Similar to how we handle VXLAN offload, enable support for a single
Geneve tunnel.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding Geneve Rx offload support, refactor the
current VXLAN offload flow to be a bit more generic so that it will be
easier to add the new Geneve code. The fm10k hardware supports one VXLAN
and one Geneve tunnel, so we will eventually treat the VXLAN and Geneve
tunnels identically. To this end, factor out the code that handles the
current list so that we can use the generic flow for both tunnels in the
next patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the event of a surprise remove, we expect the driver to go down,
which includes calling .stop_hw(). However, this function will return an
error because the queues won't appear to cleanly disable. Prevent this
and avoid the unnecessary checks by just returning when
FM10K_REMOVED(hw->hw_addr) is true.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the event of an uncorrectable AER error occurring when the driver has
not loaded, the recovery routines are not done. This is done because
future loads of the driver may not be aware of the IO state and may not
be able to recover at all. In this case, when we next load the driver it
fails due to what appears to be a surprise remove event. Instead, add
a check to ensure that the device is in the normal IO state before
continuing to probe. This allows us to give a more descriptive message
of what is wrong.
Without this change, the driver will attempt to probe up to our first
call of .reset_hw() which will be unable to read registers and act as if
a surprise remove event occurred.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When fm10k_poll fully cleans rings it returns 0. This is incorrect as it
messes up the budget accounting in the core NAPI code. Fix this by
returning actual work done, capped at budget - 1 since the core doesn't
expect a return of the full budget when the driver modifies the NAPI
status.
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While technically not needed, as all our uses of ACCESS_ONCE are scalar
types, we already use READ_ONCE in a few places, and for code
readability we can swap all the uses of the older ACCESS_ONCE into
READ_ONCE.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function is only used in fm10k_ethtool.c, so make it static.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous patch added support to check for hardware Tx pending in the
fm10k_down routine. This support was intended to ensure that we
accurately check what the hardware state is. However, checking for Tx
hangs in this manor during the hotpath results in a large performance
hit. Avoid this by making the hotpath check use the SW counters instead.
Fixes: a0f53cf49cb0 ("fm10k: use actual hardware registers when checking for pending Tx", 2016-06-08)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous patch removed the pci_disable_device() call in
.io_error_detected. This call corresponded to a pci_enable_device_mem()
call within .io_slot_reset handler. Change the call here to
a pci_reenable_device() so that it does not increment and leak the
enable_cnt reference count for the device. Without this change, VF
devices may fail during an unbind/bind, and we'll never zero the
reference counter for the pci_dev structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The pci_enable_msix_range() function returns a positive value of the
number of allocated vectors if it succeeds. On failure it returns
a negative error code. Return this code properly so that the error
message printed by the driver will show the actual error code instead of
being masked by -ENOMEM.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we resume from an AER recovery with many active VFs, the PF sees
many spurious link up and link down events. Prevent this by delaying
link down for at least one second after the resume event.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the fm10k interface is brought up, but the switch manager software is
not running, the driver will continuously request the lport map every
few seconds in the base driver watchdog routine. Eventually after
several minutes the switch mailbox Tx fifo will fill up and the mailbox
will timeout, resulting in a reset. This reset will appear as if for no
reason, and occurs regularly every few minutes until the switch manager
software is loaded.
Prevent this from happening by only requesting the lport map after we've
verified the switch mailbox is tx_ready. In order to simplify code logic
and reduce code duplication, implement this as a new function pointer
"mac.ops.request_lport_map" which the VF will not implement. Otherwise,
we have to duplicate the tx_ready check outside of
fm10k_get_host_state_generic, or re-implement most of
fm10k_get_host_state_generic in the pf version.
The resulting code is simpler and easier to understand, and prevents the
PF from continuously requesting lport map and filling the Tx fifo of
a switch mailbox that isn't ready.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes, a VF driver will lose PCIe address access, such as due to
a PF FLR event. In fm10k_detach_subtask, poll and check whether the
PCIe register space is active again and restore the device when it has.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If an FLR occurs, VF devices will be knocked out of bus master mode, and
the driver will be unable to recover from the reset properly, resulting
in malicious driver events and an infinite reset loop. In the normal
case, the bus master mode will already be enabled and this call will
essentially be a no-op. Since we're doing this every reset, it is
possible we could remove the other calls to pci_set_master() but it
seems not harmful to just leave them in place.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Continuing the effort to commonize the similar suspend/resume flows,
finish up by using the new fm10k_handle_suspand and fm10k_handle_resume
functions for the standard suspend/resume flow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a function level PCI reset is triggered using sysfs, it calls the
driver's .reset_notify error handler. Implement a handler based on the
now split fm10k_prepare_for_reset and fm10k_handle_reset functions, so
that we fully reset the driver when the PCI function level reset occurs.
This also ensures the reset is handled in a clean way by first disabling
all the driver bits first and then restoring them after the function
reset. Previously the stack simply performed a blind function reset and
our driver didn't take any part in the process.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have extracted the necessary steps for a split
suspend/resume flow, re-use these functions instead of using the current
open coded flow. This ensures that we don't miss any steps. It also
ensures that we have the correct driver states set.
Since we'll be handling all of the reset flow ourselves, we no longer
need to request a reset in the io_slot_reset() function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement fm10k_prepare_suspend and fm10k_handle_resume functions which
abstract around the now existing fm10k_prepare_for_reset and
fm10k_handle_reset. The new functions also handle stopping the service
task, which is something that the original re-init flow does not need.
Every other location that does a suspend/resume type flow is expected to
use these functions, because otherwise they may have conflicts with the
running watchdog routines. This also has the effect of preventing
possible surprise remove events during handling of FLR events and PCIe
errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are several flows in the driver which perform the similar function
of tearing down software and restoring software to recover from certain
errors or PCIe events, including:
* fm10k_reinit
* fm10k_suspend/resume
* fm10k_io_error_detected/fm10k_io_resume
In addition, we want to implement a .reset_notify() handler as well
which will also perform similar function.
Rework how the driver codes reset and resume flows by separating out the
reinit logic into two functions "fm10k_prepare_for_reset" and
"fm10k_handle_reset". This first step will allow us to re-use this
functionality in the similar blocks of code instead of re-coding the
same sequence of events slightly different.
The end result should be more maintainable and correct, fixing several
inconsistencies with the work flow.
The new functions expect to take the rtnl_lock() themselves, and it does
have the unfortunate side effect of having the reinit flow take then
release then take the rtnl_lock. However, this minor downside is
out weighted by the benefits of code reduction and reducing needless
difference between these flows.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It turns out that sometimes during a reset the Tx queues will be
temporarily stuck longer than .stop_hw() expects. Work around this issue
by attempting to .stop_hw() first. If it tails, wait a number of
attempts until the Tx queues appear to be drained. After this, attempt
stop_hw() again. This ensures that we avoid waiting if we don't need to,
such as during the first initialization of a VF, and give the proper
amount of time necessary to recover from most situations. It is possible
that the hardware is actually stuck. For PFs, this is usually fixed by
a datapath reset. Unfortunately the VF cannot request a similar reset
for itself.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When stop_hw() routine fails with FM10K_ERR_REQUESTS_PENDING, this
indicates that the Tx or Rx queues did not shutdown within the time
limit. Print a more suitable message at the dev_info level instead of
dev_err.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A while ago, an additional check for the switch being ready was added to
reset_hw. A recent refactor accidentally made this check return an error
code on failure which caused fm10k_probe to fail when the switch wasn't
brought up first. The original reasoning for the check was to prevent
additional data path reset when the fabric wasn't ready yet. However,
there isn't a compelling reason to keep the check, as the data path
reset will restore hardware to a known good state. Remove the check and
perform the data path reset regardless of the switch manager state.
An alternative fix is to return FM10K_SUCCESS instead, and bypass the
actual data path reset. This should be fine as we will perform
a reset_hw once the switch is active. However, since data path reset
will reset many parts of the hardware it seems better to just perform
the reset regardless of switch state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't report FM10K_ERR_REQUESTS_PENDING when we fail to disable queues
within the timeout. This can occur due to a hardware Tx hang, or when
the switch ethernet fabric is resetting while we are transmitting
traffic. It can sometimes take up to 500ms before the Tx DMA engine
gives up. Instead, just skip the DMA engine check and perform
a data-path reset anyways. Add a statistic counter to keep track of the
number of resets occurring while we have pending DMA on the rings.
In order to prevent having to re-assign err to 0, re-order the
last few items of the reset_hw_pf function so that we don't perform
"return err" at the end.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a data path reset is initiated, write control to the PCIE_GMBX is
yanked from the switch manager. The switch manager writes to this
register to clear mailbox global interrupt bits as part of its mailbox
interrupt handling routine. When the device recovers from the data path
reset and these bits are not cleared, it will prevent future mailbox
global interrupts from being triggered. Upon confirming that the device
has exited from a data path reset, clear these bits to ensure the proper
functioning of the mailbox global interrupt.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also prevent updating stats while the interface is down. If we're
already updating stats, just return doing nothing. When we take the
device down, block stat updates until we come back up. This ensures that
we avoid tearing down rings when we're updating statistics, and prevents
updating statistics until we're up.
We can't re-use the __FM10K_DOWN for this because it wouldn't prevent
multiple threads from accessing statistics. Neither does it prevent the
case where we start updating stats and then start going down in another
thread.
The fm10k_get_stats64 is except from this, because it has a completely
different flow which does not suffer from the same issues as
fm10k_update_stats might.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's currently possible for fm10k_update_stats to be called during the
window when we go down and the rings are removed. This can result in
a null pointer dereference. In fm10k_get_stats64 we work around this by
using ACCESS_ONCE and a null pointer check inside the loop. Use this
same flow in the fm10k_update_stats to avoid the potential null pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return early from fm10k_down() when we are already down, since that
means another thread is either already finished or has started going
down, so shouldn't conflict with them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some comments weren't updated to reflect the renaming of ndo's and the
change of arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem (viz
fm10k_service_task, which manages and runs other subtasks) is involved in
normal device operation and requires forward progress under memory
pressure.
create_workqueue has been replaced with alloc_workqueue with max_active
as 0 since there is no need for throttling the number of active work
items.
Since network devices may be used in memory reclaim path,
WQ_MEM_RECLAIM has been set to guarantee forward progress.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The index calculated when looping through the indir array passed to
fm10k_write_reta was incorrectly calculated as the first part i needs to
be multiplied by 4.
Fixes: 0cfea7a65738 ("fm10k: fix possible null pointer deref after kcalloc", 2016-04-13)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While reviewing the i40e driver changes to support page based receive I
realized that I had overlooked the fact that the fm10k hardware required a
512 byte alignment for Rx buffers. This patch is meant to address that by
changing the alignment for Rx buffers to 512 bytes instead of allowing it
to be L1 cache aligned.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FM10K_MAX_DATA_PER_TXD is really just using a bitshift as a power of
2 operation in an efficient manner. We shouldn't represent this as a BIT()
because that obscures the intention of the operation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the Intel ethernet drivers.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type if VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
fm10k_open requires rtnl_lock to be held.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for and handle IPv6 extended headers so that Tx checksum offload
can be done. Also use skb_checksum_help for unexpected cases. This was
originally discovered in ixgbe.
Reported-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update every header file and other locations to consistently use
Intel(R) instead of just Intel. Also update copyright year of files
which we modified.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When writing a new default redirection table, we needed to populate
a new RSS table using ethtool_rxfh_indir_default. We populated this
table into a region of memory allocated using kcalloc, but never checked
this for NULL. Fix this by moving the default table generation into
fm10k_write_reta. If this function is passed a table, use it. Otherwise,
generate the default table using ethtool_rxfh_indir_default, 4 at at
time.
Fixes: 0ea7fae440 ("fm10k: use ethtool_rxfh_indir_default for default redirection table")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Deleting lport when multicast mode is configured to
FM10K_XCAST_MODE_ALLMULTI or FM10K_XCAST_MODE_PROMISC will result in
generating orphaned multicast-group entries in the switch manager.
Before deleting the lport, reset multicast mode to FM10K_XCAST_MODE_NONE
to flush out these multicast-group entries.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original comment may be read incorrectly as referring to checking
the *entire* length is zero. However, it merely checks only the reserved
bits of both length and reserved in a small amount of code. Update the
comment to indicate this is a clever trick and clearly spell out that it
only checks the reserve bits.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a new #define FM10K_VLAN_OVERRIDE even though we're using the exact
same bit. The reason for this is clarity in the code, otherwise you can
read FM10K_VLAN_CLEAR and think it should be removed. Also add a comment
explaining why the FM10K_VLAN_OVERRIDE bit is set.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The diagram represents bit layout of the multi-bit VLAN update message
format. Typically these diagrams are drawn using some power of 2 as the
base, to more easily grasp where fields split. Although the numbers
above can make it somewhat easy to understand which bit you're looking
at, it makes the break points not line up. Re-draw the numbers using
base 8, and mark the bit values every 8 bits at the top. This should
make it more easy to grasp the table quickly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k_tlv_parse_attr is supposed to return FM10K_NOT_IMPLEMENTED for any
TLV who's attribute id lies outside the range of results. It does not do
this today. In addition, the documentation does not indicate that other
attributes which are not implemented for a given TLV will be silently
ignored. Fix this. Clean up the logic so that we don't rely on the fact
that FM10K_NOT_IMPLEMENTED is greater than zero, as this can easily
cause confusion.
A future extension could look into some way of reporting unknown TLVs
in order to make issues more easily discoverable. We can't just return
FM10K_NOT_IMPLEMENTED here because we don't want to drop the entire
message if it has an unknown TLV.
While here, update the copyright year.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k_io_error_detected() does not need to call pci_disable_device(). In
the cases where the reset needs to occur, the stack flow will result in
calling fm10k_remove() which already disables the PCI device. If we
leave the pci_disable_device(), we result in a warning about disabling
an already disabled device.
Many PCI drivers do call pci_disable_device() in their .error_detected()
routines, but it does not appear to be required. In addition, these
drivers have a check "is_pci_enabled()" call in their remove routines,
which is how they chose to handle the duplicate device disable.
This seems incorrect, since the PCI device structure is reference
counted. It is very possible that the reference count for the PCI device
could be greater than 1. In this case, you would remove the PCI device
within the error_detected routine, reducing count to 1, then remove it
again in the remove function, reducing it to zero. This would result in
yet another disable somewhere else failing. Thus, we shouldn't be using
is_pci_enabled() to check for this issue. Instead, just remove the
extraneous pci_device_disable() found within the error_detected routine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, any error responses from the switch manager after an
LPORT_MAP request are silently ignored. At most the mailbox message will
be reported as an error. This can result in unexpected behavior when the
switch manager has configured a port with zero bandwidth. Add support
for reading the fm10k_swapi_error structure from LPORT_MAP responses.
If the message contains the necessary TLV and has a non-zero error code,
report link down, clear the dglort_map, and delay the next
get_host_state call by a reasonable delay. Also log an error message
indicating that the LPORT_MAP request failed.
The delay ensures preventing an interrupt storm on the switch manager,
and reduces the number of mailbox messages we send in this scenario
drastically.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Multicast mode checking is no longer a requirement to perform unicast
and multicast address syncs. Specifically, a device operating in
promiscuous and/or all multicast mode is not excluded. The issue occurs
when the netdev is pre-configured to either multicast mode and is
enabled for the first time. The multicast-group table in the Switch
Manager will be missing obvious multicast entries associated to this
netdev.
Changes were also made to disallow unicast and multicast syncs with
VLAN 0. The Switch Manager considers VLAN 0 to be an invalid entry.
Requests with VLAN 0 by the netdev are only generated when the driver is
freshly installed and the default VID is not set.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 1588 support within fm10k does not work correctly with the current
version of the switch management software, and likely never worked
correctly to begin with. Remove support for PTP/1588. Update copyright
year for all these files while we're touching them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During an AER action response, we were calling fm10k_close without
holding the rtnl_lock() which could lead to possible RCU warnings being
produced due to 64bit stat updates among other causes. Similarly, we
need rtnl_lock() around fm10k_open during fm10k_io_resume. Follow the
same pattern elsewhere in the driver and protect the entire open/close
sequence.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use DRV_SUMMARY, similar to DRV_VERSION so that we don't have to
duplicate the driver summary in multiple places.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk free in Tx cleanup for fm10k and cleans up the
boolean logic in the polling routines for fm10k in the hopes of avoiding
any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes an (ab)use of the ethtool stats API, which could
result in corrupt memory or misleading stat output. The ethtool stats
API is not robust enough to handle varying number of statistics due to
how it requests the size and allocates memory. Remove the poorly conceived
support originally added for extra debug statistics. In the future,
a new stats API may open up the ability to display these statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce duplicate code and the amount of indentation by adding
fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help
add fm10k_stat structures to the ethtool stats callbacks. This helps
increase ease of use for future stat additions, and increases code
readability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF uses a multi-bit update request to clear unused VLANs whenever it
resets. However, an accident in a previous refector broke multi-bit
updates for VFs, due to misreading a comment in fm10k_vf.c and
attempting to reduce code duplication. The problem occurs because
a multi-bit request has a non-zero length, and the PF would simply drop
any request with the upper 16 bits set.
We can't simply remove the check of the upper 16 bits and the call to
fm10k_iov_select vid, because this would remove the checks for default
VID and for ensuring no other VLANs can be enabled except pf_vid when it
has been set. To resolve that issue, this revision uses the
iov_select_vid when we have a single-bit update, and denies any
multi-bit update when the VLAN was administratively set by the PF. This
should be ok since the PF properly updates VLAN_TABLE when it assigns
the PF vid. This ensures that requests to add or remove the PF vid work
as expected, but a rogue VF could not use the multi-bit update as
a loophole to attempt receiving traffic on other VLANs.
Reported-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The fm10k driver used its own code for generating a default indirection
table on device load, which was not the same as the default generated by
ethtool when indir_size of 0 is passed to SRXFH. Take advantage of
ethtool_rxfh_indir_default() and simplify code to write the redirection
table to reduce some code duplication.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
s/funciton/function to resolve a typo, and cleanup grammar on a few
comments regarding processing the VF mailboxes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If 'attr_flag < (1 << (2 * FM10K_TEST_MSG_NESTED))' is ever false, err
will be used uninitialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce duplicate code and the amount of indentation by adding
fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help
add fm10k_stat structures to the ethtool stats callbacks. This helps
increase ease of use for future stat additions, and increases code
readability. Skip handling of the per-queue stats as these will be
reworked in a following patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During fm10k_io_error_detected we were clearing the interrupt scheme
before we freed the MBX IRQ. This causes a kernel panic because the MBX
IRQ are assigned after MSI-X initialization. Clearing the interrupt
scheme results in removing the MSI-X entry table. Fix this by freeing
the MBX IRQ before we clear the interrupt scheme, as we do elsewhere in
the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k_stop_hw_generic calls fm10k_disable_queues_generic, which may
return an error code indicating that the queues were not stopped within
the time limit. Notify the user by displaying a message in the kernel
message ring, in a similar way to how we notify the user when reset_hw
fails. There isn't much we can do to recover from this error, so
currently nothing else is done.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In fm10k_set_num_queues, we previously assigned the base template. This
would always be overwritten by either fm10k_set_qos_queues or
fm10k_set_rss_queues. In either case, we don't need the base values, so
we can just remove them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the C standard dereferencing a variable before it is
checked invokes undefined behavior, and thus compilers are free to
assume the check for NULL isn't necessary. Prevent this by re-ordering
the NULL check of msix_entries in fm10k_free_mbx_irq.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup the remaining instances of using memcpy() instead of the preferred
ether_addr_copy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to crash the kernel in this instance so just warn about the
condition and play on.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use BIT() macro instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The semantic patch that makes this change is available
in scripts/coccinelle/misc/compare_const_fl.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also print an error message incase we do have to reconfigure as this
should no longer happen anymore due to ethtool changes. If it somehow
does occur, user should be made aware of it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tri-states need 'if IS_ENABLED()', booleans should use 'ifdef'.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup a number of issues with function header comments, lower-case
acronyms (i.e. FIFO, TLV), duplicate comments and a stubbed-out header
comment for fm10k_sm_mbx_init.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These structures never change so declare them as const.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When comparing MAC addresses, use ether_addr_equal instead of memcmp to
ETH_ALEN length. Found and replaced using the following sed:
sed -e 's/memcmp\x28\(.*\), ETH_ALEN\x29/!ether_addr_equal\x28\1\x29/'
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to cleanup the exception handling for the paths where
we reset the interrupts and then reconfigure them. In all of these paths
we had very different levels of exception handling. I have updated the
driver so that all of the paths should result in a similar state if we
fail.
Specifically the driver will now unload the mailbox interrupt, free the
queue vectors and MSI-X, and then detach the interface.
In addition for any of the PCIe related resets I have added a check with
the hw_ready function to just make sure the registers are in a readable
state prior to reopening the interface.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TLV format for little endian structures is actually 4 byte aligned
copy. To this end, we need to add an additional __aligned(4) marker
along with __packed to ensure that these structures are actually 4 byte
aligned and packed correctly. Use of just __packed will not work as this
will result in 1byte alignment which is incorrect. Add a comment
explaining the reasoning behind why these structures need the special
treatment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleans up checkpatch GLOBAL_INITIALIZERS error
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to ixgbe and i40e, initialize XPS on driver load so that we can
take advantage of this kernel feature.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make functions that should be static. While we're at it, fix the function
header comment for fm10k_tlv_attr_nest_stop(), and update the copyright
header for fm10k_pf.h, fm10k_tlv.c and fm10k_tlv.h.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function declaration does not need to be 'inline'd here.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses two issues.
