The Cadence IP can inject errors, let's make use of this capability to
test Slave parity error checks.
See e.g. example log where both the master and slave detect the parity
error injected on a dummy read command.
cd /sys/kernel/debug/soundwire/master-1/intel-sdw/
echo 1 > cdns-parity-error-injection
[ 44.756249] intel-master sdw-master-1: Parity error
[ 44.756313] intel-master sdw-master-1: Msg NACK received
[ 44.756366] intel-master sdw-master-1: Msg NACKed for Slave 15
[ 44.756375] intel-master sdw-master-1: trf on Slave 15 failed:-5
[ 44.756382] intel-master sdw-master-1: parity error injection, read: -5
[ 44.756649] rt1308 sdw:1:25d:1308:0: Parity error detected
The code makes sure the Master device is resumed, hence the clock
restarted, before sending a parity error.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Provide prototype and export symbol to enable tests. The bus lock is
handled externally to avoid conflicts e.g. between kernel-generated
traffic and test traffic.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If a Slave device reports with a quirk that its initial parity check
may be incorrect, filter it but keep the parity checks active in
steady state.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some Slaves report incorrect information in their interrupt status
registers after a master/bus reset, track the initial interrupt
handling so that quirks can be introduced to filter out incorrect
information while keeping interrupts enabled in steady state.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Unlike the traditional usage, in the SoundWire specification the
interrupt masks only gate the propagation of an interrupt condition to
the PING frame status. They do not gate the changes of the INT_STAT
registers, which will happen regardless of the mask settings. See
Figure 116 of the SoundWire 1.2 specification for an in-depth
description of the interrupt model.
When the bus driver reads the SCP_INT1_STAT register, it will retrieve
all the interrupt status, including for the mask fields that were not
explicitly set. For example, even if the PARITY mask is not set, the
PARITY error status will be reported if an implementation-defined
interrupt for jack detection is enabled and occurs.
Filtering undesired interrupt reports and handling has to be
implemented in software. This patch enables this filtering for the
INT1_IMPL_DEF, PARITY and BUS_CLASH interrupt sources.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200908134521.6781-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a slave-level property and program the SCP_INT1_MASK as desired by
the codec driver. Since there is no DisCo property this has to be an
implementation-specific firmware property or hard-coded in the driver.
The only functionality change is that implementation-defined
interrupts are no longer set for amplifiers - those interrupts are
typically for jack detection or acoustic event detection/hotwording.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200908134521.6781-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix slimbus case being broken thanks to a typo.
Fixes: 5bd773242f ("soundwire: qcom: avoid dependency on CONFIG_SLIMBUS")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200908140818.28373-1-jonathan@marek.ca
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In system suspend stress cases, the SOF CI reports timeouts. The root
cause is that an alert is generated while the system suspends. The
interrupt handling generates transactions on the bus that will never
be handled because the interrupts are disabled in parallel.
As a result, the transaction never completes and times out on resume.
This error doesn't seem too problematic since it happens in a work
queue, and the system recovers without issues.
Nevertheless, this race condition should not happen. When doing a
system suspend, or when disabling interrupts, we should make sure the
current transaction can complete, and prevent new work from being
queued.
BugLink: https://github.com/thesofproject/linux/issues/2344
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200817222340.18042-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a compatible string for HW version v1.5.1 on sm8250 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200905173905.16541-5-jonathan@marek.ca
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver may be used without slimbus, so don't depend on slimbus.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200905173905.16541-3-jonathan@marek.ca
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The function name qcom_swrm_abh_reg_read should say ahb, fix that.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200905173905.16541-2-jonathan@marek.ca
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the stream is handled at the dai-link level (in the machine
driver), we can remove the stream handling at the dai level. We still
need these callbacks to perform dai-level resource handling
(i.e. addition/removal of a master).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903204739.31206-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the stream trigger is handled at the dai-link level, there is
no need for a dai-level trigger any longer.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903204739.31206-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
snd_soc_dai_get_sdw_stream() can only return the pointer to stream or
an ERR_PTR value, NULL is not a possible value.
Fixes: 09553140c8 ('soundwire: intel: implement get_sdw_stream() operations')
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903204739.31206-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
snd_soc_dai_get_sdw_stream() can only return -ENOTSUPP or the stream,
NULL is not a possible value.
Fixes: 4550569bd7 ('soundwire: stream: add helper to startup/shutdown streams')
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903204739.31206-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
use FIELD_{GET|PREP} in intel_init driver to get/set field values
instead of open coding masks and shift operations.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903114504.1202143-9-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
use FIELD_{GET|PREP} in intel driver to get/set field values instead of
open coding masks and shift operations.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903114504.1202143-8-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
use FIELD_{GET|PREP} in cadence driver to get/set field values instead
of open coding masks and shift operations.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903114504.1202143-7-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
use FIELD_{GET|PREP} in qcom driver to get/set field values instead of
open coding masks and shift operations.
Also, remove now unused register shift defines
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903114504.1202143-6-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
use FIELD_{GET|PREP} in stream code to get/set field values instead of
open coding masks and shift operations.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903114504.1202143-5-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
use SDW_DISCO_LINK_ID() in slave code to extract field values instead of
open coding masks and shift operations to extract link_id
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903114504.1202143-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
use FIELD_GET() in bus code to extract field values instead of open
coding masks and shift operations.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200903114504.1202143-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Each link has separate power controls, but experimental results show
we need to use an all-or-none approach to the link power management.
This change has marginal power impacts, the DSP needs to be powered
anyways before SoundWire links can be powered, and even when powered a
link can be in clock-stopped mode.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While the hardware exposes independent bits to power-up each master,
the recommended sequence is to power all links or none. Idle links can
still use the clock stop mode while the master is powered.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Detect cases where the clock is assumed to be stopped but the IP is
not in the relevant state. There is no real way to recover here, but
adding an error log can help detect bad programming sequences or race
conditions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use platform-specific information to decide when to use hw_sync, not
only a number of links > 1.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Deal with the BUS_RESET case, which is the default. The only change is
to add support for the exit sequence using the syncArm/syncGo mode for
the exit reset sequence.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The multi-link support is enabled with a hardware gsync signal
connecting all links. All commands and operations which typically are
handled on an SSP boundary will be deferred further and enabled across
all links with the 'syncGo' sequence.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200901150556.19432-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code allocates memory for the total number of ports.
This only works if the ports are contiguous, but will break if e.g. a
Devices uses port0, 1, and 14. The port_ready[] array would contain 3
elements, which would lead to an out-of-bounds access. Conversely in
other cases, the wrong port index would be used leading to timeouts on
prepare.
This can be fixed by allocating for the worst-case of 15
ports (DP0..DP14). In addition since the number is now fixed, we can
use an array instead of a dynamic allocation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200831134318.11443-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
clang static analysis flags this problem
stream.c:844:9: warning: Use of memory after
it is freed
kfree(bus->defer_msg.msg->buf);
^~~~~~~~~~~~~~~~~~~~~~~
This happens in an error handler cleaning up memory
allocated for elements in a list.
list_for_each_entry(m_rt, &stream->master_list, stream_node) {
bus = m_rt->bus;
kfree(bus->defer_msg.msg->buf);
kfree(bus->defer_msg.msg);
}
And is triggered when the call to sdw_bank_switch() fails.
There are a two problems.
First, when sdw_bank_switch() fails, though it frees memory it
does not clear bus's reference 'defer_msg.msg' to that memory.
The second problem is the freeing msg->buf. In some cases
msg will be NULL so this will dereference a null pointer.
Need to check before freeing.
Fixes: 99b8a5d608 ("soundwire: Add bank switch routine")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200902202650.14189-1-trix@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When CONFIG_PM_SLEEP is not defined, GCC throws compilation warnings:
drivers/soundwire/intel.c:1799:12: warning: ‘intel_resume’ defined but not
used [-Wunused-function]
static int intel_resume(struct device *dev)
^~~~~~~~~~~~
drivers/soundwire/intel.c:1683:12: warning: ‘intel_suspend’ defined but not
used [-Wunused-function]
static int intel_suspend(struct device *dev)
^~~~~~~~~~~~~
Fix by using __maybe_unused macro.
Suggested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200824133234.28115-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When all the links are suspended, the HDaudio controller may suspend
and the power rails to the SoundWire IP may be disabled, requiring a
complete re-initialization/enumeration on resume. However, if one or
more Masters remained active, the HDaudio controller will remain active
and the power rails will remain enabled. As a result, during the link
resume step we can check if the context was preserved by verifying if
the clock was stopped, and avoid doing a complete bus reset and
re-enumeration.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-13-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In this mode, on restart the bus restarts immediately, the Slaves
remain synchronized and all context is kept intact.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-12-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When none of the clock stop quirks is specified, the Master IP will
assume the context is preserved and will not reset the Bus and restart
enumeration. Due to power rail dependencies, the HDaudio controller
needs to remain powered and prevented from executing its pm_runtime
suspend routine.
This choice of course has a power impact, and this mode should only be
selected when latency requirements are critical or the parent device
can enter D0ix modes.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In case the clock needs to keep running, we need to prevent the Master
from entering pm_runtime suspend.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move existing pm_runtime suspend under the CLK_STOP_TEARDOWN case.
In this mode the Master IP will lose all context but in-band wakes are
supported.
On pm_runtime resume a complete re-enumeration will be performed after
a bus reset.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that we have options, add support for TEARDOWN mode (same
functionality as existing code)
All other modes will be added in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add quirk and pm_runtime idle scheduling to let the Master suspend if
no Slaves become attached. This can happen when a link is not marked
as disabled and has devices exposed in the DSDT, if the power is
controlled by sideband means or the link includes a pluggable
connector.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .prepare() callback is invoked for normal streaming, underflows or
during the system resume transition. In the latter case, the context
for the ALH PDIs is lost, and the DSP is not initialized properly
either, but the bus parameters don't need to be recomputed.
Conversely, when doing a regular .prepare() during an underflow, the
ALH/SHIM registers shall not be changed as the hardware cannot be
reprogrammed after the DMA started (hardware spec requirement).
This patch adds storage of PDI and hw_params in the DAI dma context,
and the difference between the types of .prepare() usages is handled
via a simple boolean, updated when suspending, and tested for in the
.prepare() case.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This helps make sure they are all UNATTACHED and reset the state
machines.
At the moment we perform a bus reset both for system resume and
pm_runtime resume, this will be modified when clock-stop mode is
supported
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Previous patches took care of the case where the master device is
pm_runtime 'suspended' when a system suspend occurs.
In the case where the master device was not suspended, e.g. if suspend
occurred while streaming audio, Intel validation noticed a race
condition: the pm_runtime suspend may conflict with the enumeration
started by the system resume.
This can be simply fixed by updating the status before exiting system
resume.
GitHub issue: https://github.com/thesofproject/linux/issues/1482
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The system resume does the entire bus re-initialization and brings it
to full-power. If the device was pm_runtime suspended, there is no
need to run the pm_runtime resume sequence after the system runtime.
Follow the documentation from runtime_pm.rst, and conditionally
disable, set_active and re-enable the device on system resume.
Note that pm_runtime_suspended() is used instead of
pm_runtime_status_suspended() so that we can deal with the case where
pm_runtime is disabled.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add basic hooks in DAI .startup and .shutdown callbacks.
The SoundWire IP should be powered between those two calls. The power
dependencies between SoundWire and DSP are handled with the
parent/child relationship, before the SoundWire master device becomes
active the parent device will become active and power-up the shared
rails.
For now the strategy is to rely on complete enumeration when the
device becomes active, so the code is a copy/paste of the sequence for
system suspend/resume. In future patches, the strategy will optionally
be to rely on clock stop if the enumeration time is prohibitive or
when the devices connected to a link can signal a wake.
A module parameter is added to make integration of new Slave devices
easier, to e.g. keep the device active or prevent clock-stop.
Note that we need to we have to disable runtime pm before device
unregister, otherwise we will see "Failed to power up link: -11" error
on module remove test.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200817152923.3259-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement suspend/resume capabilities (not runtime_pm for now)
The resume part is essentially a full-blown re-enumeration.
When S0ix is supported, we will select clock stop mode when the ACPI
target state is S0, and tear down the link for S3.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200721203723.18305-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The hierarchy of soundwire devices is platform device -> M device -> S
device. A S device is physically attached on the platform device. So the
platform device should be resumed when a S device is resumed. As the
bridge of platform device and S device, we have to implement runtime pm
on M driver. We have set runtime pm ops in M driver already, but still
need to enable runtime pm.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200726215945.3119-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This contains few core changes and bunch of Intel driver updates:
- Adds definitions for 1.2 spec
- Sanyog left as a MAINTAINER and Bard took his place while Sanyog
is a reviewer now.
- Intel: Lots of updates to stream/dai handling, wake support and link
synchronization.
-----BEGIN PGP SIGNATURE-----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=De+P
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire updates for 5.9-rc1
This contains few core changes and bunch of Intel driver updates:
- Adds definitions for 1.2 spec
- Sanyog left as a MAINTAINER and Bard took his place while Sanyog
is a reviewer now.
- Intel: Lots of updates to stream/dai handling, wake support and link
synchronization.
* tag 'soundwire-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (31 commits)
Soundwire: intel_init: save Slave(s) _ADR info in sdw_intel_ctx
soundwire: intel: add wake interrupt support
soundwire: intel/cadence: merge Soundwire interrupt handlers/threads
soundwire: intel_init: use EXPORT_SYMBOL_NS
soundwire: intel_init: add implementation of sdw_intel_enable_irq()
soundwire: intel: introduce helper for link synchronization
soundwire: intel: introduce a helper to arm link synchronization
soundwire: intel: revisit SHIM programming sequences.
soundwire: intel: reuse code for wait loops to set/clear bits
soundwire: fix the kernel-doc comment
soundwire: sdw.h: fix indentation
soundwire: sdw.h: fix PRBS/Static_1 swapped definitions
soundwire: intel: don't free dma_data in DAI shutdown
soundwire: cadence: allocate/free dma_data in set_sdw_stream
soundwire: intel: remove stream allocation/free
soundwire: stream: add helper to startup/shutdown streams
soundwire: intel: implement get_sdw_stream() operations
MAINTAINERS: change SoundWire maintainer
soundwire: bus: initialize bus clock base and scale registers
soundwire: extend SDW_SLAVE_ENTRY
...
Save ACPI information in context so that we can match machine driver
with sdw _ADR matching tables.
Suggested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When system is suspended in clock stop mode on intel platforms, both
master and slave are in clock stop mode and soundwire bus is taken
over by a glue hardware. The bus message for jack event is processed
by this glue hardware, which will trigger an interrupt to resume audio
pci device. Then audio pci driver will resume soundwire master and slave,
transfer bus ownership to master, finally slave will report jack event
to master and codec driver is triggered to check jack status.
if a slave has been attached to a bus, the slave->dev_num_sticky
should be non-zero, so we can check this value to skip the
ghost devices defined in ACPI table but not populated in hardware.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code uses one pair of interrupt handler/thread per link
but at the hardware level the interrupt is shared. This works fine for
legacy PCI interrupts, but leads to timeouts in MSI (Message-Signaled
Interrupt) mode, likely due to edges being lost.
This patch unifies interrupt handling for all links. The dedicated
handler is removed since we use a common one for all shared interrupt
sources, and the thread function takes care of dealing with interrupt
sources. This partition follows the model used for the SOF IPC on
HDaudio platforms, where similar timeout issues were noticed and doing
all the interrupt handling/clearing in the thread improved
reliability/stability.
Validation results with 4 links active in parallel show a night-and-day
improvement with no timeouts noticed even during stress tests. Latency
and quality of service are not affected by the change - mostly because
events on a SoundWire link are throttled by the bus frame rate
(typically 8..48kHz).
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure all symbols in this soundwire-intel-init module are exported
with a namespace.
The MODULE_IMPORT_NS will be used in Intel/SOF HDaudio modules to be
posted in a separate series.
Namespaces are only introduced for the Intel parts of the SoundWire
code at this time, in future patches we should also add namespaces for
Cadence parts and the SoundWire core.
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This function is required to enable all interrupts across all links.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After arming the synchronization, the SYNCGO field controls the
hardware-based synchronization between links.
Move the programming and wait for clear of SYNCGO to dedicated helper.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move code from pre_bank_switch to dedicated helper, will be used in
follow-up patches as recommended by programming flows.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Somehow the existing code is not aligned with the steps described in
the documentation, refactor code and make sure the register
programming sequences are correct. Also add missing power-up,
power-down and wake capabilities (the last two are used in follow-up
patches but introduced here for consistency).
Some of the SHIM registers exposed fields that are link specific, and
in addition some of the power-related registers (SPA/CPA) take time to
be updated. Uncontrolled access leads to timeouts or errors. Add a
mutex, shared by all links, so that all accesses to such registers are
serialized, and follow a pattern of read-modify-write.
This includes making sure SHIM_SYNC is programmed only once, before
the first master is powered on. We use a 'shim_mask' field, shared
between all links and protected by a mutex, to deal with power-up and
power-down sequences.
Note that the SYNCPRD value is tied only to the XTAL value and not the
current bus frequency or the frame rate.
BugLink: https://github.com/thesofproject/linux/issues/1555
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200716150947.22119-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
sdw_startup_stream() and sdw_shutdown_stream() argument has been updated
but not the comments, so update these as well to fix warning with W=1
drivers/soundwire/stream.c:1859: warning: Function parameter or member 'sdw_substream' not described in 'sdw_startup_stream'
drivers/soundwire/stream.c:1859: warning: Excess function parameter 'stream' description in 'sdw_startup_stream'
drivers/soundwire/stream.c:1903: warning: Function parameter or member 'sdw_substream' not described in 'sdw_shutdown_stream'
drivers/soundwire/stream.c:1903: warning: Excess function parameter 'stream' description in 'sdw_shutdown_stream'
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200715095702.1519554-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that the DMA data is allocated/freed in set_sdw_stream(), remove
free operations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200630184356.24939-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current memory allocation is somewhat strange: the dma_data is
allocated in set_sdw_stream, but released in the intel DAI
shutdown. This no longer works with the multi-cpu implementation,
since the dma_data is released in the dai shutdown which takes place
before the dailink shutdown.
Move to a more symmetric allocation where the dma_data is allocated
with non-NULL SoundWire stream, and conversely released when a NULL
stream is provided - for consistency with the stream startup and
shutdown operations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200630184356.24939-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To support streaming across multiple links, the stream allocation/free
needs to be at the dailink level, not the dai.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200630184356.24939-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To handle streams at the dailink level, expose two helpers that will
be called from machine drivers.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200630184356.24939-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is needed to retrieve the information when the stream is
allocated at the dai_link level.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200630184356.24939-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SoundWire 1.2 specification adds new registers to allow for
seamless clock changes while audio transfers are on-going. Program
them following the specification.
Note that dynamic clock changes are not supported for now, this only
adds the register initialization.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200608205436.2402-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SoundWire 1.2 specification adds new capabilities that were not
present in previous version, such as the class ID.
To enable support for class drivers, and well as drivers that address
a specific version, all fields of the sdw_device_id structure need to
be exposed. For SoundWire 1.0 and 1.1 devices, a wildcard is used so
class and version information are ignored.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200608205436.2402-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
qcom_swrm_port_ops and qcom_swrm_ops are not modified and can be made
const to allow the compiler to put them in read-only memory.
Before:
text data bss dec hex filename
18266 3056 256 21578 544a drivers/soundwire/qcom.o
After:
text data bss dec hex filename
18426 2896 256 21578 544a drivers/soundwire/qcom.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200609230029.69802-1-rikard.falkeborn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rather than a plain-vanilla init/exit, this patch provides 3 steps in
the initialization needed for driver selection, machine driver
selection and deal with power rail dependencies.
- ACPI scan: this step is done at a very early stage to detect the
presence of a SoundWire Controller and enabled links at the BIOS
level. This step may be called from the legacy HDaudio driver, which
will abort its probe to let the Sound Open Firmware (SOF) handle the
hardware.
- probe: this step allocates all the required memory and will add a
sdw_bus, which in turn will result in identifying all possible Slaves
listed below the Controller ACPI companion device. All the information
is reported to the parent PCI driver which will select the relevant
machine driver.
- startup: this last step starts the bus reset, which results in Slave
devices reporting as ATTACHED and being enumerated. This step is only
done during the card creation stage, after the DSP is powered to
account for internal power rail dependencies.
These 3 steps are already supported in the Sound Open firmware
drivers and upstream.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It's not clear how this code ever worked, the link information is used
in intel.c but never passed as platform_data.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need to test link_mask twice
Suggested-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The use of drvdata mixes two structures. There was no harm the first
structure is embedded as the first element of the second, but that's
not good. Make sure all drvdata is based on the 'sdw_cdns' structure.
While we are at it, remove indirections for 'dev' and 'cdns' to make
the code more readable.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The code can be simplified a bit to have a more consistent use of
'dev' and 'bus', as well as move definitions around. This will help
make the major changes in follow-up patches easier to review.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200531182102.27840-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dais are allocated with devm_kcalloc() but their name isn't
resourced managed and never freed. Fix by also using devm_ for the dai
names as well.
Fixes: c46302ec55 ('soundwire: intel: Add audio DAI ops')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200617163536.17401-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
`-objs` is designed for building host programs, change to `-y`,
more straightforward for device drivers.
See Documentation/kbuild/makefiles.rst
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200616162140.2563535-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It's not clear why we have two modules for the Intel controller/master
support when there is a single Kconfig. This adds complexity for no
good reason, the two parts need to work together anyways.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200519191903.6557-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Expose MIPI DisCo Slave properties in sysfs.
For Slave properties and Data Port 0, the attributes are managed with
simple devm_ support.
A Slave Device may have more than one Data Port (DPN), and each Data
Port can be sink or source. The attributes are created dynamically
using pre-canned macros, but still use devm_ with a name attribute
group to avoid creating kobjects - as requested by GregKH. In the
_show function, we use container_of() to retrieve port number and
direction required to extract the information.
Audio modes are not supported for now. Depending on the discussions
the SoundWire Device Class, we may add it later as is or follow the
new specification.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200518203551.2053-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the master properties as attributes. The description is directly
derived from the MIPI DisCo specification.
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200518203551.2053-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use more meaningful member names in preparation for sysfs support.
No functionality change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200518203551.2053-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We need to enable runtime_pm on master device with generic helpers,
so that a Slave-initiated wake is propagated to the bus parent.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200518174322.31561-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the existing SoundWire code, Master Devices are not explicitly
represented - only SoundWire Slave Devices are exposed (the use of
capital letters follows the SoundWire specification conventions).
With the existing code, the bus is handled without using a proper device,
and bus->dev typically points to a platform device. The right thing to
do as discussed in multiple reviews is use a device for each bus.
The sdw_master_device addition is done with minimal internal plumbing
and not exposed externally. The existing API based on
sdw_bus_master_add() and sdw_bus_master_delete() will deal with the
sdw_master_device life cycle, which minimizes changes to existing
drivers.
Note that the Intel code will be modified in follow-up patches (no
impact on any platform since the connection with ASoC is not supported
upstream so far).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200518174322.31561-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
this is a preparatory patch before the introduction of the
sdw_master_type. The SoundWire slave support is slightly modified with
the use of a sdw_slave_type, and the uevent handling move to
slave.c (since it's not necessary for the master).
No functionality change other than moving code around.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200518174322.31561-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for future extensions, rename functions to use
sdw_bus_master prefix and add a parent and fwnode argument to
sdw_bus_master_add to help with device registration in follow-up
patches.
No functionality change, just renames and additional arguments.
The Intel code is currently unused, the two additional arguments are
only needed for compilation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20200518174322.31561-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fixes coccicheck error:
drivers/soundwire/qcom.c:815:7-32: ERROR: Threaded IRQ with
no primary handler requested without IRQF_ONESHOT
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1588735553-34219-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need to repeat the same info log on all enumerations (essentially
each power-up), keep it as debug information.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200419185117.4233-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The error handling flow seems incorrect, there is no reason to try and
add debugfs support if the device registration did not
succeed. Return on error.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20200419185117.4233-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Adding support to new get_sdw_stream() that can help machine
driver to deal with soundwire stream.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200317092645.5705-1-srinivas.kandagatla@linaro.org
[fix checkpatch error for "void * qcom_swrm_get_sdw_stream"]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to SoundWire Specification Version 1.2.
"A Data Port number X (in the range 0-14) which supports only one
value of WordLength may implement the WordLength field in the
DPX_BlockCtrl1 Register as Read-Only, returning the fixed value of
WordLength in response to reads."
As WSA881x interfaces in PDM mode making the only field "WordLength"
in DPX_BlockCtrl1" fixed and read-only. Behaviour of writing to this
register on WSA881x soundwire slave with Qualcomm Soundwire Controller
is throwing up an error. Not sure how other controllers deal with
writing to readonly registers, but this patch provides a way to avoid
writes to DPN_BlockCtrl1 register by providing a read_only_wordlength
flag in struct sdw_dpn_prop
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200311113545.23773-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver should clear FIFO in PDI, or the previously stored sample data
in FIFO will generate pop noise when stream is started. The soft reset
bit will clear all the FIFO to zero and is self-cleared after that.
Signed-off-by: randerwang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-18-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Enable multi-link (aka multi-master configuration). In this
configuration, updates and commands with the 'ssp_sync' tag will be
deferred and controlled by the gsync hardware signal.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-17-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is a good idea on paper, but it's not recommended at all when
operating in multi-master mode. It's also not recommended when doing
bank switches, since the retransmission would happen at the next SSP,
and the command protocol is stuck in the mean time.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-15-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In multi-master mode, the IP will only accept SSP intervals with
integer relationships between the frame rate and the gsync frequency.
E.g for a 48kHz frame rate and 4 kHz gsync signal, the SSP interval
can only be 1, 2, 3, 4, 6, 12.
To simplify we only allow one SSP per gsync interval.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel QA reported a very rare case, possibly hardware-dependent, where
a Slave can become UNATTACHED during a clock stop sequence, which
leads to timeouts and failed suspend sequences.
This patch suppresses the handling of all Slave events while this
transition happens. The two cases that matter are:
a) alerts: if the Slave wants to signal an alert condition, it can do
so using the in-band wake, so there's almost no impact with this
patch.
b) sync loss or imp-def reset: in those cases, bringing back the Slave
to functional state requires a complete re-enumeration. It's better to
just ignore this case and restart cleanly, rather than attempt a
'clean' suspend.
Validation results show the timeouts no longer visible with this patch.
GitHub issue: https://github.com/thesofproject/linux/issues/1678
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After system resumes from S3, io timeout occurs when setting one
unused master on Comet Lake platform. In this case, the master is
reset to default state, and FIFOLEVEL is reset to default value,
but msg_count used for tracing FIFOLEVEL is still with old value,
so FIFOLEVEL will not be set if a new msg FIFO usage is equal to
the old msg_count.
This patch updates msg_count to default value of FIFOLEVEL when
resetting master.
Tested on Comet Lake platform.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for clock stop and restart, with two configuration
parameters:
1) when entering the ClockStop mode, Slave-initiated wakes can be
prevented.
2) When exiting the ClockStop mode, the caller can request a Bus Reset
(either if all Slaves were configured in ClockStopMode1 or the Master
IP lost context and enumeration is required)
The code handles the case where no Slaves are present by configuring
the IP to treat COMMAND_IGNORED as success.
The exit_reset part can be dealt with in the caller, along with the
required syncArm/syncGo sequence in multi-link mode.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If master is in clock stop state, driver can't modify registers
in master except the registers for clock stop setting.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no need for the clock_stop_exit argument with the latest
implementation
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200317163329.25501-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no point in using update for registers with write mask
as 0xFF, this adds unnecessary traffic on the bus.
Just use sdw_write directly.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200312100105.5293-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It seems to be a typo. It makes more sense to return the return value
of sdw_update() instead of the value we want to update.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200227220949.4013-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move bit extractors to macros, so that the definitions can be used by
other drivers parsing the MIPI definitions extracted from firmware
tables (ACPI or DT).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200225170041.23644-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If a SoundWire link is enabled, but there are no Slave devices exposed
in firmware tables for this link, or no Slaves in ATTACHED or ALERT
mode, the CMD_IGNORED/-ENODATA error code on a broadcast write is
perfectly legit.
Filter this case to report errors and let the caller deal with the
CMD_IGNORED case.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SoundWire supports two clock stop modes. Add support to handle the
clock stop modes and add pm_runtime calls in the bus.
Credits: this patch is based on an earlier internal contribution by
Vinod Koul, Sanyog Kale, Shreyas Nc and Hardik Shah.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two types of io errors when processing alert event.
a) the Master detects an ALERT status for e.g. a jack event and
invokes the implementation-defined function in the Slave driver to
check the jack status. At this time the codec is just suspended, so io
registers can't be accessed.
b) when waking up from clock stop mode1 state, where the bus needs a
complete re-enumeration, Slave registers can't be accessed until the
enumeration is complete.
This patch resumes the Slave device and waits for initialization
complete when processing slave alert event, so that registers on the
Slave can be accessed without timeouts or io errors.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Before removing the slave device, disable pm_runtime to prevent any
race condition with the resume being executed after the bus and slave
devices are removed.
Since this pm_runtime_disable() is handled in common routines,
implementations of Slave drivers do not need to call it in their
.remove() routine.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When resuming with a bus reset, we need to re-enumerate and restart
from UNATTACHED. The helper added in this patch helps implement a more
robust state machine avoiding race conditions on resume.
The unattach request is stored and will be used by Slave drivers, if
needed: Intel validation exposed a corner case where the Slave device
may transition to D3 when streaming stops, but streaming restarts
before the Master transitions to D3. In that case, the Slave status
was not cleared as UNATTACHED by the Master resuming, and the
wait_for_completion will time out.
When the slave resumes, it can check if a Master-initiated
re-enumeration and initialization took place and skip the
wait_for_completion() if there is no reason to wait.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While handling the Device0, we can safely use sdw_write_no_pm.
This move will also helps us track that all other usages of
sdw_write() happen when the Slave is already enumerated.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for pm_runtime with the appropriate error checks for
sdw_write/read functions, e.g. when pm_runtime is not supported.
Also expose internal functions without pm_runtime support, which are
required to perform any sort of suspend/resume operation, as well as
any enumeration tasks.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Waiting for the enumeration to be complete may not be enough for a
Slave driver, there is a possible race condition between resume
operations and initializations handled in an interrupt thread, which
can results in settings not being fully restored after system or
pm_runtime resume.
This patch builds on the changes added for enumeration_complete,
init_completion() is called when the Slave device becomes UNATTACHED,
as done with enumeration_complete.
The difference with the enumeration_complete case is that complete()
is signaled after the Slave device is fully initialized after the
.update_status() callback is called.
A Slave device driver can decide to wait on either of the two
complete() cases, depending on its initialization code and
requirements.
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds the signaling needed for Slave drivers to wait until
the enumeration completes so that race conditions when issuing
read/write commands are avoided. The calls for wait_for_completion()
will be added in codec drivers in follow-up patches.
The order between init_completion() and complete() is deterministic,
the Slave is marked as UNATTACHED either during a Master-initiated
HardReset, or when the hardware detects the Slave no longer reports as
ATTACHED.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver probe takes care of basic initialization and is invoked
when a Slave becomes attached, after a match between the Slave DevID
registers and ACPI/DT entries.
The update_status callback is invoked when a Slave state changes,
e.g. when it is assigned a non-zero Device Number and it reports with
an ATTACHED/ALERT state.
The state change detection is usually hardware-based and based on the
SoundWire frame rate (e.g. double-digit microseconds) while the probe
is a pure software operation, which may involve a kernel module
load. In corner cases, it's possible that the state changes before the
probe completes.
This patch suggests the use of wait_for_completion to avoid races on
startup, so that the update_status callback does not rely on invalid
pointers/data structures.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200115000844.14695-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make sure all calls to the SoundWire stream API are done and involve
callback. Also kfree the stream name.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sdw stream is allocated and stored in dai to share the sdw runtime
information.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code does not expose a trigger callback, which is very
much required for streaming.
The SoundWire stream is enabled and disabled in trigger function.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code does not expose a prepare operation, which is very
much needed to deal with underflow and resume operations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are too many fields called 'res' so add prefix to make it easier
to track what the structures are.
Pure rename, no functionality change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Sanyog Kale <sanyog.r.kale@intel.com>
Link: https://lore.kernel.org/r/20200215014740.27580-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the Intel QA multi-pipelines test case, there are two pipelines for
playback and capture on the same bus. The test fails with an error
when setting port params:
[ 599.224812] rt711 sdw:0:25d:711:0: invalid dpn_prop direction 1 port_num 0
[ 599.224815] sdw_program_slave_port_params failed -22
[ 599.224819] intel-sdw sdw-master-0: Program transport params failed: -22
[ 599.224822] intel-sdw sdw-master-0: Program params failed: -22
[ 599.224828] sdw_enable_stream: SDW0 Pin2-Playback: done
This problem is root-caused to the programming of the capture stream
ports while it is not yet prepared, the calling sequence is:
(1) hw_params for playback. The playback stream provide the port
information to Bus.
(2) stream_prepare for playback, Transport and port parameters
are computed for playback.
(3) hw_params for capture. The capture stream provide the port
information to Bus, but it has not been prepared so is not
accounted for in the bandwidth allocation.
(4) stream_enable for playback. Program transport and port parameters
for all masters and slaves. Since the transport and port parameters
are not computed for capture stream, sdw_program_slave_port_params
will generate a error when setting port params for capture.
in step (4), we should only program the ports for the stream that have
been prepared. A stream that is only in CONFIGURED state should be
ignored, its ports will be programmed when it becomes PREPARED.
Tested on Comet Lake.
GitHub issue: https://github.com/thesofproject/linux/issues/1637
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing code will unconditionally return after dealing with the
first Slave on a link. This return should only happen when there is
an error case.
Tested on Comet Lake platform.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After a system suspend, the ALSA/ASoC core will invoke the .prepare()
callback and a TRIGGER_START when INFO_RESUME is not supported.
Likewise, when an underflow occurs, the .prepare callback will be invoked.
In both cases, the stream can be in DISABLED mode, and will transition
into the PREPARED mode. We however don't want the bus bandwidth to be
recomputed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We don't need to prepare the stream again if the stream is already
prepared.
sdw_prepare_stream() could be called multiple times without calling
sdw_deprepare_stream(). We call sdw_prepare_stream() in the prepare
dai ops and sdw_deprepare_stream() in the hw_free dai ops. If an xrun
happens, sdw_prepare_stream() will be called but
sdw_deprepare_stream() will not, which results in an imbalance and an
invalid total bandwidth.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The state machine and notes don't accurately explain or allow
transitions from STREAM_DEPREPARED and STREAM_DISABLED.
Add more explanations and allow for more transitions as a result of a
trigger_stop(), trigger_suspend() and prepare(), depending on the
ALSA/ASoC layer behavior defined by the INFO_RESUME and INFO_PAUSE
flags.
Also add basic checks to help debug inconsistent states and illegal
state machine transitions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200114235227.14502-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Somehow Intel folks were confused, the property is 2x what the mclk
frequency actually is (checked the actual bus frequency with a scope)
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113231129.19049-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the programming of the dev_number fails due to an IO error, a new
device_number will be assigned, resulting in a leak.
Make sure we only assign a device_number once per Slave device.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113225637.17313-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pierre-Louis Bossart