Should NOT check SMAC=DMAC when:
1. loopback is turned on
2. validate_loopback is true.
Fixed it accordingly.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates and fixes from David Miller:
1) Reinstate the no-ref optimization for input route lookups in ipv4 to
fix some routing cache removal perf regressions.
2) Make TCP socket pre-demux work on ipv6 side too, from Eric Dumazet.
3) Get RX hash value from correct place in be2net driver, from
Sarveshwar Bandi.
4) Validation of FIB cached routes missing critical check, from Eric
Dumazet.
5) EEH support in mlx4 driver, from Kleber Sacilotto de Souza.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
ipv6: Early TCP socket demux
ipv4: Fix input route performance regression.
pch_gbe: vlan skb len fix
pch_gbe: add extra clean tx
pch_gbe: fix transmit watchdog timeout
ixgbe: fix panic while dumping packets on Tx hang with IOMMU
be2net: Fix to parse RSS hash from Receive completions correctly.
net/mlx4_en: Limit the RFS filter IDs to be < RPS_NO_FILTER
hyperv: Add error handling to rndis_filter_device_add()
hyperv: Add a check for ring_size value
ipv4: rt_cache_valid must check expired routes
net/pch_gpe: Cannot disable ethernet autonegation
qeth: repair crash in qeth_l3_vlan_rx_kill_vid()
netiucv: cleanup attribute usage
net: wiznet add missing HAS_IOMEM dependency
be2net: Missing byteswap in be_get_fw_log_level causes oops on PowerPC
mlx4: Add support for EEH error recovery
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
wanmain: comparing array with NULL
caif: fix NULL pointer check
...
RFS filter id can't have the special value RPS_NO_FILTER,
need to skip it when allocating id's.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the mlx4 drivers don't have the necessary callbacks to
implement EEH errors detection and recovery, so the PCI layer uses the
probe and remove callbacks to try to recover the device after an error on
the bus. However, these callbacks have race conditions with the internal
catastrophic error recovery functions, which will also detect the error
and this can cause the system to crash if both EEH and catas functions
try to reset the device.
This patch adds the necessary error recovery callbacks and makes sure
that the internal catastrophic error functions will not try to reset the
device in such scenarios. It also adds some calls to
pci_channel_offline() to suppress reads/writes on the bus when the slot
cannot accept I/O operations so we prevent unnecessary accesses to the
bus and speed up the device removal.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates to the qib low-level driver
- First chunk of changes for SR-IOV support for mlx4 IB
- RDMA CM support for IPv6-only binding
- Other misc cleanups and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=f09j
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Updates to the qib low-level driver
- First chunk of changes for SR-IOV support for mlx4 IB
- RDMA CM support for IPv6-only binding
- Other misc cleanups and fixes
Fix up some add-add conflicts in include/linux/mlx4/device.h and
drivers/net/ethernet/mellanox/mlx4/main.c
* tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
IB/qib: checkpatch fixes
IB/qib: Add congestion control agent implementation
IB/qib: Reduce sdma_lock contention
IB/qib: Fix an incorrect log message
IB/qib: Fix QP RCU sparse warnings
mlx4: Put physical GID and P_Key table sizes in mlx4_phys_caps struct and paravirtualize them
mlx4_core: Allow guests to have IB ports
mlx4_core: Implement mechanism for reserved Q_Keys
net/mlx4_core: Free ICM table in case of error
IB/cm: Destroy idr as part of the module init error flow
mlx4_core: Remove double function declarations
IB/mlx4: Fill the masked_atomic_cap attribute in query device
IB/mthca: Fill in sq_sig_type in query QP
IB/mthca: Warning about event for non-existent QPs should show event type
IB/qib: Fix sparse RCU warnings in qib_keys.c
net/mlx4_core: Initialize IB port capabilities for all slaves
mlx4: Use port management change event instead of smp_snoop
IB/qib: RCU locking for MR validation
IB/qib: Avoid returning EBUSY from MR deregister
IB/qib: Fix UC MR refs for immediate operations
...
In its receive path, mlx4_en driver maps each page chunk that it pushes
to the hardware and unmaps it when pushing it up the stack. This limits
throughput to about 3Gbps on a Power7 8-core machine.
One solution is to map the entire allocated page at once. However, this
requires that we keep track of every page fragment we give to a
descriptor. We also need to work with the discipline that all fragments will
be released (in the sense that it will not be reused by the driver
anymore) in the order they are allocated to the driver.
This requires that we don't reuse any fragments, every single one of
them must be reallocated. We do that by releasing all the fragments that
are processed and only after finished processing the descriptors, we
start the refill.
We also must somehow guarantee that we either refill all fragments in a
descriptor or none at all, without resorting to giving up a page
fragment that we would have already given. Otherwise, we would break the
discipline of only releasing the fragments in the order they were
allocated.
This has passed page allocation fault injections (restricted to the
driver by using required-start and required-end) and device hotplug
while 16 TCP streams were able to deliver more than 9Gbps.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RFS infrastructure and flow steering in HW to keep CPU
affinity of rx interrupts and application per TCP stream.
A flow steering filter is added to the HW whenever the RFS
ndo callback is invoked by core networking code.
Because the invocation takes place in interrupt context, the
actual setup of HW is done using workqueue. Whenever new filter
is added, the driver checks for expiry of existing filters.
Since there's window in time between the point where the core
RFS code invoked the ndo callback, to the point where the HW
is configured from the workqueue context, the 2nd, 3rd etc
packets from that stream will cause the net core to invoke
the callback again and again.
To prevent inefficient/double configuration of the HW, the filters
are kept in a database which is indexed using hash function to enable
fast access.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable callers of mlx4_assign_eq to supply a pointer to cpu_rmap.
If supplied, the assigned IRQ is tracked using rmap infrastructure.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define this macro is one common place instead of duplicating it over the code
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereferenced "mclist" after the kfree().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be ">=" here instead of ">". MLX4_NET_TRANS_RULE_NUM is 6.
We use "spec->id" as an array offset into the __rule_hw_sz[] and
__sw_id_hw[] arrays which have 6 elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.
In addition, in SR-IOV mode, do the following:
1. Reduce reported P_Key table size by 1.
This is done to reserve the highest P_Key index for internal use,
for declaring an invalid P_Key in P_Key paravirtualization.
We require a P_Key index which always contain an invalid P_Key
value for this purpose (i.e., one which cannot be modified by
the subnet manager). The way to do this is to reduce the
P_Key table size reported to the subnet manager by 1, so that
it will not attempt to access the P_Key at index #127.
2. Paravirtualize the GID table size to 1. Thus, each guest sees
only a single GID (at its paravirtualized index 0).
In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify mlx4_dev_cap to allow IB support when SR-IOV is active. Modify
mlx4_slave_cap to set the "rdma-supported" bit in its flags area, and
pass that to the guests (this is done in QUERY_FUNC_CAP and its
wrapper).
However, we don't activate IB support quite yet -- we leave the error
return at the start of mlx4_ib_add in the mlx4_ib driver.
In addition, set "protected fmr supported" bit to zero in the
QUERY_FUNC_CAP wrapper.
Finally, in the QUERY_FUNC_CAP wrapper, we needed to add code which
checks for the port type (IB or Ethernet). Previously, this was not
an issue, since only Ethernet ports were supported.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The SR-IOV special QP tunneling mechanism uses proxy special QPs
(instead of the real special QPs) for MADs on guests. These proxy QPs
send their packets to a "tunnel" QP owned by the master. The master
then forwards the MAD (after any required paravirtualization) to the
real special QP, which sends out the MAD.
For security reasons (i.e., to prevent guests from sending MADs to
tunnel QPs belonging to other guests), each proxy-tunnel QP pair is
assigned a unique, reserved, Q_Key. These Q_Keys are available only
for proxy and tunnel QPs -- if the guest tries to use these Q_Keys
with other QPs, it will fail.
This patch introduces a mechanism for reserving a block of 64K Q_Keys
for proxy/tunneling use.
The patch introduces also two new fields into mlx4_dev: base_sqpn and
base_tunnel_sqpn.
In SR-IOV mode, the QP numbers for the "real," proxy, and tunnel sqps
are added to the reserved QPN area (so that they will not change).
There are 8 special QPs per port in the HCA, and each of them is
assigned both a proxy and a tunnel QP, for each VF and for the PF as
well in SR-IOV mode.
The QPNs for these QPs are arranged as follows:
1. The real SQP numbers (8)
2. The proxy SQPs (8 * (max number of VFs + max number of PFs)
3. The tunnel SQPs (8 * (max number of VFs + max number of PFs)
To support these QPs, two new fields are added to struct mlx4_dev:
base_sqp: this is the QP number of the first of the real SQPs
base_tunnel_sqp: this is the qp number of the first qp in the tunnel
sqp region. (On guests, this is the first tunnel
sqp of the 8 which are assigned to that guest).
In addition, in SR-IOV mode, sqp_start is the number of the first
proxy SQP in the proxy SQP region. (In guests, this is the first
proxy SQP of the 8 which are assigned to that guest)
Note that in non-SR-IOV mode, there are no proxies and no tunnels.
In this case, sqp_start is set to sqp_base -- which minimizes code
changes.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In mlx4_init_icm_table(), free the allocated table if we failed to
allocate memory to its entries.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Spotted four duplicate declarations in icm.h, remove them.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
With IB SR-IOV, each slave has its own separate copy of the port
capabilities flags. For example, the master can run a subnet manager
(which causes the IsSM bit to be set in the master's port
capabilities) without affecting the port capabilities seen by the
slaves (the IsSM bit will be seen as cleared in the slaves).
Also add a static inline mlx4_master_func_num() to enhance readability
of the code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The port management change event can replace smp_snoop. If the
capability bit for this event is set in dev-caps, the event is used
(by the driver setting the PORT_MNG_CHG_EVENT bit in the async event
mask in the MAP_EQ fw command). In this case, when the driver passes
incoming SMP PORT_INFO SET mads to the FW, the FW generates port
management change events to signal any changes to the driver.
If the FW generates these events, smp_snoop shouldn't be invoked in
ib_process_mad(), or duplicate events will occur (once from the
FW-generated event, and once from smp_snoop).
In the case where the FW does not generate port management change
events smp_snoop needs to be invoked to create these events. The flow
in smp_snoop has been modified to make use of the same procedures as
in the fw-generated-event event case to generate the port management
events (LID change, Client-rereg, Pkey change, and/or GID change).
Port management change event handling required changing the
mlx4_ib_event and mlx4_dispatch_event prototypes; the "param" argument
(last argument) had to be changed to unsigned long in order to
accomodate passing the EQE pointer.
We also needed to move the definition of struct mlx4_eqe from
net/mlx4.h to file device.h -- to make it available to the IB driver,
to handle port management change events.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, VFs have 0 in their dev->caps.function field. This is a
valid pci id (usually of the PF). Instead, pass an invalid PCI id to
the VF via QUERY_FW, so that if the value gets accessed in the VF
driver, we'll catch the problem.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The drop action is implemented by allocating a QP and keeping it in a reset state
such that the HW drops any packets which are steered to that QP. When a drop action
is requested, we attach the relevant flow to that QP.
Sign-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ethtool APIs for attaching L2/L3/L4 based flow steering
rules to the netdevice RX rings. Added set_rxnfc callback and enhanced
the existing get_rxnfc callback.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device managed flow steering API has three promiscuous modes:
1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.
Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with other device resources, the resource tracker is needed for supporting
device managed flow steering rules under SRIOV: make sure virtual functions
delete only rules created by them, and clean all rules attached by a crashed VF.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is modified to support three operation modes.
If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.
When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.
When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.
Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.
This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.
A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.
B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,
The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, for every change in the net device multicast list, the driver
detaches all the addresses from the HW device, and then attaches the
updated list. This behavior is wrong from two aspects: first, it causes
a load of firmware commands and second, there is period of time where
the correct addresses are not attached, which turned into packet loss.
To improve - a copy of the multicast list is saved by the driver. For
every change in the multicast list, the multicast list copy is used
to find the delta between those two lists and add or remove multicast
addresses as needed.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the IDs used by the resource tracker are of type u32, so far this was
ok since all the different resources we were tracking could be encoded in 32bit.
As a preparation step for tracking of resources whose IDs need > 32 bits such
as network flow steering rules, who are 64 bit in size, move to use 64 bit
based resource IDs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the data structure used for managing the SRIOV resource tracking
mechanism from radix tree to red-black tree. This is preparation step
for supporting resource IDs which are 64bit long, such as network flow
steering rules. Such IDs can't be used as radix-tree keys on 32bit
architectures and hence the reason for the change.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing resource release in ring cleanup.
Not doing this leaves a range of QPs that are being reserved,
and no one can use them.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a crash at the error flow of NOP command which caused the driver to try and use
a completion vector which wasn't allocated.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set valid port parameters: MTU and flow control configuration when
configuring the port during HW device initialization,
prior to the net device open() being called.
Using invalid parameters (such as all zeros)
could lead to bad firmware behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/route.c
This deals with a merge conflict between the net-next addition of the
inetpeer network namespace ops, and Thomas Graf's bug fix in
2a0c451ade which makes sure we don't
register /proc/net/ipv6_route before it is actually safe to do so.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 096335b3f9 ("mlx4_core: Allow dynamic MTU configuration for
IB ports") modifies the port VL setting. This exposes a bug in
mlx4_common_set_port(), where the VL cap value passed in (inside the
command mailbox) is incorrectly zeroed-out:
mlx4_SET_PORT modifies the VL_cap field (byte 3 of the mailbox).
Since the SET_PORT command is paravirtualized on the master as well as
on the slaves, mlx4_SET_PORT_wrapper() is invoked on the master. This
calls mlx4_common_set_port() where mailbox byte 3 gets overwritten by
code which should only set a single bit in that byte (for the reset
qkey counter flag) -- but instead overwrites the entire byte.
The result is that when running in SR-IOV mode, the VL_cap will be set
to zero -- fix this.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
A function in atl1e_main.c was passed a const pointer
when it actually modified elements of the structure.
Change the argument to a non-const pointer.
A function in stmmac needed a __force to avoid a sparse
warning. Added it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "!mlx4_is_slave" is totally confusing. Fix with
constant MLX4_CMD_NATIVE, which is the intended behavior.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range check was performed after using the port number.
Reverse this to prevent a potential array overflow.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- pass the following parameters:
- firmware version (added QUERY_FW paravirtualization for that)
- disable Blueflame on slaves. KVM disables write combining on guests,
and we get better performance without BF in this case. (This requires
QUERY_DEV_CAP paravirtualization, also in this commit)
- max qp rdma as destination
- get rid of a chunk of "if (0)" dead code
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port is used as an array index before we know if that is proper.
For example, in the catas event case, port is zero; however,
the port index should lie in the range (1..2).
Fix this by using 'port' only in the events where it is of interest.
Test for port out of range in the default (unhandled event) case,
and do not output a message if it is not an ethernet port.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV mode, the number of EQs used when computing the total ICM size
was incorrect.
To fix this, we do the following:
1. We add a new structure to mlx4_dev, mlx4_phys_caps, to contain physical HCA
capabilities. The PPF uses the phys capabilities when it computes things
like ICM size.
The dev_caps structure will then contain the paravirtualized values, making
bookkeeping much easier in SRIOV mode. We add a structure rather than a
single parameter because there will be other fields in the phys_caps.
The first field we add to the mlx4_phys_caps structure is num_phys_eqs.
2. In INIT_HCA, when running in SRIOV mode, the "log_num_eqs" parameter
passed to the FW is the number of EQs per VF/PF; each function (PF or VF)
has this number of EQs available.
However, the total number of EQs which must be allowed for in the ICM is
(1 << log_num_eqs) * (#VFs + #PFs). Rather than compute this quantity,
we allocate ICM space for 1024 EQs (which is the device maximum
number of EQs, and which is the value we place in the mlx4_phys_caps structure).
For INIT_HCA, however, we use the per-function number of EQs as described
above.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ths fixes the comparison in the FLR (Function Level Reset) event case.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yWfr
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.
* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
IB/mlx4: Fix mlx4_ib_add() error flow
IB/core: Fix IB_SA_COMP_MASK macro
IB/iser: Fix error flow in iser ep connection establishment
IB/mlx4: Increase the number of vectors (EQs) available for ULPs
RDMA/cxgb4: Add query_qp support
RDMA/cxgb4: Remove kfifo usage
RDMA/cxgb4: Use vmalloc() for debugfs QP dump
RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
RDMA/cxgb4: Add DB Overflow Avoidance
RDMA/cxgb4: Add debugfs RDMA memory stats
cxgb4: DB Drop Recovery for RDMA and LLD queues
cxgb4: Common platform specific changes for DB Drop Recovery
cxgb4: Detect DB FULL events and notify RDMA ULD
RDMA/cxgb4: Drop peer_abort when no endpoint found
RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
mlx4_core: Change bitmap allocator to work in round-robin fashion
RDMA/nes: Don't call event handler if pointer is NULL
RDMA/nes: Fix for the ORD value of the connecting peer
...
Change the TX ring scheme such that the number of rings for untagged packets
and for tagged packets (per each of the vlan priorities) is the same, unlike
the current situation where for tagged traffic there's one ring per priority
and for untagged rings as the number of core.
Queue selection is done as follows:
If the mqprio qdisc is operates on the interface, such that the core networking
code invoked the device setup_tc ndo callback, a mapping of skb->priority =>
queue set is forced - for both, tagged and untagged traffic.
Else, the egress map skb->priority => User priority is used for tagged traffic, and
all untagged traffic is sent through tx rings of UP 0.
The patch follows the convergence of discussing that issue with John Fastabend
over this thread http://comments.gmane.org/gmane.linux.network/229877
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Liran Liss <liranl@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing resource tracking for XRC domains and complete the tracking for HCA
network flow counters.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the slave and master resources are deleted after master freed
all bitmaps. If any resources were not properly cleaned up during the
shutdown process, an Oops would result.
Fix so that delete slave (only) resources during cleanup. Master resources
are cleaned up during unload process, and need not separately be cleaned.
Note that during cleanup, we need to split the resource-tracker freeing
functionality.
Before removing all the bitmaps, we free any leftover slave resources.
However, we can only remove the resource tracker linked list after
all bitmap frees, since some of the freeing functions (e.g.,
mlx4_cleanup_eq_table) use paravirtualized FW commands which expect
the resource tracker linked list to be present.
Found-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following scenario: 2 HCAs, where only one of which can run SRIOV.
If we reset the module parameter, all the VFs of the SRIOV HCA will be
claimed by the PPF host (-- the code relies on num_vfs being non-zero
to avoid this claiming, and num_vfs was reset when pci_enable_sriov failed
for the non-SRIOV HCA).
The solution is not to touch the num_vfs parameter.
Also, eliminate the unneeded check of num_vfs when disabling sriov
(the dev flag bit is sufficient).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed unsued *_str helper functions from resource_tracker.c
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "wrapped" was incorrect, since no wrapper function was defined.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mlx4_INIT_PORT_wrapper, the port state mask for the
slave is only set if we are invoking the INIT_PORT fw command.
However, the reference count for the (initialized) port is
incremented anyway.
This creates a problem in that when we have multiple slaves,
then the CLOSE_PORT command will never be invoked. The
reason is that in the CLOSE_PORT wrapper, if the port-state
mask is zero for the slave (which it is), the wrapper returns
without doing anything. The only slave which will not return
immediately in the CLOSE_PORT wrapper is that slave for which
INIT_PORT was invoked.
The fix is to not have the port-state mask setting depend
on the logic for calling the INIT_PORT fw command.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the compiler warnings on variables which are set but not used
by removing the relevant variable or casting a return value which is
ignored on purpose to void.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under most circumstances, the bitmap allocator does not allocate the
same full 24-bit QP number immediately after a QP is destroyed.
This works by using the upper bits of a 24-bit QP number, beyond the
number of QPs that are actually available in the low level driver.
For example, say that the HCA is willing to allocate a maximum of 64K
qps. We use the bits 23..16 as a "counter" which is incremented by 1
at each allocation so that even if the same physical QP is
re-allocated, it will not receive the same 24-bit QP number.
However, we have seen the following scenario:
1. Allocate, say, 255 QPs in succession. This will cause a wrap of the "counter".
2. Destroy the first QP allocated, then allocate a new QP. The new QP,
because of the counter wraparound, will get the same FULL QP number as
the QP just destroyed!
This is a problem because packets in transit can be erroneously
delivered to the new QP when they were meant for the old (destroyed)
QP, because the full QP number of the new QP is identical to the
destroyed QP. (The "counter" mechanism is meant to prevent this by
having the full 24-bit QP numbers differ even if the physical QP on
the HCA is the same. As we see above, however, this mechanism does
not always work).
The best fix for this problem is to allocate QPs in round-robin mode,
so that the physical QP numbers are not immediately re-used.
Found-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds a 64-bit flags2 features member to struct mlx4_dev to
export further features of the hardware. The original flags field
tracks features whose support bits are advertised by the firmware in
offsets 0x40 and 0x44 of the query device capabilities command.
flags2 will track features whose support bits are scattered at various
offsets.
RSS support is the first feature to be exported through flags2. RSS
capabilities are located at offset 0x2e. The size of the RSS
indirection table is also given in this offset.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Moving to interrupts instead of polling fpr TX completions
Avoiding situations where skb can be held in by the driver for
a long time (till timer expires).
The change is also necessary for supporting BQL.
Removing comp_lock that was required because we could handle TX
completions from several contexts: Interrupts, timer, polling.
Now there is only interrupts
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 109d244605
"net/mlx4_en: Set max rate-limit for a TC"
introduced 64 bit math operations into mlx4_en_dcbnl_ieee_setmaxrate()
causing the following final link failure on an x86_32 allmodconfig
ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx4/mlx4_en.ko] undefined!
Convert it to use div_u64() instead.
Cc: Amir Vadai <amirv@mellanox.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is using the DCB netlink to set rate limit per ETS TC
Values are accepted in Kbps and rounded up to the nearest multiply of 100Mbps.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since vlan egress map is only good for tagged traffic, need to have other
mapping to be used by untagged traffic.
For that, the driver uses sch_mqprio mapping. This mapping could be set by
using tc tool from iproute2 package.
Mapped UP will be used by the HW for QoS purposes, but won't go out on the
wire.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set TSA, promised BW and PFC using IEEE 802.1qaz netlink commands.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding QoS firmware commands:
- mlx4_en_SET_PORT_PRIO2TC - set UP <=> TC
- mlx4_en_SET_PORT_SCHEDULER - set promised BW, max BW and PG number
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on HW to change schedule queue by UP, schedule
queue is fixed for a tx_ring, and UP in WQE is ignored in this aspect. This
resolves two issues with untagged traffic:
1. untagged traffic has no UP in packet which is needed for QoS. The change
above allows setting the schedule queue (and by that the UP) of such a stream.
2. BlueFlame uses the same field used by vlan tag. So forcing UP from QPC
allows using BF for untagged but prioritized traffic.
In old firmware that force UP is not supported, untagged traffic will not subject to
QoS.
Because UP is set by QP, need to always have a tx ring per UP, even if pfcrx
module paramter is false.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a 2-order allocation, which is too much on architectures
like ppc64, which has a 64KiB page. This particular allocation is used
for large packet fragments that may have a size of 512, 1024, 4096 or
fill the whole allocation. So, a minimum size of 16384 is good enough
and will be the same size that is used in architectures of 4KiB sized
pages.
This will avoid allocation failures that we see when the system is under
stress, but still has plenty of memory, like the one below.
This will also allow us to set the interface MTU to higher values like
9000, which was not possible on ppc64 without this patch.
Node 1 DMA: 737*64kB 37*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 51904kB
83137 total pagecache pages
0 pages in swap cache
Swap cache stats: add 0, delete 0, find 0/0
Free swap = 10420096kB
Total swap = 10420096kB
107776 pages RAM
1184 pages reserved
147343 pages shared
28152 pages non-shared
netstat: page allocation failure. order:2, mode:0x4020
Call Trace:
[c0000001a4fa3770] [c000000000012f04] .show_stack+0x74/0x1c0 (unreliable)
[c0000001a4fa3820] [c00000000016af38] .__alloc_pages_nodemask+0x618/0x930
[c0000001a4fa39a0] [c0000000001a71a0] .alloc_pages_current+0xb0/0x170
[c0000001a4fa3a40] [d00000000dcc3e00] .mlx4_en_alloc_frag+0x200/0x240 [mlx4_en]
[c0000001a4fa3b10] [d00000000dcc3f8c] .mlx4_en_complete_rx_desc+0x14c/0x250 [mlx4_en]
[c0000001a4fa3be0] [d00000000dcc4eec] .mlx4_en_process_rx_cq+0x62c/0x850 [mlx4_en]
[c0000001a4fa3d20] [d00000000dcc5150] .mlx4_en_poll_rx_cq+0x40/0x90 [mlx4_en]
[c0000001a4fa3dc0] [c0000000004e2bb8] .net_rx_action+0x178/0x450
[c0000001a4fa3eb0] [c00000000009c9b8] .__do_softirq+0x118/0x290
[c0000001a4fa3f90] [c000000000031df8] .call_do_softirq+0x14/0x24
[c000000184c3b520] [c00000000000e700] .do_softirq+0xf0/0x110
[c000000184c3b5c0] [c00000000009c6d4] .irq_exit+0xb4/0xc0
[c000000184c3b640] [c00000000000e964] .do_IRQ+0x144/0x230
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Tested-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stands out; by patch count lots of fixes to the mlx4 driver plus some
cleanups and fixes to the core and other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DbLx
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes for the 3.4 merge window from Roland Dreier:
"Nothing big really stands out; by patch count lots of fixes to the
mlx4 driver plus some cleanups and fixes to the core and other
drivers."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (28 commits)
mlx4_core: Scale size of MTT table with system RAM
mlx4_core: Allow dynamic MTU configuration for IB ports
IB/mlx4: Fix info returned when querying IBoE ports
IB/mlx4: Fix possible missed completion event
mlx4_core: Report thermal error events
mlx4_core: Fix one more static exported function
IB: Change CQE "csum_ok" field to a bit flag
RDMA/iwcm: Reject connect requests if cmid is not in LISTEN state
RDMA/cxgb3: Don't pass irq flags to flush_qp()
mlx4_core: Get rid of redundant ext_port_cap flags
RDMA/ucma: Fix AB-BA deadlock
IB/ehca: Fix ilog2() compile failure
IB: Use central enum for speed instead of hard-coded values
IB/iser: Post initial receive buffers before sending the final login request
IB/iser: Free IB connection resources in the proper place
IB/srp: Consolidate repetitive sysfs code
IB/srp: Use pr_fmt() and pr_err()/pr_warn()
IB/core: Fix SDR rates in sysfs
mlx4: Enforce device max FMR maps in FMR alloc
IB/mlx4: Set bad_wr for invalid send opcode
...
Prevent race condition between commands on comm channel.
Happened while unloading the driver when switching from
event to polling mode. VF got completion on the last command
before switching to polling mode, but toggle was not changed.
After the fix - VF will not write the next command before
toggle is updated.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver defaults to 1M MTT segments, where each segment holds
8 MTT entries. This limits the total memory registered to 8M * PAGE_SIZE
which is 32GB with 4K pages. Since systems that have much more memory
are pretty common now (at least among systems with InfiniBand hardware),
this limit ends up getting hit in practice quite a bit.
Handle this by having the driver allocate at least enough MTT entries to
cover 2 * totalram pages.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the MTU for IB ports in the driver instead of using the firmware
default of 2KB (the driver defaults to 4KB). Allow for dynamic mtu
configuration through a new, per-port sysfs entry.
Since there's a dependency between the port MTU and the max number of
HW VLs the port can support, apply a mim/max approach, using a loop
that goes down from the highest possible number of VLs to the lowest,
using the firmware return status to know whether the requested number
of VLs is possible with a given MTU.
For now, as with the dynamic link type change / VPI support, the sysfs
entry to change the mtu is exposed only when NOT running in SR-IOV
mode. To allow changing the MTU for the master in SR-IOV mode,
primary-function-initiated FLR (Function Level Reset) needs to be
implemented.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Print an error message when a thermal error async event is reported by the HW.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Dotan Barak <dotanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 22c8bff6fa ("mlx4_core: Exported functions can't be static")
fixed most of this up, but forgot about mlx4_is_slave_active(). Fix
this one too.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The actual FW command is called in procedure "handle_resize".
Code incorrectly invoked the FW command again (in good flow), in
the modify_cq wrapper function.
Fix by skipping second FW invocation unconditionally for resize.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing the work for commit a6f7feae6d ("IB/mlx4: pass SMP
vendor-specific attribute MADs to firmware") we realized that the
firmware would respond on all sorts of vendor-specific MADs.
Therefore commit 97285b7817 ("mlx4_core: Add extended port
capabilities support") adds redundant code into the driver, since
there's no real reaon to maintain the extended capabilities of the
port, as they can be queried on demand (e.g the FDR10 capability).
This patch reverts commit 97285b7817 and removes the check for
extended caps from the mlx4_ib driver port query flow.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fixing sparse warnings, the 2 functions are only used in same
file. Defining them as static and not exporting them.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing functions that are no longer in use, but still exist
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SET_PORT functions are implemented in port.c, which is part
of mlx4_core, these functions are exported. The functions are in use by
the mlx4_en module (were originally part of mlx4_en).
Their declaration remained in mlx4_en module, moving the declaration to the right location.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac should be written as __be64 the gid. The warning was because
we changed the mac parameter, which is u64, by writing result of cpu_to_be64
into it. Fixing by using new variable of type __be64.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keys used for the hardware RSS topelitz hash are of type __be32
where the values provided by the driver are from array of u32,
this triggered sparse warning on incorrect type in assignment as of different base types.
Since these values are picked randomly,
the fix is to transform the key to __be32 by executing cpu_to_be_32()
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blue flame buffer is defined to be of type void __iomem *
but was passed to mlx4_bf_copy which gets unsigned long * .
This triggered sparse warning on different address spaces,
fix that by changing mlx4_bf_copy first param to be of type void __iomem * .
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings on incompatibility between the endianess of the ctrl_flags
field of struct mlx4_en_priv to the srcrb_flags field of struct
mlx4_wqe_ctrl_seg by changing the former to be __be32 instead of u32.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Localized the pdev->dev, and using dma_map instead of pci_map
There are multiple map/unmap operations on data path,
optimizing those by saving redundant pointer access.
Those places were identified as hot-spots when running kernel profiling
during some benchmarks.
The fixes had most impact when testing packet rate with small packets,
reducing several % from CPU load, and in some case being the difference
between reaching wire speed or being CPU bound.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a bug introduced by commit fe9a2603c, where the priority bits
in the schedule queue field were masked out.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new sparse errors introduced in commit 6221217199 (mlx4_en: dont
change mac_header on xmit)
Reported-by: Or Gerlitz <or.gerlitz@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) ICMP sockets leave err uninitialized but we try to return it for the
unsupported MSG_OOB case, reported by Dave Jones.
2) Add new Zaurus device ID entries, from Dave Jones.
3) Pointer calculation in hso driver memset is wrong, from Dan
Carpenter.
4) ks8851_probe() checks unsigned value as negative, fix also from Dan
Carpenter.
5) Fix crashes in atl1c driver due to TX queue handling, from Eric
Dumazet. I anticipate some TX side locking fixes coming in the near
future for this driver as well.
6) The inline directive fix in Bluetooth which was breaking the build
only with very new versions of GCC, from Johan Hedberg.
7) Fix crashes in the ATP CLIP code due to ARP cleanups this merge
window, reported by Meelis Roos and fixed by Eric Dumazet.
8) JME driver doesn't flush RX FIFO correctly, from Guo-Fu Tseng.
9) Some ip6_route_output() callers test the return value for NULL, but
this never happens as the convention is to return a dst entry with
dst->error set. Fixes from RonQing Li.
10) Logitech Harmony 900 should be handled by zaurus driver not
cdc_ether, update white lists and black lists accordingly. From
Scott Talbert.
11) Receiving from certain kinds of devices there won't be a MAC header,
so there is no MAC header to fixup in the IPSEC code, and if we try
to do it we'll crash. Fix from Eric Dumazet.
12) Port type array indexing off-by-one in mlx4 driver, fix from Yevgeny
Petrilin.
13) Fix regression in link-down handling in davinci_emac which causes
all RX descriptors to be freed up and therefore RX to wedge
completely, from Christian Riesch.
14) It took two attempts, but ctnetlink soft lockups seem to be
cured now, from Pablo Neira Ayuso.
15) Endianness bug fix in ENIC driver, from Santosh Nayak.
16) The long ago conversion of the PPP fragmentation code over to
abstracted SKB list handling wasn't perfect, once we get an
out of sequence SKB we don't flush the rest of them like we
should. From Ben McKeegan.
17) Fix regression of ->ip_summed initialization in sfc driver.
From Ben Hutchings.
18) Bluetooth timeout mistakenly using msecs instead of jiffies,
from Andrzej Kaczmarek.
19) Using _sync variant of work cancellation results in deadlocks,
use the non _sync variants instead. From Andre Guedes.
20) Bluetooth rfcomm code had reference counting problems leading
to crashes, fix from Octavian Purdila.
21) The conversion of netem over to classful qdisc handling added
two bugs to netem_dequeue(), fixes from Eric Dumazet.
22) Missing pci_iounmap() in ATM Solos driver. Fix from Julia Lawall.
23) b44_pci_exit() should not have __exit tag since it's invoked from
non-__exit code. From Nikola Pajkovsky.
24) The conversion of the neighbour hash tables over to RCU added a
race, fixed here by adding the necessary reread of tbl->nht, fix
from Michel Machado.
25) When we added VF (virtual function) attributes for network device
dumps, this potentially bloats up the size of the dump of one
network device such that the dump size is too large for the buffer
allocated by properly written netlink applications.
In particular, if you add 255 VFs to a network device, parts of
GLIBC stop working.
To fix this, we add an attribute that is used to turn on these
extended portions of the network device dump. Sophisticaed
applications like 'ip' that want to see this stuff will be changed
to set the attribute, whereas things like GLIBC that don't care
about VFs simply will not, and therefore won't be busted by the
mere presence of VFs on a network device.
Thanks to the tireless work of Greg Rose on this fix.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
sfc: Fix assignment of ip_summed for pre-allocated skbs
ppp: fix 'ppp_mp_reconstruct bad seq' errors
enic: Fix endianness bug.
gre: fix spelling in comments
netfilter: ctnetlink: fix soft lockup when netlink adds new entries (v2)
Revert "netfilter: ctnetlink: fix soft lockup when netlink adds new entries"
davinci_emac: Do not free all rx dma descriptors during init
mlx4_core: Fixing array indexes when setting port types
phy: IC+101G and PHY_HAS_INTERRUPT flag
netdev/phy/icplus: Correct broken phy_init code
ipsec: be careful of non existing mac headers
Move Logitech Harmony 900 from cdc_ether to zaurus
hso: memsetting wrong data in hso_get_count()
netfilter: ip6_route_output() never returns NULL.
ethernet/broadcom: ip6_route_output() never returns NULL.
ipv6: ip6_route_output() never returns NULL.
jme: Fix FIFO flush issue
atm: clip: remove clip_tbl
ipv4: ping: Fix recvmsg MSG_OOB error handling.
rtnetlink: Fix problem with buffer allocation
...
A driver xmit function is not allowed to change skb without special
care.
mlx4_en_xmit() should not call skb_reset_mac_header() and instead should
use skb->data to access ethernet header.
This removes a dumb test : if (ethh && ethh->h_dest)
Also remove this slow mlx4_en_mac_to_u64() call, we can use
get_unaligned() to get faster code.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
ConnectX devices have a limit on the number of mappings that can be
done on an FMR before having to call sync_tpt. The current
mlx4_ib driver reports the limit correctly in max_map_per_fmr in
.query_device(), but mlx4_core doesn't check it when actually
allocating FMRs.
Add a max_fmr_maps field to struct mlx4_caps and enforce this maximum
value on FMR allocations.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
At least on powerpc, it breaks the build if exported functions are
static. Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In port type change flow, need to set the new port types only after
all interfaces have finished the unregister process.
Otherwise, during unregister, one of the interfaces might issue a SET_PORT
command with wrong port types, it can cause bad FW behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under the spinlock we call request_irq(), which allocates memory with GFP_KERNEL,
This causes the following trace when DEBUG_SPINLOCK is enabled, it can cause
the following trace:
BUG: spinlock wrong CPU on CPU#2, ethtool/2595
lock: ffff8801f9cbc2b0, .magic: dead4ead, .owner: ethtool/2595, .owner_cpu: 0
Pid: 2595, comm: ethtool Not tainted 3.0.18 #2
Call Trace:
spin_bug+0xa2/0xf0
do_raw_spin_unlock+0x71/0xa0
_raw_spin_unlock+0xe/0x10
mlx4_assign_eq+0x12b/0x190 [mlx4_core]
mlx4_en_activate_cq+0x252/0x2d0 [mlx4_en]
? mlx4_en_activate_rx_rings+0x227/0x370 [mlx4_en]
mlx4_en_start_port+0x189/0xb90 [mlx4_en]
mlx4_en_set_ringparam+0x29a/0x340 [mlx4_en]
dev_ethtool+0x816/0xb10
? dev_get_by_name_rcu+0xa4/0xe0
dev_ioctl+0x2b5/0x470
handle_mm_fault+0x1cd/0x2d0
sock_do_ioctl+0x5d/0x70
sock_ioctl+0x79/0x2f0
do_vfs_ioctl+0x8c/0x340
sys_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
Replacing with mutex, which is enough in this case.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
BF can be disabled in some cases, the capability field, bf_reg_size is set
to zero in this case. Don't map the BF area in this case, it would cause
failures. In addition, leaving the BF area unmapped
also alerts the ETH driver to not use BF.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@melllanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_multicast_attach/detach() should use always MLX4_MC_STEER flag
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_uc_steer_add/release() should not add MLX4_UC_STEER flag to gid.
It is added in mlx4_unicast_attach/detach().
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_qp_attach/detach_common() don't use hash variable, move it to find_entry()
static find_entry() in mcg.c doesn't use steer argument
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary field high_prios from mlx4_steer struct and initialization
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@melllanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_prepare_rx_desc does not correctly clean up after it finds an
allocation failure. It should unmap a page before calling put_page, but
it only calls the later.
This bug would prevent a device removal using hotplug after setting the
device MTU to 9000 and opening the network interface. After the fix, we
still see the allocation failure with MTU 9000, but we are able to
remove the device.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After opening the network interface, Mellanox ConnectX device cannot be
removed by hotplug because it has not properly unmapped all DMA memory.
It happens that mlx4_en_activate_rx_rings overrides the variable that
keeps the size of the memory mapped.
This is fixed by passing to mlx4_en_destroy_rx_ring the same size that is
given to mlx4_en_create_rx_ring.
After applying this patch, hot unplugging the device works after opening
the interface.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use port number for correct steering (list per port).
Before the fix all steering entries (for both physical ports)
were managed in first port structures, so we had leakage of resources
for port 2.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MLX4_DEV_CAP_FLAG_VEP_UC_STEER for unicast_promisc_add/remove
Unicast entries were managed in wrong data structures.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform cleanup also in non-master flow.
The VFs use communication channel as well.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling "reseting" to "resetting" in
drivers/net/ethernet/mellanox/mlx4/cmd.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slave async events were mapped to single eq. This patch fixes this issue, so
the slaves can map the async events to any eq.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Num mtts from profile is really the number of mtt segments.
Thus, in make profile, to get the proper number of MTT entries,
must multiply num_mtts by mtts per segment.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Virtual Functions should not be aware their function number.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In native mode display all available staticstics.
In SRIOV mode on VF display only SW counters statistics,
in SRIOV mode on hypervisor display SW counters and errors (got from FW)
statistics.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multifunction mode - DUMP_STATS command is not executed
for VFs.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Not all stats fields were cleared.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petriln <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value must be a power of 2 due to HW limitation.
Driver supports only 'equal' mode in ethtool and can't be set by using weights.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Showing which capabilities are not passed to VF
when executing QUERY_PORT
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mtt range was allocated in mtt units but deallocated
in segments. Among the rest, this caused crash during hotplug removal
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caused loss of connectivity when changing ring size.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment VFs can only operate in Eth mode.
In addition we don't want the VF to attempt link sensing,
so we block this option as well.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include linux/slab.h to fix below build error:
CC drivers/net/ethernet/mellanox/mlx4/resource_tracker.o
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_init_resource_tracker':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:233: error: implicit declaration of function 'kzalloc'
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:234: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_free_resource_tracker':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:264: error: implicit declaration of function 'kfree'
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_qp_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:370: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_mtt_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:386: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_mpt_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:402: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_eq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:417: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_cq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:431: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_srq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:446: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_counter_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:461: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'add_res_range':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:521: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mac_add_to_slave':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:1193: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'add_mcg_res':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:2521: warning: assignment makes pointer from integer without a cast
make[5]: *** [drivers/net/ethernet/mellanox/mlx4/resource_tracker.o] Error 1
make[4]: *** [drivers/net/ethernet/mellanox/mlx4] Error 2
make[3]: *** [drivers/net/ethernet/mellanox] Error 2
make[2]: *** [drivers/net/ethernet] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When UDP RSS is enabled, we use same QPN for TCP and UDP ranges
The bug is that the default_qpn was used base UDP qpn before it
was set.
Fixes bug introduced in commit: 1202d460b1
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
(Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The communication channel is HW interface from PF point of view
So the command return status should be stored as HW error code
and only then translated to errno values.
Reporetd-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is always called from irq context, changing the call
to spin_lock().
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Solves an issue where we tried to free the same page twice after
the port has been opened and closed.
Signed-off-by: Alexander Guller <alexg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.
2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
IB or Ethernet.
The driver will use this hint in case the user didn't specify explicitly the link layer
type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
and default the port to link sensing
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ConnectX3 devices, we allow link sensing only if FW explicitly
reported it supports the feature.
For older versions (ConnectX1 and 2), if the card supports both link layer types
(Ethenet and Infiniband), link sensing is supported.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a compile error that occurs when the driver
is compile into the kernel and not as a module.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added module parameters sr_iov and probe_vf for controlling enablement of
SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
ports configured as desired.
In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
for the case where the FW supports both port types (ETH and IB), the
port_type_array parameter is used.
By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
VFs obtain their startup information from the PF (master) device via the
comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership: Currently, only one PF is supported by the driver.
If the HCA is burned with FW which enables more than one PF, only one
of the PFs is allowed to run. The first one up grabs a FW ownership
semaphone -- all other PFs will find that semaphore taken, and the
driver will not allow them to run.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in SRIOV mode, driver should not automatically start/stop
the mlx4_core upon sensing an HCA internal error -- doing this disables/enables
sriov, which will cause the hypervisor to hang if there are running VMs with
attached VFs.
In addition, on VMs the catas process should not run at all, since the HCA
error buffer is not available to VMs in the BARs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implementation mtts are managed by:
1. order - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order - log(mtts) rather than segments
2. offset - mtt index in mtt table
Note: The actual mtt allocation is made in segments but it is
transparent to callers.
Rational: The mtt resource holders are not interested on how the allocation
of mtt is done, but rather on how they will use it.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable internal loopback, always fill DMAC in control segment
when transmitting the packet, once this is done, the packet is subject
for loopback for if the DMAC mathces one of the multicast/unicast addresses
registered on the physical port.
In receive path if source MAC is our own MAC and we are not in selftest,
or not in force LB mode - drop this packet.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware
Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let multicast/unicast attaching flow go through resource tracker.
The PF is the one responsible for managing all the steering entries.
Define and use module parameter that determines the number of qps
per multicast group.
Minor changes in function calls according to changed prototype.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The resource tracker is used to track usage of HCA resources by the different
guests.
Virtual functions (VFs) are attached to guest operating systems but
resources are allocated from the same pool and are assigned to VFs. It is
essential that hostile/buggy guests not be able to affect the operation of
other VFs, possibly attached to other guest OSs since ConnectX firmware is not
tolerant to misuse of resources.
The resource tracker module associates each resource with a VF and maintains
state information for the allocated object. It also defines allowed state
transitions and enforces them.
Relationships between resources are also referred to. For example, CQs are
pointed to by QPs, so it is forbidden to destroy a CQ if a QP refers to it.
ICM memory is always accessible through the primary function and hence it is
allocated by the owner of the primary function.
When a guest dies, an FLR is generated for all the VFs it owns and all the
resources it used are freed.
The tracked resource types are: QPs, CQs, SRQs, MPTs, MTTs, MACs, RES_EQs,
and XRCDNs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing async events to slaves:
In SRIOV mode, each slave creates its own async EQ, but only the master can
register directly with the FW to receive async events. Async events which
should be passed to slaves (such as a WQ_ACCESS_ERROR for a QP owned by a slave)
are generated at the slave by the master using the GEN_EQE FW command.
Wrapper functions: mlx4_MAP_EQ_wrapper
Only the master can map an EQ. The slave commands to map their EQs arrive
at the master via the comm channel. The master then invokes the wrapper
function to do the work (and enter the resource in the tracking database).
New events: COMM_CHANNEL and FLR
The COMM_CHANNEL event arrives only at the master, and signals that
a slave has posted a command on the comm channel.
The FLR event is generated by the FW when a guest operating a VF
unexpectedly goes down.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTTs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
CQs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
QPs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
SRQs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commands are added here:
1. QUERY_FUNC_CAP and its wrapper. This function is used by VFs when
they start up to receive configuration information from the PF, such
as resource quotas for this VF, which ports should be used (currently
two), what protocol is running on the port (currently Ethernet ONLY,
or port not active).
2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly
by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now
required here (the VF's MAC address must be substituted for the PFs
MAC address returned by the FW). We changed the invocation
in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper.
3. QUERY_HCA. Used by the VF to determine how the HCA was initialized.
For now, we need only the multicast table member entry size
(log2_mc_table_entry_sz, in the ConnectX PRM). No wrapper is needed
here, because the data may be passed as is to the VF without modification).
In this command, we have added a GLOBAL_CAPS field for passing required
configuration information from FW to a VF (this field is to allow safely
adding new SRIOV capabilities which require support in VF drivers, too).
Bits will set here by FW in response to PF-driver configuration commands which
will activate as yet undefined new SRIOV features. The VF will test to see that
all required capabilities indicated by this field are supported (i.e., if a bit
is set and the VF driver does not recognize that bit, it must abort
its initialization). Currently, no bits are set.
4. Added a CLOSE_PORT wrapper. The PF context needs to keep track of how many VF contexts
have the port open. The PF context will not actually issue the FW close port command
until the last port user issues a CLOSE_PORT request.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SRIOV is enabled, pf and vfs communicate via shared comm channel.
The vf gets its side of the comm channel via a VF BAR.
Each VF (slave) creates its vHCR (virtual HCA Command Register),
Its DMA address is passed to the PF (master) using Communication Channel Register.
The same Register is used to notify the master of commands posted by the
slaves and for the master to pass events to the slaves, such as command completions
and asynchronous events.
The vHCR format is identical to the HCR format, except for the 'go' and 't' bits,
which are reserved in the vHCR. Posting commands to the vHCR is identical to
the way it is done with the HCR, albeit that the function/PF token fields are
used instead of the HCR go bit.
Specifically:
- When the function prepares a new command in the vHCR, it issues the Post_vHCR_cmd
communication channel command and toggles the value of the function token;
when PF token has an equal value, the command has been accepted and a new command may be posted.
- When the PF detects a Post_vHCR_cmd command, it concludes that a new command is available in the vHCR;
after processing the command, the PF toggles the PF token to match the function token.
When the 'e' bit is not set, the completion of a Post_vHCR_cmd command also indicates
the completion the vHCR command. If, however, the 'e' bit is set, the completion of a
Post_vHCR_cmd command only indicates that the vHCR command has been accepted for execution by the PF.
Function commands are processed by the PF as follows:
-DMA (using the ACCESS_MEM command) the vHCR image into a shadow buffer.
-Validate that the opcode is non-privileged, and that the opcode- and input-modifiers are legal.
-DMA the in-box (if required) into a shadow buffer.
-Validate the command:
o Resource ranges (e.g., QP ranges).
o Partition key.
o Ranges of referenced resources (e.g., CQs within QP contexts).
-If the 'e' bit is set
o complete the Post_vHCR_cmd command
-Execute the command on the HCR.
-DMA the results to the vHCR out-box (if required).
-If the 'e' bit is set
o Indicate command completion by generating a completion event using the GEN_EQE command
-Otherwise
o DMA the command status to the vHCR
o Complete the Post_vHCR_cmd command
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrillin <yevgenyp@mellanox.com>
Signed-off-by: Liran Liss <liranl@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SRIOV is enabled on the chip (at FW burning time),
the HCA uses only 17 bits for the PD. The remaining 7 high-order bits
are ignored.
Change the allocator to return only 17 bits for the PD. The MSB 7
bits will be used to encode the slave number for consistency
checking later on in the resource tracker.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).
This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.
Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mask now has additional state.
Port can be set as "none". In this case neither the mlx4_en or mlx4_ib
drivers take ownership of the port.
In multifunction mode there is an option to set the vfs as single ported devices.
(in single function mode, both physical ports belong to same function)
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
These changes will not affect module operation as yet. They
are only to get some structs and enums in place for use by
subsequent patches (making those smaller).
Added here:
* sriov state structs and inlines (mlx4_is_master/slave/mfunc)
* comm-channel and vhcr support structures
* enum values for new FW and comm-channel virtual commands
(i.e., commands, passed via the comm channel to the PF-driver).
* prototypes for many command wrapper functions (used by the
PF context for processing FW commands passed to it by the VFs).
* struct mlx4_eqe is moved from eq.c to mlx4.h (it will be used
by other mlx4_core source files).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using vlan 0 and UP 0, vlan header wasn't placed.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device must be in promiscuous mode or DMAC must be same as the host MAC, or
else packet will be dropped by the HW rx filtering.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 capability bits for WOL, one for each port.
WOL handlers were looking only on the second bit, regardless of the port.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving to regular Completion Queue implementation (not collapsed)
Completion for each transmitted packet is written to new entry.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
the MLX4_EN_WOL_DO_MODIFY flag which is defined through enum targets
bit 63, this triggers a "cast truncate bits from constant value
(8000000000000000 becomes 0)" warning from sparse, fix that by using
define instead of enum.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using RSS which takes into account UDP headers is controlled by
a module param, fix the setting of the HW RSS context to align
with that scheme. So far it was uncoditionally allowing hashing
on the UDP headers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Towards adding RSS support for IB drivers/application who use
the mlx4 HW, make the RSS related definitions global and change
the mlx4_en driver to use them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
When HW doesn't remove FCS bytes they are reported in the completion
byte count, we don't need to take them to skb.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This round of floor sweeping converts strncpy calls in various .get_drvinfo
routines to the preferred strlcpy. It also does a modicum of other
cleaning in those routines.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
These files were using moduleparam infrastructure, but were not
including anything for it -- which is fine when module.h is being
implicitly included in all files, but that is going away.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c
This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
skb->truesize must account for allocated memory, not the used part of
it. Doing this work is important to avoid unexpected OOM situations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving to Toeplitz function in RSS calculation.
Reporting rxhash in skb.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not updating common counters from data path.
The checksum counters are per ring, summarizing them when collecting statistics.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Canceling FCS removal where FW allows for better alignment
of incoming data.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent overflow when trying to register more Vlans then the Vlan table in
HW is configured to.
Need to take into acount that the first 2 entries are reserved.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query port will now identify a 40G Ethernet speed.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdevice was being freed without being unregistered first if
mlx4_SET_PORT_general or mlx4_INIT_PORT failed.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of bits taken from mac table index in QP
calculation should be based on log_num_mac parameter.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a memory leak caused by missing iounmap when device
is being released.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Sharon Cohen <sharonc@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moderation is now done per ring and coalescing is enabled
by set_ring_param in ethtool.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug where ring size change caused insufficient memory
upon driver restart due to unreleased EQs.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now only RX rings used irq per ring
and TX used only one per port.
>From now on, both of them will use the
irq per ring while RX & TX ring[i] will
use the same irq.
Signed-off-by: Alexander Guller <alexg@mellanox.co.il>
Signed-off-by: Sharon Cohen <sharonc@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.
CC: Roland Dreier <roland@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Amir Vadai