First is the fact that the fm10k_mbx_free_irq was assuming msix_entries was
valid and that will not always be the case. As such we need to add a check
for if it is NULL.
Second is the fact that we weren't freeing the IRQ if the mailbox API
returned an error on trying to connect.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the q_vector allocation fails we should free the resources associated
with the MSI-X vector table.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than wrapping fm10k_dcbnl.c and fm10k_debugfs.c support with
#ifdef blocks, just conditionally include the .o files in the Makefile.
Also, since we're modifying it, update the copyright year on the
Makefile.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We haven't bumped the driver version in a while despite many fixes being
pulled in from the out-of-tree Sourceforge driver. Update the version to
match.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using lowercase vlan, vid, or VID, always use VLAN or VLAN ID
in comments when referring to VLANs. The original driver code was
consistent, but recent patches have not been as consistent with this
naming scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Improve code style by removing the unnecessary else block of an if
statement which immediately returns.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid the use of CamelCase for some variable names that previously
slipped through review.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the ether_addr_copy function instead of copying byte-by-byte in a
for-loop by hand.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current default ITR for Tx is overly restrictive. Using a simple
netperf TCP_STREAM test, we top out at about 10Gb/s for a single thread
when running using 1500 byte frames. By reducing the ITR value to 25usec
(up to 40K interrupts a second from 10K), we are able to achieve 36Gb/s
for a single thread TCP stream test.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing adaptive ITR algorithm is overly restrictive. It throttles
incorrectly for various traffic rates, and does not produce good
performance. The algorithm now allows for more interrupts per second,
and does some calculation to help improve for smaller packet loads. In
addition, take into account the new itr_scale from the hardware which
indicates how much to scale due to PCIe link speed.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Reported-by: Alex Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Define a macro for identifying when the itr value is dynamic or
adaptive. The concept was taken from i40e. This helps make clear what
the check is, and reduces the line length to something more reasonable
in a few places.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Intel Ethernet Switch FM10000 Host Interface interrupt throttle
timers are based on the PCIe link speed. Because of this, the value
being programmed into the ITR registers must be scaled accordingly.
For the PF, this is as simple as reading the PCIe link speed and storing
the result. However, in the case of SR-IOV, the VF's interrupt throttle
timers are based on the link speed of the PF. However, the VF is unable
to get the link speed information from its configuration space, so the
PF must inform it of what scale to use.
Rather than pass this scale via mailbox message, take advantage of
unused bits in the TDLEN register to pass the scale. It is the
responsibility of the PF to program this for the VF while setting up the
VF queues and the responsibility of the VF to get the information
accordingly. This is preferable because it allows the VF to set up the
interrupts properly during initialization and matches how the MAC
address is passed in the TDBAL/TDBAH registers.
Since we're modifying fm10k_type.h, we may as well also update the
copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally this statistic was renamed because the method of dropping was
called "drop_oversized_messages", but this logic has changed much, and
this counter does actually represent messages which we failed to
transmit for a number of reasons. Rename the counter back to tx_dropped
since this is when it will increment, and it is less confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous bug was uncovered by addition of a debug stat to indicate the
actual number of DWORDS we pulled from the mbmem. It turned out this was
not the same as the tx_dwords counter. While the previous bug fix should
have corrected this in all cases, add some debug stats that count the
number of DWORDs pushed or pulled from the mbmem. A future debugger may
take advantage of this statistic for debugging purposes. Since we're
modifying fm10k_mbx.h, update the copyright year as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the resultant data type of the mac_update.mac_upper field is u16,
it does not make sense to typecast u8 variables to u32 first. Since
we're modifying fm10k_pf.c, also update the copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.
Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.
In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.
Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks. To resolve this, we added a
check first to ensure that the first queue is infact owned by the VF at
init_hw_vf time. However, the code flow did not reset hw->mac.max_queues
to 0. In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't change netdev hw_features later in fm10k_probe, instead set all
values inside fm10k_alloc_netdev. To do so, we need to know the MAC type
(whether it is PF or VF) in order to determine what to do. This helps
ensure that all logic regarding features is co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The fm10k_msix_clean_rings function runs from hard interrupt context or
with interrupts already disabled in netpoll.
It can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects an issue in which the polling routine would increase
the budget for Rx to at least 1 per queue if multiple queues were present.
This would result in Rx packets being processed when the budget was 0 which
is meant to indicate that no Rx can be handled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on hardware testing, the host interface supports up to 15368 bytes
as the maximum frame size. To determine the correct MTU, we subtract 8
for the internal switch tag, 14 for the L2 header, and 4 for the
appended FCS header, resulting in 15342 bytes of payload for our maximum
MTU on jumbo frames.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible that the PF has not yet assigned resources to the VF.
Although rare, this could result in the VF attempting to read queues it
does not own and result in FUM or THI faults in the PF. To prevent this,
check queue 0 before we continue in init_hw_vf.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This was detected by Coverity.
The function skb_cow_head leaves skb alone on failure, so caller needs
to free.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for actual value NETREG_UNINITIALIZED in case it ever changes from
the current value of zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a private ethtool flag to enable display of these statistics, which
are generally less useful. However, sometimes it can be useful for
debugging purposes. The most useful portion is the ability to see what
the PF thinks the VF mailboxes look like.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we connect to the mailbox, we insert a fake disconnect header so
that the code does not see an invalid header and thus instantly error
every time we bring up the mailbox. However, we incorrectly record the
tail and head from the local perspective. Since the remote end shouldn't
have anything for us, add a "create_fake_disconnect_hdr" function which
inverts the TAIL and HEAD fields. This enables us to connect without any
errors of either TAIL or HEAD incorrectness, and prevents creating
extraneous error messages. This is necessary now since mbx_reset_work
does not actually reset the Tx FIFO head and tail pointers, thus head
and tail might not be equivalent on a reconnect.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a corner case issue with the PF/VF mailbox code.
Currently, fm10k_mbx_reset_work clears various state about the mailbox.
However, it does not clear the Tx FIFO head/tail pointers. We can't
simply clear these pointers as we unintentionally drop untransmitted
messages without error.
Doing nothing results in a possible phantom re-transmission of messages,
since we leave tx.head and tx.tail intact, but clear the tx_pulled and
tail_len values. This means that the PF could continuously re-send a
message which triggers a reset in the VF. Upon reset, the VF will
re-receive the same message after a reconnect.
If we reset the tx.head and tx.tail pointers completely, we end up
dropping some messages that were pending before connect. This results in
missing LPORT_MSG_READY bits, and VFs will end up reporting no link.
However, we can resolve both issues by simply incrementing head to
account for the already transmitted messages, before we reset tx_pulled.
We do this via the same logic as fm10k_mbx_head_pull.
We account for the tail_len which includes all data not yet transmitted,
once we account for the acked data which means re-reading the HEAD
variable from the message header. Then, we drop messages until we've
dropped more than the new tx_pulled value. At this point, resetting
tail_len and tx_pulled, but not tx.head and tx.tail will result in
prevention of the phantom message. It also prevents us from dropping
untransmitted messages upon attempting to Tx into a connect or
disconnect header.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This comment is no longer true due to a couple of mailbox locking
refactors, and we now don't actually do any rtnl protected operations
directly in the mailbox path. Remove this comment as it is factually
incorrect and confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF will send a message to request multicast addresses with the
default VID. In the current code, if the PF has statically assigned a
VLAN to a VF, then the VF will not get the multicast addresses. Fix up
all of the various VLAN messages to use identical checks (since each
check was different). Also use set as a variable, so that it simplifies
our check for whether VLAN matches the pf_vid.
The new logic will allow set of a VLAN if it is zero, automatically
converting to the default VID. Otherwise it will allow setting the PF
VID, or any VLAN if PF has not statically assigned a VLAN. This is
consistent behavior, and allows VF to request either 0 or the
default_vid without silently failing.
Note that we need the check for zero since VFs might not get the default
VID message in time to actually request non-zero VLANs.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we only trigger the data path reset if the
fabric is ready to handle traffic. The general idea is to avoid
triggering the reset unless the switch API is ready for us. Otherwise
we can just postpone the reset until we receive a switch ready
notification.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify behavior of Malicious Driver Detection events. Presently, the
hardware disables the VF queues and re-assigns them to the PF. This
causes the VF in question to continuously Tx hang, because it assumes
that it can transmit over the queues in question. For transient events,
this results in continuous logging of malicious events.
New behavior is to reset the LPORT and VF state, so that the VF will
have to reset and re-enable itself. This does mean that malicious VFs
will possibly be able to continue and attempt malicious events again.
However, it is expected that system administrators will step in and
manually remove or disable the VF in question.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch ensures that VLAN traffic on the default VID will go to the
corresponding VLAN device if it exists. To do this, mask the rx_ring VID
if we have an active VLAN on that VID.
For this to work correctly, we need to update fm10k_process_skb_fields
to correctly mask off the VLAN_PRIO_MASK bits and compare them
separately, otherwise we incorrectly compare the priority bits with the
cleared flag. This also happens to fix a related bug where having
priority bits set causes us to incorrectly classify traffic.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some style issues in debugfs code, and correct ordering of void and
__always_unused. Technically, the order does not matter, but preferred
style is to put the macro between the type and name.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function is no longer used now that we have updated fm10k_slot_warn
functionality.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we store the sw_vid at reset of PF, then we accidentally prevent the
VF from receiving the message to update its default VID. This only
occurs if the VF is created before the PF has come up, which is the
standard way of creating VFs when using the module parameter.
This fixes an issue where we request the incorrect MAC/VLAN
combinations, and prevents us from accidentally reporting some frames as
VLAN tagged.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We re-sync upon going up, so there is little reason to worry about not
syncing immediately with switch. This prevents an error that occurs if
you add a VLAN interface while down.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the MAC address to the list of values recorded on driver
load. The MAC address represents the serial number of the unit and allows
us to track the value should a card be replaced in a system.
The log message should now be similar in output to that of ixgbe.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change pulls out the optimization that assumed that all fragments
would be limited to page size. That hasn't been the case for some time now
and to assume this is incorrect as the TCP allocator can provide up to a
32K page fragment.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the netdev permanent address during fm10k_reinit enables the user
to immediately see the new MAC address on the VF even if the device
isn't up. The previous code required that the device by opened before
changes would appear.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is useful in cases where we connect to a slot at Gen3, but the slot
is behind a bus which only connected at Gen2. This generally only
happens when a PCIe switch is in the sequence of devices, and can be
very confusing when you see slow performance with no obvious cause.
I am aware this patch has a few lines that break 80 characters, but
there does not seem to be a readable way to format them to less than 80
characters. Suggestions welcome.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows us to correctly add a VLAN even if it matches our default
VID. However, we don't want to remove the VID rules once that VLAN is
deleted. Correctly remove the stack layers information of the VLAN, but
then return to forwarding that VID as untagged frames. If we deleted the
VID rules here, we would begin dropping traffic due to VLAN membership
violations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The service task reads some registers as part of its normal routine,
even while the interface is down. Normally this is ok. However, during
suspend we have disabled the PCI device. Due to this, registers will
read in the same way as a surprise-remove event. Disable the service
task while we suspend, and re-enable it after we resume. If we don't do
this, the device could be UP when you suspend and come back from resume
as closed (since fm10k closes the device when it gets a surprise
remove).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c48a11c7ad ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While reviewing the code I noticed that one of the commits added an if
statement followed by a for loop, but the if statement was missing the
braces around the loop. This change corrects the coding style error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF issues an LPORT_STATE request to enable a port that is already
enabled, the PF will first disable the VF LPORT. Then it should
re-enable the VF again with the new requested settings. This ensures
that any switch rules are cleared by deleting the LPORT on the switch.
However, the flow is bugged because we actually check if the VF is
enabled at the end, and thus don't re-enable it. Fix the flow so that we
actually clear the enabled flags as part of our removal of the LPORT.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The reference to err_no was left around after a previous code refactor.
We never use the value, and it doesn't seem to be used in side a hidden
macro reference. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SYSTIME_CFG.Adjust Direction bit is actually supposed to indicate
that the adjustment is positive. Fix the code to align correctly with
hardware and documentation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the __attribute__((packed)) indicator to some structures
which are overlayed onto a TLV message. These structures must be packed
as small as possible in order to correctly align when copied into the
mailbox buffer. Without doing so, the receiving mailbox code incorrectly
parses the values and we get invalid message responses from the switch
manager software.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During initialization, the VF counts its rings by walking the TQDLOC
registers. This works only if the TQMAP/RQMAP registers are set to map
all of the out-of-bound rings back to the first one. This allows the VF
to cleanly detect when it has run out of queues. Update the PF code so
that it resets the empty TQMAP/RQMAP registers post-VFLR to prevent
innocent VF drivers from triggering malicious driver events.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we don't notify the switch at all when the PF
administratively sets a new VLAN or MAC address. This causes the old
addresses to remain valid on the switch table. Since the PF is
overriding any configuration done directly by the VF, we choose to
simply re-create the LPORT for the VF. This does mean that all rules for
the VF will be dropped when we set something directly via the PF, but it
prevents some weird issues where the MAC/VLAN table retains some stale
configuration.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the use of dma_get_required_mask and uses the
simpler dma_set_mask_and_coherent function instead of doing these as
separate steps.
I removed the dma_get_required_mask call because based on some minimal
testing it appears that either (a) we're not doing the right thing with
the call or (b) we don't need it anyways. If the value returned is
<48bits, we'll end up trying with 48 bits anyways. If it's over 48bits,
fm10k can't support that anyways, and we should try 48bits. If 48bits
fails, we'll fallback to 32bits. This cleans up some very funky code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also use %d for error values, since printing in hexadecimal is probably
not helpful.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
l2_accel was checked for NULL at the top of fm10k_dfwd_del_station, and
we return if it is not defined. Due to this, we already know it can't be
null here so a separate check is meaningless. Discovered via cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The value will never be negative, and we use the %u print format. Thus,
use unsigned int for the loop counter. Issue found using cppcheck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This prevents a memory leak in fm10k_set_ringparams. The leak occurs
because we go down, change ring parameters, and then come up. However,
fm10k_down on its own is not clearing the Rx rings. Since fm10k_up
assumes the rings are clean we basically drop the buffers and leak a
bunch of memory. Eventually we hit dirty page faults and reboot the
system. This issue does not occur elsewhere because other flows that
involve fm10k_down go through fm10k_close which immediately called
fm10k_free_all_rx_resources which properly cleans the rings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves a bug in the ts_tx_enqueue code responsible for a
NULL pointer dereference and invalid access of the skb list. We
incorrectly freed the actual skb we found instead of our copy. Thus the
skb queue is essentially invalidated. Resolve this by freeing our clone
in the cases where we did not add it to the queue. This also avoids the
skb memory leak caused by failure to free the clone.
[ 589.719320] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 589.722344] IP: [<ffffffffa0310e60>] fm10k_ts_tx_subtask+0xb0/0x160 [fm10k]
[ 589.723796] PGD 0
[ 589.725228] Oops: 0000 [#1] SMP
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the code flow for setting the IN_PROGRESS bit of
the shinfo for an skb we will be timestamping.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes an issue with adding an invalid multicast address
using the iproute2 tool (ip maddr add <MADDR> dev <dev>). The iproute2
tool and the kernel do not validate or filter the multicast addresses
when adding them to the multicast list. Thus, when synchronizing this
list with an invalid entry, the action will be aborted with an error
since the fm10k driver currently validates the list. Consequently,
multicast entries beyond the invalid one will not be processed and
communicated with the switch via the mailbox. This change makes it so
that invalid addresses will simply be skipped and allows synchronizing
the full list to proceed.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change folds the fm10k_pull_tail call into fm10k_add_rx_frag. The
advantage to doing this is that the fragment doesn't have to be modified
after it is added to the skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The netpoll path will call napi->poll with a budget of 0 in order to clean
the Tx rings only. This change updates the fm10k driver so that it will
correctly support that instead of cleaning 1 Rx frame if a budget of 0 is
received.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent driver changes, bump the version.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
VFs were being improperly added to the switch's multicast group. The
error stems from the fact that incorrect arguments were passed to the
"update_mc_addr" function. It would seem to be a copy paste error since
the parameters are similar to the "update_uc_addr" function.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we call update_max_size it does not drop all oversized messages.
This is due to the difficulty in performing this operation, since it is
a FIFO which makes updating anything other than head or tail very
difficult. To fix this, modify validate_msg_size to ensure that we error
out later when trying to transmit the message that could be oversized.
This will generally be a rare condition, as it requires the FIFO to
include a message larger than the max_size negotiated during mailbox
connect. Note that max_size is always smaller than rx.size so it should
be safe to use here.
Also, update the update_max_size function header comment to clearly
indicate that it does not drop all oversized messages, but only those at
the head of the FIFO.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we forcefully shutdown the mailbox, we then go about resetting max
size to 0, and clearing all messages in the FIFO. Instead, we should
just reset the head pointer so that the FIFO becomes empty, rather than
changing the max size to 0. This helps prevent increment in tx_dropped
counter during mailbox negotiation, which is confusing to viewers of
Linux ethtool statistics output.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of dropped doesn't really mean dropped mailbox messages, but
rather specifically messages which were too large to fit in the remote
Rx FIFO. Rename the stat to more clearly indicate what it means.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the PF receives a request to update a multicast address for the VF,
it checks the enabled multicast mode first. Fix a bug where the VF tried
to set a multicast address before requesting the required xcast mode.
This ensures the multicast addresses are honored as long as the xcast
mode was allowed.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the service task handles varying work that doesn't all require the
interface to be up, launch the service timer immediately. This ensures
that we continually check the mailbox, as well as handle other tasks
while the device is down.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The header comment included a miscopy of a C-code line, and also
mis-used Rx FIFO when it clearly meant Tx FIFO
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a header comment explaining why we have the somewhat crazy mailbox
flow. This flow is necessary as it prevents the PF<->SM mailbox from
being flooded by the VF messages, which normally trigger a message to
the PF. This helps prevent the case where we see a PF mailbox timeout.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we already schedule the service task, we can just wait for this
task to handle the mailbox events from the VF. This reduces some complex
code flow, and makes it so we have a single path for handling the VF
messages. There is a possibility that we have a slight delay in handling
VF messages, but it should be minimal.
The result of tx_complete and !rx_ready is insufficient to determine
whether we need to process the mailbox. There is a possible race
condition whereby the VF fills up the mbmem for us, but we have already
recently processed the mailboxes in the interrupt. During this time,
the interrupt is disabled. Thus, our Rx FIFO is empty, but the mbmem now
has data in it. Since we continually check whether Rx FIFO is empty, we
then never call process. This results in the possibility to prevent PF
from handling the VF mailbox messages.
Instead, just call process every time, despite the fact that we may or
may not have anything to process for the VF. There should be minimal
overhead for doing this, and it resolves an issue where the VF never
comes up due to never getting response for its SET_LPORT_STATE message.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we run the watchdog periodically, which might take a while and
potentially monopolize the system default workqueue, create our own
separate work queue. This also helps reduce and stabilize latency
between scheduling the work in our interrupt and actually performing
the work. Still use a timer for the regular scheduled interval but
queue the work onto its own work queue.
It seemed overkill to create a single workqueue per interface, so we
just spawn a single work queue for all interfaces upon driver load. For
this reason, use a multi-threaded workqueue with one thread per
processor, rather than single threaded queue.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When returning virtualization queues from the VF back to the PF, do not
retain the VF rate limiter.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Todd Russell <todd.a.russell@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Named it tx_hang_count to differentiate it from tx_hwtstamp_timeout.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incrementing the tx_timeout_count for both the Tx hang
and then for all reset flows. Instead, we should only increment
tx_timeout_count in the Tx hang path, so that our Tx hang counter
does not increment when it was not caused by a Tx hang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we already print this message when a reset is requested via the
RESET_REQUESTED flag, we do not need to print it before setting the
flag.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue with ethtool stats displaying useless
values on the VF, because some stats simply have no meaning to the VF.
Resolve this by splitting these out into PF_STATS and only showing them
if we aren't the VF.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even though it shouldn't strictly matter, don't count queue stats higher
than the max_queues value stored for this mac. This ensures that we
don't attempt to check queues which don't belong to use in VFs. This
shouldn't be a visible change, as the VFs should see zero for queues
which don't belong to them.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we show statistics for all 128 queues, even though we don't
necessarily have that many queues available especially in the VF case.
Instead, use the hw->mac.max_queues value, which tells us how many
queues we actually have, rather than the space for the rings we
allocated. In this way, we prevent dumping statistics that are useless
on the VF.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the user was not allowed to create a VLAN interface on top
of the switch default vid.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The were several functions which had parameters which were never or
sometimes used in functions. To resolve possible compiler warnings,
use __always_unused or __maybe_unused kernel macros to resolve.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds a function called "fm10k_netpoll" that's used to define
"ndo_poll_controller" in "fm10k_netdev_ops". This is required to enable
support for "netconsole" in fm10k.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the VFs do not read the default VLAN during initialization,
so they will not be able to indicate untagged frames properly.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Corrected a spelling mistake that was found over time.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Output of ethtool was reporting 2 rx_errors entries. This change
removes one of the redundant entries.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
The function collecting Tx statistics was actually using values from the RX
ring. Thus, Tx and Rx statistics values reported by "ifconfig" will
return identical values. This change corrects this error and the Tx
statistics is now reading from the Tx ring.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
The device appears to use a 64 bit nanoseconds register, and so with
this patch the driver should be ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a few silly typos in the code and checkpatch warnings in support of
general code cleanliness.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The introduction of ndo_features_check allows drivers to report their
offload capabilities per-skb. Implement this in fm10k to take advantage
of this new functionality.
Reported-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller