Remote TLB flush does a busy wait which is fine in bare-metal
scenario. But with-in the guest, the vcpus might have been pre-empted or
blocked. In this scenario, the initator vcpu would end up busy-waiting
for a long amount of time; it also consumes CPU unnecessarily to wake
up the target of the shootdown.
This patch set adds support for KVM's new paravirtualized TLB flush;
remote TLB flush does not wait for vcpus that are sleeping, instead
KVM will flush the TLB as soon as the vCPU starts running again.
The improvement is clearly visible when the host is overcommitted; in this
case, the PV TLB flush (in addition to avoiding the wait on the main CPU)
prevents preempted vCPUs from stealing precious execution time from the
running ones.
Testing on a Xeon Gold 6142 2.6GHz 2 sockets, 32 cores, 64 threads,
so 64 pCPUs, and each VM is 64 vCPUs.
ebizzy -M
vanilla optimized boost
1VM 46799 48670 4%
2VM 23962 42691 78%
3VM 16152 37539 132%
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This adds a register identifier for use with the one_reg interface
to allow the decrementer expiry time to be read and written by
userspace. The decrementer expiry time is in guest timebase units
and is equal to the sum of the decrementer and the guest timebase.
(The expiry time is used rather than the decrementer value itself
because the expiry time is not constantly changing, though the
decrementer value is, while the guest vcpu is not running.)
Without this, a guest vcpu migrated to a new host will see its
decrementer set to some random value. On POWER8 and earlier, the
decrementer is 32 bits wide and counts down at 512MHz, so the
guest vcpu will potentially see no decrementer interrupts for up
to about 4 seconds, which will lead to a stall. With POWER9, the
decrementer is now 56 bits side, so the stall can be much longer
(up to 2.23 years) and more noticeable.
To help work around the problem in cases where userspace has not been
updated to migrate the decrementer expiry time, we now set the
default decrementer expiry at vcpu creation time to the current time
rather than the maximum possible value. This should mean an
immediate decrementer interrupt when a migrated vcpu starts
running. In cases where the decrementer is 32 bits wide and more
than 4 seconds elapse between the creation of the vcpu and when it
first runs, the decrementer would have wrapped around to positive
values and there may still be a stall - but this is no worse than
the current situation. In the large-decrementer case, we are sure
to get an immediate decrementer interrupt (assuming the time from
vcpu creation to first run is less than 2.23 years) and we thus
avoid a very long stall.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The reason I added this documentation originally was that the concept of
"never taking the interrupt", but just use the timer to generate an exit
from the guest, was confusing to most, and we had to explain it several
times over. But as we can clearly see, we've failed to update the
documentation as the code has evolved, and people who need to understand
these details are probably better off reading the code.
Let's lighten our maintenance burden slightly and just get rid of this.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Old kernels did not check for zero in the irq_state.flags field and old
QEMUs did not zero the flag/reserved fields when calling
KVM_S390_*_IRQ_STATE. Let's add comments to prevent future uses of
these fields.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
If hardware supports memory encryption then KVM_MEMORY_ENCRYPT_REG_REGION
and KVM_MEMORY_ENCRYPT_UNREG_REGION ioctl's can be used by userspace to
register/unregister the guest memory regions which may contain the encrypted
data (e.g guest RAM, PCI BAR, SMRAM etc).
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
If the hardware supports memory encryption then the
KVM_MEMORY_ENCRYPT_OP ioctl can be used by qemu to issue a platform
specific memory encryption commands.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaBYxhAAoJEEtpOizt6ddyOc4H/1qADSdnZFVVE5v15Y+E8HLv
EOXAo/yYJg26fY/TBIXo7gxSZFCd0Ah703aucPGTRFyOb8t0VqIvI07rS1u4sKPp
mxfidYIZwLMibgno8NBdWB2mFeXrNlWTmwNt/IoO0iMn7IGqQZ/FZdf3GmWEVEsG
CU/DrQRXArJqS77NuZtkhhZOKBxB0lQNv52DkVgy/QlcBagAI14hbezkLQAco4oT
NUC4GyXn9yHzpTfhuQXv5hLd4xCqg9e51OgYNSL9oC/JXSByd7edQuqpd4fmnG4Y
qoDPJ11wmkuUKEDaGbC7nZWIaiVc/TfJy2Hwj3bUVwQFbopCeYhQqCDUSKftncA=
=o4u7
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-gicv4-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
GICv4 Support for KVM/ARM for v4.15
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
- merge of the sthyi tree from the base s390 team, which moves the sthyi
out of KVM into a shared function also for non-KVM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=9mW5
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux
KVM: s390: fixes and improvements for 4.15
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
- merge of the sthyi tree from the base s390 team, which moves the sthyi
out of KVM into a shared function also for non-KVM
The GICv4 architecture doesn't make it easy for save/restore to
work, as it doesn't give any guarantee that the pending state
is written into the pending table.
So let's not take any chance, and let's return an error if
we encounter any LPI that has the HW bit set. In order for
userspace to distinguish this error from other failure modes,
use -EACCES as an error code.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The AIS capability was introduced in 4.12, while the interface to
migrate the state was added in 4.13. Unfortunately it is not possible
for userspace to detect the migration capability without creating a flic
kvm device. As in QEMU the cpu model detection runs on the "none"
machine this will result in cpu model issues regarding the "ais"
capability.
To get the "ais" capability properly let's add a new KVM capability that
tells userspace that AIS states can be migrated.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Halil Pasic <pasic@linux.vnet.ibm.com>
There is a chance to delete not yet delivered I/O interrupts if an
exploiter uses the subsystem identification word 0x0000 while
processing a KVM_DEV_FLIC_CLEAR_IO_IRQ ioctl. -EINVAL will be returned
now instead in that case.
Classic interrupts will always have bit 0x10000 set in the schid while
adapter interrupts have a zero schid. The clear_io_irq interface is
only useful for classic interrupts (as adapter interrupts belong to
many devices). Let's make this interface more strict and forbid a schid
of 0.
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Changes include:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaAIAsAAoJEEtpOizt6ddyc04H/0WYVoLGvKtJFD+a7Sc8rwXv
a+cPaTlqQ+Y96m0FApSLDmHcIlpLOdGz2DxKW8pdpV7zM0snRdEJcrq1b2Df/sYX
MU3iQTe2Gb7QEBBH8Ub25bM5Y+TNrWtWJpOIORFnFO8MmbTfBzs/7BaGw6tI+XB6
BjCKqjh9j9zbXWi6/vvQm4clQZDu93l5NahwOa7wTKAIyCES1YGMsLX7aikqaurQ
4Vw57C11hwUBwEg61iHxj3uQN/dIF+hx2OVuxkOdwNrJw3B736lwBXDnFAhlmdbI
IHhnoGBE2jkaUwuBiIwM/WFrgNN6d3Uz6QFbYqpQEDhDypOYjL6TlR0OER6v3Ks=
=TaCO
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into next
KVM/ARM Changes for v4.15
Changes include:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
At the moment, the in-kernel emulated ITS is not properly reset.
On guest restart/reset some registers keep their old values and
internal structures like device, ITE, and collection lists are not
freed.
This may lead to various bugs. Among them, we can have incorrect state
backup or failure when saving the ITS state at early guest boot stage.
This patch documents a new attribute, KVM_DEV_ARM_ITS_CTRL_RESET in
the KVM_DEV_ARM_VGIC_GRP_CTRL group.
Upon this action, we can reset registers and especially those
pointing to tables previously allocated by the guest and free
the internal data structures storing the list of devices, collections
and lpis.
The usual approach for device reset of having userspace write
the reset values of the registers to the kernel via the register
read/write APIs doesn't work for the ITS because it has some
internal state (caches) which is not exposed as registers,
and there is no register interface for "drop cached data without
writing it back to RAM". So we need a KVM API which mimics the
hardware's reset line, to provide the equivalent behaviour to
a "pull the power cord out of the back of the machine" reset.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: wanghaibin <wanghaibin.wang@huawei.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Changing it afterwards doesn't make too much sense and will only result
in inconsistencies.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Setting it to 0 leads to setting it to the default value, let's document
this.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Two minor cleanups and improvements, a fix for decoding external abort
types from guests, and added support for migrating the active priority
of interrupts when running a GICv2 guest on a GICv3 host.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZrsRdAAoJEEtpOizt6ddyoDIH/i94Wc5Iw9mpzi99NXyDGxYb
2kEGg8uRZFuAwK49+aNVEqL7pPymlV3qdl1fdsmWM9ch9D8WOiezx5JgSd3+uriF
x2Cc6kxZQJ4/UT3laAZArVcGnQqDHdOrJIsOZ9f+UFRiFazlMVMgAJX7yQwHYiBQ
QM/z5BbLSbh+NHAv15utz85JjR8lFL7AIzPemHR6Zh7cr3XmeW3nadaYMuyqjFsZ
aYD4S+y/eRw6HkImV/DaaLv/tDrOEU2cQOqi19TvfYpx/XW4uLQA9oxS9Qd9ADZw
T8Ha5jGEthy+3mzwEmGFwTVGpbvt3TYavZ743lp230PODYOkfO+ETbIlstuYNb4=
=dIG3
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM Changes for v4.14
Two minor cleanups and improvements, a fix for decoding external abort
types from guests, and added support for migrating the active priority
of interrupts when running a GICv2 guest on a GICv3 host.
When migrating guests around we need to know the active priorities to
ensure functional virtual interrupt prioritization by the GIC.
This commit clarifies the API and how active priorities of interrupts in
different groups are represented, and implements the accessor functions
for the uaccess register range.
We live with a slight layering violation in accessing GICv3 data
structures from vgic-mmio-v2.c, because anything else just adds too much
complexity for us to deal with (it's not like there's a benefit
elsewhere in the code of an intermediate representation as is the case
with the VMCR). We accept this, because while doing v3 processing from
a file named something-v2.c can look strange at first, this really is
specific to dealing with the user space interface for something that
looks like a GICv2.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Allow for the enablement of MEF and the support for the extended
epoch in SIE and VSIE for the extended guest TOD-Clock.
A new interface is used for getting/setting a guest's extended TOD-Clock
that uses a single ioctl invocation, KVM_S390_VM_TOD_EXT. Since the
host time is a moving target that might see an epoch switch or STP sync
checks we need an atomic ioctl and cannot use the exisiting two
interfaces. The old method of getting and setting the guest TOD-Clock is
still retained and is used when the old ioctls are called.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Hyper-V identifies vCPUs by Virtual Processor Index, which can be
queried via HV_X64_MSR_VP_INDEX msr. It is defined by the spec as a
sequential number which can't exceed the maximum number of vCPUs per VM.
APIC ids can be sparse and thus aren't a valid replacement for VP
indices.
Current KVM uses its internal vcpu index as VP_INDEX. However, to make
it predictable and persistent across VM migrations, the userspace has to
control the value of VP_INDEX.
This patch achieves that, by storing vp_index explicitly on vcpu, and
allowing HV_X64_MSR_VP_INDEX to be set from the host side. For
compatibility it's initialized to KVM vcpu index. Also a few variables
are renamed to make clear distinction betweed this Hyper-V vp_index and
KVM vcpu_id (== APIC id). Besides, a new capability,
KVM_CAP_HYPERV_VP_INDEX, is added to allow the userspace to skip
attempting msr writes where unsupported, to avoid spamming error logs.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Adds another flag bit (bit 2) to MSR_KVM_ASYNC_PF_EN. If bit 2 is 1,
async page faults are delivered to L1 as #PF vmexits; if bit 2 is 0,
kvm_can_do_async_pf returns 0 if in guest mode.
This is similar to what svm.c wanted to do all along, but it is only
enabled for Linux as L1 hypervisor. Foreign hypervisors must never
receive async page faults as vmexits, because they'd probably be very
confused about that.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
There is a flaw in the Hyper-V SynIC implementation in KVM: when message
page or event flags page is enabled by setting the corresponding msr,
KVM zeroes it out. This is problematic because on migration the
corresponding MSRs are loaded on the destination, so the content of
those pages is lost.
This went unnoticed so far because the only user of those pages was
in-KVM hyperv synic timers, which could continue working despite that
zeroing.
Newer QEMU uses those pages for Hyper-V VMBus implementation, and
zeroing them breaks the migration.
Besides, in newer QEMU the content of those pages is fully managed by
QEMU, so zeroing them is undesirable even when writing the MSRs from the
guest side.
To support this new scheme, introduce a new capability,
KVM_CAP_HYPERV_SYNIC2, which, when enabled, makes sure that the synic
pages aren't zeroed out in KVM.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Adds the plumbing to disable A/D bits in the MMU based on a new role
bit, ad_disabled. When A/D is disabled, the MMU operates as though A/D
aren't available (i.e., using access tracking faults instead).
To avoid SP -> kvm_mmu_page.role.ad_disabled lookups all over the
place, A/D disablement is now stored in the SPTE. This state is stored
in the SPTE by tweaking the use of SPTE_SPECIAL_MASK for access
tracking. Rather than just setting SPTE_SPECIAL_MASK when an
access-tracking SPTE is non-present, we now always set
SPTE_SPECIAL_MASK for access-tracking SPTEs.
Signed-off-by: Peter Feiner <pfeiner@google.com>
[Use role.ad_disabled even for direct (non-shadow) EPT page tables. Add
documentation and a few MMU_WARN_ONs. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts
pending.
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=6hNK
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.13
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
Conflicts:
arch/s390/include/asm/kvm_host.h
In some cases, userspace needs to get or set all ais states for example
migration. So we introduce a new group KVM_DEV_FLIC_AISM_ALL to provide
interfaces to get or set the adapter-interruption-suppression mode for
all ISCs. The corresponding documentation is updated.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
* Add the struct used in the ioctls to get and set CMMA attributes.
* Add the two functions needed to get and set the CMMA attributes for
guest pages.
* Add the two ioctls that use the aforementioned functions.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
* Add a migration state bitmap to keep track of which pages have dirty
CMMA information.
* Disable CMMA by default, so we can track if it's used or not. Enable
it on first use like we do for storage keys (unless we are doing a
migration).
* Creates a VM attribute to enter and leave migration mode.
* In migration mode, CMMA is disabled in the SIE block, so ESSA is
always interpreted and emulated in software.
* Free the migration state on VM destroy.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Now that userspace can set the virtual SMT mode by enabling the
KVM_CAP_PPC_SMT capability, it is useful for userspace to be able
to query the set of possible virtual SMT modes. This provides a
new capability, KVM_CAP_PPC_SMT_POSSIBLE, to provide this
information. The return value is a bitmap of possible modes, with
bit N set if virtual SMT mode 2^N is available. That is, 1 indicates
SMT1 is available, 2 indicates that SMT2 is available, 3 indicates
that both SMT1 and SMT2 are available, and so on.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This introduces a new KVM capability to control how KVM behaves
on machine check exception (MCE) in HV KVM guests.
If this capability has not been enabled, KVM redirects machine check
exceptions to guest's 0x200 vector, if the address in error belongs to
the guest. With this capability enabled, KVM will cause a guest exit
with the exit reason indicating an NMI.
The new capability is required to avoid problems if a new kernel/KVM
is used with an old QEMU, running a guest that doesn't issue
"ibm,nmi-register". As old QEMU does not understand the NMI exit
type, it treats it as a fatal error. However, the guest could have
handled the machine check error if the exception was delivered to
guest's 0x200 interrupt vector instead of NMI exit in case of old
QEMU.
[paulus@ozlabs.org - Reworded the commit message to be clearer,
enable only on HV KVM.]
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This allows userspace to set the desired virtual SMT (simultaneous
multithreading) mode for a VM, that is, the number of VCPUs that
get assigned to each virtual core. Previously, the virtual SMT mode
was fixed to the number of threads per subcore, and if userspace
wanted to have fewer vcpus per vcore, then it would achieve that by
using a sparse CPU numbering. This had the disadvantage that the
vcpu numbers can get quite large, particularly for SMT1 guests on
a POWER8 with 8 threads per core. With this patch, userspace can
set its desired virtual SMT mode and then use contiguous vcpu
numbering.
On POWER8, where the threading mode is "strict", the virtual SMT mode
must be less than or equal to the number of threads per subcore. On
POWER9, which implements a "loose" threading mode, the virtual SMT
mode can be any power of 2 between 1 and 8, even though there is
effectively one thread per subcore, since the threads are independent
and can all be in different partitions.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
First we define an ABI using the vcpu devices that lets userspace set
the interrupt numbers for the various timers on both the 32-bit and
64-bit KVM/ARM implementations.
Second, we add the definitions for the groups and attributes introduced
by the above ABI. (We add the PMU define on the 32-bit side as well for
symmetry and it may get used some day.)
Third, we set up the arch-specific vcpu device operation handlers to
call into the timer code for anything related to the
KVM_ARM_VCPU_TIMER_CTRL group.
Fourth, we implement support for getting and setting the timer interrupt
numbers using the above defined ABI in the arch timer code.
Fifth, we introduce error checking upon enabling the arch timer (which
is called when first running a VCPU) to check that all VCPUs are
configured to use the same PPI for the timer (as mandated by the
architecture) and that the virtual and physical timers are not
configured to use the same IRQ number.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Since we got support for devices in userspace which allows reporting the
PMU overflow output status to userspace, we should actually allow
creating the PMU on systems without an in-kernel irqchip, which in turn
requires us to slightly clarify error codes for the ABI and move things
around for the initialization phase.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZEZihAAoJEEtpOizt6ddyGDYH/jmGjDMnryORn2P2o10dUQKJ
RnHTQYnpOYqnprlkFtZFpmK+mjl/a8R1Btb7GK2EwmovTR95pMYPRqtrCTOL0aQA
4OToh7+vFGatwxsGCS6utazdhmx0UT/LhO/GEF4G1zOb7eVa4ZtS1NKLP2WjPD1E
RU3Qn8wa0pESv3tJScv8qo2+PWVX4krbFllhY2Hk0AkVQcI66ExkdVq4ikm1eUXn
rxzIayLG2bv3KEPNCzozdwoY9tDL+b40q6vN/RHGJmM05SZbbSx2/Bkw2RbslSpD
2hvhHWX7xeuEBcd5mZO7sP4WS3hM/BI8eX7q+uMeNJ9B+nM82yjGfOTtglVi2cc=
=JfvQ
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
Second round of KVM/ARM Changes for v4.12.
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
Clarify what is meant by the save/restore ABI only supporting virtual
physical interrupts.
Relax the requirement of the order that the collection entries are
written in and be clear that there is no particular ordering enforced.
Some cosmetic changes in the capitalization of ID names to align with
the GICv3 manual and remove the empty line in the bottom of the patch.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
support; virtual interrupt controller performance improvements; support
for userspace virtual interrupt controller (slower, but necessary for
KVM on the weird Broadcom SoCs used by the Raspberry Pi 3)
* MIPS: basic support for hardware virtualization (ImgTec
P5600/P6600/I6400 and Cavium Octeon III)
* PPC: in-kernel acceleration for VFIO
* s390: support for guests without storage keys; adapter interruption
suppression
* x86: usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits; emulation of CPL3 CPUID faulting
* generic: first part of VCPU thread request API; kvm_stat improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZEHUkAAoJEL/70l94x66DBeYH/09wrpJ2FjU4Rqv7FxmqgWfH
9WGi4wvn/Z+XzQSyfMJiu2SfZVzU69/Y67OMHudy7vBT6knB+ziM7Ntoiu/hUfbG
0g5KsDX79FW15HuvuuGh9kSjUsj7qsQdyPZwP4FW/6ZoDArV9mibSvdjSmiUSMV/
2wxaoLzjoShdOuCe9EABaPhKK0XCrOYkygT6Paz1pItDxaSn8iW3ulaCuWMprUfG
Niq+dFemK464E4yn6HVD88xg5j2eUM6bfuXB3qR3eTR76mHLgtwejBzZdDjLG9fk
32PNYKhJNomBxHVqtksJ9/7cSR6iNPs7neQ1XHemKWTuYqwYQMlPj1NDy0aslQU=
=IsiZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- HYP mode stub supports kexec/kdump on 32-bit
- improved PMU support
- virtual interrupt controller performance improvements
- support for userspace virtual interrupt controller (slower, but
necessary for KVM on the weird Broadcom SoCs used by the Raspberry
Pi 3)
MIPS:
- basic support for hardware virtualization (ImgTec P5600/P6600/I6400
and Cavium Octeon III)
PPC:
- in-kernel acceleration for VFIO
s390:
- support for guests without storage keys
- adapter interruption suppression
x86:
- usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits
- emulation of CPL3 CPUID faulting
generic:
- first part of VCPU thread request API
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
kvm: nVMX: Don't validate disabled secondary controls
KVM: put back #ifndef CONFIG_S390 around kvm_vcpu_kick
Revert "KVM: Support vCPU-based gfn->hva cache"
tools/kvm: fix top level makefile
KVM: x86: don't hold kvm->lock in KVM_SET_GSI_ROUTING
KVM: Documentation: remove VM mmap documentation
kvm: nVMX: Remove superfluous VMX instruction fault checks
KVM: x86: fix emulation of RSM and IRET instructions
KVM: mark requests that need synchronization
KVM: return if kvm_vcpu_wake_up() did wake up the VCPU
KVM: add explicit barrier to kvm_vcpu_kick
KVM: perform a wake_up in kvm_make_all_cpus_request
KVM: mark requests that do not need a wakeup
KVM: remove #ifndef CONFIG_S390 around kvm_vcpu_wake_up
KVM: x86: always use kvm_make_request instead of set_bit
KVM: add kvm_{test,clear}_request to replace {test,clear}_bit
s390: kvm: Cpu model support for msa6, msa7 and msa8
KVM: x86: remove irq disablement around KVM_SET_CLOCK/KVM_GET_CLOCK
kvm: better MWAIT emulation for guests
KVM: x86: virtualize cpuid faulting
...
Add description for how to save GICV3 LPI pending bit into
guest RAM pending tables.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Add description for how to access ITS registers and how to save/restore
ITS tables into/from memory.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Since commit 80f5b5e700 ("KVM: remove vm mmap method"), the VM mmap
handler is gone. Remove the corresponding documentation.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Changes include:
- Using the common sysreg definitions between KVM and arm64
- Improved hyp-stub implementation with support for kexec and kdump on the 32-bit side
- Proper PMU exception handling
- Performance improvements of our GIC handling
- Support for irqchip in userspace with in-kernel arch-timers and PMU support
- A fix for a race condition in our PSCI code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY/IasAAoJEEtpOizt6ddyd7gH/2N3BIMxi/Uqigx0e0byA43s
f+8gNq8A71VBTERGW2l9QP1/AZAXpQYNWdWmN2jn+91x2yoVL7AT00gEsliSLEZv
tqZaTGFXKi1vNihYrxEWm1mfVNzhRrnbW6vjLrO4J5Advq7T3OWhNuVt2BLTxz3Y
h0iqOWNVrUD9h3QSBFH8tz7yXhguDTSppAcXbE0tACdRu4vN50wqEWokHJG5TsMG
Tl3KYWrcc3YCKlAJGuJi7t5rMrXk+g1q6HnxlIN6OSk0POC2Vmw9/Gigtltj1Qwh
ZEAwsnka/U8ak8WaWeZa3EsGTSFSoAk/+pKv2FB8mFN+uOmWDqVlEiol4dW49AY=
=mEOk
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.12.
Changes include:
- Using the common sysreg definitions between KVM and arm64
- Improved hyp-stub implementation with support for kexec and kdump on the 32-bit side
- Proper PMU exception handling
- Performance improvements of our GIC handling
- Support for irqchip in userspace with in-kernel arch-timers and PMU support
- A fix for a race condition in our PSCI code
Conflicts:
Documentation/virtual/kvm/api.txt
include/uapi/linux/kvm.h
- Detect all function codes for KMA and export the features
for use in the cpu model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=elz2
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: MSA8 feature for guests
- Detect all function codes for KMA and export the features
for use in the cpu model
msa6 and msa7 require no changes.
msa8 adds kma instruction and feature area.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Guests that are heavy on futexes end up IPI'ing each other a lot. That
can lead to significant slowdowns and latency increase for those guests
when running within KVM.
If only a single guest is needed on a host, we have a lot of spare host
CPU time we can throw at the problem. Modern CPUs implement a feature
called "MWAIT" which allows guests to wake up sleeping remote CPUs without
an IPI - thus without an exit - at the expense of never going out of guest
context.
The decision whether this is something sensible to use should be up to the
VM admin, so to user space. We can however allow MWAIT execution on systems
that support it properly hardware wise.
This patch adds a CAP to user space and a KVM cpuid leaf to indicate
availability of native MWAIT execution. With that enabled, the worst a
guest can do is waste as many cycles as a "jmp ." would do, so it's not
a privilege problem.
We consciously do *not* expose the feature in our CPUID bitmap, as most
people will want to benefit from sleeping vCPUs to allow for over commit.
Reported-by: "Gabriel L. Somlo" <gsomlo@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[agraf: fix amd, change commit message]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows the host kernel to handle H_PUT_TCE, H_PUT_TCE_INDIRECT
and H_STUFF_TCE requests targeted an IOMMU TCE table used for VFIO
without passing them to user space which saves time on switching
to user space and back.
This adds H_PUT_TCE/H_PUT_TCE_INDIRECT/H_STUFF_TCE handlers to KVM.
KVM tries to handle a TCE request in the real mode, if failed
it passes the request to the virtual mode to complete the operation.
If it a virtual mode handler fails, the request is passed to
the user space; this is not expected to happen though.
To avoid dealing with page use counters (which is tricky in real mode),
this only accelerates SPAPR TCE IOMMU v2 clients which are required
to pre-register the userspace memory. The very first TCE request will
be handled in the VFIO SPAPR TCE driver anyway as the userspace view
of the TCE table (iommu_table::it_userspace) is not allocated till
the very first mapping happens and we cannot call vmalloc in real mode.
If we fail to update a hardware IOMMU table unexpected reason, we just
clear it and move on as there is nothing really we can do about it -
for example, if we hot plug a VFIO device to a guest, existing TCE tables
will be mirrored automatically to the hardware and there is no interface
to report to the guest about possible failures.
This adds new attribute - KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE - to
the VFIO KVM device. It takes a VFIO group fd and SPAPR TCE table fd
and associates a physical IOMMU table with the SPAPR TCE table (which
is a guest view of the hardware IOMMU table). The iommu_table object
is cached and referenced so we do not have to look up for it in real mode.
This does not implement the UNSET counterpart as there is no use for it -
once the acceleration is enabled, the existing userspace won't
disable it unless a VFIO container is destroyed; this adds necessary
cleanup to the KVM_DEV_VFIO_GROUP_DEL handler.
This advertises the new KVM_CAP_SPAPR_TCE_VFIO capability to the user
space.
This adds real mode version of WARN_ON_ONCE() as the generic version
causes problems with rcu_sched. Since we testing what vmalloc_to_phys()
returns in the code, this also adds a check for already existing
vmalloc_to_phys() call in kvmppc_rm_h_put_tce_indirect().
This finally makes use of vfio_external_user_iommu_id() which was
introduced quite some time ago and was considered for removal.
Tests show that this patch increases transmission speed from 220MB/s
to 750..1020MB/s on 10Gb network (Chelsea CXGB3 10Gb ethernet card).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
1. guarded storage support for guests
This contains an s390 base Linux feature branch that is necessary
to implement the KVM part
2. Provide an interface to implement adapter interruption suppression
which is necessary for proper zPCI support
3. Use more defines instead of numbers
4. Provide logging for lazy enablement of runtime instrumentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=Jtjb
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux
From: Christian Borntraeger <borntraeger@de.ibm.com>
KVM: s390: features for 4.12
1. guarded storage support for guests
This contains an s390 base Linux feature branch that is necessary
to implement the KVM part
2. Provide an interface to implement adapter interruption suppression
which is necessary for proper zPCI support
3. Use more defines instead of numbers
4. Provide logging for lazy enablement of runtime instrumentation
We have 2 modes for dealing with interrupts in the ARM world. We can
either handle them all using hardware acceleration through the vgic or
we can emulate a gic in user space and only drive CPU IRQ pins from
there.
Unfortunately, when driving IRQs from user space, we never tell user
space about events from devices emulated inside the kernel, which may
result in interrupt line state changes, so we lose out on for example
timer and PMU events if we run with user space gic emulation.
Define an ABI to publish such device output levels to userspace.
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to help people understanding the hyp-stub API that exists
between the host kernel and the hypervisor mode (whether a hypervisor
has been installed or not), let's document said API.
As with any form of documentation, I expect it to become obsolete
and completely misleading within 20 minutes after having being merged.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Legacy device assignment has been deprecated since 4.2 (released
1.5 years ago). VFIO is better and everyone should have switched to it.
If they haven't, this should convince them. :)
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a cap to enable AIS facility bit, and add documentation
for this capability.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add basic support for the MIPS Virtualization Module (generally known as
MIPS VZ) in KVM. We primarily support the ImgTec P5600, P6600, I6400,
and Cavium Octeon III cores so far. Support is included for the
following VZ / guest hardware features:
- MIPS32 and MIPS64, r5 (VZ requires r5 or later) and r6
- TLBs with GuestID (IMG cores) or Root ASID Dealias (Octeon III)
- Shared physical root/guest TLB (IMG cores)
- FPU / MSA
- Cop0 timer (up to 1GHz for now due to soft timer limit)
- Segmentation control (EVA)
- Hardware page table walker (HTW) both for root and guest TLB
Also included is a proper implementation of the TLBR instruction for the
trap & emulate MIPS KVM implementation.
Preliminary MIPS architecture changes are applied directly with Ralf's
ack.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJY5XPkAAoJEGwLaZPeOHZ6aLcQAI43z58kkUopHJVfXtUbS+p0
Bno+oi6XKwEL0AD361A6jflbfxaSHQocilhCBvGKf7c7Rm/oRWrAxrXDnNEDi59s
U7tH8KATdzgySu8mZOJNp8a0VcWS08yAbwOeZcqASPowBARPhlga3DCQdC6mWePi
rlfHzRi2hBNKOc1q3KmGKDfiwi4x3dcLQYd9O8RmdpAjW5bfem0mJ76w9LRkPZHz
YiCxnHYa0n4sNscT7HREe+P9/MzD2MQY04m+jhSMo/IHYPec9ap8kFN+de/4P1cT
J2yTscywsQlC56E/pcRT5X0TYAZz/rsDhmRnIKRYuJBrGIXV8BKdYyqmBrxC7o6/
K4HvXJtMzkyG/xGj5l4TqTgTlPH0k4iu/bBWvyRjd40v3ZpSq5GqNG+6VX1QfYDW
ZNa0fviC9uHqbfHijHs9IV1Kdb4bII/xd2eotCUy8jKbikd6FJWUT/XqQB4NGQpW
PZtgPXVs958vWLG1qrdh2dSMpGR21uPwp9NsqGim/3raQOlDeTUK+x384urqLcU/
pQT2WROmXw8H9qPPKpkCs9xdhp0ja2TotTJcqH+mNk+r3QzWa4N95rpd9MZKtbyc
YaQqC5FWru79ZfO53n2PsZidWyHHUS1rxYuYkopeGC7pgmoUdKdHwkzkvFdWLXHE
Ol8lksYDC5aHiWD6V8Sh
=smiL
-----END PGP SIGNATURE-----
Merge tag 'kvm_mips_4.12_1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/kvm-mips
From: James Hogan <james.hogan@imgtec.com>
KVM: MIPS: VZ support, Octeon III, and TLBR
Add basic support for the MIPS Virtualization Module (generally known as
MIPS VZ) in KVM. We primarily support the ImgTec P5600, P6600, I6400,
and Cavium Octeon III cores so far. Support is included for the
following VZ / guest hardware features:
- MIPS32 and MIPS64, r5 (VZ requires r5 or later) and r6
- TLBs with GuestID (IMG cores) or Root ASID Dealias (Octeon III)
- Shared physical root/guest TLB (IMG cores)
- FPU / MSA
- Cop0 timer (up to 1GHz for now due to soft timer limit)
- Segmentation control (EVA)
- Hardware page table walker (HTW) both for root and guest TLB
Also included is a proper implementation of the TLBR instruction for the
trap & emulate MIPS KVM implementation.
Preliminary MIPS architecture changes are applied directly with Ralf's
ack.
Inject adapter interrupts on a specified adapter which allows to
retrieve the adapter flags, e.g. if the adapter is subject to AIS
facility or not. And add documentation for this interface.
For adapters subject to AIS, handle the airq injection suppression
for a given ISC according to the interruption mode:
- before injection, if NO-Interruptions Mode, just return 0 and
suppress, otherwise, allow the injection.
- after injection, if SINGLE-Interruption Mode, change it to
NO-Interruptions Mode to suppress the following interrupts.
Besides, add tracepoint for suppressed airq and AIS mode transitions.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Provide an interface for userspace to modify AIS
(adapter-interruption-suppression) mode state, and add documentation
for the interface. Allowed target modes are ALL-Interruptions mode
and SINGLE-Interruption mode.
We introduce the 'simm' and 'nimm' fields in kvm_s390_float_interrupt
to store interruption modes for each ISC. Each bit in 'simm' and
'nimm' targets to one ISC, and collaboratively indicate three modes:
ALL-Interruptions, SINGLE-Interruption and NO-Interruptions. This
interface can initiate most transitions between the states; transition
from SINGLE-Interruption to NO-Interruptions via adapter interrupt
injection will be introduced in a following patch. The meaningful
combinations are as follows:
interruption mode | simm bit | nimm bit
------------------|----------|----------
ALL | 0 | 0
SINGLE | 1 | 0
NO | 1 | 1
Besides, add tracepoint to track AIS mode transitions.
Co-Authored-By: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In order to properly implement adapter-interruption suppression, we
need a way for userspace to specify which adapters are subject to
suppression. Let's convert the existing (and unused) 'pad' field into
a 'flags' field and define a flag value for suppressible adapters.
Besides, add documentation for the interface.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes include:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY5MItAAoJEEtpOizt6ddy4mUH/1Z2rt2mUAYFQpWD/vy9WMxf
zJKMtcLlZZGjeU78zFfWuOxEo1bbDO+tOTV1docNnY8xjyszCZ5XKOqMeo2a7Vfh
1QYHxJTOmgxcRmMsOnJpqUXhhYm9hDxrbU88U/wvoNllLjWBea01ZXiJbWFPBssT
jrdtcCVstDGp3x3D91RgYNNzj9jNw80RBekACZZwYokDRpBZyUb8DYKfUgABFEKT
UPiHrxb8UOVqvbCuXMBNzhUZcuMoAh3oY02R9sV7u1QOXAJYfRV4fOV12fIcYbHf
tnyU8cCxEkSI1pHrpVG6SStcMt8yznQ+UPo0okQNBJXim2yI8+QKHtQlvx7Tjo8=
=tPDd
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
From: Christoffer Dall <cdall@linaro.org>
KVM/ARM Fixes for v4.11-rc6
Fixes include:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
As an oversight, for GICv2, we accidentally export the GICC_PMR register
in the format of the GICH_VMCR.VMPriMask field in the lower 5 bits of a
word, meaning that userspace must always use the lower 5 bits to
communicate with the KVM device and must shift the value left by 3
places to obtain the actual priority mask level.
Since GICv3 supports the full 8 bits of priority masking in the ICH_VMCR,
we have to fix the value we export when emulating a GICv2 on top of a
hardware GICv3 and exporting the emulated GICv2 state to userspace.
Take the chance to clarify this aspect of the ABI.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add emulation of Memory Accessibility Attribute Registers (MAARs) when
necessary. We can't actually do anything with whatever the guest
provides, but it may not be possible to clear Guest.Config5.MRP so we
have to emulate at least a pair of MAARs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add support for VZ guest CP0_PWBase, CP0_PWField, CP0_PWSize, and
CP0_PWCtl registers for controlling the guest hardware page table walker
(HTW) present on P5600 and P6600 cores. These guest registers need
initialising on R6, context switching, and exposing via the KVM ioctl
API when they are present.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add support for VZ guest CP0_SegCtl0, CP0_SegCtl1, and CP0_SegCtl2
registers, as found on P5600 and P6600 cores. These guest registers need
initialising, context switching, and exposing via the KVM ioctl API when
they are present.
They also require the GVA -> GPA translation code for handling a GVA
root exception to be updated to interpret the segmentation registers and
decode the faulting instruction enough to detect EVA memory access
instructions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add support for VZ guest CP0_ContextConfig and CP0_XContextConfig
(MIPS64 only) registers, as found on P5600 and P6600 cores. These guest
registers need initialising, context switching, and exposing via the KVM
ioctl API when they are present.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add support for VZ guest CP0_BadInstr and CP0_BadInstrP registers, as
found on most VZ capable cores. These guest registers need context
switching, and exposing via the KVM ioctl API when they are present.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add the main support for the MIPS Virtualization ASE (A.K.A. VZ) to MIPS
KVM. The bulk of this work is in vz.c, with various new state and
definitions elsewhere.
Enough is implemented to be able to run on a minimal VZ core. Further
patches will fill out support for guest features which are optional or
can be disabled.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add a new KVM_CAP_MIPS_64BIT capability to indicate that 64-bit MIPS
guests are available and supported. In this case it should still be
possible to run 32-bit guest code. If not available it won't be possible
to run 64-bit guest code and the instructions may not be available, or
the kernel may not support full context switching of 64-bit registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add new KVM_CAP_MIPS_VZ and KVM_CAP_MIPS_TE capabilities, and in order
to allow MIPS KVM to support VZ without confusing old users (which
expect the trap & emulate implementation), define and start checking
KVM_CREATE_VM type codes.
The codes available are:
- KVM_VM_MIPS_TE = 0
This is the current value expected from the user, and will create a
VM using trap & emulate in user mode, confined to the user mode
address space. This may in future become unavailable if the kernel is
only configured to support VZ, in which case the EINVAL error will be
returned and KVM_CAP_MIPS_TE won't be available even though
KVM_CAP_MIPS_VZ is.
- KVM_VM_MIPS_VZ = 1
This can be provided when the KVM_CAP_MIPS_VZ capability is available
to create a VM using VZ, with a fully virtualized guest virtual
address space. If VZ support is unavailable in the kernel, the EINVAL
error will be returned (although old kernels without the
KVM_CAP_MIPS_VZ capability may well succeed and create a trap &
emulate VM).
This is designed to allow the desired implementation (T&E vs VZ) to be
potentially chosen at runtime rather than being fixed in the kernel
configuration.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Emulate the HYPCALL instruction added in the VZ ASE and used by the MIPS
paravirtualised guest support that is already merged. The new hypcall.c
handles arguments and the return value. No actual hypercalls are yet
supported, but this still allows us to safely step over hypercalls and
set an error code in the return value for forward compatibility.
Non-zero HYPCALL codes are not handled.
We also document the hypercall ABI which asm/kvm_para.h uses.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
This patch adds guarded storage support for KVM guest. We need to
setup the necessary control blocks, the kvm_run structure for the
new registers, the necessary wrappers for VSIE, as well as the
machine check save areas.
GS is enabled lazily and the register saving and reloading is done in
KVM code. As this feature adds new content for migration, we provide
a new capability for enablement (KVM_CAP_S390_GS).
Signed-off-by: Fan Zhang <zhangfan@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The purpose of the KVM_SET_SIGNAL_MASK API is to let userspace "kick"
a VCPU out of KVM_RUN through a POSIX signal. A signal is attached
to a dummy signal handler; by blocking the signal outside KVM_RUN and
unblocking it inside, this possible race is closed:
VCPU thread service thread
--------------------------------------------------------------
check flag
set flag
raise signal
(signal handler does nothing)
KVM_RUN
However, one issue with KVM_SET_SIGNAL_MASK is that it has to take
tsk->sighand->siglock on every KVM_RUN. This lock is often on a
remote NUMA node, because it is on the node of a thread's creator.
Taking this lock can be very expensive if there are many userspace
exits (as is the case for SMP Windows VMs without Hyper-V reference
time counter).
As an alternative, we can put the flag directly in kvm_run so that
KVM can see it:
VCPU thread service thread
--------------------------------------------------------------
raise signal
signal handler
set run->immediate_exit
KVM_RUN
check run->immediate_exit
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Numerous MIPS KVM fixes, improvements, and features for 4.11, many of
which continue to pave the way for VZ support, the most interesting of
which are:
- Add GVA->HPA page tables for T&E, to cache GVA mappings.
- Generate fast-path TLB refill exception handler which loads host TLB
entries from GVA page table, avoiding repeated guest memory
translation and guest TLB lookups.
- Use uaccess macros when T&E needs to access guest memory, which with
GVA page tables and the Linux TLB refill handler improves robustness
against TLB faults and fixes EVA hosts.
- Use BadInstr/BadInstrP registers when available to obtain instruction
encodings after a synchronous trap.
- Add GPA->HPA page tables to replace the inflexible linear array,
allowing for multiple sparsely arranged memory regions.
- Properly implement dirty page logging.
- Add KVM_CAP_SYNC_MMU support so that changes in GPA mappings become
effective in guests even if they are already running, allowing for
copy-on-write, KSM, idle page tracking, swapping, and guest memory
ballooning.
- Add KVM_CAP_READONLY_MEM support, so writes to specified memory
regions are treated as MMIO.
- Implement proper CP0_EBase support in T&E.
- Expose a few more missing CP0 registers to userland.
- Add KVM_CAP_NR_VCPUS and KVM_CAP_MAX_VCPUS support, and allow up to 8
VCPUs to be created in a VM.
- Various cleanups and dropping of dead and duplicated code.
-----BEGIN PGP SIGNATURE-----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=lMjW
-----END PGP SIGNATURE-----
Merge tag 'kvm_mips_4.11_1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/kvm-mips into HEAD
KVM: MIPS: GVA/GPA page tables, dirty logging, SYNC_MMU etc
Numerous MIPS KVM fixes, improvements, and features for 4.11, many of
which continue to pave the way for VZ support, the most interesting of
which are:
- Add GVA->HPA page tables for T&E, to cache GVA mappings.
- Generate fast-path TLB refill exception handler which loads host TLB
entries from GVA page table, avoiding repeated guest memory
translation and guest TLB lookups.
- Use uaccess macros when T&E needs to access guest memory, which with
GVA page tables and the Linux TLB refill handler improves robustness
against TLB faults and fixes EVA hosts.
- Use BadInstr/BadInstrP registers when available to obtain instruction
encodings after a synchronous trap.
- Add GPA->HPA page tables to replace the inflexible linear array,
allowing for multiple sparsely arranged memory regions.
- Properly implement dirty page logging.
- Add KVM_CAP_SYNC_MMU support so that changes in GPA mappings become
effective in guests even if they are already running, allowing for
copy-on-write, KSM, idle page tracking, swapping, and guest memory
ballooning.
- Add KVM_CAP_READONLY_MEM support, so writes to specified memory
regions are treated as MMIO.
- Implement proper CP0_EBase support in T&E.
- Expose a few more missing CP0 registers to userland.
- Add KVM_CAP_NR_VCPUS and KVM_CAP_MAX_VCPUS support, and allow up to 8
VCPUs to be created in a VM.
- Various cleanups and dropping of dead and duplicated code.
The big feature this time is support for POWER9 using the radix-tree
MMU for host and guest. This required some changes to arch/powerpc
code, so I talked with Michael Ellerman and he created a topic branch
with this patchset, which I merged into kvm-ppc-next and which Michael
will pull into his tree. Michael also put in some patches from Nick
Piggin which fix bugs in the interrupt vector code in relocatable
kernels when coming from a KVM guest.
Other notable changes include:
* Add the ability to change the size of the hashed page table,
from David Gibson.
* XICS (interrupt controller) emulation fixes and improvements,
from Li Zhong.
* Bug fixes from myself and Thomas Huth.
These patches define some new KVM capabilities and ioctls, but there
should be no conflicts with anything else currently upstream, as far
as I am aware.
Add a hypercall to retrieve the host realtime clock and the TSC value
used to calculate that clock read.
Used to implement clock synchronization between host and guest.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the CP0_IntCtl register through the KVM register access API,
which is a required register since MIPS32r2. It is currently read-only
since the VS field isn't implemented due to lack of Config3.VInt or
Config3.VEIC.
It is implemented in trap_emul.c so that a VZ implementation can allow
writes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Expose the CP0_EntryLo0 and CP0_EntryLo1 registers through the KVM
register access API. This is fairly straightforward for trap & emulate
since we don't support the RI and XI bits. For the sake of future
proofing (particularly for VZ) it is explicitly specified that the API
always exposes the 64-bit version of these registers (i.e. with the RI
and XI bits in bit positions 63 and 62 respectively), and they are
implemented in trap_emul.c rather than mips.c to allow them to be
implemented differently for VZ.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
The CP0_EBase register is a standard feature of MIPS32r2, so we should
always have been implementing it properly. However the register value
was ignored and wasn't exposed to userland.
Fix the emulation of exceptions and interrupts to use the value stored
in guest CP0_EBase, and fix the masks so that the top 3 bits (rather
than the standard 2) are fixed, so that it is always in the guest KSeg0
segment.
Also add CP0_EBASE to the KVM one_reg interface so it can be accessed by
userland, also allowing the CPU number field to be written (which isn't
permitted by the guest).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
The KVM_PPC_ALLOCATE_HTAB ioctl() is used to set the size of hashed page
table (HPT) that userspace expects a guest VM to have, and is also used to
clear that HPT when necessary (e.g. guest reboot).
At present, once the ioctl() is called for the first time, the HPT size can
never be changed thereafter - it will be cleared but always sized as from
the first call.
With upcoming HPT resize implementation, we're going to need to allow
userspace to resize the HPT at reset (to change it back to the default size
if the guest changed it).
So, we need to allow this ioctl() to change the HPT size.
This patch also updates Documentation/virtual/kvm/api.txt to reflect
the new behaviour. In fact the documentation was already slightly
incorrect since 572abd5 "KVM: PPC: Book3S HV: Don't fall back to
smaller HPT size in allocation ioctl"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a new powerpc-specific KVM_CAP_SPAPR_RESIZE_HPT capability to
advertise whether KVM is capable of handling the PAPR extensions for
resizing the hashed page table during guest runtime. It also adds
definitions for two new VM ioctl()s to implement this extension, and
documentation of the same.
Note that, HPT resizing is already possible with KVM PR without kernel
modification, since the HPT is managed within userspace (qemu). The
capability defined here will only be set where an in-kernel implementation
of resizing is necessary, i.e. for KVM HV. To determine if the userspace
resize implementation can be used, it's necessary to check
KVM_CAP_PPC_ALLOC_HTAB. Unfortunately older kernels incorrectly set
KVM_CAP_PPC_ALLOC_HTAB even with KVM PR. If userspace it want to support
resizing with KVM PR on such kernels, it will need a workaround.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Both KVM_CREATE_SPAPR_TCE_64 and KVM_REINJECT_CONTROL have section number
4.98 in Documentation/virtual/kvm/api.txt, presumably due to a naive merge.
This corrects the duplication.
[paulus@ozlabs.org - correct section numbers for following sections,
KVM_PPC_CONFIGURE_V3_MMU and KVM_PPC_GET_RMMU_INFO, as well.]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the POWER9 radix MMU host and guest support, which
was put into a topic branch because it touches both powerpc and
KVM code.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds two capabilities and two ioctls to allow userspace to
find out about and configure the POWER9 MMU in a guest. The two
capabilities tell userspace whether KVM can support a guest using
the radix MMU, or using the hashed page table (HPT) MMU with a
process table and segment tables. (Note that the MMUs in the
POWER9 processor cores do not use the process and segment tables
when in HPT mode, but the nest MMU does).
The KVM_PPC_CONFIGURE_V3_MMU ioctl allows userspace to specify
whether a guest will use the radix MMU or the HPT MMU, and to
specify the size and location (in guest space) of the process
table.
The KVM_PPC_GET_RMMU_INFO ioctl gives userspace information about
the radix MMU. It returns a list of supported radix tree geometries
(base page size and number of bits indexed at each level of the
radix tree) and the encoding used to specify the various page
sizes for the TLB invalidate entry instruction.
Initially, both capabilities return 0 and the ioctls return -EINVAL,
until the necessary infrastructure for them to operate correctly
is added.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update error code returned for Invalid CPU interface register
value and access in AArch32 mode.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a brief description of the lockless access tracking mechanism
to the documentation of fast page faults in locking.txt.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a new mutex to avoid an AB-BA deadlock between kvm->lock and
vcpu->mutex. Protect accesses in kvm_hv_setup_tsc_page too, as suggested
by Roman.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86: userspace can now hide nested VMX features from guests; nested
VMX can now run Hyper-V in a guest; support for AVX512_4VNNIW and
AVX512_FMAPS in KVM; infrastructure support for virtual Intel GPUs.
PPC: support for KVM guests on POWER9; improved support for interrupt
polling; optimizations and cleanups.
s390: two small optimizations, more stuff is in flight and will be
in 4.11.
ARM: support for the GICv3 ITS on 32bit platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYTkP0FBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
lZIH/iT1n9OQXcuTpYYnQhuCenzI3GZZOIMTbCvK2i5bo0FIJKxVn0EiAAqZSXvO
nO185FqjOgLuJ1AD1kJuxzye5suuQp4HIPWWgNHcexLuy43WXWKZe0IQlJ4zM2Xf
u31HakpFmVDD+Cd1qN3yDXtDrRQ79/xQn2kw7CWb8olp+pVqwbceN3IVie9QYU+3
gCz0qU6As0aQIwq2PyalOe03sO10PZlm4XhsoXgWPG7P18BMRhNLTDqhLhu7A/ry
qElVMANT7LSNLzlwNdpzdK8rVuKxETwjlc1UP8vSuhrwad4zM2JJ1Exk26nC2NaG
D0j4tRSyGFIdx6lukZm7HmiSHZ0=
=mkoB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.
x86:
- userspace can now hide nested VMX features from guests
- nested VMX can now run Hyper-V in a guest
- support for AVX512_4VNNIW and AVX512_FMAPS in KVM
- infrastructure support for virtual Intel GPUs.
PPC:
- support for KVM guests on POWER9
- improved support for interrupt polling
- optimizations and cleanups.
s390:
- two small optimizations, more stuff is in flight and will be in
4.11.
ARM:
- support for the GICv3 ITS on 32bit platforms"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
arm64: KVM: pmu: Reset PMSELR_EL0.SEL to a sane value before entering the guest
KVM: arm/arm64: timer: Check for properly initialized timer on init
KVM: arm/arm64: vgic-v2: Limit ITARGETSR bits to number of VCPUs
KVM: x86: Handle the kthread worker using the new API
KVM: nVMX: invvpid handling improvements
KVM: nVMX: check host CR3 on vmentry and vmexit
KVM: nVMX: introduce nested_vmx_load_cr3 and call it on vmentry
KVM: nVMX: propagate errors from prepare_vmcs02
KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT
KVM: nVMX: load GUEST_EFER after GUEST_CR0 during emulated VM-entry
KVM: nVMX: generate MSR_IA32_CR{0,4}_FIXED1 from guest CPUID
KVM: nVMX: fix checks on CR{0,4} during virtual VMX operation
KVM: nVMX: support restore of VMX capability MSRs
KVM: nVMX: generate non-true VMX MSRs based on true versions
KVM: x86: Do not clear RFLAGS.TF when a singlestep trap occurs.
KVM: x86: Add kvm_skip_emulated_instruction and use it.
KVM: VMX: Move skip_emulated_instruction out of nested_vmx_check_vmcs12
KVM: VMX: Reorder some skip_emulated_instruction calls
KVM: x86: Add a return value to kvm_emulate_cpuid
KVM: PPC: Book3S: Move prototypes for KVM functions into kvm_ppc.h
...
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYTbl7AAoJEI3ONVYwIuV63NIP/REwzThnGWFJMRSuq8Ieq2r9
sFSQsaGTGlhyKiDoEooo+SO/Za3uTonjK+e7WZg8mhdiEdamta5aociU/71C1Yy/
T9ur0FhcGblrvZ1NidSDvCLwuECZOMMei7mgLZ9a+KCpc4ANqqTVZSUm1blKcqhF
XelhVXxBa0ar35l/pVzyCxkdNXRWXv+MJZE8hp5XAdTdr11DS7UY9zrZdH31axtf
BZlbYJrvB8WPydU6myTjRpirA17Hu7uU64MsL3bNIEiRQ+nVghEzQC8uxeUCvfVx
r0H5AgGGQeir+e8GEv2T20SPZ+dumXs+y/HehKNb3jS3gV0mo+pKPeUhwLIxr+Zh
QY64gf+jYf5ISHwAJRnU0Ima72ehObzSbx9Dko10nhq2OvbR5f83gjz9t9jKYFU7
RDowICA8lwqyRbHRoVfyoW8CpVhWFpMFu3yNeJMckeTish3m7ANqzaWslbsqIP5G
zxgFMIrVVSbeae+sUeygtEJAnWI09aZ4tuaUXYtGWwu6ikC/3aV6DryP4bthG2LF
A19uV4nMrLuuh8g2wiTHHjMfjYRwvSn+f9yaolwJhwyNDXQzRPy+ZJ3W/6olOkXC
bAxTmVRCW5GA/fmSrfXmW1KbnxlWfP2C62hzZQ09UHxzTHdR97oFLDQdZhKo1uwf
pmSJR0hVeRUmA4uw6+Su
=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
- Support for the GICv3 ITS on 32bit platforms
- A handful of timer and GIC emulation fixes
- A PMU architecture fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zxXl
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.10:
- Support for the GICv3 ITS on 32bit platforms
- A handful of timer and GIC emulation fixes
- A PMU architecture fix
There is currently no documentation about the halt polling capabilities
of the kvm module. Add some documentation describing the mechanism as well
as the module parameters to all better understanding of how halt polling
should be used and the effect of tuning the module parameters.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register). They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.
The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode. We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state. Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.
This fixes it by saving and restoring the XER. To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.
The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.
Fixes: e4e3812150 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccefcb ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Userspace can read the exact value of kvmclock by reading the TSC
and fetching the timekeeping parameters out of guest memory. This
however is brittle and not necessary anymore with KVM 4.11. Provide
a mechanism that lets userspace know if the new KVM_GET_CLOCK
semantics are in effect, and---since we are at it---if the clock
is stable across all VCPUs.
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc4' into sound
Bring in -rc4 patches so I can successfully merge the sound doc changes.
This patch allows to build and use vGICv3 ITS in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is long overdue, and not really hard.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1476357057-17899-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If userspace creates a PMU for the VCPU, but doesn't create an in-kernel
irqchip, then we end up in a nasty path where we try to take an
uninitialized spinlock, which can lead to all sorts of breakages.
Luckily, QEMU always creates the VGIC before the PMU, so we can
establish this as ABI and check for the VGIC in the PMU init stage.
This can be relaxed at a later time if we want to support PMU with a
userspace irqchip.
Cc: stable@vger.kernel.org
Cc: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Factor out the GICv3 and ITS-specific documentation into a separate
documentation file. Add description for how to access distributor,
redistributor, and CPU interface registers for GICv3 in this new file,
and add a group for accessing level triggered IRQ information for GICv3
as well.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The KVM_X2APIC_API_USE_32BIT_IDS feature applies to both
KVM_SET_GSI_ROUTING and KVM_SIGNAL_MSI, but was not mentioned in the
documentation for the latter ioctl.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXoydqAAoJEEtpOizt6ddyM3oH/1A4VeG/J9q4fBPXqY2tVWXs
c3P7UgNcrEgUNs/F9ykQY/lb31deecUzaBt1OyTf+RlsNbihq3dQdYcBhxtUODw/
Faok582ya3UFgLW+IRHcID0EbkVOpIzMhOStYsnU/Dz7HG1JL9HdPzwkid7iu9LT
fI6yrrBnJFjdWAAQ4BkcEKBENRsY8NTs7jX5vnFA92MkUBby7BmariPDD3FtrB+f
Ob9B7CxM30pNqsN7OA/QvFOHMJHxf3s1TBKwmPHe5TLIfSzV1YxcEGiMc0lWqF4v
BT8ZeMGCtjDw94tND1DskfQQRPaMqPmGuRTrAW/IuE2n92bFtbqIqs7Cbw0fzLE=
=Vm6Q
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.8-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.8 - Take 2
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
- GICv3 ITS emulation
- Simpler idmap management that fixes potential TLB conflicts
- Honor the kernel protection in HYP mode
- Removal of the old vgic implementation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Del
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into next
KVM/ARM changes for Linux 4.8
- GICv3 ITS emulation
- Simpler idmap management that fixes potential TLB conflicts
- Honor the kernel protection in HYP mode
- Removal of the old vgic implementation
Up to now, only irqchip routing entries could be set. This patch
adds the capability to insert MSI routing entries.
For ARM64, let's also increase KVM_MAX_IRQ_ROUTES to 4096: this
include SPI irqchip routes plus MSI routes. In the future this
might be extended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds compilation and link against irqchip.
Main motivation behind using irqchip code is to enable MSI
routing code. In the future irqchip routing may also be useful
when targeting multiple irqchips.
Routing standard callbacks now are implemented in vgic-irqfd:
- kvm_set_routing_entry
- kvm_set_irq
- kvm_set_msi
They only are supported with new_vgic code.
Both HAVE_KVM_IRQCHIP and HAVE_KVM_IRQ_ROUTING are defined.
KVM_CAP_IRQ_ROUTING is advertised and KVM_SET_GSI_ROUTING is allowed.
So from now on IRQCHIP routing is enabled and a routing table entry
must exist for irqfd injection to succeed for a given SPI. This patch
builds a default flat irqchip routing table (gsi=irqchip.pin) covering
all the VGIC SPI indexes. This routing table is overwritten by the
first first user-space call to KVM_SET_GSI_ROUTING ioctl.
MSI routing setup is not yet allowed.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On ARM, the MSI msg (address and data) comes along with
out-of-band device ID information. The device ID encodes the
device that writes the MSI msg. Let's convey the device id in
kvm_irq_routing_msi and use KVM_MSI_VALID_DEVID flag value in
kvm_irq_routing_entry to indicate the msi devid is populated.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that all ITS emulation functionality is in place, we advertise
MSI functionality to userland and also the ITS device to the guest - if
userland has configured that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce a new KVM device that represents an ARM Interrupt Translation
Service (ITS) controller. Since there can be multiple of this per guest,
we can't piggy back on the existing GICv3 distributor device, but create
a new type of KVM device.
On the KVM_CREATE_DEVICE ioctl we allocate and initialize the ITS data
structure and store the pointer in the kvm_device data.
Upon an explicit init ioctl from userland (after having setup the MMIO
address) we register the handlers with the kvm_io_bus framework.
Any reference to an ITS thus has to go via this interface.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ARM GICv3 ITS MSI controller requires a device ID to be able to
assign the proper interrupt vector. On real hardware, this ID is
sampled from the bus. To be able to emulate an ITS controller, extend
the KVM MSI interface to let userspace provide such a device ID. For
PCI devices, the device ID is simply the 16-bit bus-device-function
triplet, which should be easily available to the userland tool.
Also there is a new KVM capability which advertises whether the
current VM requires a device ID to be set along with the MSI data.
This flag is still reported as not available everywhere, later we will
enable it when ITS emulation is used.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We will use illegal instruction 0x0000 for handling 2 byte sw breakpoints
from user space. As it can be enabled dynamically via a capability,
let's move setting of ICTL_OPEREXC to the post creation step, so we avoid
any races when enabling that capability just while adding new cpus.
Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add KVM_X2APIC_API_DISABLE_BROADCAST_QUIRK as a feature flag to
KVM_CAP_X2APIC_API.
The quirk made KVM interpret 0xff as a broadcast even in x2APIC mode.
The enableable capability is needed in order to support standard x2APIC and
remain backward compatible.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Expand kvm_apic_mda comment. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_CAP_X2APIC_API is a capability for features related to x2APIC
enablement. KVM_X2APIC_API_32BIT_FORMAT feature can be enabled to
extend APIC ID in get/set ioctl and MSI addresses to 32 bits.
Both are needed to support x2APIC.
The feature has to be enableable and disabled by default, because
get/set ioctl shifted and truncated APIC ID to 8 bits by using a
non-standard protocol inspired by xAPIC and the change is not
backward-compatible.
Changes to MSI addresses follow the format used by interrupt remapping
unit. The upper address word, that used to be 0, contains upper 24 bits
of the LAPIC address in its upper 24 bits. Lower 8 bits are reserved as
0. Using the upper address word is not backward-compatible either as we
didn't check that userspace zeroed the word. Reserved bits are still
not explicitly checked, but non-zero data will affect LAPIC addresses,
which will cause a bug.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow up to 6 KVM guest KScratch registers to be enabled and accessed
via the KVM guest register API and from the guest itself (the fallback
reading and writing of commpage registers is sufficient for KScratch
registers to work as expected).
User mode can expose the registers by setting the appropriate bits of
the guest Config4.KScrExist field. KScratch registers that aren't usable
won't be writeable via the KVM Ioctl API.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Four bigger things:
1. The implementation of the STHYI opcode in the kernel. This is used
in libraries like qclib [1] to provide enough information for a
capacity and usage based software licence pricing. The STHYI content
is defined by the related z/VM documentation [2]. Its data can be
composed by accessing several other interfaces provided by LPAR or
the machine. This information is partially sensitive or root-only
so the kernel does the necessary filtering.
2. Preparation for nested virtualization (VSIE). KVM should query the
proper sclp interfaces for the availability of some features before
using it. In the past we have been sloppy and simply assumed that
several features are available. With this we should be able to handle
most cases of a missing feature.
3. CPU model interfaces extended by some additional features that are
not covered by a facility bit in STFLE. For example all the crypto
instructions of the coprocessor provide a query function. As reality
tends to be more complex (e.g. export regulations might block some
algorithms) we have to provide additional interfaces to query or
set these non-stfle features.
4. Several fixes and changes detected and fixed when doing 1-3.
All features change base s390 code. All relevant patches have an ACK
from the s390 or component maintainers.
The next pull request for 4.8 (part2) will contain the implementation
of VSIE.
[1] http://www.ibm.com/developerworks/linux/linux390/qclib.html
[2] https://www.ibm.com/support/knowledgecenter/SSB27U_6.3.0/com.ibm.zvm.v630.hcpb4/hcpb4sth.htm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iQIcBAABAgAGBQJXX+A6AAoJEBF7vIC1phx8SBoQAIkFTMxoGvY9lFkkreUXIyeX
XL0grybhsaKd4tT80FlobTl2ejpo/feRl5RfD5Oi75UCR4oMuk3Eb8bIyQjcKJvS
7sYFz+zP9TZ5S/rxvc3EanXpcNnfowKDuLUyOTaq0Hq8XQHaSwzYGGbtPgTdMDAp
DyhwNhYK8cPvmBS3KHX70ZOMfl9J4s0xvgs42BRJyyDGYrJOZcN1NLsG2l1dAb0L
au/Svb05PxhgQvqoUId3VSrmRKLm9tSk5DJdIRcmj1+4Mlhfw14LTV+wGuTLTgSZ
GOyEdum2E/b4QABWca7sxmgqo+Wo5voOW+WKOGLMiN2sK+JwvSnu4qmiRG/qgFCJ
EQDZer+OEQTu+YgZzjm/r5wbIkV/gqUenjjepk5iWrxK6EB7CmlQuZyyEKm3wO7i
LrEDqRU7SY+PuUu+Ov6/PHxmMy5DJuK+AedRe8uzuDSmYpSekYFLD44gctkPe56q
uq4Fhx3g3EIkPMcHnAae92vHLp/INCHCGoPb4Xh6CnaP4Xm+RntCv2hWxw30rHgc
IIYVy4fSyJuTeHpFcNgeBrbcx4jwvkfJ9kxezM864DA9hBBfcS3ZZDhLM5PPEaLr
usu7Gt6nHeFtwvXxZn/Y+SsYWCWpmbt6An/m+lqf05aAqyndhbwJ8Kftz3OAxKDw
b7o59x2wvV9dfakAHxNx
=fdBQ
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Features and fixes for 4.8 part1
Four bigger things:
1. The implementation of the STHYI opcode in the kernel. This is used
in libraries like qclib [1] to provide enough information for a
capacity and usage based software licence pricing. The STHYI content
is defined by the related z/VM documentation [2]. Its data can be
composed by accessing several other interfaces provided by LPAR or
the machine. This information is partially sensitive or root-only
so the kernel does the necessary filtering.
2. Preparation for nested virtualization (VSIE). KVM should query the
proper sclp interfaces for the availability of some features before
using it. In the past we have been sloppy and simply assumed that
several features are available. With this we should be able to handle
most cases of a missing feature.
3. CPU model interfaces extended by some additional features that are
not covered by a facility bit in STFLE. For example all the crypto
instructions of the coprocessor provide a query function. As reality
tends to be more complex (e.g. export regulations might block some
algorithms) we have to provide additional interfaces to query or
set these non-stfle features.
4. Several fixes and changes detected and fixed when doing 1-3.
All features change base s390 code. All relevant patches have an ACK
from the s390 or component maintainers.
The next pull request for 4.8 (part2) will contain the implementation
of VSIE.
[1] http://www.ibm.com/developerworks/linux/linux390/qclib.html
[2] https://www.ibm.com/support/knowledgecenter/SSB27U_6.3.0/com.ibm.zvm.v630.hcpb4/hcpb4sth.htm
Let's not provide the device attribute for cmma enabling and clearing
if the hardware doesn't support it.
This also helps getting rid of the undocumented return value "-EINVAL"
in case CMMA is not available when trying to enable it.
Also properly document the meaning of -EINVAL for CMMA clearing.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We have certain instructions that indicate available subfunctions via
a query subfunction (crypto functions and ptff), or via a test bit
function (plo).
By exposing these "subfunction blocks" to user space, we allow user space
to
1) query available subfunctions and make sure subfunctions won't get lost
during migration - e.g. properly indicate them via a CPU model
2) change the subfunctions to be reported to the guest (even adding
unavailable ones)
This mechanism works just like the way we indicate the stfl(e) list to
user space.
This way, user space could even emulate some subfunctions in QEMU in the
future. If this is ever applicable, we have to make sure later on, that
unsupported subfunctions result in an intercept to QEMU.
Please note that support to indicate them to the guest is still missing
and requires hardware support. Usually, the IBC takes already care of these
subfunctions for migration safety. QEMU should make sure to always set
these bits properly according to the machine generation to be emulated.
Available subfunctions are only valid in combination with STFLE bits
retrieved via KVM_S390_VM_CPU_MACHINE and enabled via
KVM_S390_VM_CPU_PROCESSOR. If the applicable bits are available, the
indicated subfunctions are guaranteed to be correct.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
For now, we only have an interface to query and configure facilities
indicated via STFL(E). However, we also have features indicated via
SCLP, that have to be indicated to the guest by user space and usually
require KVM support.
This patch allows user space to query and configure available cpu features
for the guest.
Please note that disabling a feature doesn't necessarily mean that it is
completely disabled (e.g. ESOP is mostly handled by the SIE). We will try
our best to disable it.
Most features (e.g. SCLP) can't directly be forwarded, as most of them need
in addition to hardware support, support in KVM. As we later on want to
turn these features in KVM explicitly on/off (to simulate different
behavior), we have to filter all features provided by the hardware and
make them configurable.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The KVM_MAX_VCPUS define provides the maximum number of vCPUs per guest, and
also the upper limit for vCPU ids. This is okay for all archs except PowerPC
which can have higher ids, depending on the cpu/core/thread topology. In the
worst case (single threaded guest, host with 8 threads per core), it limits
the maximum number of vCPUS to KVM_MAX_VCPUS / 8.
This patch separates the vCPU numbering from the total number of vCPUs, with
the introduction of KVM_MAX_VCPU_ID, as the maximal valid value for vCPU ids
plus one.
The corresponding KVM_CAP_MAX_VCPU_ID allows userspace to validate vCPU ids
before passing them to KVM_CREATE_VCPU.
This patch only implements KVM_MAX_VCPU_ID with a specific value for PowerPC.
Other archs continue to return KVM_MAX_VCPUS instead.
Suggested-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Use hardware provided information about facility bits that do not
need any hypervisor activitiy
- Add missing documentation for KVM_CAP_S390_RI
- Some updates/fixes for handling cpu models and facilities
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=eTE9
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: features and fixes for 4.7 part2
- Use hardware provided information about facility bits that do not
need any hypervisor activitiy
- Add missing documentation for KVM_CAP_S390_RI
- Some updates/fixes for handling cpu models and facilities
We forgot to document that capability, let's add documentation.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Introduce a FLIC operation for clearing I/O interrupts for a subchannel.
Rationale: According to the platform specification, pending I/O
interruption requests have to be revoked in certain situations. For
instance, according to the Principles of Operation (page 17-27), a
subchannel put into the installed parameters initialized state is in the
same state as after an I/O system reset (just parameters possibly changed).
This implies that any I/O interrupts for that subchannel are no longer
pending (as I/O system resets clear I/O interrupts). Therefore, we need an
interface to clear pending I/O interrupts.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
FLIC behavior deviates from the API documentation in reporting EINVAL
instead of ENXIO for KVM_SET_DEVICE_ATTR/KVM_GET_DEVICE_ATTR when the group
or attribute is unknown/unsupported. Unfortunately this can not be fixed
for historical reasons. Let us at least have it documented.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
but lots of architecture-specific changes.
* ARM:
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- various optimizations to the vgic save/restore code.
* PPC:
- enabled KVM-VFIO integration ("VFIO device")
- optimizations to speed up IPIs between vcpus
- in-kernel handling of IOMMU hypercalls
- support for dynamic DMA windows (DDW).
* s390:
- provide the floating point registers via sync regs;
- separated instruction vs. data accesses
- dirty log improvements for huge guests
- bugfixes and documentation improvements.
* x86:
- Hyper-V VMBus hypercall userspace exit
- alternative implementation of lowest-priority interrupts using vector
hashing (for better VT-d posted interrupt support)
- fixed guest debugging with nested virtualizations
- improved interrupt tracking in the in-kernel IOAPIC
- generic infrastructure for tracking writes to guest memory---currently
its only use is to speedup the legacy shadow paging (pre-EPT) case, but
in the future it will be used for virtual GPUs as well
- much cleanup (LAPIC, kvmclock, MMU, PIT), including ubsan fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJW5r3BAAoJEL/70l94x66D2pMH/jTSWWwdTUJMctrDjPVzKzG0
yOzHW5vSLFoFlwEOY2VpslnXzn5TUVmCAfrdmFNmQcSw6hGb3K/xA/ZX/KLwWhyb
oZpr123ycahga+3q/ht/dFUBCCyWeIVMdsLSFwpobEBzPL0pMgc9joLgdUC6UpWX
tmN0LoCAeS7spC4TTiTTpw3gZ/L+aB0B6CXhOMjldb9q/2CsgaGyoVvKA199nk9o
Ngu7ImDt7l/x1VJX4/6E/17VHuwqAdUrrnbqerB/2oJ5ixsZsHMGzxQ3sHCmvyJx
WG5L00ubB1oAJAs9fBg58Y/MdiWX99XqFhdEfxq4foZEiQuCyxygVvq3JwZTxII=
=OUZZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One of the largest releases for KVM... Hardly any generic
changes, but lots of architecture-specific updates.
ARM:
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- various optimizations to the vgic save/restore code.
PPC:
- enabled KVM-VFIO integration ("VFIO device")
- optimizations to speed up IPIs between vcpus
- in-kernel handling of IOMMU hypercalls
- support for dynamic DMA windows (DDW).
s390:
- provide the floating point registers via sync regs;
- separated instruction vs. data accesses
- dirty log improvements for huge guests
- bugfixes and documentation improvements.
x86:
- Hyper-V VMBus hypercall userspace exit
- alternative implementation of lowest-priority interrupts using
vector hashing (for better VT-d posted interrupt support)
- fixed guest debugging with nested virtualizations
- improved interrupt tracking in the in-kernel IOAPIC
- generic infrastructure for tracking writes to guest
memory - currently its only use is to speedup the legacy shadow
paging (pre-EPT) case, but in the future it will be used for
virtual GPUs as well
- much cleanup (LAPIC, kvmclock, MMU, PIT), including ubsan fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (217 commits)
KVM: x86: remove eager_fpu field of struct kvm_vcpu_arch
KVM: x86: disable MPX if host did not enable MPX XSAVE features
arm64: KVM: vgic-v3: Only wipe LRs on vcpu exit
arm64: KVM: vgic-v3: Reset LRs at boot time
arm64: KVM: vgic-v3: Do not save an LR known to be empty
arm64: KVM: vgic-v3: Save maintenance interrupt state only if required
arm64: KVM: vgic-v3: Avoid accessing ICH registers
KVM: arm/arm64: vgic-v2: Make GICD_SGIR quicker to hit
KVM: arm/arm64: vgic-v2: Only wipe LRs on vcpu exit
KVM: arm/arm64: vgic-v2: Reset LRs at boot time
KVM: arm/arm64: vgic-v2: Do not save an LR known to be empty
KVM: arm/arm64: vgic-v2: Move GICH_ELRSR saving to its own function
KVM: arm/arm64: vgic-v2: Save maintenance interrupt state only if required
KVM: arm/arm64: vgic-v2: Avoid accessing GICH registers
KVM: s390: allocate only one DMA page per VM
KVM: s390: enable STFLE interpretation only if enabled for the guest
KVM: s390: wake up when the VCPU cpu timer expires
KVM: s390: step the VCPU timer while in enabled wait
KVM: s390: protect VCPU cpu timer with a seqcount
KVM: s390: step VCPU cpu timer during kvm_run ioctl
...
Yes, all of these are needed. :) This is admittedly a bit odd, but
kvm-unit-tests access.flat tests this if you run it with "-cpu host"
and of course ept=0.
KVM runs the guest with CR0.WP=1, so it must handle supervisor writes
specially when pte.u=1/pte.w=0/CR0.WP=0. Such writes cause a fault
when U=1 and W=0 in the SPTE, but they must succeed because CR0.WP=0.
When KVM gets the fault, it sets U=0 and W=1 in the shadow PTE and
restarts execution. This will still cause a user write to fault, while
supervisor writes will succeed. User reads will fault spuriously now,
and KVM will then flip U and W again in the SPTE (U=1, W=0). User reads
will be enabled and supervisor writes disabled, going back to the
originary situation where supervisor writes fault spuriously.
When SMEP is in effect, however, U=0 will enable kernel execution of
this page. To avoid this, KVM also sets NX=1 in the shadow PTE together
with U=0. If the guest has not enabled NX, the result is a continuous
stream of page faults due to the NX bit being reserved.
The fix is to force EFER.NX=1 even if the CPU is taking care of the EFER
switch. (All machines with SMEP have the CPU_LOAD_IA32_EFER vm-entry
control, so they do not use user-return notifiers for EFER---if they did,
EFER.NX would be forced to the same value as the host).
There is another bug in the reserved bit check, which I've split to a
separate patch for easier application to stable kernels.
Cc: stable@vger.kernel.org
Cc: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Fixes: f6577a5fa1
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- Various optimizations to the vgic save/restore code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rpvb
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.6
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- Various optimizations to the vgic save/restore code
Conflicts:
include/uapi/linux/kvm.h
kvm_lpage_info->write_count is used to detect if the large page mapping
for the gfn on the specified level is allowed, rename it to disallow_lpage
to reflect its purpose, also we rename has_wrprotected_page() to
mmu_gfn_lpage_is_disallowed() to make the code more clearer
Later we will extend this mechanism for page tracking: if the gfn is
tracked then large mapping for that gfn on any level is not allowed.
The new name is more straightforward
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The highlights are:
* Enable VFIO device on PowerPC, from David Gibson
* Optimizations to speed up IPIs between vcpus in HV KVM,
from Suresh Warrier (who is also Suresh E. Warrier)
* In-kernel handling of IOMMU hypercalls, and support for dynamic DMA
windows (DDW), from Alexey Kardashevskiy.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The existing KVM_CREATE_SPAPR_TCE only supports 32bit windows which is not
enough for directly mapped windows as the guest can get more than 4GB.
This adds KVM_CREATE_SPAPR_TCE_64 ioctl and advertises it
via KVM_CAP_SPAPR_TCE_64 capability. The table size is checked against
the locked memory limit.
Since 64bit windows are to support Dynamic DMA windows (DDW), let's add
@bus_offset and @page_shift which are also required by DDW.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To configure the virtual PMUv3 overflow interrupt number, we use the
vcpu kvm_device ioctl, encapsulating the KVM_ARM_VCPU_PMU_V3_IRQ
attribute within the KVM_ARM_VCPU_PMU_V3_CTRL group.
After configuring the PMUv3, call the vcpu ioctl with attribute
KVM_ARM_VCPU_PMU_V3_INIT to initialize the PMUv3.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In some cases it needs to get/set attributes specific to a vcpu and so
needs something else than ONE_REG.
Let's copy the KVM_DEVICE approach, and define the respective ioctls
for the vcpu file descriptor.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
To support guest PMUv3, use one bit of the VCPU INIT feature array.
Initialize the PMU when initialzing the vcpu with that bit and PMU
overflow interrupt set.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds real and virtual mode handlers for the H_PUT_TCE_INDIRECT and
H_STUFF_TCE hypercalls for user space emulated devices such as IBMVIO
devices or emulated PCI. These calls allow adding multiple entries
(up to 512) into the TCE table in one call which saves time on
transition between kernel and user space.
The current implementation of kvmppc_h_stuff_tce() allows it to be
executed in both real and virtual modes so there is one helper.
The kvmppc_rm_h_put_tce_indirect() needs to translate the guest address
to the host address and since the translation is different, there are
2 helpers - one for each mode.
This implements the KVM_CAP_PPC_MULTITCE capability. When present,
the kernel will try handling H_PUT_TCE_INDIRECT and H_STUFF_TCE if these
are enabled by the userspace via KVM_CAP_PPC_ENABLE_HCALL.
If they can not be handled by the kernel, they are passed on to
the user space. The user space still has to have an implementation
for these.
Both HV and PR-syle KVM are supported.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The interface for adapter mappings was designed with code in mind
that maps each address only once; let's document this.
Otherwise, duplicate mappings are added to the list, which makes
the code ineffective and uses up the limited amount of mapping
needlessly.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's properly document KVM_S390_VM_CRYPTO and its attributes.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's properly document KVM_S390_VM_TOD and its attributes.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The KVM_SMI capability is following the KVM_S390_SET_IRQ_STATE capability
which is "4.95", this changes the number of the KVM_SMI chapter to 4.96.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While the userspace interface requests the maximum size the gmap code
expects to get a maximum address.
This error resulted in bigger page tables than necessary for some guest
sizes, e.g. a 2GB guest used 3 levels instead of 2.
At the same time we introduce KVM_S390_NO_MEM_LIMIT, which allows in a
bright future that a guest spans the complete 64 bit address space.
We also switch to TASK_MAX_SIZE for the initial memory size, this is a
cosmetic change as the previous size also resulted in a 4 level pagetable
creation.
Reported-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
At some call sites of rmap_get_first() and rmap_get_next(), BUG_ON is
placed right after the call to detect unrelated sptes which must not be
found in the reverse-mapping list.
Move this check in rmap_get_first/next() so that all call sites, not
just the users of the for_each_rmap_spte() macro, will be checked the
same way.
One thing to keep in mind is that kvm_mmu_unlink_parents() also uses
rmap_get_first() to handle parent sptes. The change will not break it
because parent sptes are present, at least until drop_parent_pte()
actually unlinks them, and not mmio-sptes.
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A new vcpu exit is introduced to notify the userspace of the
changes in Hyper-V SynIC configuration triggered by guest writing to the
corresponding MSRs.
Changes v4:
* exit into userspace only if guest writes into SynIC MSR's
Changes v3:
* added KVM_EXIT_HYPERV types and structs notes into docs
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SynIC (synthetic interrupt controller) is a lapic extension,
which is controlled via MSRs and maintains for each vCPU
- 16 synthetic interrupt "lines" (SINT's); each can be configured to
trigger a specific interrupt vector optionally with auto-EOI
semantics
- a message page in the guest memory with 16 256-byte per-SINT message
slots
- an event flag page in the guest memory with 16 2048-bit per-SINT
event flag areas
The host triggers a SINT whenever it delivers a new message to the
corresponding slot or flips an event flag bit in the corresponding area.
The guest informs the host that it can try delivering a message by
explicitly asserting EOI in lapic or writing to End-Of-Message (EOM)
MSR.
The userspace (qemu) triggers interrupts and receives EOM notifications
via irqfd with resampler; for that, a GSI is allocated for each
configured SINT, and irq_routing api is extended to support GSI-SINT
mapping.
Changes v4:
* added activation of SynIC by vcpu KVM_ENABLE_CAP
* added per SynIC active flag
* added deactivation of APICv upon SynIC activation
Changes v3:
* added KVM_CAP_HYPERV_SYNIC and KVM_IRQ_ROUTING_HV_SINT notes into
docs
Changes v2:
* do not use posted interrupts for Hyper-V SynIC AutoEOI vectors
* add Hyper-V SynIC vectors into EOI exit bitmap
* Hyper-V SyniIC SINT msr write logic simplified
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
handling.
PPC: Mostly bug fixes.
ARM: No big features, but many small fixes and prerequisites including:
- a number of fixes for the arch-timer
- introducing proper level-triggered semantics for the arch-timers
- a series of patches to synchronously halt a guest (prerequisite for
IRQ forwarding)
- some tracepoint improvements
- a tweak for the EL2 panic handlers
- some more VGIC cleanups getting rid of redundant state
x86: quite a few changes:
- support for VT-d posted interrupts (i.e. PCI devices can inject
interrupts directly into vCPUs). This introduces a new component (in
virt/lib/) that connects VFIO and KVM together. The same infrastructure
will be used for ARM interrupt forwarding as well.
- more Hyper-V features, though the main one Hyper-V synthetic interrupt
controller will have to wait for 4.5. These will let KVM expose Hyper-V
devices.
- nested virtualization now supports VPID (same as PCID but for vCPUs)
which makes it quite a bit faster
- for future hardware that supports NVDIMM, there is support for clflushopt,
clwb, pcommit
- support for "split irqchip", i.e. LAPIC in kernel + IOAPIC/PIC/PIT in
userspace, which reduces the attack surface of the hypervisor
- obligatory smattering of SMM fixes
- on the guest side, stable scheduler clock support was rewritten to not
require help from the hypervisor.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWO2IQAAoJEL/70l94x66D/K0H/3AovAgYmJQToZlimsktMk6a
f2xhdIqfU5lIQQh5uNBCfL3o9o8H9Py1ym7aEw3fmztPHHJYc91oTatt2UEKhmEw
VtZHp/dFHt3hwaIdXmjRPEXiYctraKCyrhaUYdWmUYkoKi7lW5OL5h+S7frG2U6u
p/hFKnHRZfXHr6NSgIqvYkKqtnc+C0FWY696IZMzgCksOO8jB1xrxoSN3tANW3oJ
PDV+4og0fN/Fr1capJUFEc/fejREHneANvlKrLaa8ht0qJQutoczNADUiSFLcMPG
iHljXeDsv5eyjMtUuIL8+MPzcrIt/y4rY41ZPiKggxULrXc6H+JJL/e/zThZpXc=
=iv2z
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"First batch of KVM changes for 4.4.
s390:
A bunch of fixes and optimizations for interrupt and time handling.
PPC:
Mostly bug fixes.
ARM:
No big features, but many small fixes and prerequisites including:
- a number of fixes for the arch-timer
- introducing proper level-triggered semantics for the arch-timers
- a series of patches to synchronously halt a guest (prerequisite
for IRQ forwarding)
- some tracepoint improvements
- a tweak for the EL2 panic handlers
- some more VGIC cleanups getting rid of redundant state
x86:
Quite a few changes:
- support for VT-d posted interrupts (i.e. PCI devices can inject
interrupts directly into vCPUs). This introduces a new
component (in virt/lib/) that connects VFIO and KVM together.
The same infrastructure will be used for ARM interrupt
forwarding as well.
- more Hyper-V features, though the main one Hyper-V synthetic
interrupt controller will have to wait for 4.5. These will let
KVM expose Hyper-V devices.
- nested virtualization now supports VPID (same as PCID but for
vCPUs) which makes it quite a bit faster
- for future hardware that supports NVDIMM, there is support for
clflushopt, clwb, pcommit
- support for "split irqchip", i.e. LAPIC in kernel +
IOAPIC/PIC/PIT in userspace, which reduces the attack surface of
the hypervisor
- obligatory smattering of SMM fixes
- on the guest side, stable scheduler clock support was rewritten
to not require help from the hypervisor"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (123 commits)
KVM: VMX: Fix commit which broke PML
KVM: x86: obey KVM_X86_QUIRK_CD_NW_CLEARED in kvm_set_cr0()
KVM: x86: allow RSM from 64-bit mode
KVM: VMX: fix SMEP and SMAP without EPT
KVM: x86: move kvm_set_irq_inatomic to legacy device assignment
KVM: device assignment: remove pointless #ifdefs
KVM: x86: merge kvm_arch_set_irq with kvm_set_msi_inatomic
KVM: x86: zero apic_arb_prio on reset
drivers/hv: share Hyper-V SynIC constants with userspace
KVM: x86: handle SMBASE as physical address in RSM
KVM: x86: add read_phys to x86_emulate_ops
KVM: x86: removing unused variable
KVM: don't pointlessly leave KVM_COMPAT=y in non-KVM configs
KVM: arm/arm64: Merge vgic_set_lr() and vgic_sync_lr_elrsr()
KVM: arm/arm64: Clean up vgic_retire_lr() and surroundings
KVM: arm/arm64: Optimize away redundant LR tracking
KVM: s390: use simple switch statement as multiplexer
KVM: s390: drop useless newline in debugging data
KVM: s390: SCA must not cross page boundaries
KVM: arm: Do not indent the arguments of DECLARE_BITMAP
...
Includes a number of fixes for the arch-timer, introducing proper
level-triggered semantics for the arch-timers, a series of patches to
synchronously halt a guest (prerequisite for IRQ forwarding), some tracepoint
improvements, a tweak for the EL2 panic handlers, some more VGIC cleanups
getting rid of redundant state, and finally a stylistic change that gets rid of
some ctags warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOhgAAAoJEEtpOizt6ddyKS8H/2ZHMTPjo6yChnrusNWy4Qbr
6laPDlzL+g45oMQRwNL7GnM1deRftaxvT2Wi+X84D/6Y/BD6MPds4HgtBfuWcSZ1
CyRJ0Ot/zrxenucSuJuOjq+a9gdizdAczkbB1MfYDULJH8fb6D+7RYLo3zgh4Xo4
pla3L9U6gSWe+YopBjZtZH43m3fwiwSM/v+uHOTIcXrsbR+fEgx/EFSKmA/DUCuo
P5cFO/ceUGu7nATCexu5V82TgR2hvurrsR7mqfwY8YcF6HRM+NEOoS29xWC77v5S
u/F08TKuKQLv0YTEFTyLETI/oEeuC0cHtrRQBNf4+9kXEOzKyXaae0wR/I6X2Ss=
=GMNk
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.4-rc1
Includes a number of fixes for the arch-timer, introducing proper
level-triggered semantics for the arch-timers, a series of patches to
synchronously halt a guest (prerequisite for IRQ forwarding), some tracepoint
improvements, a tweak for the EL2 panic handlers, some more VGIC cleanups
getting rid of redundant state, and finally a stylistic change that gets rid of
some ctags warnings.
Conflicts:
arch/x86/include/asm/kvm_host.h
Correct some old mistakes in the API documentation:
1. VCPU is identified by index (using kvm_get_vcpu() function), but
"cpu id" can be mistaken for affinity ID.
2. Some error codes are wrong.
[ Slightly tweaked some grammer and did some s/CPU index/vcpu_index/
in the descriptions. -Christoffer ]
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Forwarded physical interrupts on arm/arm64 is a tricky concept and the
way we deal with them is not apparently easy to understand by reading
various specs.
Therefore, add a proper documentation file explaining the flow and
rationale of the behavior of the vgic.
Some of this text was contributed by Marc Zyngier and edited by me.
Omissions and errors are all mine.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This patch fix spelling typos in Documentation/virtual/kvm.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch updates the Posted-Interrupts Descriptor when vCPU
is blocked.
pre-block:
- Add the vCPU to the blocked per-CPU list
- Set 'NV' to POSTED_INTR_WAKEUP_VECTOR
post-block:
- Remove the vCPU from the per-CPU list
Signed-off-by: Feng Wu <feng.wu@intel.com>
[Concentrate invocation of pre/post-block hooks to vcpu_block. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wanpeng Li