After 90eff9096c ("net: phy: Allow splitting MDIO bus/device support
from PHYs") the various MDIO bus drivers were no longer parented with
config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix
this by depending on MDIO_DEVICE which is a menuconfig.
This is visually nicer and less confusing for users.
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the original patch network starts to crash on heavy load.
It's not fully clear why this additional register read has such side
effects, but removing it fixes the issue.
Thanks also to Alex for his contribution and hints.
[0] https://marc.info/?t=155268170400002&r=1&w=2
Fixes: e782410ed2 ("r8169: improve spurious interrupt detection")
Reported-by: VDR User <user.vdr@gmail.com>
Tested-by: VDR User <user.vdr@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is only one byte in a frag, the current calculation
using "(size + HNS3_MAX_BD_SIZE - 1) >> HNS3_MAX_BD_SIZE_OFFSET"
will return zero, because HNS3_MAX_BD_SIZE is 65535 and
HNS3_MAX_BD_SIZE_OFFSET is 16. So it will cause tx error when
a frag's size is one byte.
This patch fixes it by using DIV_ROUND_UP.
Fixes: 3fe13ed95d ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands if a shrink is delayed because of an outstanding
rehash, we will go into a rescheduling loop without ever doing
the rehash.
This patch fixes this by still carrying out the rehash and then
rescheduling so that we can shrink after the completion of the
rehash should it still be necessary.
The return value of EEXIST captures this case and other cases
(e.g., another thread expanded/rehashed the table at the same
time) where we should still proceed with the rehash.
Fixes: da20420f83 ("rhashtable: Add nested tables")
Reported-by: Josh Elsasser <jelsasser@appneta.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Josh Elsasser <jelsasser@appneta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti says:
====================
net/sched: validate the control action with all the other parameters
currently, the kernel checks for bad values of the control action in
tcf_action_init_1(), after a successful call to the action's init()
function. When the control action is 'goto chain', this causes two
undesired behaviors:
1. "misconfigured action after replace that causes kernel crash":
if users replace a valid TC action with another one having invalid
control action, all the new configuration data (including the bad
control action) are applied successfully, even if the kernel returned
an error. As a consequence, it's possible to trigger a NULL pointer
dereference in the traffic path of every TC action (1), replacing the
control action with 'goto chain x', when chain <x> doesn't exist.
2. "refcount leak that makes kmemleak complain"
when a valid 'goto chain' action is overwritten with another action,
the kernel forgets to decrease refcounts in the chain.
The above problems can be fixed if we validate the control action in each
action's init() function, the same way as we are already doing for all the
other configuration parameters.
Now that chains can be released after an action is replaced, we need to
care about concurrent access of 'goto_chain' pointer: ensure we access it
through RCU, like we did with most action-specific configuration parameters.
- Patch 1 removes the wrong checks and provides functions that can be
used to properly validate control actions in individual actions
- Patch 2 to 16 fix individual actions, and add TDC selftest code to
verify the correct behavior (2)
- Patch 17 and 18 fix concurrent access issues on 'goto_chain', that can be
observed after the chain refcount leak is fixed.
Changes since v1:
- reword the cover letter
- condense the extack message in case tc_action_check_ctrlact() is called
with invalid parameters.
- add tcf_action_set_ctrlact() to avoid code duplication an make the
RCU-ification of 'goto_chain' easier.
- fix errors in act_ife, act_simple, act_skbedit, and avoid useless 'goto
end' in act_connmark, thanks a lot to Vlad Buslov.
- avoid dereferencing 'goto_chain' in tcf_gact_goto_chain_index(), so
we don't have to care about the grace period there.
- let actions respect the grace period when they release chains, thanks
to Cong Wang and Vlad Buslov.
Changes since RFC:
- include a fix for all TC actions
- add a selftest for each TC action
- squash fix for refcount leaks into a single patch, the first in the
series, thanks to Cong Wang
- ensure that chain refcount is released without tcfa_lock held, thanks
to Vlad Buslov
Notes:
(1) act_ipt didn't need any fix, as the control action is constantly equal
to TC_ACT_OK.
(2) the selftest for act_simple fails because userspace tc backend for
'simple' does not parse the control action correctly (and hardcodes it
to TC_ACT_PIPE).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
use RCU when accessing the action chain, to avoid use after free in the
traffic path when 'goto chain' is replaced on existing TC actions (see
script below). Since the control action is read in the traffic path
without holding the action spinlock, we need to explicitly ensure that
a->goto_chain is not NULL before dereferencing (i.e it's not sufficient
to rely on the value of TC_ACT_GOTO_CHAIN bits). Not doing so caused NULL
dereferences in tcf_action_goto_chain_exec() when the following script:
# tc chain add dev dd0 chain 42 ingress protocol ip flower \
> ip_proto udp action pass index 4
# tc filter add dev dd0 ingress protocol ip flower \
> ip_proto udp action csum udp goto chain 42 index 66
# tc chain del dev dd0 chain 42 ingress
(start UDP traffic towards dd0)
# tc action replace action csum udp pass index 66
was run repeatedly for several hours.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
callers of tcf_gact_goto_chain_index() can potentially read an old value
of the chain index, or even dereference a NULL 'goto_chain' pointer,
because 'goto_chain' and 'tcfa_action' are read in the traffic path
without caring of concurrent write in the control path. The most recent
value of chain index can be read also from a->tcfa_action (it's encoded
there together with TC_ACT_GOTO_CHAIN bits), so we don't really need to
dereference 'goto_chain': just read the chain id from the control action.
Fixes: e457d86ada ("net: sched: add couple of goto_chain helpers")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- pass a pointer to struct tcf_proto in each actions's init() handler,
to allow validating the control action, checking whether the chain
exists and (eventually) refcounting it.
- remove code that validates the control action after a successful call
to the action's init() handler, and replace it with a test that forbids
addition of actions having 'goto_chain' and NULL goto_chain pointer at
the same time.
- add tcf_action_check_ctrlact(), that will validate the control action
and eventually allocate the action 'goto_chain' within the init()
handler.
- add tcf_action_set_ctrlact(), that will assign the control action and
swap the current 'goto_chain' pointer with the new given one.
This disallows 'goto_chain' on actions that don't initialize it properly
in their init() handler, i.e. calling tcf_action_check_ctrlact() after
successful IDR reservation and then calling tcf_action_set_ctrlact()
to assign 'goto_chain' and 'tcf_action' consistently.
By doing this, the kernel does not leak anymore refcounts when a valid
'goto chain' handle is replaced in TC actions, causing kmemleak splats
like the following one:
# tc chain add dev dd0 chain 42 ingress protocol ip flower \
> ip_proto tcp action drop
# tc chain add dev dd0 chain 43 ingress protocol ip flower \
> ip_proto udp action drop
# tc filter add dev dd0 ingress matchall \
> action gact goto chain 42 index 66
# tc filter replace dev dd0 ingress matchall \
> action gact goto chain 43 index 66
# echo scan >/sys/kernel/debug/kmemleak
<...>
unreferenced object 0xffff93c0ee09f000 (size 1024):
comm "tc", pid 2565, jiffies 4295339808 (age 65.426s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 08 00 06 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<000000009b63f92d>] tc_ctl_chain+0x3d2/0x4c0
[<00000000683a8d72>] rtnetlink_rcv_msg+0x263/0x2d0
[<00000000ddd88f8e>] netlink_rcv_skb+0x4a/0x110
[<000000006126a348>] netlink_unicast+0x1a0/0x250
[<00000000b3340877>] netlink_sendmsg+0x2c1/0x3c0
[<00000000a25a2171>] sock_sendmsg+0x36/0x40
[<00000000f19ee1ec>] ___sys_sendmsg+0x280/0x2f0
[<00000000d0422042>] __sys_sendmsg+0x5e/0xa0
[<000000007a6c61f9>] do_syscall_64+0x5b/0x180
[<00000000ccd07542>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<0000000013eaa334>] 0xffffffffffffffff
Fixes: db50514f9a ("net: sched: add termination action to allow goto chain")
Fixes: 97763dc0f4 ("net_sched: reject unknown tcfa_action values")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both PCLK and HCLK are "required" clocks according to macb devicetree
documentation. There is a chance that devm_clk_get doesn't return a
negative error but just a NULL clock structure instead. In such a case
the driver proceeds as usual and uses pclk value 0 to calculate MDC
divisor which is incorrect. Hence fix the same in clock initialization.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.
The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.
http://www.ti.com/lit/gpn/dp83825i
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree:
1) Remove a direct dependency with IPv6 introduced by the
sip_external_media feature, from Alin Nastac.
2) Fix bogus ENOENT when removing interval elements from set.
3) Set transport_header from br_netfilter to mimic the stack
behaviour, this partially fixes a checksum validation bug
from the SCTP connection tracking, from Xin Long.
4) Fix undefined reference to symbol in xt_TEE, due to missing
Kconfig dependencies, from Arnd Bergmann.
5) Check for NULL in skb_header_pointer() calls in ip6t_shr,
from Kangjie Lu.
6) Fix bogus EBUSY when removing an existing conntrack helper from
a transaction.
7) Fix module autoload of the redirect extension.
8) Remove duplicated transition in flowtable diagram in the existing
documentation.
9) Missing .release_ops call from error path in newrule() which
results module refcount leak, from Taehee Yoo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In genl_register_family(), when idr_alloc() fails,
we forget to free the memory we possibly allocate for
family->attrbuf.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2ae0f17df1 ("genetlink: use idr to track families")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cancelling a subscription, we have to clear the cancel bit in the
request before iterating over any established subscriptions with memcmp.
Otherwise no subscription will ever be found, and it will not be
possible to explicitly unsubscribe individual subscriptions.
Fixes: 8985ecc7c1 ("tipc: simplify endianness handling in topology subscriber")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we don't try to enqueue XDP_REDIRECT frames to an
inexistent FQ.
While it is guaranteed not to have more than one queue per core,
having fewer queues than CPUs on an interface is a valid
configuration.
Fixes: d678be1dc1 ("dpaa2-eth: add XDP_REDIRECT support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lukas Wunner says:
====================
ks8851 fixes & cleanups
Four fixes and two cleanups for the Microchip (formerly Micrel) KSZ8851
SPI Ethernet driver.
Some of the fixes might even pass as stable material, but I haven't marked
them as such for cautiousness: Doesn't hurt letting them bake in linux-next
for a few weeks to raise the confidence, even though we've tested them
extensively on our Revolution Pi open source PLCs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851 chip is sold either with an SPI interface (KSZ8851SNL) or
with a so-called non-PCI interface (KSZ8851-16MLL). When the driver
for the latter was introduced with commit a55c0a0ed4 ("drivers/net:
ks8851_mll ethernet network driver"), it duplicated the register macros
introduced by the driver for the former with commit 3ba81f3ece ("net:
Micrel KS8851 SPI network driver").
The chips are almost identical, so the duplication seems unwarranted.
There are a handful of bits which are in use on the KSZ8851-16MLL but
reserved on the KSZ8851SNL, and vice-versa, but there are no actual
collisions.
Thus, remove the duplicate definitions from the KSZ8851-16MLL driver.
Mark all bits which differ between the two chips. Move the SPI frame
opcodes, which are specific to KSZ8851SNL, to its driver.
The KSZ8851-16MLL driver added a RXFCTR_THRESHOLD_MASK macro which is a
duplication of the RXFCTR_RXFCT_MASK macro, rename it where it's used.
Same for P1MBCR_FORCE_FDX, which duplicates the BMCR_FULLDPLX macro and
OBCR_ODS_16MA, which duplicates OBCR_ODS_16mA.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the header file accompanying the ks8851 driver, the P1SCLMD register
macros are misnamed, they actually pertain to the P1CR register.
The P1CR macros in turn pertain to the P1SR register, see pages 65 to 68
of the spec:
http://www.hqchip.com/uploads/pdf/201703/47c98946d6c97a4766e14db3f24955f2.pdf
The misnomers have no negative consequences so far because the macros
aren't used by ks8851.c, but that's about to change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.
The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.
The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851 driver currently requests the IRQ before registering the
net_device. Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present. Most other drivers delay
requesting the IRQ until the net_device is opened. Do the same.
The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 73fdeb82e9 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.
However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").
However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management: On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.
The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.
Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.
The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sctp_setsockopt_bindx()/__sctp_setsockopt_connectx(), it allocates
memory with addrs_size which is passed from userspace. We used flag
GFP_USER to put some more restrictions on it in Commit cacc062152
("sctp: use GFP_USER for user-controlled kmalloc").
However, since Commit c981f254cc ("sctp: use vmemdup_user() rather
than badly open-coding memdup_user()"), vmemdup_user() has been used,
which doesn't check GFP_USER flag when goes to vmalloc_*(). So when
addrs_size is a huge value, it could exhaust memory and even trigger
oom killer.
This patch is to use memdup_user() instead, in which GFP_USER would
work to limit the memory allocation with a huge addrs_size.
Note we can't fix it by limiting 'addrs_size', as there's no demand
for it from RFC.
Reported-by: syzbot+ec1b7575afef85a0e5ca@syzkaller.appspotmail.com
Fixes: c981f254cc ("sctp: use vmemdup_user() rather than badly open-coding memdup_user()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jianlin reported a crash:
[ 381.484332] BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
[ 381.619802] RIP: 0010:fib6_rule_lookup+0xa3/0x160
[ 382.009615] Call Trace:
[ 382.020762] <IRQ>
[ 382.030174] ip6_route_redirect.isra.52+0xc9/0xf0
[ 382.050984] ip6_redirect+0xb6/0xf0
[ 382.066731] icmpv6_notify+0xca/0x190
[ 382.083185] ndisc_redirect_rcv+0x10f/0x160
[ 382.102569] ndisc_rcv+0xfb/0x100
[ 382.117725] icmpv6_rcv+0x3f2/0x520
[ 382.133637] ip6_input_finish+0xbf/0x460
[ 382.151634] ip6_input+0x3b/0xb0
[ 382.166097] ipv6_rcv+0x378/0x4e0
It was caused by the lookup function __ip6_route_redirect() returns NULL in
fib6_rule_lookup() when ip6_create_rt_rcu() returns NULL.
So we fix it by simply making ip6_create_rt_rcu() return ip6_null_entry
instead of NULL.
v1->v2:
- move down 'fallback:' to make it more readable.
Fixes: e873e4b9cc ("ipv6: use fib6_info_hold_safe() when necessary")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
->release_ops() callback releases resources and this is used in error path.
If nf_tables_newrule() fails after ->select_ops(), it should release
resources. but it can not call ->destroy() because that should be called
after ->init().
At this point, ->release_ops() should be used for releasing resources.
Test commands:
modprobe -rv xt_tcpudp
iptables-nft -I INPUT -m tcp <-- error command
lsmod
Result:
Module Size Used by
xt_tcpudp 20480 2 <-- it should be 0
Fixes: b8e2040063 ("netfilter: nft_compat: use .release_ops and remove list of extension")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds support for 6PE (RFC 4798) which uses IPv4-mapped IPv6
nexthop to connect IPv6 islands over IPv4 only MPLS network core.
Prior to this fix, to find the link-layer destination mac address, 6PE
enabled host/router was sending IPv6 ND requests for IPv4-mapped IPv6
nexthop address over the interface facing the IPv4 only core which
wouldn't success as the core is IPv6 free.
This fix changes that behavior on 6PE host to treat the nexthop as IPv4
address and send ARP requests whenever the next-hop address is an
IPv4-mapped IPv6 address.
Below topology illustrates the issue and how the patch addresses it.
abcd::1.1.1.1 (lo) abcd::2.2.2.2 (lo)
R0 (PE/host)------------------------R1--------------------------------R2 (PE/host)
<--- IPv4 MPLS core ---> <------ IPv4 MPLS core -------->
eth1 eth2 eth3 eth4
172.18.0.10 172.18.0.11 172.19.0.11 172.19.0.12
ffff::172.18.0.10 ffff::172.19.0.12
<------------------IPv6 MPLS tunnel ---------------------->
R0 and R2 act as 6PE routers of IPv6 islands. R1 is IPv4 only with MPLS tunnels
between R0,R1 and R1,R2.
docker exec r0 ip -f inet6 route add abcd::2.2.2.2/128 nexthop encap mpls 100 via ::ffff:172.18.0.11 dev eth1
docker exec r2 ip -f inet6 route add abcd::1.1.1.1/128 nexthop encap mpls 200 via ::ffff:172.19.0.11 dev eth4
docker exec r1 ip -f mpls route add 100 via inet 172.19.0.12 dev eth3
docker exec r1 ip -f mpls route add 200 via inet 172.18.0.10 dev eth2
With the change, when R0 sends an IPv6 packet over MPLS tunnel to abcd::2.2.2.2,
using ::ffff:172.18.0.11 as the nexthop, it does neighbor discovery for
172.18.18.0.11.
Signed-off-by: Vinay K Nallamothu <nvinay@juniper.net>
Tested-by: Avinash Lingala <ar977m@att.com>
Tested-by: Aravind Srinivas Srinivasa Prabhakar <aprabh@juniper.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang points out a harmless signed integer overflow:
drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~
drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
Make the variable unsigned to avoid the overflow.
Fixes: Linux-2.1.128pre1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dual stack dccp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or
inet6_iif() helper.
Fixes: 3df80d9320 ("[DCCP]: Introduce DCCPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dual stack tcp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or tcp_v6_iif() helper.
Fixes: 1397ed35f2 ("ipv6: add flowinfo for tcp6 pkt_options for all cases")
Fixes: df3687ffc6 ("ipv6: add the IPV6_FL_F_REFLECT flag to IPV6_FL_A_GET")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of kmemdup failure while setting the service name the patch
returns -ENOMEM upstream for processing.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdev_queue_add_kobject and rx_queue_add_kobject,
if sysfs_create_group failed, kobject_put will call
netdev_queue_release to decrease dev refcont, however
dev_hold has not be called. So we will see this while
unregistering dev:
unregister_netdevice: waiting for bcsh0 to become free. Usage count = -1
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d0d6683716 ("net: don't decrement kobj reference count on init failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using 16K DMA buffers and ring mode, the DES3 refill is not working
correctly as the function is using a bogus pointer for checking the
private data. As a result stale pointers will remain in the RX descriptor
ring, so DMA will now likely overwrite/corrupt some already freed memory.
As simple reproducer, just receive some UDP traffic:
# ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up
# iperf3 -c 192.168.253.40 -u -b 0 -R
If you didn't crash by now check the RX descriptors to find non-contiguous
RX buffers:
cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status
[...]
1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e
^^^^^^^^^^^^^^^^^^^^^
2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e
^^^^^^^^^^^^^^^^^^^^^
A simple ping test will now report bad data:
# ping -s 8200 192.168.253.40
PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data.
8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms
wrong data byte #8144 should be 0xd0 but was 0x88
Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer
size is 16K.
Fixes: 54139cf3bb ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recently added function in mlxsw triggers a harmless compiler warning:
In file included from drivers/net/ethernet/mellanox/mlxsw/core.h:17,
from drivers/net/ethernet/mellanox/mlxsw/core_env.c:7:
drivers/net/ethernet/mellanox/mlxsw/core_env.c: In function 'mlxsw_env_module_temp_thresholds_get':
drivers/net/ethernet/mellanox/mlxsw/reg.h:8015:45: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
#define MLXSW_REG_MTMP_TEMP_TO_MC(val) (val * 125)
~~~~~^~~~~~
drivers/net/ethernet/mellanox/mlxsw/core_env.c:116:8: note: in expansion of macro 'MLXSW_REG_MTMP_TEMP_TO_MC'
if (!MLXSW_REG_MTMP_TEMP_TO_MC(module_temp)) {
^~~~~~~~~~~~~~~~~~~~~~~~~
The warning is normally disabled, but it would be nice to enable
it to find real bugs, and there are no other known instances at
the moment.
Replace the negation with a zero-comparison, which also matches
the comment above it.
Fixes: d93c19a1d9 ("mlxsw: core: Add API for QSFP module temperature thresholds reading")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for 5.1. Lots of fixes for mt76 this time.
iwlwifi
* fix warning with do_div()
mt7601u
* avoid using hardware which is supported by mt76
mt76
* more fixes for hweight8() usage
* fix hardware restart for mt76x2
* fix writing txwi on USB devices
* fix (and disable by default) ED/CCA support on 76x2
* fix powersave issues on 7603
* fix return value check for ioremap on 7603
* fix duplicate USB device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJckUDJAAoJEG4XJFUm622bLuAH/jlK2kVoF6nEweiLZ/HdAvBm
H0pafLzs7f59otaIXoA4uY81CTyhL3YIthw5UdQH55kzMgK0TXNMm37jqg4e1jJX
JWCYwGvMB6Jzohu8zZNN0POc2IVzZnCnQgY0hgl5+861N09Zc9cCTr9wzZ/L1yU2
FXz0dfc2SKVRYszEkWjNTNaa/fyaJYvgFKJV58sKKOCy45JLGnIQS1YpzsDhDgrW
khjlqFJWEY2kwD2ka6xMJHkF515FciEz64eSB+wTYicLsQyfGV38M6RDPX5jsYPK
2+siTaBf7Srw4+g4S4semqFT7ZVbDW3+tCKnufJu+hfLjrPAwsp8QWnk4p9+M0k=
=da1Z
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-03-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
First set of fixes for 5.1. Lots of fixes for mt76 this time.
iwlwifi
* fix warning with do_div()
mt7601u
* avoid using hardware which is supported by mt76
mt76
* more fixes for hweight8() usage
* fix hardware restart for mt76x2
* fix writing txwi on USB devices
* fix (and disable by default) ED/CCA support on 76x2
* fix powersave issues on 7603
* fix return value check for ioremap on 7603
* fix duplicate USB device IDs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli