and the D3hot list of power resources is not empty
too.
Fixes: ef85bdbec4 ("ACPI / scan: Consolidate extraction of power resources lists")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205057
Link: https://lore.kernel.org/linux-acpi/20200603194659.185757-1-hdegoede@redhat.com/
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: youling257@gmail.com
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The SPCR and STAO table needs to be released after
using it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When commit 68bdb67732 ("ACPI: add support for ACPI reconfiguration
notifiers") introduced reconfiguration notifiers, it missed the point
that the ACPI table, which might be loaded and then unloaded via
ConfigFS, could contain devices that were not enumerated by their
parents.
In such cases, the stale platform device is dangling in the system
while the rest of the devices from the same table are already gone.
Introduce acpi_platform_device_remove_notify() notifier that, in
similar way to I²C or SPI buses, unregisters the platform devices
on table removal event.
Fixes: 68bdb67732 ("ACPI: add support for ACPI reconfiguration notifiers")
Depends-on: 00500147cb ("drivers: Introduce device lookup variants by ACPI_COMPANION device")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ rjw: Changelog & function rename ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Let's document why the lock is not needed in acpi_scan_init(), right now
this is not really obvious.
[akpm@linux-foundation.org: fix tpyo]
Link: http://lkml.kernel.org/r/20190731135306.31524-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said they
should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here, due
to some changes to the kobject core code. Those too have all been acked
by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHDbw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynDAgCfbb4LBR6I50wFXb8JM/R6cAS7qrsAn1unshKV
8XCYcif2RxjtdJWXbjdm
=/rLh
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core/kobject updates from Greg KH:
"Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said
they should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here,
due to some changes to the kobject core code. Those too have all been
acked by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
kobject: clean up the kobject add documentation a bit more
kobject: Fix kernel-doc comment first line
kobject: Remove docstring reference to kset
firmware_loader: Fix a typo ("syfs" -> "sysfs")
kobject: fix dereference before null check on kobj
Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
init/config: Do not select BUILD_BIN2C for IKCONFIG
Provide in-kernel headers to make extending kernel easier
kobject: Improve doc clarity kobject_init_and_add()
kobject: Improve docs for kobject_add/del
driver core: platform: Fix the usage of platform device name(pdev->name)
livepatch: Replace klp_ktype_patch's default_attrs with groups
cpufreq: schedutil: Replace default_attrs field with groups
padata: Replace padata_attr_type default_attrs field with groups
irqdesc: Replace irq_kobj_type's default_attrs field with groups
net-sysfs: Replace ktype default_attrs field with groups
block: Replace all ktype default_attrs with groups
samples/kobject: Replace foo_ktype's default_attrs field with groups
kobject: Add support for default attribute groups to kobj_type
driver core: Postpone DMA tear-down until after devres release for probe failure
...
ACPICA commit 92ec0935f27e217dff0b176fca02c2ec3d782bb5
ACPI_COMPARE_NAME changed to ACPI_COMPARE_NAMESEG
This clarifies (1) this is a compare on 4-byte namesegs, not
a generic compare. Improves understanding of the code.
Link: https://github.com/acpica/acpica/commit/92ec0935
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Parsing entries in an ACPI table had assumed a generic header
structure. There is no standard ACPI header, though, so less common
layouts with different field sizes required custom parsers to go through
their subtable entry list.
Create the infrastructure for adding different table types so parsing
the entries array may be more reused for all ACPI system tables and
the common code doesn't need to be duplicated.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subsequent code treats button_device_ids[] entries differently, and
it's hard to follow without a hint as to which is which.
Add comments to identify the power button, lid, and sleep button
devices.
The "PNP" prefix is owned by Microsoft, so they distribute the
canonical list of "PNP" IDs.
Link: https://uefi.org/PNP_ACPI_Registry
Link: https://download.microsoft.com/download/1/6/1/161ba512-40e2-4cc9-843a-923143f3456c/devids.txt
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_bus_extract_wakeup_device_power_package() is a static function
with a single caller that supplies (device->handle, &device->wakeup).
Simplify the interface so the caller need only supply "device".
This makes it obvious that "wakeup", i.e., &device->wakeup, can never
be NULL, so remove the unnecessary check for that.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix some misspellings in comments. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Point of View TAB-P1006W-232-3G tablet has an ACPI firmware node with
a HID of BSG2150 describing the 2 Bosch sensors used in the device a
BMC150 compatible accelerometer and a BMC150 compatible magnetometer.
The ACPI firmware node actually contains 3 I2cSerialBusV2 resources,
but this seems to be a copy and paste job from the BSG1160 firmware node
on other devices, since there is no i2c-client listening to the 0x68
address listed in the third resource and the 0x68 address is identical
to the address of the third resource in the BSG1160 nodes, where as the
other 2 addresses are different.
Add the ID to the I2C multi instantiate list, so that the
i2c-multi-instantiate.c driver can handle it;
And add the necessary info to the i2c-multi-instantiate.c driver to
enumerate all I2C slaves correctly.
To avoid triggering the:
if (i < multi->num_clients) {
dev_err(dev, "Error finding driver, idx %d\n", i);
Error this commit lists the 3th device in the i2c_inst_data with a
type of "bsg2150_dummy_dev".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for architectures
that have devices that perform DMA that is not cache coherent. Based
on the existing arm64 implementation and also used for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel data
leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script.
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlwctQgLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYMxgQ//dBpAfS4/J76CdAbYry2zqgcOUU9hIrD6NHiEMWov
ltJxyvEl3LsUmIdEj3aCrYL9jZN0qsnCzn5BVj2c3jDIVgD64fAr7HDf/PbEEfKb
j6/GgEnVLPZV+sQMvhNA5jOzHrkseaqPa4/pNLFZ/l8jnuZ2d+btusDWJpMoVDer
TXVwtIfgeIu0gTygYOShLYXd5qptWKWsZEpbTZOO2sE6+x+ZJX7yQYUxYDTlcOIj
JWVO2l5QNHPc5T9o2at+6L5aNUvnZOxT79sWgyZLn0Kc+FagKAVwfLqUEl0v7foG
8k/xca5/8p3afB1DfrIrtplJqis7cVgdyGxriwuuoO8X4F0nPyWwpGmxsBhrWwwl
xTqC4UorEJ7QwoP6Azopk/vYI2QXIUBLjuCJCuFXZj9+2BGf4IfvBY1S2cLM9qLs
HMcxQonuXJii044KEFS96ePEuiT+igVINweIFBKWcgNCEG0UQtyL6RQ1U5297ipF
JiWZAqD+p9X52UdKS+oKfAiZEekMXn6Xyo97+YCiNpfOo0GP5eEcwhL+JpY4AiRq
apPXtsRy2o1s8yfjdraUIM2Mc2n62vFKb35oUbGCd/QO9piPrFQHl6T0HHcHk4YR
XrUXcHieFZBCYqh7ZVa4RL8Msq1wvGuTL4Dxl43mXdsMoUFRR6eSNWLoAV4IpOLZ
WgA=
=in72
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
"A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for
architectures that have devices that perform DMA that is not cache
coherent. Based on the existing arm64 implementation and also used
for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel
data leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script"
* tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping: (73 commits)
dma-mapping: fix inverted logic in dma_supported
dma-mapping: deprecate dma_zalloc_coherent
dma-mapping: zero memory returned from dma_alloc_*
sparc/iommu: fix ->map_sg return value
sparc/io-unit: fix ->map_sg return value
arm64: default to the direct mapping in get_arch_dma_ops
PCI: Remove unused attr variable in pci_dma_configure
ia64: only select ARCH_HAS_DMA_COHERENT_TO_PFN if swiotlb is enabled
dma-mapping: bypass indirect calls for dma-direct
vmd: use the proper dma_* APIs instead of direct methods calls
dma-direct: merge swiotlb_dma_ops into the dma_direct code
dma-direct: use dma_direct_map_page to implement dma_direct_map_sg
dma-direct: improve addressability error reporting
swiotlb: remove dma_mark_clean
swiotlb: remove SWIOTLB_MAP_ERROR
ACPI / scan: Refactor _CCA enforcement
dma-mapping: factor out dummy DMA ops
dma-mapping: always build the direct mapping code
dma-mapping: move dma_cache_sync out of line
dma-mapping: move various slow path functions out of line
...
