Now that the backlight device no longer gets registered too early we
should be able to drop most of the INVALID_PIPE checks from the backlight
code.
The only exceptio is the opregion stuff where we may (in theory at
least) get a request from the BIOS already during driver init as soon as
the backlight setup has been done. In which case we can still get the
INVALID_PIPE from intel_get_pipe_from_connector(). So leave that check
in place, and add a comment explaining why.
For the rest, if we still manage to get here with INVALID_PIPE on
VLV/CHV we will now get a WARN from the lower level functions and
can then actually investigate further.
v2: Leave the check in the BIOS related code (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.
That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.
Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.
This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.
v2: Do not lie to the user in the debug prints (Jani)
Include connector name in the prints (Jani)
Fix a typo in the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV when the display is off, we can't read out the current
backlight level from the hardware since we have no pipe to do so.
Currently we end up reading a bigus register due to passing
INVALID_PIPE to VLV_BLC_PWM_CTL().
Skip the entire .get_backlight() call if the backlight isn't enabled
according to backlight.enabled.
This problem can be reproduced simply by reading the backlight device
actual_brightness file while the display is off.
Cc: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have backlight controls only on pipes A and B. Bail out
without touching registers that don't exist, and print a warning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SPT is always in the PCH override mode, and the bit MBZ. Only set
override on LPT.
v2: check for PCH version (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I've sent the first pull request to Dave and I expect his request
for a merge tree any second now ;-)
More seriously I have some pending patches for 3.19 that depend upon
both trees, hence backmerge. Conflicts are all trivial.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
v2: Of course I've forgotten the fixup script for the silent conflict.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Move the duplicated DIV_ROUND_CLOSEST_ULL macro into the intel_drv.h
header file so that it can be shared between intel_display.c
and intel_panel.c.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Reviewed-By: Joe Konno <joe.konno@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Improper truncated integer division in the scale() function causes
actual_brightness != brightness. This (partial) work-around should be
sufficient for a majority of use-cases, but it is by no means a complete
solution.
TODO: Determine how best to scale "user" values to "hw" values, and
vice-versa, when the ranges are of different sizes. That would be a
buggy scenario even with this work-around.
The issue was introduced in the following (v3.17-rc1) commit:
6dda730 drm/i915: respect the VBT minimum backlight brightness
Note that for easier backporting this commit adds a duplicated macro.
A follow-up cleanup patch rectifies this for 3.18+
v2: (thanks to Chris Wilson) clarify commit message, use rounded division
macro
v3: -DIV_ROUND_CLOSEST() fails to build with CONFIG_X86_32=y. (Jani)
-Use DIV_ROUND_CLOSEST_ULL() instead. (Damien)
-v1 and v2 originally authored by Joe Konno.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Cc: stable@vger.kernel.org
Reviewed-By: Joe Konno <joe.konno@intel.com>
[danvet: Add backporting note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Originally the irq safe spinlock was required because of asle
interrupts. But since
commit 91a60f2071
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Oct 31 18:55:48 2013 +0200
drm/i915: move opregion asle request handling to a work queue
there's no need for this any more. So switch to the simpler mutex.
v2: Cite the right commit, spotted by Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
Chris has decided that enough is enough. It's time to fixup dev Vs
dev_priv. This is a modest contribution to the crusade.
v2: Still use INTEL_INFO(), for the (mythical!) case we want to hardcode
the info struct with defines (Chris)
Rename the macro argument from 'dev' to 'dev_priv' (Jani)
v3: Use names unlikely to be used as macro arguments (Chris)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make backlight class sysfs brightness 0 value switch off the backlight
for connectors that have the backlight_power callback defined. For eDP,
this has the similar caveats regarding power savings as bl_power as only
the power sequencer backlight control is switched off.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make backlight class sysfs bl_power a sub-state of backlight enabled, if
a backlight power connector callback is defined. It's up to the
connector callback to handle the sub-state, typically in a way that
respects panel power sequencing.
v2: Post the version that does not oops. *facepalm*.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Tested_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS or firmware can modify hardware state during suspend/resume,
for example on the Toshiba CB35 or Lenovo T400, so log a debug message
instead of a warning if the backlight is unexpectedly enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80930
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Historically we've exposed the full backlight PWM duty cycle range to
the userspace, in the name of "mechanism, not policy". However, it turns
out there are both panels and board designs where there is a minimum
duty cycle that is required for proper operation. The minimum duty cycle
is available in the VBT.
The backlight class sysfs interface does not make any promises to the
userspace about the physical meaning of the range
0..max_brightness. Specifically there is no guarantee that 0 means off;
indeed for acpi_backlight 0 usually is not off, but the minimum
acceptable value.
Respect the minimum backlight, and expose the range acceptable to the
hardware as 0..max_brightness to the userspace via the backlight class
device; 0 means the minimum acceptable enabled value. To switch off the
backlight, the user must disable the encoder.
As a side effect, make the backlight class device max brightness and
physical PWM modulation frequency (i.e. max duty cycle)
independent. This allows a follow-up patch to virtualize the max value
exposed to the userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 773875bfb6.
It is very much needed and the lack of dithering has been reported by
a large list of people with various gen2/3 hardware.
Also, the original patch was complete non-sense since the WARNING
backtraces in the references bugzilla are about
gmch_pfit.lvds_border_bits mismatch, not at all about the dither bit.
That one seems to work.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
caused a regression on machines with a misconfigured VBT. Add a quirk to
assert the presence of a controllable backlight. Use it to ignore the VBT
backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For reasons I can't claim to fully understand gen4 seems to require
backlight duty cycle setting after the backlight has been enabled, or
else black screen follows. I don't have documentation for the correct
sequence on gen4 either. Confirmed on Dell Latitude D630 and MacBook4,1.
This fixes a regression introduced by
commit b35684b8fa
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:13:41 2013 +0200
drm/i915: do full backlight setup at enable time
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75791
Reported-and-tested-by: mcy@lm7.fr
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79423
Reported-and-tested-by: Marc Milgram <mmilgram@redhat.com>
Cc: Stable <stable@vger.kernel.org> # 3.14+
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Merge drm-fixes into drm-next.
Both i915 and radeon need this done for later patches.
Conflicts:
drivers/gpu/drm/drm_crtc_helper.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/i915_gem_gtt.c
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Somehow a few functions have been dropped in the middle of backlight
code. Move them around. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we set backlight on behalf of ACPI opregion, we will convert the
backlight value in the 0-255 range defined in opregion to the actual
hardware level. Commit 22505b82a2 (drm/i915: avoid brightness overflow
when doing scale) is meant to fix the overflow problem when doing the
conversion, but it also caused a problem that the converted hardware
level doesn't quite represent the intended value: say user wants maximum
backlight level(255 in opregion's range), then we will calculate the
actual hardware level to be: level = freq / max * level, where freq is
the hardware's max backlight level(937 on an user's box), and max and
level are all 255. The converted value should be 937 but the above
calculation will yield 765.
To fix this issue, just use 64 bits to do the calculation to keep the
precision and avoid overflow at the same time.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=72491
Reported-by: Nico Schottelius <nico-bugzilla.kernel.org@schottelius.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
Apparently we really only need this when the pfit is enabled, at least
I couldn't dicern any difference here. Furthermore the hacks we have
to reconstruct this bit is a bit glaring, and probably only works
because we can't move the lvds port to any other pipe than pipe B on
gen2/3.
So let's just rip this out.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77137 (the LVDS
WARNING log, not the main "VGA can't be turned on" issue).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some machines use an external EC for controlling the backlight. Info
about this is present in the VBT. Do not setup native backlight control
if no PWM backlight is available or supported according to VBT. The
acpi_backlight interface appears to work for the EC control.
In most cases there has been no harm done, but it looks like there are
machines out there that have both an EC and our PWM line connected to
the same wire. This, obviously, does not end well.
This should fix the regression caused by
commit bc0bb9fd1c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:14:29 2013 +0200
drm/i915: remove QUIRK_NO_PCH_PWM_ENABLE
AFAICT the quirk removed by the above commit effectively resulted in
i915 not driving the backlight PWM output, thus not messing things up.
Additionally this should fix the regression caused by
commit fbc9fe1b4f
Author: Aaron Lu <aaron.lu@intel.com>
Date: Fri Oct 11 21:27:45 2013 +0800
ACPI / video: Do not register backlight if win8 and native interface exists
which left some machines without a functioning backlight interface.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76276
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=62281
CC: Aaron Lu <aaron.lu@intel.com>
CC: Eric Griffith <EGriffith92@gmail.com>
CC: Kent Baxley <kent.baxley@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTJlUvAAoJEHm+PkMAQRiGOhYH/1I+Bc7N7Rjr6QQAtBIy0GPC
XMqSE/gpgxlvRneQbQsvTUlPnWRhgzLGendT9HFKawkaQ0UNuZdRVyBHGFmpuED8
RlbicVVuuEZabrxEnCd7UPvYvEyK5pLIFpCRs5B+ManB1qLki2Ar03ymH1NRxOde
edmPbSUFo2aONITrEBm7tqT3cShTmBaDGP/zU0TNDMNrpVVDbHZolSNu2z4xOTa5
GqAOEbluLQ6jP3yxWur/V3Lk3W7pB6TabfX4o6UZu0F3iFnJxRMIzHXrI3o4yLTj
HEwmB3npfc8DIUk4oik7RkN+aqxDcdg/rBLQD63+xxt6zCkP+0q16brC0R67qWE=
=n9Ml
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc7' into drm-next
Linux 3.14-rc7
Backmerge to help out Intel guys.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915gm and i945gm also seem to use and need the legacy combination mode
bit in BLC_PWM_CTL.
v2: Also do this for i915gm (Ville).
Reported-and-tested-by: Luis Ortega <luiorpe1@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75001
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Instead of modifying intel_panel in lvds_init_connector/dsi_init/
edp_init_connector, making changes to move intel_panel->downclock_mode
initialization to intel_panel_init()
v2: Jani's review comments incorporated
Removed downclock_mode local variable in dsi_init and
edp_init_connector
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.
Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".
The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:
$ git grep "i915\." -- drivers/gpu/drm/i915
v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was forgotten in
commit 565ee3897f
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 13 12:56:29 2013 +0200
drm/i915: do not save/restore backlight registers in KMS
Since the confusion was likely due to the duplicated definition for
this pci config register, let's unify that, too.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My 855gm doesn't register the intel backlight but it still ends up
calling the backlight code to enable/disable the backlight via the
LVDS code. This leads to some WARNs due to backlight.max being 0.
Let's have intel_panel_enable_backlight() and intel_panel_disable_backlight()
check whether there's a backlight present or not.
Also move the backlight.present check from asle_set_backlight() into
intel_panel_set_backlight() for some extra symmetry.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are needed when we cat the debugfs and sysfs files.
V2: - Rebase
V3: - Rebase
V4: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If one mode of a internal panel has more than one refresh rate, then a reduced
clock is found for the LFP (LVDS/eDP). This enables switching between low
and high frequency dynamically. Moving downclock calculation to intel_panel
so that it is common for LVDS and eDP.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge the bdw changes into the backlight rework branch so that we can
adapt the new code for bdw, too. This is a bit a mess, but doing this
another way would have delayed the merging of the backlight
refactoring. Mea culpa.
As discussed with Jani on irc only do bdw-specific callbacks for the
set/get methods and bake in the only other special-case into the pch
enable function.
Conflicts:
drivers/gpu/drm/i915/intel_panel.c
v2: Don't enable the PWM too early for bdw (Jani).
v3: Create new bdw_ functions for setup and enable - the rules change
sufficiently imo with the switch from controlling the pwm from the cpu
to controlling it completel from the pch to warrant this.
v4: Rip out unused pipe variable in bdw_enable_backlight (0-day
builder).
Tested-by: Ben Widawsky <ben@bwidawsk.net> (on bdw)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No longer needed. We now have fully cached max backlight values.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The quirk was added as what I'd say was a stopgap measure in
commit e85843bec6
Author: Kamal Mostafa <kamal@canonical.com>
Date: Fri Jul 19 15:02:01 2013 -0700
drm/i915: quirk no PCH_PWM_ENABLE for Dell XPS13 backlight
without really digging into what was going on.
Also, as mentioned in the related bug [1], having the quirk regressed
some of the machines it was supposed to fix to begin with, and there
were patches posted to disable the quirk on such machines [2]!
The fact is, we do need the BLM_PCH_PWM_ENABLE bit set to have
backlight. With the quirk, we've relied on BIOS to have set it, and our
save/restore code to retain it. With the full backlight setup at enable,
we have no place for things that rely on previous state.
With the per platform hooks, we've also made a change in the PCH
platform enable order: setting the backlight duty cycle between CPU and
PCH PWM enable. Some experimenting and
commit 770c12312a
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Aug 11 08:56:42 2012 +0200
drm/i915: Fix blank panel at reopening lid
indicate that we can't set the backlight before enabling CPU PWM; the
value just won't stick. But AFAICT we should do it before enabling the
PCH PWM.
Finally, any fallout we should fix properly, preferrably without quirks,
and absolutely without quirks that rely on existing state. With the per
platform hooks have much more flexibility to adjust the sequence as
required by platforms.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=47941
[2] http://lkml.kernel.org/r/1378229848-29113-1-git-send-email-kamal@canonical.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should now have all the information we need to do a full
initialization of the backlight registers.
v2: Keep QUIRK_NO_PCH_PWM_ENABLE for now (Imre).
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prior to Haswell the CPU control register for backlight
(BLC_PWM_CPU_CTL) toggled the PCH baclight pin for us. This made some
sense as there was no pin on the CPU. With Haswell came the introduction
of a CPU backlight pin, but the interface was still controlled by
software with the same mechnism. Behind the scenes, hardware did all the
dirty work for us.
Broadwell no longer provides this for free. If we want to use the PCH
backlight pin [1] then we have to set the override bit BLC_PWM_PCH_CTL1
and program BLC_PWM_PCH_CTL2 for the PWM values.
This patch implements that. This patch is compile tested only, and given
that I rarely if ever touch this code, careful review is welcome.
[1] According to Art, we know of no devices that exist which use the CPU
pin (and remember it has existed already on HSW). If such a device does
exist, we'll have to handle it properly - this is left as TODO until
then.
v2: Drop the abstraction prep patch, as a bigger backlight overhaul is
in the works, and do just the mimimal bdw enabling now. (by Jani)
CC: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prepare for being able to use the information at enable.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now have the max backlight value cached. Use it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows more flexibility in the ordering of the register writes, and
lets us drop level setting altogether as necessary on a per platform
basis.
For gen2-gen3, this is the only thing that happens in enable/disable.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It has per pipe registers.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä