There is no point in having a generic broadcast function if it needs to
have special cases for each callback it broadcasts.
Abstract the error broadcast to only the necessary information and removes
the now unnecessary helper to walk the bus.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
If an Endpoint reported an error with ERR_FATAL, we previously ran driver
error recovery callbacks only for the Endpoint's driver. But if we reset a
Link to recover from the error, all downstream components are affected,
including the Endpoint, any multi-function peers, and children of those
peers.
Initiate the Link reset from the deepest Downstream Port that is
reliable, and call the error recovery callbacks for all its children.
If a Downstream Port (including a Root Port) reports an error, we assume
the Port itself is reliable and we need to reset its downstream Link. In
all other cases (Switch Upstream Ports, Endpoints, Bridges, etc), we assume
the Link leading to the component needs to be reset, so we initiate the
reset at the parent Downstream Port.
This allows two other clean-ups. First, we currently only use a Link
reset, which can only be initiated using a Downstream Port, so we can
remove checks for Endpoints. Second, the Downstream Port where we initiate
the Link reset is reliable (unlike components downstream from it), so the
special cases for error detect and resume are no longer necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
We don't need to be paranoid about the topology changing while handling an
error. If the device has changed in a hotplug capable slot, we can rely on
the presence detection handling to react to a changing topology.
Restore the fatal error handling behavior that existed before merging DPC
with AER with 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and
re-enumeration of devices").
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The secondary bus reset may have link side effects that a hotplug capable
port may incorrectly react to. Use the slot specific reset for hotplug
ports, fixing the undesirable link down-up handling during error
recovering.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: fold in
https://lore.kernel.org/linux-pci/20180926152326.14821-1-keith.busch@intel.com
for issue reported by Stephen Rothwell <sfr@canb.auug.org.au>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The AER driver has never read the config space of an endpoint that reported
a fatal error because the link to that device is considered unreliable.
An ERR_FATAL from an upstream port almost certainly indicates an error on
its upstream link, so we can't expect to reliably read its config space for
the same reason.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Error handling may be running in parallel with a hot removal. Reference
count the device during AER handling so the device can not be freed while
AER wants to reference it.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
This patch provides DPC save and restore capabilities. This is necessary
for the driver to observe DPC events in the event the configuration space
needs to be restored after a reset.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The port's config space may be cleared after a link reset, which wipes out
the bridge's bus and memory windows. Restore the config space that was
saved during probe so we can access downstream devices.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The PCI port driver saves the PCI state after initializing the device with
the applicable service devices. This was, however, before the service
drivers were even registered because PCI probe happens before the
device_initcall initialized those service drivers. The config space state
that the services set up were not being saved. The end result would cause
PCI devices to not react to events that the drivers think they did if the
PCI state ever needed to be restored.
Fix this by changing the service drivers from using the init calls to
having the portdrv driver calling the services directly. This will get the
state saved as desired, while making the relationship between the port
driver and the services under it more explicit in the code.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Now that ASPM is configured for *all* PCIe devices at boot, a problem is
seen with systems that set the FADT NO_ASPM bit. This bit indicates that
the OS should not alter the ASPM state, but when
pcie_aspm_init_link_state() runs it only checks for !aspm_support_enabled.
This misses the ACPI_FADT_NO_ASPM case because that is setting
aspm_disabled.
The result is systems may hang at boot after 1302fcf; avoidable if they
boot with pcie_aspm=off (sets !aspm_support_enabled).
Fix this by having aspm_init_link_state() check for either
!aspm_support_enabled or acpm_disabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201001
Fixes: 1302fcf0d0 ("PCI: Configure *all* devices, not just hot-added ones")
Signed-off-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 89ee9f7680 ("PCI: Add device disconnected state") iterates over
the devices on a parent bus, marks each as disconnected, then marks
each device's children as disconnected using pci_walk_bus().
The same can be achieved more succinctly by calling pci_walk_bus() on
the parent bus. Moreover, this does not need to wait until acquiring
pci_lock_rescan_remove(), so move it out of that critical section.
The critical section in err.c contains a pci_dev_get() / pci_dev_put()
pair which was apparently copy-pasted from pciehp_pci.c. In the latter
it serves the purpose of holding the struct pci_dev in place until the
Command register is updated. err.c doesn't do anything like that, hence
the pair is unnecessary. Remove it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Oza Pawandeep <poza@codeaurora.org>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upon removal of the last device on a bus, the link_state of the bridge
leading to that bus is sought to be torn down by having pci_stop_dev()
call pcie_aspm_exit_link_state().
When ASPM was originally introduced by commit 7d715a6c1a ("PCI: add
PCI Express ASPM support"), it determined whether the device being
removed is the last one by calling list_empty() on the bridge's
subordinate devices list. That didn't work because the device is only
removed from the list slightly later in pci_destroy_dev().
Commit 3419c75e15 ("PCI: properly clean up ASPM link state on device
remove") attempted to fix it by calling list_is_last(), but that's not
correct either because it checks whether the device is at the *end* of
the list, not whether it's the last one *left* in the list. If the user
removes the device which happens to be at the end of the list via sysfs
but other devices are preceding the device in the list, the link_state
is torn down prematurely.
The real fix is to move the invocation of pcie_aspm_exit_link_state() to
pci_destroy_dev() and reinstate the call to list_empty(). Remove a
duplicate check for dev->bus->self because pcie_aspm_exit_link_state()
already contains an identical check.
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: stable@vger.kernel.org # v2.6.26
- To avoid bus errors, enable PASID only if entire path supports End-End
TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller
(Bjorn Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: Rename pci_try_reset_bus() to pci_reset_bus()
PCI: Deprecate pci_reset_bus() and pci_reset_slot() functions
PCI: Unify try slot and bus reset API
PCI: Hide pci_reset_bridge_secondary_bus() from drivers
IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset
PCI: Handle error return from pci_reset_bridge_secondary_bus()
PCI/IOV: Tidy pci_sriov_set_totalvfs()
PCI: Enable PASID only if entire path supports End-End TLP prefixes
# Conflicts:
# drivers/pci/hotplug/pciehp_hpc.c
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
* pci/dpc:
PCI/DPC: Remove indirection waiting for inactive link
PCI/DPC: Use threaded IRQ for bottom half handling
PCI/DPC: Print AER status in DPC event handling
PCI/DPC: Remove rp_pio_status from dpc struct
PCI/DPC: Defer event handling to work queue
PCI/DPC: Leave interrupts enabled while handling event
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
* pci/aspm:
PCI: Remove unnecessary include of <linux/pci-aspm.h>
iwlwifi: Remove unnecessary include of <linux/pci-aspm.h>
ath9k: Remove unnecessary include of <linux/pci-aspm.h>
igb: Remove unnecessary include of <linux/pci-aspm.h>
PCI/ASPM: Convert to use sysfs_match_string() helper
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
* pci/aer:
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI/AER: Remove duplicate PCI_EXP_AER_FLAGS definition
PCI/portdrv: Remove pcie_portdrv_err_handler.slot_reset
PCI/AER: Clear device status bits during ERR_COR handling
PCI/AER: Clear device status bits during ERR_FATAL and ERR_NONFATAL
PCI/AER: Remove ERR_FATAL code from ERR_NONFATAL path
PCI/AER: Factor out ERR_NONFATAL status bit clearing
PCI/AER: Clear only ERR_NONFATAL bits during non-fatal recovery
PCI/AER: Clear only ERR_FATAL status bits during fatal recovery
PCI/AER: Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST
PCI/AER: Add sysfs attributes for rootport cumulative stats
PCI/AER: Add sysfs attributes to provide AER stats and breakdown
PCI/AER: Define aer_stats structure for AER capable devices
PCI/AER: Move internal declarations to drivers/pci/pci.h
PCI/AER: Adopt lspci names for AER error decoding
PCI/AER: Expose internal API for obtaining AER information
# Conflicts:
# drivers/pci/pci.h
If the platform requests Firmware-First error handling, firmware is
responsible for reading and clearing AER status bits. If OSPM also clears
them, we may miss errors. See ACPI v6.2, sec 18.3.2.5 and 18.4.
This race is mostly of theoretical significance, as it is not easy to
reasonably demonstrate it in testing.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: add similar guards to pci_cleanup_aer_uncorrect_error_status()
and pci_aer_clear_fatal_status()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sysfs_match_string() helper returns index of the matching string in an
array. Use it in pcie_aspm_set_policy() to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: squash sysfs_match_string() fix into original patch for issue
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI_EXP_AER_FLAGS was defined twice (with identical definitions), once
under #ifdef CONFIG_ACPI_APEI, and again at the top level. This looks like
my merge error from these commits:
fd3362cb73 ("PCI/AER: Squash aerdrv_core.c into aerdrv.c")
41cbc9eb1a ("PCI/AER: Squash ecrc.c into aerdrv.c")
Remove the duplicate PCI_EXP_AER_FLAGS definition.
Fixes: 41cbc9eb1a ("PCI/AER: Squash ecrc.c into aerdrv.c")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840fe ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Replace suspend_iter() and resume_iter() with a single function pm_iter()
to allow addition of port service callbacks for further power management
phases without having to add another iterator each time.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When an fatal error is received by a non-bridge device, the device is
removed, and pci_stop_and_remove_bus_device() deallocates the device
structure. The freed device structure is used by subsequent code to send
uevents and print messages.
Hold a reference on the device until we're finished using it. This is not
an ideal fix because pcie_do_fatal_recovery() should not use the device at
all after removing it, but that's too big a project for right now.
Fixes: 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and re-enumeration of devices")
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
[bhelgaas: changelog, reduce get/put coverage]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_error_handlers.slot_reset() callback is only used for non-bridge
devices (see broadcast_error_message()). Since portdrv only binds to
bridges, we don't need pcie_portdrv_slot_reset(), so remove it.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove pcie_portdrv_slot_reset() completely]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case of correctable error, the Correctable Error Detected bit in the
Device Status register is set. Clear it after handling the error.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clear the device status bits while handling both ERR_FATAL and ERR_NONFATAL
cases.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: rename to pci_aer_clear_device_status(), declare internal to PCI
core instead of exposing it everywhere]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
broadcast_error_message() is only used for ERR_NONFATAL events, when the
state is always pci_channel_io_normal, so remove the unused alternate path.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_error_resume() clears all ERR_NONFATAL error status bits. This is
exactly what pci_cleanup_aer_uncorrect_error_status(), so use that instead
of duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_cleanup_aer_uncorrect_error_status() is called by driver .slot_reset()
methods when handling ERR_NONFATAL errors. Previously this cleared *all*
the bits, including ERR_FATAL bits.
Since we're only handling ERR_NONFATAL errors, clear only the ERR_NONFATAL
error status bits.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During recovery from fatal errors, we previously called
pci_cleanup_aer_uncorrect_error_status(), which cleared *all* uncorrectable
error status bits (both ERR_FATAL and ERR_NONFATAL).
Instead, call a new pci_aer_clear_fatal_status() that clears only the
ERR_FATAL bits (as indicated by the PCI_ERR_UNCOR_SEVER register).
Based-on-patch-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename pci_reset_bridge_secondary_bus() to pci_bridge_secondary_bus_reset()
and move the declaration from linux/pci.h to drivers/pci.h to be used
internally in PCI directory only.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 01fd61c0b9 ("PCI: Add a return type for
pci_reset_bridge_secondary_bus()") added a return value to the function to
return if a device is accessible following a reset. Callers are not
checking the value.
Pass error code up high in the stack if device is not accessible.
Fixes: 01fd61c0b9 ("PCI: Add a return type for pci_reset_bridge_secondary_bus()")
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Simplify waiting for the contained link to become inactive, removing the
indirection to a unnecessary DPC-specific handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Remove the work struct that was being used to handle a DPC event and use a
threaded IRQ instead.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
A DPC enabled device suppresses ERR_(NON)FATAL messages, preventing the AER
handler from reporting error details. If the DPC trigger reason says the
downstream port detected the error, collect the AER uncorrectable status
for logging, then clear the status.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
We don't need to save the rp pio status across multiple contexts as all
DPC event handling occurs in a single work queue context.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Move all event handling to the existing work queue, which will
make it simpler to pass event information to the handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Now that the DPC driver clears the interrupt status before exiting the
IRQ handler, we don't need to abuse the DPC control register to know if
a shared interrupt is for a new DPC event: a DPC port can not trigger
a second interrupt until the host clears the trigger status later in the
work queue handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
According to the documentation, "pcie_ports=native", linux should use
native AER and DPC services. While that is true for the _OSC method
parsing, this is not the only place that is checked. Should the HEST
list PCIe ports as firmware-first, linux will not use native services.
This happens because aer_acpi_firmware_first() doesn't take 'pcie_ports'
into account. This is wrong. DPC uses the same logic when it decides
whether to load or not, so fixing this also fixes DPC not loading.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: return "false" from bool function (from kbuild robot)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes for rootport statistics (that are cumulative of all
the ERR_* messages seen on this PCI hierarchy).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes to provide total and breakdown of the AERs seen,
into different type of correctable, fatal and nonfatal errors:
/sys/bus/pci/devices/<dev>/aer_dev_correctable
/sys/bus/pci/devices/<dev>/aer_dev_fatal
/sys/bus/pci/devices/<dev>/aer_dev_nonfatal
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define a structure to hold the AER statistics. There are 2 groups of
statistics: dev_* counters that are to be collected for all AER capable
devices and rootport_* counters that are collected for all (AER capable)
rootports only. Allocate and free this structure when device is added or
released (thus counters survive the lifetime of the device).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since pci_aer_init() and pci_no_aer() are used only internally, move their
declarations to the PCI internal header file. Also, no one cares about
return value of pci_aer_init(), so make it void.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
lspci uses abbreviated naming for AER error strings. Adopt the same naming
convention for the AER printing so they match.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Export some common AER functions and structures for other PCI core drivers
to use. Since this is making the function externally visible inside the
PCI core, prepend "aer_" to the function name.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: move AER declarations from linux/aer.h to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Use "PCI Express" consistently in Kconfig text. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Hoist aerdrv.c, aer_inject.c up to drivers/pci/pcie/ so they're next to
other PCIe service drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Most of the things in aerdrv.h are only used in aerdrv.c, so move them
there. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The aer_irq() declaration is the only thing needed by aer_inject.c. Move
it to portdrv.h so we eventually get rid of aerdrv.h completely. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Move pcie_aer_get_firmware_first() to portdrv.h, where it can be more
easily shared between AER and DPC. Then DPC no longer needs to include
aer/aerdrv.h. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
pcie_port_bus_type is already declared in portdrv.h, so remove the
unnecessary duplicate declaration in aerdrv.h. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reorder code to group probe/remove stuff together. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use ACPI
hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
* pci/hotplug:
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: shpchp: Use dev_printk() for OSHP-related messages
PCI: shpchp: Remove get_hp_hw_control_from_firmware() wrapper
PCI: shpchp: Remove acpi_get_hp_hw_control_from_firmware() flags
PCI: shpchp: Rely on previous _OSC results
PCI: shpchp: Request SHPC control via _OSC when adding host bridge
PCI: shpchp: Convert SHPC to be builtin only
PCI: pciehp: Make pciehp_is_native() stricter
PCI: pciehp: Rename host->native_hotplug to host->native_pcie_hotplug
PCI: pciehp: Request control of native hotplug only if supported
PCI: pciehp: Clear Presence Detect and Data Link Layer Status Changed on resume
PCI: pnv_php: Add missing of_node_put()
PCI: pciehp: Add quirk for Command Completed errata
PCI: Add Qualcomm vendor ID
PCI: ibmphp: Fix use-before-set in get_max_bus_speed()
# Conflicts:
# drivers/acpi/pci_root.c
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
* pci/aspm:
PCI/ACPI: Request LTR control from platform before using it
PCI/ASPM: Disable ASPM L1.2 Substate if we don't have LTR
The AER driver only needed the pcie_device to get to the port pci_dev.
Save the pci_dev pointer directly in struct aer_rpc and remove the
unnecessary indirection.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Decode the Requester ID from the AER Error Source Register into domain/
bus/device/function format to match other logging. In cases where the ID
matches the device used for pci_err(), drop the extra ID completely so we
don't print it twice.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just move the actual function up so that it is visible to its user
aer_recover_queue().
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Our goal is to handle ERR_FATAL errors similarly, whether they are reported
via AER or via DPC. A previous commit changed AER so it handles ERR_FATAL
by calling driver .remove() methods and resetting the Link. DPC already
does that (although the Link reset is done automatically by hardware and
happens before we call the driver .remove() methods).
Restructure the DPC code so it calls the same pcie_do_fatal_recovery()
interface used by AER. This makes it clearer that we want to use the same
path.
Implement the .reset_link() method used by pcie_do_fatal_recovery(). For
DPC, the actual reset is done automatically by hardware, so we really only
have to wait for the Link to be inactive, then release the Port from DPC.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, DPC_FATAL is not a bitfield, can be sequential]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pass the service type to pcie_do_fatal_recovery() instead of assuming AER.
We will make DPC also use pcie_do_fatal_recovery(), and it needs to do
things a little differently for AER and DPC.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe ERR_NONFATAL errors mean a particular transaction is unreliable but
the Link is otherwise fully functional (PCIe r4.0, sec 6.2.2).
The AER driver handles these by logging the error details and calling
driver-supplied pci_error_handlers callbacks. It does not reset downstream
devices, does not remove them from the PCI subsystem, does not re-enumerate
them, and does not call their driver .remove() or .probe() methods.
But DPC driver previously enabled DPC on ERR_NONFATAL, so if the hardware
supports DPC, these errors caused a Link reset (performed automatically by
the hardware), followed by the DPC driver removing affected devices (which
calls their .remove() methods), bringing the Link back up, and
re-enumerating (which calls driver .probe() methods).
Disable ERR_NONFATAL DPC triggering so these errors will only be handled by
AER. This means drivers won't have to deal with different usage of their
pci_error_handlers callbacks and .probe() and .remove() methods based on
whether the platform has DPC support.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pciehp_is_native() returned true for any PCI device in a
hierarchy where _OSC says we can use pciehp. This is incorrect because
bridges without PCI_EXP_SLTCAP_HPC capability should be managed by acpiphp
instead.
Improve pciehp_is_native() to return true only when PCI_EXP_SLTCAP_HPC is
set and the pciehp driver is present. In any other case return false
to let acpiphp handle those.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: remove NULL pointer check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename host->native_hotplug to host->native_pcie_hotplug to make room for a
similar flag for SHPC hotplug.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the error reporting callbacks from aerdrv_core.c to err.c, where they
can be used by DPC in addition to AER.
As part of aerdrv_core.c, these callbacks were built under CONFIG_PCIEAER.
Moving them to the new err.c means they will now be built under
CONFIG_PCIEPORTBUS, so adjust the definition of pci_uevent_ers() to match.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: in reset_link(), initialize "driver" even if CONFIG_PCIEAER is
unset, update pci_uevent_ers() #ifdef wrapper]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename error recovery interfaces with "pcie_" prefix so they can be made
non-static.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: move declaration to later patch, leave functions static]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
PCIe ERR_FATAL errors mean the Link is unreliable. Components on the Link
may need to be reset to return to reliable operation (PCIe r4.0, sec
6.2.2). We previously handled these errors much differently depending on
whether the platform supports Downstream Port Containment (DPC) (PCIe r4.0,
sec 6.2.10) or not.
The AER driver has historically logged the error details, called
driver-supplied pci_error_handlers callbacks, and reset the Link. This
reset downstream devices, but did not remove them from the PCI subsystem,
re-enumerate them, or call their driver .remove() or .probe() methods.
DPC is different because the hardware automatically disables the Link when
it detects ERR_FATAL, which resets downstream devices. There's no
opportunity for pci_error_handlers callbacks before resetting the Link.
The DPC driver removes affected devices (which calls their driver .remove()
methods), brings the Link back up, and re-enumerates (which calls driver
.probe() methods).
Align AER ERR_FATAL handling with DPC by resetting the Link in software,
skipping the driver pci_error_handlers callbacks, removing the devices from
the PCI subsystem, and re-enumerating. The idea is that drivers and
devices should see the same behavior for ERR_FATAL events, regardless of
whether they're handled by AER or DPC.
Here are the basic ERR_FATAL recovery steps, showing the previous AER
behavior, the AER behavior after this patch, and the DPC behavior:
AER AER DPC
previous new behavior
-------- --- --------
Log error yes yes yes (minimal)
drv.error_detected() yes no no
Reset Link yes yes yes
drv.mmio_enabled() yes no no
drv.slot_reset() yes no no
drv.resume() yes no no
Remove PCI devices no yes yes
(calls drv.remove())
Re-enumerate no yes yes
(calls drv.probe())
N.B. With DPC, the Link reset happens before the driver .remove() calls,
while with AER, the reset happens *after* the .remove() calls. The goal is
to eventually do the reset before .remove() for AER as well.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, squash doc patch into this, remove unused
"result_data"]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Clients such as hotplug and Downstream Port Containment (DPC) both need to
wait until a link becomes active or inactive.
Add a generic pcie_wait_link_active() interface and use it instead of
duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The generic IRQ handling code ensures that an interrupt handler runs with
its interrupt masked or disabled. If the interrupt is level-triggered, the
interrupt handler must tell its device to stop asserting the interrupt
before returning. If it doesn't, we will immediately take the interrupt
again when the handler returns and the generic code unmasks the interrupt.
The driver doesn't know whether its interrupt is edge- or level-triggered,
so it must clear its interrupt source directly in its interrupt handler.
Previously we cleared the DPC interrupt status in the bottom half, i.e., in
deferred work, which can cause an interrupt storm if the DPC interrupt
happens to be level-triggered, e.g., if we're using INTx instead of MSI.
Clear the DPC interrupt status bit in the interrupt handler, not in the
deferred work.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
When a PCIe AER error occurs, the TLP header information is printed in the
kernel message but it is missing from the tracepoint. A userspace program
can use this information in the tracepoint to better analyze problems.
To enable the tracepoint:
echo 1 > /sys/kernel/debug/tracing/events/ras/aer_event/enable
Example tracepoint output:
$ cat /sys/kernel/debug/tracing/trace
aer_event: 0000:01:00.0
PCIe Bus Error: severity=Uncorrected, non-fatal, Completer Abort
TLP Header={0x0,0x1,0x2,0x3}
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
AER errors can be reported natively (Linux AER driver fields interrupts and
reads error state directly from hardware) or via the ACPI/APEI/GHES/CPER
path (platform firmware reads error state from hardware and sends it to
Linux via ACPI interfaces).
Previously the same error would produce different output depending on
whether it was reported natively or via ACPI. The CPER path resulted in
hard-to-understand messages, without a prefix. Instead use
__aer_print_error() for both native AER and CPER to provide a more
consistent log format.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
02bfeb4842 ("PCI/portdrv: Simplify PCIe feature permission checking")
removed the only call of pcie_port_acpi_setup() and removed portdrv_acpi.o
from the Makefile, but I forgot to remove pcie_port_acpi_setup() itself.
Remove pcie_port_acpi_setup() and the drivers/pci/pcie/portdrv_acpi.c file.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When in the ASPM L1.0 state (but not the PCI-PM L1.0 state), the most
recent LTR value and the LTR_L1.2_THRESHOLD determines whether the link
enters the L1.2 substate.
If we don't have LTR enabled, prevent the use of ASPM L1.2.
PCI-PM L1.2 may still be used because it doesn't depend on
LTR_L1.2_THRESHOLD (see PCIe r4.0, sec 5.5.1).
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
* pci/misc:
PCI: Always define the of_node helpers
PCI: Tidy comments
PCI: Tidy Makefiles
mcb: Add Altera PCI ID to mcb-pci
PCI: Add Altera vendor ID
PCI: Report quirks that take more than 10ms
PCI: Report quirk timings with pci_info() instead of pr_debug()
PCI: Fix NULL pointer dereference in of_pci_bus_find_domain_nr()
rapidio/tsi721: use PCI_EXP_DEVCTL2_COMP_TIMEOUT macro
Rename pcie-dpc.c to dpc.c. The path "drivers/pci/pcie/pcie-dpc.c" has
more occurrences of "pci" than necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit eed85ff4c0 ("PCI/DPC: Enable DPC only if AER is available") made
DPC control dependent whether AER is enabled in the OS. However, it does
not take into account situations where BIOS has not given OS control of
AER:
acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
acpi PNP0A08:00: _OSC: platform does not support [AER]
acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME PCIeCapability]
I think here it is better not to enable DPC even if the capability is
available because then it would be against what "Determination of DPC
Control" note in PCIe 4.0 sec 6.1.10 recommends.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Replace pci_find_ext_capability(..., PCI_EXT_CAP_ID_ERR) calls with
pci_dev->aer_cap.
pci_dev->aer_cap is initialized in pci_init_capabilities(), which happens
before any of these users of the AER Capability.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The platform may restrict the OS's use of PCIe services, e.g., via the ACPI
_OSC method. The user may use "pcie_ports=native" to force the port driver
to use PCIe services even if the platform asked us not to.
The "pcie_ports=native" parameter determines the setting of
pcie_ports_auto. Rename this to pcie_ports_native and reverse the
sense to simplify the code.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"pcie_ports_auto" is only used inside the PCIe port driver itself, so
move it from include/linux/pci.h to portdrv.h so it's not visible to the
whole kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "pcie_ports=auto" parameter set pcie_ports_disabled and pcie_ports_auto
to their compiled-in defaults, so specifying the parameter is the same as
not using it at all.
Remove the "pcie_ports=auto" parameter and update the documentation.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
7570a333d8 ("PCI: Add pcie_hp=nomsi to disable MSI/MSI-X for pciehp
driver") added the "pcie_hp=nomsi" kernel parameter to work around this
error on shutdown:
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 1081, comm: reboot Not tainted 3.2.0 #1
...
Disabling IRQ #16
This happened on an unspecified system (possibly involving the Integrated
Device Technology, Inc. Device 807f bridge) where "an un-wanted interrupt
is generated when PCI driver switches from MSI/MSI-X to INTx while shutting
down the device."
The implication was that the device was buggy, but it is normal for a
device to use INTx after MSI/MSI-X have been disabled. The only problem
was that the driver was still attached and it wasn't prepared for INTx
interrupts. Prarit Bhargava fixed this issue with fda78d7a0e ("PCI/MSI:
Stop disabling MSI/MSI-X in pci_device_shutdown()").
There is no automated way to set this parameter, so it's not very useful
for distributions or end users. It's really only useful for debugging, and
we have "pci=nomsi" for that purpose.
Revert 7570a333d8 to remove the "pcie_hp=nomsi" parameter.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
CC: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
CC: Prarit Bhargava <prarit@redhat.com>
portdrv_pci.c doesn't use anything from <linux/pci-aspm.h>. Remove the
include of it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some PCIe features (AER, DPC, hotplug, PME) can be managed by either the
platform firmware or the OS, so the host bridge driver may have to request
permission from the platform before using them. On ACPI systems, this is
done by negotiate_os_control() in acpi_pci_root_add().
The PCIe port driver later uses pcie_port_platform_notify() and
pcie_port_acpi_setup() to figure out whether it can use these features.
But all we need is a single bit for each service, so these interfaces are
needlessly complicated.
Simplify this by adding bits in the struct pci_host_bridge to show when the
OS has permission to use each feature:
+ unsigned int native_aer:1; /* OS may use PCIe AER */
+ unsigned int native_hotplug:1; /* OS may use PCIe hotplug */
+ unsigned int native_pme:1; /* OS may use PCIe PME */
These are set when we create a host bridge, and the host bridge driver can
clear the bits corresponding to any feature the platform doesn't want us to
use.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No driver registers for PCIE_PORT_SERVICE_VC, so remove it.
This removes the VC "service" files from /sys/bus/pci_express/devices,
e.g., 0000:07:00.0:pcie108, 0000:08:04.0:pcie208 (all the files that
contained "8" as the last digit of the "pcieXXX" part). The port driver
created these files for PCIe port devices that have a VC Capability.
Since this reduces PCIE_PORT_DEVICE_MAXSERVICES and moves DPC down into the
spot where VC used to be, the DPC sysfs files will now be named "pcieXX8".
I don't think there's anything useful userspace can do with those files, so
I hope nobody cares about these filenames.
There is no VC driver that calls pcie_port_service_register(), so there
never was a /sys/bus/pci_express/drivers/vc directory.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The pcie_port_bus_type must be registered before drivers that depend on it
can be registered. Those drivers include:
pcied_init() # PCIe native hotplug driver
aer_service_init() # AER driver
dpc_service_init() # DPC driver
pcie_pme_service_init() # PME driver
Previously we registered pcie_port_bus_type from pcie_portdrv_init(), a
device_initcall. The callers of pcie_port_service_register() (above) are
also device_initcalls. This is fragile because the device_initcall
ordering depends on link order, which is not explicit.
Register pcie_port_bus_type from pci_driver_init() along with pci_bus_type.
This removes the link order dependency between portdrv and the pciehp, AER,
DPC, and PCIe PME drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The "pcie_ports=compat" kernel parameter sets pcie_ports_disabled, which is
intended to disable the PCIe port driver. But even when it was disabled,
we registered pcie_portdriver so we could work around a BIOS PME issue (see
fe31e69740 ("PCI/PCIe: Clear Root PME Status bits early during system
resume")).
Registering the driver meant that the pcie_portdrv_probe() path called
pci_enable_device(), pci_save_state(), pm_runtime_set_autosuspend_delay(),
pm_runtime_use_autosuspend(), etc., even when the driver was disabled.
We've since moved the BIOS PME workaround from the port driver to the core,
so stop registering the PCIe port driver in compat mode.
This means "pcie_ports=compat" will now be basically the same as turning
off CONFIG_PCIEPORTBUS completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Indent things so they line up neatly and remove extra blank lines and
superfluous comments. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fe31e69740 ("PCI/PCIe: Clear Root PME Status bits early during system
resume") added a .resume_noirq() callback to the PCIe port driver to clear
the PME Status bit during resume to work around a BIOS issue.
The BIOS evidently enabled PME interrupts for ACPI-based runtime wakeups
but did not clear the PME Status bit during resume, which meant PMEs after
resume did not trigger interrupts because PME Status did not transition
from cleared to set.
The fix was in the PCIe port driver, so it worked when CONFIG_PCIEPORTBUS
was set. But I think we *always* want the fix because the platform may use
PME interrupts even if Linux is built without the PCIe port driver.
Move the fix from the port driver to the PCI core so we can work around
this "PME doesn't work after waking from a sleep state" issue regardless of
CONFIG_PCIEPORTBUS.
[bhelgaas: folded in warning fix from Arnd Bergmann <arnd@arndb.de>:
https://lkml.kernel.org/r/20180328134747.2062348-1-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pcie_clear_root_pme_status() from the port driver to the PCI core so
it will be available even when the port driver isn't present. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
pcieport_if.h contained the interfaces to register port service driver,
e.g., pcie_port_service_register(). portdrv.h contained internal data
structures of the port driver.
I don't think it's worth keeping those files separate, since both headers
and their users are all inside the PCI core.
Merge pcieport_if.h directly in drivers/pci/pcie/portdrv.h and update the
users to include that instead.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Previously we emitted a warning if we tried to configure common clock mode
the link was already configured to common clock mode by the UEFI BIOS.
Bail out silently in that case instead of emitting the warning:
pci 0004:00:00.0: ASPM: Could not configure common clock
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
aspm_calc_l1ss_info() computes l1_2_threshold in microseconds as:
l1_2_threshold = 2 + 4 + t_common_mode + t_power_on;
where t_common_mode is at most 255us:
PCI_L1SS_CAP_CM_RESTORE_TIME 0x0000ff00 <-- 8 bits; <256us
and t_power_on is at most 31 * 100us = 3100us:
PCI_L1SS_CAP_P_PWR_ON_VALUE 0x00f80000 <-- 5 bits; <32
PCI_L1SS_CAP_P_PWR_ON_SCALE 0x00030000 <-- *2us, *10us, or *100us
So l1_2_threshold is at most 2 + 4 + 255 + 3100 = 3361, which means
threshold_ns is at most 3361 * 1000 = 3361000, which easily fits in a
u32.
Declare threshold_ns as u32, not u64. This fixes a Coverity warning.
Addresses-Coverity-ID: 1462501
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Move pcieport_if.h from include/linux to drivers/pci/pcie/pcieport_if.h
because the interfaces there are only used by the PCI core.
Replace all uses of #include<linux/pcieport_if.h> with relative paths to
the new file location, e.g., #include "../pcieport_if.h"
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJad5lgAAoJEFmIoMA60/r8s2kQAI3PztawDpaCP9Z12pkbBHSt
Ho0xTyk9rCZi9kQJbNjc+a+QrlA3QmTHXIXerB3LSWoh7M+XhsECjem92eHpgLNS
JvYPhTfOrCr0vdiAmOz6hD0AqN/psrbfzgiJhSwomsGEFS77k7kERSJckRv81sxb
Aj5F/WjucAgLorwm4auveAJEQ7atE7/6pkXzoqYm4G6NLOb46jUcRGndrnvXZBlz
fws8fBM4BHyi7i25CYQl24tFq1CGax1rIPgLg+4KnH76bQk/N6Ju0sGVSzfh+hG8
SIerK9bJbzGRAuNKoxB3aO1dyzsK3x9WztE2mG98w5trOISPIR1FqnvC/225FWAU
d6eIXiC7wKnEx+DElNTzCjzfHc7SAJoupO32H7CoiTe5zPUlWlxJ1zLYkK1gt50q
m8PRBiYTglxyznzrO0drtcdjEzvbdZNRrsYnul4wi1vSHzjk6F6XLtzT10XWM1M1
1pXLB8384FTj0Hu4bq6Y3Aivkmz0Sf+eQM2NaOwe+Zj7/1VV0d3lvi4LUXkqzLCA
FoXPJSMxG2Qu+iflCeYRQBJjExaZH3eNLZ3dT6QpcJrjaFVedd9u5DeeFqNL27zV
bhr8TdqrR4p4rc8EBAGoCapw96IxLZROKB3gxbrZVOpfIZpzthwHbElHX6aqUgF4
w/EV1JWs36WXWaxFk8wd
=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9 when
using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts as well
as "normal" interrupts, and then use that to implement local_t for a ~4x
speedup vs the current atomics-based implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor Interface
(OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe hotpluggable
memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit VDSO.
- Freescale updates from Scott:
"Contains fixes for CPM GPIO and an FSL PCI erratum workaround, plus a
minor cleanup patch."
As well as quite a lot of other changes all over the place, and small fixes and
cleanups as always.
Thanks to:
Alan Modra, Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andreas
Schwab, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman
Khandual, Anton Blanchard, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Bhaktipriya Shridhar, Bryant G. Ly, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Cyril Bur, David Gibson, Desnes A. Nunes
do Rosario, Dmitry Torokhov, Frederic Barrat, Geert Uytterhoeven, Guilherme G.
Piccoli, Gustavo A. R. Silva, Gustavo Romero, Ivan Mikhaylov, Joakim
Tjernlund, Joe Perches, Josh Poimboeuf, Juan J. Alvarez, Julia Cartwright,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre,
Michael Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud, Ram Pai,
Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee, Simon Guo, Stewart
Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann, Vaibhav Jain, Vasyl
Gomonovych.
-----BEGIN PGP SIGNATURE-----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=3rYn
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
* pci/spdx:
PCI: Add SPDX GPL-2.0+ to replace implicit GPL v2 or later statement
PCI: Add SPDX GPL-2.0+ to replace GPL v2 or later boilerplate
PCI: Add SPDX GPL-2.0 to replace COPYING boilerplate
PCI: Add SPDX GPL-2.0 to replace GPL v2 boilerplate
PCI: Add SPDX GPL-2.0 when no license was specified
* pci/misc:
PCI: Add dummy pci_irqd_intx_xlate() for CONFIG_PCI=n build
PCI: Add wrappers for dev_printk()
PCI: Remove unnecessary messages for memory allocation failures
PCI: Add #defines for Completion Timeout Disable feature
hinic: Replace PCI pool old API
net: e100: Replace PCI pool old API
block: DAC960: Replace PCI pool old API
MAINTAINERS: Include more PCI files
PCI: Remove unneeded kallsyms include
powerpc/pci: Unroll two pass loop when scanning bridges
powerpc/pci: Use for_each_pci_bridge() helper
* pci/dpc:
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
PCI/DPC: Process RP PIO details only if RP PIO extensions supported
PCI/DPC: Read RP PIO Log Size once at probe
PCI/DPC: Rename struct dpc_dev.rp to rp_extensions
PCI/DPC: Add local variable for DPC capability offset
PCI/DPC: Rename interrupt_event_handler() to dpc_work()
PCI/DPC: Fix interrupt message number print
PCI/DPC: Enable DPC only if AER is available
PCI/DPC: Fix shared interrupt handling
Add definitions for DPC Status register fields and use them in the code.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
dpc_process_rp_pio_error() only calls dpc_rp_pio_get_info(), so squash them
together. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
We read and immediately print the RP PIO log registers. We don't save
them, so there's no need to define structs for them. Remove the structs
and read the registers into local variables instead. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Move the dpc->rp_pio_status assignment into dpc_rp_pio_get_info() since
that's where we read rp_pio->status anway. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Separating dpc_rp_pio_print_error() doesn't really provide any useful
abstraction, so squash it into its caller, dpc_rp_pio_get_info(). No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
In dpc_probe(), we set dpc->rp_log_size to zero if we think the hardware
reports an invalid size. In this case, we could have dpc->rp_extensions
set but dpc->rp_log_size == 0, and we should print the basic RP PIO
registers but not the variable-size portion. We already checked for
dpc->rp_log_size < 4 above, so this patch is just for consistency of style.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
In dpc_rp_pio_get_info() rename the local "status" variable to
"dpc_status". This is to make room for another variable named "status" in
a subsequent patch. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Separating dpc_rp_pio_print_tlp_header() doesn't really provide any useful
abstraction, so squash it into its caller, dpc_rp_pio_print_error(). No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The RP PIO registers (status, mask, severity, etc) are only implemented if
the "RP Extensions for DPC" bit is set in the DPC Capabilities register.
Previously we called dpc_process_rp_pio_error(), which reads and decodes
those RP PIO registers, whenever the DPC Status register indicated an "RP
PIO error" (Trigger Reason == 3 and Trigger Reason Extension == 0).
It does seem reasonable to assume that DPC Status would only indicate an RP
PIO error if the RP extensions are supported, but PCIe r4.0, sec 7.9.15.4,
is actually not explicit about that: it does not say "Trigger Reason
Extension == 0 is valid only for Root Ports that support RP Extensions for
DPC."
Check whether the RP Extensions for DPC are supported before trying to read
the RP PIO registers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The RP PIO Log Size is a read-only field in the DPC Capability, so it is
constant and known at probe-time, but previously we read it every time we
processed an RP PIO error.
Read it once in dpc_probe() (if the RP Extensions for DPC are supported)
and remember the size in struct dpc_dev. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
"rp" is ambiguous: it might mean "this DPC device is a Root Port." But in
fact, it means "this DPC device is a Root Port *and* it supports a set of
DPC Extensions."
Rename "rp" to "rp_extensions" to make this more clear. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Add a local variable for DPC capability offset and replace repeated use of
"dpc->cap_pos" with simply "cap". No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Add SPDX GPL-2.0 to all PCI files that referred to the kernel default
"COPYING" file, which specifies GPL version 2.
Remove the boilerplate language referring to the GPL and "COPYING", relying
on the assertion in b24413180f ("License cleanup: add SPDX GPL-2.0
license identifier to files with no license") that the SPDX identifier may
be used instead of the full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX GPL-2.0 to all PCI files that specified the GPL version 2 license.
Remove the boilerplate GPL version 2 language, relying on the assertion in
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") that the SPDX identifier may be used instead of the
full boilerplate text.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices can go offline when erors reported. This patch adds a change
to the kernel object and lets udev know of error. When device resumes,
a change is also set reporting device as online. Therefore, EEH and
AER events are better propagated to user space for PCI devices in all
arches.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rename interrupt_event_handler() to dpc_work() so there's more useful
information in stack traces and similar situations. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
The interrupt message number is the first 5 bits, but the driver was
masking only the first 4 bits. Fix that by using the existing
define.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: remove reformatting (done by another patch)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "Determination of DPC Control" implementation note in PCIe r4.0, sec
6.1.10, recommends the operating system always link DPC control to the
control of AER, as the two functionalities are strongly connected.
To avoid conflicts over whether platform firmware or the OS controls DPC,
enable DPC only if AER is enabled in the OS, and the device's error
handling does not have firmware-first AER handling.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI-specific dev_printk() wrappers and use them to simplify the code
slightly. No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: squash into one patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
get_device_error_info() reads error information from registers in the AER
capability. If we call it for a device that has no AER capability, it
should return an error, but previously it returned success.
Return 0 (error) if the device doesn't have an AER capability.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
DPC supports shared interrupts, but it plays very loosely with testing
whether the interrupt is generated by DPC before generating spurious log
messages, such as:
dpc 0000:10:01.2:pcie010: DPC containment event, status:0x1f00 source:0x0000
Testing the status register for zero or -1 is not sufficient when the
device supports the RP PIO First Error Pointer register. Change this to
test whether the interrupt is enabled in the control register, retaining
the device present test, and that the status reports the interrupt as
signaled and DPC is triggered, clearing as a spurious interrupt otherwise.
Additionally, since the interrupt is actually serviced by a workqueue,
disable the interrupt in the control register until that completes or else
we may never see it execute due to further incoming interrupts. A software
generated DPC floods the system otherwise.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Make the PCIe port driver set DPM_FLAG_SMART_SUSPEND and
DPM_FLAG_LEAVE_SUSPENDED for the devices handled by it to benefit
from the opportunistic optimizations in the PCI layer enabled by
these flags.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r3.1, sec 5.5.1, LTR_L1.2_THRESHOLD determines whether we enter
the L1.2 Link state: if L1.2 is enabled and downstream devices have
reported that they can tolerate latency of at least LTR_L1.2_THRESHOLD, we
must enter L1.2 when CLKREQ# is de-asserted.
The implication is that LTR_L1.2_THRESHOLD is the time required to
transition the Link from L0 to L1.2 and back to L0, and per sec 5.5.3.3.1,
Figures 5-16 and 5-17, it appears that the absolute minimum time for those
transitions would be T(POWER_OFF) + T(L1.2) + T(POWER_ON) + T(COMMONMODE).
Therefore, compute LTR_L1.2_THRESHOLD as:
2us T(POWER_OFF)
+ 4us T(L1.2)
+ T(POWER_ON)
+ T(COMMONMODE)
= LTR_L1.2_THRESHOLD
Previously we set LTR_L1.2_THRESHOLD to a fixed value of 163840ns
(163.84us):
#define LTR_L1_2_THRESHOLD_BITS ((1 << 21) | (1 << 23) | (1 << 30))
((1 << 21) | (1 << 23) | (1 << 30)) = 0x40a00000
LTR_L1.2_THRESHOLD_Value = (0x40a00000 & 0x03ff0000) >> 16 = 0xa0 = 160
LTR_L1.2_THRESHOLD_Scale = (0x40a00000 & 0xe0000000) >> 29 = 0x2 (* 1024ns)
LTR_L1.2_THRESHOLD = 160 * 1024ns = 163840ns
Obviously this doesn't account for the circuit characteristics of different
implementations.
Note that while firmware may enable LTR, Linux itself currently does not
enable LTR. When L1.2 is enabled but LTR is not, LTR_L1.2_THRESHOLD is
ignored and we always enter L1.2 when it is enabled and CLKREQ# is
de-asserted. So this patch should not have any effect unless firmware
enables LTR.
Fixes: f1f0366dd6 ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Link: https://www.coreboot.org/pipermail/coreboot-gerrit/2015-March/021134.html
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Cc: Kenji Chen <kenji.chen@intel.com>
Cc: Patrick Georgi <pgeorgi@google.com>
Cc: Rajat Jain <rajatja@google.com>
PCIe correctable errors are corrected by hardware. Software may log them,
but no other software intervention is required.
There are two paths to enter the AER recovery code: (1) the native path
where Linux fields the AER interrupt and reads the AER registers directly,
and (2) the ACPI path where firmware reads the AER registers and hands them
off to Linux via the ACPI APEI path.
The AER do_recovery() function calls driver error reporting callbacks
(error_detected(), mmio_enabled(), resume(), etc), attempts recovery (for
fatal errors), and logs a "AER: Device recovery successful" message.
Since there's nothing to recover for correctable errors, the native path
already skips do_recovery(), so it doesn't call the driver callbacks and or
emit the message. Make the APEI path do the same.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
* pci/msi:
PCI/portdrv: Compute MSI/MSI-X IRQ vectors after final allocation
PCI/portdrv: Factor out Interrupt Message Number lookup
PCI/portdrv: Consolidate comments
PCI/portdrv: Add #defines for AER and DPC Interrupt Message Number masks
* pci/misc:
PCI: Fix kernel-doc build warning
PCI: Move PCI_QUIRKS to the PCI bus menu
alpha/PCI: Make pdev_save_srm_config() static
PCI: Remove unused declarations
PCI: Remove redundant pci_dev, pci_bus, resource declarations
PCI: Remove redundant pcibios_set_master() declarations
PCI/PME: Handle invalid data when reading Root Status
x86/pci/intel_mid_pci: Constify intel_mid_pci_ops and make it __initconst
PCI: Constify pci_dev_type structure
* pci/aspm:
PCI/ASPM: Add L1 Substates definitions
PCI/ASPM: Reformat ASPM register definitions
PCI/ASPM: Use correct capability pointer to program LTR_L1.2_THRESHOLD
PCI/ASPM: Account for downstream device's Port Common_Mode_Restore_Time
PCI/ASPM: Deal with missing root ports in link state handling
Add and use #defines for L1 Substate register fields instead of hard-coding
the masks. Also update comments to use names from the spec. No functional
change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Previously we programmed the LTR_L1.2_THRESHOLD in the parent (upstream)
device using the capability pointer of the *child* (downstream) device,
which corrupted some random word of the parent's config space.
Use the parent's L1 SS capability pointer to program its
LTR_L1.2_THRESHOLD.
Fixes: aeda9adeba ("PCI/ASPM: Configure L1 substate settings")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
CC: stable@vger.kernel.org # v4.11+
CC: Rajat Jain <rajatja@google.com>
Every Port that supports the L1.2 substate advertises its Port
Common_Mode_Restore_Time, i.e., the time the Port requires to re-establish
common mode when exiting L1.2 (see PCIe r3.1, sec 7.33.2).
Per sec 5.5.3.3.1, when exiting L1.2, the Downstream Port (the device at
the upstream end of the link) must send TS1 training sequences for at least
T(COMMONMODE) after it detects electrical idle exit on the Link. We want
this to be long enough for both ends of the Link, so we should set it to
the maximum of the Port Common_Mode_Restore_Time for the upstream and
downstream components on the Link.
Previously we only looked at the Port Common_Mode_Restore_Time of the
upstream device, so if the downstream device required more time, we didn't
program the upstream device's T(COMMONMODE) correctly.
Fixes: f1f0366dd6 ("PCI/ASPM: Calculate and save the L1.2 timing parameters")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Rajat Jain <rajatja@google.com>
CC: stable@vger.kernel.org # v4.11+
PCIe PME and native hotplug share the same interrupt number, so hotplug
interrupts are also processed by PME. In some cases, e.g., a Link Down
interrupt, a device may be present but unreachable, so when we try to
read its Root Status register, the read fails and we get all ones data
(0xffffffff).
Previously, we interpreted that data as PCI_EXP_RTSTA_PME being set, i.e.,
"some device has asserted PME," so we scheduled pcie_pme_work_fn(). This
caused an infinite loop because pcie_pme_work_fn() tried to handle PME
requests until PCI_EXP_RTSTA_PME is cleared, but with the link down,
PCI_EXP_RTSTA_PME can't be cleared.
Check for the invalid 0xffffffff data everywhere we read the Root Status
register.
1469d17dd3 ("PCI: pciehp: Handle invalid data when reading from
non-existent devices") added similar checks in the hotplug driver.
Signed-off-by: Qiang Zheng <zhengqiang10@huawei.com>
[bhelgaas: changelog, also check in pcie_pme_work_fn(), use "~0" to follow
other similar checks]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some of the PCIe services such as AER are being left enabled during
shutdown. This might cause spurious AER errors while SOC is being powered
down.
Clean up the PCIe services gracefully during shutdown to clear these false
positives.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
When setting up portdrv MSI/MSI-X interrupts, we previously allocated the
maximum possible number of vectors, read the Interrupt Message Numbers for
each service, saved the IRQ for each, freed the vectors, and finally used
the largest Message Number to reallocate only as many vectors as we need.
The problem is that freeing the vectors invalidates their IRQs, so the
saved IRQ numbers may now be invalid, which can result in errors like
this:
pcie_pme: probe of 0000:00:00.0:pcie001 failed with error -22
pciehp 0000:00:00.0:pcie004: Cannot get irq 20 for the hotplug controller
aer: probe of 0000:00:00.0:pcie002 failed with error -22
dpc 0000:00:00.0:pcie010: request IRQ22 failed: -22
Change the setup so we save the Interrupt Message Numbers (not the IRQs)
before we free the original setup, then use the Message Numbers to compute
the IRQs (via pci_irq_vector()) *after* we reallocate the vectors.
This should always be safe for MSI-X because the Message Numbers are fixed.
For MSI, the hardware is allowed to change Message Numbers when we update
the MSI Multiple Message Enable field when reallocating the vectors, but
since we allocate enough vectors to accommodate the largest Message Number
we found, that's unlikely. See PCIe r3.1, sec 7.8.2, 7.10.10, 7.31.2.
Fixes: 3674cc49da ("PCI/portdrv: Use pci_irq_alloc_vectors()")
Based-on-patch-by: Dongdong Liu <liudongdong3@huawei.com>
Tested-by: Dongdong Liu <liudongdong3@huawei.com> # HiSilicon hip08
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Factor out Interrupt Message Number lookup from the MSI/MSI-X interrupt
setup. One side effect is that we only have to check once to see if we
have enough vectors for all the services. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Keith Busch