'ath10k_mac_tx' does not seems to use the per station table
entry pointer 'sta' (struct ieee80211_sta), hence remove passing
this unused argument
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The txpower is being recalculated when adding interface to make sure
txpower won't overshoot the spec, and when removing the interface,
the txpower should again to be recalculated to restore the correct value
from the active interface list.
Following is one of the scenario
vdev0 is created as STA and connected: txpower:23
vdev1 is created as P2P_DEVICE for control interface: txpower:0
vdev2 is created as p2p go/gc interface: txpower is 21
So the vdev2@txpower:21 will be set to firmware when vdev2 is created.
When we tear down the vdev2, the txpower needs to be recalculated to
re-set it to vdev0@txpower:23 as vdev0/vdev1 are the active interface.
ath10k_pci mac vdev 0 peer create 8c:fd:f0:01:62:98
ath10k_pci mac vdev_id 0 txpower 23
... (adding interface)
ath10k_pci mac vdev create 2 (add interface) type 1 subtype 3
ath10k_pci mac vdev_id 2 txpower 21
ath10k_pci mac txpower 21
... (removing interface)
ath10k_pci mac vdev 2 delete (remove interface)
ath10k_pci vdev 1 txpower 0
ath10k_pci vdev 0 txpower 23
ath10k_pci mac txpower 23
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever firmware crashes, and both CONFIG_ATH10K_DEBUGFS and
CONFIG_ALLOW_DEV_COREDUMP are enabled, dump information about the crash via a
devcoredump device. Dump can be read from userspace for further analysis from:
/sys/class/devcoredump/devcd*/data
As until now we have provided the firmware crash dump file via fw_crash_dump
debugfs keep it still available but deprecate and a warning print that the user
should switch to using dev_coredump.
Future improvement would be not to depend on CONFIG_ATH10K_DEBUGFS, as there
might be systems which want to get the firmware crash dump but not enable
debugfs. How to handle memory consumption is also something which needs to be
taken into account.
Signed-off-by: Arun Khandavalli <akhandav@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: rebase, fixes, improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align it with the cts protection call.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The cts protection vdev parameter, in new QCA9377 TF2.0 firmware,
requires bss peer to be created for the STATION vdev type.
bss peer is being allocated by the firmware after vdev_start/_up commands.
mac80211 may call the cts protection setup at any time, so the
we needs to track the situation and defer the cts configuration
to prevent firmware asserts, like below:
[00]: 0x05020001 0x000015B3 0x0099ACE2 0x00955B31
[04]: 0x0099ACE2 0x00060730 0x00000004 0x00000000
[08]: 0x0044C754 0x00412C10 0x00000000 0x00409C54
[12]: 0x00000009 0x00000000 0x00952F6C 0x00952F77
[16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
[20]: 0x4099ACE2 0x0040E858 0x00421254 0x004127F4
[24]: 0x8099B9B2 0x0040E8B8 0x00000000 0xC099ACE2
[28]: 0x800B75CB 0x0040E8F8 0x00000007 0x00005008
[32]: 0x809B048A 0x0040E958 0x00000010 0x00433B10
[36]: 0x809AFBBC 0x0040E9A8 0x0042BB74 0x0042BBBC
[40]: 0x8091D252 0x0040E9C8 0x0042BBBC 0x00000001
[44]: 0x809FFA45 0x0040EA78 0x0043D3E4 0x0042C2C8
[48]: 0x809FCEF4 0x0040EA98 0x0043D3E4 0x00000001
[52]: 0x80911210 0x0040EAE8 0x00000010 0x004041D0
[56]: 0x80911154 0x0040EB28 0x00400000 0x00000000
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The correct number for QCA9377 chip is 33 VDEVs.
This impacts also QCA6174 chip and it's max VDEV number.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.
This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_htt_tx_free_cont_txbuf' and 'ath10k_htt_tx_free_cont_frag_desc'
have NULL pointer checks to avoid crash if they are called twice
but this is as of now not sufficient as these pointers are not assigned
to NULL once the contiguous DMA memory allocation is freed, fix this.
Though this may not be hit with the explicity check of state variable
'tx_mem_allocated' check, good to have this addressed as well.
Below BUG_ON is hit when the above scenario is simulated
with kernel debugging enabled
page:f6d09a00 count:0 mapcount:-127 mapping: (null)
index:0x0
flags: 0x40000000()
page dumped because: VM_BUG_ON_PAGE(page_ref_count(page)
== 0)
------------[ cut here ]------------
kernel BUG at ./include/linux/mm.h:445!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP is at put_page_testzero.part.88+0xd/0xf
Call Trace:
[<c118a2cc>] __free_pages+0x3c/0x40
[<c118a30e>] free_pages+0x3e/0x50
[<c10222b4>] dma_generic_free_coherent+0x24/0x30
[<f8c1d9a8>] ath10k_htt_tx_free_cont_txbuf+0xf8/0x140
[<f8c1e2a9>] ath10k_htt_tx_destroy+0x29/0xa0
[<f8c143e0>] ath10k_core_destroy+0x60/0x80 [ath10k_core]
[<f8acd7e9>] ath10k_pci_remove+0x79/0xa0 [ath10k_pci]
[<c13ed7a8>] pci_device_remove+0x38/0xb0
[<c14d3492>] __device_release_driver+0x72/0x100
[<c14d36b7>] driver_detach+0x97/0xa0
[<c14d29c0>] bus_remove_driver+0x40/0x80
[<c14d427a>] driver_unregister+0x2a/0x60
[<c13ec768>] pci_unregister_driver+0x18/0x70
[<f8aced4f>] ath10k_pci_exit+0xd/0x2be [ath10k_pci]
[<c1101e78>] SyS_delete_module+0x158/0x210
[<c11b34f1>] ? __might_fault+0x41/0xa0
[<c11b353b>] ? __might_fault+0x8b/0xa0
[<c1001a4b>] do_fast_syscall_32+0x9b/0x1c0
[<c178da34>] sysenter_past_esp+0x45/0x74
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These are one-line functions that just call spin_lock/unlock_bh(); turn
them into static inlines to avoid the function call overhead.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reworks the ath9k driver to schedule transmissions to connected
stations in a way that enforces airtime fairness between them. It
accomplishes this by measuring the time spent transmitting to or
receiving from a station at TX and RX completion, and accounting this to
a per-station, per-QoS level airtime deficit. Then, an FQ-CoDel based
deficit scheduler is employed at packet dequeue time, to control which
station gets the next transmission opportunity.
Airtime fairness can significantly improve the efficiency of the network
when station rates vary. The following throughput values are from a
simple three-station test scenario, where two stations operate at the
highest HT20 rate, and one station at the lowest, and the scheduler is
employed at the access point:
Before / After
Fast station 1: 19.17 / 25.09 Mbps
Fast station 2: 19.83 / 25.21 Mbps
Slow station: 2.58 / 1.77 Mbps
Total: 41.58 / 52.07 Mbps
The benefit of airtime fairness goes up the more stations are present.
In a 30-station test with one station artificially limited to 1 Mbps,
we have seen aggregate throughput go from 2.14 to 17.76 Mbps.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ar9300_eeprom logic is already using only 8-bit (endian neutral),
__le16 and __le32 fields to state explicitly how the values should be
interpreted.
All other EEPROM implementations (4k, 9287 and def) were using u16 and
u32 fields with additional logic to swap the values (read from the
original EEPROM) so they match the current CPUs endianness.
The EEPROM format defaults to "all values are Little Endian", indicated
by the absence of the AR5416_EEPMISC_BIG_ENDIAN in the u8 EEPMISC
register. If we detect that the EEPROM indicates Big Endian mode
(AR5416_EEPMISC_BIG_ENDIAN is set in the EEPMISC register) then we'll
swap the values to convert them into Little Endian. This is done by
activating the EEPMISC based logic in ath9k_hw_nvram_swap_data even if
AH_NO_EEP_SWAP is set (this makes ath9k behave like the FreeBSD driver,
which also does not have a flag to enable swapping based on the
AR5416_EEPMISC_BIG_ENDIAN bit). Before this logic was only used to
enable swapping when "current CPU endianness != EEPROM endianness".
After changing all relevant fields to __le16 and __le32 sparse was used
to check that all code which reads any of these fields uses
le{16,32}_to_cpu.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are two ways of swapping the EEPROM data in the ath9k driver:
1) swab16 based on the first two EEPROM "magic" bytes (same for all
EEPROM formats)
2) field and EEPROM format specific swab16/swab32 (different for
eeprom_def, eeprom_4k and eeprom_9287)
The result of the first check was used to also enable the second swap.
This behavior seems incorrect, since the data may only be byte-swapped
(afterwards the data could be in the correct endianness).
Thus we introduce a separate check based on the "eepmisc" register
(which is part of the EEPROM data). When bit 0 is set, then the EEPROM
format specific values are in "big endian". This is also done by the
FreeBSD kernel, see [0] for example.
This allows us to parse EEPROMs with the "correct" magic bytes but
swapped EEPROM format specific values. These EEPROMs (mostly found in
lantiq and broadcom based big endian MIPS based devices) only worked
due to platform specific "hacks" which swapped the EEPROM so the
magic was inverted, which also enabled the format specific swapping.
With this patch the old behavior is still supported, but neither
recommended nor needed anymore.
[0]
50719b56d9/sys/dev/ath/ath_hal/ah_eeprom_9287.c (L351)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The AR5416_VER_MASK macro does the same as get_eeprom_rev, except that
one has to know the actual EEPROM type (and providing a reference to
that in a variable named "eep"). Additionally the eeprom_*.c
implementations used the same shifting logic multiple times to get the
eeprom revision which was also unnecessary duplication of
get_eeprom_rev.
Also use the AR5416_EEP_VER_MINOR_MASK macro where needed and introduce
a similar macro (AR5416_EEP_VER_MAJOR_MASK) for the major version.
Finally drop AR9287_EEP_VER_MINOR_MASK since it simply duplicates the
already defined AR5416_EEP_VER_MINOR_MASK.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
get_eeprom(ah, EEP_MINOR_REV) and get_eeprom_rev(ah) are both doing the
same thing: returning the EEPROM revision (12 lowest bits). Make the
code consistent by using get_eeprom_rev(ah) everywhere.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows deciding if we have to swap the EEPROM data (so it matches
the system's native endianness) even if no byte-swapping (swab16, based on
the first two bytes in the EEPROM) is needed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The eepMisc field was not set explicitly. The default value of 0 means
that the values in the EEPROM (template) should be interpreted as little
endian. However, this is not clear until comparing the AR9003 code with
the other EEPROM formats.
To make the code easier to understand we explicitly state that the values
are little endian - there are no functional changes with this patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This replaces a magic number with a named #define. Additionally it
removes two "eeprom format" specific #defines for the "big endianness"
bit which are the same on all eeprom formats.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver does not check if mapping dma memory succeed.
The patch adds the checks and failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYQGivAAoJEG4XJFUm622bqG0IAJtSGt4Fxv2jL7GPmPpEUtYK
F6G1PCk9LxO44rOZ15E/CT1vPk6Bnwqp9brdngmXwl7jc+jGs4MQN7g6cD4UZgPm
gxjx8cah2HPRVgEE7PeOILthRxwPA+9klycsvwtglkgQ1SpQVmLHDTLpeOAkRluY
olJGINoGHTD6osud6p3oKK+VP891omJvu8TPqRjhrhLhbQTWAuTxl2Gsdye30yag
CsdaEZb9wdUEBoS80EVRwvgBzqrdKU5kGDGbuzytcyrFrRHo4flti1KgxDg3nIpI
jC4Liwg0yE/aYZlfMqi/960rt8AttCJBDt/vwqp0mOE4IwFsE9Yaio6xXUonAC8=
=a6a/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.10. Major changes:
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
The H2C MEDIA_STATUS_RPT command for some reason causes 8192eu and
8723bu devices not being able to reconnect.
Reported-by: Barry Day <briselec@gmail.com>
Cc: <stable@vger.kernel.org> #4.8+
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop duplicate header vmalloc.h from ath5k/debug.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added new areas to fw_mappings area for UCODE code
and data areas.
The new areas are only exposed through debugfs blobs,
and mainly needed to access UCODE logs.
The change does not affect crash dumps because the
newly added areas overlap with the "upper" area which
is already dumped.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
num_descriptors and descriptor_size needs to be
checked for:
1) not being negative values
2) no overflow occurs when these are multiplied
together as done in wil_pmc_read.
An overflow of two signed integers is undefined
behavior.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently it was possible to call remain_on_channel(ROC)
while scan was active and this caused a crash in the FW.
In order to fix this problem and make the behavior
consistent with other drivers, queue the ROC in case
a scan is active and try it again when scan is done.
As part of the fix, clean up some locking issues and
return error if scan is called while ROC is active.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The usb_*_msg() functions expect a timeout in msecs but are given HZ,
which is ticks per second. If HZ=100, firmware download often times out
when there is modest USB utilization and the device fails to initialize.
Replaces HZ in usb_*_msg timeouts with 1000 msec since HZ is one second
for timeouts in jiffies.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare the structure ath_bus_ops as const as it is only passed as an
argument to the function ath9k_init_device. This argument is of type
const struct ath_bus_ops *, so ath_bus_ops structures with this property
can be declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ath_bus_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
expression e1,e2;
@@
ath9k_init_device(e1,e2,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ath_bus_ops i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ath_bus_ops i;
File size before:
text data bss dec hex filename
1295 232 0 1527 5f7 ath/ath9k/ahb.o
File size after:
text data bss dec hex filename
1359 176 0 1535 5ff ath/ath9k/ahb.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These memory chunks are often used as 'swap' by the NIC,
so it will be both reading and writing to these areas.
This seems to fix errors like this on my x86-64 machine:
kernel: DMAR: DMAR:[DMA Write] Request device [05:00.0] fault addr ff5de000
DMAR:[fault reason 05] PTE Write access is not set
Tested-by: Marek Behun <kabel@blackhole.sk>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With maximum number of vap's configured in a two radio supported
systems of ~256 Mb RAM, doing a continuous wifi down/up and
intermittent traffic streaming from the connected stations results
in failure to allocate contiguous memory for tx buffers. This results
in the disappearance of all VAP's and a manual reboot is needed as
this is not a crash (or) OOM(for OOM killer to be invoked). To address
this allocate contiguous memory for tx buffers one time and re-use them
until the modules are unloaded but this results in a slight increase in
memory footprint of ath10k when the wifi is down, but the modules are
still loaded. Also as of now we use a separate bool 'tx_mem_allocated'
to keep track of the one time memory allocation, as we cannot come up
with something like 'ath10k_tx_{register,unregister}' before
'ath10k_probe_fw' is called as 'ath10k_htt_tx_alloc_cont_frag_desc'
memory allocation is dependent on the hw_param 'continuous_frag_desc'
a) memory footprint of ath10k without the change
lsmod | grep ath10k
ath10k_core 414498 1 ath10k_pci
ath10k_pci 38236 0
b) memory footprint of ath10k with the change
ath10k_core 414980 1 ath10k_pci
ath10k_pci 38236 0
Memory Failure Call trace:
hostapd: page allocation failure: order:6, mode:0xd0
[<c021f150>] (__dma_alloc_buffer.isra.23) from
[<c021f23c>] (__alloc_remap_buffer.isra.26+0x14/0xb8)
[<c021f23c>] (__alloc_remap_buffer.isra.26) from
[<c021f664>] (__dma_alloc+0x224/0x2b8)
[<c021f664>] (__dma_alloc) from [<c021f810>]
(arm_dma_alloc+0x84/0x90)
[<c021f810>] (arm_dma_alloc) from [<bf954764>]
(ath10k_htt_tx_alloc+0xe0/0x2e4 [ath10k_core])
[<bf954764>] (ath10k_htt_tx_alloc [ath10k_core]) from
[<bf94e6ac>] (ath10k_core_start+0x538/0xcf8 [ath10k_core])
[<bf94e6ac>] (ath10k_core_start [ath10k_core]) from
[<bf947eec>] (ath10k_start+0xbc/0x56c [ath10k_core])
[<bf947eec>] (ath10k_start [ath10k_core]) from
[<bf8a7a04>] (drv_start+0x40/0x5c [mac80211])
[<bf8a7a04>] (drv_start [mac80211]) from [<bf8b7cf8>]
(ieee80211_do_open+0x170/0x82c [mac80211])
[<bf8b7cf8>] (ieee80211_do_open [mac80211]) from
[<c056afc8>] (__dev_open+0xa0/0xf4)
[21053.491752] Normal: 641*4kB (UEMR) 505*8kB (UEMR) 330*16kB (UEMR)
126*32kB (UEMR) 762*64kB (UEMR) 237*128kB (UEMR) 1*256kB (M) 0*512kB
0*1024kB 0*2048kB 0*4096kB = 95276kB
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During firmware crash (or) user requested manual restart
the system gets into a soft lock up state because of the
below root cause.
