The qed_hsi.h is a huge header file containing HSI (Hardware Software
Interface) definitions of storm memory access, debug related, general
and management firmware specific. In order to have a better
code-organization HSI definition, this patch split the code across
multiple files, i.e.
- storm memory access HSI : qed_iro_hsi.h
- debug related HSI : qed_dbg_hsi.h
- Management firmware HSI : qed_mfg_hsi.h
- General HSI : qed_hsi.h
In addition, this patch also fixes existing checkpatch warnings and
few important checks.
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the actual copyright holder and years in all qed source files.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QLogic QED drivers source code is dual licensed under
GPL-2.0/BSD-3-Clause.
Remove all the boilerplates in the existing code and replace it with the
correct SPDX tag.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
25ms sleep cycles in waiting for PF response are excessive and may lead
to different timeout failures.
Start to wait with short udelays, and in most cases polling will end
here. If the time was not sufficient, switch to msleeps.
usleep_range() may go far beyond 100us depending on platform and tick
configuration, hence atomic udelays for consistency.
Also add explicit DMA barriers since 'done' always comes from a shared
request-response DMA pool, and note that in the comment nearby.
Fixes: 1408cc1fa4 ("qed: Introduce VFs")
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a DP_VERBOSE debug message. Fix it.
(Using American English spelling as this is the most common way
to spell this in the kernel).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs may hit VF-PF channel timeout while probing, as in some
cases it was observed that VF FLR and VF "acquire" message
transaction (i.e first message from VF to PF in VF's probe flow)
could occur simultaneously which could lead VF to fail sending
"acquire" message to PF as VF is marked disabled from HW perspective
due to FLR, which will result into channel timeout and VF probe failure.
In such cases, try retrying VF "acquire" message so that in later
attempts it could be successful to pass message to PF after the VF
FLR is completed and can be probed successfully.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the use of local PTT to propagate through the qed_mcp* API's.
Global ptt should not be used.
Register access should be done through layers. Register address is
mapped into a PTT, PF translation table. Several interface functions
require a PTT to direct read/write into register. There is a pool of
PTT maintained, and several PTT are used simultaneously to access
device registers in different flows. Same PTT should not be used in
flows that can run concurrently.
To avoid running out of PTT resources, too many PTT should not be
acquired without releasing them. Every PF has a global PTT, which is
used throughout the life of PF, in most important flows for register
access. Generic functions acquire the PTT locally and release after
the use. This patch aligns the use of Global PTT and Local PTT
accordingly.
Signed-off-by: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when a constant is used in a boolean context as it thinks a
bitwise operation may have been intended.
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!p_iov->b_pre_fp_hsi &&
^
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: use '&' for a
bitwise operation
if (!p_iov->b_pre_fp_hsi &&
^~
&
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: remove constant
to silence this warning
if (!p_iov->b_pre_fp_hsi &&
~^~
1 warning generated.
This has been here since commit 1fe614d10f ("qed: Relax VF firmware
requirements") and I am not entirely sure why since 0 isn't a special
case. Just remove the statement causing Clang to warn since it isn't
required.
Link: https://github.com/ClangBuiltLinux/linux/issues/126
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang complains when one enumerated type is implicitly converted to
another.
drivers/net/ethernet/qlogic/qed/qed_vf.c:686:6: warning: implicit
conversion from enumeration type 'enum qed_tunn_mode' to different
enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
QED_MODE_L2GENEVE_TUNN,
^~~~~~~~~~~~~~~~~~~~~~
Update mask's parameter to expect qed_tunn_mode, which is what was
intended.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW hsi contains 256 approximation buckets which are split in ramrod into
eight u32 values, but driver is using eight 'unsigned long' variables.
This patch fixes the mcast logic by making the API utilize u32.
Fixes: 83aeb933 ("qed*: Trivial modifications")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.
To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.
