Previous init path was based on old specs from old driver. Update it
as much as possible leaving some TODOs for not implemented functions.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move table init to tables_nphy.c, detect newer PHY which use different init.
We don't init newer PHYs yet but this at least shows what more is needed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following line shows my BCM4328 detected on SSB. We didn't include 0x0C rev.
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0C, vendor 0x4243)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously ath9k left the initialization of slot timing and ACK/CTS
timeout to the mode specific initvals. This does not handle short vs
long slot in 2.4 GHz and uses a rather strange value for the 2.4 GHz
ACK timeout (64 usec).
This patch uses the proper ath9k_hw functions for setting slot time and
timeouts and also implements the switch between short and long slot
time in 2.4 GHz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes memory leak in ieee80211_send_probe_req, which
is introduced in 7c12ce8b854df346388ea56d684784e3484012cf:
mac80211: use Probe Request template when sending a direct scan
The patch is against the latest wireless-test tree.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Normally 5GHz does not have a concept of long vs short slot time,
however the slot time that it ends up using is the same as for 2.4 GHZ
and use_short_slot == true
Because of that, it makes more sense to force use_short_slot = true
whenever 5 GHz is being used, so that this particular check does not
have to be in every single driver that uses this flag.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In practice APs do not send country IE channel triplets for channels
the AP is not operating on and if they were to do so they would have
to use the regulatory extension which we currently do not process.
No AP has been seen in practice that does this though so just drop
those country IEs.
Additionally it has been noted the first series of country IE
channels triplets are specific to the band the AP sends. Propagate
the band on which the country IE was found on reject the country
IE then if the triplets are ever oustide of the band.
Although we now won't process country IE information with multiple
band information we leave the intersection work as is as it is
technically possible for someone to want to eventually process these
type of country IEs with regulatory extensions.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_offchannel_return is called, it needs to re-enabled TX
queues that have been stopped in ieee80211_offchannel_stop_beaconing or
ieee80211_offchannel_stop_station. It happens if we are doing a scan with an
IBSS interface. In this case, the interface stopped transmitting.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In wireless-testing, commit 7044cc56 added struct ieee80211_hdr_3addr
to include/linux/ieee80211.h. This definition collides with one that is
in the r8187se driver in staging.
The conflict is resolved by changing r8187se to use the definition from
include/linuc/ieee80211.h.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous to this and the last patch, titled,
"cfg80211: Fix 2 GHz subband calculation for country IEs"
we would end up treating these IEs as single channel units. These are in
fact just bogus IE triplets so ignore the entire IE if these are found.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There has been some confusion how drivers should implement powersave
support. Improve the documentation a bit to make it more clear what
drivers need to do. Also mention about U-APSD.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were some warnings about missing documentation and a missing reference.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device has to be marked as invalid before
registering the ISR. HW initialization takes place
after the ISR has been registered, and the invalid
flag is eventually cleared in the ->stop() callback.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In f41f3f373d the B43 driver was ported
to use the cfg80211 API for rfkill and consequently the config option
was dropped (RFKILL is now unconditionally enabled).
However in the Kernel Info the feature is still checked and reported
missing. This patch just removes the conditional and the relevant code
blocks while still reporting that feature unconditionally would be
another option (it's always there).
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are unused and as with a previous patch 5ef5da for wl1251
this removes some other unused flags. the IRQ_MASK specifically
conflicts with include/pcmcia/cs.h when using compat-wireless.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance module information with the names of the firmware files
that could be used by this driver. This helps tools like Jockey to
correctly detect and/or install the firmware files relevant to
this driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Country IEs triplets are getting an extra channel with
the current count. This does not affect regulatory because
we always took the intersection between what the AP gave
and what CRDA believed is correct.
This however does fix processing some Country IEs with multiple
sequential 2 GHz triplets. Since our parser and the spec mandates
all channels be monitonically increasing we would drop the IE after
noticing the second triplet begins on a channel already processed.
APs that send these type of country IEs seems rare though.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: http://bugs.launchpad.net/bugs/488636
Enhances module information with the names of the firmware files
that could be used by this driver. This helps tools like Jockey to
correctly detect and/or install the firmware files relevant to
this driver.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 6c853da3f3.
From Message-ID: <1262663293.551.117.camel@debian>
On Sat, 2010-01-02 at 22:09 +0800, Dan Carpenter wrote:
> It don't think 6c853da3f3 is right. That's the patch
> titled "iwmc3200wifi: fix array out-of-boundary access"
>
> Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
> index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().
>
> In 2.6.33-rc2 IWM_RX_ID_GET_HASH() doesn't go as high as IWM_RX_ID_HASH
> and I don't see any array out-of-bounds.
>
> #define IWM_RX_ID_GET_HASH(id) ((id) % IWM_RX_ID_HASH)
Ah, you are right. I took '%' for '&'. John, would you revert it? Sorry
for the false alarm.
Thanks,
-yi
Reported-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As follows:
- GET_HW_SPEC is now responsible for setting
priv->{ap,sta}_macids_supported, which are bitmasks of supported
macids for AP and STA mode. (Typically, STA firmware images will
support only one macid, #0, in STA mode, and AP firmware images
will support macids #0-7, in AP mode.)
- Our wiphy ->interfaces_modes is now set based on the non-zero-ness
of these two bitmasks.
- We main priv->macids_used, a bitmask of which macids are currently
in use. ->add_interface() will assign the lowest free macid for
this interface type as it is created, or bail out if there are no
more free macids to assign. ->delete_interface() will mark the
macid as being free again.
This enables the multi-BSS code added in the previous commits.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SET_BEACON, SET_MAC_ADDR, BSS_START and SET_NEW_STN are the currently
supported firmware commands that are actually per-vif commands. Use
mwl8k_post_pervif_cmd() for these commands, so that the macid of the
vif they operate on gets passed down into the firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the bytes in the mwl8k firmware command header is the 'macid'
byte, which for per-vif commands indicates which of the BSSes this
command is intended for. (For commands that are not per-vif commands,
this byte can just be 0.)
This patch adds mwl8k_post_pervif_cmd(), which will take the macid
assigned to this interface (to be done in ->add_interface()), copy it
into the command packet macid field, and post the command as usual.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for adding multi-BSS support.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the decision about whether to register the 2.4 and 5 GHz bands
with mac80211 by looking at the capability field in GET_HW_SPEC (STA
firmware only for now). This enables 5 GHz STA operation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever mac80211 gives us a legacy rate bitmap in the context of the
5 GHz band, we need to remember to shift the bitmap left by 5 positions
before giving it to the firmware, as the firmware follows the bitmap
bit assignment of the 2.4 GHz rate table even if we're on the 5 GHz
band, and the 2.4 GHz rate table includes five non-OFDM rates at the
start that are not valid in the 5 GHz band.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mwl8k firmware uses indices into the 2.4 GHz band rate table for
the receive descriptor channel field even if the packet was received
on a 5 GHz channel, while mac80211 expects an index into the 5 GHz
band rate table when packets are received on the 5 GHz band, which
presents a mismatch as the 5 GHz band rate table lacks the five
non-OFDM rates that the 2.4 GHz rate table starts with.
To handle this properly, we need to substract 5 from the rate index
field if the packet was received on a 5 GHz channel (and was not
received at an MCS rate).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So that we can make 2.4 GHz and 5 GHz band registration conditional
on the capability bitmask returned by the firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for adding 5 GHz band/channels/rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
0x2a43 is a single-band (2.4GHz only) 88w8366 mini-PCIe card.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By storing the sequence counter in << 4 format, like other drivers do.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki