It is not necessary to reset the queue in the hns3_uninit_all_ring(),
since the queue is stopped in the down operation, and will be reset
in the up operation. And the judgment of the HCLGE_STATE_RST_HANDLING
flag in the hclge_reset_tqp() is not correct, because we need to reset
tqp during pf reset, otherwise it may cause queue not being reset to
working state problem.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_get_ring_config()/hns3_queue_to_ring()/
hns3_get_vector_ring_chain() failed during resetting, the allocated
memory has not been freed before these three functions return. So
this patch adds error handler in these functions to fix it.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_nic_init_vector_data() fails to map ring to vector,
it should cancel the netif_napi_add() that has been successfully
done and then exits.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the error recovery for the HNS hw errors.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set of hw errors occurred in the HNS3 are reported to the
hns3 driver through PCIe AER and RAS.The error info will be
processed and appropriately recovered.
This patch adds error_detected callback and error processing.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a big fragment using multiple buffer descriptor,
hns3 does one maping, but do multiple unmapping when tx is done,
which may cause unmapping problem.
To fix it, this patch makes sure the value of desc_cb.length of
the non-first bd is zero. If desc_cb.length is zero, we do not
unmap the buffer.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep symmetrical, this patch renames hns_nic_dma_unmap to
hns3_clear_desc.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unifies big tx fragment handling for tso and non-tso
case.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To solve the L3 checksum error problem which happens when driver
does not clear L3 checksum, DMA map should be done after calling
skb_cow_head.
This patch moves DMA map into hns3_fill_desc to ensure that DMA
map is done after calling skb_cow_head.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes hns3_fill_desc_tso in preparation for
fixing some desc filling bug, because for tso or non-tso
case, we will use the unified hns3_fill_desc.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resumes promisc mode and vlan filter status after reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver does nothing when mac vlan table is full.
In this case, the packet with new mac address will be dropped
by hardware. This patch adds check for the result of sync mac
address, and enable promisc mode when mac vlan table is full.
Furtherly, disable vlan filter when enable promisc by user
command.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In revision 0x20, we use vlan id != 0 to check whether a vlan tag
has been offloaded, so vlan id 0 is not supported.
In revision 0x21, rx buffer descriptor adds two bits to indicate
whether one or more vlan tags have been offloaded, so vlan id 0
is valid now.
This patch seperates the handle for vlan id 0, add vlan id 0 support
for revision 0x21.
Fixes: 5b5455a9ed ("net: hns3: Add STRP_TAGP field support for hardware revision 0x21")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For mta table support has been dropped, remove the code for mta table.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, the mac vlan table entries are not cleared when
unload hns3 driver. The dirty mac vlan table entries will make the
result of looking up mac vlan table being unexpected.
When doing core reset or global reset, the firmware will clear all
the tables for driver, and driver shouldn't send any commands to
firmware during reset. But when doing function reset, the driver
needs to clear the tables itself.
This patch clears the mac vlan table entries for each client when
unload driver or reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds switch for flow director with ethtool command
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all flow director rules when unload hns3 driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, remove all entries in TCAM block, and keep flow
director rules list. After finishing reset, restore all entries.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow director is a new feature supported by hardware with revision 0x21.
This patch adds flow direcor initialization for each PF. It queries flow
director mode and tcam resource from firmware, selects tuples used for
input key.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user's coal configuration will be lost after reset, so the tx_coal
and rx_coal fields are added to the struct hns_nic_priv to save the coal
configuration and used to restore the user's configuration after the reset
is complete.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current hns3_get_max_available_channels returns the total number
of queues for the device, which makes ethtool -L set the number of queues
per channel queues incorrectly, so hns3_get_max_available_channels should
return the maximum available number of queues per channel, depending on
the total number of queues allocated and the hardware configurations.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hns3_nic_change_mtu will try to down the netdev before
setting mtu, and it does not up the netdev when the setting fails,
which causes netdev not up problem.
This patch fixes it by not returning when the setting fails.
Fixes: a8e8b7ff35 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for sctp checksum offload.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are already multiple types packets statistics for error packets,
it's unnecessary to print them, which may affect the rx performance if
print too many.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dma_mapping_error is unlikely happened, this patch adds unlikely for
dma_mapping_error check.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When nic down, it firstly calls netif_tx_stop_all_queues(), then calls
napi_disable(). But napi_disable() will wait current napi_poll finish,
it may call netif_tx_wake_queue(). This patch fixes it by add nic state
checking.
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few "switch-case" codes missed handle for default case. For
some abnormal case, it should return error code instead of return 0.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the .ndo_do_ioctl net_device_ops operation to support
the PHY MII ioctl for PF driver.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The the actual Tx work is minimal, driver can clean up as more
Tx descriptors as possible in a irq.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds unlikely for buf_num check.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All irq will float to cpu0 if do not set irq affinity.
This patch adds default irq affinity in hns3 driver, users can
also change the irq affinity in OS.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements shutdown ops in hns3 pci driver, which
unloads the hns3 driver and set the power state to D3hot.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'truesize' is supposed to be u32, not int, so fix it.
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revision(0x20) HW does not support enabling or disabling individual
netdev's HW_VLAN_CTAG_FILTER feature, and Revision(0x21) supports
enabling or disabling individual netdev's HW_VLAN_CTAG_FILTER
feature.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS3_RING_TX_RING_TC_REG register is used to map tx ring to
specific tc, the tx queue to tc mapping is needed by the hardware
to do the correct tx schedule.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no HNS3_RING_TX_RING_BD_LEN_REG register according
to UM, so this patch removes it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114789 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msix number for vf is different, depends on the max vf number.
Futherly if the vf supports roce, the offset of msix is not fixed.
It's incorrect to fix the msix number to 33. This patch fixes it by
querying the msix number from firmware, and adjusting it with roce
support.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SPDX identifiers to HNS3 PF driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The input parameter "dev" of hns3_irq_handle() is indeed
used as a tqp vector, it is misleadin.
The struct member "flag" is used to indicate ring type,
so rename it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
handle->reset_level is assigned to HNAE3_NONE_RESET when client is
initialized, if a tx timeout happens right after initialization,
then handle->reset_level is not resetted to HNAE3_FUNC_RESET in
hclge_reset_event, which will cause reset event not properly
handled problem.
This patch fixes it by setting handle->reset_level properly when
client is initialized.
Fixes: 6d4c3981a8 ("net: hns3: Changes to make enet watchdog timeout func common for PF/VF")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration of the ring will be used to reinitialize the
ring after the hardware reset is completed. So we should not
release and reacquire this configuration during reset.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, netdev has not been brought up is not an error,
it means that we do not need do the stop operation, so just return
zero.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware only support tcp/udp/sctp l4 checksum offload, but
the driver currently tell hardware to do l4 checksum offlad when
l3 is IPv4 or IPv6, which may cause checksumm error.
This patch fixes it by only enabling the l4 offload when l4 is
tcp/udp/sctp.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tc related configuration is not setup when the
netdev is first up, which cause the stack only using tc 0
problem.
This patch fixes it by setting the tc related configuration
using the info from NCL_CONFIG when netdev is first up.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'protocol' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'protocol' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, prefix hnae_ should be modified to hnae3_.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reference to Documentation/DMA-API-HOWTO.txt,
Streaming DMA mappings which are usually mapped for one DMA transfer,
Network card DMA ring descriptors should use Consistent DMA mappings.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface h->ae_algo->ops->put_vector is called in both
hns3_nic_dealloc_vector_data and hns3_nic_uninit_vector_data in
hns3_client_uninit, this will cause vector freed twice.
This patch remove the Redundant put_vector to make vector freed
only once.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first bd of a packet is invalid and invalid ring head for tx
IRQ is not offen, they may occur when there is error,
Add unlikely for error check branch is better for performance.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW supports UDP, TCP and SCTP packets checksum for both ipv4 and
ipv6, but do not support other type packets checksum for ipv4 or
ipv6.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current process, the multicast MAC is added to both MAC_VLAN
table and MTA table, this will reduce the utilization of the resource.
This patch improves the process of adding multicast MAC address, the
new process starts using the MTA table to add multicast MAC after the
MAC_VLAN table is full, and the MTA is disable if it is no longer used.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Reviewed-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when skb->encapsulation is 0, skb->ip_summed is CHECKSUM_PARTIAL
and it is udp packet, which has a dest port as the IANA assigned.
the hardware is expected to do the checksum offload, but the
hardware will not do the checksum offload when udp dest port is
4789.
This patch fixes it by doing the checksum in software.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing function reset or insmod hns3 dirver after rmmod,
the entries of mac vlan table are not cleared, which may cause
init mac address failed. This patch fixes it by clearing the
old mac address when doing function reset or rmmod hns3 driver.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checking for new mac address. It doesn't need to config
the mac vlan table if it's already in use.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for IFF_ALLMULTI flag to HNS3 PF and VF
driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we down the port, some packets are left in TX/RX buffer. When we
up the port again, these old packets are forwarded to protocol stack
or are sent to internet. It will make some problem. TX/RX buffer should
be cleared when stopping port. This patch adds some function to ensure
the buffer is clean when port is started. We should clear the rings
when clients are being un-initialized as well.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our code will ensure that hns3_clear_tx_ring is not used to cleared
RX rings and hns3_clear_rx_ring is not used to cleared TX rings. So
the ring type check is unnecessary.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware Revision(0x21) Buffer Descriptor adds a field STRP_TAGP
for vlan stripped processed indication. STRP_TAGP field has 2 bits,
bit 0 is stripped indication of the vlan tag in outer vlan tag
field, bit 1 is stripped indication of the vlan tag in inner vlan
tag field. For each bit, 0 indicates the tag is not stripped and
1 indicates the tag is stripped.
This patch adds STRP_TAGP support for revision(0x21), and does not
change the revision(0x20) action.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the latest revision of the hardware, if a packet is spanning
across multiple BDs then only VLD bit and current data size info
is valid in each BD, and rest of the information is only valid
in the last BD of the packet. In such case we should make sure
we are fetching RX packet size from the first descriptor and
information like VLAN should be fetched from last BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hns3 driver has been built into kernel and then loaded with
the same driver which built as KLM, it may trigger an error like
below:
[ 20.009555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 20.016789] hns3: Copyright (c) 2017 Huawei Corporation.
[ 20.022100] Error: Driver 'hns3' is already registered, aborting...
[ 23.517397] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 23.691583] Process insmod (pid: 1982, stack limit = 0x00000000cd5f21cb)
[ 23.698270] Call trace:
[ 23.700705] __list_del_entry_valid+0x2c/0xd8
[ 23.705049] hnae3_unregister_client+0x68/0xa8
[ 23.709487] hns3_init_module+0x98/0x1000 [hns3]
[ 23.714093] do_one_initcall+0x5c/0x170
[ 23.717918] do_init_module+0x64/0x1f4
[ 23.721654] load_module+0x1d14/0x24b0
[ 23.725390] SyS_init_module+0x158/0x208
[ 23.729300] el0_svc_naked+0x30/0x34
This patch fixes it by adding module version info.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the missing initialization of the client list node
in the hnae3_register_client() function.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the RX leg driver needs to fetch the ethernet header
length from the RX'ed Buffer Descriptor. Currently, proprietary
version hns3_nic_get_headlen is being used to fetch the header
length which uses l234info present in the Buffer Descriptor
which might not be valid for the first Buffer Descriptor if the
packet is spanning across multiple descriptors.
Kernel default eth_get_headlen API does the job correctly.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the error reported by Intel's kbuild and fixes a
return value in one of the legs, caught during review of the original
patch sent by kbuild.
Fixes: fdb793670a00 ("net: hns3: Add support of .sriov_configure in HNS3 driver")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As HNS3 driver will enable SRIOV default and enable all VFs the
HW support, if PF and VF driver compiled to kernel, VF driver
will work on host default, it is not right.
This patch adds support for hns3_driver.sriov_configure to support
user configs the VF_num, and do not enable sriov default.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Suggested-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hclge.ko has not been inserted, the value of ret always is zero
in hnae3_register_ae_dev. If hclge.ko has been inserted, the value
of ret is zero or non zero. Different execution ways have different
results. It is confusing.
The ae_dev which is initialized failed can be reinitialized when we
remove hclge.ko and insert it again. For the case initializing client
instance, it is just like the case initializing ae_dev. The main function
of hnae3_register_ae_dev is adding the ae_dev to ad_dev list. Because
adding ae_dev is always ok, we does not need to return any in this
function.
This patch changes the return type of hnae3_register_ae_dev from int
to void.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hnae3_unregister_ae_algo is called by PF, pci_disable_sriov is
called. And then, hns3_remove is called by VF. We get deadlocked in
this case.
Since VF pci device is dependent on PF pci device, When PF pci device
is removed, VF pci device must be removed. Also, To solve the deadlock
problem, VF pci device should be removed before PF pci device is removed.
This patch moves pci_enable/disable_sriov from hclge to hns3 to solve
the deadlock problem.
Also, we do not need to return EPROBE_DEFER in hnae3_register_ae_dev,
because SRIOV is no longer enabled in the context calling
hnae3_register_ae_dev. Mutex_trylock can be replaced with mutex_lock.
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The head or tail in hardware is not longer valid when resetting,
current hns3_clear_all_ring use them to clean the ring, which
will cause problem during resetting.
This patch fixes it by using next_to_use and next_to_clean in
the ring struct.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The add/del_tunnel_udp is not implemented in hclge_main moulde,
the NETIF_F_RX_UDP_TUNNEL_PORT feature bit is added automatically
by stack when ndo_udp_tunnel_add is not null in dev->netdev_ops.
This patch removes the add/del_tunnel_udp related function, for
we do not support this feature now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_init_mac_addr is called during reset process, it will
get the mac address from NCL_CONFIG and set it to hardware. If
user has changed the mac address, then the mac address set by
user is lost during resetting.
This patch fixes it by not getting the mac address from NCL_CONFIG
when resetting.
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of hardware rx-vlan-offload to VF driver.
VF uses mailbox to convey PF to configure the hardware.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the function being used to fetch L4
protocol outer header. Mistakenly skb_inner_transport_header
API was being used earlier.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for explicit calls of devm_kfree(), as the allocated
memory will be freed during driver's detach.
The driver core clears the driver data to NULL after device_release.
Thus, it is not needed to manually clear the device driver data to NULL.
So remove the unnecessary pci_set_drvdata() and devm_kfree().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Third parameter of hnae_set_field is shift, But a mask is given. This
patch fixes it by replacing HNS3_TXD_BDTYPE_M with HNS3_TXD_BDTYPE_S.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 drivers enet layer, used for the ring management and stack
interaction, is common to both VF and PF. PF already supports reset
functionality to handle the network stack watchdog timeout trigger
but the existing code is not generic enough to be used to support VF
reset as well.
This patch does following:
1. Makes the existing watchdog timeout handler in enet layer generic
i.e. suitable for both VF and PF and
2. Introduces the new reset event handler for the VF code.
3. Changes existing reset event handler of PF code to initialize the
reset level
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we change the update rate of int_gl from every interrupt to every
one hundred interrupts, the old way to get time interval by int_gl value
is not accurate. This patch calculates the time interval using the jiffies
value.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt coalescing self-adaptive function updates the int_gl every
interrupt. The GL update rate is too faster to get a better new GL value.
This patch changes the GL update rate to every one hundred interrupts.
The GL update rate is defined by HNS3_INT_ADAPT_DOWN_START.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan table in hardware is clear after PF/Core/IMP/Global
reset, which will cause vlan tagged packets not being received
problem.
This patch fixes it by restoring the vlan table after reset.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original skb->truesize reports the received packet size,
not the actual buffer size NIC driver allocated(1 Page).
The linux net protocol will misjudge the true size of rx queue.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function of dev_close and dev_open is just likes ifconfig <netif> down
and ifconfig <netif> up. The ipv6 address will be lost after dev_close and
dev_open are called. This patch uses hns3_nic_net_stop to replace dev_close
and uses hns3_nic_net_open to replace dev_open.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is in initial state, the mac_vlan table table is empty.
So the delete operation for mac address must fail. Existence check
is needed here. Otherwise, the error message will make user confused.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the coalesce configuation lost problem when
setting the channel number by restoring all vectors's coalesce
configuation to vector 0's, because all vectors belonging to
the same netdev have the same coalesce configuation for now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refoctors the coalesce related struct by introducing
the hns3_enet_coalesce struct, in order to fix the coalesce
configuation lost problem when changing the channel number.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coalesce configuration will be set to default value by
hns3_nic_init_vector_data during reset, which causes the
coalesce configuration loss problem.
This patch fixes it by setting the default value in
hns3_nic_alloc_vector_data, which will not be called in the
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a get_vector function, which allocate the vectors
for a client, but there is not a put_vector to free the
vector.
This patch introduces the put_vector function in order to
fix the coalesce configuration lost problem during reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns3_set_ringparam, hns3_uninit_all_ring frees the
memory pointed by priv->ring_data[i].ring, and
hns3_change_all_ring_bd_num use that pointer without mallocing,
which will cause a use-after-free problem.
The patch fixes it by not freeing the memory in
hns3_uninit_all_ring, and uses hns3_put_ring_config to free it
when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver should alloc netdev with max support ring num, as
driver support change netdev count by ethtool -L.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spaces were mistakenly used instead of tabs in some of the code related
to reset functionality, which caused checkpatch.pl errors. These were
missed earlier so fixing them now.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's necessary to check hook whether being defined before
calling, improve the reliability.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local variable "changed" was defined to indicates features changed,
but was used only for feature NETIF_F_HW_VLAN_CTAG_RX. Add checking
for other features.
Fixes: 052ece6dc1 ("net: hns3: add ethtool related offload command")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the int_gl_idx does not be set, the default interrupt coalesce index
is 0. The TX queues and the RX queues will both use the GL0 as the
interrupt coalesce GL switch. But it should be GL1 for TX queues and GL0
for RX queues.
This patch adds the int_gl_idx setup for TX queues and RX queues.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the TX GL and the RX GL need to be set separately,
hns3_set_vector_coalesc_gl() has been replaced with
hns3_set_vector_coalesce_rx_gl() and hns3_set_vector_coalesce_tx_gl().
This patch removes hns3_set_vector_coalesc_gl().
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GL update function uses the max GL value between tx_int_gl and
rx_int_gl to set both new tx_int_gl and new rx_int_gl. Therefore, User
can not enable TX GL self-adaptive or RX GL self-adaptive individually.
This patch refactors the code to update the TX GL and the RX GL
separately, making user can enable TX GL self-adaptive or RX GL
self-adaptive individually.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hardware, the coalesce configurable registers include GL0, GL1,
GL2. In the driver, the TX queues use the register GL1 and the RX queues
use the register GL0. This function initializes the configuration of the
interrupt coalescing, but does not distinguish between the TX direction
and the RX direction. It will cause some confusion.
This patch refactors the function to initialize the TX GL and the RX GL
separately. And the initialization of related variables also is added to
this patch.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ethtool_ops.set_coalesce support to PF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function type should be on the same line with the function
name, or it may cause display error if a patch edit the
function. There is am example following:
https://www.spinics.net/lists/netdev/msg476141.html
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when changing MTU, The new MTU must need to be set to netdevice.
Fixes: a8e8b7ff35 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>