This request will be honored only for trusted VFs.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve the actual coalesce value from hardware for every Rx/Tx
queue, instead of Rx/Tx coalesce value cached during set coalesce.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The final addition on the qed front -
- VFs would now require their PFs to provide multiple CIDs
- Based on the availability of connections from PF, determine whether
XDP is feasible and share it with qede via dev_info.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently not mapping their doorbell bar, instead relying
on the small doorbell window they have in their limited regview bar.
In order to increase the number of possible Tx connections [queues]
employeed by VF past 16, we need to start using the doorbell bar if
one such is exposed - VF would communicate this fact to PF which would
return the size-bar internally configured into chip, according to
which the VF would decide whether to actually utilize the doorbell
bar.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the infrastructure for supporting VFs that want to open
multiple transmission queues on the same queue-zone.
At this point, there are no VFs that actually request this functionality,
but later patches would remedy that.
a. VF and PF would communicate the capability during ACQUIRE;
Legacy VFs would continue on behaving as they do today
b. PF would communicate number of supported CIDs to the VF
and would enforce said limitation
c. Whenever VF passes a request for a given queue configuration
it would also pass an associated index within said queue-zone
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of an effort of a cleaner seperation between qed and the protocol
drivers, the L2 interface is to use the SB structure for initialization
purposes opaquely.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step in allowing a single PF/VF to open multiple queues on
the same queue zone is to add per-hwfn database of queue-cids
as a two-dimensional array where entry would be according to
[queue zone][internal index].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PF today holds 2 different arrays - one holding information
about the HW configuration and one holding information about
the SBs that are used by the protocol drivers.
These arrays aren't really connected - e.g., protocol driver
initializing a given SB would not mark the same SB as occupied
in the HW shadow array.
Move into a single array [at least for PFs] - hold the mapping
of the driver-protocol SBs on the HW entry which they configure.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that we're holding a mutex on this error
path. Let's goto exit instead of returning directly.
Fixes: b0bccb69eb ("qed: Change locking scheme for VF channel")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware channel APIs support between
VF and PF for tunnelling configuration for the VFs.
According to that configuration VFs can run VXLAN/GENEVE/GRE
tunnels over it with tunnel features offloaded.
Using these APIs VF can also request for UDP ports configuration
to the PF, although PF and it's child VFs share the same port.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently logging errors when communicating
with their PFs in a too-low verbosity that wouldn't
be shown by default. As timeouts and failed commands
are crucial for VF operability, make them appear by
default.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.
This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.
Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A step toward having qede agnostic to the queue configurations
in firmware/hardware - let the RSS indirections use queue handles
instead of actual queue indices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.
This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.
This patch re-organizes the way L2 queues are configured and maintained.
In short:
- Required parameters for queue init are now well-defined.
- Qed would allocate a queue-cid based on parameters.
Upon initialization success, it would return a handle to caller.
- Queue-handle would be maintained by entity requesting queue-init,
not necessarily qed.
- All further queue-APIs [update, destroy] would use the opaque
handle as reference for the queue instead of various indices.
The possible owners of such handles:
- PF queues [qede] - complete handles based on provided configuration.
- VF queues [qede] - fw-context-less handles, containing only relative
information; Only the PF-side would need the absolute indices
for configuration, so they're omitted here.
- VF queues [qed, PF-side] - complete handles based on VF initialization.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When relaxing the limitation on the number of unicast MAC filters
an interface can configure, qed started passing the MAC quota to
qede. However, the value is initialized only for PFs, causing VFs
to always try and configure themselves as promiscuous
[as they believe they lack the resources to configure the rx-mode].
Fixes: 7b7e70f979 ("qed*: Allow unicast filtering")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hypervisors can support MAC hints to their VFs.
Even though we don't have such a hypervisor API in linux, we add
sufficient logic for the VF to be able to receive such hints and
set the mac accordingly - as long as the VF has not been set with
a MAC already.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the qedr driver - FW notification, resource
initializations, etc.
Signed-off-by: Ram Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a few warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_l2.c:112:5: warning: no previous prototype for 'qed_sp_vport_start' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:110:6: warning: no previous prototype for 'qed_iov_is_valid_vfid' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:188:5: warning: no previous prototype for 'qed_iov_post_vf_bulletin' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:578:6: warning: no previous prototype for 'qed_iov_set_vfs_to_disable' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:1135:28: warning: no previous prototype for 'qed_iov_get_public_vf_info' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:1148:6: warning: no previous prototype for 'qed_iov_clean_vf' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:2444:5: warning: no previous prototype for 'qed_iov_chk_ucast' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:2762:5: warning: no previous prototype for 'qed_iov_vf_flr_cleanup' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages are unnecessary as OOM allocation failures already do
a dump_stack() giving more or less the same information.
$ size drivers/net/ethernet/qlogic/qed/built-in.o* (defconfig x86-64)
text data bss dec hex filename
127817 27969 32800 188586 2e0aa drivers/net/ethernet/qlogic/qed/built-in.o.new
132474 27969 32800 193243 2f2db drivers/net/ethernet/qlogic/qed/built-in.o.old
Miscellanea:
o Change allocs to the generally preferred forms where possible.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each VF employees a lock that's supposed to serialize its usage of the
HW channel for communication with its PF, but the critical section is
ill-defined:
- VFs currently release the lock whenever the PF response arrives,
prior to actually processing the reply buffer [which was also supposed
to have been protected by same lock].
- The lock would be released on first response, ignoring the possibilty
the sw flow isn't over [as might be the case of the acquisition flow].
As a result, the flow would run unprotected and would cause a double
mutex release [as the additional message completion would release it
while its actually already free].
Change the flow to have a dedicated function to be called at end of each
flow and release the lock.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern VFs can't run on old non-compatible as the fastpath HSI is
slightly changed - but as the HSI is actually very close [basically,
a single bit whose meaning flipped] this can be supported with small
modifications.
The major differences would be in:
- Recognizing that VF is running on top of a legacy PF.
- Returning some slowpath configurations that are no longer needed
on top of modern PFs, but would be required when working over
the legacy ones.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before requesting the firmware to start Rx queues,
driver goes and sets the queue producer in the device to 0.
But while the producer is 32-bit, the driver currently clears 64 bits,
effectively zeroing an additional CID's producer as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, the VF is aware of its queues context-ids, and calculates the
doorbell address when opening its queues on its own.
The configuration of doorbells in HW can sometime in the future be changed
by the PF [hw has several configurable features that might affect doorbell
addresses, e.g., dpm support], this would break compatibility with older
VFs as their calculated doorbell addresses would be incorrect for such a
configuration.
In order to avoid such a backward compatibility failure, let the PF make
the calculation of the doorbell offset based on the context-id, and pass
that to the VF.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the goals of the vf's first message to the PF [acquire]
is to learn about the number of resources available to it [macs, vlans,
etc.]. This is done via negotiation - the VF requires a set of resources,
which the PF either approves or disaproves and sends a smaller set of
resources as alternative. In this later case, the VF is then expected to
either abort the probe or re-send the acquire message with less
required resources.
While this infrastructure exists since the initial submision of qed
SRIOV support, it's in fact completely inoperational - PF isn't really
looking into the resources the VF has asked for and is never going to
reply to the VF that it lacks resources.
This patch addresses this flow, fixing it and allowing the PF and VF
to actually agree on a set of resources.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver require an exact match between VF and PF storm firmware;
Any difference would fail the VF acquire message, causing the VF probe
to be aborted.
While there's still dependencies between the two, the recent FW submission
has relaxed the match requirement - instead of an exact match, there's now
a 'fastpath' HSI major/minor scheme, where VFs and PFs that match in their
major number can co-exist even if their minor is different.
In order to accomadate this change some changes in the vf-start init flow
had to be made, as the VF start ramrod now has to be sent only after PF
learns which fastpath HSI its VF is requiring.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.
While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.
1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
<vid> and tags all outgoing traffic sent by VF with <vid>.
2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.
This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.
It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.
This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]
Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds sufficient changes to allow VFs l2-configuration flows to work.
While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Omkar Kulkarni