Provide a flags field for clocks under the ingenic-cgu driver,
which can be used to set generic common clock framework flags
on the created clocks. For example, the CLK_IS_CRITICAL flag
is needed for some clocks (such as CPU or memory) to stop them
being automatically disabled.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220428164454.17908-2-aidanmacdonald.0x0@gmail.com
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> # On X1000 and X1830
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Two fixes in one:
- In the "impose hardware constraints" block, the "logical" divider
value (aka. not translated to the hardware) was clamped to fit in the
register area, but this totally ignored the fact that the divider
value can itself have a fixed divider.
- The code that made sure that the divider value returned by the
function was a multiple of its own fixed divider could result in a
wrong value being calculated, because it was rounded down instead of
rounded up.
Fixes: 4afe2d1a6e ("clk: ingenic: Allow divider value to be divided")
Co-developed-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211001172033.122329-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SoC-specific code can now provide a callback if they need to compute the
M/N/OD values in a specific way.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: 周琰杰 (Zhou Yanjie)<zhouyanjie@wanyeetech.com> # on CU1000-neo/X1000E
Link: https://lore.kernel.org/r/20210530164923.18134-6-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We can express that a PLL has no bypass bit by simply setting the
.bypass_bit field to a negative value.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210530164923.18134-5-paul@crapouillou.net
Tested-by: 周琰杰 (Zhou Yanjie)<zhouyanjie@wanyeetech.com> # on CU1830-neo/X1830
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Rework the clock code so that the bypass register is only read when
there is actually a bypass functionality.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210530164923.18134-4-paul@crapouillou.net
Tested-by: 周琰杰 (Zhou Yanjie)<zhouyanjie@wanyeetech.com> # on CU1830-neo/X1830
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When a clock is declared as both CGU_CLK_DIV and CGU_CLK_MUX, the CGU
code expects the mux to be applied first, the divider second.
On the JZ4760, and maybe on some other SoCs, some clocks also have a mux
setting and a divider, but the divider is not applied to all parents
selectable from the mux.
This could be solved by creating two clocks, one with CGU_CLK_DIV and
one with CGU_CLK_MUX, but that would increase the number of clocks.
Instead, add a 8-bit mask to CGU_CLK_DIV clocks. If the bit
corresponding to the parent clock's index is set, the divider is
bypassed.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210530164923.18134-3-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The previous code assumed that a higher hardware value always resulted
in a bigger divider, which is correct for the regular clocks, but is
an invalid assumption when a divider table is provided for the clock.
Perfect example of this is the PLL0_HALF clock, which applies a /2
divider with the hardware value 0, and a /1 divider otherwise.
Fixes: a9fa2893fc ("clk: ingenic: Add support for divider tables")
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201212135733.38050-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clocks that don't have a divider are in our case all marked with the
CLK_SET_RATE_PARENT flag. In this case, the .round_rate implementation
should modify the value pointed to by parent_rate, in order to propagate
the rate change to the parent, as explained in the documentation of
clk_set_rate().
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-5-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The custom clocks have custom functions to round, get or set their rate.
Therefore, we can't assume that they need the CLK_SET_RATE_PARENT flag.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-4-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CLK_SET_RATE_GATE means that the clock must be gated when being
reclocked. This is not the case for the PLLs in Ingenic SoCs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-3-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use the readl_poll_timeout() function instead of rolling our own
busy-wait loops. This makes the code simpler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-2-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The to_clk_info() previously had a BUG_ON() to check that it was only
called for PLL clocks. Yet, all the other clocks were doing the exact
same thing the macro does, in-line.
Move the to_clk_info() macro to the top of the file, remove the
hardcoded BUG_ON(), and use it everywhere it makes sense.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903015048.3091523-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The PLL of X1830 Soc from Ingenic has been greatly changed,
the bypass control is placed in another register, so now two
registers may needed to control the PLL. To this end, a new
"bypass_reg" was introduced. In addition, when calculating
rate, the PLL of X1830 introduced an extra 2x multiplier,
so a new "rate_multiplier" was introduced. And adjust the
code in jz47xx-cgu.c and x1000-cgu.c, make it to be
compatible with the new cgu code.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It is not necessary to use spinlock when reading registers,
so remove it from cgu.c.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Suggested-by: Paul Burton <paulburton@kernel.org>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
Some clocks provided on Ingenic SoCs have dividers, whose hardware value
as written in the register cannot be expressed as an affine function
to the actual divider value.
For instance, for the CPU clock on the JZ4770, the dividers are coded as
follows:
------------------
| Bits | Div |
------------------
| 0 0 0 | 1 |
| 0 0 1 | 2 |
| 0 1 0 | 3 |
| 0 1 1 | 4 |
| 1 0 0 | 6 |
| 1 0 1 | 8 |
| 1 1 0 | 12 |
------------------
To support this setup, we introduce a new field in the
ingenic_cgu_div_info structure that allows to specify the divider table.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/clk/ingenic/cgu.c: In function 'ingenic_pll_recalc_rate':
drivers/clk/ingenic/cgu.c:86:15: warning:
variable 'enable' set but not used [-Wunused-but-set-variable]
It's not used after commit ab27eb4bc3 ("clk: ingenic: Add code to
enable/disable PLLs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Take a parent rate of 180 MHz, and a requested rate of 4.285715 MHz.
This results in a theorical divider of 41.999993 which is then rounded
up to 42. The .round_rate function would then return (180 MHz / 42) as
the clock, rounded down, so 4.285714 MHz.
Calling clk_set_rate on 4.285714 MHz would round the rate again, and
give a theorical divider of 42,0000028, now rounded up to 43, and the
rate returned would be (180 MHz / 43) which is 4.186046 MHz, aka. not
what we requested.
Fix this by rounding up the divisions.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some clocks need a small delay after being ungated to run stable, as
using them too soon might result in hardware lockups.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Support the clocks which are gated when their gate bit is cleared
instead of set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This commit permits the PLLs to be dynamically enabled and disabled when
their children clocks are enabled and disabled.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18480/
Signed-off-by: James Hogan <jhogan@kernel.org>
The second PLL of the JZ4770 does not have a bypass bit.
This commit makes it possible to support it with the current common CGU
code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18479/
Signed-off-by: James Hogan <jhogan@kernel.org>
Previously, the clocks with a fixed divider would report their rate
as being the same as the one of their parent, independently of the
divider in use. This commit fixes this behaviour.
This went unnoticed as neither the jz4740 nor the jz4780 CGU code
have clocks with fixed dividers yet.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18477/
Signed-off-by: James Hogan <jhogan@kernel.org>
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The JZ4780's MSC clock divider registers multiply the clock divider by 2.
This means that MMC devices run at half their expected speed. Add the
ability to divide the clock divider in order to solve this.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock provider uses the consumer API, so include clk.h
explicitly.
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver supports the CGU clocks for Ingenic SoCs. It is generic
enough to be usable across at least the JZ4740 to the JZ4780, and will
be made use of on such devices in subsequent commits. This patch by
itself only adds the SoC-agnostic infrastructure that forms the bulk of
the CGU driver for the aforementioned further commits to make use of.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Co-authored-by: Paul Cercueil <paul@crapouillou.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10150/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Aidan MacDonald