KVM sometimes flushes host TLB entries, reading each one to check if it
corresponds to a guest KSeg0 address. In the absence of EntryHi.EHInv
bits to invalidate the whole entry, the entries will be set to unique
virtual addresses in KSeg0 (which is not TLB mapped), spaced 2*PAGE_SIZE
apart.
The TLB read however will clobber the CP0_PageMask register with
whatever page size that TLB entry had, and that same page size will be
written back into the TLB entry along with the unique address.
This would cause breakage when transparent huge pages are enabled on
64-bit host kernels, since huge page entries will overlap other nearby
entries when separated by only 2*PAGE_SIZE, causing a machine check
exception.
Fix this by restoring the old CP0_PageMask value (which should be set to
the normal page size) after reading the TLB entry if we're going to go
ahead and invalidate it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_mips_trans_replace() passes a pointer to KVM_GUEST_KSEGX(). This
breaks on 64-bit builds due to the cast of that 64-bit pointer to a
different sized 32-bit int. Cast the pointer argument to an unsigned
long to work around the warning.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When emulating MFC0 instructions to load 32-bit values from guest COP0
registers and the RDHWR instruction to read the CC (Count) register,
sign extend the result to comply with the MIPS64 architecture. The
result must be in canonical 32-bit form or the guest may malfunction.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MFC0 and MTC0 instructions in the guest which cause traps can be
replaced with 32-bit loads and stores to the commpage, however on big
endian 64-bit builds the offset needs to have 4 added so as to
load/store the least significant half of the long instead of the most
significant half.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fail if the address of the allocated exception base doesn't fit into the
CP0_EBase register. This can happen on MIPS64 if CP0_EBase.WG isn't
implemented but RAM is available outside of the range of KSeg0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the KVM entry point to write CP0_EBase as a 64-bit register when
it is 64-bits wide, and to set the WG (write gate) bit if it exists in
order to write bits 63:30 (or 31:30 on MIPS32).
Prior to MIPS64r6 it was UNDEFINED to perform a 64-bit read or write of
a 32-bit COP0 register. Since this is dynamically generated code,
generate the right type of access depending on whether the kernel is
64-bit and cpu_has_ebase_wg.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the KVM entry code to set the CP0_Entry.KX bit on 64-bit kernels.
This is important to allow the entry code, running in kernel mode, to
access the full 64-bit address space right up to the point of entering
the guest, and immediately after exiting the guest, so it can safely
restore & save the guest context from 64-bit segments.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MIPS KVM entry code (originally kvm_locore.S, later locore.S, and
now entry.c) has never quite been right when built for 64-bit, using
32-bit instructions when 64-bit instructions were needed for handling
64-bit registers and pointers. Fix several cases of this now.
The changes roughly fall into the following categories.
- COP0 scratch registers contain guest register values and the VCPU
pointer, and are themselves full width. Similarly CP0_EPC and
CP0_BadVAddr registers are full width (even though technically we
don't support 64-bit guest address spaces with trap & emulate KVM).
Use MFC0/MTC0 for accessing them.
- Handling of stack pointers and the VCPU pointer must match the pointer
size of the kernel ABI (always o32 or n64), so use ADDIU.
- The CPU number in thread_info, and the guest_{user,kernel}_asid arrays
in kvm_vcpu_arch are all 32 bit integers, so use lw (instead of LW) to
load them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are several unportable uses of CKSEG0ADDR() in MIPS KVM, which
implicitly assume that a host physical address will be in the low 512MB
of the physical address space (accessible in KSeg0). These assumptions
don't hold for highmem or on 64-bit kernels.
When interpreting the guest physical address when reading or overwriting
a trapping instruction, use kmap_atomic() to get a usable virtual
address to access guest memory, which is portable to 64-bit and highmem
kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Calculate the PFN of the commpage using virt_to_phys() instead of
CPHYSADDR(). This is more portable as kzalloc() may allocate from XKPhys
instead of KSeg0 on 64-bit kernels, which CPHYSADDR() doesn't handle.
This is sufficient for highmem kernels too since kzalloc() will allocate
from lowmem in KSeg0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KSEGX() macro is defined to 32-bit sign extend the address argument
and logically AND the result with 0xe0000000, with the final result
usually compared against one of the CKSEG macros. However the literal
0xe0000000 is unsigned as the high bit is set, and is therefore
zero-extended on 64-bit kernels, resulting in the sign extension bits of
the argument being masked to zero. This results in the odd situation
where:
KSEGX(CKSEG) != CKSEG
(0xffffffff80000000 & 0x00000000e0000000) != 0xffffffff80000000)
Fix this by 32-bit sign extending the 0xe0000000 literal using
_ACAST32_.
This will help some MIPS KVM code handling 32-bit guest addresses to
work on 64-bit host kernels, but will also affect KSEGX in
dec_kn01_be_backend() on a 64-bit DECstation kernel, and the SiByte DMA
page ops KSEGX check in clear_page() and copy_page() on 64-bit SB1
kernels, neither of which appear to be designed with 64-bit segments in
mind anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Kexec needs to know the addresses of all VMCSs that are active on
each CPU, so that it can flush them from the VMCS caches. It is
safe to record superfluous addresses that are not associated with
an active VMCS, but it is not safe to omit an address associated
with an active VMCS.
After a call to vmcs_load, the VMCS that was loaded is active on
the CPU. The VMCS should be added to the CPU's list of active
VMCSs before it is loaded.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
KVM maintains L1's current VMCS in guest memory, at the guest physical
page identified by the argument to VMPTRLD. This makes hairy
time-of-check to time-of-use bugs possible,as VCPUs can be writing
the the VMCS page in memory while KVM is emulating VMLAUNCH and
VMRESUME.
The spec documents that writing to the VMCS page while it is loaded is
"undefined". Therefore it is reasonable to load the entire VMCS into
an internal cache during VMPTRLD and ignore writes to the VMCS page
-- the guest should be using VMREAD and VMWRITE to access the current
VMCS.
To adhere to the spec, KVM should flush the current VMCS during VMPTRLD,
and the target VMCS during VMCLEAR (as given by the operand to VMCLEAR).
Since this implementation of VMCS caching only maintains the the current
VMCS, VMCLEAR will only do a flush if the operand to VMCLEAR is the
current VMCS pointer.
KVM will also flush during VMXOFF, which is not mandated by the spec,
but also not in conflict with the spec.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It turns out that if the guest does a H_CEDE while the CPU is in
a transactional state, and the H_CEDE does a nap, and the nap
loses the architected state of the CPU (which is is allowed to do),
then we lose the checkpointed state of the virtual CPU. In addition,
the transactional-memory state recorded in the MSR gets reset back
to non-transactional, and when we try to return to the guest, we take
a TM bad thing type of program interrupt because we are trying to
transition from non-transactional to transactional with a hrfid
instruction, which is not permitted.
The result of the program interrupt occurring at that point is that
the host CPU will hang in an infinite loop with interrupts disabled.
Thus this is a denial of service vulnerability in the host which can
be triggered by any guest (and depending on the guest kernel, it can
potentially triggered by unprivileged userspace in the guest).
This vulnerability has been assigned the ID CVE-2016-5412.
To fix this, we save the TM state before napping and restore it
on exit from the nap, when handling a H_CEDE in real mode. The
case where H_CEDE exits to host virtual mode is already OK (as are
other hcalls which exit to host virtual mode) because the exit
path saves the TM state.
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This moves the transactional memory state save and restore sequences
out of the guest entry/exit paths into separate procedures. This is
so that these sequences can be used in going into and out of nap
in a subsequent patch.
The only code changes here are (a) saving and restore LR on the
stack, since these new procedures get called with a bl instruction,
(b) explicitly saving r1 into the PACA instead of assuming that
HSTATE_HOST_R1(r13) is already set, and (c) removing an unnecessary
and redundant setting of MSR[TM] that should have been removed by
commit 9d4d0bdd9e0a ("KVM: PPC: Book3S HV: Add transactional memory
support", 2013-09-24) but wasn't.
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
- GICv3 ITS emulation
- Simpler idmap management that fixes potential TLB conflicts
- Honor the kernel protection in HYP mode
- Removal of the old vgic implementation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Del
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into next
KVM/ARM changes for Linux 4.8
- GICv3 ITS emulation
- Simpler idmap management that fixes potential TLB conflicts
- Honor the kernel protection in HYP mode
- Removal of the old vgic implementation
Now that all ITS emulation functionality is in place, we advertise
MSI functionality to userland and also the ITS device to the guest - if
userland has configured that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce a new KVM device that represents an ARM Interrupt Translation
Service (ITS) controller. Since there can be multiple of this per guest,
we can't piggy back on the existing GICv3 distributor device, but create
a new type of KVM device.
On the KVM_CREATE_DEVICE ioctl we allocate and initialize the ITS data
structure and store the pointer in the kvm_device data.
Upon an explicit init ioctl from userland (after having setup the MMIO
address) we register the handlers with the kvm_io_bus framework.
Any reference to an ITS thus has to go via this interface.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
KVM capabilities can be a per-VM property, though ARM/ARM64 currently
does not pass on the VM pointer to the architecture specific
capability handlers.
Add a "struct kvm*" parameter to those function to later allow proper
per-VM capability reporting.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We don't emulate ptff subfunctions, therefore react on any attempt of
execution by setting cc=3 (Requested function not available).
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We will use illegal instruction 0x0000 for handling 2 byte sw breakpoints
from user space. As it can be enabled dynamically via a capability,
let's move setting of ICTL_OPEREXC to the post creation step, so we avoid
any races when enabling that capability just while adding new cpus.
Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
My static checker complains that this condition looks like it should be
== instead of =. This isn't a fast path, so we don't need to be fancy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
kzalloc was replaced with kvm_kvzalloc to allow non-contiguous areas and
rcu had to be modified to cope with it.
The practical limit for KVM_MAX_VCPU_ID right now is INT_MAX, but lower
value was chosen in case there were bugs. 1023 is sufficient maximum
APIC ID for 288 VCPUs.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
288 is in high demand because of Knights Landing CPU.
We cannot set the limit to 640k, because that would be wasting space.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add KVM_X2APIC_API_DISABLE_BROADCAST_QUIRK as a feature flag to
KVM_CAP_X2APIC_API.
The quirk made KVM interpret 0xff as a broadcast even in x2APIC mode.
The enableable capability is needed in order to support standard x2APIC and
remain backward compatible.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Expand kvm_apic_mda comment. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_CAP_X2APIC_API is a capability for features related to x2APIC
enablement. KVM_X2APIC_API_32BIT_FORMAT feature can be enabled to
extend APIC ID in get/set ioctl and MSI addresses to 32 bits.
Both are needed to support x2APIC.
The feature has to be enableable and disabled by default, because
get/set ioctl shifted and truncated APIC ID to 8 bits by using a
non-standard protocol inspired by xAPIC and the change is not
backward-compatible.
Changes to MSI addresses follow the format used by interrupt remapping
unit. The upper address word, that used to be 0, contains upper 24 bits
of the LAPIC address in its upper 24 bits. Lower 8 bits are reserved as
0. Using the upper address word is not backward-compatible either as we
didn't check that userspace zeroed the word. Reserved bits are still
not explicitly checked, but non-zero data will affect LAPIC addresses,
which will cause a bug.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
LAPIC is reset in xAPIC mode and the surrounding code expects that.
KVM never resets after initialization. This patch is just for sanity.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The register is in hardware-compatible format now, so there is not need
to intercept.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
APIC ID should be set to the initial APIC ID when enabling LAPIC.
This only matters if the guest changes APIC ID. No sane OS does that.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We currently always shift APIC ID as if APIC was in xAPIC mode.
x2APIC mode wants to use more bits and storing a hardware-compabible
value is the the sanest option.
KVM API to set the lapic expects that bottom 8 bits of APIC ID are in
top 8 bits of APIC_ID register, so the register needs to be shifted in
x2APIC mode.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x2APIC supports up to 2^32-1 LAPICs, but most guest in coming years will
probably has fewer VCPUs. Dynamic size saves memory at the cost of
turning one constant into a variable.
apic_map mutex had to be moved before allocation to avoid races with cpu
hotplug.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Logical x2APIC IDs map injectively to physical x2APIC IDs, so we can
reuse the physical array for them. This allows us to save space by
sizing the logical maps according to the needs of xAPIC.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_irq_delivery_to_apic_fast and kvm_intr_is_single_vcpu_fast both
compute the interrupt destination. Factor the code.
'struct kvm_lapic **dst = NULL' had to be added to silence GCC.
GCC might complain about potential NULL access in the future, because it
missed conditions that avoided uninitialized uses of dst.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
240 has been well tested by Red Hat.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MMU now knows about execute only mappings, so
advertise the feature to L1 hypervisors
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To support execute only mappings on behalf of L1 hypervisors,
reuse ACC_USER_MASK to signify if the L1 hypervisor has the R bit
set.
For the nested EPT case, we assumed that the U bit was always set
since there was no equivalent in EPT page tables. Strictly
speaking, this was not necessary because handle_ept_violation
never set PFERR_USER_MASK in the error code (uf=0 in the
parlance of update_permission_bitmask). We now have to set
both U and UF correctly, respectively in FNAME(gpte_access)
and in handle_ept_violation.
Also in handle_ept_violation bit 3 of the exit qualification is
not enough to detect a present PTE; all three bits 3-5 have to
be checked.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To support execute only mappings on behalf of L1
hypervisors, we need to teach set_spte() to honor all three of
L1's XWR bits. As a start, add a new variable "shadow_present_mask"
that will be set for non-EPT shadow paging and clear for EPT.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have two versions of the above function.
To prevent confusion and bugs in the future, remove
the non-FNAME version entirely and replace all calls
with the actual check.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is safe because this function is called
on host controlled page table and non-present/non-MMIO
sptes never use bits 1..31. For the EPT case, this
ensures that cases where only the execute bit is set
is marked valid.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no reason to read the entry/exit control fields of the
VMCS and immediately write back the same value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because the vmcs12 preemption timer is emulated through a separate hrtimer,
we can keep on using the preemption timer in the vmcs02 to emulare L1's
TSC deadline timer.
However, the corresponding bit in the pin-based execution control field
must be kept consistent between vmcs01 and vmcs02. On vmentry we copy
it into the vmcs02; on vmexit the preemption timer must be disabled in
the vmcs01 if a preemption timer vmexit happened while in guest mode.
The preemption timer value in the vmcs02 is set by vmx_vcpu_run, so it
need not be considered in prepare_vmcs02.
Cc: Yunhong Jiang <yunhong.jiang@intel.com>
Cc: Haozhong Zhang <haozhong.zhang@intel.com>
Tested-by: Wanpeng Li <kernellwp@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The preemption timer for nested VMX is emulated by hrtimer which is started on L2
entry, stopped on L2 exit and evaluated via the check_nested_events hook. However,
nested_vmx_exit_handled is always returning true for preemption timer vmexit. Then,
the L1 preemption timer vmexit is captured and be treated as a L2 preemption
timer vmexit, causing NULL pointer dereferences or worse in the L1 guest's
vmexit handler:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [< (null)>] (null)
PGD 0
Oops: 0010 [#1] SMP
Call Trace:
? kvm_lapic_expired_hv_timer+0x47/0x90 [kvm]
handle_preemption_timer+0xe/0x20 [kvm_intel]
vmx_handle_exit+0x169/0x15a0 [kvm_intel]
? kvm_arch_vcpu_ioctl_run+0xd5d/0x19d0 [kvm]
kvm_arch_vcpu_ioctl_run+0xdee/0x19d0 [kvm]
? kvm_arch_vcpu_ioctl_run+0xd5d/0x19d0 [kvm]
? vcpu_load+0x1c/0x60 [kvm]
? kvm_arch_vcpu_load+0x57/0x260 [kvm]
kvm_vcpu_ioctl+0x2d3/0x7c0 [kvm]
do_vfs_ioctl+0x96/0x6a0
? __fget_light+0x2a/0x90
SyS_ioctl+0x79/0x90
do_syscall_64+0x68/0x180
entry_SYSCALL64_slow_path+0x25/0x25
Code: Bad RIP value.
RIP [< (null)>] (null)
RSP <ffff8800b5263c48>
CR2: 0000000000000000
---[ end trace 9c70c48b1a2bc66e ]---
This can be reproduced readily by preemption timer enabled on L0 and disabled
on L1.
Return false since preemption timer vmexits must never be reflected to L2.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Yunhong Jiang <yunhong.jiang@intel.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Simplify cpu_has_vmx_preemption_timer. This is consistent with the
rest of setup_vmcs_config and preparatory for the next patch.
Tested-by: Wanpeng Li <kernellwp@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Default the guest PRId register to represent a generic QEMU machine
instead of a 24kc on MIPSr6. 24kc isn't supported by r6 Linux kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When KVM emulates the RDHWR instruction, decode the instruction more
strictly. The rs field (bits 25:21) should be zero, as should bits 10:9.
Bits 8:6 is the register select field in MIPSr6, so we aren't strict
about those bits (no other operations should use that encoding space).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Recognise the new MIPSr6 CACHE instruction encoding rather than the
pre-r6 one when an r6 kernel is being built. A SPECIAL3 opcode is used
and the immediate field is reduced to 9 bits wide since MIPSr6.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support in KVM for emulation of instructions in the forbidden slot
of MIPSr6 compact branches. If we hit an exception on the forbidden
slot, then the branch must not have been taken, which makes calculation
of the resume PC trivial.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
James Hogan