Update the scan command to use the new fw api
(fw 6/7.3.0.0.75).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The device role is a special role used for rx and tx frames
prior to association (as the STA role can get packets only
from its associated bssid)
Since this role is required for the sta association process,
we enable it when a new sta interface is created.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
According to the new multi-role flow, we have to enable the
role before using (starting) it, and disable it on cleanup
(after it's no longer needed).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Change the commands and events according to the new fw api
(fw >= 6/7.3.0.0.75).
The main change is the replacement of JOIN/DISCONNECT commands,
with ROLE_START/ROLE_STOP commands.
The use of these commands should be preceded by the ROLE_ENABLE
command (allocating role resources), and followed by the
ROLE_DISABLE command (freeing role resources).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the acx commands according to the new fw api
(fw >= 6/7.3.0.0.75).
The main change in most of the ACXs is the addition
of a new role_id/link_id field, which is required
for multi-role operation.
Currently, we don't really support multi-role, as
most of our data (inside wl) is global.
As the current fw doesn't support concurrent roles
yet, keep it this way and add wl->role_id and
wl->sta_hlid to save the active role/link.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the fw status struct according to the new fw api
(fw >= 6/7.0.0.35).
All the roles use the same struct now.
The memory accounting was changed a bit according to
the struct changes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new fw doesn't support rx_filtering configuration (as a
stand-alone command. the rx filtering is done automatically
according to the active role).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In order to keep to driver compiling during the patchset,
while avoiding one-huge-patch, temporarily disable some
advanced ap functions.
These changes will be reverted later in the patchset, as
part of the patches for advanced ap functions support.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This does not make sense in fw >= 6/7.3.0.0.75 (wl127x/wl128x) -
we don't use Tx blocks to measure FW occupancy anymore.
This reverts commit 9e374a37b6.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix the value of PG version for 128x at sysfs, remove write permissions
from PG version (hw_pg_ver) in sysfs and add remove files
(hw_pg_ver,bt_coex_state) from sysfs while freeing hardware.
New macro names for register Fuse_data_2_1 depend on architecture.
Propagate chip id through wiphy in PLT mode which still not work of
a bug in ethtool.
Signed-off-by: Gery Kahn <geryk@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In case of QoS packets the packet payload isn't aligned to
4 bytes. In that case the mac80211 layer take care of that
via memmove() in ieee80211_deliver_skb().
Add support of copy packets from aggregation buffer to the
skbs with packet payload aligned care. In case of QoS packets
copy the packets in offset of 2 bytes guarantee payload aligned
to 4 bytes.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
the comments are obselete as the virtual wiphy support was removed from
the driver
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for the ease of debugging, we display only the rate control statistics
for currently operating mode and bandwidth
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_FLAG_HT must be included when reporting MCS rates. Without
this, mac80211 ended up dropping any frame sent at MCS index 12
or higher and that resulted in oddly random looking errors in
mac80211_hwsim tests.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen reported that compilation fails if both ath6kl and ath9k are
compiled in:
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_start':
(.opd+0x600): multiple definition of `htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e40): first defined here
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_stop':
(.text+0x7b40): multiple definition of `.htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67b34): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_start':
(.text+0x7d18): multiple definition of `.htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67ba0): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_stop':
(.opd+0x5e8): multiple definition of `htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e28): first defined here
To fix this add ath6kl prefix to all public functions in htc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since kernel 3.0, the problems with controlling b43 devices that have
low-power (LP) PHYs have been fixed and the EXPERIMENTAL designation
can be fixed.
This patch also fixes a typo as the device supports 802.11b communications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always hit the goto and skip the printk(). The original code does
the right thing even though it looks messy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When toggle_irq is called for PCI devices to disable device interrupts
it used tasklet_disable to wait for a possibly running tasklet to finish.
However, on SMP systems the tasklet might still be scheduled on another CPU.
Instead, use tasklet_kill to ensure that all scheduled tasklets are finished
before returning from toggle_irq.
Furthermore, it was possible that a tasklet reenabled its interrupt even
though interrupts have been disabled already. Fix this by checking the
DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts
during tasklet processing.
While at it also enable/kill the TBTT and PRETBTT tasklets in the
toggle_irq callback and only use tasklet_kill in stop_queue to wait
for a currently scheduled beacon update before returning.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the driver no longer uses the raw r/w routines, remove their definitions.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIe driver used raw reads and writes on the PCIe hardware.
As all of these are only affecting the configuration space, all of
then can be converted to pci_{read,write}_config_XX calls.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spur frequency was incorrectly computed with 10Mhz offset
which could cause the filter would not notch out the spur
and also this could improve rx sensitivity in HT40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add code to display driver version information in dmesg after
loading the driver successfully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO card is now fully powered down when the network interface is
brought down.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the driver so that it does not function when the interface is
down, in preparation for runtime power management.
No commands can be run while the interface is down, so the ndo_dev_stop
routine now directly does all necessary work (including asking the device
to disconnect from the network and disabling multicast functionality)
directly.
power_save and power_restore hooks are added meaning that card drivers
can take steps to turn the device off when the interface is down.
The MAC address can now only be changed when all interfaces are down;
the new address will be programmed when an interface gets brought up.
This matches mac80211 behaviour.
Also, some small cleanups/simplifications were made in the surrounding
device handling logic.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The high_power tx gain table is changed to match the low_ob_db tx gain
table for both 5G and 2G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to process RxDone and ds_info status again in case
valid rx status is given.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleanups virtual wiphy specific frametype structure
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ieee80211 core was found on a Netgear wndr3400.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nowhere the firmware memory is freed, free it during
the device destroy process.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes, the network manager is failing to connect to the AP due
to the below kernel crash message. The reason behind this,
after issuing the connect command to the chip, the chip is sending
disconnect event and then immediately one connect event to the host
in some random cases.
The host driver resets all states (including cfg80211 state machine)
when it receives disconnect event from the chip. But, still the host
driver reports the next received connect event to cfg80211, at that time
cfg80211 SME state would have been in IDLE state, which was causing
the below kernel crash.
Now, host driver's sme state machine is checked every time before
delivering connect event to cfg80211
WARNING: at net/wireless/sme.c:517 cfg80211_connect_result+0x10d/0x120()
[..]
Call Trace:
[<c0145732>] warn_slowpath_common+0x72/0xa0
[<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
[<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
[<c0145782>] warn_slowpath_null+0x22/0x30
[<c05d676d>] cfg80211_connect_result+0x10d/0x120
[<f83ff497>] ath6kl_cfg80211_connect_event+0x427/0x4f0 [ath6kl]
[<c035d26a>] ? put_dec+0x2a/0xa0
[<c035d645>] ? number+0x365/0x380
[<c0154675>] ? mod_timer+0x135/0x260
[<c035e00e>] ? format_decode+0x2fe/0x370
[<c01263c8>] ? default_spin_lock_flags+0x8/0x10
[<c05fd91f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[<c0146032>] ? console_unlock+0x172/0x1c0
[<f8402659>] ath6kl_connect_event+0x89/0x400 [ath6kl]
[<f840826e>] ath6kl_wmi_control_rx+0x98e/0x1d60 [ath6kl]
[<c01335b5>] ? __wake_up+0x45/0x60
[<f84053aa>] ath6kl_rx+0x56a/0x770 [ath6kl]
[<c04d0242>] ? mmc_release_host+0x22/0x40
[<c04d9329>] ? sdio_release_host+0x19/0x30
[<f840a27a>] ? ath6kl_sdio_read_write_sync+0x7a/0xc0 [ath6kl]
[<f83f82b1>] do_rx_completion+0x41/0x50 [ath6kl]
[<f83faa6a>] htc_rxmsg_pending_handler+0x6ba/0xbd0 [ath6kl]
[<f8404bb0>] ? ath6kl_tx_data_cleanup+0x30/0x30 [ath6kl]
[<f840a1c0>] ? ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
[<f83f7cd5>] ath6kldev_intr_bh_handler+0x2a5/0x630 [ath6kl]
[<f840a1c0>] ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
[<c04d97c7>] sdio_irq_thread+0xc7/0x2d0
[<c013aeb0>] ? default_wake_function+0x10/0x20
[<c012fc98>] ? __wake_up_common+0x48/0x70
[<c04d9700>] ? sdio_claim_irq+0x200/0x200
[<c0163854>] kthread+0x74/0x80
[<c01637e0>] ? kthread_worker_fn+0x160/0x160
[<c0604c06>] kernel_thread_helper+0x6/0x10
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use wlan_iterate_nodes() directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By having scan_table in struct ath6kl, it makes sense to move initialization
to ath6kl_init() and deinitialization to ath6kl_destroy().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Eliad Peller