Try to send to correct address this time!
---------- Forwarded Message ----------
Subject: [PATCH] Fix cdc-phonet build
Date: Saturday 23 Jul 2011
From: Chris Clayton <chris2553@googlemail.com>
To: linux-net@vger.kernel.org
cdc-phonet does not presently build on linux-3.0 because there is no entry for it in
drivers/net/Makefile. This patch adds that entry.
Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not? To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>
I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are. The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...
Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init
Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.
Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.
This was reported and based on work by Takuma Umeya. I also verified
the problem and tested that this fix resolves it.
V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.
I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.
V3: Actually sending the proper patch....
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Takuma Umeya <tumeya@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 87c288c6e9 "gianfar: do vlan cleanup" has two issues:
# permutation of rx and tx flags
# enabling vlan tag insertion by default (this leads to unusable connections on some configurations)
If VLAN insertion is requested (via ethtool) it will be set at an other point ...
Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
wldev is freed in b43_one_core_detach() and should not be accessed after
that call. Keep wldev->dev in a local variable.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've fixed the last issue with BCMA support which caused memory
corruption on loading and unloading b43. Support for BCMA in b43 was
tested with 14e4:4353, 14e4:4357, 14e4:4727 and 14e4:4331. First two
cards (BCM43224 and BCM43225) are supported.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take Eric's patch one step further.
Use netdev_skb_ip_align to do setup the receive skb.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
This patch includes:
- Counting statistics ramrods as EQ ramrods the way they should be. This
accounting is meant to prevent MC asserts in case of software bugs.
- Fixes in debug facilities which were added while working on one of such
bugs.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fixes minor formatting in that function.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a result of DCBX negotiation some priorities maybe untouched and still
unmapped to any COS; instead of sending them to COS0 we assign them
to the same COS as L2 traffic - to avoid collisions with storage class of
service.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/via-velocity.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/qlge/qlge_main.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/igb/igb_main.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/can/c_can/c_can.c
drivers/net/can/c_can/c_can_platform.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated #include('s) in
drivers/net/bna/bnad.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Consolidated bfa_sm.h and bfa_wc.h into bfa_cs.h
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Heartbeat failure counter is not incrementing under some scenarios.
Update hbfails and hb_count stats during hwerror event.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Added logic to unlock hw semaphore if the previos FW boot was from boot
code (flash based) and the current FW initialization attempt is from OS
driver.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Changed event name IOC_E_PFAILED to IOC_E_PFFAILED
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- If there is a command pending in the mailbox, bfa_ioc_mbox_queue() enqueues
the mailbox command to a pending command queue. Entries in this queue are
not flushed when IOC is disabled. As a result, when IOC is re-enabled again,
the stale entries in the pending command queue are posted to the mailbox.
When these mailbox commands are processed by the FW and responses are sent,
unexpected events are received by other modules' FSMs (f.e. bfa_msgq) which
have not posted any mailbox commands after IOC was enabled.
- Flush the pending mailbox command queue when IOC is disabled. Rename
bfa_ioc_mbox_hbfail to bfa_ioc_mbox_flush. Call bfa_ioc_mbox_flush
from bfa_iocpf_sm_disabled_entry()
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Always set mbox irq index to zero and make corresponding changes in mbox
irq alloc/sync function and txrx irq index calculation. Add definition of
BNAD_INTX_TX_IB_BITMASK & BNAD_INTX_RX_IB_BITMASK and update
bnad_txrx_irq_alloc accordingly.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chnage details:
- The module name is not used in case of state machine fault, hence no longer
passing the module name to the fault handler.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Replace IOC HB failure event notification with a more generic mechanism
that is capable of sending enble, disable, and failed events to registered
modules. As a result, cee module event handling callback bfa_cee_hbfail()
is replaced with bfa_cee_notify() so that it can receive and handle
different events from IOC.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Driver cleanup as per new checkpatch v0.31
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Print the dirver version when module is loaded.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver reads PCI subsystem ID from the PCI configuration register while it's
already stored by the PCI subsystem in the 'subsystem_device' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
IB/qib: Defer HCA error events to tasklet
mlx4_core: Bump the driver version to 1.0
RDMA/cxgb4: Use printk_ratelimited() instead of printk_ratelimit()
IB/mlx4: Support PMA counters for IBoE
IB/mlx4: Use flow counters on IBoE ports
IB/pma: Add include file for IBA performance counters definitions
mlx4_core: Add network flow counters
mlx4_core: Fix location of counter index in QP context struct
mlx4_core: Read extended capabilities into the flags field
mlx4_core: Extend capability flags to 64 bits
IB/mlx4: Generate GID change events in IBoE code
IB/core: Add GID change event
RDMA/cma: Don't allow IPoIB port space for IBoE
RDMA: Allow for NULL .modify_device() and .modify_port() methods
IB/qib: Update active link width
IB/qib: Fix potential deadlock with link down interrupt
IB/qib: Add sysfs interface to read free contexts
IB/mthca: Remove unnecessary read of PCI_CAP_ID_EXP
IB/qib: Remove double define
IB/qib: Remove unnecessary read of PCI_CAP_ID_EXP
...
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are only two capabilities we need, and both are trivial to find.
ath5k_hw_hasbssidmask() is true on AR5212, but not on AR5210 or AR5211.
ath5k_hw_hasveol() is true on AR5211 and AR5212, but not on AR5210,
according to the HAL source.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove b43's workarounds at the same time. Other users of
ssb_dma_translation do not support any 64-bit DMA devices, so they are
not affected.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Analyze of MMIO dumps from BCM43224, BCM43225, BCM4313 and BCM4331 has
shown that wl disables parity check for all that cards. This is required
for receiving any packets from the hardware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some workloads need some headroom (NET_SKB_PAD) to avoid expensive
reallocations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Private rx_csum flags are now duplicate of netdev->features &
NETIF_F_RXCSUM. We remove those duplicates and now use the net_device_ops
ndo_set_features. This was based on the original patch submitted by
Michal Miroslaw <mirq-linux@rere.qmqm.pl>. I also removed the special
case not requiring a reset for X540 hardware. It is needed just as it is
in 82599 hardware.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Martin Wilck <martin.wilck@ts.fujitsu.com> reported that systems using
the ixgbe-driver that were capable of WoL were rebooting almost as soon
as they were shut down. This is because the default WoL settings
enabled magic packet, broadcast, unicast, and multicast.
Other Intel devices seem to use the stored eeprom value for initial WoL
capabilities. The 82578DM (e1000e) and 82576 (igb) the devices I looked
at had only the magic packet enabled in the eeprom, so that seems
appropriate on ixgbe-based devices as well. I set the WoL options on my
82578DM to be the same default as the ixgbe devices (umbg) and saw the
same as Martin -- almost as soon as my box shutdown, it booted again.
This patch changes the default to only be the magic packet. This is the
same as the default for most Intel and non-Intel hardware currently
upstream.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Martin Wilck <martin.wilck@ts.fujitsu.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to address possible race conditions from the status
and error bits on the RX descriptors being re-read by multiple functions in
the RX cleanup path. To resolve this I have added code that will pass the
staterr value to those functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves work_limit, total_packets, and total_bytes into the ring
container struct of the q_vector. The advantage of this is that it should
reduce the size of memory used in the event of multiple rings being
assigned to a single q_vector. In addition it should help to reduce the
total workload for calculating itr since now total_packets and total_bytes
will be the total work done of the interrupt instead of for the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for a ring container structure to be used within
the q_vector. The basic idea is to provide a means of separating the RX
and TX rings while maintaining a common structure for their containment.
The advantage to this is that later we should be able to pass this
structure to the update_itr functions without needing to pass individual
rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many features were added to this driver, so the driver version should change too.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The ixgbe_maybe_stop_tx function is only a few lines long and is called
multiple times through the xmit hotpath. In order to streamline things it
makes sense to just inline it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to update ATR so that it will use the recorded RX
queue instead of the CPU in the case of routing. This change is meant to
help ixgbe default behavior to more closely match that of the kernel.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On this chipset it is required to configure the MPHY block for loopback tests. If MPHY is not configured then all loopback tests will report failures.
Signed-off-by: Robert Healy <robert.healy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Interrupts about link lost or rx sequence errors are not reported by
the ce4100 hardware, leading to transitions from link UP to link DOWN
never being reported.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
o Minimum fw version supported for P3 chip is 4.0.505
o File Fw > 4.0.554 is not supported if flash fw < 4.0.554.
o In mn firmware case, file fw older than flash fw is allowed.
o Change variable names for readability
o Update driver version 4.0.76
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently be3-native mode is requested only in probe(). It must be requested, each time the card is reset either after an EEH error or after
sleep/hibernation.
Also, the be_cmd_check_native_mode() is better named be_cmd_req_native_mode()
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a panic in virtnet_remove. unregister_netdev has already
freed up the netdev (and virtnet_info) due to dev->destructor
being set, while virtnet_info is still required. Remove
virtnet_free altogether, and move the freeing of the per-cpu
statistics from virtnet_free to virtnet_remove.
Tested patch below.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function can_get_bittiming is not used anywhere else, so it should be
static.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HIGHDMA is being disabled even when dma64 is true. This patch fixes it.
CC: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parent device for netdev should be set before netdev_info() can be called
otherwise there is a NULL pointer dereference and probe() fails.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
This device can be found in Acer Iconia TAB W500 tablet dock.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change, most PHY configuration parameters were passed
into the STMMAC device as a separate PHY device. As well as being
unusual, this made it difficult to make changes to the MAC/PHY
relationship.
This patch moves all the PHY parameters into the MAC configuration
structure, mainly as a separate structure. This allows us to completely
ignore the MDIO bus attached to a stmmac if desired, and not create
the PHY bus. It also allows the stmmac driver to use a different PHY
from the one it is connected to, for example a fixed PHY or bit banging
PHY.
Also derive the stmmac/PHY connection type (MII/RMII etc) from the
mode can be passed into <platf>_configure_ethernet.
STLinux kernel at git://git.stlinux.com/stm/linux-sh4-2.6.32.y.git
provides several examples how to use this new infrastructure (that
actually is easier to maintain and clearer).
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch removes the following serie of warnings
when the driver is compiled as built-in:
drivers/net/stmmac/stmmac_main.c: In function stmmac_cmdline_opt:
drivers/net/stmmac/stmmac_main.c:1855:12: warning: ignoring return
value of kstrtoul, declared with attribute warn_unused_result
[snip]
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the missing dma_unmap().
Which solved the critical issue of system freeze on heavy load.
Michal Miroslaw's rejected patch:
[PATCH v2 10/46] net: jme: convert to generic DMA API
Pointed out the issue also, thank you Michal.
But the fix was incorrect. It would unmap needed address
when low memory.
Got lots of feedback from End user and Gentoo Bugzilla.
https://bugs.gentoo.org/show_bug.cgi?id=373109
Thank you all. :)
Cc: stable@kernel.org
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_vlan_rx_register is no longer in use in any driver so remove it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when all devices are cleaned up, bond can be cleaned up as well
- remove bond->vlgrp
- remove bond_vlan_rx_register
- substitute necessary occurences of vlan_group_get_device
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- kill priv->vlgrp and stmmac_vlan_rx_register (used for nothing :))
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill vdev->vlgrp and vxge_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlgrp and igb_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill np->vlangrp and nv_vlan_rx_register
- allow to turn on/off rx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlgrp and e1000_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill pi->vlan_grp and vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atl2_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atlx_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill dev->vlgrp and ns83820_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill np->vlgrp and netdev_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill vptr->vlgrp and velocity_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlgrp and ixgbevf_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill priv->vlgrp and bdx_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill sp->vlgrp and s2io_vlan_rx_register and s2io_vlan_rx_kill_vid
(which does nothing and is never called :))
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan path
- kill qdev->vlgrp and qlge_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan path
- kill priv->vlgrp and mlx4_en_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill jme->vlgrp and jme_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlgrp and igbvf_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill priv->vlgrp and gfar_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill enic->vlan_group and enic_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill pi->vlan_grp and cxgb4vf_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlan_grp and t1_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill bnad->vlan_grp and bnad_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atl1e_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill adapter->vlgrp and atl1c_vlan_rx_register
- allow to turn on/off rx/tx vlan accel via ethtool (set_features)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill lp->vlgrp and amd8111e_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- unify vlan and nonvlan rx path
- kill port->vgrp and ehea_vlan_rx_register
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so that ethtool -i will display it correctly on big endian systems.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2fc driver needs to handle netdev events on VLAN devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, the firmware will not respond and we'll have to wait for
timeout. Refactor the wait loop we already have into a separate
function for this purpose.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include FCoE CID space only for E2_PLUS devices. Remove old CID
offset adjustments that are no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes NVRAM selftest failures for 5720 devices by fixing the
checksum area size.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer VPD datablocks can exceed the size the tg3 driver is traditionally
used to. This can cause some of the routines that operate on the VPD
data to fail when in-fact they could have succeeded had they known the
correct size. This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes interrupt selftest failures for recent devices (57765,
5717, 5718. 5719, 5720) by disabling MSI one-shot mode and applying the
status tag workaround to the selftest code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current RSS indirection table is populated such that more traffic
will hit the first RSS ring. This patch adjusts the indirection table
so that the load is more evenly distributed.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5719 and the 5720 to the list of devices that are
EEE capable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally, when the network cable is removed after a successful
autonegotiation, the device will not send a link down interrupt to the
driver. This happens because of a bad interaction of an EEE
workaround. The fix is to adjust the code so that the root cause
condition does not happen.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the scope of the EEE interoperability workaround
to include more asic revisions. The workarond value is tuned to
workaround a link flap issue at 100Mbps.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f2096f94b5, entitled
"tg3: Add 5720 H2BMC support", needed to add code to preserve some bits
set by firmware. Unfortunately the new code causes throughput to stop
after a chip reset because it enables state machines before they are
ready. This patch undoes the problematic code. The bits will be
restored later in the init sequence.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes both the failure in the self-test on 578xx
and a hole in a parity recovery flow that this failure
has discovered:
- internal 'pending' state in a VLAN_MAC object wasn't been cleared
when the object state change was called with DRV_ONLY flag, which in
particular happens when a parity error happens during the self-test.
- bp->sp_state wasn't cleared in the similar circumstances as described
above.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the parity errors recovery flow for 578xx:
- Add a separate column for the 578xx in the parity mask
registers DB.
- Fix the bnx2x_process_kill_chip_reset() to handle the blocks
newly introduced in the 578xx.
Cover ATC and PGLUE_B blocks for 57712 and 578xx.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read FIP MAC address from SHMEM's "port" section
similar to what we do in a MF mode when we read it from
a "func" section of SHMEM.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers dump code erroneously treated 578xx as 57712.
This patch fixes the above and also removes unused data
structures.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current logging styles.
Add pr_fmt where appropriate.
Remove now unnecessary prefixes from printks.
Convert hard coded prefix to __func__.
Add a missing "\n" to a format.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices (e.g. Ubiquiti AirRouter) ship with broken EEPROM chainmask
data, which breaks the initial calibration after a hardware reset.
To fix this, mask the eeprom chainmask with the chainmask of the chip,
and use the chip chainmask if the result is zero.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the auto deep sleep mode has been enabled at driver init time
we should disable it at driver unloading to shutdown the function
gracefully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should consider current packet length also while checking
Tx aggregation buffer room.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For ad-hoc mode, RA is created for each peer connected. In case of
multicast traffic new RA will be created for each multicast
address. While processing Tx packets we have to go through this
RA list. We can avoid some RA nodes by sharing same RA for both
multicast and broadcast packets.
Therefore "memset(0xff)" is used to treat multicast packet as broadcast
one while choosing RA.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is since my patch:
iwlagn: introduce transport layer and implement rx_init
The IRQ is requested before the locks are initialized, hence the crash.
Initialize the tasklet before we request the IRQ on the way.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We now have iwlagn_set_dynamic_key() and
iwl_set_dynamic_key() which is confusing,
rename the former to iwlagn_send_sta_key()
to better reflect what it does -- it only
sends a command and doesn't change driver
state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Sometimes, when mac80211 changes the beacon
interval or when it isn't yet set in mac80211
before association, the uCode will sysassert
because we send it confusing RXON timing vs.
PAN parameters. To fix this, track the last
beacon interval sent to the device and use
that in PAN parameter calculations.
This fixes a bug during P2P group formation
as a client (and possibly association to a
regular AP) while connected to another AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Implement WoWLAN support in iwlagn. The device
supports a number of wakeup triggers and can do
GTK rekeying when asleep (if HW crypto is used).
Unfortunately, we need to disconnect from the AP
after resume since we can't yet get all the info
out of the wowlan uCode to stay connected safely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
As I just discovered while doing WoWLAN, HW crypto
is done wrong for GTKs: they should be programmed
for the AP station ID (in the managed mode case)
and the HW can actually deal with multiple group
keys per station as well (which is useful in IBSS
RSN but that I've chosen not to use this).
To fix all this, modify the way keys are sent to
the device and key offsets are allocated. After
these changes, key offsets are stored into the
hw_key_idx which we can then track for the key
lifetime, not relying on our sta_cmd array. WEP
default keys get special treatment, of course.
Additionally, since I had the API for it, we can
now pre-fill TKIP phase 1 keys for RX now that we
can obtain the P1K from mac80211, a capability I
had added for WoWLAN initially.
Finally, some keys simply don't need to be added
into the device's key cache -- a key that won't
be used for RX is only needed in the TX header,
so "pretend" to have accepted any key without
adding it into the device -- no need to use up
key space there for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
It seems that due to merge issues between different
trees or so this function prototype wasn't removed
when it should have been, do it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn keeps a copy of key stuff internally but
never actually uses it, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move tm_fixed_rate inside CONFIG_IWLWIFI_DEVICE_SVTOOL and only
available when the option is enable.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
WoWLAN may need the NIC even after suspend. One should not do anything to the
NIC in the bus level, since one cannot check whether WoWLAN is enabled or not.
Same for resume.
Add a simple comment to the code to warn about this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The price to pay is the access to the log system. Therefore logs from bus layer
are sent by dev_printk instead of IWL_XXXX.
Rename bus->priv to bus->drv_data to make the separation even clearer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Call iwl_probe with a ready iwl_bus struct. This means that the bus layer
assigns the irq, dev and iwl_bus_ops pointers to iwl_bus before giving it to
iwl_probe.
The device specific struct is allocated together with the common iwl_bus struct
by the bus specific layer. The pointer to the aggregate struct is passed to the
upper layer that holds a pointer to iwl_bus instead of an embedded iw_bus.
The private data given to the PCI subsystem is now iwl_bus and not iwl_priv.
Provide bus_* inliners on the way in order to simplify the syntax.
Rename iwl-pci.h -> iwl-bus.h since it is bus agnostic and represent the
external of the bus layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
It still holds a pointer to iwl_priv. But hopefully this will disappear at some point.
Also add the multiple inclusion protection to iwl-trans.h that was forgotten.
Move iwl-trans structures to iwl-trans.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This function is really related to the transport layer - move it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Basically all the nic_init flow should be in the transport layer.
iwl_prepare_card_hw will move to the transport too in a separate patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All the configurations of the HW for AMPDU are now in the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since iwlagn_setup_deferred_work is always called, fold it into
iwl_setup_deferred_work. BT related works are setup by the new
bt_setup_deferred_work lib_ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
Since iwlagn_rx_handler_setup is always called, fold it into
iwl_rx_handler_setup. BT related handlers are setup by the new
bt_rx_handler_setup lib_ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
kick_nic means to remove the RESET bit from the embedded CPU
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, the mesh was running whenever the appropriate hardware
and firmware was present.
Now we only run the mesh when the interface is running.
Also simplifies interface management a little.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused blindlist code.
Mark a few items const and static where possible. Involved some
code re-ordering, but no code changes.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Luis R. Rodriguez" <lrodriguez@atheros.com>
Cc: ath9k-devel@lists.ath9k.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both ath5k_hw and ath5k_softc represent one instance of the hardware.
This duplication is historical and is not needed anymore.
Keep the name "ath5k_hw" for the merged structure and "ah" for the
variable pointing to it. "ath5k_hw" is shorter than "ath5k_softc", more
descriptive and more widely used.
Put the combined structure to ath5k.h where the old ath5k_softc used to
be. Move some code from base.h to ath5k.h as needed.
Remove memory allocation for struct ath5k_hw and the corresponding error
handling. Merge iobase and ah_iobase fields.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the newer Broadcom chipsets have longe names like BCM43224,
BCM43225, etc. However Broadcom decided to keep using u16 for storing
them. Use %X or %d depending on chip_id value to avoid BCMA8D8, etc.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old masks were causing ugly, delayed lock ups.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following operation was incorrectly translated:
radio_read(0x0011) -> 0xffff
radio_write(0x0011) <- 0xfff7
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also change the default channel to 11. This is the first channel closed
driver switches to.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCMA_IOCTL is register in agent (AKA wrapper) core, we need to use
special R/W ops for it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
create DCB related states in function state-machine
allow handling of DCB errors from FW
allow disablement of DCB in FW, when peer disappears or error
clean up unused functions/variables as pointed by
David Binderman <dcb314@hotmail.com>
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may take some time to cnic to respond, this prevents tx_timeout
when it happens.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e542a2269f (r8169: adjust the RxConfig settings)
broke the return from promiscuous mode to physical address match mode.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Signed-off-by: Hayes Wang <hayeswang@realtek.com>
ConnectX devices support a set of flow counters that can be attached
to a set containing one or more QPs. Each such counter tracks receive
and transmit packets and bytes of these QPs. This patch queries the
device to check support for counters, handles initialization of the
HCA to enable counters, and initializes a bitmap allocator to control
counter allocations. Derived from patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Query another dword containing up to 32 extended device capabilities
and merge it into struct mlx4_caps.flags. Update the code that
handles the current extended device capabilities (e.g UDP RSS, WoL,
vep steering, etc) to use the extended device cap flags field instead
of a field per extended capability. Initial patch done by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The latest firmware adds a second dword containing more device flags,
so extend the device capabilities flags field from 32 to 64 bits.
Derived from patch by Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use all that functions by pointers only. This forces compiler to
create additional duplicated functions that are not inline.
Noticed by Michael in similar bcma code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harshal Chhaya discovered during network tests, that
several of his clients dropped-off the network. The
captured packets shows that the beacons sent by the
AP are at a much lower power than the other data
packets.
The reason for this mishap: The driver never updated
the beacon phy register, so all beacons were always
sent at the lowest power.
Reference: http://marc.info/?l=linux-wireless&m=131067225105801
Reported-by: Harshal Chhaya <harshal@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* reserves feature bit for CCA counters
* extends hardware register file definitions
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marek Vasut