Since we enable APD and DLL/RXC/TXC disable we need to use
bcm54xx_suspend() in order not to do a read/modify/write of the BMCR
register which is incompatible with the desired settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two Ethernet PHYs support IDDQ-SR therefore wire-up the suspend
and resume callbacks to point to bcm54xx_suspend() and bcm54xx_resume().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for putting the PHY into IDDQ Soft Recovery mode by setting
the TOP_MISC register bits accordingly. This requires us to implement a
custom bcm54xx_suspend() routine which diverges from genphy_suspend() in
order to configure the PHY to enter IDDQ with software recovery as well
as avoid doing a read/modify/write on the BMCR register.
Doing a read/modify/write on the BMCR register means that the
auto-negotation bit may remain which interferes with the ability to put
the PHY into IDDQ-SR mode. We do software reset upon suspend in order to
put the PHY back into its state prior to suspend as recommended by the
datasheet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the DAC early wake when then link operates at 10BaseT allows
power savings in the hundreds of milli Watts by shutting down the
transmitter. A number of errata have been issued for various Gigabit
PHYs and the recommendation is to enable both the early and forced DAC
wake to be on the safe side. This needs to be done dynamically based
upon the link state, which is why a link_change_notify callback is
utilized.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210916212742.1653088-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Restore PHY_ID_BCM54811 accidently removed by commit 5d4358ede8.
Fixes: 5d4358ede8 ("net: phy: broadcom: Allow BCM54210E to configure APD")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Gigabit PHYs use the same register layout as far as fetching
statistics goes. Fast Ethernet PHYs do not all support statistics, and
the BCM54616S would require some switching between the coper and fiber
modes to fetch the appropriate statistics which is not supported yet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY driver entry for BCM50160 and BCM50610M calls
bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in
order to configuration appropriate clock delays on the PHY, fix that.
Fixes: 733336262b ("net: phy: Allow BCM5481x PHYs to setup internal TX/RX clock delay")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the datasheet, when we clear the power down bit, the PHY remains in
an internal reset state for 40us and then resume normal operation.
Account for that delay to avoid any issues in the future if
genphy_resume() changes.
Fixes: fe26821fa6 ("net: phy: broadcom: Wire suspend/resume for BCM54810")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm54xx_config_init was modifying the PHY LED configuration to enable link
and activity indications. However, some SFP modules (such as Bel-Fuse
SFP-1GBT-06) have no LEDs but use the LED outputs to control the SFP LOS
signal, and modifying the LED settings will cause the LOS output to
malfunction. Skip this configuration for PHYs which are bound to an SFP
bus.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54210E/BCM50212E has been verified to work correctly with the
auto-power down configuration done by bcm54xx_adjust_rxrefclk(), add it
to the list of PHYs working.
While we are at it, provide an appropriate name for the bit we are
changing which disables the RXC and TXC during auto-power down when
there is no energy on the cable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of unused flags defined today and since we are scarce
on space and may need to introduce new flags in the future remove and
shift every existing flag down into a contiguous assignment.
PHY_BCM_FLAGS_MODE_1000BX was only used internally for the BCM54616S
PHY, so we allocate a driver private structure instead to store that
flag instead of canibalizing one from phydev->dev_flags for that
purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a forward declaration by moving the callers of
bcm54xx_config_clock_delay() below its body.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is nowhere used in the kernel. It also seems to be lacking the
proper fiber advertise flags. Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Michael Walle <michael@walle.cc>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch makes checkpatch happy for tabs
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54811 PHY shares many similarities with the already supported BCM54810
PHY but additionally requires some semi-unique configuration.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM53125 has internal Gigabit PHYs which support interrupts as well as
statistics, make it possible to configure both of those features with a
PHY driver entry.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54810 PHY can use the standard BMCR Power down suspend, but needs
a custom resume routine which first clear the Power down bit, and then
re-initializes the PHY. While in low-power mode, the PHY only accepts
writes to the BMCR register. The datasheet clearly says it:
Reads or writes to any MII register other than MII Control register
(address 00h) while the device is in the standby power-down mode may
cause unpredictable results.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm54xx_adjust_rxrefclk() already checks for PHY_BRCM_AUTO_PWRDWN_ENABLE
and PHY_BRCM_DIS_TXCRXC_NOENRGY in order to set the appropriate bit. The
situation is a bit more complicated with the flag
PHY_BRCM_RX_REFCLK_UNUSED but essentially amounts to the same situation.
The default setting for the 125MHz clock is to be on for all PHYs and
we still treat BCM50610 and BCM50610M specifically with the polarity of
the bit reversed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function bcm54xx_adjust_rxrefclk() works correctly on the BCM54810
PHY, allow this device ID to proceed through.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54616S PHY cannot work properly in RGMII->1000Base-X mode, mainly
because genphy functions are designed for copper links, and 1000Base-X
(clause 37) auto negotiation needs to be handled differently.
This patch enables 1000Base-X support for BCM54616S by customizing 3
driver callbacks, and it's verified to be working on Facebook CMM BMC
platform (RGMII->1000Base-KX):
- probe: probe callback detects PHY's operation mode based on
INTERF_SEL[1:0] pins and 1000X/100FX selection bit in SerDES 100-FX
Control register.
- config_aneg: calls genphy_c37_config_aneg when the PHY is running in
1000Base-X mode; otherwise, genphy_config_aneg will be called.
- read_status: calls genphy_c37_read_status when the PHY is running in
1000Base-X mode; otherwise, genphy_read_status will be called.
Note: BCM54616S PHY can also be configured in RGMII->100Base-FX mode, and
100Base-FX support is not available as of now.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm54612e_config_init() duplicates what bcm54xx_config_clock_delay()
does with respect to configuring RGMII TX/RX delays appropriately.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0fc9ae1076 ("net: phy: broadcom: add support for
BCM54210E") added support for BCM54210E but also unconditionally cleared
the RXC to RXD skew and the TXD to TXC skew, thus only making
PHY_INTERFACE_MODE_RGMII a possible configuration. Use
bcm54xx_config_clock_delay() which correctly sets the registers
depending on the 4 possible PHY interface values that exist for RGMII.
Fixes: 0fc9ae1076 ("net: phy: broadcom: add support for BCM54210E")
Reported-by: Manasa Mudireddy <manasa.mudireddy@broadcom.com>
Reported-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This puts the quad PHY ports in power-down mode when the PHY transitions
to the PHY_HALTED state. It is likely that all the other PHYs support
the BMCR_PDOWN bit, but I only have the BCM5464R to test.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows users to enable/disable internal TX and/or RX clock
delay for BCM54616S PHYs so as to satisfy RGMII timing specifications.
On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.
The patch is inspired by commit 733336262b ("net: phy: Allow BCM5481x
PHYs to setup internal TX/RX clock delay").
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54612E have 4 multi-functional LED pins that can be configured
through register setting; the LED4 pin can be configured to a 125MHz
reference clock output by setting the spare register. Since the dedicated
CLK125 reference clock pin is not brought out on the 48-Pin MLP, the LED4
pin is the only pin to provide such function in this package, and therefore
it is beneficial to just enable the reference clock by default.
Signed-off-by: Kun Yi <kunyi@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It adds support for BCM89610 (Single-Port 10/100/1000BASE-T)
transceiver which is used in P3310 Tegra186 platform.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for the builtin PHYs present in the Broadcom BCM5395 switch. This
allows us to retrieve the PHY statistics among other things.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch mistakenly removed three chip-specific config settings.
Add them again.
Fixes: 80274abafc "net: phy: remove generic settings for callbacks config_aneg and read_status from drivers"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.
So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LMhttp://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.
This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fa8cddaf90 ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows users to enable/disable internal TX and/or RX
clock delay for BCM5481x series PHYs so as to satisfy RGMII timing
specifications.
On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extra BCM54612E code in PHY driver isn't really aneg specific. Even
without it aneg works OK but the problem is no packets pass through PHY.
Moreover putting this code inside config_aneg callback didn't allow
resuming PHY correctly. When driver called phy_stop and phy_start it was
putting PHY machine into RESUMING state. After that machine was
switching into AN and NOLINK without ever calling phy_start_aneg. This
prevented this extra setup from being called and PHY didn't work.
This change has been verified to fix network on BCM47186B0 SoC device
with BCM54612E.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling delay skew and GTXCLK
bits.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had two defines for the same bit (both were used with the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC register).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 5b4e290051 ("net: phy: broadcom: add
bcm54xx_auxctl_read") we have a reading helper so use it and avoid code
duplication.
It also means we don't need MII_BCM54XX_AUXCTL_SHDWSEL_MISC define as
it's the same as MII_BCM54XX_AUXCTL_SHDWSEL_MISC just for reading needs
(same value shifted by 12 bits).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.
Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli