Once the E822 device has sent and received one packet, the hardware
computes the internal delay of the PHY using a process known as Vernier
calibration. This calibration calculates a more accurate offset for the
Tx and Rx timestamps. To make use of this offset, we need to exit the
bypass mode. This cannot be done until the PHY has completed offset
calibration, as indicated by the offset valid bits.
To handle this, introduce a kthread work item which will poll the offset
valid bits every few milliseconds seeing if it is safe to exit bypass
mode.
Once we have finished calibrating the offsets, we can program the total
Tx and Rx offset registers and turn off the bypass bit. This allows the
hardware to include the more precise vernier calibration offset, and
improves the timestamp precision.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The E822 device has a Clock Generation Unit (CGU) responsible for
determining the clock frequency that drives the timers.
Ensure this function is initialized when bringing up the PTP support, so
that the clock has a known frequency.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement support for the basic operations needed to enable the PTP
hardware clock on E822 devices.
This includes implementations for the various PHY access functions, as
well as the ability to start and stop the PHY timers. This is different
from the E810 device because the configuration depends on link speed, so
we cannot just start the PHYs immediately. We must wait until the link
is up to get proper values for the speed based initialization.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert the clk_freq value into the associated time_ref frequency value
for E822 devices. This simplifies determining the time reference value
for the clock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When we enable support for E822 devices, there are some additional
steps required to initialize the PTP hardware clock. To make this easier
to implement as device-specific behavior, refactor the register setups
in ice_ptp_init_owner to a new ice_ptp_init_phc function defined in
ice_ptp_hw.c
This function will have a common section, and an e810 specific
sub-implementation.
This will enable easily extending the functionality to cover the E822
specific setup required to initialize the hardware clock generation
unit. It also makes it clear which steps are E810 specific vs which ones
are necessary for all ice devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_ptp_hw.c file introduced a bunch of uses of "int status" instead
of the more traditional "int err" or "int ret". These are actually
traditional Linux error codes (as opposed to the recently removed
ice_status enumeration values).
We're about to add a bunch of new functions to ice_ptp_hw.c. It's
normally preferred in the ice driver to use "int ret" or "int err" when
dealing with error code values.
Instead of making the new functions use "int status" lets just fix all
of ice_ptp_hw.c to use "int err". This will match the new functions and
ensures a consistent style across at least the PTP related files.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The tstamp_config structure is being set inside of
ice_ptp_cfg_timestamp, which is the function used to set Tx and
Rx timestamping during initialization.
This function is also used in order to set the PHY port timestamping
status. However, it makes sense to always set the tstamp_config directly
whenever the ice_set_tx_tstamp or ice_set_rx_tstamp functions are
called.
Move assignment of tstamp_config into the related functions and out of
ice_ptp_cfg_timestamp.
Now that we assign the timestamp mode in the relevant functions, we no
longer modify the config value in ice_set_timestamp_mode. In turn, we
no longer want to copy that config value into the PF cached structure.
Instead, this is now the source of truth for actual configuration. On
success of ice_set_timestamp_mode, copy the real configured mode back to
report it out to userspace.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A future change will add additional possible increment values for the
E822 device support. To handle this, we want to look up the increment
value to use instead of hard coding it to the nominal value for E810
devices. Introduce ice_base_incval as a function to get the best nominal
increment value to use.
For now, it just returns the E810 value, but will be refactored in the
future to look up the value based on the device type and configured
clock frequency.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The PF reset does not reset PHC and PHY clocks so it's unnecessary to
stop them and reinitialize after the reset.
Configuring timestamping changes the VSI fields so it needs to be
performed after VSIs are initialized, which was not done in case of a
reset.
Suggested-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pasi Vaananen <pvaanane@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yellow Carp Ethernet devices do not require
Autonegotiation CDR workaround, hence disable the same.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Newer generation Hardware uses the slightly different
port speed bit widths, so alter the existing port speed
bit range to extend support to the newer generation hardware
while maintaining the backward compatibility with older
generation hardware.
The previously reserved bits are now being used which
then requires the adjustment to the BIT values, e.g.:
Before:
PORT_PROPERTY_0[22:21] - Reserved
PORT_PROPERTY_0[26:23] - Supported Speeds
After:
PORT_PROPERTY_0[21] - Reserved
PORT_PROPERTY_0[26:22] - Supported Speeds
To make this backwards compatible, the existing BIT
definitions for the port speeds are incremented by one
to maintain the original position.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yellow Carp Ethernet devices use the existing PCI ID but
the window settings for the indirect PCS access have been
altered. Add the check for Yellow Carp Ethernet devices to
use the new register values.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend lan966x driver with fdb support by implementing the switchdev
calls SWITCHDEV_FDB_ADD_TO_DEVICE and SWITCHDEV_FDB_DEL_TO_DEVICE.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently allow a port to be part or not of the multicast flooding mask.
By implementing the switchdev calls SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS
and SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the driver to support vlan filtering by implementing the
switchdev calls SWITCHDEV_OBJ_ID_PORT_VLAN,
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic support to offload in the HW the forwarding of the
frames. The driver registers to the switchdev callbacks and implements
the callbacks for attributes SWITCHDEV_ATTR_ID_PORT_STP_STATE and
SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME.
It is not allowed to add a lan966x port to a bridge that contains a
different interface than lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lan966x_port_change_rx_flags() was used only when
IFF_PROMISC flag was set. In that case it was setting to copy all the
frames to the CPU instead of removing any RX filters. Therefore remove
it.
Fixes: d28d6d2e37 ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for adding/removing mac entries in the SW list
of entries and in the HW table. This is used by the bridge
functionality.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for handling the interrupts generated by the
analyzer. Currently, only the MAC table generates these interrupts.
The MAC table will generate an interrupt whenever it learns or forgets
an entry in the table. It is the SW responsibility figure out which
entries were added/removed.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the registers that will be used to enable switchdev and
vlan functionality in the HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the devlink health reporter registered by mlxsw to report new
health events and their related parameters. These are meant to aid in
debugging of hardware / firmware issues.
Beside the test event ('MLXSW_REG_MFDE_EVENT_ID_TEST') that is triggered
following the devlink health 'test' sub-command, the new events are used
to report the triggering of asserts in firmware code
('MLXSW_REG_MFDE_EVENT_ID_FW_ASSERT') and hardware issues
('MLXSW_REG_MFDE_EVENT_ID_FATAL_CAUSE').
Each event is accompanied with a severity parameter and per-event
parameters that are meant to help root cause the detected issue.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the Monitoring Firmware Debug (MFDE) register with new events and
their related parameters. These events will be utilized by
devlink-health in the next patch.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a series of if statements that handle different events to a
switch case statement. Encapsulate the per-event code in different
functions to simplify the code.
This is a preparation for subsequent patches that will add more events
that need to be handled.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the MFDE register field names are using the convention:
reg_mfde_<NAME_OF_FIELD>, and do not consider the name of the MFDE
event.
Fix the field names so they fit the more accurate convention:
reg_mfde_<NAME_OF_EVENT>_<NAME_OF_FIELD>.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0a6890b9b4 ("bnx2x: Utilize FW 7.13.15.0.")
added validation for fastpath HSI versions for different
client init which was not meant for SR-IOV VF clients, which
resulted in firmware asserts when running VF clients with
different fastpath HSI version.
This patch along with the new firmware support in patch #1
fixes this behavior in order to not validate fastpath HSI
version for the VFs.
Fixes: 0a6890b9b4 ("bnx2x: Utilize FW 7.13.15.0.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware addresses few important issues and enhancements
as mentioned below -
- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility
This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add index to flow_action_entry structure and delete index from police and
gate child structure.
We make this change to offload tc action for driver to identify a tc
action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will allow users to offload tc actions independent of
classifier in the software datapath.
In preparation for this, teach all drivers that support offload of the flow
tables to reject such configuration as currently none of them support it.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-12-17
Brett Creeley says:
This patch series adds support in the iavf driver for communicating and
using VIRTCHNL_VF_OFFLOAD_VLAN_V2. The current VIRTCHNL_VF_OFFLOAD_VLAN
is very limited and covers all 802.1Q VLAN offloads and filtering with
no granularity.
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 adds more granularity, flexibility,
and support for 802.1ad offloads and filtering. This includes the VF
negotiating which VLAN offloads/filtering it's allowed, where VLAN tags
should be inserted and/or stripped into and from descriptors, and the
supported VLAN protocols.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The debugfs_create_dir() function never returns NULL. It does return
error pointers but in normal situations like this there is no need to
check for errors.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211217071037.GE26548@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is already an "int err" declared at the start of the function so
re-use that instead of declaring a shadow err variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211217070735.GC26548@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following warning is fixed with additional config dependencies:
s390-linux-ld: drivers/net/ethernet/engleder/tsnep_main.o: in function `tsnep_probe':
tsnep_main.c:(.text+0x1de6): undefined reference to `devm_ioremap_resource'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20211216200154.1520-1-gerhard@engleder-embedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For VIRTCHNL_VF_OFFLOAD_VLAN, PF's would limit the number of VLAN
filters a VF was allowed to add. However, by the time the opcode failed,
the VLAN netdev had already been added. VIRTCHNL_VF_OFFLOAD_VLAN_V2
added the ability for a PF to tell the VF how many VLAN filters it's
allowed to add. Make changes to support that functionality.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the VF to support 802.1Q and 802.1ad VLAN insertion and stripping if
successfully negotiated via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS.
Multiple changes were needed to support this new functionality.
1. Added new aq_required flags to support any kind of VLAN stripping and
insertion offload requests via virtchnl.
2. Added the new method iavf_set_vlan_offload_features() that's
used during VF initialization, VF reset, and iavf_set_features() to
set the aq_required bits based on the current VLAN offload
configuration of the VF's netdev.
3. Added virtchnl handling for VIRTCHNL_OP_ENABLE_STRIPPING_V2,
VIRTCHNL_OP_DISABLE_STRIPPING_V2, VIRTCHNL_OP_ENABLE_INSERTION_V2,
and VIRTCHNL_OP_ENABLE_INSERTION_V2.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the PF to set the location of the Tx and Rx VLAN tag for insertion and
stripping offloads. In order to support this functionality a few changes
are needed.
1. Add a new method to cache the VLAN tag location based on negotiated
capabilities for the Tx and Rx ring flags. This needs to be called in
the initialization and reset paths.
2. Refactor the transmit hotpath to account for the new Tx ring flags.
When IAVF_TXR_FLAGS_VLAN_LOC_L2TAG2 is set, then the driver needs to
insert the VLAN tag in the L2TAG2 field of the transmit descriptor.
When the IAVF_TXRX_FLAGS_VLAN_LOC_L2TAG1 is set, then the driver needs
to use the l2tag1 field of the data descriptor (same behavior as
before).
3. Refactor the iavf_tx_prepare_vlan_flags() function to simplify
transmit hardware VLAN offload functionality by only depending on the
skb_vlan_tag_present() function. This can be done because the OS
won't request transmit offload for a VLAN unless the driver told the
OS it's supported and enabled.
4. Refactor the receive hotpath to account for the new Rx ring flags and
VLAN ethertypes. This requires checking the Rx ring flags and
descriptor status bits to determine the location of the VLAN tag.
Also, since only a single ethertype can be supported at a time, check
the enabled netdev features before specifying a VLAN ethertype in
__vlan_hwaccel_put_tag().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Based on VIRTCHNL_VF_OFFLOAD_VLAN_V2, the VF can now support more VLAN
capabilities (i.e. 802.1AD offloads and filtering). In order to
communicate these capabilities to the netdev layer, the VF needs to
parse its VLAN capabilities based on whether it was able to negotiation
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or neither of
these.
In order to support this, add the following functionality:
iavf_get_netdev_vlan_hw_features() - This is used to determine the VLAN
features that the underlying hardware supports and that can be toggled
off/on based on the negotiated capabiltiies. For example, if
VIRTCHNL_VF_OFFLOAD_VLAN_V2 was negotiated, then any capability marked
with VIRTCHNL_VLAN_TOGGLE can be toggled on/off by the VF. If
VIRTCHNL_VF_OFFLOAD_VLAN was negotiated, then only VLAN insertion and/or
stripping can be toggled on/off.
iavf_get_netdev_vlan_features() - This is used to determine the VLAN
features that the underlying hardware supports and that should be
enabled by default. For example, if VIRTHCNL_VF_OFFLOAD_VLAN_V2 was
negotiated, then any supported capability that has its ethertype_init
filed set should be enabled by default. If VIRTCHNL_VF_OFFLOAD_VLAN was
negotiated, then filtering, stripping, and insertion should be enabled
by default.
Also, refactor iavf_fix_features() to take into account the new
capabilities. To do this, query all the supported features (enabled by
default and toggleable) and make sure the requested change is supported.
If VIRTCHNL_VF_OFFLOAD_VLAN_V2 is successfully negotiated, there is no
need to check VIRTCHNL_VLAN_TOGGLE here because the driver already told
the netdev layer which features can be toggled via netdev->hw_features
during iavf_process_config(), so only those features will be requested
to change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support the new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability the
VF driver needs to rework it's initialization state machine and reset
flow. This has to be done because successful negotiation of
VIRTCHNL_VF_OFFLOAD_VLAN_V2 requires the VF driver to perform a second
capability request via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS before
configuring the adapter and its netdev.
Add the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit when sending the
VIRTHCNL_OP_GET_VF_RESOURECES message. The underlying PF will either
support VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or
neither. Both of these offloads should never be supported together.
Based on this, add 2 new states to the initialization state machine:
__IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS
__IAVF_INIT_CONFIG_ADAPTER
The __IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS state is used to request/store
the new VLAN capabilities if and only if VIRTCHNL_VLAN_OFFLOAD_VLAN_V2
was successfully negotiated in the __IAVF_INIT_GET_RESOURCES state.
The __IAVF_INIT_CONFIG_ADAPTER state is used to configure the
adapter/netdev after the resource requests have finished. The VF will
move into this state regardless of whether it successfully negotiated
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2.
Also, add a the new flag IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS and set
it during VF reset. If VIRTCHNL_VF_OFFLOAD_VLAN_V2 was successfully
negotiated then the VF will request its VLAN capabilities via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS during the reset. This is needed
because the PF may change/modify the VF's configuration during VF reset
(i.e. modifying the VF's port VLAN configuration).
This also, required the VF to call netdev_update_features() since its
VLAN features may change during VF reset. Make sure to call this under
rtnl_lock().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmG8i3cRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZumyAf7BlhO1TUuwhhs9y6fi6KLa/pEOmkx2SRf
9AuEfxxrLPhlzh29Dz4Bn8B+KBG6HFQ1FngSwIAVjLL5pX/1ARBMx9B2TDf9p/Sb
UgkE6WOX29s7LXuC2lDnBnvnKbf5/rdLmZPZCFCv/iKaGAJAYYXYSQjtj5/Fmdkc
PhQNgALWG9a02bfSLk1MlF1lCqt0hsKFQkza29jTa9CKcWYZFK3sTl1spbHAN5yQ
YJMecy+fSxCSuJPZB3elG5os69sz3WGoFY/AYCWoUODNZo18Z4kiAXwurPDIM+GW
3e/lzXe29V1TB36haNe9/C5F2uwoYWGSoWwHcZ62lLpNhJ649wJDbw==
=4wFO
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
* tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits)
wcn36xx: Implement beacon filtering
wcn36xx: Fix physical location of beacon filter comment
wcn36xx: Fix beacon filter structure definitions
ath11k: Use reserved host DDR addresses from DT for PCI devices
dt: bindings: add new DT entry for ath11k PCI device support
wilc1000: Improve WILC TX performance when power_save is off
wl1251: specify max. IE length
rsi: fix array out of bound
wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"
wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx
wilc1000: Rename irq handler from "WILC_IRQ" to netdev name
wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"
wilc1000: Fix spurious "FW not responding" error
wilc1000: Remove misleading USE_SPI_DMA macro
wilc1000: Fix missing newline in error message
wilc1000: Fix copy-and-paste typo in wilc_set_mac_address
rtw89: coex: Update COEX to 5.5.8
rtw89: coex: Cancel PS leaving while C2H comes
rtw89: coex: Update BT counters while receiving report
rtw89: coex: Define LPS state for BTC using
...
====================
Link: https://lore.kernel.org/r/20211217130952.34887C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX fencing allows the driver to know that any prior change to the RQs has
finished, e.g. when the RQs are disabled/enabled or the hashkey/indirection
table are changed, RX fencing is required.
Remove the previous workaround "ssleep(1)" and add the real support for
RX fencing as the PF driver supports the MANA_FENCE_RQ request now (any
old PF driver not supporting the request won't be used in production).
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/20211216001748.8751-1-decui@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eliminate the following coccicheck warning:
./drivers/net/ethernet/vertexcom/mse102x.c:414:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20211216015433.83383-1-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current use of circular buffer to manage stats_context_id is
very obscure, and it will cause problem if its element size is
not power of two. So change the use more straightforward and
scalable, and also change that for mask_id to keep consistency.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/1639618621-5857-1-git-send-email-yinjun.zhang@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- dpaa2-eth: fix buffer overrun when reporting ethtool statistics
Current release - new code bugs:
- bpf: fix incorrect state pruning for <8B spill/fill
- iavf:
- add missing unlocks in iavf_watchdog_task()
- do not override the adapter state in the watchdog task (again)
- mlxsw: spectrum_router: consolidate MAC profiles when possible
Previous releases - regressions:
- mac80211, fix:
- rate control, avoid driver crash for retransmitted frames
- regression in SSN handling of addba tx
- a memory leak where sta_info is not freed
- marking TX-during-stop for TX in in_reconfig, prevent stall
- cfg80211: acquire wiphy mutex on regulatory work
- wifi drivers: fix build regressions and LED config dependency
- virtio_net: fix rx_drops stat for small pkts
- dsa: mv88e6xxx: unforce speed & duplex in mac_link_down()
Previous releases - always broken:
- bpf, fix:
- kernel address leakage in atomic fetch
- kernel address leakage in atomic cmpxchg's r0 aux reg
- signed bounds propagation after mov32
- extable fixup offset
- extable address check
- mac80211:
- fix the size used for building probe request
- send ADDBA requests using the tid/queue of the aggregation
session
- agg-tx: don't schedule_and_wake_txq() under sta->lock,
avoid deadlocks
- validate extended element ID is present
- mptcp:
- never allow the PM to close a listener subflow (null-defer)
- clear 'kern' flag from fallback sockets, prevent crash
- fix deadlock in __mptcp_push_pending()
- inet_diag: fix kernel-infoleak for UDP sockets
- xsk: do not sleep in poll() when need_wakeup set
- smc: avoid very long waits in smc_release()
- sch_ets: don't remove idle classes from the round-robin list
- netdevsim:
- zero-initialize memory for bpf map's value, prevent info leak
- don't let user space overwrite read only (max) ethtool parms
- ixgbe: set X550 MDIO speed before talking to PHY
- stmmac:
- fix null-deref in flower deletion w/ VLAN prio Rx steering
- dwmac-rk: fix oob read in rk_gmac_setup
- ice: time stamping fixes
- systemport: add global locking for descriptor life cycle
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=VIbd
-----END PGP SIGNATURE-----
Merge tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from mac80211, wifi, bpf.
Relatively large batches of fixes from BPF and the WiFi stack, calm in
general networking.
Current release - regressions:
- dpaa2-eth: fix buffer overrun when reporting ethtool statistics
Current release - new code bugs:
- bpf: fix incorrect state pruning for <8B spill/fill
- iavf:
- add missing unlocks in iavf_watchdog_task()
- do not override the adapter state in the watchdog task (again)
- mlxsw: spectrum_router: consolidate MAC profiles when possible
Previous releases - regressions:
- mac80211 fixes:
- rate control, avoid driver crash for retransmitted frames
- regression in SSN handling of addba tx
- a memory leak where sta_info is not freed
- marking TX-during-stop for TX in in_reconfig, prevent stall
- cfg80211: acquire wiphy mutex on regulatory work
- wifi drivers: fix build regressions and LED config dependency
- virtio_net: fix rx_drops stat for small pkts
- dsa: mv88e6xxx: unforce speed & duplex in mac_link_down()
Previous releases - always broken:
- bpf fixes:
- kernel address leakage in atomic fetch
- kernel address leakage in atomic cmpxchg's r0 aux reg
- signed bounds propagation after mov32
- extable fixup offset
- extable address check
- mac80211:
- fix the size used for building probe request
- send ADDBA requests using the tid/queue of the aggregation
session
- agg-tx: don't schedule_and_wake_txq() under sta->lock, avoid
deadlocks
- validate extended element ID is present
- mptcp:
- never allow the PM to close a listener subflow (null-defer)
- clear 'kern' flag from fallback sockets, prevent crash
- fix deadlock in __mptcp_push_pending()
- inet_diag: fix kernel-infoleak for UDP sockets
- xsk: do not sleep in poll() when need_wakeup set
- smc: avoid very long waits in smc_release()
- sch_ets: don't remove idle classes from the round-robin list
- netdevsim:
- zero-initialize memory for bpf map's value, prevent info leak
- don't let user space overwrite read only (max) ethtool parms
- ixgbe: set X550 MDIO speed before talking to PHY
- stmmac:
- fix null-deref in flower deletion w/ VLAN prio Rx steering
- dwmac-rk: fix oob read in rk_gmac_setup
- ice: time stamping fixes
- systemport: add global locking for descriptor life cycle"
* tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (89 commits)
bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
selftest/bpf: Add a test that reads various addresses.
bpf: Fix extable address check.
bpf: Fix extable fixup offset.
bpf, selftests: Add test case trying to taint map value pointer
bpf: Make 32->64 bounds propagation slightly more robust
bpf: Fix signed bounds propagation after mov32
sit: do not call ipip6_dev_free() from sit_init_net()
net: systemport: Add global locking for descriptor lifecycle
net/smc: Prevent smc_release() from long blocking
net: Fix double 0x prefix print in SKB dump
virtio_net: fix rx_drops stat for small pkts
dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED
sfc_ef100: potential dereference of null pointer
net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup
net: usb: lan78xx: add Allied Telesis AT29M2-AF
net/packet: rx_owner_map depends on pg_vec
netdevsim: Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
dpaa2-eth: fix ethtool statistics
ixgbe: set X550 MDIO speed before talking to PHY
...
ath.git patches for v5.17. Major changes:
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The prima driver facilitates the direct programming of beacon filter tables via
SMD commands.
The purpose of beacon filters is quote:
/* When beacon filtering is enabled, firmware will
* analyze the selected beacons received during BMPS,
* and monitor any changes in the IEs as listed below.
* The format of the table is:
* - EID
* - Check for IE presence
* - Byte offset
* - Byte value
* - Bit Mask
* - Byte reference
*/
The default filter table looks something like this:
tBeaconFilterIe gaBcnFilterTable[12] =
{
{ WLAN_EID_DS_PARAMS, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_ERP_INFO, 0u, { 0u, 0u, 248u, 0u } },
{ WLAN_EID_EDCA_PARAM_SET, 0u, { 0u, 0u, 240u, 0u } },
{ WLAN_EID_QOS_CAPA, 0u, { 0u, 0u, 240u, 0u } },
{ WLAN_EID_CHANNEL_SWITCH, 1u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_QUIET, 1u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 1u, 0u, 248u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 2u, 0u, 235u, 0u } },
{ WLAN_EID_HT_OPERATION, 0u, { 5u, 0u, 253u, 0u } },
{ WLAN_EID_PWR_CONSTRAINT, 0u, { 0u, 0u, 0u, 0u } },
{ WLAN_EID_OPMODE_NOTIF, 0u, { 0u, 0u, 0u, 0u } }
};
Add in an equivalent filter set as present in the prima Linux driver.
For now omit the beacon filter "rem" command as the driver does not have an
explicit call to that SMD command. The filter mask should only count when
we are inside BMPS anyway.
Replicating the ability to program the filter table gives us scope to add and
remove elements in future. For now though this patch makes the rote-copy of the
downstream Linux beacon filter table, which we can tweak as desired from now
on.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-4-bryan.odonoghue@linaro.org
The comment in the header with respect to beacon filtering makes a
reference to "the structure above" and "the structure below" which would be
informative if the comment appeared in the right place but, it does not.
Fix the comment location so that it a least makes sense w/r/t the physical
location statements.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-3-bryan.odonoghue@linaro.org
The beacon filter structures need to be packed. Right now its fine because
we don't yet use these structures so just pack them without marking it for
backporting.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211214134630.2214840-2-bryan.odonoghue@linaro.org
Jacob Keller