When accessing the mc_devices list of memory controller descriptors, we
need to hold mem_ctls_mutex. This was not always the case, fix that.
Make all external callers call a version which grabs the mutex since the
last is local to edac_mc.c.
Reported-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
They're both running only when ->edac_check is initialized so remove
that check from the workqueue function itself. Synchronize/generalize
the ->op_state check between the two.
Kill useless comments, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
We use the ->edac_check function pointers to determine whether we need
to setup a polling workqueue. However, the destroy path is not balanced
and we might try to teardown an unitialized workqueue.
Balance init and destroy paths by looking at ->edac_check in both cases.
Set op_state to OP_OFFLINE *before* destroying anything.
Reported-by: Zhiqiang Hou <Zhiqiang.Hou@freescale.com>
Cc: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Hide the EDAC workqueue pointer in a separate compilation unit and add
accessors for the workqueue manipulations needed.
Remove edac_pci_reset_delay_period() which wasn't used by anything. It
seems it got added without a user with
91b99041c1 ("drivers/edac: updated PCI monitoring")
Signed-off-by: Borislav Petkov <bp@suse.de>
EDAC workqueue destruction is really fragile. We cancel delayed work
but if it is still running and requeues itself, we still go ahead and
destroy the workqueue and the queued work explodes when workqueue core
attempts to run it.
Make the destruction more robust by switching op_state to offline so
that requeuing stops. Cancel any pending work *synchronously* too.
EDAC i7core: Driver loaded.
general protection fault: 0000 [#1] SMP
CPU 12
Modules linked in:
Supported: Yes
Pid: 0, comm: kworker/0:1 Tainted: G IE 3.0.101-0-default #1 HP ProLiant DL380 G7
RIP: 0010:[<ffffffff8107dcd7>] [<ffffffff8107dcd7>] __queue_work+0x17/0x3f0
< ... regs ...>
Process kworker/0:1 (pid: 0, threadinfo ffff88019def6000, task ffff88019def4600)
Stack:
...
Call Trace:
call_timer_fn
run_timer_softirq
__do_softirq
call_softirq
do_softirq
irq_exit
smp_apic_timer_interrupt
apic_timer_interrupt
intel_idle
cpuidle_idle_call
cpu_idle
Code: ...
RIP __queue_work
RSP <...>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
The PAGES_TO_MiB macro is used for unit conversion but the
trace_mc_event() tracepoint expects a page address. Fix that.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1445341538-24271-1-git-send-email-tanxiaojun@huawei.com
Signed-off-by: Borislav Petkov <bp@suse.de>
So first of all, this atomic_scrub() function's naming is bad. It looks
like an atomic_t helper. Change it to edac_atomic_scrub().
The bigger problem is that this function is arch-specific and every new
arch which doesn't necessarily need that functionality still needs to
define it, otherwise EDAC doesn't compile.
So instead of doing that and including arch-specific headers, have each
arch define an EDAC_ATOMIC_SCRUB symbol which can be used in edac_mc.c
for ifdeffery. Much cleaner.
And we already are doing this with another symbol - EDAC_SUPPORT. This
is also much cleaner than having CONFIG_EDAC enumerate all the arches
which need/have EDAC support and drivers.
This way I can kill the useless edac.h header in tile too.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Chris Metcalf <cmetcalf@ezchip.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: "Maciej W. Rozycki" <macro@codesourcery.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Steven J. Hill" <Steven.Hill@imgtec.com>
Cc: x86@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Add edac_mc_add_mc_with_groups() for initializing the mem_ctl_info
object with the optional attribute groups. This allows drivers to
pass additional sysfs entries without manual (and racy)
device_create_file() and co calls.
edac_mc_add_mc() is kept as is, just calling edac_mc_add_with_groups()
with NULL groups.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: http://lkml.kernel.org/r/1423046938-18111-3-git-send-email-tiwai@suse.de
Signed-off-by: Borislav Petkov <bp@suse.de>
Make keeping the sync between the mem_types enum and the actual string
names simpler by using designated initializers.
Signed-off-by: Borislav Petkov <bp@suse.de>
To avoid confuision and conflict of usage for RAS related trace event,
add an unified RAS trace event stub.
Start a RAS subsystem menu which will be fleshed out in time, when more
features get added to it.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Link: http://lkml.kernel.org/r/1402475691-30045-2-git-send-email-gong.chen@linux.intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We're using edac_mc_workq_setup() both on the init path, when
we load an edac driver and when we change the polling period
(edac_mc_reset_delay_period) through /sys/.../edac_mc_poll_msec.
On that second path we don't need to init the workqueue which has been
initialized already.
Thanks to Tejun for workqueue insights.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391457913-881-1-git-send-email-prarit@redhat.com
Cc: <stable@vger.kernel.org>
Sanitize code even more to accept unsigned longs only and to not allow
polling intervals below 1 second as this is unnecessary and doesn't make
much sense anyway for polling errors.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391457913-881-1-git-send-email-prarit@redhat.com
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: <stable@vger.kernel.org>
Log messages slightly differ between edac subsystems. Unifying it.
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Robert Richter <rric@kernel.org>
Both mci.mem_is_per_rank and mci.csbased denote the same thing: the
memory controller is csrows based. Merge both fields into one.
There's no need for the driver to actually fill it, as the core detects
it by checking if one of the layers has the csrows type as part of the
memory hierarchy:
if (layers[i].type == EDAC_MC_LAYER_CHIP_SELECT)
per_rank = true;
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
The number of variables at the stack is too big.
Reduces the stack usage by using a pre-allocated error
buffer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
APEI GHES and i7core_edac/sb_edac currently can be loaded at
the same time, but those are Highlander modules:
"There can be only one".
There are two reasons for that:
1) Each driver assumes that it is the only one registering at
the EDAC core, as it is driver's responsibility to number
the memory controllers, and all of them start from 0;
2) If BIOS is handling the memory errors, the OS can't also be
doing it, as one will mangle with the other.
So, we need to add an module owner's lock at the EDAC core,
in order to avoid having two different modules handling memory
errors at the same time. The best way for doing this lock seems
to use the driver's name, as this is unique, and won't require
changes on every driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some cases where the memory controller layout is
completely hidden. This is the case of firmware-driven error
code, like the one provided by GHES. Add a new layer to be
used on such memory error report mechanisms.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRFWw4AAoJEHm+PkMAQRiGnTAH/jBHA2umNc3lc7VkUpusve4q
GGIlNzYh6iuvIGwKQVj9YPsl37qtQnkDUmY8f8WxZjfxiIDw3TkRKDgNLJaM3Jy5
E426/FGlRx/Iia5+4tuBeoVYMoIPnndgW5lEAMRK1SvhTByhIYAXsaM0UwPBetb+
Z5NMdH1f1HVF7RCCmHAkzEk9z78UpdeCzI0t0XuasP2hp2ARAcE1okdO7fNaLiyo
EmenGhRvy9bAsbRwV0rCdl0rQiZXEYM353DWS7n6q4fyVm8MXFwloUxnWCJTzOIL
ZLJaz18adFj7Ip/X6ksnMQiQU2Q3B7aThs5ycv0QGxxL2rDFveYRRQ5ICrXOy3M=
=jjBc
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc7' into next
Linux 3.8-rc7
* tag 'v3.8-rc7': (12052 commits)
Linux 3.8-rc7
net: sctp: sctp_endpoint_free: zero out secret key data
net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfree
atm/iphase: rename fregt_t -> ffreg_t
ARM: 7641/1: memory: fix broken mmap by ensuring TASK_UNMAPPED_BASE is aligned
ARM: DMA mapping: fix bad atomic test
ARM: realview: ensure that we have sufficient IRQs available
ARM: GIC: fix GIC cpumask initialization
net: usb: fix regression from FLAG_NOARP code
l2tp: dont play with skb->truesize
net: sctp: sctp_auth_key_put: use kzfree instead of kfree
netback: correct netbk_tx_err to handle wrap around.
xen/netback: free already allocated memory on failure in xen_netbk_get_requests
xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop.
xen/netback: shutdown the ring if it contains garbage.
drm/ttm: fix fence locking in ttm_buffer_object_transfer, 2nd try
virtio_console: Don't access uninitialized data.
net: qmi_wwan: add more Huawei devices, including E320
net: cdc_ncm: add another Huawei vendor specific device
ipv6/ip6_gre: fix error case handling in ip6gre_tunnel_xmit()
...
There are no more embedded kobjects in struct mem_ctl_info. Remove a header and
a comment that does not reflect the code anymore.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull EDAC fixes from Borislav Petkov:
- EDAC core error path fix, from Denis Kirjanov.
- Generalization of AMD MCE bank names and some minor error reporting
improvements.
- EDAC core cleanups and simplifications, from Wei Yongjun.
- amd64_edac fixes for sysfs-reported values, from Josh Hunt.
- some heavy amd64_edac error reporting path shaving, leading to
removing a bunch of code.
- amd64_edac error injection method improvements.
- EDAC core cleanups and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (24 commits)
EDAC, pci_sysfs: Use for_each_pci_dev to simplify the code
EDAC: Handle error path in edac_mc_sysfs_init() properly
MCE, AMD: Dump error status
MCE, AMD: Report decoded error type first
MCE, AMD: Dump CPU f/m/s triple with the error
MCE, AMD: Remove functional unit references
EDAC: Convert to use simple_open()
EDAC, Calxeda highbank: Convert to use simple_open()
EDAC: Fix mc size reported in sysfs
EDAC: Fix csrow size reported in sysfs
EDAC: Pass mci parent
EDAC: Add memory controller flags
amd64_edac: Fix csrows size and pages computation
amd64_edac: Use DBAM_DIMM macro
amd64_edac: Fix K8 chip select reporting
amd64_edac: Reorganize error reporting path
amd64_edac: Do not check whether error address is valid
amd64_edac: Improve error injection
amd64_edac: Cleanup error injection code
amd64_edac: Small fixlets and cleanups
...
A reported error could look like this
[ 226.178315] EDAC MC0: 1 CE on mc#0csrow#0channel#0 (csrow:0 channel:0 page:0x427c0d offset:0xde0 grain:0 syndrome:0x1c6)
with two spaces back-to-back due to the msg argument of
edac_mc_handle_error being passed on empty by the specific drivers.
Handle that.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The tracepoint decodes the error type later anyway so remove a useless
assignment to the temporary p which gets overwritten later anyway.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The driver is currently filling data in a wrong way, on drivers
for csrows-based memory controller, when the first layer is a
csrow.
This is not easily to notice, as, in general, memories are
filed in dual, interleaved, symetric mode, as very few memory
controllers support asymetric modes.
While digging into a bug for i82795_edac driver, the asymetric
mode there is now working, allowing us to fill the machine with
4x1GB ranks at channel 0, and 2x512GB at channel 1:
Channel 0 ranks:
EDAC DEBUG: i82975x_init_csrows: DIMM A0: from page 0x00000000 to 0x0003ffff (size: 0x00040000 pages)
EDAC DEBUG: i82975x_init_csrows: DIMM A1: from page 0x00040000 to 0x0007ffff (size: 0x00040000 pages)
EDAC DEBUG: i82975x_init_csrows: DIMM A2: from page 0x00080000 to 0x000bffff (size: 0x00040000 pages)
EDAC DEBUG: i82975x_init_csrows: DIMM A3: from page 0x000c0000 to 0x000fffff (size: 0x00040000 pages)
Channel 1 ranks:
EDAC DEBUG: i82975x_init_csrows: DIMM B0: from page 0x00100000 to 0x0011ffff (size: 0x00020000 pages)
EDAC DEBUG: i82975x_init_csrows: DIMM B1: from page 0x00120000 to 0x0013ffff (size: 0x00020000 pages)
Instead of properly showing the memories as such, before this patch, it
shows the memory layout as:
+-----------------------------------+
| mc0 |
| csrow0 | csrow1 | csrow2 |
----------+-----------------------------------+
channel1: | 1024 MB | 1024 MB | 512 MB |
channel0: | 1024 MB | 1024 MB | 512 MB |
----------+-----------------------------------+
as if both channels were symetric, grouping the DIMMs on a wrong
layout.
After this patch, the memory is correctly represented.
So, for csrows at layers[0], it shows:
+-----------------------------------------------+
| mc0 |
| csrow0 | csrow1 | csrow2 | csrow3 |
----------+-----------------------------------------------+
channel1: | 512 MB | 512 MB | 0 MB | 0 MB |
channel0: | 1024 MB | 1024 MB | 1024 MB | 1024 MB |
----------+-----------------------------------------------+
For csrows at layers[1], it shows:
+-----------------------+
| mc0 |
| channel0 | channel1 |
--------+-----------------------+
csrow3: | 1024 MB | 0 MB |
csrow2: | 1024 MB | 0 MB |
--------+-----------------------+
csrow1: | 1024 MB | 512 MB |
csrow0: | 1024 MB | 512 MB |
--------+-----------------------+
So, no matter of what comes first, the information between
channel and csrow will be properly represented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
Fix potential NULL pointer dereference in edac_unregister_sysfs() on
system boot introduced in 3.6-rc1.
Since commit 7a623c039 ("edac: rewrite the sysfs code to use struct
device") edac_mc_alloc() no longer initializes embedded kobjects in
struct mem_ctl_info. Therefore edac_mc_free() can no longer simply
decrement a kobject reference count to free the allocated memory unless
the memory controller driver module had also called edac_mc_add_mc().
Now edac_mc_free() will check if the newly embedded struct device has
been registered with sysfs before using either the standard device
release functions or freeing the data structures itself with logic
pulled out of the error path of edac_mc_alloc().
The BUG this patch resolves for me:
BUG: unable to handle kernel NULL pointer dereference at (null)
EIP is at __wake_up_common+0x1a/0x6a
Process modprobe (pid: 933, ti=f3dc6000 task=f3db9520 task.ti=f3dc6000)
Call Trace:
complete_all+0x3f/0x50
device_pm_remove+0x23/0xa2
device_del+0x34/0x142
edac_unregister_sysfs+0x3b/0x5c [edac_core]
edac_mc_free+0x29/0x2f [edac_core]
e7xxx_probe1+0x268/0x311 [e7xxx_edac]
e7xxx_init_one+0x56/0x61 [e7xxx_edac]
local_pci_probe+0x13/0x15
...
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
coccinelle warns about:
+ drivers/edac/edac_mc.c:429:9-23: ERROR: reference preceded by free on line 429
421 if (mci->csrows) {
> 422 for (chn = 0; chn < tot_channels; chn++) {
423 csr = mci->csrows[chn];
424 if (csr) {
> 425 for (chn = 0; chn < tot_channels; chn++)
426 kfree(csr->channels[chn]);
427 kfree(csr);
428 }
> 429 kfree(mci->csrows[i]);
430 }
431 kfree(mci->csrows);
432 }
and that code block seem to mess things up in several ways (double free, memory
leak, out-of-bound reads etc.):
L422: The iterator "chn" and bound "tot_channels" are totally wrong. Should be
"row" and "tot_csrows" respectively. Which means either memory leak, or
out-of-bound reads (which if does not trigger an immediate page fault
error, will further lead to kfree() on random addresses).
L425: The inner loop is reusing the same iterator "chn" as the outer loop,
which could lead to premature end of the outer loop, and hence memory leak.
L429: The array index 'i' in mci->csrows[i] is a temporary value used in
previous loops, and won't change at all in the current loop. Which
means either out-of-bound read and possibly kfree(random number), or the
same mci->csrows[i] get freed once and again, and possibly double free
for the kfree(csr) in L427.
L426/L427: a kfree(csr->channels) is needed in between to avoid leaking the memory.
The buggy code was introduced by commit de3910eb ("edac: change the mem
allocation scheme to make Documentation/kobject.txt happy") in the 3.6-rc1
merge window. Fix it by freeing up resources in this order:
free csrows[i]->channels[j]
free csrows[i]->channels
free csrows[i]
free csrows
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert delayed_work users doing cancel_delayed_work() followed by
queue_delayed_work() to mod_delayed_work().
Most conversions are straight-forward. Ones worth mentioning are,
* drivers/edac/edac_mc.c: edac_mc_workq_setup() converted to always
use mod_delayed_work() and cancel loop in
edac_mc_reset_delay_period() is dropped.
* drivers/platform/x86/thinkpad_acpi.c: No need to remember whether
watchdog is active or not. @fan_watchdog_active and related code
dropped.
* drivers/power/charger-manager.c: Seemingly a lot of
delayed_work_pending() abuse going on here.
[delayed_]work_pending() are unsynchronized and racy when used like
this. I converted one instance in fullbatt_handler(). Please
conver the rest so that it invokes workqueue APIs for the intended
target state rather than trying to game work item pending state
transitions. e.g. if timer should be modified - call
mod_delayed_work(), canceled - call cancel_delayed_work[_sync]().
* drivers/thermal/thermal_sys.c: thermal_zone_device_set_polling()
simplified. Note that round_jiffies() calls in this function are
meaningless. round_jiffies() work on absolute jiffies not delta
delay used by delayed_work.
v2: Tomi pointed out that __cancel_delayed_work() users can't be
safely converted to mod_delayed_work(). They could be calling it
from irq context and if that happens while delayed_work_timer_fn()
is running, it could deadlock. __cancel_delayed_work() users are
dropped.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Roland Dreier <roland@kernel.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
* devel: (33 commits)
edac i5000, i5400: fix pointer math in i5000_get_mc_regs()
edac: allow specifying the error count with fake_inject
edac: add support for Calxeda highbank L2 cache ecc
edac: add support for Calxeda highbank memory controller
edac: create top-level debugfs directory
sb_edac: properly handle error count
i7core_edac: properly handle error count
edac: edac_mc_handle_error(): add an error_count parameter
edac: remove arch-specific parameter for the error handler
amd64_edac: Don't pass driver name as an error parameter
edac_mc: check for allocation failure in edac_mc_alloc()
edac: Increase version to 3.0.0
edac_mc: Cleanup per-dimm_info debug messages
edac: Convert debugfX to edac_dbg(X,
edac: Use more normal debugging macro style
edac: Don't add __func__ or __FILE__ for debugf[0-9] msgs
Edac: Add ABI Documentation for the new device nodes
edac: move documentation ABI to ABI/testing/sysfs-devices-edac
i7core_edac: change the mem allocation scheme to make Documentation/kobject.txt happy
edac: change the mem allocation scheme to make Documentation/kobject.txt happy
...
In order to avoid loosing error events, it is desirable to group
error events together and generate a single trace for several identical
errors.
The trace API already allows reporting multiple errors. Change the
handle_error function to also allow that.
The changes at the drivers were made by this small script:
$file .=$_ while (<>);
$file =~ s/(edac_mc_handle_error)\s*\(([^\,]+)\,([^\,]+)\,/$1($2,$3, 1,/g;
print $file;
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the arch-dependent parameter, as it were not used,
as the MCE tracepoint weren't implemented. It probably doesn't
make sense to have an MCE-specific tracepoint, as this will
cost more bytes at the tracepoint, and tracepoint is not free.
The changes at the EDAC drivers were done by this small perl script:
$file .=$_ while (<>);
$file =~ s/(edac_mc_handle_error)\s*\(([^\;]+)\,([^\,\)]+)\s*\)/$1($2)/g;
print $file;
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a check here for if kzalloc() failed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a more common debugging style.
Remove __FILE__ uses, add missing newlines,
coalesce formats and align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The debug macro already adds that. Most of the work here was
made by this small script:
$f .=$_ while (<>);
$f =~ s/(debugf[0-9]\s*\(\s*)__FILE__\s*": /\1"/g;
$f =~ s/(debugf[0-9]\s*\(\s*)__FILE__\s*/\1/g;
$f =~ s/(debugf[0-9]\s*\(\s*)__FILE__\s*"MC: /\1"/g;
$f =~ s/(debugf[0-9]\s*\(\")\%s[\:\,\(\)]*\s*([^\"]*\s*[^\)]+)__func__\s*\,\s*/\1\2/g;
$f =~ s/(debugf[0-9]\s*\(\")\%s[\:\,\(\)]*\s*([^\"]*\s*[^\)]+),\s*__func__\s*\)/\1\2)/g;
$f =~ s/(debugf[0-9]\s*\(\"MC\:\s*)\%s[\:\,\(\)]*\s*([^\"]*\s*[^\)]+)__func__\s*\,\s*/\1\2/g;
$f =~ s/(debugf[0-9]\s*\(\"MC\:\s*)\%s[\:\,\(\)]*\s*([^\"]*\s*[^\)]+),\s*__func__\s*\)/\1\2)/g;
$f =~ s/\"MC\: \\n\"/"MC:\\n"/g;
print $f;
After running the script, manual cleanups were done to fix it the remaining
places.
While here, removed the __LINE__ on most places, as it doesn't actually give
useful info on most places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kernel kobjects have rigid rules: each container object should be
dynamically allocated, and can't be allocated into a single kmalloc.
EDAC never obeyed this rule: it has a single malloc function that
allocates all needed data into a single kzalloc.
As this is not accepted anymore, change the allocation schema of the
EDAC *_info structs to enforce this Kernel standard.
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Greg K H <gregkh@linuxfoundation.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that al users for the old kobj raw access are gone,
we can get rid of the legacy kobj-based structures and
data.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The EDAC subsystem uses the old struct sysdev approach,
creating all nodes using the raw sysfs API. This is bad,
as the API is deprecated.
As we'll be changing the EDAC API, let's first port the existing
code to struct device.
There's one drawback on this patch: driver-specific sysfs
nodes, used by mpc85xx_edac, amd64_edac and i7core_edac
won't be created anymore. While it would be possible to
also port the device-specific code, that would mix kobj with
struct device, with is not recommended. Also, it is easier and nicer
to move the code to the drivers, instead, as the core can get rid
of some complex logic that just emulates what the device_add()
and device_create_file() already does.
The next patches will convert the driver-specific code to use
the device-specific calls. Then, the remaining bits of the old
sysfs API will be removed.
NOTE: a per-MC bus is required, otherwise devices with more than
one memory controller will hit a bug like the one below:
[ 819.094946] EDAC DEBUG: find_mci_by_dev: find_mci_by_dev()
[ 819.094948] EDAC DEBUG: edac_create_sysfs_mci_device: edac_create_sysfs_mci_device() idx=1
[ 819.094952] EDAC DEBUG: edac_create_sysfs_mci_device: edac_create_sysfs_mci_device(): creating device mc1
[ 819.094967] EDAC DEBUG: edac_create_sysfs_mci_device: edac_create_sysfs_mci_device creating dimm0, located at channel 0 slot 0
[ 819.094984] ------------[ cut here ]------------
[ 819.100142] WARNING: at fs/sysfs/dir.c:481 sysfs_add_one+0xc1/0xf0()
[ 819.107282] Hardware name: S2600CP
[ 819.111078] sysfs: cannot create duplicate filename '/bus/edac/devices/dimm0'
[ 819.119062] Modules linked in: sb_edac(+) edac_core ip6table_filter ip6_tables ebtable_nat ebtables ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack ipt_REJECT xt_CHECKSUM iptable_mangle iptable_filter ip_tables bridge stp llc sunrpc binfmt_misc dm_mirror dm_region_hash dm_log vhost_net macvtap macvlan tun kvm microcode pcspkr iTCO_wdt iTCO_vendor_support igb i2c_i801 i2c_core sg ioatdma dca sr_mod cdrom sd_mod crc_t10dif ahci libahci isci libsas libata scsi_transport_sas scsi_mod wmi dm_mod [last unloaded: scsi_wait_scan]
[ 819.175748] Pid: 10902, comm: modprobe Not tainted 3.3.0-0.11.el7.v12.2.x86_64 #1
[ 819.184113] Call Trace:
[ 819.186868] [<ffffffff8105adaf>] warn_slowpath_common+0x7f/0xc0
[ 819.193573] [<ffffffff8105aea6>] warn_slowpath_fmt+0x46/0x50
[ 819.200000] [<ffffffff811f53d1>] sysfs_add_one+0xc1/0xf0
[ 819.206025] [<ffffffff811f5cf5>] sysfs_do_create_link+0x135/0x220
[ 819.212944] [<ffffffff811f7023>] ? sysfs_create_group+0x13/0x20
[ 819.219656] [<ffffffff811f5df3>] sysfs_create_link+0x13/0x20
[ 819.226109] [<ffffffff813b04f6>] bus_add_device+0xe6/0x1b0
[ 819.232350] [<ffffffff813ae7cb>] device_add+0x2db/0x460
[ 819.238300] [<ffffffffa0325634>] edac_create_dimm_object+0x84/0xf0 [edac_core]
[ 819.246460] [<ffffffffa0325e18>] edac_create_sysfs_mci_device+0xe8/0x290 [edac_core]
[ 819.255215] [<ffffffffa0322e2a>] edac_mc_add_mc+0x5a/0x2c0 [edac_core]
[ 819.262611] [<ffffffffa03412df>] sbridge_register_mci+0x1bc/0x279 [sb_edac]
[ 819.270493] [<ffffffffa03417a3>] sbridge_probe+0xef/0x175 [sb_edac]
[ 819.277630] [<ffffffff813ba4e8>] ? pm_runtime_enable+0x58/0x90
[ 819.284268] [<ffffffff812f430c>] local_pci_probe+0x5c/0xd0
[ 819.290508] [<ffffffff812f5ba1>] __pci_device_probe+0xf1/0x100
[ 819.297117] [<ffffffff812f5bea>] pci_device_probe+0x3a/0x60
[ 819.303457] [<ffffffff813b1003>] really_probe+0x73/0x270
[ 819.309496] [<ffffffff813b138e>] driver_probe_device+0x4e/0xb0
[ 819.316104] [<ffffffff813b149b>] __driver_attach+0xab/0xb0
[ 819.322337] [<ffffffff813b13f0>] ? driver_probe_device+0xb0/0xb0
[ 819.329151] [<ffffffff813af5d6>] bus_for_each_dev+0x56/0x90
[ 819.335489] [<ffffffff813b0d7e>] driver_attach+0x1e/0x20
[ 819.341534] [<ffffffff813b0980>] bus_add_driver+0x1b0/0x2a0
[ 819.347884] [<ffffffffa0347000>] ? 0xffffffffa0346fff
[ 819.353641] [<ffffffff813b19f6>] driver_register+0x76/0x140
[ 819.359980] [<ffffffff8159f18b>] ? printk+0x51/0x53
[ 819.365524] [<ffffffffa0347000>] ? 0xffffffffa0346fff
[ 819.371291] [<ffffffff812f5896>] __pci_register_driver+0x56/0xd0
[ 819.378096] [<ffffffffa0347054>] sbridge_init+0x54/0x1000 [sb_edac]
[ 819.385231] [<ffffffff8100203f>] do_one_initcall+0x3f/0x170
[ 819.391577] [<ffffffff810bcd2e>] sys_init_module+0xbe/0x230
[ 819.397926] [<ffffffff815bb529>] system_call_fastpath+0x16/0x1b
[ 819.404633] ---[ end trace 1654fdd39556689f ]---
This happens because the bus is not being properly initialized.
Instead of putting the memory sub-devices inside the memory controller,
it is putting everything under the same directory:
$ tree /sys/bus/edac/
/sys/bus/edac/
├── devices
│ ├── all_channel_counts -> ../../../devices/system/edac/mc/mc0/all_channel_counts
│ ├── csrow0 -> ../../../devices/system/edac/mc/mc0/csrow0
│ ├── csrow1 -> ../../../devices/system/edac/mc/mc0/csrow1
│ ├── csrow2 -> ../../../devices/system/edac/mc/mc0/csrow2
│ ├── dimm0 -> ../../../devices/system/edac/mc/mc0/dimm0
│ ├── dimm1 -> ../../../devices/system/edac/mc/mc0/dimm1
│ ├── dimm3 -> ../../../devices/system/edac/mc/mc0/dimm3
│ ├── dimm6 -> ../../../devices/system/edac/mc/mc0/dimm6
│ ├── inject_addrmatch -> ../../../devices/system/edac/mc/mc0/inject_addrmatch
│ ├── mc -> ../../../devices/system/edac/mc
│ └── mc0 -> ../../../devices/system/edac/mc/mc0
├── drivers
├── drivers_autoprobe
├── drivers_probe
└── uevent
On a multi-memory controller system, the names "csrow%d" and "dimm%d"
should be under "mc%d", and not at the main hierarchy level.
So, we need to create a per-MC bus, in order to have its own namespace.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Greg K H <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic was checking the sizeof the structure being allocated to
determine whether an alignment fixup was required. This isn't right;
what we actually care about is the alignment of the actual pointer that's
about to be returned. This became an issue recently because struct
edac_mc_layer has a size that is not zero modulo eight, so we were
taking the correctly-aligned pointer and forcing it to be misaligned.
On Tile this caused an alignment exception.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As EDAC doesn't use struct device itself, it created a parent dev
pointer called as "pdev". Now that we'll be converting it to use
struct device, instead of struct devsys, this needs to be fixed.
No functional changes.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new tracepoint-based hardware events report method for
reporting Memory Controller events.
Part of the description bellow is shamelessly copied from Tony
Luck's notes about the Hardware Error BoF during LPC 2010 [1].
Tony, thanks for your notes and discussions to generate the
h/w error reporting requirements.
[1] http://lwn.net/Articles/416669/
We have several subsystems & methods for reporting hardware errors:
1) EDAC ("Error Detection and Correction"). In its original form
this consisted of a platform specific driver that read topology
information and error counts from chipset registers and reported
the results via a sysfs interface.
2) mcelog - x86 specific decoding of machine check bank registers
reporting in binary form via /dev/mcelog. Recent additions make use
of the APEI extensions that were documented in version 4.0a of the
ACPI specification to acquire more information about errors without
having to rely reading chipset registers directly. A user level
programs decodes into somewhat human readable format.
3) drivers/edac/mce_amd.c - this driver hooks into the mcelog path and
decodes errors reported via machine check bank registers in AMD
processors to the console log using printk();
Each of these mechanisms has a band of followers ... and none
of them appear to meet all the needs of all users.
As part of a RAS subsystem, let's encapsulate the memory error hardware
events into a trace facility.
The tracepoint printk will be displayed like:
mc_event: [quant] (Corrected|Uncorrected|Fatal) error:[error msg] on [label] ([location] [edac_mc detail] [driver_detail]
Where:
[quant] is the quantity of errors
[error msg] is the driver-specific error message
(e. g. "memory read", "bus error", ...);
[location] is the location in terms of memory controller and
branch/channel/slot, channel/slot or csrow/channel;
[label] is the memory stick label;
[edac_mc detail] describes the address location of the error
and the syndrome;
[driver detail] is driver-specifig error message details,
when needed/provided (e. g. "area:DMA", ...)
For example:
mc_event: 1 Corrected error:memory read on memory stick DIMM_1A (mc:0 location:0:0:0 page:0x586b6e offset:0xa66 grain:32 syndrome:0x0 area:DMA)
Of course, any userspace tools meant to handle errors should not parse
the above data. They should, instead, use the binary fields provided by
the tracepoint, mapping them directly into their Management Information
Base.
NOTE: The original patch was providing an additional mechanism for
MCA-based trace events that also contained MCA error register data.
However, as no agreement was reached so far for the MCA-based trace
events, for now, let's add events only for memory errors.
A latter patch is planned to change the tracepoint, for those types
of event.
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While userspace doesn't fill the dimm labels, add there the dimm location,
as described by the used memory model. This could eventually match what
is described at the dmidecode, making easier for people to identify the
memory.
For example, on an Intel motherboard where the DMI table is reliable,
the first memory stick is described as:
Memory Device
Array Handle: 0x0029
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 1
Locator: A1_DIMM0
Bank Locator: A1_Node0_Channel0_Dimm0
Type: <OUT OF SPEC>
Type Detail: Synchronous
Speed: 800 MHz
Manufacturer: A1_Manufacturer0
Serial Number: A1_SerNum0
Asset Tag: A1_AssetTagNum0
Part Number: A1_PartNum0
The memory named as "A1_DIMM0" is physically located at the first
memory controller (node 0), at channel 0, dimm slot 0.
After this patch, the memory label will be filled with:
/sys/devices/system/edac/mc/csrow0/ch0_dimm_label:mc#0channel#0slot#0
And (after the new EDAC API patches) as:
/sys/devices/system/edac/mc/mc0/dimm0/dimm_label:mc#0channel#0slot#0
So, even if the memory label is not initialized on userspace, an useful
information with the error location is filled there, expecially since
several systems/motherboards are provided with enough info to map from
channel/slot (or branch/channel/slot) into the DIMM label. So, letting the
EDAC core fill it by default is a good thing.
It should noticed that, as the label filling happens at the
edac_mc_alloc(), drivers can override it to better describe the memories
(and some actually do it).
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that all drivers got converted to use the new ABI, we can
drop the old one.
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the EDAC internal representation to work with non-csrow
based memory controllers.
There are lots of those memory controllers nowadays, and more
are coming. So, the EDAC internal representation needs to be
changed, in order to work with those memory controllers, while
preserving backward compatibility with the old ones.
The edac core was written with the idea that memory controllers
are able to directly access csrows.
This is not true for FB-DIMM and RAMBUS memory controllers.
Also, some recent advanced memory controllers don't present a per-csrows
view. Instead, they view memories as DIMMs, instead of ranks.
So, change the allocation and error report routines to allow
them to work with all types of architectures.
This will allow the removal of several hacks with FB-DIMM and RAMBUS
memory controllers.
Also, several tests were done on different platforms using different
x86 drivers.
TODO: a multi-rank DIMMs are currently represented by multiple DIMM
entries in struct dimm_info. That means that changing a label for one
rank won't change the same label for the other ranks at the same DIMM.
This bug is present since the beginning of the EDAC, so it is not a big
deal. However, on several drivers, it is possible to fix this issue, but
it should be a per-driver fix, as the csrow => DIMM arrangement may not
be equal for all. So, don't try to fix it here yet.
I tried to make this patch as short as possible, preceding it with
several other patches that simplified the logic here. Yet, as the
internal API changes, all drivers need changes. The changes are
generally bigger in the drivers for FB-DIMMs.
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The edac_align_ptr() function is used to prepare data for a single
memory allocation kzalloc() call. It counts how many bytes are needed
by some data structure.
Using it as-is is not that trivial, as the quantity of memory elements
reserved is not there, but, instead, it is on a next call.
In order to avoid mistakes when using it, move the number of allocated
elements into it, making easier to use it.
Reviewed-by: Borislav Petkov <bp@amd64.org>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The number of pages is a dimm property. Move it to the dimm struct.
After this change, it is possible to add sysfs nodes for the DIMM's that
will properly represent the DIMM stick properties, including its size.
A TODO fix here is to properly represent dual-rank/quad-rank DIMMs when
the memory controller represents the memory via chip select rows.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On systems based on chip select rows, all channels need to use memories
with the same properties, otherwise the memories on channels A and B
won't be recognized.
However, such assumption is not true for all types of memory
controllers.
Controllers for FB-DIMM's don't have such requirements.
Also, modern Intel controllers seem to be capable of handling such
differences.
So, we need to get rid of storing the DIMM information into a per-csrow
data, storing it, instead at the right place.
The first step is to move grain, mtype, dtype and edac_mode to the
per-dimm struct.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Mike Williams <mike@mikebwilliams.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The way a DIMM is currently represented implies that they're
linked into a per-csrow struct. However, some drivers don't see
csrows, as they're ridden behind some chip like the AMB's
on FBDIMM's, for example.
This forced drivers to fake^Wvirtualize a csrow struct, and to create
a mess under csrow/channel original's concept.
Move the DIMM labels into a per-DIMM struct, and add there
the real location of the socket, in terms of csrow/channel.
Latter patches will modify the location to properly represent the
memory architecture.
All other drivers will use a per-csrow type of location.
Some of those drivers will require a latter conversion, as
they also fake the csrows internally.
TODO: While this patch doesn't change the existing behavior, on
csrows-based memory controllers, a csrow/channel pair points to a memory
rank. There's a known bug at the EDAC core that allows having different
labels for the same DIMM, if it has more than one rank. A latter patch
is need to merge the several ranks for a DIMM into the same dimm_info
struct, in order to avoid having different labels for the same DIMM.
The edac_mc_alloc() will now contain a per-dimm initialization loop that
will be changed by latter patches in order to match other types of
memory architectures.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull EDAC fixes from Mauro Carvalho Chehab:
"A series of EDAC driver fixes. It also has one core fix at the
documentation, and a rename patch, fixing the name of the struct that
contains the rank information."
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
edac: rename channel_info to rank_info
i5400_edac: Avoid calling pci_put_device() twice
edac: i5100 ack error detection register after each read
edac: i5100 fix erroneous define for M1Err
edac: sb_edac: Fix a wrong value setting for the previous value
edac: sb_edac: Fix a INTERLEAVE_MODE() misuse
edac: sb_edac: Let the driver depend on PCI_MMCONFIG
edac: Improve the comments to better describe the memory concepts
edac/ppc4xx_edac: Fix compilation
Fix sb_edac compilation with 32 bits kernels
What it is pointed by a csrow/channel vector is a rank information, and
not a channel information.
On a traditional architecture, the memory controller directly access the
memory ranks, via chip select rows. Different ranks at the same DIMM is
selected via different chip select rows. So, typically, one
csrow/channel pair means one different DIMM.
On FB-DIMMs, there's a microcontroller chip at the DIMM, called Advanced
Memory Buffer (AMB) that serves as the interface between the memory
controller and the memory chips.
The AMB selection is via the DIMM slot, and not via a csrow.
It is up to the AMB to talk with the csrows of the DRAM chips.
So, the FB-DIMM memory controllers see the DIMM slot, and not the DIMM
rank. RAMBUS is similar.
Newer memory controllers, like the ones found on Intel Sandy Bridge and
Nehalem, even working with normal DDR3 DIMM's, don't use the usual
channel A/channel B interleaving schema to provide 128 bits data access.
Instead, they have more channels (3 or 4 channels), and they can use
several interleaving schemas. Such memory controllers see the DIMMs
directly on their registers, instead of the ranks, which is better for
the driver, as its main usageis to point to a broken DIMM stick (the
Field Repleceable Unit), and not to point to a broken DRAM chip.
The drivers that support such such newer memory architecture models
currently need to fake information and to abuse on EDAC structures, as
the subsystem was conceived with the idea that the csrow would always be
visible by the CPU.
To make things a little worse, those drivers don't currently fake
csrows/channels on a consistent way, as the concepts there don't apply
to the memory controllers they're talking with. So, each driver author
interpreted the concepts using a different logic.
In order to fix it, let's rename the data structure that points into a
DIMM rank to "rank_info", in order to be clearer about what's stored
there.
Latter patches will provide a better way to represent the memory
hierarchy for the other types of memory controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a macro per printk level, shorten up error messages. Add relevant
information to KERN_INFO level. No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
00740c5854 changed edac_core to
un-/register a workqueue item only if a lowlevel driver supplies a
polling routine. Normally, when we remove a polling low-level driver, we
go and cancel all the queued work. However, the workqueue unreg happens
based on the ->op_state setting, and edac_mc_del_mc() sets this to
OP_OFFLINE _before_ we cancel the work item, leading to NULL ptr oops on
the workqueue list.
Fix it by putting the unreg stuff in proper order.
Cc: <stable@kernel.org> #36.x
Reported-and-tested-by: Tobias Karnat <tobias.karnat@googlemail.com>
LKML-Reference: <1291201307.3029.21.camel@Tobias-Karnat>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This is a nasty bug. Since kobject count will be reduced by zero by
edac_mc_del_mc(), and this triggers the kobj release method, the
mci memory will be freed automatically. So, all we have left is ctl_name,
as shown by enabling debug:
[ 80.822186] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 1020: edac_remove_sysfs_mci_device() remove_link
[ 80.832590] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 1024: edac_remove_sysfs_mci_device() remove_mci_instance
[ 80.843776] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 640: edac_mci_control_release() mci instance idx=0 releasing
[ 80.855163] EDAC MC: Removed device 0 for i7core_edac.c i7 core #0: DEV 0000:3f:03.0
[ 80.862936] EDAC DEBUG: in drivers/edac/i7core_edac.c, line at 2089: (null): free structs
[ 80.871134] EDAC DEBUG: in drivers/edac/edac_mc.c, line at 238: edac_mc_free()
[ 80.878379] EDAC DEBUG: in drivers/edac/edac_mc_sysfs.c, line at 726: edac_mc_unregister_sysfs_main_kobj()
[ 80.888043] EDAC DEBUG: in drivers/edac/i7core_edac.c, line at 1232: drivers/edac/i7core_edac.c: i7core_put_devices()
Also, kfree(mci) shouldn't happen at the kobj.release, as it happens
when edac_remove_sysfs_mci_device() is called, but the logic is:
edac_remove_sysfs_mci_device(mci);
edac_printk(KERN_INFO, EDAC_MC,
"Removed device %d for %s %s: DEV %s\n", mci->mc_idx,
mci->mod_name, mci->ctl_name, edac_dev_name(mci));
So, as the edac_printk() needs the mci struct, this generates an OOPS.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With multi-sockets, more than one edac pci handler is enabled. Be sure to
un-register all instances.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
f4347553b3 removed the edac polling
mechanism in favor of using a notifier chain for conveying MCE
information to edac. However, the module removal path didn't test
whether the driver had setup the polling function workqueue at all and
the rmmod process was hanging in the kernel at try_to_del_timer_sync()
in the cancel_delayed_work() path, trying to cancel an uninitialized
work struct.
Fix that by adding a balancing check to the workqueue removal path.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Instead of using deeply-nested conditionals for dumping the DIMM type in
debug mode, add a strings array of the supported DIMM types.
This is useful in cases where an edac driver supports multiple DRAM
types and is only defined in debug builds.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Module edac_core.ko uses call_rcu() callbacks in edac_device.c, edac_mc.c
and edac_pci.c.
They all use a wait_for_completion() scheme, but this scheme it not 100%
safe on multiple CPUs. See the _rcu_barrier() implementation which
explains why extra precausion is needed.
The patch adds a comment about rcu_barrier() and as a precausion calls
rcu_barrier(). A maintainer needs to look at removing the
wait_for_completion code.
[dougthompson@xmission.com: remove the wait_for_completion code]
Signed-off-by Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The edac-core driver includes code which assumes that the work_struct
which is included in every delayed_work is the first member of that
structure. This is currently the case but might change in the future, so
use to_delayed_work() instead, which doesn't make such an assumption.
linux-2.6.30-rc1 has the to_delayed_work() function that will allow this
patch to work
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is part of a larger patch series which will remove the "char
bus_id[20]" name string from struct device. The device name is managed in
the kobject anyway, and without any size limitation, and just needlessly
copied into "struct device".
[akpm@linux-foundation.org: coding-style fixes]
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 06916639e2 ("driver-core: add
dev_name() to help transition away from using bus_id") added a static
inline dev_name() and used it in dev_printk.
Unfortunately, drivers/edac/edac_core.h defines a macro called
dev_name(). Rename the latter.
Diagnosis by Tony Breeds and Michael Ellerman.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Collection of patches, merged into one, from Adrian that do the following:
1) This patch makes the following needlessly global functions static:
- edac_pci_get_log_pe()
- edac_pci_get_log_npe()
- edac_pci_get_panic_on_pe()
- edac_pci_unregister_sysfs_instance_kobj()
- edac_pci_main_kobj_setup()
2) Remove unneeded function edac_device_find()
3) Added #if 0 around function edac_pci_find()
4) make the needlessly global edac_pci_generic_check() static
5) Removed function edac_check_mc_devices()
Doug Thompson modified Adrian's patches, to bettern represent
the direction of EDAC, and make them one patch.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a deadlock that could occur on a 'setup' and 'teardown' sequence of
the workq for a edac_mc control structure instance. A similiar fix was
previously implemented for the edac_device code.
In addition, the edac_mc device code there was missing code to allow the workq
period valu to be altered via sysfs control.
This patch adds that fix on the code, and allows for the changing of the
period value as well.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mutex locking deadlock on the device controller linked list. Was calling
a lock then a function that could call the same lock. Moved the cancel workq
function to outside the lock
Added some short circuit logic in the workq code
Added comments of description
Code tidying
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch refactors the 'releasing' of kobjects for the edac_mc type of
device. The correct pattern of kobject release is followed.
As internal kobjs are allocated they bump a ref count on the top level kobj.
It in turn has a module ref count on the edac_core module. When internal
kobjects are released, they dec the ref count on the top level kobj. When the
top level kobj reaches zero, it decrements the ref count on the edac_core
object, allow it to be unloaded, as all resources have all now been released.
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactoring of sysfs code necessitated the refactoring of the edac_mc_alloc()
and edac_mc_add_mc() apis, of moving the index value to the alloc() function.
This patch alters the in tree drivers to utilize this new api signature.
Having the index value performed later created a chicken-and-the-egg issue.
Moving it to the alloc() function allows for creating the necessary sysfs
entries with the proper index number
Cc: Alan Cox alan@lxorguk.ukuu.org.uk
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactor the edac_align_ptr() function to reduce the noise of casting the
aligned pointer to the various types of data objects and modified its callers
to its new signature
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes some remnant spaces inserted by the use of Lindent.
Seems Lindent adds some spaces when it shoulded. These have been fixed.
In addition, goto targets have issues, these have been fixed
in this patch.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The origin of this code comes from patches at sourceforge, that
allow EDAC to be updated to various kernels. With kernel version 2.6.20 a
new workq system was installed, thus the patches needed to be modified
based on the kernel version. For submitting to the latest kernel.org
those #ifdefs are removed
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Run the EDAC CORE files through Lindent for cleanup
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup poll values for MC and PCI.
Also make mc function names unique to mc.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmissin.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change error check and clear variable from an atomic to an int
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the memory controller object to work queue based implementation from the
kernel thread based.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move dev_name() macro to a more generic interface since it's not possible
to determine whether a device is pci, platform, or of_device easily.
Now each low level driver sets the name into the control structure, and
the EDAC core references the control structure for the information.
Better abstraction.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the refactoring of edac_mc.c into several subsystem files,
the header file edac_mc.h became meaningless. A new header file
edac_core.h was created. All the files that previously included
"edac_mc.h" are changed to include "edac_core.h".
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provides a way for NMI reported errors on x86 to notify the EDAC
subsystem pending ECC errors by writing to a software state variable.
Here's the reworked patch. I added an EDAC stub to the kernel so we can
have variables that are in the kernel even if EDAC is a module. I also
implemented the idea of using the chip driver to select error detection
mode via module parameter and eliminate the kernel compile option.
Please review/test. Thx!
Also, I only made changes to some of the chipset drivers since I am
unfamiliar with the other ones. We can add similar changes as we go.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The EDAC core code uses a semaphore as mutex. use the mutex API
instead of the (binary) semaphore.
Matthaias wrote this, but since I had some patches ahead of it,
I need to modify it to follow my patches.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the new 'class' of object to be managed, named: 'edac_device'.
As a peer of the 'edac_mc' class of object, it provides a non-memory centric
view of an ERROR DETECTING device in hardware. It provides a sysfs interface
and an abstraction for varioius EDAC type devices.
Multiple 'instances' within the class are possible, with each 'instance'
able to have multiple 'blocks', and each 'block' having 'attributes'.
At the 'block' level there are the 'ce_count' and 'ue_count' fields
which the device driver can update and/or call edac_device_handle_XX()
functions. At each higher level are additional 'total' count fields,
which are a summation of counts below that level.
This 'edac_device' has been used to capture and present ECC errors
which are found in a a L1 and L2 system on a per CORE/CPU basis.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a large patch to refactor the original EDAC module in the kernel
and to break it up into better file granularity, such that each source
file contains a given subsystem of the EDAC CORE.
Originally, the EDAC 'core' was contained in one source file: edac_mc.c
with it corresponding edac_mc.h file.
Now, there are the following files:
edac_module.c The main module init/exit function and other overhead
edac_mc.c Code handling the edac_mc class of object
edac_mc_sysfs.c Code handling for sysfs presentation
edac_pci_sysfs.c Code handling for PCI sysfs presentation
edac_core.h CORE .h include file for 'edac_mc' and 'edac_device' drivers
edac_module.h Internal CORE .h include file
This forms a foundation upon which a later patch can create the 'edac_device'
class of object code in a new file 'edac_device.c'.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes needlessly global code static, in the edac core
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This simple patch adds an important CORE API for EDAC that EDAC drivers can
use to find their edac_mc control structure by passing a mem_ctl_info
'instance' value
Needed for subsequent patches
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Wollesen ported the Bluesmoke Memory Controller driver for the Intel
5000X/V/P (Blackford/Greencreek) chipset to the in kernel EDAC model.
This patch incorporates those required changes to the edac_mc.c and edac_mc.h
core files by added new Fully Buffered DIMM interface to the EDAC Core module.
Signed-off-by: eric wollesen <ericw@xmtp.net>
Signed-off-by: doug thompson <norsk5@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an attempt of providing an interface for memory scrubbing control in
EDAC.
This patch modifies the EDAC Core to provide the Interface for memory
controller modules to implment.
The following things are still outstanding:
- K8 is the first implemenation,
The patch provide a method of configuring the K8 hardware memory scrubber
via the 'mcX' sysfs directory. There should be some fallback to a generic
scrubber implemented in software if the hardware does not support
scrubbing.
Or .. the scrubbing sysfs entry should not be visible at all.
- Only works with SDRAM, not cache,
The K8 can scrub cache and l2cache also - but I think this is not so
useful as the cache is busy all the time (one hopes).
One would also expect that cache scrubbing requires hardware support.
- Error Handling,
I would like that errors are returned to the user in "terms of file
system".
- Presentation,
I chose Bandwidth in Bytes/Second as a representation of the scrubbing
rate for the following reasons:
I like that the sysfs entries are sort-of textual, related to something
that makes sense instead of magical values that must be looked up.
"My People" wants "% main memory scrubbed per hour" others prefer "%
memory bandwidth used" as representation, "bandwith used" makes it easy to
calculate both versions in one-liner scripts.
If one later wants to scrub cache, the scaling becomes wierd for K8
changing from "blocks of 64 byte memory" to "blocks of 64 cache lines" to
"blocks of 64 bit". Using "bandwidth used" makes sense in all three cases,
(I.M.O. anyway ;-).
- Discovery,
There is no way to discover the possible settings and what they do
without reading the code and the documentation.
*I* do not know how to make that work in a practical way.
- Bugs(??),
other tools can set invalid values in the memory scrub control register,
those will read back as '-1', requiring the user to reset the scrub rate.
This is how *I* think it should be.
- Afflicting other areas of code,
I made changes to edac_mc.c and edac_mc.h which will show up globally -
this is not nice, it would be better that the memory scrubbing fuctionality
and interface could be entirely contained within the memory controller it
applies to.
Frithiof Jensen
edac_mc.c and its .h file is a CORE helper module for EDAC
driver modules. This provides the abstraction for device specific
drivers. It is fine to modify this CORE to provide help for
new features of the the drivers
doug thompson
Signed-off-by: Frithiof Jensen <frithiof.jensen@ericson.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mauro Carvalho Chehab