Change driver version to 4.0.0. Netxen firmwares as old as
v3.4.216 are supported.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NX3031 supports cut-through operation where ingress packets are
directly dma'ed into host buffers to reduce latency.
This requires larger dma buffers (2kb) and different alignemnt.
The buffer posting logic is changed a bit. The free rx buffers
are maintained in linked list, since the received reference
handles can be out of order. However rx descriptors are still
posted sequentially, indexed by producer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAC addr, multicast filters, mtu are set through firmware commands
in firmware v4.0.0+ because of virtualization of physical ports.
Link status is also read from registers allocated by firmware for
each virtual port.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Contains rx and tx ring context management and certain
firmware commands for netxen firmware v4.0.0+.
This patch gathers all HW context management code into
netxen_nic_ctx.c.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It had only couple of functions which are moved to main.c
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add initialization code in pci probe for new chip and retain
compatibility with old revisions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New revision of netxen chip has 2MB PCI memory. Older chips
had 128MB addressable PCI memory. To retain compatibility,
this patch adds function pointers based on pci bar0 size.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add macros for new chip revision and board configurations.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable multicast address filtering capabilities in the hardware.
Upto 16 multicast addresses can be programmed for each physical
port. Support "allmulti" mode, if enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Reduce access to global arrays in data path.
o Remove duplicate/unused variables, unecessary alignment constraints.
o Use correct pci_dev instead of fallback device for consistent
allocations.
o Disable ethtool set_eeprom functionality for now, it was only used
for flashing firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PCI_DEVICE_CLASS sets .device and .vendor to PCI_ANY_DEV,
which overrides the effect of preceding PCI_DEVICE() and makes
all elements of netxen_pci_tbl[] identical. Introduced in the
commit dcd56fdbae.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Store physical port number in netxen_adapter structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Don't need to keep a struct netxen_new_user_info on the stack
when we only are interested in printing the serial_num. Change
to only reading the serial_num.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
This patch #if 0's the no longer used netxen_nic_link_ok().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Don't count rx dropped packets based on return value of netif_receive_skb(),
which is misleading.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o eliminate tx lock in netxen adapter struct, instead pound on netdev
tx lock appropriately.
o remove old "concurrent transmit" code that unnecessarily drops and
reacquires tx lock in hard_xmit_frame(), this is already serialized
the netdev xmit lock.
o reduce scope of tx lock in tx cleanup. tx cleanup operates on
different section of the ring than transmitting cpus and is
guarded by producer and consumer indices. This fixes a race
caused by rx softirq preemption on realtime kernels.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o separate and simpler irq handler for msi interrupts, avoids few checks
than legacy mode.
o avoid redudant tx_has_work() and rx_has_work() checks in interrupt
and napi, which can uncork irq based on racy (lockless) access to tx
and rx ring indices. If we get interrupt, there's sufficient reason to
schedule napi.
o replenish rx ring more often, remove self-imposed threshold rcv_free
that prevents posting rx desc to card. This improves performance in
low memory.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent netxen firmware has new scheme of generating MSI interrupts, it
raises interrupt and blocks itself, waiting for driver to unmask. This
reduces chance of spurious interrupts.
The driver will be able to deal with older firmware as well.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following cleanups:
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- #if 0 unused code
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using ARRAY_SIZE() on arrays of the form array[][K] makes it unnecessary
to know the value of K when checking its size.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Here's the reworked patch.
This cleans up some unnecessary byte-swapping while setting up tx and
interpreting rx desc. The 64 bit rx status data should be converted
to host endian format only once and the macros just need to extract
bitfields.
This saves a spate of interrupts on pseries blades caused by buggy
(non) processing rx status ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
netxen driver allows limited number of threads simultaneously posting
skb's in tx ring. If transmit slot is unavailable, driver calls
schedule() or loops in xmit_frame().
This patch returns TX_BUSY and lets the stack reschedule the packet if
transmit slot is unavailable. Also removes unnecessary check for tx
timeout in the driver itself, the network stack does that anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes bug that doesn't quiesce second port when interface is
brought down, which could lead to unwarranted interrupt during rmmod /
ifdown.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bumping up driver version to 3.4.18, several fixes have gone in since
version 3.4.2.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove redundant DMA_..BIT_MASK definitions across two drivers. The
computation of the majority of the bitmasks is done by the compiler. The
initial split of the patch touching each a different file got removed due
to possible git bisect breakage.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Reviewed-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Resubmitting the patch.
This patch improves ethtool support for printing correct ring statistics,
segmentation offload status, etc.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch covers something like this:
dev = alloc_*dev(...
...
priv = netdev_priv(dev);
memset(priv, 0, sizeof(*priv));
The memset() here is superfluous. alloc_netdev() uses kzalloc()
to allocate needed memory so there is no need to zero the priv region
twice.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up duplicate includes in
drivers/net/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two problems during driver unload. The pci_disable_device()
call is before firmware reload, causing reads and writes across PCI bus after
disabling device. Second problem is the register window was wrong during
firmware reload
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Loading firmware during PCI probe can lead to incorrect initialization,
rendering the card unusable until next reboot. This was introduced a while
ago as a workaround for firmware bug, a better workaround was submitted for
this a while ago. So removing original hack that loads firmware during probe.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some leftover code that makes use of adapter->lock in tx_timeout function,
which resets the interface under this lock. In close() when the workqueue
is flushed, prints the warning about sleeping with interrupts disabled
(when spinlock debug is enabled). The lock was required with private netxen
IOCTLs, which were removed a while ago.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes masking of interrupts on multiport adapters. Also disables
interrupts upon ifdown interface. The wrong mask could result in interrupt
flood after interface is down.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for firmware bug with 2nd port of multiport adapter,
where MAC address is reset. Driver just needs to overwrite it with the
value read from PROM.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The firmware should be loaded after resetting hardware during PCI probe,
besides module unload. This fixes issue with 2nd port of multiport adapter
on powerpc blades. This patch also fixes a bug that PCI resources are not
freed if dma watchdog shutdown failed. The dma watchdog poll messages
during module unload are also suppressed.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of dubious casts to (void *) which causes a sparse warning.
And move largeish function from inline to the one file that uses the code,
the compiler can then decide to inline it.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent gcc versions emit warnings when unsigned variables are compared < 0 or >= 0.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resending patch 3/3 only.
These changes allow driver close routine to be called during module unload,
to clean-up buffers and other software resources, flush queues etc. Also,
hardware is reset to pristine state.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates the various access routines to access different
control and status settings present in different register locations.
This will fix problems related to working of different ports in
multi Port card.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen driver uses PCI function 0 to provide the functionality of MSI.
The patch makes driver check the bus master bit for function 0 and
enable it after the card initialization.
Signed-off-by: Dhananjay Phadke<dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix incorrect link status even with switch turned OFF.
NetXen driver failed to accurately indicate when a link is up or down.
This was encountered during failover testing, when the first port
indicated that the link was up even when the 10G switch it was assigned
to in the Bladecenter was turned off completely.
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Add NETXEN prefixes to macros to clean them up.
This is a cleanup patch which adds NETXEN prefix to some stand
alone macro names.
These posed compile errors when NetXen driver was backported to 2.6.9
on PPC architecture as macros like USER_START are defined in file
arch/ppc64/mm/hash_utils.c
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Acked-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix initialization and subsequent ping issue on 3.4.19 firmware
This patch fixes the ping problem seen X/PBlades after the adapter's
firmware was moved to 3.4.19. After configured interface up, ping
failed.
NetXen adapter couldn't accept ARP broadcast packet. Manual addition of
MAC address in the ARP table, made ping work.
NetXen adapter should finish initilization after system boot. But looks
NetXen adapter didn't initilization correctly after system boot up.
So have to re-load the firmware again in probe routine.
Also re-initilization netxen_config_0 and netxen_config_1 registers.
Signed-off by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Removal of redundant free_irq
This patch removes a redundant free_irq() call from remove() routine.
This will also eliminate a warning during unload of driver.
Signed-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix for driver on System-p
This patch will fix a ping issue on system-p
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Adhiraj Joshi <adhiraj@netxen.com>
Signed-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/netxen/netxen_nic_main.c: In function 'netxen_nic_open':
drivers/net/netxen/netxen_nic_main.c:738: warning: 'deprecated_irq_flag' is deprecated (declared at include/linux/interrupt.h:66)
drivers/net/netxen/netxen_nic_main.c:738: warning: 'deprecated_irq_flag' is deprecated (declared at include/linux/interrupt.h:66)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix vmalloc errors on seen on some X86 high end machines.
Signed-off by: Milan Bag <mbag@netxen.com>
Acked-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix PPC architecture specific bugs
Fixes some issues seen on Big endian machines.
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Port Swap feature
This patch will allow a port numbers on the card to be swapped in
host driver. This feature is applicable to cards having more than
1 port.
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix the multi PCI function for cards with more than 2 ports.
This patch fixes the working of multi PCI capable driver on cards with
more than 2 ports by adding the addresses for their rings and sizes.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Removal of redundant function call parameters and bug fixes.
This patch will remove the redundant paramters which were being passed to
many functions since now adapter->portnum can be used.
Signed-off-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Make driver use multiple PCI functions.
This patch will make NetXen driver work with multiple PCI functions. This will
make the usage of memory resources as well as interrupts more independent
among different functions which results in better throughput. This change has
been done after the multiport support is added in firmware.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.
Ditched a no-op in bnx2 in the process.
I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->h.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...
Just out of curiosity, here are the idioms found to get the same result:
skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->nh.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetXen: This will fix a softlock seen on some machines.
The reason was too much time was spent waiting for hardware access
to go through.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Set the MTU for the right port depending upon the port number
for XG cards.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CC [M] drivers/net/netxen/netxen_nic_hw.o
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_hw_resources':
drivers/net/netxen/netxen_nic_hw.c:231: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'dma_addr_t'
drivers/net/netxen/netxen_nic_hw.c:250: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'dma_addr_t'
u64 is unsigned long so the cast to u64 will result in a warning on the
printf arguments for 64-bit builds. So cast to unsigned long long instead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Compiler warning spots real error!
The function do_rom_fast_read called in do_rom_fast_write can fail
and leave data1 unset. This causes a compile warning.
The correct thing is to propagate the error out.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Added ethtool support for user level firmware management utilities.
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This will use pci_register_driver() instead of pci_module_init().
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch is to make the driver work with multiple minor firmware versions
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (42 commits)
r8169: extraneous Cmd{Tx/Rx}Enb write
forcedeth: modified comment header
NetXen: Reducing ring sizes for IOMMU issue.
NetXen: Fix for PPC machines.
NetXen: work queue fixes.
NetXen: Link status message correction for quad port cards.
NetXen: Multiple adapter fix.
NetXen: Using correct CHECKSUM flag.
NetXen: driver reload fix for newer firmware.
NetXen: Adding new device ids.
PHY probe not working properly for ibm_emac (PPC4xx)
ep93xx: some minor cleanups to the ep93xx eth driver
sky2: phy power down needs PCI config write enabled
sky2: power management/MSI workaround
sky2: dual port NAPI problem
via-velocity uses INET interfaces
e1000: Do not truncate TSO TCP header with 82544 workaround
myri10ge: handle failures in suspend and resume
myri10ge: no need to save MSI and PCIe state in the driver
myri10ge: make msi configurable at runtime through sysfs
...
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic.h | 10 +++++-----
1 files changed, 5 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_isr.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_hw.c | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 7 +++++++
1 files changed, 7 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 2 ++
1 files changed, 2 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The netxen driver includes a private ioctl that provides access
to functionality that is already available in other ways. The PCI
layer has application access hooks (see setpci), and the statistics
are available in ethtool/netstats.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix up arch-specific work items where possible to use the new work_struct and
delayed_work structs.
Three places that enqueue bits of their stack and then return have been marked
with #error as this is not permitted.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
David S. Miller