ssb_wait_bit was designed for only one-bit bitmasks.
People start using it for multi-bit bitmasks. Make the "set" case
is safe for this. The "unset" case is already safe.
This does not change behavior of the current code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'fixes-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure MAYDAY_INITIAL_TIMEOUT is at least 2 jiffies long
workqueue, freezer: unify spelling of 'freeze' + 'able' to 'freezable'
workqueue: wake up a worker when a rescuer is leaving a gcwq
commit 9b5e383c11 (net: Introduce
unregister_netdevice_many()) left an active LIST_HEAD() in
rollback_registered(), with possible memory corruption.
Even if device is freed without touching its unreg_list (and therefore
touching the previous memory location holding LISTE_HEAD(single), better
close the bug for good, since its really subtle.
(Same fix for default_device_exit_batch() for completeness)
Reported-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Eric W. Biderman <ebiderman@xmission.com>
Tested-by: Eric W. Biderman <ebiderman@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
CC: stable <stable@kernel.org> [.33+]
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biderman and Michal Hocko reported various memory corruptions
that we suspected to be related to a LIST head located on stack, that
was manipulated after thread left function frame (and eventually exited,
so its stack was freed and reused).
Eric Dumazet suggested the problem was probably coming from commit
443457242b (net: factorize
sync-rcu call in unregister_netdevice_many)
This patch fixes __dev_close() and dev_close() to properly deinit their
respective LIST_HEAD(single) before exiting.
References: https://lkml.org/lkml/2011/2/16/304
References: https://lkml.org/lkml/2011/2/14/223
Reported-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Eric W. Biderman <ebiderman@xmission.com>
Tested-by: Eric W. Biderman <ebiderman@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0dbaee3b37 (net: Abstract default ADVMSS behind an
accessor.) introduced a possible crash in tcp_connect_init(), when
dst->default_advmss() is called from dst_metric_advmss()
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When list debugging is enabled, we aim to readably show list corruption
errors, and the basic list_add/list_del operations end up having extra
debugging code in them to do some basic validation of the list entries.
However, "list_del_init()" and "list_move[_tail]()" ended up avoiding
the debug code due to how they were written. This fixes that.
So the _next_ time we have list_move() problems with stale list entries,
we'll hopefully have an easier time finding them..
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add missing frac fb div flag for dce4+
drm/radeon/kms: do not reject X16 and Y16X16 floating-point formats on r300
drm/nouveau: fix suspend/resume on GPUs that don't have PM support
drm/nouveau: flips/flipd need to always set 'evict' for move_accel_cleanup()
drm/nv40: fix tiling-related setup for a number of chipsets
drm/nouveau: fix non-EDIDful native mode selection
drm/nouveau: Fix detection of DDC-based LVDS on DCB15 boards.
drm/nv04-nv40: Fix NULL dereference when we fail to find an LVDS native mode.
drm/nv10: Fix crash when allocating a BO larger than half the available VRAM.
Validate number of blocks in map and remove redundant variable.
Signed-off-by: Timo Warns <warns@pre-sense.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We believe that our earlier patch for supporting multiple hardware
receive queues per enic device requires more internal testing. At this
point, we think that it's best to disable the use of multiple receive
queues. The current patch provides an effective means for the same.
Also, we continue to disallow multiple hardware transmit queues per
device. But change the way we enforce this in order to maintain
consistency with the way receive queues are handled.
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Danny Guo <dannguo@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only troublesome bit here is __mkroute_output which wants
to override res->fi and res->type, compute those in local
variables instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC emits all kinds of crazy zero extensions when we go from signed
int, to unsigned short, etc. etc.
This transformation has to be legal because:
1) In tkey_extract_bits() in mask_pfx(), the values are used to
perform shifts, on which negative values are undefined by C.
2) In fib_table_lookup() we perform comparisons with unsigned
values, constants, and additions. None of which should
encounter negative values.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows avoiding multiple writes to the initial __refcnt.
The most simplest cases of wanting an initial reference of "1"
in ipv4 and ipv6 have been converted, the rest have been left
along and kept at the existing "0".
Signed-off-by: David S. Miller <davem@davemloft.net>
This also allows us to combine all the dst->flags settings and avoid
read/modify/write sequences to this struct member.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of redundancy and unnecessary stack frames
in the output route creation path.
1) Make __mkroute_output() return error pointers.
2) Eliminate ip_mkroute_output() entirely, made possible by #1.
3) Call __mkroute_output() directly and handling the returning error
pointers in ip_route_output_slow().
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-enables UIE timer/polling emulation for rtc devices
that do not support alarm irqs.
CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Uwe pointed out that my alarm based UIE emulation is not sufficient
to replace the older timer/polling based UIE emulation on devices
where there is no alarm irq. This causes rtc devices without alarms
to return -EINVAL to UIE ioctls. The fix is to re-instate the old
timer/polling method for devices without alarm irqs.
This patch reverts the following commits:
042620a018 - Remove UIE emulation
1daeddd596 - Cleanup removed UIE emulation declaration
b5cc8ca1c9 - Remove Kconfig symbol for UIE emulation
The emulation mode will still need to be wired-in with a following
patch before it will work.
CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
On hardware that doesn't support alarm interrupts, rtc_alarm_irq_enable
could return without releasing the ops_lock mutex.
This was introduced in
aa0be0f (RTC: Propagate error handling via rtc_timer_enqueue properly)
This patch corrects the issue by only returning once the mutex is
released.
[john.stultz: Reworded the commit log]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This also enables TSOv6, TSO-ECN, and UFO as loopback clearly can handle them.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce NETIF_F_RXCSUM to replace device-private flags for RX checksum
offload. Integrate it with ndo_fix_features.
ethtool_op_get_rx_csum() is removed altogether as nothing in-tree uses it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new framework to handle device features setting.
It consists of:
- new fields in struct net_device:
+ hw_features - features that hw/driver supports toggling
+ wanted_features - features that user wants enabled, when possible
- new netdev_ops:
+ feat = ndo_fix_features(dev, feat) - API checking constraints for
enabling features or their combinations
+ ndo_set_features(dev) - API updating hardware state to match
changed dev->features
- new ethtool commands:
+ ETHTOOL_GFEATURES/ETHTOOL_SFEATURES: get/set dev->wanted_features
and trigger device reconfiguration if resulting dev->features
changed
+ ETHTOOL_GSTRINGS(ETH_SS_FEATURES): get feature bits names (meaning)
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to enable GRO even if RX csum is disabled. GRO will not
be used for packets without hardware checksum anyway.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for unified offloads patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Danny Guo <dannguo@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a device reset, clear the counter for the no. of unicast addresses registered.
Also, rename the routines that update unicast and multicast address lists.
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Danny Guo <dannguo@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If management firmware is present and the device is down, the firmware
will assume control of the phy. If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior. This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without calling of netif_carrier_off at the end of the probe the operstate
is unknown when the device is initially opened. By default the carrier is
on so when the device is opened and netif_carrier_on is called the link
watch event is not fired and operstate remains zero (unknown).
This patch fixes this behavior in forcedeth and r8169.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a double completion associated with error handling for RC QPs.
The sequence is:
- The do_rc_ack() routine fields an RNR nack and there are 0
rnr_retries configured on the QP.
- qib_error_qp() stops the pending timer
- qib_rc_send_complete() is called from sdma_complete()
- qib_rc_send_complete() starts the timer because the msb of the psn
just completed says an ack is needed.
- a bunch of flushes occur as ipoib posts WQEs to an error'ed QP
- rc_timeout() calls qib_restart_rc()
- qib_restart_rc() calls qib_send_complete() with a
IB_WC_RETRY_EXC_ERR on a wqe that has already been completed in the
past
The fix avoids starting the timer since another packet will never
arrive.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use the existing filter management functions to insert TCP/IPv4 and
UDP/IPv4 4-tuple filters for Receive Flow Steering.
For each channel, track how many RFS filters are being added during
processing of received packets and scan the corresponding number of
table entries for filters that may be reclaimed. Do this in batches
to reduce lock overhead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Support fetching and retrieving RX indirection table via ethtool.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Büsch