Rather than checking the DMA attribute at each callsite, just pass it
through for acpi_dma_configure() to handle directly. That can then deal
with the relatively exceptional DEV_DMA_NOT_SUPPORTED case by explicitly
installing dummy DMA ops instead of just skipping setup entirely. This
will then free up the dev->dma_ops == NULL case for some valuable
fastpath optimisations.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Tony Luck <tony.luck@intel.com>
The ACPI device with INT3515 _HID is representing a complex USB PD
hardware infrastructure which includes several I2C slave ICs.
We add an ID to the I2C multi instantiate list to enumerate
all I2C slaves correctly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix ACPICA issues related to the handling of module-level AML
and make the ACPI initialization code parse ECDT before loading
the definition block tables (Erik Schmauss).
- Update ACPICA to upstream revision 20181003 including fixes
related to the ill-defined "generic serial bus" and the handling
of the _REG object (Bob Moore).
- Fix some issues with system-wide suspend/resume on Intel BYT/CHT
related to the handling of I2C controllers in the ACPI LPSS driver
for Intel SoCs (Hans de Goede).
- Modify the ACPI namespace scanning code to enumerate INT33FE HID
devices as platform devices with I2C resources to avoid device
enumeration problems on boards with Dollar Cove or Whiskey Cove
Intel PMICs (Hans de Goede).
- Prevent ACPICA from using ktime_get() during early resume from
system-wide suspend before resuming the timekeeping which generally
is unsafe and triggers a warning from the timekeeping code (Bart
Van Assche).
- Add low-level real time clock support to the ACPI Time and Aalarm
Device (TAD) driver (Rafael Wysocki).
- Fix the ACPI SBS driver to avoid GPE storms on MacBook Pro and
Oopses when removing modules (Ronald Tschalär).
- Fix the ACPI PPTT parsing code to handle architecturally unknown
cache types properly (Jeffrey Hugo).
- Fix initialization issue in the ACPI processor driver (Dou Liyang).
- Clean up the code in several places (Andy Shevchenko, Bartlomiej
Zolnierkiewicz, David Arcari, zhong jiang).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=arbR
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These fix ACPICA issues related to the handling of module-level AML,
fix an ordering issue during ACPI initialization, update ACPICA to
upstream revision 20181003 (including fixes mostly), fix issues with
system-wide suspend/resume related to the ACPI driver for Intel SoCs
(LPSS), fix device enumeration issues on boards with Dollar Cove or
Whiskey Cove Intel PMICs, prevent ACPICA from calling ktime_get() in
unsuitable conditions, update a few drivers and clean up some code in
several places.
Specifics:
- Fix ACPICA issues related to the handling of module-level AML and
make the ACPI initialization code parse ECDT before loading the
definition block tables (Erik Schmauss).
- Update ACPICA to upstream revision 20181003 including fixes related
to the ill-defined "generic serial bus" and the handling of the
_REG object (Bob Moore).
- Fix some issues with system-wide suspend/resume on Intel BYT/CHT
related to the handling of I2C controllers in the ACPI LPSS driver
for Intel SoCs (Hans de Goede).
- Modify the ACPI namespace scanning code to enumerate INT33FE HID
devices as platform devices with I2C resources to avoid device
enumeration problems on boards with Dollar Cove or Whiskey Cove
Intel PMICs (Hans de Goede).
- Prevent ACPICA from using ktime_get() during early resume from
system-wide suspend before resuming the timekeeping which generally
is unsafe and triggers a warning from the timekeeping code (Bart
Van Assche).
- Add low-level real time clock support to the ACPI Time and Aalarm
Device (TAD) driver (Rafael Wysocki).
- Fix the ACPI SBS driver to avoid GPE storms on MacBook Pro and
Oopses when removing modules (Ronald Tschalär).
- Fix the ACPI PPTT parsing code to handle architecturally unknown
cache types properly (Jeffrey Hugo).
- Fix initialization issue in the ACPI processor driver (Dou Liyang).
- Clean up the code in several places (Andy Shevchenko, Bartlomiej
Zolnierkiewicz, David Arcari, zhong jiang)"
* tag 'acpi-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (33 commits)
ACPI / scan: Create platform device for INT33FE ACPI nodes
ACPI / OSL: Use 'jiffies' as the time bassis for acpi_os_get_timer()
ACPI: probe ECDT before loading AML tables regardless of module-level code flag
ACPICA: Remove acpi_gbl_group_module_level_code and only use acpi_gbl_execute_tables_as_methods instead
ACPICA: AML Parser: fix parse loop to correctly skip erroneous extended opcodes
ACPICA: AML interpreter: add region addresses in global list during initialization
ACPI: TAD: Add low-level support for real time capability
ACPI: remove redundant 'default n' from Kconfig
ACPI / SBS: Fix rare oops when removing modules
ACPI / SBS: Fix GPE storm on recent MacBookPro's
ACPI/PPTT: Handle architecturally unknown cache types
drivers: base: cacheinfo: Do not populate sysfs for unknown cache types
ACPICA: Update version to 20181003
ACPICA: Never run _REG on system_memory and system_IO
ACPICA: Split large interpreter file
ACPICA: Update for field unit access
ACPICA: Rename some of the Field Attribute defines
ACPICA: Update for generic_serial_bus and attrib_raw_process_bytes protocol
ACPI / processor: Fix the return value of acpi_processor_ids_walk()
ACPI / LPSS: Resume BYT/CHT I2C controllers from resume_noirq
...
Bay and Cherry Trail devices with a Dollar Cove or Whiskey Cove PMIC
have an ACPI node with a HID of INT33FE which is a "virtual" battery
device implementing a standard ACPI battery interface which depends upon
a proprietary, undocument OpRegion called BMOP. Since we do have docs
for the actual fuel-gauges used on these boards we instead use native
fuel-gauge drivers talking directly to the fuel-gauge ICs on boards which
rely on this INT33FE device for their battery monitoring.
On boards with a Dollar Cove PMIC the INT33FE device's resources (_CRS)
describe a non-existing I2C client at address 0x6b with a bus-speed of
100KHz. This is a problem on some boards since there are actual devices
on that same bus which need a speed of 400KHz to function properly.
This commit adds the INT33FE HID to the list of devices with I2C resources
which should be enumerated as a platform-device rather then letting the
i2c-core instantiate an i2c-client matching the first I2C resource,
so that its bus-speed will not influence the max speed of the I2C bus.
This fixes e.g. the touchscreen not working on the Teclast X98 II Plus.
The INT33FE device on boards with a Whiskey Cove PMIC is somewhat special.
Its first I2C resource is for a secondary I2C address of the PMIC itself,
which is already described in an ACPI device with an INT34D3 HID.
But it has 3 more I2C resources describing 3 other chips for which we do
need to instantiate I2C clients and which need device-connections added
between them for things to work properly. This special case is handled by
the drivers/platform/x86/intel_cht_int33fe.c code.
Before this commit that code was binding to the i2c-client instantiated
for the secondary I2C address of the PMIC, since we now instantiate a
platform device for the INT33FE device instead, this commit also changes
the intel_cht_int33fe driver from an i2c driver to a platform driver.
This also brings the intel_cht_int33fe drv inline with how we instantiate
multiple i2c clients from a single ACPI device in other cases, as done
by the drivers/platform/x86/i2c-multi-instantiate.c code.
Reported-and-tested-by: Alexander Meiler <alex.meiler@protonmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This goes through a lot of hooks just to call arch_teardown_dma_ops.
Replace it with a direct call instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Some devices have multiple I2cSerialBus resources and for things to work
an i2c-client must be instantiated for each, each with its own
i2c_device_id.
Normally we only instantiate an i2c-client for the first resource, using
the ACPI HID as id.
This commit adds a list of HIDs of devices, which need multiple i2c-clients
instantiated from a single fwnode, to acpi_device_enumeration_by_parent and
makes acpi_device_enumeration_by_parent return false for these devices so
that a platform device will be instantiated.
This allows the drivers/platform/x86/i2c-multi-instantiate.c driver, which
knows which i2c_device_id to use for each resource, to bind to the fwnode
and initiate an i2c-client for each resource.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit 63347db0af "ACPI / scan: Use acpi_bus_get_status() to
initialize ACPI_TYPE_DEVICE devs" the status field of normal acpi_devices
gets set to 0 by acpi_bus_type_and_status() and filled with its actual
value later when acpi_add_single_object() calls acpi_bus_get_status().
This means that any acpi_match_device_ids() calls in between will always
fail with -ENOENT.
We already have a workaround for this, which temporary forces status to
ACPI_STA_DEFAULT in drivers/acpi/x86/utils.c: acpi_device_always_present()
and the next commit in this series adds another acpi_match_device_ids()
call between status being initialized as 0 and the acpi_bus_get_status()
call.
Rather then adding another workaround, this commit makes
acpi_bus_type_and_status() initialize status to ACPI_STA_DEFAULT, this is
safe to do as the only code looking at status between the initialization
and the acpi_bus_get_status() call is those acpi_match_device_ids() calls.
Note this does mean that we need to (re)set status to 0 in case the
acpi_bus_get_status() call fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Array indirect_io_hosts[] is declared in acpi_is_indirect_io_slave() as a
const array, which means that the array will be re-built for each call.
Optimise by adding the static attribute, which means that the array is
added to const-data pool and not re-built per function call.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
At least on one Dell system the PNP motherboard resources device
includes resources used by WDAT table. Since PNP gets initialized before
WDAT it results following error and no watchdog:
platform wdat_wdt: failed to claim resource 3: [io 0x046a-0x046c]
ACPI: watchdog: Device creation failed: -16
Now, the PNP system driver is already accustomed with the situation that
it cannot reserve all those motherboard resources because drivers using
those might have reserved them already. In addition putting WDAT table
resources under motherboard resources device makes sense in general.
Fix this by initializing WDAT right before PNP. This allows WDAT to
reserve all its resources and still keeps PNP system driver happy.
Reported-by: Shubhrata.Priyadarsh@dell.com
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
Through the logical PIO framework, systems which otherwise have no IO space
access to legacy ISA/LPC devices may access these devices through so-called
"indirect IO" method. In this, IO space accesses for non-PCI hosts are
redirected to a host LLDD to manually generate the IO space (bus) accesses.
Hosts are able to register a region in logical PIO space to map to its bus
address range.
Indirect IO child devices have an associated host-specific bus address.
Special translation is required to map between a logical PIO address for a
device and its host bus address.
Since in the ACPI tables the child device IO resources would be the
host-specific values, it is required the ACPI scan code should not
enumerate these devices, and that this should be the responsibility of the
host driver so that it can "fixup" the resources so that they map to the
appropriate logical PIO addresses.
To avoid enumerating these child devices, add a check from
acpi_device_enumeration_by_parent() as to whether the parent for a device
is a member of a known list of "indirect IO" hosts. For now, the HiSilicon
LPC host controller ID is added.
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the ACPI scan has special handling for serial bus slaves, in that
it makes it the responsibility of the slave device's parent to enumerate
the device.
To support other types of slave devices which require the same special
handling but where the bus is not strictly a serial bus, such as devices on
the HiSilicon LPC controller bus, rename acpi_is_serial_bus_slave() to
acpi_device_enumeration_by_parent(), so that the name can fit the wider
purpose.
Also rename the associated device flag acpi_device_flags.serial_bus_slave
to .enumeration_by_parent.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In current design of ACPI container offline, Kernel emits
KOBJ_CHANGE uevent to user space to indidate that the ejection of
the container was triggered by platform. (caa73ea15 patch)
A pure KOBJ_CHANGE uevent is not enough for user space to identify
the purpose. For example, a "udevadm trigger" command can also
be used to emit change event to all udev rules. A udev rule can not
identify that the event is from kernel for offline or from udevadm
for other purpose. Then the offline action in udev rule may also be
triggered by udevadm tool.
So, similar to the change uevent of dock, kernel sends the
KOBJ_CHANGE uevent with a offline environmental data to indicate
purpose. It's useful by udev rule for using ENV{EVENT} filter.
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_get_bus_status wrapper for acpi_bus_get_status_handle has some
code to handle certain device quirks, in some cases we also need this
quirk handling for the initial _STA call.
Specifically on some devices calling _STA before all _DEP dependencies
are met results in errors like these:
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[GenericSerialBus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region GenericSerialBus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
acpi_get_bus_status already has code to avoid this, so by using it we
also silence these errors from the initial _STA call.
Note that in order for the acpi_get_bus_status handling for this to work,
we initialize dep_unmet to 1 until acpi_device_dep_initialize gets called,
this means that battery devices will be instantiated with an initial
status of 0. This is not a problem, acpi_bus_attach will get called soon
after the instantiation anyways and it will update the status as first
point of order.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On platforms (ASUS X550ZE and possibly all ASUS X series) with valid ECDT
EC but invalid DSDT EC, EC PM ops won't be invoked as ECDT EC is not an
ACPI device. Thus the following commit actually removed post-resume
acpi_ec_enable_event() invocation for such platforms, and triggered a
regression on them that after being resumed, EC (actually should be ECDT)
driver stops handling EC events:
Commit: c2b46d679b
Subject: ACPI / EC: Add PM operations to improve event handling for resume process
Notice that the root cause actually is "ECDT is not an ACPI device" rather
than "the timing of acpi_ec_enable_event() invocation", this patch fixes
this issue by enumerating ECDT EC as an ACPI device. Due to the existence
of the noirq stage, the ability of tuning the timing of
acpi_ec_enable_event() invocation is still meaningful.
This patch is a little bit different from the posted fix by moving
acpi_config_boot_ec() from acpi_ec_ecdt_start() to acpi_ec_add() to make
sure that EC event handling won't be stopped as long as the ACPI EC driver
is bound. Thus the following sequence shouldn't disable EC event handling:
unbind,suspend,resume,bind.
Fixes: c2b46d679b (ACPI / EC: Add PM operations to improve event handling for resume process)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196847
Reported-by: Luya Tshimbalanga <luya@fedoraproject.org>
Tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat a
bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnD+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynAmgCfSSr/9qiCE0vfP5eVYjddzxfWyZ4AoMbKORZC
5x2KVW0Btrbs3WmnD7ZU
=PSea
-----END PGP SIGNATURE-----
Merge tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver pull request for 4.15-rc1.
Lots of serial driver updates in here, some small vt cleanups, and a
raft of SPDX and license boilerplate cleanups, messing up the diffstat
a bit.
Nothing major, with no realy functional changes except better hardware
support for some platforms.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (110 commits)
tty: ehv_bytechan: fix spelling mistake
tty: serial: meson: allow baud-rates lower than 9600
serial: 8250_fintek: Fix crash with baud rate B0
serial: 8250_fintek: Disable delays for ports != 0
serial: 8250_fintek: Return -EINVAL on invalid configuration
tty: Remove redundant license text
tty: serdev: Remove redundant license text
tty: hvc: Remove redundant license text
tty: serial: Remove redundant license text
tty: add SPDX identifiers to all remaining files in drivers/tty/
tty: serial: jsm: remove redundant pointer ts
tty: serial: jsm: add space before the open parenthesis '('
tty: serial: jsm: fix coding style
tty: serial: jsm: delete space between function name and '('
tty: serial: jsm: add blank line after declarations
tty: serial: jsm: change the type of local variable
tty: serial: imx: remove dead code imx_dma_rxint
tty: serial: imx: disable ageing timer interrupt if dma in use
serial: 8250: fix potential deadlock in rs485-mode
serial: m32r_sio: Drop redundant .data assignment
...
UART devices is expected to be enumerated by SerDev subsystem.
During ACPI scan, serial devices behind SPI, I2C or UART buses are not
enumerated, allowing them to be enumerated by their respective parents.
Rename *spi_i2c_slave* to *serial_bus_slave* as this will be used for serial
devices on serial buses (SPI, I2C or UART).
On Macs an empty ResourceTemplate is returned for uart slaves.
Instead the device properties "baud", "parity", "dataBits", "stopBits" are
provided. Add a check for "baud" in acpi_is_serial_bus_slave().
Signed-off-by: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Tested-by: Peter Y. Chuang <peteryuchuang@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add functionality to read LPIT table, which provides:
- Sysfs interface to read residency counters via
/sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
/sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
Here the count "low_power_idle_cpu_residency_us" shows the time spent
by CPU package in low power state. This is read via MSR interface,
which points to MSR for PKG C10.
Here the count "low_power_idle_system_residency_us" show the count the
system was in low power state. This is read via MMIO interface. This
is mapped to SLP_S0 residency on modern Intel systems. This residency
is achieved only when CPU is in PKG C10 and all functional blocks are
in low power state.
It is possible that none of the above counters present or anyone of the
counter present or all counters present.
For example: On my Kabylake system both of the above counters present.
After suspend to idle these counts updated and prints:
6916179
6998564
This counter can be read by tools like turbostat to display. Or it can
be used to debug, if modern systems are reaching desired low power state.
- Provides an interface to read residency counter memory address
This address can be used to get the base address of PMC memory
mapped IO. This is utilized by intel_pmc_core driver to print
more debug information.
In addition, to avoid code duplication to read iomem, removed the read of
iomem from acpi_os_read_memory() in osl.c and made a common function
acpi_os_read_iomem(). This new function is used for reading iomem in
in both osl.c and acpi_lpit.c.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Introduce fwnode operations for all of the separate types of
"firmware nodes" that can be handled by the device properties
framework and drop the type field from struct fwnode_handle
(Sakari Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references
to the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework
to the new UUID API (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0rnk
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework, make the framework use const fwnode arguments all over, add
a helper for the consolidated handling of node references and switch
over the framework to the new UUID API.
Specifics:
- Introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework and drop the type field from struct fwnode_handle (Sakari
Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references to
the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework to the
new UUID API (Andy Shevchenko)"
* tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: device property: Switch to use new generic UUID API
device property: export irqchip_fwnode_ops
device property: Introduce fwnode_property_get_reference_args
device property: Constify fwnode property API
device property: Constify argument to pset fwnode backend
ACPI: Constify internal fwnode arguments
ACPI: Constify acpi_bus helper functions, switch to macros
ACPI: Prepare for constifying acpi_get_next_subnode() fwnode argument
device property: Get rid of struct fwnode_handle type field
ACPI: Use IS_ERR_OR_NULL() instead of non-NULL check in is_acpi_data_node()
* acpi-ec:
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
* acpi-dma:
ACPI/IORT: Add IORT named component memory address limits
ACPI: Make acpi_dma_configure() DMA regions aware
ACPI: Introduce DMA ranges parsing
ACPI: Make acpi_dev_get_resources() method agnostic
* acpi-processor:
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI: processor: use dev_dbg() instead of dev_warn() when CPPC probe failed
* acpi-cppc:
mailbox: pcc: Drop uninformative output during boot
On some systems the platform firmware expects GPEs to be enabled
before the enumeration of devices and if that expectation is not
met, the systems in question may not boot in some situations.
For this reason, change the initialization ordering of the ACPI
subsystem to make it enable GPEs before scanning the namespace
for the first time in order to enumerate devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 2a5708409e (ACPI / EC: Fix a gap that ECDT EC cannot handle
EC events) introduced acpi_ec_ecdt_start(), but that function is
invoked before acpi_ec_query_init(), which is too early. This causes
the kernel to crash if an EC event occurs after boot, when ec_query_wq
is not valid:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000102
...
Workqueue: events acpi_ec_event_handler
task: ffff9f539790dac0 task.stack: ffffb437c0e10000
RIP: 0010:__queue_work+0x32/0x430
Normally, the DSDT EC should always be valid, so acpi_ec_ecdt_start()
is actually a no-op in the majority of cases. However, commit
c712bb58d8 (ACPI / EC: Add support to skip boot stage DSDT probe)
caused the probing of the DSDT EC as the "boot EC" to be skipped when
the ECDT EC is valid and uncovered the bug.
Fix this issue by invoking acpi_ec_ecdt_start() after acpi_ec_query_init()
in acpi_ec_init().
Link: https://jira01.devtools.intel.com/browse/LCK-4348
Fixes: 2a5708409e (ACPI / EC: Fix a gap that ECDT EC cannot handle EC events)
Fixes: c712bb58d8 (ACPI / EC: Add support to skip boot stage DSDT probe)
Reported-by: Wang Wendy <wendy.wang@intel.com>
Tested-by: Feng Chenzhou <chenzhoux.feng@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Current ACPI DMA configuration set-up device DMA capabilities through
kernel defaults that do not take into account platform specific DMA
configurations reported by firmware.
By leveraging the ACPI acpi_dev_get_dma_resources() API, add code
in acpi_dma_configure() to retrieve the DMA regions to correctly
set-up PCI devices DMA parameters.
Rework the ACPI IORT kernel API to make sure they can accommodate
the DMA set-up required by firmware. By making PCI devices DMA set-up
ACPI IORT specific, the kernel is shielded from unwanted regressions
that could be triggered by parsing DMA resources on arches that were
previously ignoring them (ie x86/ia64), leaving kernel behaviour
unchanged on those arches.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices have limited addressing capabilities and cannot
reference the whole memory address space while carrying out DMA
operations (eg some devices with bus address bits range smaller than
system bus - which prevents them from using bus addresses that are
otherwise valid for the system).
The ACPI _DMA object allows bus devices to define the DMA window that is
actually addressable by devices that sit upstream the bus, therefore
providing a means to parse and initialize the devices DMA masks and
addressable DMA range size.
By relying on the generic ACPI kernel layer to retrieve and parse
resources, introduce ACPI core code to parse the _DMA object.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SPI and I2C slaves are enumerated by their respective parents rather
than the ACPI core. They are recognized by presence of _CRS resources,
which however are missing on Macs. Check for presence of device
properties instead.
Reported-and-tested-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of relying on the struct fwnode_handle type field, define
fwnode_operations structs for all separate types of fwnodes. To find out
the type, compare to the ops field to relevant ops structs.
This change has two benefits:
1. it avoids adding the type field to each and every instance of struct
fwnode_handle, thus saving memory and
2. makes the ops field the single factor that defines both the types of
the fwnode as well as defines the implementation of its operations,
decreasing the possibility of bugs when developing code dealing with
fwnode internals.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rearrange the core device properties code by moving the code
specific to each supported platform configuration framework
(ACPI, DT and build-in) into a separate file (Sakari Ailus).
- Add helper functions for accessing device properties in a
firmware-agnostic way (Sakari Ailus, Kieran Bingham).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EcrF
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These mostly rearrange the device properties core code and add a few
helper functions to it as a foundation for future work.
Specifics:
- Rearrange the core device properties code by moving the code
specific to each supported platform configuration framework (ACPI,
DT and build-in) into a separate file (Sakari Ailus).
- Add helper functions for accessing device properties in a
firmware-agnostic way (Sakari Ailus, Kieran Bingham)"
* tag 'devprop-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Add fwnode_graph_get_port_parent
device property: Add FW type agnostic fwnode_graph_get_remote_node
device property: Introduce fwnode_device_is_available()
device property: Move fwnode graph ops to firmware specific locations
device property: Move FW type specific functionality to FW specific files
ACPI: Constify argument to acpi_device_is_present()
In hotplug logic, it always indicates non-specific failure to
platform through _OST when handing ACPI hot-remove event failed. Then
platform terminates the hot-remove process but it can not identify
the reason.
Base on current hot-remove code, there have two situations that it
returns busy:
- OSPM try to offline an individual device, but the device offline
function returns "busy".
- When the ejection event is applied to an "not offlined yet"
container. OSPM sends a kobject change event to userspace and
returns "busy".
Both of them will returns -EBUSY to ACPI device hotplug function.
Then, the hotplug function indicates non-specific failure to platform
just like for any other error, e.g. -ENODEV or -EIO.
The benefit to the platform for identifying the OS "busy" state is
that it can use a different approach to handle the "busy" instead of
simply terminating the hot-remove operation for an unknown reason.
For example, the platform can wait for a while and then re-trigger
hot-remove.
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[ rjw: Changelog massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pm:
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems
platform: x86: intel-hid: Wake up the system from suspend-to-idle
platform: x86: intel-vbtn: Wake up the system from suspend-to-idle
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle
platform/x86: Add driver for ACPI INT0002 Virtual GPIO device
PCI / PM: Restore PME Enable if skipping wakeup setup
PM / sleep: Print timing information if debug is enabled
ACPI / PM: Clean up device wakeup enable/disable code
ACPI / PM: Change log level of wakeup-related message
USB / PCI / PM: Allow the PCI core to do the resume cleanup
ACPI / PM: Run wakeup notify handlers synchronously
Conflicts:
drivers/base/power/main.c
The run_wake flag in struct acpi_device_wakeup_flags stores the
information on whether or not the device can generate wakeup
signals at run time, but in ACPI that really is equivalent to
being able to generate wakeup signals at all.
In fact, run_wake will always be set after successful executeion of
acpi_setup_gpe_for_wake(), but if that fails, the device will not be
able to use a wakeup GPE at all, so it won't be able to wake up the
systems from sleep states too. Hence, run_wake actually means that
the device is capable of triggering wakeup and so it is equivalent
to the valid flag.
For this reason, drop run_wake from struct acpi_device_wakeup_flags
and make sure that the valid flag is only set if
acpi_setup_gpe_for_wake() has been successful.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The device and fwnode property API supports Devicetree, ACPI and pset
properties. The implementation of this functionality for each firmware
type was embedded in the fwnode property core. Move it out to firmware
type specific locations, making it easier to maintain.
Depends-on: ("of: Move OF property and graph API from base.c to property.c")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This will be needed in constifying the fwnode API.
The side effects the function had have been moved to the callers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit f406270bf7 ("ACPI / scan: Set the visited flag for all
enumerated devices") caused that two group of special SPI or I2C
devices do not enumerate. SPI and I2C devices are expected to be
enumerated by the SPI and I2C subsystems but change caused that
acpi_bus_attach() marks those devices with acpi_device_set_enumerated().
First group of devices are matched using Device Tree compatible property
with special _HID "PRP0001". Those devices have matched scan handler,
acpi_scan_attach_handler() retuns 1 and acpi_bus_attach() marks them
with acpi_device_set_enumerated().
Second group of devices without valid _HID such as "LNXVIDEO" have
device->pnp.type.platform_id set to zero and change again marks them
with acpi_device_set_enumerated().
Fix this by flagging the SPI and I2C devices during struct acpi_device
object initialization time and let the code in acpi_bus_attach() to go
through the device_attach() and acpi_default_enumeration() path for all
SPI and I2C devices.
Fixes: f406270bf7 (ACPI / scan: Set the visited flag for all enumerated devices)
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While deferring the probe of IOMMU masters, xlate and
add_device callbacks called from iort_iommu_configure
can pass back error values like -ENODEV, which means
the IOMMU cannot be connected with that master for real
reasons. Before the IOMMU probe deferral, all such errors
were ignored. Now all those errors are propagated back,
killing the master's probe for such errors. Instead ignore
all the errors except EPROBE_DEFER, which is the only one
of concern and let the master work without IOMMU, thus
restoring the old behavior. Also make explicit that
acpi_dma_configure handles only -EPROBE_DEFER from
iort_iommu_configure.
Fixes: 5a1bb638d5 ("drivers: acpi: Handle IOMMU lookup failure with deferred probing or error")
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This includes:
* Some code optimizations for the Intel VT-d driver
* Code to switch off a previously enabled Intel IOMMU
* Support for 'struct iommu_device' for OMAP, Rockchip and
Mediatek IOMMUs
* Some header optimizations for IOMMU core code headers and a
few fixes that became necessary in other parts of the kernel
because of that
* ACPI/IORT updates and fixes
* Some Exynos IOMMU optimizations
* Code updates for the IOMMU dma-api code to bring it closer to
use per-cpu iova caches
* New command-line option to set default domain type allocated
by the iommu core code
* Another command line option to allow the Intel IOMMU switched
off in a tboot environment
* ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using
an IDENTITY domain in conjunction with DMA ops, Support for
SMR masking, Support for 16-bit ASIDs (was previously broken)
* Various other small fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3aE8
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
This is an equivalent to the DT's handling of the iommu master's probe
with deferred probing when the corrsponding iommu is not probed yet.
The lack of a registered IOMMU can be caused by the lack of a driver for
the IOMMU, the IOMMU device probe not having been performed yet, having
been deferred, or having failed.
The first case occurs when the firmware describes the bus master and
IOMMU topology correctly but no device driver exists for the IOMMU yet
or the device driver has not been compiled in. Return NULL, the caller
will configure the device without an IOMMU.
The second and third cases are handled by deferring the probe of the bus
master device which will eventually get reprobed after the IOMMU.
The last case is currently handled by deferring the probe of the bus
master device as well. A mechanism to either configure the bus master
device without an IOMMU or to fail the bus master device probe depending
on whether the IOMMU is optional or mandatory would be a good
enhancement.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
[Lorenzo: Added fixes for dma_coherent_mask overflow, acpi_dma_configure
called multiple times for same device]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
acpi_bus_attach() does not check the visited flag for devices that
have been enumerated already and some of them may be enumerated
for multiple times as a result, because some callers of
acpi_bus_scan() don't check the visited flag either.
For this reason, modify acpi_bus_attach() to check the visited flag
and avoid enumerating devices that have already been enumerated.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Joey Lee <jlee@suse.com>
The current code in acpi_bus_attach() is inconsistent with respect
to device objects with ACPI drivers bound to them, as it allows
ACPI drivers to bind to device objects with existing "physical"
device companions, but it doesn't allow "physical" device objects
to be created for ACPI device objects with ACPI drivers bound to
them. Thus, in some cases, the outcome depends on the ordering
of events which is confusing at best.
For this reason, modify acpi_bus_attach() to call
acpi_default_enumeration() for device objects with the
pnp.type.platform_id flag set regardless of whether or not
any ACPI drivers are bound to them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Joey Lee <jlee@suse.com>
Commit 10c7e20b2f (ACPI / scan: fix enumeration (visited) flags for
bus rescans) attempted to fix a problem with ACPI-based enumerateion
of I2C/SPI devices, but it forgot to ensure that the visited flag
will be set for all of the other enumerated devices, so fix that.
Fixes: 10c7e20b2f (ACPI / scan: fix enumeration (visited) flags for bus rescans)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194885
Reported-and-tested-by: Kevin Locke <kevin@kevinlocke.name>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
/sys/firmware/acpi/hotplug/force_remove was presumably added to support
auto offlining in the past. This is, however, inherently dangerous for
some hotplugable resources like memory. The memory offlining fails when
the memory is still in use and cannot be dropped or migrated. If we
ignore the failure we are basically allowing for subtle memory
corruption or a crash.
We have actually noticed the later while hitting BUG() during the memory
hotremove (remove_memory):
ret = walk_memory_range(PFN_DOWN(start), PFN_UP(start + size - 1), NULL,
check_memblock_offlined_cb);
if (ret)
BUG();
it took us quite non-trivial time realize that the customer had
force_remove enabled. Even if the BUG was removed here and we could
propagate the error up the call chain it wouldn't help at all because
then we would hit a crash or a memory corruption later and harder to
debug. So force_remove is unfixable for the memory hotremove. We haven't
checked other hotplugable resources to be prone to a similar problems.
Remove the force_remove functionality because it is not fixable currently.
Keep the sysfs file and report an error if somebody tries to enable it.
Encourage users to report about the missing functionality and work with
them with an alternative solution.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes, the users may require a quirk to be provided from ACPI subsystem
core to prevent a GPE from flooding.
Normally, if a GPE cannot be dispatched, ACPICA core automatically prevents
the GPE from firing. But there are cases the GPE is dispatched by _Lxx/_Exx
provided via AML table, and OSPM is lacking of the knowledge to get
_Lxx/_Exx correctly executed to handle the GPE, thus the GPE flooding may
still occur.
The existing quirk mechanism can be enabled/disabled using the following
commands to prevent such kind of GPE flooding during runtime:
# echo mask > /sys/firmware/acpi/interrupts/gpe00
# echo unmask > /sys/firmware/acpi/interrupts/gpe00
To avoid GPE flooding during boot, we need a boot stage mechanism.
This patch provides such a boot stage quirk mechanism to stop this kind of
GPE flooding. This patch doesn't fix any feature gap but since the new
feature gaps could be found in the future endlessly, and can disappear if
the feature gaps are filled, providing a boot parameter rather than a DMI
table should suffice.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=53071
Link: https://bugzilla.kernel.org/show_bug.cgi?id=117481
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/887793
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng).
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=55TG
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Here are new versions of two ACPICA changes that were deferred
previously due to a problem they had introduced, two cleanups on top
of them and the removal of a useless warning message from the ACPI
core.
Specifics:
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng)
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui)"
* tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
ACPI: do not warn if _BQC does not exist
The introduction of acpi_dma_configure() allows to configure DMA
and related IOMMU for any device that is DMA capable. To achieve
that goal it ensures DMA masks are set-up to sane default values
before proceeding with IOMMU and DMA ops configuration.
On x86/ia64 systems, through acpi_bind_one(), acpi_dma_configure() is
called for every device that has an ACPI companion, in that every device
is considered DMA capable on x86/ia64 systems (ie acpi_get_dma_attr() API),
which has the side effect of initializing dma masks also for
pseudo-devices (eg CPUs and memory nodes) and potentially for devices
whose dma masks were not set-up before the acpi_dma_configure() API was
introduced, which may have noxious side effects.
Therefore, in preparation for IORT firmware specific DMA masks set-up,
wrap the default DMA masks set-up in acpi_dma_configure() inside an IORT
specific wrapper that reverts to a NOP on x86/ia64 systems, restoring the
default expected behaviour on x86/ia64 systems and keeping DMA default
masks set-up on IORT based (ie ARM) arch configurations.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Starting from ACPI spec 3.0, it's only clarified that _BCM control
method is required if _BCL is implemented. There is no word
saying _BQC is required.
And in ACPI spec 6.1 B.5.4, for _BQC, it is explicitly stated that
"This optional method returns the current brightness level of a
built-in display output device. If present, it must be set by
the platform for initial brightness."
Thus remove the obsolete warning message.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
DT based systems have a generic kernel API to configure IOMMUs
for devices (ie of_iommu_configure()).
On ARM based ACPI systems, the of_iommu_configure() equivalent can
be implemented atop ACPI IORT kernel API, with the corresponding
functions to map device identifiers to IOMMUs and retrieve the
corresponding IOMMU operations necessary for DMA operations set-up.
By relying on the iommu_fwspec generic kernel infrastructure,
implement the IORT based IOMMU configuration for ARM ACPI systems
and hook it up in the ACPI kernel layer that implements DMA
configuration for a device.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [ACPI core]
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On DT based systems, the of_dma_configure() API implements DMA
configuration for a given device. On ACPI systems an API equivalent to
of_dma_configure() is missing which implies that it is currently not
possible to set-up DMA operations for devices through the ACPI generic
kernel layer.
This patch fills the gap by introducing acpi_dma_configure/deconfigure()
calls that for now are just wrappers around arch_setup_dma_ops() and
arch_teardown_dma_ops() and also updates ACPI and PCI core code to use
the newly introduced acpi_dma_configure/acpi_dma_deconfigure functions.
Since acpi_dma_configure() is used to configure DMA operations, the
function initializes the dma/coherent_dma masks to sane default values
if the current masks are uninitialized (also to keep the default values
consistent with DT systems) to make sure the device has a complete
default DMA set-up.
The DMA range size passed to arch_setup_dma_ops() is sized according
to the device coherent_dma_mask (starting at address 0x0), mirroring the
DT probing path behaviour when a dma-ranges property is not provided
for the device being probed; this changes the current arch_setup_dma_ops()
call parameters in the ACPI probing case, but since arch_setup_dma_ops()
is a NOP on all architectures but ARM/ARM64 this patch does not change
the current kernel behaviour on them.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [pci]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We have a couple of drivers, acpi_apd.c and acpi_lpss.c,
that need to pass extra build-in properties to the devices
they create. Previously the drivers added those properties
to the struct device which is member of the struct
acpi_device, but that does not work. Those properties need
to be assigned to the struct device of the platform device
instead in order for them to become available to the
drivers.
To fix this, this patch changes acpi_create_platform_device
function to take struct property_entry pointer as parameter.
Fixes: 20a875e2e8 (serial: 8250_dw: Add quirk for APM X-Gene SoC)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Yazen Ghannam <yazen.ghannam@amd.com>
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
Starting from Intel Skylake the iTCO watchdog timer registers were moved to
reside in the same register space with SMBus host controller. Not all
needed registers are available though and we need to unhide P2SB (Primary
to Sideband) device briefly to be able to read status of required NO_REBOOT
bit. The i2c-i801.c SMBus driver used to handle this and creation of the
iTCO watchdog platform device.
Windows, on the other hand, does not use the iTCO watchdog hardware
directly even if it is available. Instead it relies on ACPI Watchdog Action
Table (WDAT) table to describe the watchdog hardware to the OS. This table
contains necessary information about the the hardware and also set of
actions which are executed by a driver as needed.
This patch implements a new watchdog driver that takes advantage of the
ACPI WDAT table. We split the functionality into two parts: first part
enumerates the WDAT table and if found, populates resources and creates
platform device for the actual driver. The second part is the driver
itself.
The reason for the split is that this way we can make the driver itself to
be a module and loaded automatically if the WDAT table is found. Otherwise
the module is not loaded.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible to register _Qxx from namespace and use the ECDT EC to
perform event handling. The reported bug reveals that Windows is using ECDT
in this way in case the namespace EC is not present. This patch facilitates
Linux to support ECDT in this way.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=115021
Reported-and-tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Tested-by: Jonh Henderson <jw.hendy@gmail.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit e647b53227 ("ACPI: Add early device probing infrastructure")
introduced code that allows inserting driver specific
struct acpi_probe_entry probe entries into ACPI linker sections
(one per-subsystem, eg irqchip, clocksource) that are then walked
to retrieve the data and function hooks required to probe the
respective kernel components.
Probing for all entries in a section is triggered through
the __acpi_probe_device_table() function, that in turn, according
to the table ID a given probe entry reports parses the table
with the function retrieved from the respective section structures
(ie struct acpi_probe_entry). Owing to the current ACPI table
parsing implementation, the __acpi_probe_device_table() function
has to share global variables with the acpi_match_madt() function, so
in order to guarantee mutual exclusion locking is required
between the two functions.
Current kernel code implements the locking through the acpi_probe_lock
spinlock; this has the side effect of requiring all code called
within the lock (ie struct acpi_probe_entry.probe_{table/subtbl} hooks)
not to sleep.
However, kernel subsystems that make use of the early probing
infrastructure are relying on kernel APIs that may sleep (eg
irq_domain_alloc_fwnode(), among others) in the function calls
pointed at by struct acpi_probe_entry.{probe_table/subtbl} entries
(eg gic_v2_acpi_init()), which is a bug.
Since __acpi_probe_device_table() is called from context
that is allowed to sleep the acpi_probe_lock spinlock can be replaced
with a mutex; this fixes the issue whilst still guaranteeing
mutual exclusion.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fixes: e647b53227 (ACPI: Add early device probing infrastructure)
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXmLlrAAoJEFxbo/MsZsTRvRQH/1wOMF8BmlbZfR7H3qwDfjst
ApNifCiZE08xDtWBlwUaBFAQxyflQS9BBiNZDVK0sysIdXeOdpWV7V0ZjRoLL+xr
czsaaGXDcmXxJxApoMDVuT7FeP6rEk6LVAYRoHpVjJjMZGW3BbX1vZaMW4DXl2WM
9YNaF2Lj+rpc1f8iG31nUxwkpmcXFog6ct4tu7HiyCFT3hDkHt/a4ghuBdQItCkd
vqBa1pTpcGtQBhSmWzlylN/PV2+NKcRd+kGiwd09/O/rNzogTMCTTWeHKAtMpPYb
Cu6oSqJtlK5o0vtr0qyLSWEGIoyjE2gE92s0wN3iCzFY1PldqdsxUO622nIj+6o=
=G6q3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.8-rc0:
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places"
* tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (47 commits)
xen: add static initialization of steal_clock op to xen_time_ops
xen/pvhvm: run xen_vcpu_setup() for the boot CPU
xen/evtchn: use xen_vcpu_id mapping
xen/events: fifo: use xen_vcpu_id mapping
xen/events: use xen_vcpu_id mapping in events_base
x86/xen: use xen_vcpu_id mapping when pointing vcpu_info to shared_info
x86/xen: use xen_vcpu_id mapping for HYPERVISOR_vcpu_op
xen: introduce xen_vcpu_id mapping
x86/acpi: store ACPI ids from MADT for future usage
x86/xen: update cpuid.h from Xen-4.7
xen/evtchn: add IOCTL_EVTCHN_RESTRICT
xen-blkback: really don't leak mode property
xen-blkback: constify instance of "struct attribute_group"
xen-blkfront: prefer xenbus_scanf() over xenbus_gather()
xen-blkback: prefer xenbus_scanf() over xenbus_gather()
xen: support runqueue steal time on xen
arm/xen: add support for vm_assist hypercall
xen: update xen headers
xen-pciback: drop superfluous variables
xen-pciback: short-circuit read path used for merging write values
...
Add support for ACPI reconfiguration notifiers to allow subsystems
to react to changes in the ACPI tables that happen after the initial
enumeration. This is similar with the way dynamic device tree
notifications work.
The reconfigure notifications supported for now are device add and
device remove.
Since ACPICA allows only one table notification handler, this patch
makes the table notifier function generic and moves it out of the
sysfs specific code.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the ACPI tables change as a result of a dinamically loaded table
and a bus rescan is required the enumeration/visited flag are not
consistent.
I2C/SPI are not directly enumerated in acpi_bus_attach(), however
the visited flag is set. This makes it impossible to check if an
ACPI device has already been enumerated by the I2C and SPI
subsystems. To fix this issue we only set the visited flags if
the device is not I2C or SPI.
With this change we also need to remove setting visited to false
from acpi_bus_attach(), otherwise if we rescan already enumerated
I2C/SPI devices we try to re-enumerate them.
Note that I2C/SPI devices can be enumerated either via a scan handler
(when using PRP0001) or via regular device_attach(). In either case
the flow goes through acpi_default_enumeration() which makes it the
ideal place to mark the ACPI device as enumerated.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI 6.0 introduces a new table STAO to list the devices which are used
by Xen and can't be used by Dom0. On Xen virtual platforms, the physical
UART is used by Xen. So here it hides UART from Dom0.
CC: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
CC: Len Brown <lenb@kernel.org> (supporter:ACPI)
CC: linux-acpi@vger.kernel.org (open list:ACPI)
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On ARM64 some devices use the AMBA device and not the platform bus for
probing so add support for this. Uses a dummy clock for apb_pclk as ACPI
does not have a suitable clock representation and to keep the core
AMBA bus code unchanged between probing methods.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There's an idiom in use by 7 Linux drivers to detect the presence of a
particular ACPI HID by walking the namespace with acpi_get_devices().
The callback passed to acpi_get_devices() is mostly identical across
the drivers, leading to lots of duplicate code.
Add acpi_dev_present(), the ACPI equivalent to pci_dev_present(),
allowing us to deduplicate all that boilerplate in the drivers.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_device_add() allocates and adds an element to acpi_bus_id_list
(or increments the instance count if the device's HID is already
present in the list), but the element is never deleted from the list
nor freed. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some ACPI node's _STA will touch operation region field, since the
evaluation of _STA in acpi_bus_type_and_status is very early, the
operation region handler is not ready yet. Instead of fail that function
and not creating the acpi_device node consequently, set status to 0 so
that later when the driver for that device is probing, it can find
the acpi_device node and proceed normally. And at that time, the
handler for the operation region is ready and its _STA evaluation will
succeed, its present status can be checked there.
Even there will be no driver using this node later, it doesn't seem
hurt to have one more acpi_device node created with status set to 0.
This happens on Microsoft Surface 3, where the SPI device node NTRG's
_STA touches GPIO fields and the SPI core driver will only enumerate SPI
devices from ACPI if the acpi_device node is 1: created; 2: _STA
indicates it's present.
Note that due to another problem in SPI driver, for NTRG to be actually
enumerated, some changes have to be made in the SPI layer, which is
addressed by Mika(not send out yet):
https://bugzilla.kernel.org/show_bug.cgi?id=104291#c23
Link: https://bugzilla.kernel.org/show_bug.cgi?id=104291
Reported-by: Bastien Nocera <bugzilla@hadess.net>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adding acpi_get_dma_attr() to query DMA attributes of ACPI devices.
It returns the enum dev_dma_attr, which communicates DMA information
more clearly. This API replaces the acpi_check_dma(), which will be
removed in subsequent patch.
This patch also provides a convenient function, acpi_dma_supported(),
to check DMA support of the specified ACPI device.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
IRQ controllers and timers are the two types of device the kernel
requires before being able to use the device driver model.
ACPI so far lacks a proper probing infrastructure similar to the one
we have with DT, where we're able to declare IRQ chips and
clocksources inside the driver code, and let the core code pick it up
and call us back on a match. This leads to all kind of really ugly
hacks all over the arm64 code and even in the ACPI layer.
In order to allow some basic probing based on the ACPI tables,
introduce "struct acpi_probe_entry" which contains just enough
data and callbacks to match a table, an optional subtable, and
call a probe function. A driver can, at build time, register itself
and expect being called if the right entry exists in the ACPI
table.
A acpi_probe_device_table() is provided, taking an identifier for
a set of acpi_prove_entries, and iterating over the registered
entries.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Empirically, acpi_add_id is mostly called with string literals, so
using kstrdup_const for initializing struct acpi_hardware_id::id saves
a little run-time memory and a string copy.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is preparation for using kstrdup_const to initialize that member.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make device_get_next_child_node() work with ACPI data-only subnodes
introduced previously.
Namely, replace acpi_get_next_child() with acpi_get_next_subnode()
that can handle (and return) child device objects as well as child
data-only subnodes of the given device and modify the ACPI part
of the GPIO subsystem to handle data-only subnodes returned by it.
To that end, introduce acpi_node_get_gpiod() taking a struct
fwnode_handle pointer as the first argument. That argument may
point to an ACPI device object as well as to a data-only subnode
and the function should do the right thing (ie. look for the matching
GPIO descriptor correctly) in either case.
Next, modify fwnode_get_named_gpiod() to use acpi_node_get_gpiod()
instead of acpi_get_gpiod_by_index() which automatically causes
devm_get_gpiod_from_child() to work with ACPI data-only subnodes
that may be returned by device_get_next_child_node() which in turn
is required by the users of that function (the gpio_keys_polled
and gpio-leds drivers).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/acpi/scan.c
The conflict is resolved by moving the just introduced
acpi_device_is_first_physical_node() to bus.c and using
the existing acpi_companion_match() from there.
There will be an additional commit to combine the two.
Some devices, like MFD subdevices, share a single ACPI companion device so
that they are able to access their resources and children. However,
currently all these subdevices are attached to the ACPI power domain and
this might cause that the power methods for the companion device get called
more than once.
In order to solve this we attach the ACPI power domain only to the first
physical device that is bound to the ACPI companion device. In case of MFD
devices, this is the parent MFD device itself.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move the registration of the ACPI bus type to acpi_bus_init() and
avoid using ACPI going forward if it fails (too many things depend on
the presence of the ACPI bus type).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To reduce the size of scan.c and improve the readability of it, move
code related to device notification, the definitions of the ACPI bus
operations and the driver management code to drivers/acpi/bus.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To reduce the size of scan.c and improve the readability of it, move
code related device matching into drivers/acpi/bus.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To reduce the size of scan.c and improve the readability of it, move
all code related to device sysfs, modalias creation etc. to a new
file called device_sysfs.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Device drivers typically use ACPI _HIDs/_CIDs listed in struct device_driver
acpi_match_table to match devices. However, for generic drivers, we do not
want to list _HID for all supported devices. Also, certain classes of devices
do not have _CID (e.g. SATA, USB). Instead, we can leverage ACPI _CLS,
which specifies PCI-defined class code (i.e. base-class, subclass and
programming interface). This patch adds support for matching ACPI devices using
the _CLS method.
To support loadable module, current design uses _HID or _CID to match device's
modalias. With the new way of matching with _CLS this would requires modification
to the current ACPI modalias key to include _CLS. This patch appends PCI-defined
class-code to the existing ACPI modalias as following.
acpi:<HID>:<CID1>:<CID2>:..:<CIDn>:<bbsspp>:
E.g:
# cat /sys/devices/platform/AMDI0600:00/modalias
acpi:AMDI0600:010601:
where bb is th base-class code, ss is te sub-class code, and pp is the
programming interface code
Since there would not be _HID/_CID in the ACPI matching table of the driver,
this patch adds a field to acpi_device_id to specify the matching _CLS.
static const struct acpi_device_id ahci_acpi_match[] = {
{ ACPI_DEVICE_CLASS(PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff) },
{},
};
In this case, the corresponded entry in modules.alias file would be:
alias acpi*:010601:* ahci_platform
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-video: (38 commits)
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
dell-laptop: Port to new backlight interface selection API
compal-laptop: Port to new backlight interface selection API
asus-wmi: Port to new backlight interface selection API
asus-laptop: Port to new backlight interface selection API
apple-gmux: Port to new backlight interface selection API
acer-wmi: Port to new backlight interface selection API
ACPI / video: Fix acpi_video _register vs _unregister_backlight race
...
* acpi-pm:
ACPI / PM: Add missing pm_generic_complete() invocation
ACPI / PM: Turn power resources on and off in the right order during resume
ACPI / PM: Rework device power management to follow ACPI 6
ACPI / PM: Drop stale comment from acpi_power_transition()
* acpi-apei:
GHES: Make NMI handler have a single reader
GHES: Elliminate double-loop in the NMI handler
GHES: Panic right after detection
GHES: Carve out the panic functionality
GHES: Carve out error queueing in a separate function
* acpi-osl:
ACPI / osl: use same type for acpi_predefined_names values as in definition
* acpi-pci:
ACPI / PCI: remove stale list_head in struct acpi_prt_entry
This allows video_detect.c to be build as a module, this is a preparation
patch for the backlight interface selection logic cleanup.
Note this commit also causes acpi_is_video_device() to always be build
indepedent of CONFIG_ACPI_VIDEO, as there is no reason to make its
building depend on CONFIG_ACPI_VIDEO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch implements support for ACPI _CCA object, which is introduced in
ACPIv5.1, can be used for specifying device DMA coherency attribute.
The parsing logic traverses device namespace to parse coherency
information, and stores it in acpi_device_flags. Then uses it to call
arch_setup_dma_ops() when creating each device enumerated in DSDT
during ACPI scan.
This patch also introduces acpi_dma_is_coherent(), which provides
an interface for device drivers to check the coherency information
similarly to the of_dma_is_coherent().
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki