This patch adds an essential check related to the size of the
payload to be transferred via aux channel.
Without this check dal_ddc_service_read_dpcd_data() is fed with
inappropriate payload size leading to deadlocks.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We have unused variables being populated when notifying pplib.
This change amends that.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
root cause:
DMCU try to perform a smoothness brightness change.Incorrect initial
brightness level causes the 1 sec dim.
Change:
Cache brightness level in stream, and clear it when edp backlight on.
If brightness level in stream is 0, set brightness with ramp value is 0.
DMCU will set the brightness without smoothness transition.
v2: squash in null pointer fix (Harry)
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is preparation for sharing client ID definitions
between amdgpu and amdkfd
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bw spreadsheet was updated while dce_calcs was not
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Increase clock, if current dpp div is 0 and request dpp div is 1, request clk is
higher than maximum dpp clk as per dpm table.
set dispclk to the value of maximum supported dpp clk
set div to 1
set dispclk to request value.
Decrease clock, currrent dpp div is 1 and request dpp div is 0, current clk is
higher than maximum dpp clk as per dpm table.
set dispclk to the value of maximum supported dpp clk
set div to 0
set dispclk to request value.
v2: squash in !DCN build fix
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The order of planes is given by the order they are enumerated
by kms.
Planes with a higher ID appears above planes with a lower ID.
Currently the planes are enumerated in the wrong order,
putting the nv12 only plane after the two RGBA planes.
This patch corrects the plane enumeration order such that all
the overlay planes are initialized first then the primary planes.
Due to this change in order the dc_add_plane_to_context() shall
receive the planes in reverse order hence this patch reverses
the parsing of planes in DM side itself.
v2: drop local reverse macro for upstream
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Time stamping will be part of surface, and will be updated when address is flipped.
FreeSync parameters will be attached to stream, as it adjusts the timing dynamically.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stats will be used for debug purposes
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The work around for hw bug causes S3 resume failure. Don't execute
disable vga logic if not in vga mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initializing ABM and DMCU modules for dce 80/81/83/100 as in DCE110
Adding constructors and destructors for each module.
Adding register list for DMCU in dce80 as some registers are missing
in dce80 from the basic list. DMCU is never used, so it would not have
any functional impact.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In MPO scenario when playing SDR clip in HDR desktop mode, Win is
boosting desktop and requests driver to boost MPO. But driver boosting
is currently done in regamma which is stream property and thus shared
between grph and video.
Redesigning the boosting in RV: use CM_HDR_MULT register which was added
for this scenario. It also has the benefit that it can be done in HIRQL.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use DC_LOGGER macro for logs.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These MACROS are only being used by a few files but
gets pulled in by dc.h
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change make sure bandwidth is set properly.
For increase bandwidth, set bandwidth before backend
and front end programming.
For decrease bandwidth, set bandwidth after.
To avoid smu hang when reboot and dpms due to 0 disp clk,
keep min disp clock as 100Mhz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Per discussion with VBIOS team, the orginal check is not correct in
all cases on latest VBIOS. Additional check is needed. This change should
maintain old behaviour on older VBIOS.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HW Engineer's Notes:
During switch from vga->extended, if we set the VGA_TEST_ENABLE and then
hit the VGA_TEST_RENDER_START, then the DCHUBP timing gets updated correctly.
Then vBIOS will have it poll for the VGA_TEST_RENDER_DONE and unset
VGA_TEST_ENABLE, to leave it in the same state as before.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
300Mhz disp clk limit was a workaround that was fixed in SMU and is no
longer needed.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM's documentation for the color transform matrix does not specify
whether the values are in signed-magnitude, or 2's complement.
Therefore, it was assumed to use 2's complement.
However, existing usermode implementations use signed-magnitude.
Therefore, conform to existing standards, and convert to 2's complement
internally.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix bug and make changes from review 132656
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoid hanging DMCU by setting abm level only when OTG unblanked
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Should return -ENOMEM when allocation fails.
Also, just return the error code instead of using a variable.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While checking plane states for updates during atomic check, we create
dc_plane_states in preparation. These dc states should be freed if
something errors.
Although the input transfer function is also freed by
dc_plane_state_release(), we should free it (on error) under the same
scope as where it is created.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
More stuff for 4.17. Highlights:
- More fixes for "wattman" like functionality (fine grained clk/voltage control)
- Add more power profile infrastucture (context based dpm)
- SR-IOV fixes
- Add iomem debugging interface for use with umr
- Powerplay and cgs cleanups
- DC fixes and cleanups
- ttm improvements
- Misc cleanups all over
* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux: (143 commits)
drm/amdgpu:Always save uvd vcpu_bo in VM Mode
drm/amdgpu:Correct max uvd handles
drm/amdgpu: replace iova debugfs file with iomem (v3)
drm/amd/display: validate plane format on primary plane
drm/amdgpu: Clean sdma wptr register when only enable wptr polling
drm/amd/amdgpu: re-add missing GC 9.1 and SDMA0 4.1 sh_mask header files
drm/amdgpu: give warning before sleep in kiq_r/wreg
drm/amdgpu: further mitigate workaround for i915
drm/amdgpu: drop gtt->adev
drm/amdgpu: add amdgpu_evict_gtt debugfs entry
drm/amd/pp: Add #ifdef checks for CONFIG_ACPI
drm/amd/pp: fix "Delete the wrapper layer of smu_allocate/free_memory"
drm/amd/pp: Drop wrapper functions for upper/lower_32_bits
drm/amdgpu: Delete cgs wrapper functions for gpu memory manager
drm/amd/pp: Delete the wrapper layer of smu_allocate/free_memory
drm/amd/pp: Remove cgs wrapper function for temperature update
Revert "drm/amd/pp: Add a pp feature mask bit for AutoWattman feature"
drm/amd/pp: Add auto power profilng switch based on workloads (v2)
drm/amd/pp: Revert gfx/compute profile switch sysfs
drm/amd/pp: Fix sclk in highest two levels when compute on smu7
...
In dce110, the plane configuration is such that plane 0
or the primary plane should be rendered with only RGB data.
This patch adds the validation to ensure that no video data
is rendered on plane 0.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The work around for hw bug causes S3 resume failure. Don't execute
disable vga logic if not in vga mode.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HW Engineer's Notes:
During switch from vga->extended, if we set the VGA_TEST_ENABLE and then
hit the VGA_TEST_RENDER_START, then the DCHUBP timing gets updated correctly.
Then vBIOS will have it poll for the VGA_TEST_RENDER_DONE and unset
VGA_TEST_ENABLE, to leave it in the same state as before.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
While checking plane states for updates during atomic check, we create
dc_plane_states in preparation. These dc states should be freed if
something errors.
Although the input transfer function is also freed by
dc_plane_state_release(), we should free it (on error) under the same
scope as where it is created.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before dig fe is enabled, infoframe can't be programmed. So in
suspend resume case our infoframe programmming was not going through.
This change changes the sequence so that infoframe is programmed
after.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixing null-deref on Vega10 due to regression after
'fix cursor related Pstate hang' change.
Added null checks in setting cursor position.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move cursor programming to inside the OTG_MASTER_UPDATE_LOCK
If graphics plane go from 1 pipe to hsplit, the cursor updates
after mpc programming and unlock. Which means there is a window
of time where cursor is enabled on the wrong pipe if it's on
the right side of the screen (i.e. case where cursor need to
move from pipe 0 to pipe 3 post split). This will cause pstate hang.
Solution is to program the cursor while still locked.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Because AMDGPU_CRTC_IRQ_VLINE1 = 6, it expected 6 more crtcs to be
programed with disabled irq state in amdgpu_irq_disable_all. That caused errors and accessed
the wrong memory location.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no need to call drm_mode_set_crtcinfo() again once
crtc timing is decided. Otherwise non-native/unsupported timing
might get overwritten.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There's no good place in DC to cover all place where stream signal should
be updated. update_stream_signal depends on timing which comes from DM.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We've got a helper function to call dc_create_stream_for_sink and one
other place that calls it directly. Make sure we call the helper
functions always since we need to update a bunch of things in stream and
don't want to miss that.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our APUs (Carrizo, Stoney, Raven) don't support it.
v2: Don't use is_apu as other ASICs might also not support it
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This makes the check for HDMI and dual-link DVI a bit more
straightforward.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With FBC enabled there was a potential null-deref
on topology change due to hardcorded pipe index.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When topology changed and rehook up MST display to the same DP
connector, need to take care of drm_dp_mst_port object.
Due to the topology is changed, drm_dp_mst_port and corresponding
i2c_algorithm object could be NULL in such situation.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The below commit
"drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2"
introduces a slight behavioral change to rmfb. Instead of disabling a crtc
when the primary plane is disabled, it now preserves it.
This change leads to BUG hit while performing atomic commit on amd driver.
As a fix this patch ensures that we disable the CRTC's with NULL FB by returning
-EINVAL and hence triggering fall back to the old behavior and turning off the
crtc in atomic_remove_fb().
V2: Added error check for plane_state and removed sanity check for crtc.
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There have been many reports of Ellesmere and Baffin systems not being
able to drive HDMI 4k60 due to the fact that we check the HDMI_6GB_EN
bit from VBIOS table. Windows seems to not have this issue.
On some systems we fail to the encoder cap info from VBIOS. In that case
we should default to enabling HDMI6G support.
This was tested by dwagner on
https://bugs.freedesktop.org/show_bug.cgi?id=102820
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch updates the dc's plane state with the parameters set by the
user side.
This is needed to validate the plane capabilities with the parameters
user space wants to set.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CZ & ST support uptil a limit 2:1 downscaling, this patch
adds validate_plane hook, that shall be used to validate
the plane attributes sent by the user space based
on dce110 capabilities.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_dm_atomic_check() is used to validate the entire configuration of
planes and crtc's that the user space wants to commit.
However amdgpu_dm_atomic_check() depends upon DRM_MODE_ATOMIC_ALLOW_MODESET
flag else its mostly dummy.
Its not mandatory for the user space to set DRM_MODE_ATOMIC_ALLOW_MODESET,
and in general its not set either along with DRM_MODE_ATOMIC_TEST_ONLY.
Considering its importantance, this patch defers the allow_modeset check
in dm_update_planes_state(), so that there shall be scope to validate
the configuration sent from user space, without impacting the population
of dc/dm related data structures.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In dce110, the plane configuration is such that plane 0
or the primary plane should be rendered with only RGB data.
This patch adds the validation to ensure that no video data
is rendered on plane 0.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean fake sink flag after detecting link on downstream port.
Fixing display light-up after "hot-unplug&plug again" downstream
of an active dongle.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
avoid build error:
drivers/gpu/drm/amd/amdgpu/../powerplay/inc/smu9_driver_if.h:342:3: error: redeclaration of enumerator ‘WM_COUNT’
WM_COUNT,
^
In file included from drivers/gpu/drm/amd/amdgpu/../display/dc/dm_services_types.h:32:0,
from drivers/gpu/drm/amd/amdgpu/../display/dc/dm_services.h:35,
from drivers/gpu/drm/amd/amdgpu/../display/modules/inc/mod_freesync.h:57,
from drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgpu_mode.h:48,
from drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgpu.h:55,
from drivers/gpu/drm/amd/amdgpu/../powerplay/inc/amd_powerplay.h:33,
from drivers/gpu/drm/amd/amdgpu/../powerplay/inc/smumgr.h:26,
from drivers/gpu/drm/amd/amdgpu/../powerplay/smumgr/vega10_smumgr.c:24:
drivers/gpu/drm/amd/amdgpu/../display/dc/dm_pp_smu.h:43:2: note: previous definition of ‘WM_COUNT’ was here
WM_COUNT,
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The below commit
"drm/atomic: Try to preserve the crtc enabled state in drm_atomic_remove_fb, v2"
introduces a slight behavioral change to rmfb. Instead of disabling a crtc
when the primary plane is disabled, it now preserves it.
This change leads to BUG hit while performing atomic commit on amd driver.
As a fix this patch ensures that we disable the CRTC's with NULL FB by returning
-EINVAL and hence triggering fall back to the old behavior and turning off the
crtc in atomic_remove_fb().
V2: Added error check for plane_state and removed sanity check for crtc.
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There have been many reports of Ellesmere and Baffin systems not being
able to drive HDMI 4k60 due to the fact that we check the HDMI_6GB_EN
bit from VBIOS table. Windows seems to not have this issue.
On some systems we fail to the encoder cap info from VBIOS. In that case
we should default to enabling HDMI6G support.
This was tested by dwagner on
https://bugs.freedesktop.org/show_bug.cgi?id=102820
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch updates the dc's plane state with the parameters set by the
user side.
This is needed to validate the plane capabilities with the parameters
user space wants to set.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CZ & ST support uptil a limit 2:1 downscaling, this patch
adds validate_plane hook, that shall be used to validate
the plane attributes sent by the user space based
on dce110 capabilities.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_dm_atomic_check() is used to validate the entire configuration of
planes and crtc's that the user space wants to commit.
However amdgpu_dm_atomic_check() depends upon DRM_MODE_ATOMIC_ALLOW_MODESET
flag else its mostly dummy.
Its not mandatory for the user space to set DRM_MODE_ATOMIC_ALLOW_MODESET,
and in general its not set either along with DRM_MODE_ATOMIC_TEST_ONLY.
Considering its importantance, this patch defers the allow_modeset check
in dm_update_planes_state(), so that there shall be scope to validate
the configuration sent from user space, without impacting the population
of dc/dm related data structures.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is really just a copy of dm_pp_clocks_state, so just use that one.
Thanks to Matthias Kaehlke for spotting this.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before dig fe is enabled, infoframe can't be programmed. So in
suspend resume case our infoframe programmming was not going through.
This change changes the sequence so that infoframe is programmed
after.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Applying min dispclk patch would result in incorrect dppclk divider
without this change
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Created a DC_LOGGER define. This is used to
pass the logger into the macros.
Anywhere we need to use the logger we need to define
DC_LOGGER
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Created MACROS for all log levels. Also Replaced
usage of dm_logger_write to the defined MACROS
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implementation of de-gamma, blnd-gamma, shaper and
3d lut's.
Removed memory allocations in transfer functions.
Refactor color module.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: Fix commit title
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the FBC buffer is allocated in VRAM, since VRAM usage is
dedicatedly for scanouts, by allocating FBC back buffer in GTT
shall help in conserving VRAM for other purposes.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mask and shift values for DCP0_REGAMMA_LUT_WRITE_EN_MASK were missing
from XFM_COMMON_MASK_SH_LIST_SOC_BASE. Add it.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
When CR fails to minimum link rate,
we should reduce lane count to the number lowest cr_done lanes.
[Code Review]
Jun Lei
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Brightness could not be changed for some panels whose DPCD_version is below 1.2
Now psr_version is added into stream, and it copies from the displayTarget's psr_version.
It checks if the stream's psr_versio is non-zero and sets the vsc info packet revision now.
Signed-off-by: Xingyue Tao <xingyue.tao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixed secondary screen only S4 resume, eDP is unintentionally
light up due to incorrect dpms off flag.
When entering S4, dpms off flags are set to true via
set power state. During resume, eDP is light up by vbios, so the flags
should be changed to false to match the real state.
By change the flag properly, eDP is able to be turned off properly as per
OS request.
This change may affect S3/S4 Shut down resume IOIC, need to verify
those cases.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Optimization in reset backend skips disable stream if it is
already done in dc_stream_set_dpms. However that path does
not disable az in order to prevent audio from toggling
between internal and external displays. This still need to
be done.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yue Hin Lau <Yuehin.Lau@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Points in the DRM LUT are spaced linearly. Points in hardware are spaced
exponentially, with greater density towards 0. To maintain low-end
accuracy in hardware when sampling the DRM LUT, more points are needed.
However, X doesn't seem to play with legacy LUTs of such size.
Therefore, check for legacy lut when updating DC states, and update
accordingly.
v2: Use a macro for the maximum drm LUT value.
v3: Update commit to reflect that this does not map 1-1 to HW
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add HPD delay timer support to
1. Single/dual link DVI.
2. DP to HDMI passive dongle
3. DP to DVI passive dongle.
Signed-off-by: John Barberiz <jbarberi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean fake sink flag after detecting link on downstream port.
Fixing display light-up after "hot-unplug&plug again" downstream
of an active dongle.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
some MST capable scaler doesn't like recieving CLEAR_PAYLOAD_ID_TABLE after
link training. move branch initialize to before link training
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver Changes:
- Lift alpha_support protection from Cannonlake (Rodrigo)
* Meaning the driver should mostly work for the hardware we had
at our disposal when testing
* Used to be preliminary_hw_support
- Add missing Cannonlake PCI device ID of 0x5A4C (Rodrigo)
- Cannonlake port register fix (Mahesh)
- Fix Dell Venue 8 Pro black screen after modeset (Hans)
- Fix for always returning zero out-fence from execbuf (Daniele)
- Fix HDMI audio when no no relevant video output is active (Jani)
- Fix memleak of VBT data on driver_unload (Hans)
- Fix for KASAN found locking issue (Maarten)
- RCU barrier consolidation to improve igt/gem_sync/idle (Chris)
- Optimizations to IRQ handlers (Chris)
- vblank tracking improvements (64-bit resolution, PM) (Dhinakaran)
- Pipe select bit corrections (Ville)
- Reduce runtime computed device_info fields (Chris)
- Tune down some WARN_ONs to GEM_BUG_ON now that CI has good coverage (Chris)
- A bunch of kerneldoc warning fixes (Chris)
* tag 'drm-intel-next-2018-02-21' of git://anongit.freedesktop.org/drm/drm-intel: (113 commits)
drm/i915: Update DRIVER_DATE to 20180221
drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced
drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning
drm/i915: Move the policy for placement of the GGTT vma into the caller
drm/i915: Also check view->type for a normal GGTT view
drm/i915: Drop WaDoubleCursorLP3Latency:ivb
drm/i915: Set the primary plane pipe select bits on gen4
drm/i915: Don't set cursor pipe select bits on g4x+
drm/i915: Assert that we don't overflow frontbuffer tracking bits
drm/i915: Track number of pending freed objects
drm/i915/: Initialise trans_min for skl_compute_transition_wm()
drm/i915: Clear the in-use marker on execbuf failure
drm/i915: Prune gen8_gt_irq_handler
drm/i915: Track GT interrupt handling using the master iir
drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use
drm: intel_dpio_phy: fix kernel-doc comments at nested struct
drm/i915: Release connector iterator on a digital port conflict.
drm/i915/execlists: Remove too early assert
drm/i915: Assert that we always complete a submission to guc/execlists
drm: move read_domains and write_domain into i915
...
Currently all cursor related functions are made to all
pipes that are attached to a particular stream.
This is not applicable to pipes that do not have cursor plane
initialised like underlay.
Hence this patch allows cursor related operations on a pipe
only if ipp in available on that particular pipe.
The check is added to set_cursor_position & set_cursor_attribute.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The drm layer expects aux->transfer() to return the payload bytes read.
Currently dm_dp_aux_transfer() returns the payload size which does not
gets updated during the read, hence not giving the right data for the
drm layer to pars edid. This leads to the drm layer to conclude as the
edid is BAD and hence some monitors/devices dont get detected properly.
This patch changes the return type of dm_dp_aux_transfer() to actual
bytes read during DP_AUX_NATIVE_READ & DP_AUX_I2C_READ.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently all cursor related functions are made to all
pipes that are attached to a particular stream.
This is not applicable to pipes that do not have cursor plane
initialised like underlay.
Hence this patch allows cursor related operations on a pipe
only if ipp in available on that particular pipe.
The check is added to set_cursor_position & set_cursor_attribute.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
- Powerplay fixes for cards with no displays attached
- Couple of DC fixes
- radeon workaround for PPC64
* 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: insist on 32-bit DMA for Cedar on PPC64/PPC64LE
drm/amd/display: VGA black screen from s3 when attached to hook
drm/amdgpu: Unify the dm resume calls into one
drm/amdgpu: Add a missing lock for drm_mm_takedown
Revert "drm/radeon/pm: autoswitch power state when in balanced mode"
drm/amd/powerplay/smu7: allow mclk switching with no displays
drm/amd/powerplay/vega10: allow mclk switching with no displays
This patch fix the following build warnings:
CC [M] drivers/gpu/drm/amd/amdgpu/amdgpu_drv.o
cc1: warning: ../display/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: ../display/include: No such file or directory [-Wmissing-include-dirs]
CC [M] drivers/gpu/drm/amd/amdgpu/amdgpu_device.o
cc1: warning: ../display/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: ../display/include: No such file or directory [-Wmissing-include-dirs]
[...]
This warning is shown for each file in amdgpu directory, so it spams a lot.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On lkml suggestions were made to split up such trivial typo fixes into per subsystem
patches:
--- a/arch/x86/boot/compressed/eboot.c
+++ b/arch/x86/boot/compressed/eboot.c
@@ -439,7 +439,7 @@ setup_uga32(void **uga_handle, unsigned long size, u32 *width, u32 *height)
struct efi_uga_draw_protocol *uga = NULL, *first_uga;
efi_guid_t uga_proto = EFI_UGA_PROTOCOL_GUID;
unsigned long nr_ugas;
- u32 *handles = (u32 *)uga_handle;;
+ u32 *handles = (u32 *)uga_handle;
efi_status_t status = EFI_INVALID_PARAMETER;
int i;
This patch is the result of the following script:
$ sed -i 's/;;$/;/g' $(git grep -E ';;$' | grep "\.[ch]:" | grep -vwE 'for|ia64' | cut -d: -f1 | sort | uniq)
... followed by manual review to make sure it's all good.
Splitting this up is just crazy talk, let's get over with this and just do it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[Description] For MST, DC already notify MST sink for MST mode, DC stll
check DP SINK DPCD register to see if MST enabled. DP RX firmware may
not handle this properly.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_dm_display_resume is now called from dm_resume to
unify DAL resume call into a single function call
There is no more need to separately call 2 resume functions
for DM.
Initially they were separated to resume display state after
cursor is pinned. But because there is no longer any corruption
with the cursor - the calls can be merged into one function hook.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously, the number of software segmets per region was reduced to 16.
This needs to be reflected in the sampling distance (increment) used when
translating to the hardware format.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some refactoring and optimizations in color module.
Added de gamma 2.2 & 2.4, also re gamma 2.2.
Added interface for diagnostic for de gamma & de pq.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add basic logging for DPCD access. Does not print
by default.
Currently only prints first byte of the data accessed.
Technical debt: Need to make it so that the entire
data block accessed is printed. Also need to log
address space that's not DPCD.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Brightness couldn't change when booting up in DC mode.
It was because "psr_enabled" flag was not set to true before
setting vsc packet revision, causing packet rev setup was skipped.
Now instead of checking the psr flag, it checks if the DPCD_REV >= 1.2
and set the vsc packet revision.
Signed-off-by: Tao <xtao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We have an mst dock firmware that will emulate an EDID with bad
checksum.
v2: Tread -> Treat
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Identical to the two entries above them.
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously, FBC dynamic allocation relied on connector modes
populated during dm init. This is only the case if
DRM_FBDEV_EMULATION config flag is enabled.
Moving fbc allocation from dm_late_init() to
amdgpu_dm_connector_get_modes() where actual modes init happens.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Shirish Shankarappa <Shirish.S@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HDMI HPD's generic solution makes the monitor
patch code unnecessary so anything related has
been removed.
Signed-off-by: John Barberiz <jbarberi@amd.com>
Reviewed-by: John Barberiz <jbarberi@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Skipping the first frame will prevent uncoooked values most of the time.
However, in some unlikely cases, the second frame will be uncooked as
well.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement CRC for DCE8. Registers remain the same, so call DCE110 code
directly.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clear up the logic, and enable programming truncation as a bit reduction
mode.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When user-mode is using 8bpc, the hardware represents it internally
using a higher bit depth. This causes problems when comparing CRCs for
color managment tests.
We need to disable dithering as well, since it makes CRC values
non-deterministic.
It's easy to see why dithering needs to be disabled, The reason why
truncation also needs to be enabled is better described with an example.
Consider the folowing which tests the color transform matrix (CTM):
Expected CRC = FB_A -> Degamma (Bypassed) -> CTM (Bypassed)
|
v
Obtain CRC <- Regamma(Bypassed)
Actual CRC = FB_B -> Degamma (Bypassed) -> CTM (0.5*Identity)
|
v
Obtain CRC <- Regamma(Bypassed)
FB_A contains a solid red color at half intensity (127 @ 8bpc)
FB_B contains a solid red color at full intensity (255 @ 8bpc)
We expect that Expected CRC = Actual CRC, but that's not the case. When
the CTM is applied, the output is at half intensity, but also at a
higher bit depth within hardware. i.e. 255/2 = 127.5: not representable
in 8bpc, but can be at 10bpc. This causes the two CRC's to be different.
The solution is to truncate the output bit depth to the same as input
when enabling CRC capture. Since Linux only supports 8bpc, hard code
that for now.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We will need this to disable dither for CRC capture.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hookup new color management functions into amdgpu_dm:
- Notify DRM that we support CRTC color management during CRTC init
- Call color management functions within atomic check to update dc
states in preparation for a commit
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement color management functionalities within amdgpu_dm_color, and
expose functions within amdgpu_dm.h.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also guard includes that we don't need.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The MAX_LOW_POINT macro should reflect the maximum low point within
hardware. Otherwise, sampling for the hardware points from the output
transfer function (OTF) will be incorrect.
Also, fix usage of MAX_LOW_POINT accordingly.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Both functions are the same
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This path fixed specific eDP panel cold boot black screen
due to unnecessary enable link.
Change:
In case of boot up with eDP, if OS is going to set mode
on eDP, keep eDP light up, do not disable and reset corresponding
HW.
This change may affect dce asics and S3/S4 Resume with multi-monitor.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These should only be non-0 if big hammer w/a is implemented. Currently
DC doesn't implement it, so leave them 0.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description] For MST, DC already notify MST sink for MST mode, DC stll
check DP SINK DPCD register to see if MST enabled. DP RX firmware may
not handle this properly.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Disabled HPD filter and used HPD software timer instead
- Allows DM to disable HPD filtering
Signed-off-by: John Barberiz <jbarberi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_dm_display_resume is now called from dm_resume to
unify DAL resume call into a single function call
There is no more need to separately call 2 resume functions
for DM.
Initially they were separated to resume display state after
cursor is pinned. But because there is no longer any corruption
with the cursor - the calls can be merged into one function hook.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Missed that with a previous change that removed unused files.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
calcs uses the compiler option -mpreferred-stack-boundary=4 to configure
a stack alignment of 16 bytes. Clang uses the option -mstack-alignment
instead, which expects as parameter the alignment in bytes, and not a
power of two like -mpreferred-stack-boundary.
Probe for both compiler options and use the correct one, similar to
what is done in arch/x86/Makefile.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DML uses the compiler option -mpreferred-stack-boundary=4 to configure
a stack alignment of 16 bytes. Clang uses the option -mstack-alignment
instead, which expects as parameter the alignment in bytes, and not a
power of two like -mpreferred-stack-boundary.
Probe for both compiler options and use the correct one, similar to
what is done in arch/x86/Makefile.
Reported-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use a variable for common CFLAGS instead of specifying the same flags
for every source file.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use a variable for common CFLAGS instead of specifying the same flags
for every source file.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver passes GRAPHICS_CSC_ADJUST_TYPE_SW of type enum
graphics_csc_adjust_type to program_color_matrix(), however the function
expects a parameter of type enum grph_color_adjust_option. Supposedly
the intention was to pass GRPH_COLOR_MATRIX_SW, which has the same value
as GRAPHICS_CSC_ADJUST_TYPE_SW, so the mismatch didn't cause any trouble.
Pass GRPH_COLOR_MATRIX_SW to program_color_matrix() instead of
GRAPHICS_CSC_ADJUST_TYPE_SW, this also fixes the following warning when
building the kernel with clang:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:1129:24:
error: implicit conversion from enumeration type
'enum graphics_csc_adjust_type' to different enumeration type
'enum grph_color_adjust_option' [-Werror,-Wenum-conversion]
xfm_dce, tbl_entry, GRAPHICS_CSC_ADJUST_TYPE_SW);
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The double parentheses are not needed. Removing them fixes multiple
warnings like this when building with clang:
drivers/gpu/drm/amd/amdgpu/../display/dc/calcs/dce_calcs.c:617:42:
error: equality comparison with extraneous parentheses
[-Werror,-Wparentheses-equality]
if ((data->graphics_micro_tile_mode == bw_def_rotated_micro_tiling)) {
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are several optimizations:
1) Use predefined SRGB, don't calculate. This is the most common case.
2) Precompute HW X points at boot since they're fixed in ColModule
3) Precompute PQ - it never changes and is very CPU intensive in fixed pt.
4) Reduce number of points in ColModule to 512 (32x16) from 1024. This also
requires reducing some regions for legacy DCEs to 16 pts at most.
Performance
1) is super-fast, build_output_tf is 1-2us, down from 25000-30000.
Programming also fast since only one reg write.
2)+3) gives build_output_tf for PQ in ~100us range, down from ~80000-110000
2) + 4) results in slightly over 50% improvement. It gives an idea of the
savings when we can't use SRGB or PQ table (e.g. sdr white level > 80).
There's also a bit of refactoring: renaming some stuff that was misleading
and removing a lot of magic numbers that novices might not be able to
understand where they come from and what they mean.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: John Barberiz <jbarberi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
System soft hang when hotplug specific 4K DP panel
due to link caps read error and incorrect link setting
parmas to enable dp.
Add status check for DPCD read and add return value
for detect dp, in case of false, return from caller,
avoid further false operation.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixing null-deref on Vega10 due to regression after
'fix cursor related Pstate hang' change.
Added null checks in setting cursor position.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As a precaution to prevent cases where cursor is enabled on a pipe
that is disabled, always turn off cursor when disconnecting plane.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Previous code did some calculations with a mix of normal integers and
integers aligned as U2.24 fixed-point values.
* There were bugs in the conversion of the final result into the
S4.19 values required for the registers.
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move cursor programming to inside the OTG_MASTER_UPDATE_LOCK
If graphics plane go from 1 pipe to hsplit, the cursor updates
after mpc programming and unlock. Which means there is a window
of time where cursor is enabled on the wrong pipe if it's on
the right side of the screen (i.e. case where cursor need to
move from pipe 0 to pipe 3 post split). This will cause pstate hang.
Solution is to program the cursor while still locked.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Because AMDGPU_CRTC_IRQ_VLINE1 = 6, it expected 6 more crtcs to be
programed with disabled irq state in amdgpu_irq_disable_all. That caused errors and accessed
the wrong memory location.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When disable plane, check power gate flag in hubp with pipe_ctx,
not with res_pool.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If non-standard gamma type detected set identity matrix flag
so that we can bypass the gamma mode.
Signed-off-by: John Barberiz <jbarberi@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If CONFIG_DEBUG_FS is disabled, then CRC should also be disabled.
Therefore, amdgpu_dm_crtc_handle_crc_irq was redefined as a no-op
function within amdgpu_dm.h.
However, since amdgpu_dm.h is included in multiple files, this caused
conflicts when linking during compile. Therefore, Use a macro to
define the function as a no-op instead.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no need to call drm_mode_set_crtcinfo() again once
crtc timing is decided. Otherwise non-native/unsupported timing
might get overwritten.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No longer used since we changed the MC programming sequence.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Building the amd display driver with link-time optimizations revealed a bug
that caused dal_cmd_tbl_helper_dce80_get_table() and
dal_cmd_tbl_helper_dce110_get_table() get called with an incompatible
return type between the two callers in command_table_helper.c and
command_table_helper2.c:
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/dce80/command_table_helper_dce80.h:31: error: type of 'dal_cmd_tbl_helper_dce80_get_table' does not match original declaration [-Werror=lto-type-mismatch]
const struct command_table_helper *dal_cmd_tbl_helper_dce80_get_table(void);
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/dce80/command_table_helper_dce80.c:351: note: 'dal_cmd_tbl_helper_dce80_get_table' was previously declared here
const struct command_table_helper *dal_cmd_tbl_helper_dce80_get_table(void)
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/dce110/command_table_helper_dce110.h:32: error: type of 'dal_cmd_tbl_helper_dce110_get_table' does not match original declaration [-Werror=lto-type-mismatch]
const struct command_table_helper *dal_cmd_tbl_helper_dce110_get_table(void);
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/dce110/command_table_helper_dce110.c:361: note: 'dal_cmd_tbl_helper_dce110_get_table' was previously declared here
const struct command_table_helper *dal_cmd_tbl_helper_dce110_get_table(void)
The two versions of the structure are obviously derived from the same
one, but have diverged over time, before they got added to the kernel.
This moves the structure to a new shared header file and uses the superset
of the members, to ensure the interfaces are all compatible.
Fixes: ae79c310b1 ("drm/amd/display: Add DCE12 bios parser support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The trailing semicolon is an empty statement that does no operation.
Removing the two instances of them since they don't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The atomic debugfs stuff gets created in drm_dev_alloc()
but this gets called before we've enumerated all of our
IPs, so move the DRIVER_ATOMIC flag setting to fix that.
Since DRIVER_ATOMIC is a driver flag it's currently global
to the driver so setting it affects all GPUs driven by the
driver. Unfortunately, not all GPUs support atomic. Warn
the user if that is the case.
This is the same as our current behavior, but at least the
atomic debugfs stuff gets created now.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They seem to be obsolete.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Sequencing bug of not resetting delay on disconnect to default values
Signed-off-by: John Barberiz <jbarberi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove aux engine register programming,when freeing the engine
as it was a temporary workaround.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: John Barberiz <jbarberi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Geling Li <geling.li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Directly editing pipe config outside of formula is error prone
and results in higher clocks being used when splitting.
For this reason we reverted to using bounding box hacking
to split. Since sometimes this erroneusly results in higher dpm
being required we unhack the bounding box and recalculate to allow
dpm0 is possible.
Side effect is we will lose some stutter efficiency
in non dpm0 cases. This is not a big concern since increased stutter
efficiency saves an order of magnitude less power than lower dpm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use tg count in resource pool for further reference.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lock top_pipe when doing update plane addr for split pipe freesync case
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There's no good place in DC to cover all place where stream signal should
be updated. update_stream_signal depends on timing which comes from DM.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If crc is disabled, early return when getting crc's. That way, we avoid
reading extra registers within the pflip high irq.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We're currently not using this.
v2: More files and includes to remove.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add display to the name for consistency.
Signed-off-by: Samuel Li <Samuel.Li@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add display to the name for consistency.
Signed-off-by: Samuel Li <Samuel.Li@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add display to the name for consistency.
Signed-off-by: Samuel Li <Samuel.Li@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add display to the name for consistency.
Signed-off-by: Samuel Li <Samuel.Li@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And rename it to amdgpu_gmc as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Samuel Li <Samuel.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VM support is only available for CZ and newer APUs. Trying to
enable it for dGPU will blow up in DC.
v2: Don't enable gpu_vm_support for Raven yet since it leads to
a black screen. Need to debug this further before enabling.
Change-Id: Ibe467c36affe2e7a7ee740c8d4f73027ca807178
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
CC: Christian Koenig <christian.koenig@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On CZ and newer APUs we can pin the fb into GART as well as VRAM.
v2: Don't enable gpu_vm_support for Raven yet since it leads to
a black screen. Need to debug this further before enabling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We assume FP16 1.0 frame buffer value maps to 80 nits.
DC changes are to make this configurable.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dcn10_init_hw such that initialization of relevant
HW blocks for Maximus FPGA are also initialized (and not skipped).
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement the timing generator hooks for configure_crc and get_crc.
Also implement is_tg_enabled, as configure_crc uses it.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add interfaces in DC for per CRTC CRC configuration and fetching.
Also implement amdgpu_dm functions to hook onto DRM.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cleanup to remove unused register definition from hw sequencer
header file since implementation moved from hw sequencer to dchubub file.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to use loop find opp, use opp in stream_res.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixing regression introduced by
'Use real BE and FE index to program regs.'
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's unused since the drm_edid_to_eld cleanup
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We no longer change the plane state pointer for full updates, and as
such, we weren't setting the input transfer function and programming the
degamma registers when we are supposed to. Check for a full update, an
input TF change, or a gamma change in the update flags instead to correct
this.
Signed-off-by: Andrew Jiang <Andrew.Jiang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will allow us to clean up resources on a stream as needed.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We've got a helper function to call dc_create_stream_for_sink and one
other place that calls it directly. Make sure we call the helper
functions always since we need to update a bunch of things in stream and
don't want to miss that.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It would be useful to know which clocks are unsupported when logging an
error message about unsupported clocks.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In case of some pipes are fused, pipe_idx should not
be used to program pipe regs. Instead of that, BE and FE
inst number should be used for reg index.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our APUs (Carrizo, Stoney, Raven) don't support it.
v2: Don't use is_apu as other ASICs might also not support it
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It might be good to understand why validate fails.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Proper sequence should be:
disable backlight
dp blank
disable output
edp power off
In enable accelatate mode, all the encoder and controller
are disabled, so move disable eDP to the function is the
easiest way to implement.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This makes the check for HDMI and dual-link DVI a bit more
straightforward.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Verify that the stream is master - and program only the slave displays
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With FBC enabled there was a potential null-deref
on topology change due to hardcorded pipe index.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When topology changed and rehook up MST display to the same DP
connector, need to take care of drm_dp_mst_port object.
Due to the topology is changed, drm_dp_mst_port and corresponding
i2c_algorithm object could be NULL in such situation.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After reworking FBC init for dynamic mem alloc
old FBC init code in DC became redundant.
Removing it.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- FBC init reworked to alloc memory based on display mode.
- Removed asic-dependencies from dm
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows Maximus emulation to more closely mirror actual silicon
execution.
* Enable pool->base.display_clock creation on Maximus.
* Enable rest of dce110_apply_ctx_to_hw on Maximus.
* Remove apply_ctx_to_hw_fpga (no longer necessary with the full
dce110_apply_ctx_to_hw enabled).
* Disable the dmcu->funcs->set_psr_wait_loop call in dce112_set_clock
for Maximus (this was the only fix-up necessary after enabling
dce110_apply_ctx_to_hw; everything else works unmodified on
Maximus).
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Maximus testing now defaults to a 700 MHz emulated dispclk
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
570e86963a ("drm: Widen vblank count to 64-bits [v3]") changed the
return type for drm_crtc_vblank_count() to u64. This could cause
potential problems if the return value is used in arithmetic operations
with a 32-bit reference HW vblank count. Explicitly typecasting this down
to u32 either fixes a potential problem or serves to add clarity in case
the typecasting was implicitly done.
Cc: Keith Packard <keithp@keithp.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com> for both this patch
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180203051302.9974-4-dhinakaran.pandiyan@intel.com
I assumed wrongfully that all relevant functions should be implemented.
Apparently this isn't the case. Demote the print to debug level for now.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yue Hin Lau <Yuehin.Lau@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Updates to FMT and OPPBUF programming from HW team
pseudocode review.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yue Hin Lau <Yuehin.Lau@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Shirish S