This patch fixed following Warning while executing "make htmldocs".
Warning(/net/core/skbuff.c:2164): No description found for parameter 'from'
Warning(/net/core/skbuff.c:2164): Excess function parameter 'source'
description in 'skb_zerocopy'
Replace "@source" with "@from" fixed the warning.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves part of Eric Dumazets skb_gso_seglen helper from tbf sched to
skbuff core so it may be reused by upcoming ip forwarding path patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This check is not needed because the same check is done before
fill_slave_info is used in rtnl_link_slave_info_fill.
Also, by removing this check, kernel will fillup IFLA_INFO_SLAVE_KIND
even for slaves of masters which does not implement fill_slave_info.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have multiple devices attempting to sync the same address
to a single destination, each device should be permitted to sync
it once. To accomplish this, pass the 'sync_cnt' of the source
address when adding the addresss to the lower device. 'sync_cnt'
tracks how many time a given address has been succefully synced.
This way, we know that if the 'sync_cnt' passed in is 0, we should
sync this address.
Also, turn 'synced' member back into the counter as was originally
done in
commit 4543fbefe6.
net: count hw_addr syncs so that unsync works properly.
It tracks how many time a given address has been added via a
'sync' operation. For every successfull 'sync' the counter is
incremented, and for ever 'unsync', the counter is decremented.
This makes sure that the address will be properly removed from
the the lower device when all the upper devices have removed it.
Reported-by: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
CC: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
CC: Alexandra N. Kossovsky <Alexandra.Kossovsky@oktetlabs.ru>
CC: Konstantin Ushakov <Konstantin.Ushakov@oktetlabs.ru>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fuse update from Miklos Szeredi:
"This contains a fix for a potential use-after-module-unload bug
noticed by Al and caching improvements for read-only fuse filesystems
by Andrew Gallagher"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: support clients that don't implement 'open'
fuse: don't invalidate attrs when not using atime
fuse: fix SetPageUptodate() condition in STORE
fuse: fix pipe_buf_operations
Recent patch
bonding: add netlink attributes to slave link dev (1d3ee88ae0)
Introduced yet another device specific way to access slave information
over rtnetlink. There is one already there for bridge.
This patch introduces generic way to do this, for getting and setting
info as well by extending link_ops. Later on, this new interface will
be used for bridge ports as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Workqueue used in neighbour layer have no real dependency of scheduling these on
the cpu which scheduled them.
On a idle system, it is observed that an idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.
This patch replaces normal workqueues with power efficient versions. This
doesn't change existing behavior of code unless CONFIG_WQ_POWER_EFFICIENT is
enabled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
Having this struct in module memory could Oops when if the module is
unloaded while the buffer still persists in a pipe.
Since sock_pipe_buf_ops is essentially the same as fuse_dev_pipe_buf_steal
merge them into nosteal_pipe_buf_ops (this is the same as
default_pipe_buf_ops except stealing the page from the buffer is not
allowed).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the gro_find_receive/complete_by_type helpers to they can be invoked
by the gro callbacks of encapsulation protocols such as vxlan.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add GRO handlers for protocols that do UDP encapsulation, with the intent of
being able to coalesce packets which encapsulate packets belonging to
the same TCP session.
For GRO purposes, the destination UDP port takes the role of the ether type
field in the ethernet header or the next protocol in the IP header.
The UDP GRO handler will only attempt to coalesce packets whose destination
port is registered to have gro handler.
Use a mark on the skb GRO CB data to disallow (flush) running the udp gro receive
code twice on a packet. This solves the problem of udp encapsulated packets whose
inner VM packet is udp and happen to carry a port which has registered offloads.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup updates from Tejun Heo:
"The bulk of changes are cleanups and preparations for the upcoming
kernfs conversion.
- cgroup_event mechanism which is and will be used only by memcg is
moved to memcg.
- pidlist handling is updated so that it can be served by seq_file.
Also, the list is not sorted if sane_behavior. cgroup
documentation explicitly states that the file is not sorted but it
has been for quite some time.
- All cgroup file handling now happens on top of seq_file. This is
to prepare for kernfs conversion. In addition, all operations are
restructured so that they map 1-1 to kernfs operations.
- Other cleanups and low-pri fixes"
* 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (40 commits)
cgroup: trivial style updates
cgroup: remove stray references to css_id
doc: cgroups: Fix typo in doc/cgroups
cgroup: fix fail path in cgroup_load_subsys()
cgroup: fix missing unlock on error in cgroup_load_subsys()
cgroup: remove for_each_root_subsys()
cgroup: implement for_each_css()
cgroup: factor out cgroup_subsys_state creation into create_css()
cgroup: combine css handling loops in cgroup_create()
cgroup: reorder operations in cgroup_create()
cgroup: make for_each_subsys() useable under cgroup_root_mutex
cgroup: css iterations and css_from_dir() are safe under cgroup_mutex
cgroup: unify pidlist and other file handling
cgroup: replace cftype->read_seq_string() with cftype->seq_show()
cgroup: attach cgroup_open_file to all cgroup files
cgroup: generalize cgroup_pidlist_open_file
cgroup: unify read path so that seq_file is always used
cgroup: unify cgroup_write_X64() and cgroup_write_string()
cgroup: remove cftype->read(), ->read_map() and ->write()
hugetlb_cgroup: convert away from cftype->read()
...
softnet_data is already set to 0, no need to use memset or initialize
specific fields to 0 or NULL afterwards.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I create a new namespace with 'ip netns add net0', or add/remove
new links in a namespace with 'ip link add/delete type veth', rx/tx
queues events can be got in all namespaces. That is because rx/tx queue
ktypes do not have namespace support, and their kobj parents are setted to
NULL. This patch is to fix it.
Reported-by: Libo Chen <chenlibo@huawei.com>
Signed-off-by: Libo Chen <chenlibo@huawei.com>
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To silent "make htmldocs" warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For user space packet capturing libraries such as libpcap, there's
currently only one way to check which BPF extensions are supported
by the kernel, that is, commit aa1113d9f8 ("net: filter: return
-EINVAL if BPF_S_ANC* operation is not supported"). For querying all
extensions at once this might be rather inconvenient.
Therefore, this patch introduces a new option which can be used as
an argument for getsockopt(), and allows one to obtain information
about which BPF extensions are supported by the current kernel.
As David Miller suggests, we do not need to define any bits right
now and status quo can just return 0 in order to state that this
versions supports SKF_AD_PROTOCOL up to SKF_AD_PAY_OFFSET. Later
additions to BPF extensions need to add their bits to the
bpf_tell_extensions() function, as documented in the comment.
