Adding support to new get_sdw_stream() that can help machine
driver to deal with soundwire stream.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200317092645.5705-1-srinivas.kandagatla@linaro.org
[fix checkpatch error for "void * qcom_swrm_get_sdw_stream"]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to SoundWire Specification Version 1.2.
"A Data Port number X (in the range 0-14) which supports only one
value of WordLength may implement the WordLength field in the
DPX_BlockCtrl1 Register as Read-Only, returning the fixed value of
WordLength in response to reads."
As WSA881x interfaces in PDM mode making the only field "WordLength"
in DPX_BlockCtrl1" fixed and read-only. Behaviour of writing to this
register on WSA881x soundwire slave with Qualcomm Soundwire Controller
is throwing up an error. Not sure how other controllers deal with
writing to readonly registers, but this patch provides a way to avoid
writes to DPN_BlockCtrl1 register by providing a read_only_wordlength
flag in struct sdw_dpn_prop
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200311113545.23773-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver should clear FIFO in PDI, or the previously stored sample data
in FIFO will generate pop noise when stream is started. The soft reset
bit will clear all the FIFO to zero and is self-cleared after that.
Signed-off-by: randerwang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-18-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Enable multi-link (aka multi-master configuration). In this
configuration, updates and commands with the 'ssp_sync' tag will be
deferred and controlled by the gsync hardware signal.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is a good idea on paper, but it's not recommended at all when
operating in multi-master mode. It's also not recommended when doing
bank switches, since the retransmission would happen at the next SSP,
and the command protocol is stuck in the mean time.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In multi-master mode, the IP will only accept SSP intervals with
integer relationships between the frame rate and the gsync frequency.
E.g for a 48kHz frame rate and 4 kHz gsync signal, the SSP interval
can only be 1, 2, 3, 4, 6, 12.
To simplify we only allow one SSP per gsync interval.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel QA reported a very rare case, possibly hardware-dependent, where
a Slave can become UNATTACHED during a clock stop sequence, which
leads to timeouts and failed suspend sequences.
This patch suppresses the handling of all Slave events while this
transition happens. The two cases that matter are:
a) alerts: if the Slave wants to signal an alert condition, it can do
so using the in-band wake, so there's almost no impact with this
patch.
b) sync loss or imp-def reset: in those cases, bringing back the Slave
to functional state requires a complete re-enumeration. It's better to
just ignore this case and restart cleanly, rather than attempt a
'clean' suspend.
Validation results show the timeouts no longer visible with this patch.
GitHub issue: https://github.com/thesofproject/linux/issues/1678
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After system resumes from S3, io timeout occurs when setting one
unused master on Comet Lake platform. In this case, the master is
reset to default state, and FIFOLEVEL is reset to default value,
but msg_count used for tracing FIFOLEVEL is still with old value,
so FIFOLEVEL will not be set if a new msg FIFO usage is equal to
the old msg_count.
This patch updates msg_count to default value of FIFOLEVEL when
resetting master.
Tested on Comet Lake platform.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for clock stop and restart, with two configuration
parameters:
1) when entering the ClockStop mode, Slave-initiated wakes can be
prevented.
2) When exiting the ClockStop mode, the caller can request a Bus Reset
(either if all Slaves were configured in ClockStopMode1 or the Master
IP lost context and enumeration is required)
The code handles the case where no Slaves are present by configuring
the IP to treat COMMAND_IGNORED as success.
The exit_reset part can be dealt with in the caller, along with the
required syncArm/syncGo sequence in multi-link mode.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If master is in clock stop state, driver can't modify registers
in master except the registers for clock stop setting.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no need for the clock_stop_exit argument with the latest
implementation
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no point in using update for registers with write mask
as 0xFF, this adds unnecessary traffic on the bus.
Just use sdw_write directly.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312100105.5293-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It seems to be a typo. It makes more sense to return the return value
of sdw_update() instead of the value we want to update.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200227220949.4013-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move bit extractors to macros, so that the definitions can be used by
other drivers parsing the MIPI definitions extracted from firmware
tables (ACPI or DT).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200225170041.23644-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If a SoundWire link is enabled, but there are no Slave devices exposed
in firmware tables for this link, or no Slaves in ATTACHED or ALERT
mode, the CMD_IGNORED/-ENODATA error code on a broadcast write is
perfectly legit.
Filter this case to report errors and let the caller deal with the
CMD_IGNORED case.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SoundWire supports two clock stop modes. Add support to handle the
clock stop modes and add pm_runtime calls in the bus.
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two types of io errors when processing alert event.
a) the Master detects an ALERT status for e.g. a jack event and
invokes the implementation-defined function in the Slave driver to
check the jack status. At this time the codec is just suspended, so io
registers can't be accessed.
b) when waking up from clock stop mode1 state, where the bus needs a
complete re-enumeration, Slave registers can't be accessed until the
enumeration is complete.
This patch resumes the Slave device and waits for initialization
complete when processing slave alert event, so that registers on the
Slave can be accessed without timeouts or io errors.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Before removing the slave device, disable pm_runtime to prevent any
race condition with the resume being executed after the bus and slave
devices are removed.
Since this pm_runtime_disable() is handled in common routines,
implementations of Slave drivers do not need to call it in their
.remove() routine.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When resuming with a bus reset, we need to re-enumerate and restart
from UNATTACHED. The helper added in this patch helps implement a more
robust state machine avoiding race conditions on resume.
The unattach request is stored and will be used by Slave drivers, if
needed: Intel validation exposed a corner case where the Slave device
may transition to D3 when streaming stops, but streaming restarts
before the Master transitions to D3. In that case, the Slave status
was not cleared as UNATTACHED by the Master resuming, and the
wait_for_completion will time out.
When the slave resumes, it can check if a Master-initiated
re-enumeration and initialization took place and skip the
wait_for_completion() if there is no reason to wait.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While handling the Device0, we can safely use sdw_write_no_pm.
This move will also helps us track that all other usages of
sdw_write() happen when the Slave is already enumerated.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for pm_runtime with the appropriate error checks for
sdw_write/read functions, e.g. when pm_runtime is not supported.
Also expose internal functions without pm_runtime support, which are
required to perform any sort of suspend/resume operation, as well as
any enumeration tasks.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Waiting for the enumeration to be complete may not be enough for a
Slave driver, there is a possible race condition between resume
operations and initializations handled in an interrupt thread, which
can results in settings not being fully restored after system or
pm_runtime resume.
This patch builds on the changes added for enumeration_complete,
init_completion() is called when the Slave device becomes UNATTACHED,
as done with enumeration_complete.
The difference with the enumeration_complete case is that complete()
is signaled after the Slave device is fully initialized after the
.update_status() callback is called.
A Slave device driver can decide to wait on either of the two
complete() cases, depending on its initialization code and
requirements.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds the signaling needed for Slave drivers to wait until
the enumeration completes so that race conditions when issuing
read/write commands are avoided. The calls for wait_for_completion()
will be added in codec drivers in follow-up patches.
The order between init_completion() and complete() is deterministic,
the Slave is marked as UNATTACHED either during a Master-initiated
HardReset, or when the hardware detects the Slave no longer reports as
ATTACHED.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver probe takes care of basic initialization and is invoked
when a Slave becomes attached, after a match between the Slave DevID
registers and ACPI/DT entries.
The update_status callback is invoked when a Slave state changes,
e.g. when it is assigned a non-zero Device Number and it reports with
an ATTACHED/ALERT state.
The state change detection is usually hardware-based and based on the
SoundWire frame rate (e.g. double-digit microseconds) while the probe
is a pure software operation, which may involve a kernel module
load. In corner cases, it's possible that the state changes before the
probe completes.
This patch suggests the use of wait_for_completion to avoid races on
startup, so that the update_status callback does not rely on invalid
pointers/data structures.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure all calls to the SoundWire stream API are done and involve
callback. Also kfree the stream name.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sdw stream is allocated and stored in dai to share the sdw runtime
information.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code does not expose a trigger callback, which is very
much required for streaming.
The SoundWire stream is enabled and disabled in trigger function.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code does not expose a prepare operation, which is very
much needed to deal with underflow and resume operations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are too many fields called 'res' so add prefix to make it easier
to track what the structures are.
Pure rename, no functionality change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the Intel QA multi-pipelines test case, there are two pipelines for
playback and capture on the same bus. The test fails with an error
when setting port params:
[ 599.224812] rt711 sdw:0:25d:711:0: invalid dpn_prop direction 1 port_num 0
[ 599.224815] sdw_program_slave_port_params failed -22
[ 599.224819] intel-sdw sdw-master-0: Program transport params failed: -22
[ 599.224822] intel-sdw sdw-master-0: Program params failed: -22
[ 599.224828] sdw_enable_stream: SDW0 Pin2-Playback: done
This problem is root-caused to the programming of the capture stream
ports while it is not yet prepared, the calling sequence is:
(1) hw_params for playback. The playback stream provide the port
information to Bus.
(2) stream_prepare for playback, Transport and port parameters
are computed for playback.
(3) hw_params for capture. The capture stream provide the port
information to Bus, but it has not been prepared so is not
accounted for in the bandwidth allocation.
(4) stream_enable for playback. Program transport and port parameters
for all masters and slaves. Since the transport and port parameters
are not computed for capture stream, sdw_program_slave_port_params
will generate a error when setting port params for capture.
in step (4), we should only program the ports for the stream that have
been prepared. A stream that is only in CONFIGURED state should be
ignored, its ports will be programmed when it becomes PREPARED.
Tested on Comet Lake.
GitHub issue: https://github.com/thesofproject/linux/issues/1637
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code will unconditionally return after dealing with the
first Slave on a link. This return should only happen when there is
an error case.
Tested on Comet Lake platform.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After a system suspend, the ALSA/ASoC core will invoke the .prepare()
callback and a TRIGGER_START when INFO_RESUME is not supported.
Likewise, when an underflow occurs, the .prepare callback will be invoked.
In both cases, the stream can be in DISABLED mode, and will transition
into the PREPARED mode. We however don't want the bus bandwidth to be
recomputed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We don't need to prepare the stream again if the stream is already
prepared.
sdw_prepare_stream() could be called multiple times without calling
sdw_deprepare_stream(). We call sdw_prepare_stream() in the prepare
dai ops and sdw_deprepare_stream() in the hw_free dai ops. If an xrun
happens, sdw_prepare_stream() will be called but
sdw_deprepare_stream() will not, which results in an imbalance and an
invalid total bandwidth.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The state machine and notes don't accurately explain or allow
transitions from STREAM_DEPREPARED and STREAM_DISABLED.
Add more explanations and allow for more transitions as a result of a
trigger_stop(), trigger_suspend() and prepare(), depending on the
ALSA/ASoC layer behavior defined by the INFO_RESUME and INFO_PAUSE
flags.
Also add basic checks to help debug inconsistent states and illegal
state machine transitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Somehow Intel folks were confused, the property is 2x what the mclk
frequency actually is (checked the actual bus frequency with a scope)
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113231129.19049-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the programming of the dev_number fails due to an IO error, a new
device_number will be assigned, resulting in a leak.
Make sure we only assign a device_number once per Slave device.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113225637.17313-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix cppcheck warning:
drivers/soundwire/cadence_master.c:992:9: style: Variable 'offset' is
assigned a value that is never used. [unreadVariable]
offset += stream->num_out;
^
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113211025.27973-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Qualcomm SoundWire Master controller is present in most Qualcomm SoCs
either integrated as part of WCD audio codecs via slimbus or
as part of SOC I/O.
This patchset adds support to a very basic controller which has been
tested with WCD934x SoundWire controller connected to WSA881x smart
speaker amplifiers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200113132153.27239-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Before checking for the presence of Device0, we first need to clean-up
the internal state of Slaves that are no longer attached.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a Slave reports multiple status in the sticky bits, find the
latest configuration from the mirror of the PING frame status and
update the status directly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Config only needs to be updated when setting MCP_Config, MCP_Control
and MCP_CmdCtrl to make these register setting effective. When updating
config in master, master will communicate with slave to update status.
Communication will be failed when masters and slaves are in clock stop
state, and this unnecessary config update makes interrupt setting failed.
Tested on Comet Lake with soundwire enabled
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
make sure all interrupts status are cleared before enabling interrupt
so that there is no unexpected interrupt triggered.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If somehow we read the interrupt status while the IP is not powered
the result is probably undefined or 0xffffffff. We do know that some
of the bits are reserved and read as zero, so use as a filter to
discard invalid configurations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110215731.30747-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Only keep pr_err to flag critical configuration errors that will
typically only happen during system integration.
For errors on prepare/deprepare/enable/disable, the caller can do a
much better job with more information on the DAI and device that
caused the issue.
Suggested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200108175438.13121-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SoundWire DAIs for Intel platform are created in
drivers/soundwire/intel.c, while the communication with the Intel DSP
is all controlled in soc/sof/intel
When the DAI status changes, a callback is used to bridge the gap
between the two subsystems.
The naming of the existing 'config_stream' callback does not map well
with any of ALSA/ASoC concepts. This patch renames it as
'params_stream' to be more self-explanatory.
A new 'free_stream' callback is added in case any resources allocated
in the 'params_stream' stage need to be released. In the SOF
implementation, this is used in the hw_free case to release the DMA
channels over IPC.
These two callbacks now rely on structures which expose the link_id
and alh_stream_id (required by the firmware IPC), instead of a list of
parameters. The 'void *' definitions are changed to use explicit
types, as suggested on alsa-devel during earlier reviews.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current interfaces between ASoC and SoundWire are limited by the
platform_device infrastructure to an init() and exit() (mapped to the
platform driver.probe and .remove)
To help with the platform detection, machine driver selection and
management of power dependencies between DSP and SoundWire IP, the
ASoC side requires:
a) an ACPI scan helper, to report if any devices are exposed in the
DSDT tables, and if any links are disabled by the BIOS.
b) a probe helper that allocates the resources without actually
starting the bus.
c) a startup helper which does start the bus when all power
dependencies are settled.
d) an exit helper to free all resources
e) an interrupt_enable/disable helper, typically invoked after the
startup helper but also used in suspend routines.
This patch moves all required interfaces to sdw_intel.h, mainly to
allow SoundWire and ASoC parts to be merged separately once the header
files are shared between trees.
To avoid compilation issues, the conflicts in intel_init.c are blindly
removed. This would in theory prevent the code from working, but since
there are no users of the Intel Soundwire driver this has no
impact. Functionality will be restored when the removal of platform
devices is complete.
Support for SoundWire + SOF builds will only be provided once all the
required pieces are upstream.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191212014507.28050-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The uniqueID is useful when there are two or more devices of the same
type (identical manufacturer ID, part ID) on the same link.
When there is a single device of a given type on a link, its uniqueID
is irrelevant. It's not uncommon on actual platforms to see variations
of the uniqueID, or differences between devID registers and ACPI _ADR
fields.
This patch suggests a filter on startup to identify 'single' devices
and tag them accordingly. The uniqueID is then not used for the probe,
and the device name omits the uniqueID as well.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022234808.17432-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify the loop with a helper. The only functionality change is that
we continue the loop even with an ACPI error.
Follow-up patches will build on this change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022234808.17432-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The previous formula is incorrect for PDI0/1, the mapping is not
linear but has a discontinuity between PDI1 and PDI2.
This change has no effect on PCM PDIs (same mapping).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022232948.17156-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The use of clock stop is not a requirement, the IP can e.g. be
completely power gated and not detect any wakes while in s2idle/deep
sleep.
For now clock-stop is not supported anyways so the control parameter
is always false. This will be revisited when we add clock stop.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Provide debugfs capability to kick link and devices into hard-reset
(as defined by MIPI). This capability is really useful when some
devices are no longer responsive and/or to check the software handling
of resynchronization.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Multiple changes squashed in single patch to avoid tick-tock effect
and avoid breaking compilation/bisect
1. Per the hardware documentation, all changes to MCP_CONFIG,
MCP_CONTROL, MCP_CMDCTRL and MCP_PHYCTRL need to be validated with a
self-clearing write to MCP_CONFIG_UPDATE. Add a helper and do the
update when the CONFIG is changed.
2. Move interrupt enable after interrupt handler registration
3. Add a new helper to start the hardware bus reset with maximum duration
to make sure the Slave(s) correctly detect the reset pattern and to
ensure electrical conflicts can be resolved.
4. flush command FIFOs
Better error handling will be provided after interrupt disable is
provided in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022235448.17586-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
fix cppcheck warning:
[drivers/soundwire/slave.c:145]: (warning) %x in format string (no. 1)
requires 'unsigned int *' but the argument type is 'signed int *'.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191022233147.17268-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit df72b71921 ("soundwire: intel: add missing headers for
cross-compilation") tried to fix cross compilation but erroneously used
wrong header in one of the file. Fix it by using correct io.h header.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: df72b71921 ("soundwire: intel: add missing headers for cross-compilation")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two issues, likely copy/paste:
1. Use cdns->pcm.num_in instead of stream_num_in for consistency with
the rest of the code. This was not detected earlier since platforms did
not have input-only PDIs.
2. use the correct offset for bi-dir PDM, based on IN and OUT
PDIs. Again this was not detected since PDM was not supported earlier.
Reported-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PDI number should match dai->id, there is no need to track if a PDI is
allocated or not.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PDI0/1 are reserved for Bulk and filtered out in the existing code.
That leads to endless confusions on whether the index is the raw or
corrected one. In addition we will need support for Bulk at some point
so it's just simpler to expose those PDIs and not use it for now than
try to be smart unless we have to remove the smarts.
This patch requires a topology change to use PDIs starting at offset 2
explicitly.
Note that there is a known discrepancy between hardware documentation
and what ALH stream works in practice, future fixes are likely.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing Linux code uses a 1:1 mapping between ports and PDIs, but
still has an independent allocation of ports and PDIs.
Let's simplify the code and remove the port layer by only using PDIs.
This patch does not change any functionality, just removes unnecessary
code.
This will also allow for further simplifications where the PDIs are
not dynamically allocated but instead described in a topology file.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no reason to reserve a range of DAI IDs for SoundWire. This
is not scalable and it's better to let the ASoC core allocate the
dai->id when registering a component.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916192348.467-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is not needed and may generate unmet dependencies when
COMPILE_TEST is used for SOF.
ACPI is required, and should be tested when selecting this option.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190916185739.32184-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This includes DT support thanks to Srini and more work done by Intel
(Pierre) on improving cadence and intel support.
Details:
- Add DT bindings and DT support in core
- Add debugfs support for soundwire properties
- Improvements on streaming handling to core
- Improved handling of Cadence module
- More updates and improvements to Intel driver
-----BEGIN PGP SIGNATURE-----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=UILk
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire updates from Vinod Koul:
"This includes DT support thanks to Srini and more work done by Intel
(Pierre) on improving cadence and intel support.
Summary:
- Add DT bindings and DT support in core
- Add debugfs support for soundwire properties
- Improvements on streaming handling to core
- Improved handling of Cadence module
- More updates and improvements to Intel driver"
* tag 'soundwire-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (30 commits)
soundwire: stream: make stream name a const pointer
soundwire: Add compute_params callback
soundwire: core: add device tree support for slave devices
dt-bindings: soundwire: add slave bindings
soundwire: bus: set initial value to port_status
soundwire: intel: handle disabled links
soundwire: intel: add debugfs register dump
soundwire: cadence_master: add debugfs register dump
soundwire: add debugfs support
soundwire: intel: remove unused variables
soundwire: intel: move shutdown() callback and don't export symbol
soundwire: cadence_master: add kernel parameter to override interrupt mask
soundwire: intel_init: add kernel module parameter to filter out links
soundwire: cadence_master: fix divider setting in clock register
soundwire: cadence_master: make use of mclk_freq property
soundwire: intel: read mclk_freq property from firmware
soundwire: add new mclk_freq field for properties
soundwire: stream: remove unnecessary variable initializations
soundwire: stream: fix disable sequence
soundwire: include mod_devicetable.h to avoid compiling warnings
...
port_status[port_num] are assigned for each port_num in some if
conditions. So some of the port_status may not be initialized.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190829181135.16049-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On most hardware platforms, SoundWire interfaces are pin-muxed with
other interfaces (typically DMIC or I2S) and the status of each link
needs to be checked at boot time.
For Intel platforms, the BIOS provides a menu to enable/disable the
links separately, and the information is provided to the OS with an
Intel-specific _DSD property. The same capability will be added to
revisions of the MIPI DisCo specification.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821185821.12690-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add debugfs file to dump the Intel SoundWire registers
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821185821.12690-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add debugfs file to dump the Cadence master registers.
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821185821.12690-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add base debugfs mechanism for SoundWire bus by creating soundwire
root and master-N and slave-x hierarchy.
Also add SDW Slave SCP, DP0 and DP-N register debug file.
Registers not implemented will print as "XX"
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821185821.12690-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Variables 'nval' and 'i' are no longer used sdw_master_read_intel_prop()
so remove them.
drivers/soundwire/intel.c: In function 'sdw_master_read_intel_prop':
drivers/soundwire/intel.c:829:12: warning: unused variable 'i' [-Wunused-variable]
int nval, i;
^
drivers/soundwire/intel.c:829:6: warning: unused variable 'nval' [-Wunused-variable]
int nval, i;
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 085f4ace10 ("soundwire: intel: read mclk_freq property from firmware")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The code has a set of defaults which may not be relevant in all cases,
add kernel parameter as a helper - mostly for early board bring-up.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The hardware and ACPI info may report the presence of links that are
not physically enabled (e.g. due to pin-muxing or hardware reworks),
which in turn can result in errors being thrown. This shouldn't be the
case for production devices but will happen a lot on development
devices - even more so when they expose a connector.
Even when the ACPI information is correct, it's useful to be able to
only enable the links that need attention - mostly to filter out
dynamic debug messages.
Add a module parameter to filter out such links, e.g. adding the
following config to a file in /etc/modprobe.d will select the second
and third links only.
options soundwire_intel_init sdw_link_mask=0x6
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-16-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code uses an OR operation which would mix the original
divider setting with the new one, resulting in an invalid
configuration that can make codecs hang.
Add the mask definition and use cdns_updatel to update divider
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the prototype and Intel implementation are enabled, use this
property to avoid hard-coded values.
For example for ICL the mclk_freq value is 38.4 MHz while on CNL/CML
it's 24 MHz. The mclk_freq should not be confused with the
max_clk_freq, which si the maximum bus clock. The mclk_freq is
typically tied to the oscillator frequency and does not change between
platforms. The max_clk_freq value is linked to the maximum bandwidth
needed and topology/trace length.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A number of variables don't need to be initialized.
In a couple of cases where we loop on a list of runtimes, the code
handling of the 'bus' variable leads to warnings that it may not be
initialized. Add a specific error case to trap such cases.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When we disable the stream and then call hw_free, two bank switches
will be handled and as a result we re-enable the stream on hw_free.
Make sure the stream is disabled on both banks.
TODO: we need to completely revisit all this and make sure we have a
mirroring mechanism between current and alternate banks.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a prefix for common tables and export 2 helpers to set the frame
shapes based on row/col values.
These changes simplify bandwidth allocation algorithms as well as the
Cadence parts which all need to convert from frame shape to indices
used by the standard. These helpers are used in the following patch.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On all released Intel controllers (CNL/CML/ICL), PDI2 reports an
invalid count, force the correct hardware-supported value
This may have to be revisited with platform-specific values if the
hardware changes, but for now this is good enough.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This should not happen in production systems but we should test for
all callback arguments before invoking the config_stream callback.
Update the prototype to clarify that the first argument is mandatory.
Also use local variable instead of multiple dereferences to improve
readability.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190806005522.22642-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code has a mixed select/depend usage which makes no sense.
config SOUNDWIRE_BUS
tristate
select REGMAP_SOUNDWIRE
config REGMAP_SOUNDWIRE
tristate
depends on SOUNDWIRE_BUS
Let's remove one layer of Kconfig definitions and align with the
solutions used by all other serial links.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190718230215.18675-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Assigning a device number to a Slave will result in additional events
when it reports its status in a PING frame. There is no point in
dealing with all the other devices in a loop, this can be done when a
non-device0 event happens.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190725234032.21152-19-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The bus clash interrupts are generated when the status is one, and
also cleared by writing a one. It's overkill/useless to use an OR when
the bit is already set.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190725234032.21152-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
the values passed by all existing BIOS are fine, let's use them as is.
The existing code must have been needed only on early prototypes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190725234032.21152-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use use fwnode_property_count_uXX() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190723194218.69168-1-andriy.shevchenko@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Updates for 5.3 include:
- module_sdw_driver macro for drivers
- Documentation updates for code-blocks
- Improvement from Pierre on intel and cadence driver
- Clarification of DisCo properties and updates
-----BEGIN PGP SIGNATURE-----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=ZOYI
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire updates for v5.3-rc1
Updates for 5.3 include:
- module_sdw_driver macro for drivers
- Documentation updates for code-blocks
- Improvement from Pierre on intel and cadence driver
- Clarification of DisCo properties and updates
* tag 'soundwire-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: add module_sdw_driver helper macro
docs: soundwire: locking: fix tags for a code-block
soundwire: intel_init: add checks on link numbers
soundwire: fix typo in comments
soundwire: Intel: add log for number of PCM and PDM PDIs
soundwire: cadence_master: check the number of bidir PDIs
soundwire: cadence_master: log Slave status mask on errors
soundwire: cadence_master: use rate_limited dynamic debug
soundwire: rename/clarify MIPI DisCo properties
soundwire: clarify comment
soundwire: mipi-disco: fix clock stop modes
soundwire: rename 'freq' fields
soundwire: mipi-disco: remove master_count property for masters
soundwire: remove master data port properties
soundwire: add port-related definitions
soundwire: mipi_disco: fix master/link error
soundwire: intel: filter SoundWire controller device search
soundwire: cdns: Fix compilation error on arm64
Srinivas Kandagatla fixed by bunch of issues, two in core for locking
and out of bound access and one in intel driver copy-paste
-----BEGIN PGP SIGNATURE-----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=zA8C
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus
Vinod writes:
soundwire fixes for v5.2-rc4
Srinivas Kandagatla fixed by bunch of issues, two in core for locking
and out of bound access and one in intel driver copy-paste
* tag 'soundwire-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: intel: set dai min and max channels correctly
soundwire: stream: fix bad unlock balance
soundwire: stream: fix out of boundary access on port properties
Looks like there is a copy paste error.
This patch fixes it!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
the msg lock is taken for multi-link cases only but released
unconditionally, leading to an unlock balance warning for single-link usages
This patch fixes this.
=====================================
WARNING: bad unlock balance detected!
5.1.0-16506-gc1c383a6f0a2-dirty #1523 Tainted: G W
-------------------------------------
aplay/2954 is trying to release lock (&bus->msg_lock) at:
do_bank_switch+0x21c/0x480
but there are no more locks to release!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
[vkoul: edited the change log as suggested by Pierre]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add mask to correctly read the SoundWire SHIM LCAP register. Only bits
2..0 are meaningful, the rest is about link synchronization and stream
channel mapping. Without this mask, the hardware information would
always be larger than whatever the BIOS would report.
Also trap the case with zero links.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This information will be reflected in debugfs but it's easier to see
as a dmesg log.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is an assumption that the first two PDIs are reserved for Bulk,
so we need to make sure the number of bidir PDIs is indeed larger than
two. If the configuration provided is incorrect, this could lead to
allocating a huge amount of memory.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Slave status mask exposes 4 sticky bits. When the device loses
sync, the IP will report two status but the log will only show that
the device lost sync. The status mask has all the information needed
so let's report it instead.
Also change the resolution of the mask, using 64 bits is not needed
when you need 4.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When commands start failing, e.g. due to a bad electrical connection
or bus conflicts, the dmesg log is flooded. This should not happen for
production devices but it's quite frequent when bringing-up a new
platform.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing definitions are ambiguous and possibly misleading.
For DP0, 'flow-control' is only relevant for the BRA protocol and
should not be confused with async modes explicitly not supported for
DP0, add prefix to follow MIPI DisCo definition
The use of 'device_interrupts' is also questionable. The MIPI
SoundWire spec defines Slave-, DP0- and DPN-level
implementation-defined interrupts. Using the 'device' prefix in the
last two cases is misleading, not only is the term 'device' overloaded
but these properties are only valid at the DP0 and DPn levels. Rename
to follow the MIPI definitions, no need to be creative here.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix support for clock_stop_mode0 and 1. The existing code uses a
bitmask between enums, one of which being zero. Or-ing with zero is
not very useful in general...Fix by or-ing with a BIT dependent on the
enum value.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rename all fields with 'freq' as 'clk_freq' to follow the MIPI
specification and avoid confusion between bus clock and audio clocks.
No functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The MIPI DisCo specification for SoundWire defines the
"mipi-sdw-link-N-subproperties" for slaves and
"mipi-sdw-master-N-subproperties" for controllers. This is a mistake
that was not identified until now.
Existing Intel DSDT tables use 'link' everywhere, and the MIPI spec
will be updated to deprecate "mipi-sdw-master-N-subproperties"
Fix to parse firmware information on existing devices. If we ever see
a system with 'master-N-subproperties' I guess we'll have to try both.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The convention is that the SoundWire controller device is a child of
the HDAudio controller. However there can be more than one child
exposed in the DSDT table, and the current namespace walk returns the
last (incorrect) device.
Intel documentation states that bits 28..31 of the _ADR field
represent the link type, with SoundWire assigned the value 4.
Add a filter and terminate early when a valid _ADR is provided,
otherwise keep iterating to find the next child.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On arm64 the cadence_master.c file doesn't compile.
readl and writel are undefined.
This patch fixes that by including io.h.
Signed-off-by: Jan Kotas <jank@cadence.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Assigning local iterator to array element and using it again for
indexing would cross the array boundary.
Fix this by directly referring array element without using the local
variable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For improving code readability it helps to have a blank line between
function so add when missing.
Checkpatch complains:
CHECK: Please use a blank line after function/struct/union/enum
declarations
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Found few more typos in the code, fix them
CHECK: 'and and' may be misspelled - perhaps 'and'?
CHECK: 'smaple' may be misspelled - perhaps 'sample'?
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the code to avoid multiple assignments by assigning to variable
after error checks in soundwire bus.
CHECK: multiple assignments should be avoided
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Found few more issues reported checkpatch on code alignment so fix those
as well in the intel module.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Found few more issues reported checkpatch on code alignment so fix those
as well in the soundwire core.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux code style doesn't expect empty lines after braces and
gives warning:
CHECK: Blank lines aren't necessary after an open brace '{'
Remove the empty line in intel module
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux code style doesn't expect empty lines after braces and
gives warning:
CHECK: Blank lines aren't necessary after an open brace '{'
Remove the empty line in cadence lib
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux code style doesn't expect empty lines before or after braces and
gives warning:
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
Fix these instances in soundwire core
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move to help format instead of --help-- as that is not recommended and
this makes file consistent with other instance
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason the newlines are not used everywhere. Fix as needed.
Reported-by: Joe Perches <joe@perches.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for explicit test against true
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for explicit test against true
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for explicit test against true
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use Linux style. In some cases parenthesis alignment is modified to
keep the code readable.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tools complain here and the location of the newline does not improve
readability.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
no need for an explicit test against false
reported by Coccinelle
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
and make the code more readable
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move to the regular help format, --help-- is no longer recommended.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two files are implicitly relying on an instance of including
module.h from <linux/acpi.h>.
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
Here, we make those includes explicit, in order to allow a future
removal of module.h from linux/acpi.h without causing build breakage.
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
no need to reset return value.
Detected with cppcheck:
[drivers/soundwire/stream.c:332]: (style) Variable 'ret' is assigned a
value that is never used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need for explicit initialization of page and ssp fields, they are
already zeroed with a memset.
Detected with cppcheck:
[drivers/soundwire/bus.c:309]: (style) Variable 'msg->page' is
reassigned a value before the old one has been used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
the number of elements and size are inverted, fix.
This probably only worked because the number of properties is
hard-coded to 1.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The snd_soc_dai_ops structures are only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structures
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In case of error, we can dereference uninitialized 'adev'
drivers/soundwire/intel_init.c:154 sdw_intel_acpi_cb()
error: uninitialized symbol 'adev'.
Fix that by not using adev for warn print and make it pr_err.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To support multi link on Intel platforms, we need to update
SDW SHIM registers.
So, add pre/post bank switch ops for the same in Intel driver.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A multi link bankswitch can be done if the hardware supports and
the stream is handled by multiple Master(s).
This preparatory patch adds support to track m_rt in a stream.
Modifying m_rt_count and usage is added as part of the next patch.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In cases of multiple Masters in a stream, synchronization
between multiple Master(s) is achieved by performing bank switch
together and using Master methods.
Add sdw_ml_bank_switch() to wait for completion of bank switch.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For each SoundWire stream operation, we need to parse master
list and operate upon all master runtime.
This is a preparatory patch to do the boilerplate conversion
of stream handling from single master runtime to handle a
list of master runtime. The code to support bank switch for
multiple master instances is added in the next patch.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, the stream concept is limited to single Master and one
or more Codecs.
This patch extends the concept to support multiple Master(s)
sharing the same reference clock and synchronized in the hardware.
Modify sdw_stream_runtime to support a list of sdw_master_runtime
for the same. The existing reference to a single m_rt is removed
in the next patch.
Typically to lock, one would acquire a global lock and then lock
bus instances. In this case, the caller framework(ASoC DPCM)
guarantees that stream operations on a card are always serialized.
So, there is no race condition and hence no need for global lock.
Bus lock(s) are acquired to reconfigure the bus while the stream
is set-up.
So, we add sdw_acquire_bus_lock()/sdw_release_bus_lock() APIs which
are used only to reconfigure the bus.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Deferred messages are async messages used to synchronize
transitions mostly while doing a bank switch on multi links.
On successful transitions these messages are marked complete
and thereby confirming that all the buses performed bank switch
successfully.
So, initialize the completion structure for the same.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As part of sdw_stream_remove_master(), sdw_stream_remove_slave() is called
which results in bus lock being acquired twice.
So, fix it by performing specific Slave remove operations in
sdw_release_master_stream() instead of calling sdw_stream_remove_slave().
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In sdw_stream_add_master() after the Master ports are configured,
the stream is released incorrectly.
So, fix it by avoiding stream release after configuring the Master
for the stream.
While at it, rename the label appropriately.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For a SoundWire stream it is expected that a Slave is added to the
stream before Master is added.
So, move the stream state to CONFIGURED after the first Slave is
added and remove the stream state assignment for Master add.
Along with these changes, add additional comments to explain the same.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked that produced results are valid.
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbXfQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymwCACdFbUy2kWwrpZWSfSBpawfrs75lLMAmwVOe+62
9aDsDWzDVUEFxF20qiE6
=CMJ3
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the "big" char and misc driver patches for 4.18-rc1.
It's not a lot of stuff here, but there are some highlights:
- coreboot driver updates
- soundwire driver updates
- android binder updates
- fpga big sync, mostly documentation
- lots of minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (81 commits)
vmw_balloon: fixing double free when batching mode is off
MAINTAINERS: Add driver-api/fpga path
fpga: clarify that unregister functions also free
documentation: fpga: move fpga-region.txt to driver-api
documentation: fpga: add bridge document to driver-api
documentation: fpga: move fpga-mgr.txt to driver-api
Documentation: fpga: move fpga overview to driver-api
fpga: region: kernel-doc fixes
fpga: bridge: kernel-doc fixes
fpga: mgr: kernel-doc fixes
fpga: use SPDX
fpga: region: change api, add fpga_region_create/free
fpga: bridge: change api, don't use drvdata
fpga: manager: change api, don't use drvdata
fpga: region: don't use drvdata in common fpga code
Drivers: hv: vmbus: Removed an unnecessary cast from void *
ver_linux: Drop redundant calls to system() to test if file is readable
ver_linux: Move stderr redirection from function parameter to function body
misc: IBM Virtual Management Channel Driver (VMC)
rpmsg: Correct support for MODULE_DEVICE_TABLE()
...
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add DAI registration and DAI ops for the Intel driver along with
callback for topology configuration.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add Intel stream init routines which initialize the Physical
Data Interface (PDI), Audio Link Hub (ALH) and Audio shim.
Also add bank switch routines.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Cadence port management and implement
master port ops.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There can be instances where drivers using Cadence IP might want
to set sdw_master_ops differently per instance of it's use, so
remove the cdns_master_ops and export the APIs.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SoundWire supports two registers banks. So, program the alternate bank
with new configuration and then performs bank switch.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Master and Slave port registers need to be programmed for each port
used in a stream. Add the helpers for port register programming.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add Soundwire port data structures and APIS for initialization
and release of ports.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds APIs and relevant stream data structures
for initialization and release of stream.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
"ret" is an int and "buf" is a u8. sdw_read() returns negative error
codes which are truncated to the u8, 0-255 range before being stored as
an int. It means that "ret" can't be less than zero.
Fixes: b0a9c37b01 ("soundwire: Add slave status handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SoundWire bus needs to select the regmap support. So, add it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the return status ret is being checked but it has not been
updated since the previous check on ret. It appears that assignment of
ret from return status of the call to sdw_cdns_enable_interrupt was
accidentally ommited. Fix this.
Detected by CoverityScan, CID#1463148 ("Logically dead code")
Fixes: 71bb8a1b05 ("soundwire: intel: Add Intel Master driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buf[2] left shift by 24 bits is promoted to int (32 bit signed)
and then signed-extended to unsigned long long. Hence if the upper
bit to buf[2] is set then all the upper bits of addr end up as 1.
Fix this by casting it to u64 before shifting it. Also replace the
unsigned long long casts to u64 casts to match the same type of
addr.
Detected by CoverityScan, CID#1463147 ("Unintended sign extension")
Fixes: d52d7a1be0 ("soundwire: Add Slave status handling helpers")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoundWire Master is implemented as part of Audio controller in
Intel platforms. Add a init module which creates SoundWire Master
platform devices based on the links supported in the hardware.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement sdw_master_ops with support for xfer_msg, xfer_msg_defer
and reset_page_addr. Since Cadence module doesn't know the systems
it will be used, set the read_prop to the bus helper.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add status handling API sdw_handle_slave_status() to handle
Slave status changes.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SoundWire Slaves report status to bus. Add helpers to handle
the status changes.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SoundWire bus supports read or write register(s) for SoundWire Slave
device. sdw_read() and sdw_write() APIs are provided for single
register read/write. sdw_nread() and sdw_nwrite() for operations on
contiguous registers.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MIPI Discovery And Configuration (DisCo) Specification for SoundWire
specifies properties to be implemented for SoundWire Masters and
Slaves. The DisCo spec doesn't mandate these properties. However,
SDW bus cannot work without knowing these values.
The helper functions read the Master and Slave properties.
Implementers of Master or Slave drivers can use any of the below
three mechanisms:
a) Use these APIs here as .read_prop() callback for Master
and Slave
b) Implement own methods and set those as .read_prop(), but invoke
APIs in this file for generic read and override the values with
platform specific data
c) Implement ones own methods which do not use anything provided
here
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Master adds a SoundWire bus instance which scans the firmware
provided for device description.
In this patch we scan ACPI namespaces and create SoundWire
Slave devices based on ACPI description
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the base SoundWire bus type, bus and driver registration.
along with changes to module device table for new SoundWire
device type.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Srinivas Kandagatla