During user requested hardware restart / firmware crash
the system goes into a soft lockup state as 'napi_synchronize'
is called after 'napi_disable' (which sets 'NAPI_STATE_SCHED'
bit) and it sleeps into infinite loop as it waits for
'NAPI_STATE_SCHED' to be cleared. This condition is hit because
'ath10k_hif_stop' is called twice as below (resulting in calling
'napi_synchronize' after 'napi_disable')
'ath10k_core_restart' -> 'ath10k_hif_stop' (ATH10K_STATE_ON) ->
-> 'ieee80211_restart_hw' -> 'ath10k_start' -> 'ath10k_halt' ->
'ath10k_core_stop' -> 'ath10k_hif_stop' (ATH10K_STATE_RESTARTING)
Fix this by calling 'ath10k_halt' in ath10k_core_restart itself
as it makes more sense before informing mac80211 to restart h/w
Also remove 'ath10k_halt' in ath10k_start for the state of 'restarting'
Fixes: 3c97f5de1f ("ath10k: implement NAPI support")
Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a typo bug in the current implementation of
ath10k_wmi_tlv_op_gen_pdev_set_rd.
The conformance test limits are not set up properly.
The two arguments ctl2g and ctl5g were not used at all.
Instead, the regdomain arguments rd2g and rd5g were used
for the ctl settings as well.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Radar pulse and spectral scan reports are provided by the HW
with the ATH9K_RXERR_PHY flag set. Those are forwarded to
the dfs-detector and spectral module for further processing.
For some older chips, the pre-conditions checked in those
modules are ambiguous, since ATH9K_PHYERR_RADAR is used to
tag both types. As a result, spectral frames are fed into
the dfs-detector and vice versa.
This could lead to a false radar detection on a non-DFS
channel (which is uncritical), but more relevant it causes
useless CPU load for processing invalid frames.
This commit ensures that the dfs-detector and spectral
collector are only fed when they are active.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mwifiex
* properly terminate SSIDs so that uninitalised memory is not printed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYPZM9AAoJEG4XJFUm622bnTwH/j7KbWbTLE2H9abYJxne3sWQ
FOCrGNICgG9HYyLn33k7+dCBHGYa1f5qWO7dIeWhe6LEtXqrWBsxUFZbMrJVU7Te
sDr3s2364iIPhdLtYl5mM7M75Y2h2pt1XhpErmldCpFpnYad5vZEbIR1n96F3cz6
0ft6iUJpd3bf+KWxDUc707Vln42optvbcp7gjF+6mdShb0jlFkV9eOa85aJH6v38
5kKPhLfiv1Qs1sZXPrWc2oQUIc0LDY19sXtw/5DTLe4+r6ybsKlF1o4+b2yOVeiu
nrm1F/2D/829w3+4iYE63wACPGvyVaKYROtYgquyYkrI+6xyh1fmnout6SiwLe8=
=oEuI
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
mwifiex
* properly terminate SSIDs so that uninitalised memory is not printed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a5ffbe0a19 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Reported-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt7601u_mac_stop_hw should stop polling the rxq once it remains empty
but instead continues polling after the rxq status stays clear; bringing
down the interface takes about six seconds from this alone.
Speed up path by exiting rxq loop once status repeatedly polls empty.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Reviewed-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The scan results for scheduled scan as retrieved from the device
have changed. A field has been added which is not needed. However,
the appended info is. Luckily they are versioned so check that to
find out the location of the appended data.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can specify the interval for the scheduled scan. This
interval is found in scheduled scan plan. The driver supports only
one plan, which is legacy behaviour.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the .sched_scan_start() callback a condition was checked whether a
normal scan was ongoing. However, there is no need for this check as
it is ok to start the scheduled scan irrespective whether or not a
normal scan is ongoing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can provide list of channels in the schedule scan request.
This was ignored so all channels supported and allowed by the device
were used. This patch configures the device to use the channels as
listed in the request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework .sched_scan_start() callback moving actual configuration of
the device in pno source file.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmf_pno_config() function handles two configurations in
firmware. Split it and have caller sort out what is needed.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For scheduled scan we initiate an escan in firmware to obtain more
info missing from the scheduled scan notification we get from firmware.
For upcoming functionality this is also required so make it a bit
more generic.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mohammed Shafi Shajakhan