Signed-off-by: Michal Sekletar <msekleta@redhat.com>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
If link is IFF_SLAVE, extend link dev netlink attributes to include
slave attributes with new IFLA_SLAVE nest. Add netlink notification
(RTM_NEWLINK) when slave status changes from backup to active, or
visa-versa.
Adds new ndo_get_slave op to net_device_ops to fill skb with IFLA_SLAVE
attributes. Currently only used by bonding driver, but could be
used by other aggregating devices with slaves.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing support for netdevice receive queue sysfs attributes to
permit a device-specific attribute group. Initial use case for this
support will be to allow the virtio-net device to export per-receive
queue mergeable receive buffer size.
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_page_frag_refill currently permits only order-0 page allocs
unless GFP_WAIT is used. Change skb_page_frag_refill to attempt
higher-order page allocations whether or not GFP_WAIT is used. If
memory cannot be allocated, the allocator will fall back to
successively smaller page allocs (down to order-0 page allocs).
This change brings skb_page_frag_refill in line with the existing
page allocation strategy employed by netdev_alloc_frag, which attempts
higher-order page allocations whether or not GFP_WAIT is set, falling
back to successively lower-order page allocations on failure. Part
of migration of virtio-net to per-receive queue page frag allocators.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a device changes its mtu, first the change happens (invloving
all the side effects), and after that the NETDEV_CHANGEMTU is sent so that
other devices can catch up with the new mtu. However, if they return
NOTIFY_BAD, then the change is reverted and error returned.
This is a really long and costy operation (sometimes). To fix this, add
NETDEV_PRECHANGEMTU notification which is called prior to any change
actually happening, and if any callee returns NOTIFY_BAD - the change is
aborted. This way we're skipping all the playing with apply/revert the mtu.
CC: "David S. Miller" <davem@davemloft.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing a gro_list for a packet, first check the rxhash of
the incoming skb against that of the skb's in the list. This should be
a very strong inidicator of whether the flow is going to be matched,
and potentially allows a lot of other checks to be short circuited.
Use skb_hash_raw so that we don't force the hash to be calculated.
Tested by running netperf 200 TCP_STREAMs between two machines with
GRO, HW rxhash, and 1G. Saw no performance degration, slight reduction
of time in dev_gro_receive.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At first Jakub Zawadzki noticed that some divisions by reciprocal_divide
were not correct. (off by one in some cases)
http://www.wireshark.org/~darkjames/reciprocal-buggy.c
He could also show this with BPF:
http://www.wireshark.org/~darkjames/set-and-dump-filter-k-bug.c
The reciprocal divide in linux kernel is not generic enough,
lets remove its use in BPF, as it is not worth the pain with
current cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Daniel Borkmann <dxchgb@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we don't rename the upper/lower_ifc symlinks in
/sys/class/net/*/ , which might result stale/duplicate links/names.
Fix this by adding netdev_adjacent_rename_links(dev, oldname) which renames
all the upper/lower interface's links to dev from the upper/lower_oldname
to the new name.
We don't need a rollback because only we control these symlinks and if we
fail to rename them - sysfs will anyway complain.
Reported-by: Ding Tianhong <dingtianhong@huawei.com>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They clean up the code a bit and can be used further.
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduced by:
commit 1f9248e560
"neigh: convert parms to an array"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the net_random and net_srandom macros and replaces
them with direct calls to the prandom ones. As new commits only seem to
use prandom_u32 there is no use to keep them around.
This change makes it easier to grep for users of prandom_u32.
Signed-off-by: Aruna-Hewapathirane <aruna.hewapathirane@gmail.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing net/netif_rx and net/netif_receive_skb trace events
provide little information about the skb, nor do they indicate how it
entered the stack.
Add trace events at entry of each of the exported functions, including
most fields that are likely to be interesting for debugging driver
datapath behaviour. Split netif_rx() and netif_receive_skb() so that
internal calls are not traced.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing net/net_dev_xmit trace event provides little information
about the skb that has been passed to the driver, and it is not
simple to add more since the skb may already have been freed at
the point the event is emitted.
Add a separate trace event before the skb is passed to the driver,
including most fields that are likely to be interesting for debugging
driver datapath behaviour.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to set up the partial checksum offset for IP
packets (and optionally re-calculate the pseudo-header checksum) into the
core network code.
The implementation was previously private and duplicated between xen-netback
and xen-netfront, however it is not xen-specific and is potentially useful
to any network driver.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/xfrm/xfrm_policy.c
Steffen Klassert says:
====================
This pull request has a merge conflict between commits be7928d20b
("net: xfrm: xfrm_policy: fix inline not at beginning of declaration") and
da7c224b1b ("net: xfrm: xfrm_policy: silence compiler warning") from
the net-next tree and commit 2f3ea9a95c ("xfrm: checkpatch erros with
inline keyword position") from the ipsec-next tree.
The version from net-next can be used, like it is done in linux-next.
1) Checkpatch cleanups, from Weilong Chen.
2) Fix lockdep complaints when pktgen is used with IPsec,
from Fan Du.
3) Update pktgen to allow any combination of IPsec transport/tunnel mode
and AH/ESP/IPcomp type, from Fan Du.
4) Make pktgen_dst_metrics static, Fengguang Wu.
5) Compile fix for pktgen when CONFIG_XFRM is not set,
from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, after changing the MTU for a device, dev_set_mtu() calls
NETDEV_CHANGEMTU notification, however doesn't verify it's return code -
which can be NOTIFY_BAD - i.e. some of the net notifier blocks refused this
change, and continues nevertheless.
To fix this, verify the return code, and if it's an error - then revert the
MTU to the original one, notify again and pass the error code.
CC: Jiri Pirko <jiri@resnulli.us>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO layer has a limit of 8 flows being held in GRO list,
for performance reason.
When a packet comes for a flow not yet in the list,
and list is full, we immediately give it to upper
stacks, lowering aggregation performance.
With TSO auto sizing and FQ packet scheduler, this situation
happens more often.
This patch changes strategy to simply evict the oldest flow of
the list. This works better because of the nature of packet
trains for which GRO is efficient. This also has the effect
of lowering the GRO latency if many flows are competing.
Tested :
Used a 40Gbps NIC, with 4 RX queues, and 200 concurrent TCP_STREAM
netperf.
Before patch, aggregate rate is 11Gbps (while a single flow can reach
30Gbps)
After patch, line rate is reached.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
0-DAY kernel build testing backend reported below error:
All error/warnings:
net/core/pktgen.c: In function 'pktgen_if_write':
>> >> net/core/pktgen.c:1487:10: error: 'struct pktgen_dev' has no member named 'spi'
>> >> net/core/pktgen.c:1488:43: error: 'struct pktgen_dev' has no member named 'spi'
Fix this by encapuslating the code with CONFIG_XFRM.
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch built on top of Commit 299603e837
("net-gro: Prepare GRO stack for the upcoming tunneling support") to add
the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO
stack. It also serves as an example for supporting other encapsulation
protocols in the GRO stack in the future.
The patch supports version 0 and all the flags (key, csum, seq#) but
will flush any pkt with the S (seq#) flag. This is because the S flag
is not support by GSO, and a GRO pkt may end up in the forwarding path,
thus requiring GSO support to break it up correctly.
Currently the "packet_offload" structure only contains L3 (ETH_P_IP/
ETH_P_IPV6) GRO offload support so the encapped pkts are limited to
IP pkts (i.e., w/o L2 hdr). But support for other protocol type can
be easily added, so is the support for GRE variations like NVGRE.
The patch also support csum offload. Specifically if the csum flag is on
and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE),
the code will take advantage of the csum computed by the h/w when
validating the GRE csum.
Note that commit 60769a5dcd "ipv4: gre:
add GRO capability" already introduces GRO capability to IPv4 GRE
tunnels, using the gro_cells infrastructure. But GRO is done after
GRE hdr has been removed (i.e., decapped). The following patch applies
GRO when pkts first come in (before hitting the GRE tunnel code). There
is some performance advantage for applying GRO as early as possible.
Also this approach is transparent to other subsystem like Open vSwitch
where GRE decap is handled outside of the IP stack hence making it
harder for the gro_cells stuff to apply. On the other hand, some NICs
are still not capable of hashing on the inner hdr of a GRE pkt (RSS).
In that case the GRO processing of pkts from the same remote host will
all happen on the same CPU and the performance may be suboptimal.
I'm including some rough preliminary performance numbers below. Note
that the performance will be highly dependent on traffic load, mix as
usual. Moreover it also depends on NIC offload features hence the
following is by no means a comprehesive study. Local testing and tuning
will be needed to decide the best setting.
All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs.
(super_netperf 50 -H 192.168.1.18 -l 30)
An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1
mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123)
is configured.
The GRO support for pkts AFTER decap are controlled through the device
feature of the GRE device (e.g., ethtool -K gre1 gro on/off).
1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off
thruput: 9.16Gbps
CPU utilization: 19%
1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off
thruput: 5.9Gbps
CPU utilization: 15%
1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 12-13%
1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 10%
The following tests were performed on a different NIC that is capable of
csum offload. I.e., the h/w is capable of computing IP payload csum
(CHECKSUM_COMPLETE).
2.1 ethtool -K gre1 gro on (hence will use gro_cells)
2.1.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 8.53Gbps
CPU utilization: 9%
2.1.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 8.97Gbps
CPU utilization: 7-8%
2.1.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 8.83Gbps
CPU utilization: 5-6%
2.1.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.98Gbps
CPU utilization: 5%
2.2 ethtool -K gre1 gro off
2.2.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 5.93Gbps
CPU utilization: 9%
2.2.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 5.62Gbps
CPU utilization: 8%
2.2.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 7.69Gbps
CPU utilization: 8%
2.2.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.96Gbps
CPU utilization: 5-6%
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many cases where this feature does not improve performance or even
reduces it.
For example, here are the results from tests that I've run using 3.12.6 on one
Intel Xeon W3565 and one i7 920 connected by ixgbe adapters. The results are
from the Xeon, but they're similar on the i7. All numbers report the
mean±stddev over 10 runs of 10s.
1) latency tests similar to what is described in "c6e1a0d net: Allow no-cache
copy from user on transmit"
There is no statistically significant difference between tx-nocache-copy
on/off.
nic irqs spread out (one queue per cpu)
200x netperf -r 1400,1
tx-nocache-copy off
692000±1000 tps
50/90/95/99% latency (us): 275±2/643.8±0.4/799±1/2474.4±0.3
tx-nocache-copy on
693000±1000 tps
50/90/95/99% latency (us): 274±1/644.1±0.7/800±2/2474.5±0.7
200x netperf -r 14000,14000
tx-nocache-copy off
86450±80 tps
50/90/95/99% latency (us): 334.37±0.02/838±1/2100±20/3990±40
tx-nocache-copy on
86110±60 tps
50/90/95/99% latency (us): 334.28±0.01/837±2/2110±20/3990±20
2) single stream throughput tests
tx-nocache-copy leads to higher service demand
throughput cpu0 cpu1 demand
(Gb/s) (Gcycle) (Gcycle) (cycle/B)
nic irqs and netperf on cpu0 (1x netperf -T0,0 -t omni -- -d send)
tx-nocache-copy off 9402±5 9.4±0.2 0.80±0.01
tx-nocache-copy on 9403±3 9.85±0.04 0.838±0.004
nic irqs on cpu0, netperf on cpu1 (1x netperf -T1,1 -t omni -- -d send)
tx-nocache-copy off 9401±5 5.83±0.03 5.0±0.1 0.923±0.007
tx-nocache-copy on 9404±2 5.74±0.03 5.523±0.009 0.958±0.002
As a second example, here are some results from Eric Dumazet with latest
net-next.
tx-nocache-copy also leads to higher service demand
(cpu is Intel(R) Xeon(R) CPU X5660 @ 2.80GHz)
lpq83:~# ./ethtool -K eth0 tx-nocache-copy on
lpq83:~# perf stat ./netperf -H lpq84 -c
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpq84.prod.google.com () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
87380 16384 16384 10.00 9407.44 2.50 -1.00 0.522 -1.000
Performance counter stats for './netperf -H lpq84 -c':
4282.648396 task-clock # 0.423 CPUs utilized
9,348 context-switches # 0.002 M/sec
88 CPU-migrations # 0.021 K/sec
355 page-faults # 0.083 K/sec
11,812,797,651 cycles # 2.758 GHz [82.79%]
9,020,522,817 stalled-cycles-frontend # 76.36% frontend cycles idle [82.54%]
4,579,889,681 stalled-cycles-backend # 38.77% backend cycles idle [67.33%]
6,053,172,792 instructions # 0.51 insns per cycle
# 1.49 stalled cycles per insn [83.64%]
597,275,583 branches # 139.464 M/sec [83.70%]
8,960,541 branch-misses # 1.50% of all branches [83.65%]
10.128990264 seconds time elapsed
lpq83:~# ./ethtool -K eth0 tx-nocache-copy off
lpq83:~# perf stat ./netperf -H lpq84 -c
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpq84.prod.google.com () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
87380 16384 16384 10.00 9412.45 2.15 -1.00 0.449 -1.000
Performance counter stats for './netperf -H lpq84 -c':
2847.375441 task-clock # 0.281 CPUs utilized
11,632 context-switches # 0.004 M/sec
49 CPU-migrations # 0.017 K/sec
354 page-faults # 0.124 K/sec
7,646,889,749 cycles # 2.686 GHz [83.34%]
6,115,050,032 stalled-cycles-frontend # 79.97% frontend cycles idle [83.31%]
1,726,460,071 stalled-cycles-backend # 22.58% backend cycles idle [66.55%]
2,079,702,453 instructions # 0.27 insns per cycle
# 2.94 stalled cycles per insn [83.22%]
363,773,213 branches # 127.757 M/sec [83.29%]
4,242,732 branch-misses # 1.17% of all branches [83.51%]
10.128449949 seconds time elapsed
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
[GIT net-next] Open vSwitch
Open vSwitch changes for net-next/3.14. Highlights are:
* Performance improvements in the mechanism to get packets to userspace
using memory mapped netlink and skb zero copy where appropriate.
* Per-cpu flow stats in situations where flows are likely to be shared
across CPUs. Standard flow stats are used in other situations to save
memory and allocation time.
* A handful of code cleanups and rationalization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the skb zerocopy logic written for nfnetlink queue available for
use by other modules.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_kobject_init() is only being called from __init context,
that is, net_dev_init(), so annotate it with __init as well, thus
the kernel can take this as a hint that the function is used only
during the initialization phase and free up used memory resources
after its invocation.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next tree,
they are:
* Add full port randomization support. Some crazy researchers found a way
to reconstruct the secure ephemeral ports that are allocated in random mode
by sending off-path bursts of UDP packets to overrun the socket buffer of
the DNS resolver to trigger retransmissions, then if the timing for the
DNS resolution done by a client is larger than usual, then they conclude
that the port that received the burst of UDP packets is the one that was
opened. It seems a bit aggressive method to me but it seems to work for
them. As a result, Daniel Borkmann and Hannes Frederic Sowa came up with a
new NAT mode to fully randomize ports using prandom.
* Add a new classifier to x_tables based on the socket net_cls set via
cgroups. These includes two patches to prepare the field as requested by
Zefan Li. Also from Daniel Borkmann.
* Use prandom instead of get_random_bytes in several locations of the
netfilter code, from Florian Westphal.
* Allow to use the CTA_MARK_MASK in ctnetlink when mangling the conntrack
mark, also from Florian Westphal.
* Fix compilation warning due to unused variable in IPVS, from Geert
Uytterhoeven.
* Add support for UID/GID via nfnetlink_queue, from Valentina Giusti.
* Add IPComp extension to x_tables, from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Namespace related cleaning
* make cred_to_ucred static
* remove unused sock_rmalloc function
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it and introduced CGROUP_NET_CLASSID, lets also make
NETPRIO_CGROUP more consistent with the rest of cgroups and rename it
into CONFIG_CGROUP_NET_PRIO so that for networking, we now have
CONFIG_CGROUP_NET_{PRIO,CLASSID}. This not only makes the CONFIG
option consistent among networking cgroups, but also among cgroups
CONFIG conventions in general as the vast majority has a prefix of
CONFIG_CGROUP_<SUBSYS>.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Zefan Li requested [1] to perform the following cleanup/refactoring:
- Split cgroupfs classid handling into net core to better express a
possible more generic use.
- Disable module support for cgroupfs bits as the majority of other
cgroupfs subsystems do not have that, and seems to be not wished
from cgroup side. Zefan probably might want to follow-up for netprio
later on.
- By this, code can be further reduced which previously took care of
functionality built when compiled as module.
cgroupfs bits are being placed under net/core/netclassid_cgroup.c, so
that we are consistent with {netclassid,netprio}_cgroup naming that is
under net/core/ as suggested by Zefan.
No change in functionality, but only code refactoring that is being
done here.
[1] http://patchwork.ozlabs.org/patch/304825/
Suggested-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If user run pktgen plus ipsec by using spi, show spi value
properly when cat /proc/net/pktgen/ethX
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Introduce xfrm_state_lookup_byspi to find user specified by custom
from "pgset spi xxx". Using this scheme, any flow regardless its
saddr/daddr could be transform by SA specified with configurable
spi.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
IPsec tunnel mode encapuslation needs to set outter ip header
with right protocol/ttl/id value with regard to skb->dst->child.
Looking up a rt in a standard way is absolutely wrong for every
packet transmission. In a simple way, construct a dst by setting
neccessary information to make tunnel mode encapuslation working.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
User could set specific SPI value to arm pktgen flow with IPsec
transformation, instead of looking up SA by sadr/daddr. The reaseon
to do so is because current state lookup scheme is both slow and, most
important of all, in fact pktgen doesn't need to match any SA state
addresses information, all it needs is the SA transfromation shell to
do the encapuslation.
And this option also provide user an alternative to using pktgen
test existing SA without creating new ones.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
so /proc/net/xfrm_stat could give user clue about what's
wrong in this process.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The VLAN tag handling code in netpoll_send_skb_on_dev() has two problems.
1) It exits without unlocking the TXQ.
2) It then tries to queue a NULL skb to npinfo->txq.
Reported-by: Ahmed Tamrawi <atamrawi@iastate.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following functions are not used outside of net/core/dev.c
and should be declared static.
call_netdevice_notifiers_info
__dev_remove_offload
netdev_has_any_upper_dev
__netdev_adjacent_dev_remove
__netdev_adjacent_dev_link_lists
__netdev_adjacent_dev_unlink_lists
__netdev_adjacent_dev_unlink
__netdev_adjacent_dev_link_neighbour
__netdev_adjacent_dev_unlink_neighbour
And the following are never used and should be deleted
netdev_lower_dev_get_private_rcu
__netdev_find_adj_rcu
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function __rtnl_af_register is never called outside this
code, and the return value is always 0.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use kfree_skb_list() instead of open coding it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given we allocate memory for each cpu, we can do this
using NUMA affinities, instead of using NUMA policies
of the process changing flow_limit_cpu_bitmap value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful to be able to walk all upper devices when bringing
a device online where the RTNL lock is held. In this case it
is safe to walk the all_adj_list because the RTNL lock is used
to protect the write side as well.
This patch adds a check to see if the rtnl lock is held before
throwing a warning in netdev_all_upper_get_next_dev_rcu().
Also because we now have a call site for lockdep_rtnl_is_held()
outside COFIG_LOCK_PROVING an inline definition returning 1 is
needed. Similar to the rcu_read_lock_is_held().
Fixes: 2a47fa45d4 ("ixgbe: enable l2 forwarding acceleration for macvlans")
CC: Veaceslav Falico <vfalico@redhat.com>
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds skb_copy_hash to copy rxhash and l4_rxhash from one skb to another.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing name of function as part of making the hash in skbuff to be
generic property, not just for receive path.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The neighbour code sends up an RTM_NEWNEIGH netlink notification if
the NUD state of a neighbour cache entry is changed by a timer (e.g.
from REACHABLE to STALE), even if the lladdr of the entry has not
changed.
But an administrative change to the the NUD state of a neighbour cache
entry that does not change the lladdr (e.g. via "ip -4 neigh change
... nud ...") does not trigger a netlink notification. This means
that netlink listeners will not hear about administrative NUD state
changes such as from a resolved state to PERMANENT.
This patch changes the neighbor code to generate an RTM_NEWNEIGH
message when the NUD state of an entry is changed administratively.
Signed-off-by: Bob Gilligan <gilligan@aristanetworks.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These function to manipulate multiple addresses are not used anywhere
in current net-next tree. Some out of tree code maybe using these but
too bad; they should submit their code upstream..
Also, make __hw_addr_flush local since only used by dev_addr_lists.c
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond_first_slave_rcu() will be used to instead of bond_first_slave()
in rcu_read_lock().
According to the Jay Vosburgh's suggestion, the struct netdev_adjacent
should hide from users who wanted to use it directly. so I package a
new function to get the first slave of the bond.
Suggested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Suggested-by: Jay Vosburgh <fubar@us.ibm.com>
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the GRO stack to avoid the use of "network_header"
and associated macros like ip_hdr() and ipv6_hdr() in order to allow
an arbitary number of IP hdrs (v4 or v6) to be used in the
encapsulation chain. This lays the foundation for various IP
tunneling support (IP-in-IP, GRE, VXLAN, SIT,...) to be added later.
With this patch, the GRO stack traversing now is mostly based on
skb_gro_offset rather than special hdr offsets saved in skb (e.g.,
skb->network_header). As a result all but the top layer (i.e., the
the transport layer) must have hdrs of the same length in order for
a pkt to be considered for aggregation. Therefore when adding a new
encap layer (e.g., for tunneling), one must check and skip flows
(e.g., by setting NAPI_GRO_CB(p)->same_flow to 0) that have a
different hdr length.
Note that unlike the network header, the transport header can and
will continue to be set by the GRO code since there will be at
most one "transport layer" in the encap chain.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4191 states in 3.5:
When a host avoids using any non-reachable router X and instead sends
a data packet to another router Y, and the host would have used
router X if router X were reachable, then the host SHOULD probe each
such router X's reachability by sending a single Neighbor
Solicitation to that router's address. A host MUST NOT probe a
router's reachability in the absence of useful traffic that the host
would have sent to the router if it were reachable. In any case,
these probes MUST be rate-limited to no more than one per minute per
router.
Currently, when the neighbour corresponding to a router falls into
NUD_FAILED, it's never considered again. Introduce a new rt6_nud_state
value, RT6_NUD_FAIL_PROBE, which suggests the route should not be used but
should be probed with a single NS. The probe is ratelimited by the existing
code. To better distinguish meanings of the failure values, rename
RT6_NUD_FAIL_SOFT to RT6_NUD_FAIL_DO_RR.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various spelling fixes in networking stack
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
unix_dgram_recvmsg() will hold the readlock of the socket until recv
is complete.
In the same time, we may try to setsockopt(SO_PEEK_OFF) which will hang until
unix_dgram_recvmsg() will complete (which can take a while) without allowing
us to break out of it, triggering a hung task spew.
Instead, allow set_peek_off to fail, this way userspace will not hang.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes compile error when CONFIG_NET_NS is not set.
Introduced by:
commit 1d4c8c2984
"neigh: restore old behaviour of default parms values"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
maxattr in genl_family should be used to save the max attribute
type, but not the max command type. Drop monitor doesn't support
any attributes, so we should leave it as zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the behaviour similar to ipv4. This will allow user to set sysctl
default neigh param values and these values will be respected even by
devices registered before (that ones what do not have address set yet).
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously inet devices were only constructed when addresses are added.
Therefore the default neigh parms values they get are the ones at the
time of these operations.
Now that we're creating inet devices earlier, this changes the behaviour
of default neigh parms values in an incompatible way (see bug #8519).
This patch creates a compromise by setting the default values at the
same point as before but only for those that have not been explicitly
set by the user since the inet device's creation.
Introduced by:
commit 8030f54499
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Thu Feb 22 01:53:47 2007 +0900
[IPV4] devinet: Register inetdev earlier.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be needed later on to provide better management of default values.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the neigh param members to an array. This allows easier
manipulation which will be needed later on to provide better management of
default values.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we need it elsewhere, move the inline helper function of
skb_needs_linearize() over to skbuff.h include file. While
at it, also convert the return to 'bool' instead of 'int'
and add a proper kernel doc.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers use dev_kfree_skb_any() and dev_kfree_skb_irq()
helpers to free skbs, both for dropped packets and TX completed ones.
We need to separate the two causes to get better diagnostics
given by dropwatch or "perf record -e skb:kfree_skb"
This patch provides two new helpers, dev_consume_skb_any() and
dev_consume_skb_irq() to be used for consumed skbs.
__dev_kfree_skb_irq() is slightly optimized to remove one
atomic_dec_and_test() in fast path, and use this_cpu_{r|w} accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one useless conditional branch :
napi->skb is NULL, so nothing bad can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must clear local_df when passing the skb between namespaces as the
packet is not local to the new namespace any more and thus may not get
fragmented by local rules. Fred Templin noticed that other namespaces
do fragment IPv6 packets while forwarding. Instead they should have send
back a PTB.
The same problem should be present when forwarding DF-IPv4 packets
between namespaces.
Reported-by: Templin, Fred L <Fred.L.Templin@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of conversion to kernfs, cgroup file handling is
updated so that it can be easily mapped to kernfs. This patch
replaces cftype->read_seq_string() with cftype->seq_show() which is
not limited to single_open() operation and will map directcly to
kernfs seq_file interface.
The conversions are mechanical. As ->seq_show() doesn't have @css and
@cft, the functions which make use of them are converted to use
seq_css() and seq_cft() respectively. In several occassions, e.f. if
it has seq_string in its name, the function name is updated to fit the
new method better.
This patch does not introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
In preparation of conversion to kernfs, cgroup file handling is being
consolidated so that it can be easily mapped to the seq_file based
interface of kernfs.
cftype->read_map() doesn't add any value and being replaced with
->read_seq_string(). Update read_priomap() to use ->read_seq_string()
instead.
This patch doesn't make any visible behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Li Zefan <lizefan@huawei.com>
commit a553e4a631 ("[PKTGEN]: IPSEC support")
tried to support IPsec ESP transport transformation for pktgen, but acctually
this doesn't work at all for two reasons(The orignal transformed packet has
bad IPv4 checksum value, as well as wrong auth value, reported by wireshark)
- After transpormation, IPv4 header total length needs update,
because encrypted payload's length is NOT same as that of plain text.
- After transformation, IPv4 checksum needs re-caculate because of payload
has been changed.
With this patch, armmed pktgen with below cofiguration, Wireshark is able to
decrypted ESP packet generated by pktgen without any IPv4 checksum error or
auth value error.
pgset "flag IPSEC"
pgset "flows 1"
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently GRO started generating packets with frag_lists of frags.
This was not handled by GSO, thus leading to a crash.
Thankfully these packets are of a regular form and are easy to
handle. This patch handles them in two ways. For completely
non-linear frag_list entries, we simply continue to iterate over
the frag_list frags once we exhaust the normal frags. For frag_list
entries with linear parts, we call pskb_trim on the first part
of the frag_list skb, and then process the rest of the frags in
the usual way.
This patch also kills a chunk of dead frag_list code that has
obviously never ever been run since it ends up generating a bogus
GSO-segmented packet with a frag_list entry.
Future work is planned to split super big packets into TSO
ones.
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Reported-by: Jerry Chu <hkchu@google.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit:
b6c40d68ff
net: only invoke dev->change_rx_flags when device is UP
tried to fix a problem with VLAN devices and promiscuouse flag setting.
The issue was that VLAN device was setting a flag on an interface that
was down, thus resulting in bad promiscuity count.
This commit blocked flag propagation to any device that is currently
down.
A later commit:
deede2fabe
vlan: Don't propagate flag changes on down interfaces
fixed VLAN code to only propagate flags when the VLAN interface is up,
thus fixing the same issue as above, only localized to VLAN.
The problem we have now is that if we have create a complex stack
involving multiple software devices like bridges, bonds, and vlans,
then it is possible that the flags would not propagate properly to
the physical devices. A simple examle of the scenario is the
following:
eth0----> bond0 ----> bridge0 ---> vlan50
If bond0 or eth0 happen to be down at the time bond0 is added to
the bridge, then eth0 will never have promisc mode set which is
currently required for operation as part of the bridge. As a
result, packets with vlan50 will be dropped by the interface.
The only 2 devices that implement the special flag handling are
VLAN and DSA and they both have required code to prevent incorrect
flag propagation. As a result we can remove the generic solution
introduced in b6c40d68ff and leave
it to the individual devices to decide whether they will block
flag propagation or not.
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drop monitor code is abusing the genetlink API and is
statically using the generic netlink multicast group 1, even
if that group belongs to somebody else (which it invariably
will, since it's not reserved.)
Make the drop monitor code use the proper APIs to reserve a
group ID, but also reserve the group id 1 in generic netlink
code to preserve the userspace API. Since drop monitor can
be a module, don't clear the bit for it on unregistration.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIOCSHWTSTAMP returns the real configuration to the application
using it, but there is currently no way for any other
application to find out the configuration non-destructively.
Add a new ioctl for this, making it unprivileged.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
A macvlan device has always LRO disabled so that calling
dev_disable_lro() on it does nothing. If we need to disable LRO
e.g. because
- the macvlan device is inserted into a bridge
- IPv6 forwarding is enabled for it
- it is in a different namespace than lowerdev and IPv4
forwarding is enabled in it
we need to disable LRO on its underlying device instead (as we
do for 802.1q VLAN devices).
v2: use newly introduced netif_is_macvlan()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genl_ops are no longer modified in place when
registering, they can be made const. This patch was done
mostly with spatch:
@@
identifier ops;
@@
+const
struct genl_ops ops[] = {
...
};
(except the struct thing in net/openvswitch/datapath.c)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 06a23fe31c
("core/dev: set pkt_type after eth_type_trans() in dev_forward_skb()")
and refactoring 64261f230a
("dev: move skb_scrub_packet() after eth_type_trans()")
are forcing pkt_type to be PACKET_HOST when skb traverses veth.
which means that ip forwarding will kick in inside netns
even if skb->eth->h_dest != dev->dev_addr
Fix order of eth_type_trans() and skb_scrub_packet() in dev_forward_skb()
and in ip_tunnel_rcv()
Fixes: 06a23fe31c ("core/dev: set pkt_type after eth_type_trans() in dev_forward_skb()")
CC: Isaku Yamahata <yamahatanetdev@gmail.com>
CC: Maciej Zenczykowski <zenczykowski@gmail.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
Pushing original fragments through causes several problems. For example
for matching, frags may not be matched correctly. Take following
example:
<example>
On HOSTA do:
ip6tables -I INPUT -p icmpv6 -j DROP
ip6tables -I INPUT -p icmpv6 -m icmp6 --icmpv6-type 128 -j ACCEPT
and on HOSTB you do:
ping6 HOSTA -s2000 (MTU is 1500)
Incoming echo requests will be filtered out on HOSTA. This issue does
not occur with smaller packets than MTU (where fragmentation does not happen)
</example>
As was discussed previously, the only correct solution seems to be to use
reassembled skb instead of separete frags. Doing this has positive side
effects in reducing sk_buff by one pointer (nfct_reasm) and also the reams
dances in ipvs and conntrack can be removed.
Future plan is to remove net/ipv6/netfilter/nf_conntrack_reasm.c
entirely and use code in net/ipv6/reassembly.c instead.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to delete a table >= 256 using iproute2 the local table
will be deleted.
The table id is specified as a netlink attribute when it needs more then
8 bits and iproute2 then sets the table field to RT_TABLE_UNSPEC (0).
Preconditions to matching the table id in the rule delete code
doesn't seem to take the "table id in netlink attribute" into condition
so the frh_get_table helper function never gets to do its job when
matching against current rule.
Use the helper function twice instead of peaking at the table value directly.
Originally reported at: http://bugs.debian.org/724783
Reported-by: Nicolas HICHER <nhicher@avencall.com>
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
By moving code around, we avoid :
1) A reload of iph->ihl (bit field, so needs a mask)
2) A conditional test (replaced by a conditional mov on x86)
Fast path loads iph->protocol anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "@" to refer to parameters in the kernel-doc description. According
to Documentation/kernel-doc-nano-HOWTO.txt "&" shall be used to refer to
structures only.
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function has usage beside IPsec so move it to the core skbuff code.
While doing so, give it some documentation and change its return type to
'unsigned char *' to be in line with skb_put().
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a operations structure that allows a network interface to export
the fact that it supports package forwarding in hardware between
physical interfaces and other mac layer devices assigned to it (such
as macvlans). This operaions structure can be used by virtual mac
devices to bypass software switching so that forwarding can be done
in hardware more efficiently.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they all
get slowly migrated over to the safe versions of the attribute groups
(removing userspace races with the creation of the sysfs files.) Also
in here are some kobject updates, devres expansions, and the first round
of Tejun's sysfs reworking to enable it to be used by other subsystems
as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xAMACgkQMUfUDdst+yk1kQCfcHXhfnrvFZ5J/mDP509IzhNS
ddEAoLEWoivtBppNsgrWqXpD1vi4UMsE
=JmVW
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they
all get slowly migrated over to the safe versions of the attribute
groups (removing userspace races with the creation of the sysfs
files.) Also in here are some kobject updates, devres expansions, and
the first round of Tejun's sysfs reworking to enable it to be used by
other subsystems as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (83 commits)
sysfs: rename sysfs_assoc_lock and explain what it's about
sysfs: use generic_file_llseek() for sysfs_file_operations
sysfs: return correct error code on unimplemented mmap()
mdio_bus: convert bus code to use dev_groups
device: Make dev_WARN/dev_WARN_ONCE print device as well as driver name
sysfs: separate out dup filename warning into a separate function
sysfs: move sysfs_hash_and_remove() to fs/sysfs/dir.c
sysfs: remove unused sysfs_get_dentry() prototype
sysfs: honor bin_attr.attr.ignore_lockdep
sysfs: merge sysfs_elem_bin_attr into sysfs_elem_attr
devres: restore zeroing behavior of devres_alloc()
sysfs: fix sysfs_write_file for bin file
input: gameport: convert bus code to use dev_groups
input: serio: remove bus usage of dev_attrs
input: serio: use DEVICE_ATTR_RO()
i2o: convert bus code to use dev_groups
memstick: convert bus code to use dev_groups
tifm: convert bus code to use dev_groups
virtio: convert bus code to use dev_groups
ipack: convert bus code to use dev_groups
...
Sometimes we need to coalesce the rx frags to avoid frag list. One example is
virtio-net driver which tries to use small frags for both MTU sized packet and
GSO packet. So this patch introduce skb_coalesce_rx_frag() to do this.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael Dalton <mwdalton@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a build warning in skb_checksum() by wrapping the
csum_partial() usage in skb_checksum(). The problem is that on a few
architectures, csum_partial is used with prefix asmlinkage whereas
on most architectures it's not. So fix this up generically as we did
with csum_block_add_ext() to match the signature. Introduced by
2817a336d4 ("net: skb_checksum: allow custom update/combine for
walking skb").
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Joby Poriyath provided a xen-netback patch to reduce the size of
xenvif structure as some netdev allocation could fail under
memory pressure/fragmentation.
This patch is handling the problem at the core level, allowing
any netdev structures to use vmalloc() if kmalloc() failed.
As vmalloc() adds overhead on a critical network path, add __GFP_REPEAT
to kzalloc() flags to do this fallback only when really needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Joby Poriyath <joby.poriyath@citrix.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, skb_checksum walks over 1) linearized, 2) frags[], and
3) frag_list data and calculats the one's complement, a 32 bit
result suitable for feeding into itself or csum_tcpudp_magic(),
but unsuitable for SCTP as we're calculating CRC32c there.
Hence, in order to not re-implement the very same function in
SCTP (and maybe other protocols) over and over again, use an
update() + combine() callback internally to allow for walking
over the skb with different algorithms.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't validate iph->ihl which may lead a dead loop if we meet a IPIP
skb whose iph->ihl is zero. Fix this by failing immediately when iph->ihl
is evil (less than 5).
This issue were introduced by commit ec5efe7946
(rps: support IPIP encapsulation).
Cc: Eric Dumazet <edumazet@google.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now skb->data is passed to rx_hook() even if the skb
has not been linearised and without giving rx_hook() a way
to linearise it.
Change the rx_hook() interface and make it accept the skb
and the offset to the UDP payload as arguments. rx_hook() is
also renamed to rx_skb_hook() to ensure that out of the tree
users notice the API change.
In this way any rx_skb_hook() implementation can perform all
the needed operations to properly (and safely) access the
skb data.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We also can defer the initialization of hashrnd in flow_dissector
to its first use. Since net_get_random_once is irq safe now we don't
have to audit the call paths if one of this functions get called by an
interrupt handler.
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I initial build non irq safe version of net_get_random_once because I
would liked to have the freedom to defer even the extraction process of
get_random_bytes until the nonblocking pool is fully seeded.
I don't think this is a good idea anymore and thus this patch makes
net_get_random_once irq safe. Now someone using net_get_random_once does
not need to care from where it is called.
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I think that a dev_put() is needed in the error path to preserve the
proper dev refcount.
CC: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently net_secret_init does not get inlined, so we always have a call
to net_secret_init even in the fast path.
Let's specify net_secret_init as __always_inline so we have the nop in
the fast-path without the call to net_secret_init and the unlikely path
at the epilogue of the function.
jump_labels handle the inlining correctly.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
What sk_reset_txq() does is just calls function sk_tx_queue_reset(),
and sk_reset_txq() is used only in sock.h, by dst_negative_advice().
Let dst_negative_advice() calls sk_tx_queue_reset() directly so we
can remove unneeded sk_reset_txq().
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ipv6_gso_segment() is stackable, its relatively easy to
implement GSO/TSO support for SIT tunnels
Performance results, when segmentation is done after tunnel
device (as no NIC is yet enabled for TSO SIT support) :
Before patch :
lpq84:~# ./netperf -H 2002:af6:1153:: -Cc
MIGRATED TCP STREAM TEST from ::0 (::) port 0 AF_INET6 to 2002:af6:1153:: () port 0 AF_INET6
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 3168.31 4.81 4.64 2.988 2.877
After patch :
lpq84:~# ./netperf -H 2002:af6:1153:: -Cc
MIGRATED TCP STREAM TEST from ::0 (::) port 0 AF_INET6 to 2002:af6:1153:: () port 0 AF_INET6
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 5525.00 7.76 5.17 2.763 1.840
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_get_random_once is a new macro which handles the initialization
of secret keys. It is possible to call it in the fast path. Only the
initialization depends on the spinlock and is rather slow. Otherwise
it should get used just before the key is used to delay the entropy
extration as late as possible to get better randomness. It returns true
if the key got initialized.
The usage of static_keys for net_get_random_once is a bit uncommon so
it needs some further explanation why this actually works:
=== In the simple non-HAVE_JUMP_LABEL case we actually have ===
no constrains to use static_key_(true|false) on keys initialized with
STATIC_KEY_INIT_(FALSE|TRUE). So this path just expands in favor of
the likely case that the initialization is already done. The key is
initialized like this:
___done_key = { .enabled = ATOMIC_INIT(0) }
The check
if (!static_key_true(&___done_key)) \
expands into (pseudo code)
if (!likely(___done_key > 0))
, so we take the fast path as soon as ___done_key is increased from the
helper function.
=== If HAVE_JUMP_LABELs are available this depends ===
on patching of jumps into the prepared NOPs, which is done in
jump_label_init at boot-up time (from start_kernel). It is forbidden
and dangerous to use net_get_random_once in functions which are called
before that!
At compilation time NOPs are generated at the call sites of
net_get_random_once. E.g. net/ipv6/inet6_hashtable.c:inet6_ehashfn (we
need to call net_get_random_once two times in inet6_ehashfn, so two NOPs):
71: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1)
76: 0f 1f 44 00 00 nopl 0x0(%rax,%rax,1)
Both will be patched to the actual jumps to the end of the function to
call __net_get_random_once at boot time as explained above.
arch_static_branch is optimized and inlined for false as return value and
actually also returns false in case the NOP is placed in the instruction
stream. So in the fast case we get a "return false". But because we
initialize ___done_key with (enabled != (entries & 1)) this call-site
will get patched up at boot thus returning true. The final check looks
like this:
if (!static_key_true(&___done_key)) \
___ret = __net_get_random_once(buf, \
expands to
if (!!static_key_false(&___done_key)) \
___ret = __net_get_random_once(buf, \
So we get true at boot time and as soon as static_key_slow_inc is called
on the key it will invert the logic and return false for the fast path.
static_key_slow_inc will change the branch because it got initialized
with .enabled == 0. After static_key_slow_inc is called on the key the
branch is replaced with a nop again.
=== Misc: ===
The helper defers the increment into a workqueue so we don't
have problems calling this code from atomic sections. A seperate boolean
(___done) guards the case where we enter net_get_random_once again before
the increment happend.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now inet_gso_segment() is stackable, its relatively easy to
implement GSO/TSO support for IPIP
Performance results, when segmentation is done after tunnel
device (as no NIC is yet enabled for TSO IPIP support) :
Before patch :
lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 3357.88 5.09 3.70 2.983 2.167
After patch :
lpq83:~# ./netperf -H 7.7.9.84 -Cc
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.9.84 () port 0 AF_INET
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % S us/KB us/KB
87380 16384 16384 10.00 7710.19 4.52 6.62 1.152 1.687
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support GSO on IPIP, we need to make
inet_gso_segment() stackable.
It should not assume network header starts right after mac
header.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While implementing GSO/TSO support for IPIP, I found skb_segment()
was assuming network header was immediately following mac header.
Its not really true in the case inet_gso_segment() is stacked :
By the time tcp_gso_segment() is called, network header points
to the inner IP header.
Let's instead assume nothing and pick the current offsets found in
original skb, we have skb_headers_offset_update() helper for that.
Also move the csum_start update inside skb_headers_offset_update()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on virtio_net new allocation strategy to increase
payload/truesize ratio, we found that refactoring sk_page_frag_refill()
was needed.
This patch splits sk_page_frag_refill() into two parts, adding
skb_page_frag_refill() which can be used without a socket.
While we are at it, add a minimum frag size of 32 for
sk_page_frag_refill()
Michael will either use netdev_alloc_frag() from softirq context,
or skb_page_frag_refill() from process context in refill_work()
(GFP_KERNEL allocations)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gro_receive() is currently limited to 16 or 17 MSS per GRO skb,
typically 24616 bytes, because it fills up to MAX_SKB_FRAGS frags.
It's relatively easy to extend the skb using frag_list to allow
more frags to be appended into the last sk_buff.
This still builds very efficient skbs, and allows reaching 45 MSS per
skb.
(45 MSS GRO packet uses one skb plus a frag_list containing 2 additional
sk_buff)
High speed TCP flows benefit from this extension by lowering TCP stack
cpu usage (less packets stored in receive queue, less ACK packets
processed)
Forwarding setups could be hurt, as such skbs will need to be
linearized, although its not a new problem, as GRO could already
provide skbs with a frag_list.
We could make the 65536 bytes threshold a tunable to mitigate this.
(First time we need to linearize skb in skb_needs_linearize(), we could
lower the tunable to ~16*1460 so that following skb_gro_receive() calls
build smaller skbs)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_secret() is only used when CONFIG_IPV6 or CONFIG_INET are selected.
Building a defconfig with both of these symbols unselected (Using the ARM
at91sam9rl_defconfig, for example) leads to the following build warning:
$ make at91sam9rl_defconfig
#
# configuration written to .config
#
$ make net/core/secure_seq.o
scripts/kconfig/conf --silentoldconfig Kconfig
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
make[1]: `include/generated/mach-types.h' is up to date.
CALL scripts/checksyscalls.sh
CC net/core/secure_seq.o
net/core/secure_seq.c:17:13: warning: 'net_secret_init' defined but not used [-Wunused-function]
Fix this warning by protecting the definition of net_secret() with these
symbols.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Steinar reported FQ pacing was not working for UDP flows.
It looks like the initial sk->sk_pacing_rate value of 0 was
a wrong choice. We should init it to ~0U (unlimited)
Then, TCA_FQ_FLOW_DEFAULT_RATE should be removed because it makes
no real sense. The default rate is really unlimited, and we
need to avoid a zero divide.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the tasks have been migrated to the cgroup,
there is no need to call task_netprioidx to get
task's cgroup id.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the unreg_list and the close_list in dev_close_many preventing
dev_close_many from permuting the unreg_list. The permutations of the
unreg_list have resulted in cases where the loopback device is accessed
it has been freed in code such as dst_ifdown. Resulting in subtle memory
corruption.
This is the second bug from sharing the storage between the close_list
and the unreg_list. The issues that crop up with sharing are
apparently too subtle to show up in normal testing or usage, so let's
forget about being clever and use two separate lists.
v2: Make all callers pass in a close_list to dev_close_many
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio wants to pass in cpumask_of(cpu), make parameter
const to avoid build warnings.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code that extracts the ports from skb_flow_dissect and
add a new function skb_flow_get_ports which can be re-used.
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8ed781668d ("flow_keys: include thoff into flow_keys for
later usage"), we missed that existing code was using nhoff as a
temporary variable that could not always contain transport header
offset.
This is not a problem for TCP/UDP because port offset (@poff)
is 0 for these protocols.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masanari Iida