Individual controller driver has different requirement for wakeup
setting, so move it from core to itself. In order to align with
current etting the default wakeup setting is enabled (except for
chipidea host).
Pass compile test with below commands:
make O=outout/all allmodconfig
make -j$CPU_NUM O=outout/all drivers/usb
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most HCD drivers are doing the same thing in their ".shutdown" callback
so it makes sense to use the generic usb_hcd_platform_shutdown()
handler there.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For PHY mode, the PHYs must be brought out of reset
before the EHCI controller is started.
This patch fixes the issue where USB devices are not found
on Beagleboard/Beagle-xm if USB has been started previously
by the bootloader. (e.g. by "usb start" command in u-boot)
Tested on Beagleboard, Beagleboard-xm and Pandaboard.
Issue present on 3.10 onwards.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'omap_ehci_dt_ids' is always compiled in. Hence use of
of_match_ptr is unnecessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many USB host drivers contain code such as:
if (!pdev->dev.dma_mask)
pdev->dev.dma_mask = &tegra_ehci_dma_mask;
... where tegra_ehci_dma_mask is a global. I suspect this code originated
in commit 4a53f4e "USB: ehci-tegra: add probing through device tree" and
was simply copied everywhere else.
This works fine when the code is built-in, but can cause a crash when the
code is in a module. The first module load sets up the dma_mask pointer,
but if the module is removed and re-inserted, the value is now non-NULL,
and hence is not updated to point at the new location, and hence points
at a stale location within the previous module load address, which in
turn causes a crash if the pointer is de-referenced.
The simplest way of solving this seems to be to copy the code from
ehci-platform.c, which uses the coherent_dma_mask as the target for the
dma_mask pointer.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the USB PHY layer never returns NULL we don't need
to check for that condition.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it does almost nothing, get rid of omap_ehci_init()
and move the ehci->caps initialization part into probe().
Also remove the outdated TODO list from header.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move PHY initialization until after EHCI initialization is
complete, instead of initializing the PHYs first, shutting
them down again, and then initializing them a second time.
This fixes HSIC device detection.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even when not in PHY mode, the USB device on the port (e.g. HUB)
might need resources like RESET which can be modelled as a PHY
device. So try to get the PHY device in any case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows the OMAP EHCI controller to be specified via device tree.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is only one resource per type we don't really need
to use resource name to obtain it. This also also makes it easier
for device tree adaptation.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY regulator handling must be done in the PHY driver
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reset GPIO handling for the PHY must be done in the PHY
driver. We use the PHY helpers instead to reset the PHY.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For each port that is in PHY mode we obtain a PHY device using the USB PHY
library and put it out of suspend.
It is up to platform code to associate the PHY to the controller's
port and it is up to the PHY driver to manage the PHY's resources.
Also remove weird spacing around declarations we come across.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of devm_ioremap_resource() and correct comment.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1645) converts ehci-omap over to the new "ehci-hcd is a
library" approach, so that it can coexist peacefully with other EHCI
platform drivers and can make use of the private area allocated at
the end of struct ehci_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation,
OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee Jones. In
particular, the debugfs and the sysct interfaces got extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core
driver, with a much needed module id lookup code improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the palmas
GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and
Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based
devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a better
card detection code path and now also supports the RTS5227 chipset, thanks
to Wei Wang and Roger Tseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BhC1
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
The module alias should be "ehci-omap" and not
"omap-ehci" to match the platform device name.
The omap-ehci module should now autoload correctly.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's have a single platform data structure for the OMAP's High-Speed
USB host subsystem instead of having 3 separate ones i.e. one for
board data, one for USB Host (UHH) module and one for USB-TLL module.
This makes the code much simpler and avoids creating multiple copies of
platform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
For the ehci-omap.c part:
Acked-by: Alan Stern <stern@rowland.harvard.edu>
This is a collection of header file cleanups, mostly for OMAP and AT91,
that keeps moving the platforms in the direction of multiplatform by
removing the need for mach-dependent header files used in drivers and
other places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aggA
-----END PGP SIGNATURE-----
Merge tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
This patch (as1623) removes the ehci_port_power() routine and all the
places that call it. There's no reason for ehci-hcd to change the
port power settings; the hub driver takes care of all that stuff.
There is one exception: When the controller is resumed from
hibernation or following a loss of power, the ports that are supposed
to be handed over to a companion controller must be powered on first.
Otherwise the handover won't work. This process is not visible to the
hub driver, so it has to be handled in ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.
Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit 354ab8567a titled
"Fix OMAP EHCI suspend/resume failure (i693)" is causing
the usb hub and device detection fails in beagle XM
causeing NFS not functional. This affects the core retention too.
The same commit logic needs to be revisted adhering to hwmod and
device tree framework.
for now, this commit id 354ab8567a
titled "Fix OMAP EHCI suspend/resume failure (i693)" reverted.
This patch is validated on BeagleXM with NFS support over
usb ethernet and USB mass storage and other device detection.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac9651: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
The omap_ehci_init() is introduced in the below commit:
commit 1a49e2ac9651df7349867a5cf44e2c83de1046af(EHCI:
centralize controller initialization)
the local variable of 'pdev' inside omap_ehci_init() is used
but not defined, so fix the compiling failure.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1564c) converts the EHCI platform drivers to use the
central ehci_setup() routine for generic controller initialization
rather than each having its own idiosyncratic approach.
The major point of difficulty lies in ehci-pci's many vendor- and
device-specific workarounds. Some of them have to be applied before
calling ehci_setup() and some after, which necessitates a fair amount
of code motion. The other platform drivers require much smaller
changes.
One point not addressed by the patch is whether ports should be
powered on or off following initialization. The different drivers
appear to handle this pretty much at random. In fact it shouldn't
matter, because the hub driver turns on power to all ports when it
binds to the root hub. Straightening that out will be left for
another day.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.
This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.
This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.
The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.
I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.
v3 - Brown paper bag its too early in the morning actually run
git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: Mantesh Sarashetti <mantesh@ti.com>
Tested-by: Mantesh Sarashetti <mantesh@ti.com>
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A recent commit, [PATCH] Fix OMAP EHCI suspend/resume failure
(i693) '354ab856' causes ehci probe to fail on omap3xxx. This
exposed bugs in the ehci_hcd_omap_probe error path causing
an oops.
On the error path, call usb_remove_hcd if usb_add_hcd has been
called, and call usb_put_hcd if usb_alloc_hcd has been called.
Tested on BB-xM.
Signed-off-by: Russ.Dill@ti.com
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Its observed with some PHY, the 60Mhz clock gets
cut too soon for OMAP EHCI, leaving OMAP-EHCI in a bad state.
So on starting port suspend, make sure the 60Mhz clock to EHCI
is kept alive using an internal clock, so that EHCi can cleanly
transition its hw state machine on a port suspend.
Its not proven if this is the issue hit on USB3333,
but the symptoms look very similar.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Volodymyr Mieshkov <x0182794@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PHY reset pin is connected to a GPIO on external GPIO chip
(e.g. I2C), we should not call the gpio_set_value() function, but
gpio_set_value_cansleep().
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0f) created a regression
with Beagleboard xM if booting the kernel after running 'usb start' under u-boot.
Finishing the reset before calling 'usb_add_hcd' fixes the regression. This is most likely due to
usb_add_hcd calling the driver's reset and init functions which expect the hardware to be
up and running.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
The ehci and ohci drivers does not use the APIs of the usbhs
core driver; the runtime pm APIs are used for clock
enable/disable. Since usbhs is parent platform device of the
ehci and ohci devices, the runtime apis indirectly uses the
usb hs core device as input parameter to for clock functions.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the ehci_reset() call done in the ehci_run() routine of the
USB EHCI host controller driver and add an ehci_reset() call to the
probe processing of all EHCI platform drivers that do not already call
ehci_reset().
The call to ehci_reset() from ehci_run() was problematic for several
platform drivers, and unnecessary for others. This change moves the
decision to call ehci_reset() at driver startup to the platform
driver code.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Obviously, disabling & put regulator and iounmap(hcd->regs)
are missed in .remove and failure handling path of .probe,
so add them.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Keshava Munegowda <Keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The two first HC capability registers (CAPLENGTH and HCIVERSION)
are defined as one 8-bit and one 16-bit register. Most HC
implementations have selected to treat these registers as part
of a 32-bit register, giving the same layout for both big and
small endian systems.
This patch adds a new quirk, big_endian_capbase, to support
controllers with big endian register interfaces that treat
HCIVERSION and CAPLENGTH as individual registers.
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in case of ehci phy mode; regulator of phy
should be enabled before initializing the
usbhs core driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Steve Calfee <stevecalfee@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ehci and ohci drivers are simplified; Since
UHH and TLL initialization, clock handling are
done by common usbhs core driver, these functionalities
are removed from ehci and ohci drivers.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Create the ehci and ohci specific platform data structures.
The port enum values are made common for both ehci and ohci.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we have names on all memory bases, we can
switch to use platform_get_resource_byname() which
will make it simpler when we move to a setup where
OHCI and EHCI on OMAP play well together.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The EHCI controller in OMAP4 supports a transceiver-less link
mode (TLL mode), similar to the one in OMAP3. On the OMAP4
however, there are an additional set of clocks that need
to be turned on to get this working.
Request and configure these for each port if that port
is connected in TLL mode.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are a few error paths in ehci_hcd_omap_probe that can be triggered
because of memory allocation or hw failure. Change those dev_dbg error
prints to dev_err with an error code printed so that the end users are able
to notice the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Peter Chen